Peter Rosin [Wed, 18 Dec 2019 12:28:28 +0000 (14:28 +0200)]
drm: atmel-hlcdc: prefer a lower pixel-clock than requested
The intention was to only select a higher pixel-clock rate than the
requested, if a slight overclocking would result in a rate significantly
closer to the requested rate than if the conservative lower pixel-clock
rate is selected. The fixed patch has the logic the other way around and
actually prefers the higher frequency. Fix that.
Signed-off-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Fixes: 9946a3a9dbed ("drm/atmel-hlcdc: allow selecting a higher pixel-clock than requested")
Reported-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Tested-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Cc: Boris Brezillon <boris.brezillon@bootlin.com>
Cc: <stable@vger.kernel.org> # v4.20+
Link: https://patchwork.freedesktop.org/patch/msgid/1576672109-22707-6-git-send-email-claudiu.beznea@microchip.com
Claudiu Beznea [Wed, 18 Dec 2019 12:28:25 +0000 (14:28 +0200)]
drm: atmel-hlcdc: enable clock before configuring timing engine
Changing pixel clock source without having this clock source enabled
will block the timing engine and the next operations after (in this case
setting ATMEL_HLCDC_CFG(5) settings in atmel_hlcdc_crtc_mode_set_nofb()
will fail). It is recomended (although in datasheet this is not present)
to actually enabled pixel clock source before doing any changes on timing
enginge (only SAM9X60 datasheet specifies that the peripheral clock and
pixel clock must be enabled before using LCD controller).
Fixes: 1a396789f65a ("drm: add Atmel HLCDC Display Controller support")
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Cc: Boris Brezillon <boris.brezillon@free-electrons.com>
Cc: <stable@vger.kernel.org> # v4.0+
Link: https://patchwork.freedesktop.org/patch/msgid/1576672109-22707-3-git-send-email-claudiu.beznea@microchip.com
Claudiu Beznea [Wed, 18 Dec 2019 12:28:24 +0000 (14:28 +0200)]
drm: atmel-hlcdc: use double rate for pixel clock only if supported
Doubled system clock should be used as pixel cock source only if this
is supported. This is emphasized by the value of
atmel_hlcdc_crtc::dc::desc::fixed_clksrc.
Fixes: a6eca2abdd42 ("drm: atmel-hlcdc: add config option for clock selection")
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Cc: Boris Brezillon <bbrezillon@kernel.org>
Cc: <stable@vger.kernel.org> # v5.3+
Link: https://patchwork.freedesktop.org/patch/msgid/1576672109-22707-2-git-send-email-claudiu.beznea@microchip.com
Sam Ravnborg [Mon, 6 Jan 2020 18:17:31 +0000 (19:17 +0100)]
dt-bindings: fix warnings in xinpeng,xpp055c272.yaml
The reg property in the example caused following warnings:
xinpeng,xpp055c272.example.dts:20.17-27: Warning (reg_format): /example-0/dsi@
ff450000/panel@0:reg: property has invalid length (4 bytes) (#address-cells == 2, #size-cells == 1)
xinpeng,xpp055c272.example.dt.yaml: Warning (pci_device_bus_num): Failed prerequisite 'reg_format'
xinpeng,xpp055c272.example.dt.yaml: Warning (i2c_bus_reg): Failed prerequisite 'reg_format'
xinpeng,xpp055c272.example.dt.yaml: Warning (spi_bus_reg): Failed prerequisite 'reg_format'
xinpeng,xpp055c272.example.dts:18.21-24.15: Warning (avoid_default_addr_size): /example-0/dsi@
ff450000/panel@0: Relying on default #address-cells value
xinpeng,xpp055c272.example.dts:18.21-24.15: Warning (avoid_default_addr_size): /example-0/dsi@
ff450000/panel@0: Relying on default #size-cells value
Added #address-cells and #size-cells to silence the warning.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Reviewed-by: Heiko Stuebner <heiko.stuebner@theobroma-systems.com>
Cc: Maxime Ripard <mripard@kernel.org>
Cc: Rob Herring <robh@kernel.org>
Cc: devicetree@vger.kernel.org
Link: https://patchwork.freedesktop.org/patch/msgid/20200106181731.GA24294@ravnborg.org
yu kuai [Thu, 26 Dec 2019 12:14:15 +0000 (20:14 +0800)]
drm/bridge: cdns: remove set but not used variable 'nlanes'
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/gpu/drm/bridge/cdns-dsi.c: In function ‘cdns_dsi_mode2cfg’:
drivers/gpu/drm/bridge/cdns-dsi.c:515:11: warning: variable ‘nlanes’
set but not used [-Wunused-but-set-variable]
It is never used, and so can be removed.
Signed-off-by: yu kuai <yukuai3@huawei.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191226121415.39483-1-yukuai3@huawei.com
yu kuai [Thu, 26 Dec 2019 12:12:07 +0000 (20:12 +0800)]
drm/bridge: cdns: remove set but not used variable 'bpp'
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/gpu/drm/bridge/cdns-dsi.c: In function
‘cdns_dsi_bridge_enable’:
drivers/gpu/drm/bridge/cdns-dsi.c:788:6: warning: variable ‘bpp’
set but not used [-Wunused-but-set-variable]
It is never used, and so can be removed.
Signed-off-by: yu kuai <yukuai3@huawei.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191226121207.2099-1-yukuai3@huawei.com
zhengbin [Mon, 16 Dec 2019 03:58:21 +0000 (11:58 +0800)]
drm: meson: Remove unneeded semicolon
Fixes coccicheck warning:
drivers/gpu/drm/meson/meson_crtc.c:360:3-4: Unneeded semicolon
drivers/gpu/drm/meson/meson_plane.c:181:2-3: Unneeded semicolon
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: zhengbin <zhengbin13@huawei.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1576468701-69717-1-git-send-email-zhengbin13@huawei.com
Julia Lawall [Wed, 1 Jan 2020 07:43:33 +0000 (08:43 +0100)]
drm: bridge: dw-hdmi: constify copied structure
The dw_hdmi_hw structure is only copied into another structure,
so make it const.
The opportunity for this change was found using Coccinelle.
Fixes: 7ed6c665e19d ("drm: bridge/dw_hdmi-ahb-audio: add audio driver")
Signed-off-by: Julia Lawall <Julia.Lawall@inria.fr>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1577864614-5543-16-git-send-email-Julia.Lawall@inria.fr
Thomas Zimmermann [Tue, 3 Dec 2019 08:38:19 +0000 (09:38 +0100)]
drm/hisilicon/hibmc: Export VRAM MM information to debugfs
This change makes information about VRAM consumption available on
debugfs. See
/sys/kernel/debug/dri/0/vram-mm
for an overview of how VRAM is being used.
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20191203083819.6643-6-tzimmermann@suse.de
Thomas Zimmermann [Tue, 3 Dec 2019 08:38:18 +0000 (09:38 +0100)]
drm/hisilicon/hibmc: Implement hibmc_dumb_create() with generic helpers
The hibmc driver aligns scanlines to 16 bytes. By using the new pitch_align
argument of drm_gem_vram_fill_create_dumb(), convert hibmc over.
v2:
* move changes to VRAM helpers into separate patch
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20191203083819.6643-5-tzimmermann@suse.de
Thomas Zimmermann [Tue, 3 Dec 2019 08:38:17 +0000 (09:38 +0100)]
drm/vram: Support scanline alignment for dumb buffers
Adding the pitch alignment as an argument to
drm_gem_vram_fill_create_dumb() allows to align scanlines to certain
offsets. A value of 0 disables scanline pitches.
v3:
* only do power-of-2 test if pitch_align given; fails otherwise
* mgag200: call drm_gem_vram_fill_create_dumb() with pitch_align
v2:
* split of patch from related hibmc changes
* test if scanline pitch is power of 2
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20191203083819.6643-4-tzimmermann@suse.de
Thomas Zimmermann [Tue, 3 Dec 2019 08:38:16 +0000 (09:38 +0100)]
drm/hisilicon/hibmc: Replace struct hibmc_framebuffer with generic code
The hibmc driver's struct hibmc_framebuffer stores a DRM framebuffer
with an associated GEM object. This functionality is also provided by
generic code. Switch hibmc over.
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20191203083819.6643-3-tzimmermann@suse.de
Thomas Zimmermann [Tue, 3 Dec 2019 08:38:15 +0000 (09:38 +0100)]
drm/hisilicon/hibmc: Switch to generic fbdev emulation
There's nothing special about hibmc's fbdev emulation that is not
provided by the generic implementation. Switch over and remove the
driver's code.
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20191203083819.6643-2-tzimmermann@suse.de
Nickey Yang [Wed, 11 Dec 2019 20:34:17 +0000 (21:34 +0100)]
drm: rockchip: rk3066_hdmi: set edid fifo address
Fix edid reading error when edid's block > 2.
Signed-off-by: Nickey Yang <nickey.yang@rock-chips.com>
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20191211203417.19448-1-jbx6244@gmail.com
Miquel Raynal [Tue, 24 Dec 2019 14:38:58 +0000 (15:38 +0100)]
drm/rockchip: lvds: Add PX30 support
Introduce PX30 LVDS support. This means adding the relevant helper
functions, a specific probe and also the initialization of a specific
PHY.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20191224143900.23567-10-miquel.raynal@bootlin.com
Maarten Lankhorst [Mon, 6 Jan 2020 09:35:33 +0000 (10:35 +0100)]
Merge drm/drm-next into drm-misc-next
Requested, and we need v5.5-rc1 backported as our current branch is still based on v5.4.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Miquel Raynal [Tue, 24 Dec 2019 14:38:57 +0000 (15:38 +0100)]
drm/rockchip: lvds: move hardware-specific functions together
Reorganize a bit the functions order to clarify the driver and separate
hardware independent and specific functions a bit. This change only moves
functions around, there is no functional change.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
[adapted to recent drm_panel_get_modes() param change ]
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20191224143900.23567-9-miquel.raynal@bootlin.com
Miquel Raynal [Tue, 24 Dec 2019 14:38:56 +0000 (15:38 +0100)]
drm/rockchip: lvds: improve error handling in helper functions
Return errors instead of returning void from internal helpers. When
these helpers are called, check the returned value and print an error
message in this case and not blindly continue.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20191224143900.23567-8-miquel.raynal@bootlin.com
Miquel Raynal [Tue, 24 Dec 2019 14:38:55 +0000 (15:38 +0100)]
drm/rockchip: lvds: Create an RK3288 specific probe function
The probe function is highly adapted to the RK3288 specificities, move
all specific bits into an "rk3288_probe" function, also part of the
platform data.
The goal is to ease the addition of new flavors of Rockchip LVDS IPs.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20191224143900.23567-7-miquel.raynal@bootlin.com
Miquel Raynal [Tue, 24 Dec 2019 14:38:54 +0000 (15:38 +0100)]
drm/rockchip: lvds: Change platform data to hold helper_funcs pointer
Prepare the introduction of PX30 support by using
drm_encoder_helper_funcs as platform data instead of multiple register
names which are specific to rk3288 and not generic to all Rockchip
IPs. This way adding support for a new flavor of a similar IP will be
a matter of adding the relevant helper funcs.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20191224143900.23567-6-miquel.raynal@bootlin.com
Miquel Raynal [Tue, 24 Dec 2019 14:38:53 +0000 (15:38 +0100)]
drm/rockchip: lvds: Harmonize function names
Prepare the introduction of PX30 support by clarifying the function
prefixes.
We continue to prefix with 'rockchip_lvds_' generic functions that are
not specific to a single hardware. Functions implying hardware
modifications are now prefixed with 'rk3288_lvds_'.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20191224143900.23567-5-miquel.raynal@bootlin.com
Miquel Raynal [Tue, 24 Dec 2019 14:38:52 +0000 (15:38 +0100)]
drm/rockchip: lvds: Fix indentation of a #define
Fix a #define indentation before adding more lines.
Fixes: 34cc0aa25456 ("drm/rockchip: Add support for Rockchip Soc LVDS")
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20191224143900.23567-4-miquel.raynal@bootlin.com
Miquel Raynal [Tue, 24 Dec 2019 14:38:51 +0000 (15:38 +0100)]
dt-bindings: display: rockchip-lvds: Document PX30 PHY
PX30 SoCs use a single PHY shared by two display pipelines: MIPI DSI
and LVDS. In the case of the LVDS IP, document the possibility to fill
a PHY handle.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20191224143900.23567-3-miquel.raynal@bootlin.com
Miquel Raynal [Tue, 24 Dec 2019 14:38:50 +0000 (15:38 +0100)]
dt-bindings: display: rockchip-lvds: Declare PX30 compatible
Document the PX30 LVDS compatible.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20191224143900.23567-2-miquel.raynal@bootlin.com
Heiko Stuebner [Tue, 24 Dec 2019 11:26:41 +0000 (12:26 +0100)]
drm/panel: add panel driver for Leadtek LTK500HD1829
The LTK500HD1829 is 5.5" DSI display.
v5:
- Fix some trivial checkpatch warnings while applying (sam)
changes in v4:
- drop error message if backlight not found, no other panel
does that and if needed it should live in drm_panel_of_backlight
changes in v3:
- drop one more overlooked panel->drm access
Signed-off-by: Heiko Stuebner <heiko.stuebner@theobroma-systems.com>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20191224112641.30647-3-heiko@sntech.de
Heiko Stuebner [Tue, 24 Dec 2019 11:26:40 +0000 (12:26 +0100)]
dt-bindings: display: panel: Add binding document for Leadtek LTK500HD1829
The LTK500HD1829 is a 5.0" 720x1280 DSI display.
v3:
- fixed example by adding address,size-cells (sam)
changes in v2:
- fix id (Maxime)
- drop port (Maxime)
Signed-off-by: Heiko Stuebner <heiko.stuebner@theobroma-systems.com>
Acked-by: Maxime Ripard <mripard@kernel.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20191224112641.30647-2-heiko@sntech.de
Heiko Stuebner [Tue, 24 Dec 2019 11:26:39 +0000 (12:26 +0100)]
dt-bindings: Add vendor prefix for Leadtek Technology
Shenzhen Leadtek Technology Co., Ltd. produces for example display
and touch panels.
Signed-off-by: Heiko Stuebner <heiko.stuebner@theobroma-systems.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20191224112641.30647-1-heiko@sntech.de
Heiko Stuebner [Tue, 24 Dec 2019 11:29:07 +0000 (12:29 +0100)]
drm/panel: add panel driver for Xinpeng XPP055C272 panels
Base on the somewhat similar Rocktech driver but adapted for
panel-specific init of the XPP055C272.
changes in v5:
- drop error message when backlight not found, no other panel
does that and if needed it should live in drm_panel_of_backlight
changes in v4:
none
changes in v3:
- remove wrong negative sync flags from display-mode to fix a display
artifact of the output getting move a tiny bit to the right
changes in v2:
- move to drm-panel-internal backlight handling (Sam)
- adapt to changes that happened to drm_panel structs+functions (Sam)
- sort includes (Sam)
- drop unnecessary DRV_NAME constant (Sam)
- do mipi_dsi_dcs_exit_sleep_mode and mipi_dsi_dcs_set_display_on
in panel prepare (not init_sequence) to keep symmetric (Sam)
Signed-off-by: Heiko Stuebner <heiko.stuebner@theobroma-systems.com>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20191224112907.30758-3-heiko@sntech.de
Heiko Stuebner [Tue, 24 Dec 2019 11:29:06 +0000 (12:29 +0100)]
dt-bindings: display: panel: Add binding document for Xinpeng XPP055C272
The XPP055C272 is a 5.5" 720x1280 DSI display.
changes in v4:
- fix id (Maxime)
- drop port (Maxime)
changes in v2:
- add size info into binding title (Sam)
- add more required properties (Sam)
Signed-off-by: Heiko Stuebner <heiko.stuebner@theobroma-systems.com>
Reviewed-by: Sam Ravnborg <sam@ravnborg.org>
Acked-by: Maxime Ripard <mripard@kernel.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20191224112907.30758-2-heiko@sntech.de
Heiko Stuebner [Tue, 24 Dec 2019 11:29:05 +0000 (12:29 +0100)]
dt-bindings: Add vendor prefix for Xinpeng Technology
Shenzhen Xinpeng Technology Co., Ltd produces for example display panels.
Signed-off-by: Heiko Stuebner <heiko.stuebner@theobroma-systems.com>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20191224112907.30758-1-heiko@sntech.de
Andrew F. Davis [Wed, 16 Oct 2019 18:04:24 +0000 (14:04 -0400)]
omapfb/dss: remove unneeded conversions to bool
Found with scripts/coccinelle/misc/boolconv.cocci.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Cc: Jiri Kosina <trivial@kernel.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191016180424.23907-1-afd@ti.com
Markus Elfring [Thu, 19 Sep 2019 14:51:38 +0000 (16:51 +0200)]
video: pxafb: Use devm_platform_ioremap_resource() in pxafb_probe()
Simplify this function implementation by using a known wrapper function.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Cc: Daniel Mack <daniel@zonque.org>
Cc: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Cc: "Rafael J. Wysocki" <rafael.j.wysocki@intel.com>
Cc: Viresh Kumar <viresh.kumar@linaro.org>
Cc: YueHaibing <yuehaibing@huawei.com>
Cc: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Cc: Himanshu Jha <himanshujha199640@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/a1b804b1-43c2-327a-d6d1-df49aebec680@web.de
Markus Elfring [Thu, 19 Sep 2019 14:26:56 +0000 (16:26 +0200)]
video: ocfb: Use devm_platform_ioremap_resource() in ocfb_probe()
Simplify this function implementation by using a known wrapper function.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Cc: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Cc: Himanshu Jha <himanshujha199640@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/61b75aa6-ff92-e0ed-53f2-50a95d93d1f6@web.de
Gustavo A. R. Silva [Wed, 11 Sep 2019 11:36:04 +0000 (06:36 -0500)]
video: fbdev: fsl-diu-fb: mark expected switch fall-throughs
Mark switch cases where we are expecting to fall through.
Fix the following warnings (Building: mpc512x_defconfig powerpc):
drivers/video/fbdev/fsl-diu-fb.c: In function ‘fsl_diu_ioctl’:
./include/linux/device.h:1750:2: warning: this statement may fall through [-Wimplicit-fallthrough=]
_dev_warn(dev, dev_fmt(fmt), ##__VA_ARGS__)
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/video/fbdev/fsl-diu-fb.c:1287:3: note: in expansion of macro ‘dev_warn’
dev_warn(info->dev,
^~~~~~~~
drivers/video/fbdev/fsl-diu-fb.c:1290:2: note: here
case MFB_SET_PIXFMT:
^~~~
In file included from ./include/linux/acpi.h:15:0,
from ./include/linux/i2c.h:13,
from ./include/uapi/linux/fb.h:6,
from ./include/linux/fb.h:6,
from drivers/video/fbdev/fsl-diu-fb.c:20:
./include/linux/device.h:1750:2: warning: this statement may fall through [-Wimplicit-fallthrough=]
_dev_warn(dev, dev_fmt(fmt), ##__VA_ARGS__)
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/video/fbdev/fsl-diu-fb.c:1296:3: note: in expansion of macro ‘dev_warn’
dev_warn(info->dev,
^~~~~~~~
drivers/video/fbdev/fsl-diu-fb.c:1299:2: note: here
case MFB_GET_PIXFMT:
^~~~
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Cc: Timur Tabi <timur@kernel.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190911113604.GA31512@embeddedor
Colin Ian King [Fri, 6 Sep 2019 18:11:14 +0000 (19:11 +0100)]
fbdev: matrox: make array wtst_xlat static const, makes object smaller
Don't populate the array wtst_xlat on the stack but instead make it
static const. Makes the object code smaller by 89 bytes.
Before:
text data bss dec hex filename
14347 840 0 15187 3b53 fbdev/matrox/matroxfb_misc.o
After:
text data bss dec hex filename
14162 936 0 15098 3afa fbdev/matrox/matroxfb_misc.o
(gcc version 9.2.1, amd64)
Signed-off-by: Colin Ian King <colin.king@canonical.com>
[b.zolnierkie: use u8 while at it (suggested by Ville Syrjälä)]
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190906181114.31414-1-colin.king@canonical.com
YueHaibing [Wed, 4 Sep 2019 11:57:54 +0000 (19:57 +0800)]
fbdev/sa1100fb: use devm_platform_ioremap_resource() to simplify code
Use devm_platform_ioremap_resource() to simplify the code a bit.
This is detected by coccinelle.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Viresh Kumar <viresh.kumar@linaro.org>
Cc: "Rafael J. Wysocki" <rafael.j.wysocki@intel.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190904115754.21612-1-yuehaibing@huawei.com
YueHaibing [Wed, 4 Sep 2019 11:55:23 +0000 (19:55 +0800)]
fbdev: s3c-fb: use devm_platform_ioremap_resource() to simplify code
Use devm_platform_ioremap_resource() to simplify the code a bit.
This is detected by coccinelle.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Acked-by: Jingoo Han <jingoohan1@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190904115523.25068-1-yuehaibing@huawei.com
YueHaibing [Wed, 4 Sep 2019 11:54:06 +0000 (19:54 +0800)]
fbdev: omapfb: use devm_platform_ioremap_resource() to simplify code
Use devm_platform_ioremap_resource() to simplify the code a bit.
This is detected by coccinelle.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Alexios Zavras <alexios.zavras@intel.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Allison Randal <allison@lohutok.net>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190904115406.23880-1-yuehaibing@huawei.com
Souptick Joarder [Mon, 2 Sep 2019 12:49:04 +0000 (18:19 +0530)]
video/fbdev/
68328fb: Remove dead code
This is dead code since 3.15. If their is no plan to
use it further, these can be removed forever.
Signed-off-by: Souptick Joarder <jrdr.linux@gmail.com>
Cc: Sabyasachi Gupta <sabyasachi.linux@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1567428544-8620-1-git-send-email-jrdr.linux@gmail.com
Christophe JAILLET [Sat, 31 Aug 2019 10:00:24 +0000 (12:00 +0200)]
pxa168fb: Fix the function used to release some memory in an error handling path
In the probe function, some resources are allocated using 'dma_alloc_wc()',
they should be released with 'dma_free_wc()', not 'dma_free_coherent()'.
We already use 'dma_free_wc()' in the remove function, but not in the
error handling path of the probe function.
Also, remove a useless 'PAGE_ALIGN()'. 'info->fix.smem_len' is already
PAGE_ALIGNed.
Fixes: 638772c7553f ("fb: add support of LCD display controller on pxa168/910 (base layer)")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Reviewed-by: Lubomir Rintel <lkundrak@v3.sk>
CC: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190831100024.3248-1-christophe.jaillet@wanadoo.fr
Peter Rosin [Tue, 27 Aug 2019 11:09:26 +0000 (11:09 +0000)]
fbdev: fbmem: avoid exporting fb_center_logo
The variable is only ever used from fbcon.c which is linked into the
same module. Therefore, the export is not needed.
Signed-off-by: Peter Rosin <peda@axentia.se>
Reviewed-by: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: Matthew Wilcox <willy@infradead.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190827110854.12574-4-peda@axentia.se
Peter Rosin [Tue, 27 Aug 2019 11:09:21 +0000 (11:09 +0000)]
fbdev: fbmem: allow overriding the number of bootup logos
Probably most useful if you want no logo at all, or if you only want one
logo regardless of how many CPU cores you have.
Signed-off-by: Peter Rosin <peda@axentia.se>
Reviewed-by: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: Matthew Wilcox <willy@infradead.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190827110854.12574-3-peda@axentia.se
Peter Rosin [Tue, 27 Aug 2019 11:09:16 +0000 (11:09 +0000)]
fbdev: fix numbering of fbcon options
Three shall be the number thou shalt count, and the number of the
counting shall be three. Four shalt thou not count...
One! Two! Five!
Fixes: efb985f6b265 ("[PATCH] fbcon: Console Rotation - Add framebuffer console documentation")
Signed-off-by: Peter Rosin <peda@axentia.se>
Reviewed-by: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: Matthew Wilcox <willy@infradead.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190827110854.12574-2-peda@axentia.se
Bartlomiej Zolnierkiewicz [Thu, 27 Jun 2019 14:08:43 +0000 (16:08 +0200)]
video: fbdev: mmp: fix sparse warnings about using incorrect types
Use ->screen_buffer instead of ->screen_base in mmpfb driver.
[ Please see commit
17a7b0b4d974 ("fb.h: Provide alternate screen_base
pointer") for details. ]
Also fix all other sparse warnings about using incorrect types in
mmp display subsystem.
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/ee796b43-f200-d41a-b18c-ae3d6bcaaa67@samsung.com
Bartlomiej Zolnierkiewicz [Thu, 27 Jun 2019 14:07:43 +0000 (16:07 +0200)]
video: fbdev: mmp: add COMPILE_TEST support
Add COMPILE_TEST support to mmp display subsystem for better compile
testing coverage.
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/d21a19ea-8c18-80df-ae79-76de7c5ee67c@samsung.com
Bartlomiej Zolnierkiewicz [Thu, 27 Jun 2019 14:07:03 +0000 (16:07 +0200)]
video: fbdev: mmp: remove duplicated MMP_DISP dependency
This dependency is already present in higher level Kconfig file
(drivers/video/fbdev/mmp/Kconfig).
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/eb28587c-4f8f-f044-1b8b-317a8d7967aa@samsung.com
Dave Airlie [Fri, 3 Jan 2020 01:43:31 +0000 (11:43 +1000)]
Merge tag 'drm-misc-next-2020-01-02' of git://anongit.freedesktop.org/drm/drm-misc into drm-next
drm-misc-next for v5.6:
UAPI Changes:
- Commandline parser: Add support for panel orientation, and per-mode options.
- Fix IOCTL naming for dma-buf heaps.
Cross-subsystem Changes:
- Rename DMA_HEAP_IOC_ALLOC to DMA_HEAP_IOCTL_ALLOC before it becomes abi.
- Change DMA-BUF system-heap's name to system.
- Fix leak in error handling in dma_heap_ioctl(), and make a symbol static.
- Fix udma-buf cpu access.
- Fix ti devicetree bindings.
Core Changes:
- Add CTA-861-G modes with VIC >= 193.
- Change error handling and remove bug_on in *drm_dev_init.
- Export drm_panel_of_backlight() correctly once more.
- Add support for lvds decoders.
- Convert drm/client and drm/(gem-,)fb-helper to drm-device based logging and update logging todo.
Driver Changes:
- Add support for dsi/px30 to rockchip.
- Add fb damage support to virtio.
- Use dma_resv locking wrappers in vc4, msm, etnaviv.
- Make functions in virtio static, and perform some simplifications.
- Add suspend support to sun4i.
- Add A64 mipi dsi support to sun4i.
- Add runtime pm suspend to komeda.
- Associated driver fixes.
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/efc11139-1653-86bc-1b0f-0aefde219850@linux.intel.com
Geert Uytterhoeven [Mon, 30 Dec 2019 13:06:04 +0000 (14:06 +0100)]
drm/mipi_dbi: Fix off-by-one bugs in mipi_dbi_blank()
When configuring the frame memory window, the last column and row
numbers are written to the column resp. page address registers. These
numbers are thus one less than the actual window width resp. height.
While this is handled correctly in mipi_dbi_fb_dirty() since commit
03ceb1c8dfd1e293 ("drm/tinydrm: Fix setting of the column/page end
addresses."), it is not in mipi_dbi_blank(). The latter still forgets
to subtract one when calculating the most significant bytes of the
column and row numbers, thus programming wrong values when the display
width or height is a multiple of 256.
Fixes: 02dd95fe31693626 ("drm/tinydrm: Add MIPI DBI support")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20191230130604.31006-1-geert+renesas@glider.be
Wambui Karuga [Mon, 30 Dec 2019 19:56:09 +0000 (22:56 +0300)]
drm/panel: declare variable as __be16
Declare the temp variable as __be16 to address the following sparse
warning:
drivers/gpu/drm/panel/panel-lg-lg4573.c:45:20: warning: incorrect type in initializer (different base types)
drivers/gpu/drm/panel/panel-lg-lg4573.c:45:20: expected unsigned short [unsigned] [usertype] temp
drivers/gpu/drm/panel/panel-lg-lg4573.c:45:20: got restricted __be16 [usertype] <noident>
Signed-off-by: Wambui Karuga <wambui.karugax@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20191230195609.12386-1-wambui.karugax@gmail.com
james qian wang (Arm Technology China) [Thu, 12 Dec 2019 07:48:13 +0000 (07:48 +0000)]
drm/komeda: Add runtime_pm support
- Add pm_runtime_get/put to crtc_enable/disable along with the real
display usage
- Add runtime_get/put to register_show, since register_show() will
access register, need to wakeup HW.
- For the case that PM is not enabled or configured, manually wakeup HW
Signed-off-by: james qian wang (Arm Technology China) <james.qian.wang@arm.com>
Reviewed-by: Mihail Atanassov <mihail.atanassov@arm.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191212074756.14678-1-james.qian.wang@arm.com
Dave Airlie [Fri, 27 Dec 2019 05:25:04 +0000 (15:25 +1000)]
Merge tag 'drm-intel-next-2019-12-23' of git://anongit.freedesktop.org/drm/drm-intel into drm-next
i915 features for v5.6:
- Separate hardware and uapi state (Maarten)
- Expose a number of sprite and plane formats (Ville)
- DDC symlink in HDMI connector sysfs directory (Andrzej Pietrasiewicz)
- Improve obj->mm.lock nesting lock annotation (Daniel)
(Includes lockdep changes)
- Selftest improvements across the board (Chris)
- ICL/TGL VDSC support on DSI (Jani, Vandita)
- TGL DSB fixes (Animesh, Lucas, Tvrtko)
- VBT parsing improvements and fixes (Lucas, Matt, José, Jani, Dan Carpenter)
- Fix LPSS vs. PMIC PWM backlight use on BYT/CHT (Hans)
(Includes ACPI+MFD changes)
- Display state, crtc, plane code refactoring (Ville)
- Set opregion chpd value to indicate the driver handles hotplug (Hans de Goede)
- DSI updates and fixes, TGL pipe D support, port mapping (José, Jani, Vandita)
- Make HDCP 2.2 support cover CFL (Juston Li)
- Fix CML PCI IDs and ULT (Shawn Lee)
- CMP-V PCH fix (Imre)
- TGL: Add another TGL PCH ID (James)
- EHL/JSL: Add new PCI IDs (James)
- Rename pipe update tracepoints (Ville)
- Fix FBC on GLK+ (Ville)
- GuC fixes and improvements (Daniele, Don Hiatt, Stuart Summers, Matthew Brost)
- Display debugfs improvements (Ville)
- Hotplug/irq fixes (Matt)
- PSR fixes and improvements (José)
- DRM_I915_GEM_MMAP_OFFSET ioctl (Abdiel)
- Static analysis fixes (Colin Ian King)
- Register sysctl path globally (Venkata Sandeep Dhanalakota)
- Introduce new macros for tracing (Venkata Sandeep Dhanalakota)
- Migrate gt towards intel_uncore_read/write (Andi)
- Add rps frequency translation helpers (Andi)
- Fix TGL transcoder clock off sequence (José)
- Fix TGL port A audio (Kai Vehmanen)
- TGL render decompression (DK)
- GEM/GT improvements and fixes across the board (Chris)
- Couple of backmerges (Jani)
Signed-off-by: Dave Airlie <airlied@redhat.com>
# gpg: Signature made Tue 24 Dec 2019 03:20:48 AM AEST
# gpg: using RSA key
D398079D26ABEE6F
# gpg: Good signature from "Jani Nikula <jani.nikula@intel.com>"
# gpg: WARNING: This key is not certified with a trusted signature!
# gpg: There is no indication that the signature belongs to the owner.
# Primary key fingerprint: 1565 A65B 77B0 632E 1124 E59C D398 079D 26AB EE6F
# Conflicts:
# drivers/gpu/drm/i915/display/intel_fbc.c
# drivers/gpu/drm/i915/gt/intel_lrc.c
# drivers/gpu/drm/i915/i915_gem.c
From: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/87lfr3rkry.fsf@intel.com
james qian wang (Arm Technology China) [Thu, 12 Dec 2019 07:27:55 +0000 (07:27 +0000)]
drm/komeda: Add event handling for EMPTY/FULL
EMPTY/FULL are HW input/output FIFO condition identifer, which are
useful information for addressing the problem, so expose them.
Signed-off-by: james qian wang (Arm Technology China) <james.qian.wang@arm.com>
Reviewed-by: Mihail Atanassov <mihail.atanassov@arm.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191212072737.30116-1-james.qian.wang@arm.com
Jagan Teki [Sun, 22 Dec 2019 13:22:27 +0000 (18:52 +0530)]
drm/sun4i: dsi: Add Allwinner A64 MIPI DSI support
The MIPI DSI controller in Allwinner A64 is similar to A33.
But unlike A33, A64 doesn't have DSI_SCLK gating so add compatible
for Allwinner A64 with uninitialized has_mod_clk driver.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Tested-by: Merlijn Wajer <merlijn@wizzup.org>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20191222132229.30276-6-jagan@amarulasolutions.com
Jagan Teki [Sun, 22 Dec 2019 13:22:26 +0000 (18:52 +0530)]
drm/sun4i: dsi: Handle bus clock via regmap_mmio_attach_clk
regmap has special API to enable the controller bus clock while
initializing register space, and current driver is using
devm_regmap_init_mmio_clk which require to specify bus
clk_id argument as "bus"
But, the usage of clocks are varies between different Allwinner
DSI controllers. Clocking in A33 would need bus and mod clocks
where as A64 would need only bus clock.
Since A64 support only single bus clock, it is optional to
specify the clock-names on the controller device tree node.
So using NULL on clk_id would get the attached clock.
To support clk_id as "bus" and "NULL" during clock enablement
between controllers, this patch add generic code to handle
the bus clock using regmap_mmio_attach_clk with associated
regmap APIs.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20191222132229.30276-5-jagan@amarulasolutions.com
Jagan Teki [Sun, 22 Dec 2019 13:22:25 +0000 (18:52 +0530)]
drm/sun4i: dsi: Get the mod clock for A31
As per the user manual, look like mod clock is not mandatory
for all Allwinner MIPI DSI controllers, it is connected to
CLK_DSI_SCLK for A31 and not available in A64.
So, add compatible check for A31 and get mod clock accordingly.
Tested-by: Merlijn Wajer <merlijn@wizzup.org>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20191222132229.30276-4-jagan@amarulasolutions.com
Jagan Teki [Sun, 22 Dec 2019 13:22:24 +0000 (18:52 +0530)]
dt-bindings: sun6i-dsi: Add A64 DPHY compatible (w/ A31 fallback)
The MIPI DSI PHY controller on Allwinner A64 is similar
on the one on A31.
Add A64 compatible and append A31 compatible as fallback.
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20191222132229.30276-3-jagan@amarulasolutions.com
Jagan Teki [Sun, 22 Dec 2019 13:22:23 +0000 (18:52 +0530)]
dt-bindings: sun6i-dsi: Document A64 MIPI-DSI controller
The MIPI DSI controller in Allwinner A64 is similar to A33.
But unlike A33, A64 doesn't have DSI_SCLK gating so it is valid
to have separate compatible for A64 on the same driver.
DSI_SCLK uses mod clock-names on dt-bindings, so the same
is not required for A64.
On that note
- A64 require minimum of 1 clock like the bus clock
- A33 require minimum of 2 clocks like both bus, mod clocks
So, update dt-bindings so-that it can document both A33,
A64 bindings requirements.
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20191222132229.30276-2-jagan@amarulasolutions.com
Ondrej Jirman [Tue, 29 Oct 2019 11:28:46 +0000 (12:28 +0100)]
drm: sun4i: Add support for suspending the display driver
Shut down the display engine during suspend.
Signed-off-by: Ondrej Jirman <megous@megous.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20191029112846.3604925-1-megous@megous.com
Jani Nikula [Mon, 23 Dec 2019 17:08:14 +0000 (19:08 +0200)]
drm/i915: Update DRIVER_DATE to
20191223
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Chris Wilson [Sun, 22 Dec 2019 23:35:58 +0000 (23:35 +0000)]
drm/i915: Mark the GEM context link as RCU protected
The only protection for intel_context.gem_cotext is granted by RCU, so
annotate it as a rcu protected pointer and carefully dereference it in
the few occasions we need to use it.
Fixes: 9f3ccd40acf4 ("drm/i915: Drop GEM context as a direct link from i915_request")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Andi Shyti <andi.shyti@intel.com>
Acked-by: Andi Shyti <andi.shyti@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191222233558.2201901-1-chris@chris-wilson.co.uk
Chris Wilson [Sun, 22 Dec 2019 21:02:55 +0000 (21:02 +0000)]
drm/i915: Introduce a vma.kref
Start introducing a kref on i915_vma in order to protect the vma unbind
(i915_gem_object_unbind) from a parallel destruction (i915_vma_parked).
Later, we will use the refcount to manage all access and turn i915_vma
into a first class container.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Imre Deak <imre.deak@intel.com>
Acked-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191222210256.2066451-2-chris@chris-wilson.co.uk
Chris Wilson [Sun, 22 Dec 2019 21:02:54 +0000 (21:02 +0000)]
drm/i915: Add a simple is-bound check before unbinding
Only acquire the various atomic references required to unbind the vma if
we do need to unbind the vma.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Acked-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191222210256.2066451-1-chris@chris-wilson.co.uk
Imre Deak [Sat, 21 Dec 2019 12:05:43 +0000 (14:05 +0200)]
drm/i915: Make sure CCS YUV semiplanar format checks work
For CCS formats, the current DRM core check for YUV semiplanar formats
doesn't work; use an i915 specific function for that.
v2: Fix checkpatch warnings.
Cc: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Mika Kahola <mika.kahola@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Mika Kahola <mika.kahola@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191221120543.22816-11-imre.deak@intel.com
Imre Deak [Sat, 21 Dec 2019 12:05:42 +0000 (14:05 +0200)]
drm/i915: Make sure Y slave planes get all the required state
Y planes program the offset and stride of the AUX plane, so make sure we
copy the required info for this into their plane state.
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Cc: Mika Kahola <mika.kahola@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Mika Kahola <mika.kahola@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191221120543.22816-10-imre.deak@intel.com
Dhinakaran Pandiyan [Sat, 21 Dec 2019 12:05:41 +0000 (14:05 +0200)]
drm/i915: Skip rotated offset adjustment for unsupported modifiers
During framebuffer creation, we pre-compute offsets for 90/270 plane
rotation. However, only Y and Yf modifiers support 90/270 rotation. So,
skip the calculations for other modifiers.
To keep the gem buffer size check still working for tiled planes, factor
out the logic needed for rotation setup and skip only this part for
tiled planes other than Y/Yf.
v2: Add a bounds check WARN for the rotation info array.
v3: Keep the gem buffer size check working for tiled planes.
Cc: Matt Roper <matthew.d.roper@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Mika Kahola <mika.kahola@intel.com>
Signed-off-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Mika Kahola <mika.kahola@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191221120543.22816-9-imre.deak@intel.com
Imre Deak [Sat, 21 Dec 2019 12:05:40 +0000 (14:05 +0200)]
drm/i915/tgl: Make sure FBs have a correct CCS plane stride
The CCS plane stride must be fixed on TGL, as it's not configurable for
the display. Instead the HW has a hardwired logic to determine it from
the main plane stride. Make sure userspace passes in the correct stride.
Cc: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Mika Kahola <mika.kahola@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Mika Kahola <mika.kahola@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191221120543.22816-8-imre.deak@intel.com
Dhinakaran Pandiyan [Sat, 21 Dec 2019 12:05:39 +0000 (14:05 +0200)]
drm/i915/tgl: Gen-12 render decompression
Gen-12 display decompression operates on Y-tiled compressed main surface.
The CCS is linear and has 4 bits of metadata for each main surface cache
line pair, a size ratio of 1:256. Gen-12 display decompression is
incompatible with buffers compressed by earlier GPUs, so make use of a new
modifier to identify gen-12 compression. Another notable change is that
render decompression is supported on all planes except cursor and on all
pipes. Start by adding render decompression support for [A,X]BGR888 pixel
formats.
v2: Fix checkpatch warnings (Lucas)
v3:
Rebase, disable color clear, styling changes and modify
intel_tile_width_bytes and intel_tile_height to handle linear CCS
v4:
- Use format block descriptors and the i915 specific func to get the
subsampling for each color plane.
- Use helpers to convert between CCS and main planes.
v5:
- Fix subsampling returned by intel_fb_plane_get_subsampling() for
the CCS plane of the first plane.
v6:
- Rebased on v2 of patch 4.
v7:
- Fix plane dimensions during FB check.
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Matt Roper <matthew.d.roper@intel.com>
Cc: Nanley G Chery <nanley.g.chery@intel.com>
Cc: Jason Ekstrand <jason@jlekstrand.net>
Cc: Radhakrishna Sripada <radhakrishna.sripada@intel.com>
Signed-off-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Radhakrishna Sripada <radhakrishna.sripada@intel.com> (v6)
Link: https://patchwork.freedesktop.org/patch/msgid/20191221120543.22816-7-imre.deak@intel.com
Dhinakaran Pandiyan [Sat, 21 Dec 2019 12:05:38 +0000 (14:05 +0200)]
drm/framebuffer: Format modifier for Intel Gen-12 render compression
Gen-12 has a new compression format, add a new modifier to indicate that.
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Matt Roper <matthew.d.roper@intel.com>
Cc: Nanley G Chery <nanley.g.chery@intel.com>
Cc: Jason Ekstrand <jason@jlekstrand.net>
Cc: Mika Kahola <mika.kahola@intel.com>
Cc: dri-devel@lists.freedesktop.org
Signed-off-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Mika Kahola <mika.kahola@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191221120543.22816-6-imre.deak@intel.com
Imre Deak [Sat, 21 Dec 2019 12:05:37 +0000 (14:05 +0200)]
drm/i915: Add helpers to select correct ccs/aux planes
Using helpers instead of open coding this to select a CCS plane for a
main plane makes the code cleaner and less error-prone when the location
of CCS plane can be different based on the format (packed vs. YUV
semiplanar). The same applies to selecting an AUX plane which can be a
UV plane (for an uncompressed YUV semiplanar format), or a CCS plane.
Cc: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Mika Kahola <mika.kahola@intel.com>
Cc: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Mika Kahola <mika.kahola@intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191221120543.22816-5-imre.deak@intel.com
Dhinakaran Pandiyan [Sat, 21 Dec 2019 12:05:36 +0000 (14:05 +0200)]
drm/i915: Extract framebufer CCS offset checks into a function
intel_fill_fb_info() has grown quite large and wrapping the offset checks
into a separate function makes the loop a bit easier to follow.
v2: Skip the check for non-CCS planes. (Mika)
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Matt Roper <matthew.d.roper@intel.com>
Cc: Mika Kahola <mika.kahola@intel.com>
Signed-off-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Mika Kahola <mika.kahola@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191221120543.22816-4-imre.deak@intel.com
Dhinakaran Pandiyan [Sat, 21 Dec 2019 12:05:35 +0000 (14:05 +0200)]
drm/i915: Move CCS stride alignment W/A inside intel_fb_stride_alignment
Easier to read if all the alignment changes are in one place and contained
within a function.
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Matt Roper <matthew.d.roper@intel.com>
Cc: Mika Kahola <mika.kahola@intel.com>
Signed-off-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Mika Kahola <mika.kahola@intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191221120543.22816-3-imre.deak@intel.com
Dhinakaran Pandiyan [Sat, 21 Dec 2019 12:05:34 +0000 (14:05 +0200)]
drm/i915: Use intel_tile_height() instead of re-implementing
intel_tile_dims() computes tile height using size and width, when there
is already a function to do just that - intel_tile_height()
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Matt Roper <matthew.d.roper@intel.com>
Cc: Mika Kahola <mika.kahola@intel.com>
Signed-off-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Mika Kahola <mika.kahola@intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191221120543.22816-2-imre.deak@intel.com
Jani Nikula [Thu, 19 Dec 2019 15:56:51 +0000 (17:56 +0200)]
drm/i915/selftests: make mock_drm.h self-contained
Needs i915_drv.h because i915 gets dereferenced.
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191219155652.2666-2-jani.nikula@intel.com
Jani Nikula [Thu, 19 Dec 2019 15:56:50 +0000 (17:56 +0200)]
drm/i915/selftests: make mock_context.h self-contained
Fix the forward declaration.
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191219155652.2666-1-jani.nikula@intel.com
Jani Nikula [Thu, 19 Dec 2019 13:38:45 +0000 (15:38 +0200)]
drm/i915: fix comment for POWER_DOMAIN_TRANSCODER_VDSC_PW2
The power domain covers VDSC for DSI transcoder on ICL, and it's
pedantically about pipe, not transcoder, on TGL.
Reported-by: Vandita Kulkarni <vandita.kulkarni@intel.com>
Cc: Vandita Kulkarni <vandita.kulkarni@intel.com>
Reviewed-by: Vandita Kulkarni <vandita.kulkarni@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191219133845.9333-1-jani.nikula@intel.com
Andi Shyti [Sun, 22 Dec 2019 14:40:46 +0000 (14:40 +0000)]
drm/i915/gt: Move pm debug files into a gt aware debugfs
The GT system is becoming more and more a stand-alone system in
i915 and it's fair to assign it its own debugfs directory.
rc6, rps and llc debugfs files are gt related, move them into the
gt debugfs directory.
Signed-off-by: Andi Shyti <andi.shyti@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20191222144046.1674865-3-chris@chris-wilson.co.uk
Chris Wilson [Sun, 22 Dec 2019 14:40:45 +0000 (14:40 +0000)]
drm/i915/gt: Merge engine init/setup loops
Now that we don't need to create GEM contexts in the middle of engine
construction, we can pull the engine init/setup loops together.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Andi Shyti <andi.shyti@intel.com>
Reviewed-by: Andi Shyti <andi.shyti@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191222144046.1674865-2-chris@chris-wilson.co.uk
Chris Wilson [Sun, 22 Dec 2019 14:40:44 +0000 (14:40 +0000)]
drm/i915/gt: Pull intel_gt_init_hw() into intel_gt_resume()
Since intel_gt_resume() is always immediately proceeded by init_hw, pull
the call into intel_gt_resume, where we have the rpm and fw already
held.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Andi Shyti <andi.shyti@intel.com>
Reviewed-by: Andi Shyti <andi.shyti@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191222144046.1674865-1-chris@chris-wilson.co.uk
Chris Wilson [Sun, 22 Dec 2019 12:07:52 +0000 (12:07 +0000)]
drm/i915/gt: Pull GT initialisation under intel_gt_init()
Begin pulling the GT setup underneath a single GT umbrella; let intel_gt
take ownership of its engines! As hinted, the complication is the
lifetime of the probed engine versus the active lifetime of the GT
backends. We need to detect the engine layout early and keep it until
the end so that we can sanitize state on takeover and release.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Andi Shyti <andi.shyti@intel.com>
Acked-by: Andi Shyti <andi.shyti@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191222120752.1368352-1-chris@chris-wilson.co.uk
Thierry Reding [Fri, 6 Dec 2019 13:53:36 +0000 (14:53 +0100)]
drm/atomic: Spell CRTC consistently
CRTC is an abbreviation and should be all caps in prose. Update all
kerneldoc comments to use a consistent spelling.
v2: remove hunk unrelated to the CRTC spelling fixes
Reviewed-by: Thomas Zimmermann <tzimmermann@suse.de>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191206135336.2084564-2-thierry.reding@gmail.com
Thierry Reding [Fri, 6 Dec 2019 13:53:35 +0000 (14:53 +0100)]
drm: Fix a couple of typos, punctation and whitespace issues
These are just a couple of things that I came across as I was reading
through the code and comments.
v2: added one more hunk that ended up in the wrong patch
Reviewed-by: Thomas Zimmermann <tzimmermann@suse.de>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191206135336.2084564-1-thierry.reding@gmail.com
Chris Wilson [Sat, 21 Dec 2019 20:01:09 +0000 (20:01 +0000)]
drm/i915: Move i915_gem_init_contexts() earlier
As the GEM global context setup is now independent of the GT state
(although GT does currently still depend upon the global
i915->kernel_context), we can move its init earlier, leaving the gt init
ready to be extracted.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Andi Shyti <andi.shyti@intel.com>
Reviewed-by: Andi Shyti <andi.shyti@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191221200109.1202310-1-chris@chris-wilson.co.uk
Chris Wilson [Sat, 21 Dec 2019 18:02:04 +0000 (18:02 +0000)]
drm/i915/gt: Repeat wait_for_idle for retirement workers
Since we may retire timelines from secondary workers,
intel_gt_retire_requests() is not always a reliable indicator that all
pending retirements are complete. If we do detect secondary workers are
in progress, recommend intel_gt_wait_for_idle() to repeat the retirement
check.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Acked-by: Andi Shyti <andi.shyti@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191221180204.1201217-1-chris@chris-wilson.co.uk
Chris Wilson [Sat, 21 Dec 2019 16:03:24 +0000 (16:03 +0000)]
drm/i915: Remove i915->kernel_context
Allocate only an internal intel_context for the kernel_context, forgoing
a global GEM context for internal use as we only require a separate
address space (for our own protection).
Now having weaned GT from requiring ce->gem_context, we can stop
referencing it entirely. This also means we no longer have to create random
and unnecessary GEM contexts for internal use.
GEM contexts are now entirely for tracking GEM clients, and intel_context
the execution environment on the GPU.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Andi Shyti <andi.shyti@intel.com>
Acked-by: Andi Shyti <andi.shyti@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191221160324.1073045-1-chris@chris-wilson.co.uk
Chris Wilson [Sat, 21 Dec 2019 00:11:36 +0000 (00:11 +0000)]
drm/i915/selftests: Setup engine->retire for mock_engine
Enable and cleanup the engine->retire for the mock engine.
Fixes: dc93c9b69315 ("drm/i915/gt: Schedule request retirement when signaler idles")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Acked-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191221001136.720154-1-chris@chris-wilson.co.uk
Ville Syrjälä [Thu, 19 Dec 2019 11:14:30 +0000 (13:14 +0200)]
drm/i915: Introduce intel_crtc_state_alloc()
We have several places where we want to allocate a pristine
crtc state. Some of those currently call intel_crtc_state_reset()
to properly initialize all the non-zero defaults in the state, but
some places do not. Let's add intel_crtc_state_alloc() to do both
the alloc and the reset, and call that everywhere we need a fresh
crtc state.
v2: s/kzalloc/kmalloc/ since we memset() anyway (José)
Cc: José Roberto de Souza <jose.souza@intel.com>
Cc: Manasi Navare <manasi.d.navare@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191219111430.17527-1-ville.syrjala@linux.intel.com
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Yannick Fertré [Wed, 27 Nov 2019 10:23:38 +0000 (11:23 +0100)]
drm/stm: ltdc: move pinctrl to encoder mode set
The pin control must be set to default as soon as possible to
establish a good video link between tv & bridge hdmi
(encoder mode set is call before encoder enable).
Signed-off-by: Yannick Fertre <yannick.fertre@st.com>
Acked-by: Philippe Cornu <philippe.cornu@st.com>
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@st.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1574850218-13257-1-git-send-email-yannick.fertre@st.com
Chris Wilson [Fri, 13 Dec 2019 15:13:31 +0000 (15:13 +0000)]
drm/i915/execlists: Select arb on/off around batches based on preemption
Decide whether or not we need to disable arbitration within user batches
based on our intel_engine_has_preemption() flag.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191213151331.1788371-1-chris@chris-wilson.co.uk
Chris Wilson [Fri, 20 Dec 2019 10:12:30 +0000 (10:12 +0000)]
drm/i915: Push the use-semaphore marker onto the intel_context
Instead of rummaging through the intel_context to peek at the GEM
context in the middle of request submission to decide whether to use
semaphores, store that information on the intel_context itself.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Andi Shyti <andi.shyti@intel.com>
Reviewed-by: Andi Shyti <andi.shyti@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191220101230.256839-2-chris@chris-wilson.co.uk
Chris Wilson [Fri, 20 Dec 2019 10:12:29 +0000 (10:12 +0000)]
drm/i915: Drop GEM context as a direct link from i915_request
Keep the intel_context as being the primary state for i915_request, with
the GEM context a backpointer from the low level state for the rarer
cases we need client information. Our goal is to remove such references
to clients from the backend, and leave the HW submission agnostic to
client interfaces and self-contained.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Andi Shyti <andi.shyti@intel.com>
Reviewed-by: Andi Shyti <andi.shyti@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191220101230.256839-1-chris@chris-wilson.co.uk
Chris Wilson [Thu, 19 Dec 2019 23:29:32 +0000 (23:29 +0000)]
drm/i915/gt: Teach veng to defer the context allocation
Since we added the context_alloc callback to intel_context_ops, we can
safely install a custom hook for the deferred virtual context allocation.
This means that all new contexts behave the same upon creation,
simplifying later code.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Andi Shyti <andi.shyti@intel.com>
Reviewed-by: Andi Shyti <andi.shyti@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191219232932.189197-1-chris@chris-wilson.co.uk
Chris Wilson [Thu, 19 Dec 2019 22:13:44 +0000 (22:13 +0000)]
drm/i915/gt: Add breadcrumb retire to physical engine
Avoid adding the retire workers to the virtual engine so that we don't
end up in the unenviable situation of trying to free the virtual engine
while its worker remains active.
Fixes: dc93c9b69315 ("drm/i915/gt: Schedule request retirement when signaler idles")
Closes: https://gitlab.freedesktop.org/drm/intel/issues/867
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Acked-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191219221344.161523-1-chris@chris-wilson.co.uk
Daniel Vetter [Thu, 19 Dec 2019 16:17:22 +0000 (17:17 +0100)]
drm/todo: Updating logging todo
Jani has merged a new set of logging functions, which we hope to be
the One True solution now, pinky promises:
commit
fb6c7ab8718eb2543695d77ad8302ff81e8e1e32
Author: Jani Nikula <jani.nikula@intel.com>
Date: Tue Dec 10 14:30:43 2019 +0200
drm/print: introduce new struct drm_device based logging macros
Update the todo entry to match the new preference.
v2: Fix spelling issue Sam noticed.
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Sean Paul <sean@poorly.run>
Cc: Wambui Karuga <wambui.karugax@gmail.com>
Acked-by: Jani Nikula <jani.nikula@intel.com>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191219161722.2779994-1-daniel.vetter@ffwll.ch
Ville Syrjälä [Fri, 13 Dec 2019 13:34:53 +0000 (15:34 +0200)]
drm/i915: Rename pipe update tracepoints
All the other display related tracepoints use intel_ instead
if i915_ as the prefix. Do the same for the pipe update
tracepoints so I don't always have to spend time looking for
them.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191213133453.22152-6-ville.syrjala@linux.intel.com
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Ville Syrjälä [Fri, 13 Dec 2019 13:34:49 +0000 (15:34 +0200)]
drm/i915/fbc: Remove second redundant intel_fbc_pre_update() call
I fumbled the conflict resolution a bit when applying the
fbc vblank wait w/a. Because of that we now call intel_fbc_pre_update()
twice. Remove the second redundant call.
Reported-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191213133453.22152-2-ville.syrjala@linux.intel.com
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Ville Syrjälä [Fri, 13 Dec 2019 13:34:48 +0000 (15:34 +0200)]
drm/i915/fbc: Reject PLANE_OFFSET.y%4!=0 on icl+ too
icl and tgl are still affected by the modulo 4 PLANE_OFFSET.y
underrun issue. Reject such configurations on all gen9+ platforms.
Can be reproduced easily with the following sequence of
hardware poking:
while {
write FBC_CTL.enable=1
wait for vblank
write PLANE_OFFSET .x=0 .y=32
write PLANE_SURF
wait for vblank
# if PLANE_OFFSET.y is multiple of 4 the underrun won't happen
write PLANE_OFFSET .x=0 .y=31
write PLANE_SURF
wait for vblank
# extra vblank wait is required here presumably
# to get FBC into the proper state
wait for vblank
write FBC_CTL.enable=0
# underrun happens some time after FBC disable
wait for vblank
}
Both 8888 and 565 pixel formats and all tilinga formats
seem affected. Reproduced on KBL/GLK/ICL/TGL. BDW confirmed
not affected.
Closes: https://gitlab.freedesktop.org/drm/intel/issues/792
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191213133453.22152-1-ville.syrjala@linux.intel.com
Reviewed-by: Imre Deak <imre.deak@intel.com>
Colin Ian King [Thu, 19 Dec 2019 19:09:16 +0000 (19:09 +0000)]
drm/i915: fix uninitialized pointer reads on pointers to and from
Currently pointers to and from are not initialized and may contain
garbage values. This will cause uninitialized pointer reads in the
call to intel_frontbuffer_track and later checks to see if to and from
are null. Fix this by ensuring to and from are initialized to NULL.
Addresses-Coverity: ("Uninitialised pointer read)"
Fixes: da42104f589d ("drm/i915: Hold reference to intel_frontbuffer as we track activity")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20191219190916.24693-1-colin.king@canonical.com
Chris Wilson [Wed, 18 Dec 2019 21:05:45 +0000 (21:05 +0000)]
drm/i915/gt: Suppress threshold updates on RPS parking
When we park RPS, we set the GPU to run at minimum 'idle' frequency.
However, as the GPU is idle, we also disable the worker and RPS
interrupts - changing the RPS thresholds has no effect, it just incurs
extra changes to restore them when we unpark. So on parking, leave the
thresholds set to the current power level and so we expect them to be
valid for our restart.
References: https://gitlab.freedesktop.org/drm/intel/issues/848
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Andi Shyti <andi.shyti@intel.com>
Reviewed-by: Andi Shyti <andi.shyti@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191218210545.3975426-2-chris@chris-wilson.co.uk
Chris Wilson [Wed, 18 Dec 2019 21:05:44 +0000 (21:05 +0000)]
drm/i915/gt: Use non-forcewake writes for RPS
Use non-forcewaked writes to queue RPS register changes that will take
effect when the write buffer is flushed, rather than wake the mmio
device for immediate effect. This is so that we can avoid a slow
forcewake dance upon unparking, and at our irregular updates.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Andi Shyti <andi.shyti@intel.com>
Reviewed-by: Andi Shyti <andi.shyti@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191218210545.3975426-1-chris@chris-wilson.co.uk
Chris Wilson [Thu, 19 Dec 2019 12:43:53 +0000 (12:43 +0000)]
drm/i915/gt: Track engine round-trip times
Knowing the round trip time of an engine is useful for tracking the
health of the system as well as providing a metric for the baseline
responsiveness of the engine. We can use the latter metric for
automatically tuning our waits in selftests and when idling so we don't
confuse a slower system with a dead one.
Upon idling the engine, we send one last pulse to switch the context
away from precious user state to the volatile kernel context. We know
the engine is idle at this point, and the pulse is non-preemptible, so
this provides us with a good measurement of the round trip time. It also
provides us with faster engine parking for ringbuffer submission, which
is a welcome bonus (e.g. softer-rc6).
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Stuart Summers <stuart.summers@intel.com>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191219105043.4169050-1-chris@chris-wilson.co.uk
Link: https://patchwork.freedesktop.org/patch/msgid/20191219124353.8607-2-chris@chris-wilson.co.uk
projects / openwrt / staging / blogic.git / log