V4L/DVB (10512): tda1004x: Fix eeprom firmware load on boards with 16MHz Xtal

For i2c normal work, we need to slow down the bus speed. However, the
slow down breaks the eeprom firmware load. So, use normal speed for
eeprom booting and then restore the i2c speed after that.

It should also be noticed that no other I2C transfer should be in course
while booting from eeprom, otherwise, tda10046 goes into an instable
state. So, proper locking are needed at the i2c bus master.

Tested with saa7134 MSI TV @nyware A/D board, that comes with an eeprom
with firmware version 29.

Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

V4L/DVB (10511): saa7134: get rid of KBL

KBL is not needed on saa7134, so, let's remove it.

However, we should take some care to avoid opening the module while
initializing it. This issue exists with newer udev's that opens a device
as soon as the driver is registered. So, a proper lock is needed on
open.

Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

V4L/DVB (10509): saa7134-video: two int controls lack a step

Fix two broken controls where a step weren't specified. Without a step,
userspace apps won't allow to adjust such controls.

Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

V4L/DVB (10508): saa7134: Cleanup: remove unused waitqueue from struct

The waitqueue is never used. So, let's just remove it.

Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

V4L/DVB (10507): saa7134: Fix analog mode on devices that need to open an i2c gate

Some saa7134 devices require to open an i2c gate before tuning. This
patch fix the initialization for those devices.

The nxt200x_gate_ctrl() logic were returned back to the old place, since
we don't know how to close the gate. A future pacth could revert that
change and provide the proper close gate control, to avoid keeping it
open forever.

Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

V4L/DVB (10506): saa7134: move tuner init code to saa7134-cards

On certain devices, before opening a tuner, we need to open the tuner
gate via i2c.

This patch just moves the tuner probing code to the same place where
such i2c commands are handled, to make easier to fix this trouble on
later patches.

Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

V4L/DVB (10505): tda8290: Print an error if i2c_gate is not provided

While here, be sure that gate will be kept disabled if an error occurs.

Cc: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

V4L/DVB (10504): tda827x: Be sure that gate will be open/closed at the proper time

The gate control logic is broken: several routines just keep it open;
other rotines close it properly; there are even other routines that
assumes that it is open without really checking or opening it.

Instead of having to manually handle the gate control and having such
troubles, let a sub-routine take care of the gate, opening it before
i2c_transfer and closing it after that. This avoids leaving the gate
into a random state.

Cc: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

V4L/DVB (10502): saa7146: move v4l2 device registration to saa7146_vv.

Doing the v4l2_device registration in the saa7146 core will make it
dependent on v4l2, even for DVB-only boards. This registration and
unregistration belongs in saa7146_vv instead.

Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

V4L/DVB (10501): saa7146: prevent unnecessary loading of v4l2-common.

Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

V4L/DVB (10500): saa7146: setting control while capturing should return EBUSY, not EINVAL.

Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

V4L/DVB (10499): saa7146: convert saa7146 and mxb in particular to v4l2_subdev.

Modified mxb to load the i2c modules through v4l2_subdev. So no more probing.
Modified tea6415c and tea6420 to use the standard routing ops to do the
routing, rather than using private commands. Dropped the private commands
from tda9840 (they were never used except during initialization of the
module).

Added saa7146 support for VIDIOC_DBG_G_CHIP_IDENT.

Converted saa5246a and saa5249 to v4l2_subdev.

Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

V4L/DVB (10498): saa7146: the adapter class will be NULL when v4l2_subdev is used.

Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

V4L/DVB (10497): saa7146: i2c adapdata now points to v4l2_device.

Prepare for converting to v4l2_subdev.

Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

V4L/DVB (10496): saa7146: implement v4l2_device support.

Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

V4L/DVB (10490): v4l2: prefill ident and revision from v4l2_dbg_chip_ident.

Drivers that implement this always have to set the ident and revision
to V4L2_IDENT_NONE and 0. Do this in the v4l2 core so drivers don't have
to do this.

Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

V4L/DVB (10489): doc: use consistent naming conventions for vdev and v4l2_dev.

Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

V4L/DVB (10488): ivtv: cleanup naming conventions

Use consistent naming for pci_dev, v4l2_device and video_device.

Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

V4L/DVB (10487): doc: update hm12 documentation.

Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

V4L/DVB (10486): ivtv/cx18: fix g_fmt and try_fmt for raw video

The raw video device didn't report the image size correctly.

When setting a new image the image height has to be a multiple of 32 lines.

Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

V4L/DVB (10465): dsbr100: Add few lost mutex locks.

Patch adds two lost mutex locks.

Signed-off-by: Alexey Klimov <klimov.linux@gmail.com>
Signed-off-by: Douglas Schilling Landgraf <dougsland@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

V4L/DVB (10464): radio-si470x: use usb_make_path in usb-radio drivers

Place usb_make_path in radio-si470x.c that used when reporting bus_info
information in vidioc_querycap.

Acked-by: Tobias Lorenz <tobias.lorenz@gmx.net>
Signed-off-by: Alexey Klimov <klimov.linux@gmail.com>
Signed-off-by: Douglas Schilling Landgraf <dougsland@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

V4L/DVB (10463): radio-mr800: fix checking of retval after usb_bulk_msg

Patch corrects checking of returned value after usb_bulk_msg. Now we
also check if number of transferred bytes equals to BUFFER_LENGTH.

Signed-off-by: Alexey Klimov <klimov.linux@gmail.com>
Signed-off-by: Douglas Schilling Landgraf <dougsland@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

V4L/DVB (10462): radio-mr800: increase version and add comments

Increase driver version to 0.10, remove old and add new useful comments.

Signed-off-by: Alexey Klimov <klimov.linux@gmail.com>
Signed-off-by: Douglas Schilling Landgraf <dougsland@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

V4L/DVB (10461): radio-mr800: add few lost mutex locks

Patch adds two lost mutex locks.

Signed-off-by: Alexey Klimov <klimov.linux@gmail.com>
Signed-off-by: Douglas Schilling Landgraf <dougsland@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

V4L/DVB (10460): radio-mr800: add stereo support

Patch introduces new amradio_set_stereo function.
Driver calls this func to make stereo radio reception.
Corrects checking of returned value after usb_bulk_msg.

Signed-off-by: Alexey Klimov <klimov.linux@gmail.com>
Signed-off-by: Douglas Schilling Landgraf <dougsland@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

V4L/DVB (10459): radio-mr800: fix amradio_set_freq

Fixing frequency adjustment to provide better diapason(band?) fit.
Also, add AMRADIO_SET_FREQ to the list of commands.

Signed-off-by: Alexey Klimov <klimov.linux@gmail.com>
Signed-off-by: Douglas Schilling Landgraf <dougsland@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

V4L/DVB (10458): radio-mr800: move radio start and stop in one function

Patch introduces new amradio_set_mute function. Amradio_start and
amradio_stop removed. This makes driver more flexible and it's useful
for next changes.

Signed-off-by: Alexey Klimov <klimov.linux@gmail.com>
Signed-off-by: Douglas Schilling Landgraf <dougsland@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

V4L/DVB (10457): radio-mr800: add more dev_err messages in probe

Patch adds 3 dev_err messages in usb_amradio_probe() function.

Signed-off-by: Alexey Klimov <klimov.linux@gmail.com>
Signed-off-by: Douglas Schilling Landgraf <dougsland@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

V4L/DVB (10456): radio-mr800: place dev_err instead of dev_warn

There should be dev_err message if video_register_device() fails.
Correct this situation.

Signed-off-by: Alexey Klimov <klimov.linux@gmail.com>
Signed-off-by: Douglas Schilling Landgraf <dougsland@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

V4L/DVB (10455): radio-mr800: codingstyle cleanups

Cleanups of many if-check constructions.

Signed-off-by: Alexey Klimov <klimov.linux@gmail.com>
Signed-off-by: Douglas Schilling Landgraf <dougsland@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

V4L/DVB (10453): af9015: add MC44S803 support

Add MC44S803 support to AF9015 driver.

Signed-off-by: Jochen Friedrich <jochen@scram.de>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

V4L/DVB (10452): Add Freescale MC44S803 tuner driver

Add Freescale MC44S803 tuner driver.

Signed-off-by: Jochen Friedrich <jochen@scram.de>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

V4L/DVB (10446): cx18: Finally get sliced VBI working - for 525 line 60 Hz systems at least

Sliced VBI, in the manner that ivtv implements it as a separate data stream,
now works for 525 line 60 Hz systems like NTSC-M.  It may work for 625 line
50 Hz systems, but I have more engineering work to do, to verify it is operating
properly.  Sliced data insertion into the MPEG PS should be working, but is
untested.

Signed-off-by: Andy Walls <awalls@radix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

V4L/DVB (10445): cx18: Process Raw VBI on a whole frame basis; fix VBI buffer size

The cx23418 appears to send Raw VBI buffers with a PTS on a per frame
basis, not per field, so process Raw VBI on a whole frame basis and reduce
some complexity.  Fix VBI buffer size computation to handle a whole
frame of Raw VBI for a 625 line system, which is the worst case and will
work for 525 lines systems as well.

Signed-off-by: Andy Walls <awalls@radix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

V4L/DVB (10444): cx18: Fix sliced VBI PTS and fix artifacts in last raw line of field

Fixed an endianess problem with the collection of the PTS from
the VBI buffer given to us by the encoder.  Also extrapolated the
last 12 bytes of the last line of each field, to remove artifacts
created by removing the first 12 bytes of each field for raw VBI.

Signed-off-by: Andy Walls <awalls@radix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

V4L/DVB (10443): cx18: Use correct line counts per field in firmware API call

The driver was incorrectly setting 0 line counts in a firmware
API call to set the maximum amount of lines per field.

Signed-off-by: Andy Walls <awalls@radix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

V4L/DVB (10442): cx18: Fixes for enforcing when Encoder Raw VBI params can be set

The Encoder will only allow the Raw VBI parameters, along with a number of
other API parameters, to take effect when no analog captures are in
progress.  These parameters must be set before the first analog capture starts,
be it MPEG, VBI, YUV, etc., and cannot be changed until the last one stops.  It
is not obvious to me what capture channel API parameters are shared and which
ones must be set per capture channel, so set them all for every analog
capture channel start up.  This fixes the driver so that VBI capture can be
started up after the MPEG capture is going.

Signed-off-by: Andy Walls <awalls@radix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

V4L/DVB (10441): cx18: Fix VBI ioctl() handling and Raw/Sliced VBI state management

More sliced VBI fixes to bring the cx18 driver closer to full V4L2 spec
compliance for VBI and to get sliced VBI working better.

Signed-off-by: Andy Walls <awalls@radix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

V4L/DVB (10440): cx18: Fix presentation timestamp (PTS) for VBI buffers

The old code from ivtv used a CX23415/6 PTS, which was simply left at 0 in the
cx18 driver.  Since the CX23418 gives us what I think is a PTS (or some other
90 kHz clock count) with each VBI buffer, this change has the cx18 driver use
that as a PTS.

Signed-off-by: Andy Walls <awalls@radix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

V4L/DVB (10439): cx18: Clean-up and enable sliced VBI handling

Removed legacy ivtv state variables, added comments, and cleaned
up sliced VBI related code.  Enabled sliced VBI.

Signed-off-by: Andy Walls <awalls@radix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

V4L/DVB (10437): cx18: Remove an unused spinlock

Signed-off-by: Andy Walls <awalls@radix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

V4L/DVB (10436): cx18: Fix coding style of a switch statement per checkpatch.pl

Signed-off-by: Andy Walls <awalls@radix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

V4L/DVB (10435): cx18: Normalize APU after second APU firmware load

Signed-off-by: Andy Walls <awalls@radix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

V4L/DVB (10434): cx18: Smarter verification of CX18_AUDIO_ENABLE register writes

The CX18_AUDIO_ENABLE register usually never reads back what was just written
under normal circumstances.  Perform better checking that a write went to the
register as expected with a specification of what bits to verify.

Signed-off-by: Andy Walls <awalls@radix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

V4L/DVB (10433): cx18: Defer A/V core initialization until a valid cx18_av_cmd arrives

Signed-off-by: Andy Walls <awalls@radix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

V4L/DVB (10432): gspca - vc032x: Cleanup source, optimize and check i2c_write.

Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

V4L/DVB (10431): gspca - vc032x: Bad revision for the webcam 041e:405b.

Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

V4L/DVB (10430): gspca - sonixj: Adjust some exchanges with the sensor mt9v111.

This patch also enables the autogain for the mt9v111.

Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

V4L/DVB (10429): gspca - sonixj: Simplify the probe of the sensors mi0360/mt9v111.

Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

V4L/DVB (10428): gspca - sonixj: Specific gamma tables per sensor.

Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

V4L/DVB (10427): gspca - sonixj: Sensor sp80708 added for webcam 0c45:6143.

Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

V4L/DVB (10425): gspca - sonixj: Bad initialization of sensor mt9v111.

Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

V4L/DVB (10424): gspca - vc032x: Add resolution 1280x1024 for sensor mi1310_soc.

Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

V4L/DVB (10423): gspca - sonixj: Bad sensor definition of the webcams 0c45:60c0.

Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

V4L/DVB (10421): gspca - documentation: Add the webcam 041e:405b.

Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

V4L/DVB (10420): gspca - vc032x: Webcam 041e:405b added and mi1310_soc updated.

The mi1310_soc sequences come from the ms-win driver C0130Dev.inf.

Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

V4L/DVB (10419): gspca - sonixj: Sensor mt9v111 added.

Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

V4L/DVB (10417): sms1xxx: add missing usb id 2040:2011

Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

V4L/DVB (10416): tveeprom: update to include Hauppauge tuners 151-155

Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

V4L/DVB (10415): dib0700: add data debug to dib0700_i2c_xfer_new

Data debug for i2c transactions was provided by the functions
called by dib0700_i2c_xfer_legacy, but not dib0700_i2c_xfer_new.

This patch adds the missing data debug dumps to dib0700_i2c_xfer_new.

Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

V4L/DVB (10413): Bug fix: Restore HVR-4000 tuning.

Some cards uses cx24116 LNB_DC pin for LNB power control,
some not uses, some uses it different way, like HVR-4000.

Tested-by : Edgar Hucek <gimli@dark-green.com>

Signed-off-by: Igor M. Liplianin <liplianin@me.by>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

V4L/DVB (10409): v4l: remove unused I2C_DRIVERIDs.

I2C_DRIVERIDs are phased out. Remove those that are unused at the moment.

Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

V4L/DVB (10408): v4l2: fix incorrect hue range check

A hue of -128 was rejected due to an incorrect range check, which was
faithfully copy-and-pasted into four drivers...

Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

V4L/DVB (10406): gspca: fix compiler warning

Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

V4L/DVB (10405): saa7134-core: loading saa7134-alsa is now the default

Most boards nowadays supports saa7134-alsa. Even some of they doesn't have any
option to wire an audio cable. So, lets load saa7134-alsa by default, if the
board is not based on saa7130 and if saa7134-alsa is compiled.

Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

V4L/DVB (10404): saa7134-core: remove oss option, since saa7134-oss doesn't exist anymore

Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

V4L/DVB (10394): KWorld ATSC 115 all static

saa7134: Fix tuner access on Kworld ATSC110

--
To unsubscribe from this list: send the line "unsubscribe linux-media" in
the body of a message to majordomo@vger.kernel.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html

Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

V4L/DVB (10392): lnbp21: documentation about the system register

Here is a patch which adds some documentation about meanings of the
the lnbp21 system register bits.

Signed-off-by: Hans Werner <hwerner4@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

V4L/DVB (10391): dvb: constify VFTs

dvb: constify VFTs

Signed-off-by: Jan Engelhardt <jengelh@medozas.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

V4L/DVB (10389): gspca - zc3xx: Do work the sensor adcm2700.

The lack of the green color is fixed by sensor sequences closer to the
ms-win traces.

Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

V4L/DVB (10388): gspca - pac207: Webcam 093a:2474 added.

Signed-off-by: Lierdakil <root@livid.pp.ru>
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

V4L/DVB (10387): gspca - spca505: Move some sequences from probe to streamon.

The webcams worked only one time after connection.

Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

V4L/DVB (10384): gspca - spca505: Simplify and add the brightness in start.

Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

V4L/DVB (10383): gspca - spca505: Cleanup and optimize code.

Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

V4L/DVB (10382): gspca - t613: Bad returned value when no known sensor found.

Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

V4L/DVB (10381): gspca - t613: New unknown sensor added.

Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

V4L/DVB (10380): gspca - t613: Cleanup and optimize code.

Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

V4L/DVB (10379): gspca - main: Use usb_make_path() for VIDIOC_QUERYCAP.

Signed-off-by: Thierry MERLE <thierry.merle@free.fr>
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

V4L/DVB (10378): gspca - main: Avoid error on set interface on disconnection.

Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

V4L/DVB (10376): gspca - zc3xx: Remove some useless tables of sensor adcm2700.

Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

V4L/DVB (10375): gspca - zc3xx: Remove duplicated sequence of sensor cs2102k.

Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

V4L/DVB (10374): gspca - zc3xx: Bad probe of the sensor adcm2700.

Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

V4L/DVB (10373): gspca - zc3xx: Sensor adcm2700 added.

Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

V4L/DVB (10372): gspca - sonixj: Cleanup code.

Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

V4L/DVB (10371): gspca - spca561: Fix image problem in the 352x288 mode of rev72a.

With the wrong clock value, the image had two moving colored lines.

Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

V4L/DVB (10370): gspca - main: Have 3 URBs instead of 2 for ISOC transfers.

Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

V4L/DVB (10369): gspca - mr97310a: Fix camera initialization copy/paste bugs.

Signed-off-by: Kyle Guinn <elyk03@gmail.com>
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

V4L/DVB (10368): gspca - spca561: Fix bugs and rewrite the init/start of the rev72a.

The bugs were in the first init sequence of the sensor.
The rewrite is adapted from a ms-win trace.

Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

V4L/DVB (10367): gspca - spca561: Optimize the isoc scanning function.

Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

V4L/DVB (10366): gspca - mr97310a: New subdriver.

This patch adds support for USB webcams based on the MR97310A chip. It was
tested with an Aiptek PenCam VGA+ webcam.

Signed-off-by: Kyle Guinn <elyk03@gmail.com>
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

V4L/DVB (10365): Add Mars-Semi MR97310A format

The MR97310A is a dual-mode webcam controller that provides compressed BGGR
Bayer frames.  The decompression algorithm for still images is the same as for
video, and is currently implemented in libgphoto2.

Signed-off-by: Kyle Guinn <elyk03@gmail.com>
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

V4L/DVB (10363): gspca - spca500: Abnormal error message when starting ClickSmart310.

Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

V4L/DVB (10361): gspca - sonixj: Gamma control added.

Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

V4L/DVB (10360): gspca - mars: Bad interface/altsetting since 0a10a0e906be.

Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

V4L/DVB (10357): gspca - main: Cleanup code.

Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

V4L/DVB (10356): gspca - sonixj: Cleanup code.

Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

V4L/DVB (10354): gspca - tv8532: Change the max brightness.

Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

V4L/DVB (10353): gspca - some subdrivers: Don't get the control values from the webcam.

Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

V4L/DVB (10352): gspca - spca508: Cleanup code.

Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>