ASoC: SOF: fix an Oops, caused by invalid topology

It is possible to create invalid topology that will cause a kernel
Oops when trying to allocate buffers for a NULL substream.
Specifically such an Oops was caused by a topology, where a DAI on a
capture pipeline was referencing the PCM ID from a playback pipeline.
Fix the Oops by explicitly checking for NULL.

Signed-off-by: Guennadi Liakhovetski <guennadi.liakhovetski@linux.intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20200124213625.30186-2-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>

ASoC: amd: Fix for Subsequent Playback issue.

If we play audio back to back, which kills one playback
and immediately start another, we can hear clicks.
This patch fixes the issue.

Signed-off-by: Ravulapati Vishnu vardhan rao <Vishnuvardhanrao.Ravulapati@amd.com>
Link: https://lore.kernel.org/r/1580124397-19842-1-git-send-email-Vishnuvardhanrao.Ravulapati@amd.com
Signed-off-by: Mark Brown <broonie@kernel.org>

ASoC: SOF: Intel: do not disable i915 power during probe

Change HDA probe behaviour slightly so that i915 power is not
turned off if i915 audio codecs are found in the initial probe done
by SOF Intel driver, and power is kept on until HDA codec driver
probe runs.

This will reduce number of mode sets on platforms with low
minimum CDCLK (like GLK) and brings the SOF probe sequence closer
to legacy HDA driver in terms of i915 audio codec power management.

BugLink: https://github.com/thesofproject/linux/issues/1642
Signed-off-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Link: https://lore.kernel.org/r/20200120160117.29130-3-kai.vehmanen@linux.intel.com
Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

ASoC: SOF: Intel: refactor i915_get/put functions

The current interface to control i915 display power is misleading.
The hda_codec_i915_get() and hda_codec_i915_put() names suggest
a refcounting based interface. This is confusing as no refcounting
is done and the underlying HDAC library interface does not support
refcounts eithers.

Clarify the code by replacing the functions with a single
hda_codec_i915_display_power() that is aligned with
snd_hdac_display_power().

Signed-off-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Link: https://lore.kernel.org/r/20200120160117.29130-2-kai.vehmanen@linux.intel.com
Acked-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

ASoC: rt1015: Remove unnecessary const

Clang warns:

../sound/soc/codecs/rt1015.c:392:14: warning: duplicate 'const'
declaration specifier [-Wduplicate-decl-specifier]
static const SOC_ENUM_SINGLE_DECL(rt1015_boost_mode_enum, 0, 0,
             ^
../include/sound/soc.h:355:2: note: expanded from macro
'SOC_ENUM_SINGLE_DECL'
        SOC_ENUM_DOUBLE_DECL(name, xreg, xshift, xshift, xtexts)
        ^
../include/sound/soc.h:352:2: note: expanded from macro
'SOC_ENUM_DOUBLE_DECL'
        const struct soc_enum name = SOC_ENUM_DOUBLE(xreg, xshift_l, xshift_r, \
        ^
1 warning generated.

Remove the const after static to fix it.

Fixes: df31007400c3 ("ASoC: rt1015: add rt1015 amplifier driver")
Link: https://github.com/ClangBuiltLinux/linux/issues/845
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Link: https://lore.kernel.org/r/20200124155750.33753-1-natechancellor@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>

ASoC: max98090: silence lockdep warning

Commit 08df0d9a00f7 ("ASoC: max98090: revert "ASoC: max98090: fix lockdep
warning"") provided a good rationale for removing separate lock for the
SHDN register access. However it restored the lockdep warning during the
system boot. To silence the lockdep warning, mark the mutex taken in the
max98090_shdn_save() function with the lockdep class dedicated for the
runtime DAPM operations: SND_SOC_DAPM_CLASS_RUNTIME. This finally fixes
the following lockdep warning observed on Exynos4412-based Odroid U3
board:

======================================================
WARNING: possible circular locking dependency detected
5.5.0-rc7-next-20200123 #7329 Not tainted
------------------------------------------------------
alsactl/1105 is trying to acquire lock:
ed4f7cf4 (&card->dapm_mutex){+.+.}, at: max98090_shdn_save+0x1c/0x28

but task is already holding lock:
edb8d49c (&card->controls_rwsem){++++}, at: snd_ctl_ioctl+0xcc/0xbb8

which lock already depends on the new lock.

the existing dependency chain (in reverse order) is:

-> #1 (&card->controls_rwsem){++++}:
       snd_ctl_add_replace+0x3c/0x84
       dapm_create_or_share_kcontrol+0x24c/0x2e0
       snd_soc_dapm_new_widgets+0x308/0x594
       snd_soc_bind_card+0x834/0xa94
       devm_snd_soc_register_card+0x34/0x6c
       odroid_audio_probe+0x288/0x34c
       platform_drv_probe+0x6c/0xa4
       really_probe+0x200/0x48c
       driver_probe_device+0x78/0x1f8
       bus_for_each_drv+0x74/0xb8
       __device_attach+0xd4/0x16c
       bus_probe_device+0x88/0x90
       deferred_probe_work_func+0x3c/0xd0
       process_one_work+0x230/0x7bc
       worker_thread+0x44/0x524
       kthread+0x130/0x164
       ret_from_fork+0x14/0x20
       0x0

-> #0 (&card->dapm_mutex){+.+.}:
       lock_acquire+0xe8/0x270
       __mutex_lock+0x9c/0xb18
       mutex_lock_nested+0x1c/0x24
       max98090_shdn_save+0x1c/0x28
       max98090_put_enum_double+0x20/0x40
       snd_ctl_ioctl+0x190/0xbb8
       ksys_ioctl+0x484/0xb10
       ret_fast_syscall+0x0/0x28
       0xbede0564

other info that might help us debug this:

 Possible unsafe locking scenario:

       CPU0                    CPU1
       ----                    ----
  lock(&card->controls_rwsem);
                               lock(&card->dapm_mutex);
                               lock(&card->controls_rwsem);
  lock(&card->dapm_mutex);

 *** DEADLOCK ***

1 lock held by alsactl/1105:
 #0: edb8d49c (&card->controls_rwsem){++++}, at: snd_ctl_ioctl+0xcc/0xbb8

stack backtrace:
CPU: 2 PID: 1105 Comm: alsactl Not tainted 5.5.0-rc7-next-20200123 #7329
Hardware name: Samsung Exynos (Flattened Device Tree)
[<c01126f0>] (unwind_backtrace) from [<c010e1e8>] (show_stack+0x10/0x14)
[<c010e1e8>] (show_stack) from [<c0b5234c>] (dump_stack+0xb4/0xe0)
[<c0b5234c>] (dump_stack) from [<c018a610>] (check_noncircular+0x1ec/0x208)
[<c018a610>] (check_noncircular) from [<c018ca2c>] (__lock_acquire+0x1210/0x25ec)
[<c018ca2c>] (__lock_acquire) from [<c018e728>] (lock_acquire+0xe8/0x270)
[<c018e728>] (lock_acquire) from [<c0b71928>] (__mutex_lock+0x9c/0xb18)
[<c0b71928>] (__mutex_lock) from [<c0b723c0>] (mutex_lock_nested+0x1c/0x24)
[<c0b723c0>] (mutex_lock_nested) from [<c086097c>] (max98090_shdn_save+0x1c/0x28)
[<c086097c>] (max98090_shdn_save) from [<c08613f8>] (max98090_put_enum_double+0x20/0x40)
[<c08613f8>] (max98090_put_enum_double) from [<c0833f20>] (snd_ctl_ioctl+0x190/0xbb8)
[<c0833f20>] (snd_ctl_ioctl) from [<c02cae14>] (ksys_ioctl+0x484/0xb10)
[<c02cae14>] (ksys_ioctl) from [<c0101000>] (ret_fast_syscall+0x0/0x28)
Exception stack(0xed331fa8 to 0xed331ff0)
...

Fixes: 08df0d9a00f7 ("ASoC: max98090: revert "ASoC: max98090: fix lockdep warning"")
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Tzung-Bi Shih <tzungbi@google.com>
Link: https://lore.kernel.org/r/20200123134046.9769-1-m.szyprowski@samsung.com
Signed-off-by: Mark Brown <broonie@kernel.org>

ASoC: soc-core: remove null_snd_soc_ops

All rtd->dai_link callback functions are controlled by soc_rtd_xxxx(),
and checking rtd->dai_link->ops.
We don't need to have null_snd_soc_ops anymore.
This patch removes it.

Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://lore.kernel.org/r/87zhegl3oz.wl-kuninori.morimoto.gx@renesas.com
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

ASoC: soc-pcm: add soc_rtd_trigger()

Add soc_rtd_trigger() to make the code easier to read

Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://lore.kernel.org/r/871rrsmi9j.wl-kuninori.morimoto.gx@renesas.com
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

ASoC: soc-pcm: add soc_rtd_hw_free()

Add soc_rtd_hw_free() to make the code easier to read

Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://lore.kernel.org/r/8736c8mi9n.wl-kuninori.morimoto.gx@renesas.com
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

ASoC: soc-pcm: add soc_rtd_hw_params()

Add soc_rtd_hw_params() to make the code easier to read

Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://lore.kernel.org/r/874kwomi9r.wl-kuninori.morimoto.gx@renesas.com
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

ASoC: soc-pcm: add soc_rtd_prepare()

Add soc_rtd_prepare() to make the code easier to read

Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://lore.kernel.org/r/875zh4mi9v.wl-kuninori.morimoto.gx@renesas.com
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

ASoC: soc-pcm: add soc_rtd_shutdown()

Add soc_rtd_shutdown() to make the code easier to read

Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://lore.kernel.org/r/877e1kmi9z.wl-kuninori.morimoto.gx@renesas.com
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

ASoC: soc-pcm: add soc_rtd_startup()

Add soc_rtd_startup() to make the code easier to read

Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://lore.kernel.org/r/878sm0mia4.wl-kuninori.morimoto.gx@renesas.com
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

ASoC: rt1015: add rt1015 amplifier driver

This is initial amplifier driver for rt1015.

Signed-off-by: Jack Yu <jack.yu@realtek.com>
Link: https://lore.kernel.org/r/20200115112519.22050-1-jack.yu@realtek.com
Signed-off-by: Mark Brown <broonie@kernel.org>

ASoC: madera: Correct some kernel doc

Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20200122104559.17043-1-ckeepax@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>

ASoC: Add MediaTek MT6660 Speaker Amp Driver

The MT6660 is a boosted BTL class-D amplifier with V/I sensing.
A built-in DC-DC step-up converter is used to provide efficient
power for class-D amplifier with multi-level class-G operation.
The digital audio interface supports I2S, left-justified,
right-justified, TDM and DSP A/B format for audio in with a data
out used for chip information like voltage sense and current
sense, which are able to be monitored via DATAO through proper

Signed-off-by: Jeff Chang <jeff_chang@richtek.com>
Link: https://lore.kernel.org/r/1579153597-23286-1-git-send-email-richtek.jeff.chang@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>

ASoC: dt-bindings: rt5645: add suppliers

The rt5645 and rt5650 have two suppliers, document them.

Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Link: https://lore.kernel.org/r/20200114150151.8537-1-matthias.bgg@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>

ASoC: max98090: fix deadlock in max98090_dapm_put_enum_double()

Commit 62d5ae4cafb7 ("ASoC: max98090: save and restore SHDN when
changing sensitive registers SHDN bit") uses dapm_mutex to protect SHDN
bit.  However, snd_soc_dapm_put_enum_double() in
max98090_dapm_put_enum_double() acquires the dapm_mutex again which
cause a deadlock.

Use snd_soc_dapm_put_enum_double_locked() instead to fix the deadlock.

Fixes: 62d5ae4cafb7 ("ASoC: max98090: save and restore SHDN when changing sensitive registers SHDN bit")
Signed-off-by: Tzung-Bi Shih <tzungbi@google.com>
Link: https://lore.kernel.org/r/20200117073814.82441-4-tzungbi@google.com
Signed-off-by: Mark Brown <broonie@kernel.org>

ASoC: dapm: add snd_soc_dapm_put_enum_double_locked

Adds snd_soc_dapm_put_enum_double_locked() for those use cases if
dapm_mutex has already locked.

Signed-off-by: Tzung-Bi Shih <tzungbi@google.com>
Link: https://lore.kernel.org/r/20200117073814.82441-3-tzungbi@google.com
Signed-off-by: Mark Brown <broonie@kernel.org>

ASoC: max98090: revert "ASoC: max98090: fix lockdep warning"

Commit 2dc98af62c32 ("ASoC: max98090: fix lockdep warning") introduced
a helpful-less small lock: shdn_lock.  Reverts the commit.

Reasons:

1. Lockdep should not be happy by either the original or current code.
From lockdep's point of view, there is a lock inversion anyway.

Let d = dapm_mutex, c = controls_rwsem, s = shdn_lock,

From the reported calling stack: lock acquisition order of
snd_soc_register_card() is: d -> c.
> snd_ctl_add_replace+0x3c/0x84
> dapm_create_or_share_kcontrol+0x24c/0x2e0
> snd_soc_dapm_new_widgets+0x308/0x594
> snd_soc_bind_card+0x80c/0xad4
> devm_snd_soc_register_card+0x34/0x6c

If calling snd_soc_dapm_put_enum_double() in kcontrol's put (e.g.
SOC_DAPM_ENUM_EXT), lock acquisition order is: c -> d.  Note that,
snd_soc_dapm_put_enum_double() acquires d.

The possible lock inversion is always there if registering sound card
and putting mixer control happen at the same time.  In fact, it never
happens because the control device don't show up to the userspace until
the sound card build success.

Commit 2dc98af62c32 ("ASoC: max98090: fix lockdep warning") changes the
order to: c -> s -> d.  The lock inversion is still there.

2. Commit 62d5ae4cafb7 ("ASoC: max98090: save and restore SHDN when
changing sensitive registers SHDN bit") designed to use dapm_mutex to
protect SHDN bit.  Use a separate lock breaks the protection.

DAPM changes SHDN bit automatically when it finds the path.  Thus, any
code wants to change the SHDN bit, need to acquire the dapm_mutex first.

> SND_SOC_DAPM_SUPPLY("SHDN", M98090_REG_DEVICE_SHUTDOWN,
>        M98090_SHDNN_SHIFT, 0, NULL, 0),

Fixes: 2dc98af62c32 ("ASoC: max98090: fix lockdep warning")
Signed-off-by: Tzung-Bi Shih <tzungbi@google.com>
Link: https://lore.kernel.org/r/20200117073814.82441-2-tzungbi@google.com
Signed-off-by: Mark Brown <broonie@kernel.org>

ASoC: soc-core: remove bus_control

Now, snd_soc_dai_driver::bus_control is used for how to resume.
But, no driver which has bus_control has DAI driver suspend/resume
support.
This patch removes pointless bus_control from ALSA SoC.

Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://lore.kernel.org/r/87pnffx7i4.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>

ASoC: soc-core: remove DAI suspend/resume

Historically, CPU and Codec were implemented different, but now it is
merged as Component.
ALSA SoC is supporting suspend/resume at DAI and Component level.
The method is like below.

1) Suspend/Resume all CPU DAI if bus-control was 0
2) Suspend/Resume all Component
3) Suspend/Resume all CPU DAI if bus-control was 1

Historically 2) was Codec special operation.
Because CPU and Codec were merged into Component,
CPU   suspend/resume has 3 chance to suspend(= 1/2/3), but
Codec suspend/resume has 1 chance (= 2).

Here, DAI side suspend/resume is caring bus-control, but no driver
which is supporting suspend/resume is setting bus-control.
This means 3) was never used.

Here, used parameter for suspend/resume component->dev and dai->dev are
same pointer.
For that reason, we can merge DAI and Component suspend/resume.
One note is that we should use 2), because it is caring BIAS level.

This patch removes 1) and 3).

Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://lore.kernel.org/r/87r1zvx7i8.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>

ASoC: pxa: pxa2xx-i2s: move .suspend/.resume to component

There is no big difference at implementation for .suspend/.resume
between DAI driver and Component driver.
But because some driver is using DAI version, thus ALSA SoC needs
to keep supporting it, hence, framework becoming verbose.
If we can switch all DAI driver .suspend/.resume to Component driver,
we can remove verbose code from ALSA SoC.

Driver is getting its private data via dai->dev.
But dai->dev and component->dev are same dev, thus, we can convert
these. For same reason, we can convert dai->active to
component->active if necessary.

Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://lore.kernel.org/r/87sgkbx7ic.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>

ASoC: pxa: pxa-ssp: move .suspend/.resume to component

There is no big difference at implementation for .suspend/.resume
between DAI driver and Component driver.
But because some driver is using DAI version, thus ALSA SoC needs
to keep supporting it, hence, framework becoming verbose.
If we can swtcih all DAI driver .suspend/.resume to Component driver,
we can remove verbose code from ALSA SoC.

Driver is getting its private data via dai->dev.
But dai->dev and component->dev are same dev, thus, we can convert
these. For same reason, we can convert dai->active to
component->active if necessary.

This patch moves DAI driver .suspend/.resume to Component driver

Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://lore.kernel.org/r/87tv4rx7ij.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>

ASoC: ux500: ux500_msp_dai: remove unused DAI .suspend/.resume

This patch removes unused DAI driver .suspend/.resume

Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://lore.kernel.org/r/87v9p7x7io.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>

ASoC: samsung: i2s: move .suspend/.resume to component

There is no big difference at implementation for .suspend/.resume
between DAI driver and Component driver.
But because some driver is using DAI version, thus ALSA SoC needs
to keep supporting it, hence, framework becoming verbose.
If we can switch all DAI driver .suspend/.resume to Component driver,
we can remove verbose code from ALSA SoC.

Driver is getting its private data via dai->dev.
But dai->dev and component->dev are same dev, thus, we can convert
these. For same reason, we can convert dai->active to
component->active if necessary.

This patch moves DAI driver .suspend/.resume to Component driver

Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://lore.kernel.org/r/87wo9nx7it.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>

ASoC: dwc: dwc-i2s: move .suspend/.resume to component

There is no big difference at implementation for .suspend/.resume
between DAI driver and Component driver.
But because some driver is using DAI version, thus ALSA SoC needs
to keep supporting it, hence, framework becoming verbose.
If we can switch all DAI driver .suspend/.resume to Component driver,
we can remove verbose code from ALSA SoC.

Driver is getting its private data via dai->dev.
But dai->dev and component->dev are same dev, thus, we can convert
these. For same reason, we can convert dai->active to
component->active if necessary.

This patch moves DAI driver .suspend/.resume to Component driver

Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://lore.kernel.org/r/87y2u3x7iy.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>

ASoC: uniphier: move .suspend/.resume to component

There is no big difference at implementation for .suspend/.resume
between DAI driver and Component driver.
But because some driver is using DAI version, thus ALSA SoC needs
to keep supporting it, hence, framework becoming verbose.
If we can switch all DAI driver .suspend/.resume to Component driver,
we can remove verbose code from ALSA SoC.

Driver is getting its private data via dai->dev.
But dai->dev and component->dev are same dev, thus, we can convert
these. For same reason, we can convert dai->active to
component->active if necessary.

This patch moves DAI driver .suspend/.resume to Component driver

Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://lore.kernel.org/r/87zhejx7j4.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>

ASoC: ti: omap-mcpdm: move .suspend/.resume to component

There is no big difference at implementation for .suspend/.resume
between DAI driver and Component driver.
But because some driver is using DAI version, thus ALSA SoC needs
to keep supporting it, hence, framework becoming verbose.
If we can switch all DAI driver .suspend/.resume to Component driver,
we can remove verbose code from ALSA SoC.

Driver is getting its private data via dai->dev.
But dai->dev and component->dev are same dev, thus, we can convert
these. For same reason, we can convert dai->active to
component->active if necessary.

This patch moves DAI driver .suspend/.resume to Component driver

Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Link: https://lore.kernel.org/r/871rrvym3p.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>

ASoC: sti: sti_uniperif: move .suspend/.resume to component

There is no big difference at implementation for .suspend/.resume
between DAI driver and Component driver.
But because some driver is using DAI version, thus ALSA SoC needs
to keep supporting it, hence, framework becoming verbose.
If we can switch all DAI driver .suspend/.resume to Component driver,
we can remove verbose code from ALSA SoC.

Driver is getting its private data via dai->dev.
But dai->dev and component->dev are same dev, thus, we can convert
these. For same reason, we can convert dai->active to
component->active if necessary.

This patch moves DAI driver .suspend/.resume to Component driver

Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://lore.kernel.org/r/8736cbym3x.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>

ASoC: samsung: spdif: move .suspend/.resume to component

There is no big difference at implementation for .suspend/.resume
between DAI driver and Component driver.
But because some driver is using DAI version, thus ALSA SoC needs
to keep supporting it, hence, framework becoming verbose.
If we can switch all DAI driver .suspend/.resume to Component driver,
we can remove verbose code from ALSA SoC.

Driver is getting its private data via dai->dev.
But dai->dev and component->dev are same dev, thus, we can convert
these. For same reason, we can convert dai->active to
component->active if necessary.

This patch moves DAI driver .suspend/.resume to Component driver

Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://lore.kernel.org/r/874kwrym42.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>

ASoC: samsung: s3c24xx-i2s: move .suspend/.resume to component

There is no big difference at implementation for .suspend/.resume
between DAI driver and Component driver.
But because some driver is using DAI version, thus ALSA SoC needs
to keep supporting it, hence, framework becoming verbose.
If we can switch all DAI driver .suspend/.resume to Component driver,
we can remove verbose code from ALSA SoC.

Driver is getting its private data via dai->dev.
But dai->dev and component->dev are same dev, thus, we can convert
these. For same reason, we can convert dai->active to
component->active if necessary.

This patch moves DAI driver .suspend/.resume to Component driver

Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://lore.kernel.org/r/875zh7ym48.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>

ASoC: mediatek: move .suspend/.resume to component

There is no big difference at implementation for .suspend/.resume
between DAI driver and Component driver.
But because some driver is using DAI version, thus ALSA SoC needs
to keep supporting it, hence, framework becoming verbose.
If we can switch all DAI driver .suspend/.resume to Component driver,
we can remove verbose code from ALSA SoC.

Driver is getting its private data via dai->dev.
But dai->dev and component->dev are same dev, thus, we can convert
these. For same reason, we can convert dai->active to
component->active if necessary.

This patch moves DAI driver .suspend/.resume to Component driver

Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://lore.kernel.org/r/877e1nym4e.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>

ASoC: jz4740: jz4740-i2s: move .suspend/.resume to component

There is no big difference at implementation for .suspend/.resume
between DAI driver and Component driver.
But because some driver is using DAI version, thus ALSA SoC needs
to keep supporting it, hence, framework becoming verbose.
If we can switch all DAI driver .suspend/.resume to Component driver,
we can remove verbose code from ALSA SoC.

Driver is getting its private data via dai->dev.
But dai->dev and component->dev are same dev, thus, we can convert
these. For same reason, we can convert dai->active to
component->active if necessary.

This patch moves DAI driver .suspend/.resume to Component driver

Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://lore.kernel.org/r/878sm3ym4j.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>

ASoC: cirrus: ep93xx-i2s: move .suspend/.resume to component

There is no big difference at implementation for .suspend/.resume
between DAI driver and Component driver.
But because some driver is using DAI version, thus ALSA SoC needs
to keep supporting it, hence, framework becoming verbose.
If we can switch all DAI driver .suspend/.resume to Component driver,
we can remove verbose code from ALSA SoC.

Driver is getting its private data via dai->dev.
But dai->dev and component->dev are same dev, thus, we can convert
these. For same reason, we can convert dai->active to
component->active if necessary.

This patch moves DAI driver .suspend/.resume to Component driver

Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://lore.kernel.org/r/87a76jym4p.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>

ASoC: atmel: atmel_ssc_dai: move .suspend/.resume to component

There is no big difference at implementation for .suspend/.resume
between DAI driver and Component driver.
But because some driver is using DAI version, thus ALSA SoC needs
to keep supporting it, hence, framework becoming verbose.
If we can switch all DAI driver .suspend/.resume to Component driver,
we can remove verbose code from ALSA SoC.

Driver is getting its private data via dai->dev.
But dai->dev and component->dev are same dev, thus, we can convert
these. For same reason, we can convert dai->active to
component->active if necessary.

This patch moves DAI driver .suspend/.resume to Component driver

Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://lore.kernel.org/r/87d0bfym53.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>

ASoC: bcm: cygnus-ssp: move .suspend/.resume to component

There is no big difference at implementation for .suspend/.resume
between DAI driver and Component driver.
But because some driver is using DAI version, thus ALSA SoC needs
to keep supporting it, hence, framework becoming verbose.
If we can switch all DAI driver .suspend/.resume to Component driver,
we can remove verbose code from ALSA SoC.

Driver is getting its private data via dai->dev.
But dai->dev and component->dev are same dev, thus, we can convert
these. For same reason, we can convert dai->active to
component->active if necessary.

This patch moves DAI driver .suspend/.resume to Component driver

Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://lore.kernel.org/r/87blqzym4w.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>

ASoC: Intel: cht_bsw_rt5645: Remove unnecessary string buffers and snprintf calls

The snprintf calls filling cht_rt5645_cpu_dai_name /
cht_rt5645_codec_aif_name always fill them with the same string
("ssp0-port" resp "rt5645-aif2") so instead of keeping these buffers
around and making cpus->dai_name / codecs->dai_name point to this,
simply update the *->dai_name pointers to directly point to a string
constant containing the desired string.

Signed-off-by: Damian van Soelen <dj.vsoelen@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20200115164619.101705-5-hdegoede@redhat.com
Acked-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

ASoC: Intel: bytcr_rt5651: Remove unnecessary string buffers and snprintf calls

The snprintf calls filling byt_rt56*_codec_aif_name/byt_rt56*_cpu_dai_name
always fill them with the same string ("rt56*-aif2" resp. ssp0-port").
So instead of keeping these buffers around and making codecs->dai_name /
cpus->dai_name point to them, simply update the *->dai_name pointers to
directly point to a string constant containing the desired string.

Signed-off-by: Jordy Ubink <jordyubink@hotmail.nl>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20200115164619.101705-4-hdegoede@redhat.com
Acked-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

ASoC: Intel: bytcr_rt5640: Remove unnecessary string buffers and snprintf calls

The snprintf calls filling byt_rt56*_codec_aif_name/byt_rt56*_cpu_dai_name
always fill them with the same string ("rt56*-aif2" resp. ssp0-port").
So instead of keeping these buffers around and making codecs->dai_name /
cpus->dai_name point to them, simply update the *->dai_name pointers to
directly point to a string constant containing the desired string.

Signed-off-by: Nariman Etemadi <narimantos@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20200115164619.101705-3-hdegoede@redhat.com
Acked-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

ASoC: Intel: bytcr_rt5640: Remove code duplication in byt_rt5640_codec_fixup

The 16 and 24 bit paths in byt_rt5640_codec_fixup are mostly identical,
introduce a local bits variable to address the only difference and move
the common bits out of the if ... else ... .

Signed-off-by: Erik Bussing <eabbussing@outlook.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20200115164619.101705-2-hdegoede@redhat.com
Acked-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

ASoC: msm8916-wcd-analog: Add MIC BIAS Internal3

PM8916 has three TX inputs that each have an (optional) internal
RBIAS resistor. MIC BIAS Internal1/2 (for TX1/2) are already supported.
TX3 does not have its own MIC BIAS supply, instead it is also supplied
from MIC_BIAS1.

Now that we have simplified the MIC BIAS Internal* implementation
we can easily add support for it:

Add a MIC BIAS Internal3 supply that enables the internal RBIAS
resistor on TX3, and make sure to also enable the MIC_BIAS1 supply.

Tested-by: Nikita Travkin <nikitos.tr@gmail.com> # longcheer-l8150
Cc: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Reviewed-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Link: https://lore.kernel.org/r/20200114181229.42302-2-stephan@gerhold.net
Signed-off-by: Mark Brown <broonie@kernel.org>

ASoC: msm8916-wcd-analog: Simplify MIC BIAS Internal

At the moment, MIC BIAS Internal* and MIC BIAS External* both reference
the same register, and have a part of their initialization sequence
duplicated.

For example, the sequence for enabling MIC BIAS Internal1 is:
  I1. Enable MIC_BIAS1 supply (MICB_EN bit in CDC_A_MICB_1_EN)
  I2. Enable internal RBIAS (TX1_INT_RBIAS_EN bit in CDC_A_MICB_1_INT_RBIAS)

The sequence for enabling MIC BIAS External1 is:
  E1. Enable MIC_BIAS1 supply (MICB_EN bit in CDC_A_MICB_1_EN)
  (E2. Ideally, make sure internal RBIAS is disabled. However, this should
   not happen in practice because DAPM will disable unused supplies...)

Right now we have:
  SND_SOC_DAPM_SUPPLY("MIC BIAS Internal1", CDC_A_MICB_1_EN, 7, 0, ...) // I1
  SND_SOC_DAPM_SUPPLY("MIC BIAS External1", CDC_A_MICB_1_EN, 7, 0, ...) // E1
and I2 is done in the PM event handler (pm8916_wcd_analog_enable_micbias_int1).

We can simplify this by defining a common DAPM supply for I1/E1 ("MIC_BIAS1"),
and one DAPM supply for I2 ("MIC BIAS Internal1"). Additional DAPM routes
ensure that we also enable the MIC_BIAS1 supply for the internal and external
pull up resistor.

Another advantage of this is that we now disable the internal RBIAS
when it is not needed. This makes it much easier to add support for
MIC BIAS Internal3 as a next step.

Tested-by: Nikita Travkin <nikitos.tr@gmail.com> # longcheer-l8150
Cc: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Reviewed-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Link: https://lore.kernel.org/r/20200114181229.42302-1-stephan@gerhold.net
Signed-off-by: Mark Brown <broonie@kernel.org>

Merge tag 'asoc-fix-v5.5-rc6' into asoc-5.6

ASoC: Fixes for v5.5

This is mostly driver specific fixes, plus an error handling fix
in the core.  There is a rather large diffstat for the stm32 SAI
driver, this is a very large but mostly mechanical update which
wraps every register access in the driver to allow a fix to the
locking which avoids circular locks, the active change is much
smaller and more reasonably sized.

ASoC: amd: Additional DAI for I2S SP instance.

I2S SP instance has separate BCLK and LRCLK for Tx and Rx.
Creating additional DAI for Rx.

Signed-off-by: Ravulapati Vishnu vardhan rao <Vishnuvardhanrao.Ravulapati@amd.com>
Link: https://lore.kernel.org/r/1579261510-12580-1-git-send-email-Vishnuvardhanrao.Ravulapati@amd.com
Signed-off-by: Mark Brown <broonie@kernel.org>

ASoC: rt715: fix return value check in rt715_sdw_probe()

In case of error, the function devm_regmap_init() returns ERR_PTR() and
never returns NULL. The NULL test in the return value check should be
replaced with IS_ERR().

Fixes: d1ede0641b05 ("ASoC: rt715: add RT715 codec driver")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Link: https://lore.kernel.org/r/20200117024149.75515-1-weiyongjun1@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>

ASoC: rt711: fix return value check in rt711_sdw_probe()

In case of error, the function devm_regmap_init() returns ERR_PTR() and
never returns NULL. The NULL test in the return value check should be
replaced with IS_ERR().

Fixes: 320b8b0d13b8 ("ASoC: rt711: add rt711 codec driver")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Link: https://lore.kernel.org/r/20200115143034.94492-1-weiyongjun1@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>

ASoC: rt700: fix return value check in rt700_sdw_probe()

In case of error, the function devm_regmap_init() returns ERR_PTR() and
never returns NULL. The NULL test in the return value check should be
replaced with IS_ERR().

Fixes: 7d2a5f9ae41e ("ASoC: rt700: add rt700 codec driver")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Link: https://lore.kernel.org/r/20200115143027.94364-1-weiyongjun1@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>

ASoC: rt715: remove unused including <linux/version.h>

Remove including <linux/version.h> that don't need it.

Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Link: https://lore.kernel.org/r/20200116021142.149000-1-yuehaibing@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>

ASoC: rt1011: set the different setting for QFN/WLCSP package

The QFN package is a new one.
There is a different initial setting to the chip of QFN and WLCSP package.

Signed-off-by: Shuming Fan <shumingf@realtek.com>
Link: https://lore.kernel.org/r/20200116091854.18095-1-shumingf@realtek.com
Signed-off-by: Mark Brown <broonie@kernel.org>

ASoC: madera: Correct error path handling in madera_out1_demux_put

Should the write to MADERA_OUTPUT_ENABLES_1 fail and out_clamp[0] not be
set an additional error message will be printed. Clear the ret variable
to avoid this.

Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20200114161841.451-3-ckeepax@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>

Merge branch 'topic/equal' of https://git./linux/kernel/git/broonie/regulator into asoc-5.6

regulator fix for "regulator: core: Add regulator_is_equal() helper"

Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Link: https://lore.kernel.org/r/20200115120258.0e535fcb@canb.auug.org.au
Acked-by: Marek Vasut <marex@denx.de>
Signed-off-by: Mark Brown <broonie@kernel.org>

ASoC: sgtl5000: add multi endpoint support

Support multiple endpoints on SGTL5000 codec port when used in
of_graph context.

This patch allows to share the codec port between two CPU DAIs.

Example:

Custom STM32MP157C board uses SGTL5000 audio codec. This codec is
connected to two serial audio interfaces, which are configured
either as rx or tx.

From AsoC point of view the topolgy is the following:
// 2 CPU DAIs (SAI2A/B), 1 Codec (SGTL5000)
Playback: CPU-A-DAI(slave) -> (master)CODEC-DAI/port0
Record:   CPU-B-DAI(slave) <- (master)CODEC-DAI/port0

In the DT two endpoints have to be associated to the codec port:
sgtl5000_port: port {
    sgtl5000_tx_endpoint: endpoint@0 {
    remote-endpoint = <&sai2a_endpoint>;
    };
    sgtl5000_rx_endpoint: endpoint@1 {
    remote-endpoint = <&sai2b_endpoint>;
    };
};

However, when the audio graph card parses the codec nodes, it expects
to find DAI interface indexes matching the endpoints indexes.

The current patch forces the use of DAI id 0 for both endpoints,
which allows to share the codec DAI between the two CPU DAIs
for playback and capture streams respectively.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20191219213219.366073-1-marex@denx.de
Signed-off-by: Mark Brown <broonie@kernel.org>

ASoC: fsl_asrc: Add support for imx8qm & imx8qxp

There are two asrc module in imx8qm & imx8qxp, each module has
different clock configuration, and the DMA type is EDMA.

So in this patch, we define the new clocks, refine the clock map,
and include struct fsl_asrc_soc_data for different soc usage.

The EDMA channel is fixed with each dma request, one dma request
corresponding to one dma channel. So we need to request dma
channel with dma request of asrc module.

Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com>
Acked-by: Nicolin Chen <nicoleotsuka@gmail.com>
Link: https://lore.kernel.org/r/f33dfe3157b5ab200e09ccbf9ab73d31fac6664b.1575452454.git.shengjiu.wang@nxp.com
Signed-off-by: Mark Brown <broonie@kernel.org>

ASoC: dt-bindings: fsl_asrc: add compatible string for imx8qm & imx8qxp

Add compatible string "fsl,imx8qm-asrc" for imx8qm platform,
"fsl,imx8qxp-asrc" for imx8qxp platform.

There are two asrc modules in imx8qm & imx8qxp, the clock mapping is
different for each other, so add new property "fsl,asrc-clk-map"
to distinguish them.

Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com>
Acked-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/b9352edb014c1ee8530c0fd8829c2b044b3da649.1575452454.git.shengjiu.wang@nxp.com
Signed-off-by: Mark Brown <broonie@kernel.org>

ASoC: sgtl5000: Fix VDDA and VDDIO comparison

Comparing the voltage of VDDA and VDDIO to determine whether or not to
enable VDDC manual override is insufficient. This is a problem in case
the VDDA is supplied from different regulator than VDDIO, while both
report the same voltage to the regulator framework. In that case where
VDDA and VDDIO is supplied by different regulators, the VDDC manual
override must not be applied.

Fixes: b6319b061ba2 ("ASoC: sgtl5000: Fix charge pump source assignment")
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Igor Opaniuk <igor.opaniuk@toradex.com>
Cc: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Cc: Mark Brown <broonie@kernel.org>
Cc: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
Link: https://lore.kernel.org/r/20191220164450.1395038-2-marex@denx.de
Signed-off-by: Mark Brown <broonie@kernel.org>

Merge tag 'regulator-eq' of https://git./linux/kernel/git/broonie/regulator into asoc-5.6

regulator: add regulator_equal()

regulator: core: Add regulator_is_equal() helper

Add regulator_is_equal() helper to compare whether two regulators are
the same. This is useful for checking whether two separate regulators
in a driver are actually the same supply.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Igor Opaniuk <igor.opaniuk@toradex.com>
Cc: Liam Girdwood <lgirdwood@gmail.com>
Cc: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Cc: Mark Brown <broonie@kernel.org>
Cc: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
Link: https://lore.kernel.org/r/20191220164450.1395038-1-marex@denx.de
Signed-off-by: Mark Brown <broonie@kernel.org>

ASoC: codecs: Add jz4770-codec driver

Add jz4770-codec driver to support the internal CODEC found in the
JZ4770 SoC from Ingenic.

Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Maarten ter Huurne <maarten@treewalker.org>
Link: https://lore.kernel.org/r/20191224002708.1207884-2-paul@crapouillou.net
Signed-off-by: Mark Brown <broonie@kernel.org>

dt-bindings: sound: Convert jz47*-codec doc to YAML

Convert ingenic,jz4740-codec.txt and ingenic,jz4725b-codec.txt to one
single ingenic,codec.yaml file, since they share the same binding.

Add the ingenic,jz4770-codec compatible string in the process.

Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20191224002708.1207884-1-paul@crapouillou.net
Signed-off-by: Mark Brown <broonie@kernel.org>

ASoC: Intel: bytcr_rt5651: switch to using devm_fwnode_gpiod_get()

devm_fwnode_get_index_gpiod_from_child() is going away as the name is
too unwieldy, let's switch to using the new devm_fwnode_gpiod_get().

Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Link: https://lore.kernel.org/r/20200103011754.GA260926@dtor-ws
Signed-off-by: Mark Brown <broonie@kernel.org>

ASoC: Intel: bytcr_rt5651: remove unused variable

Fix GCC warning with W=1

sound/soc/intel//boards/bytcr_rt5651.c:659:40: warning:
‘byt_rt5651_dai_params’ defined but not used
[-Wunused-const-variable=]

Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20200113210428.27457-19-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>

ASoC: Intel: bytcr_rt5640: remove unused variable

Fix GCC warning with W=1

sound/soc/intel//boards/bytcr_rt5640.c:936:40: warning:
‘byt_rt5640_dai_params’ defined but not used
[-Wunused-const-variable=]

Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20200113210428.27457-18-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>

ASoC: Intel: bytcht_es8316: removed unused variable

fix GCC warning with W=1

sound/soc/intel//boards/bytcht_es8316.c:237:40: warning:
‘byt_cht_es8316_dai_params’ defined but not used
[-Wunused-const-variable=]

Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20200113210428.27457-17-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>

ASoC: Intel: skl_rt286: rename shadowed variable

Fix cppcheck warning:

[sound/soc/intel/boards/skl_rt286.c:171] ->
[sound/soc/intel/boards/skl_rt286.c:214]: (style) Local variable
'channels' shadows outer variable

[sound/soc/intel/boards/skl_rt286.c:171] ->
[sound/soc/intel/boards/skl_rt286.c:250]: (style) Local variable
'channels' shadows outer variable

Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20200113210428.27457-16-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>

ASoC: Intel: skl_nau88l25_ssm4567: rename shadowed variable

Fix cppcheck warning

[sound/soc/intel/boards/skl_nau88l25_ssm4567.c:277] ->
[sound/soc/intel/boards/skl_nau88l25_ssm4567.c:320]: (style) Local
variable 'channels' shadows outer variable

[sound/soc/intel/boards/skl_nau88l25_ssm4567.c:277] ->
[sound/soc/intel/boards/skl_nau88l25_ssm4567.c:337]: (style) Local
variable 'channels' shadows outer variable

Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20200113210428.27457-15-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>

ASoC: Intel: skl_nau88l25_max98357a: rename shadowed variable

Fix cppcheck warning:

[sound/soc/intel/boards/skl_nau88l25_max98357a.c:257] ->
[sound/soc/intel/boards/skl_nau88l25_max98357a.c:142]: (style) Local
variable 'channels' shadows outer variable

[sound/soc/intel/boards/skl_nau88l25_max98357a.c:257] ->
[sound/soc/intel/boards/skl_nau88l25_max98357a.c:318]: (style) Local
variable 'channels' shadows outer variable

Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20200113210428.27457-14-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>

ASOC: Intel: kbl_rt5663_rt5514_max98927: remove useless initialization

Fix cppcheck warning:

[sound/soc/intel/boards/kbl_rt5663_rt5514_max98927.c:764]: (style)
Variable 'ret' is assigned a value that is never used.

Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20200113210428.27457-13-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>

ASoC: Intel: kbl_rt5663_rt5514_max98927: rename shadowed variable

Fix cppcheck warning:

[sound/soc/intel/boards/kbl_rt5663_rt5514_max98927.c:293] ->
[sound/soc/intel/boards/kbl_rt5663_rt5514_max98927.c:336]: (style)
Local variable 'channels' shadows outer variable

Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20200113210428.27457-12-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>

ASoC: Intel: kbl_rt5663_max98927: rename shadowed variable

Fix cppcheck warning:

[sound/soc/intel/boards/kbl_rt5663_max98927.c:358] ->
[sound/soc/intel/boards/kbl_rt5663_max98927.c:401]: (style) Local
variable 'channels' shadows outer variable

[sound/soc/intel/boards/kbl_rt5663_max98927.c:358] ->
[sound/soc/intel/boards/kbl_rt5663_max98927.c:457]: (style) Local
variable 'channels' shadows outer variable

Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20200113210428.27457-11-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>

ASoC: Intel: kbl_rt5660: rename shadowed variable

Fix cppcheck warning:

[sound/soc/intel/boards/kbl_rt5660.c:282] ->
[sound/soc/intel/boards/kbl_rt5660.c:141]: (style) Local variable
'channels' shadows outer variable

Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20200113210428.27457-10-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>

ASoC: Intel: kbl_da7219_max98927: remove unnecessary initialization

Fix cppcheck warning

[sound/soc/intel/boards/kbl_da7219_max98927.c:179]: (style) Variable
'ret' is assigned a value that is never used.

[sound/soc/intel/boards/kbl_da7219_max98927.c:1098]: (style) Variable
'i' is assigned a value that is never used.

Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20200113210428.27457-9-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>

ASoC: Intel: kbl_da7219_max98927: rename shadowed variable

Fix cppcheck warning:

[sound/soc/intel/boards/kbl_da7219_max98927.c:432] ->
[sound/soc/intel/boards/kbl_da7219_max98927.c:282]: (style) Local
variable 'channels' shadows outer variable

[sound/soc/intel/boards/kbl_da7219_max98927.c:432] ->
[sound/soc/intel/boards/kbl_da7219_max98927.c:494]: (style) Local
variable 'channels' shadows outer variable

Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20200113210428.27457-8-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>

ASoC: Intel: kbl_da7219_max98927: test return value on route add

Fix cppcheck warning:

[sound/soc/intel/boards/kbl_da7219_max98927.c:340] ->
[sound/soc/intel/boards/kbl_da7219_max98927.c:348]: (style) Variable
'ret' is reassigned a value before the old one has been used.

Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20200113210428.27457-7-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>

ASoC: Intel: kbl_da7219_max98357a: rename shadowed variable

Fix cppcheck warning:

[sound/soc/intel/boards/kbl_da7219_max98357a.c:257] ->
[sound/soc/intel/boards/kbl_da7219_max98357a.c:144]: (style) Local
variable 'channels' shadows outer variable

[sound/soc/intel/boards/kbl_da7219_max98357a.c:257] ->
[sound/soc/intel/boards/kbl_da7219_max98357a.c:308]: (style) Local
variable 'channels' shadows outer variable

Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20200113210428.27457-6-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>

ASoC: Intel: glk_rt5682_max98357a: removed unused variables

Fix GCC warning with W=1

sound/soc/intel/boards/glk_rt5682_max98357a.c:256:48: warning:
‘constraints_channels’ defined but not used [-Wunused-const-variable=]

Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20200113210428.27457-5-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>

ASoC: Intel: glk_rt5682_max98357a: rename shadowed variable

[sound/soc/intel/boards/glk_rt5682_max98357a.c:252] ->
[sound/soc/intel/boards/glk_rt5682_max98357a.c:121]: (style) Local
variable 'channels' shadows outer variable

[sound/soc/intel/boards/glk_rt5682_max98357a.c:252] ->
[sound/soc/intel/boards/glk_rt5682_max98357a.c:275]: (style) Local
variable 'channels' shadows outer variable

Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20200113210428.27457-4-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>

ASoC: Intel: bxt_rt298: rename shadowed variable

Fix cppcheck warning:

[sound/soc/intel/boards/bxt_rt298.c:291] ->
[sound/soc/intel/boards/bxt_rt298.c:209]: (style) Local variable
'channels' shadows outer variable

[sound/soc/intel/boards/bxt_rt298.c:291] ->
[sound/soc/intel/boards/bxt_rt298.c:258]: (style) Local variable
'channels' shadows outer variable

Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20200113210428.27457-3-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>

ASoC: Intel: bxt_da7219_max98357a: rename shadowed variable

Fix cppcheck warning:

[sound/soc/intel/boards/bxt_da7219_max98357a.c:265] ->
[sound/soc/intel/boards/bxt_da7219_max98357a.c:164]: (style) Local
variable 'channels' shadows outer variable

[sound/soc/intel/boards/bxt_da7219_max98357a.c:265] ->
[sound/soc/intel/boards/bxt_da7219_max98357a.c:316]: (style) Local
variable 'channels' shadows outer variable

Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20200113210428.27457-2-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>

ASoC: SOF: Intel: hda-dai: fix compilation warning in pcm_prepare

Fix GCC warning with W=1, previous cleanup did not remove unnecessary
variable.

sound/soc/sof/intel/hda-dai.c: In function ‘hda_link_pcm_prepare’:

sound/soc/sof/intel/hda-dai.c:265:31: warning: variable ‘hda_stream’
set but not used [-Wunused-but-set-variable]
  265 |  struct sof_intel_hda_stream *hda_stream;
      |                               ^~~~~~~~~~

Fixes: a3ebccb52efdf ("ASoC: SOF: Intel: hda: reset link DMA state in prepare")
Cc: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20200113205620.27285-1-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>

ASoC: rt715: remove warnings

make W=1 reports defined-but-not-used and kernel-doc formatting issues.

No functionality change.

Fixes: d1ede0641b05e4 ("ASoC: rt715: add RT715 codec driver")
Cc: Jack Yu <jack.yu@realtek.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20200113223625.15995-1-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>

ASoC: rt715: use dev_to_sdw_dev() instead of to_sdw_slave_device()

This patch fixup this error

  CC      sound/soc/codecs/rt715-sdw.o
linux/sound/soc/codecs/rt715-sdw.c: In function 'rt715_dev_resume':
linux/sound/soc/codecs/rt715-sdw.c:568:28: error: implicit declaration\
 of function 'to_sdw_slave_device'; did you mean 'sdw_slave_modalias'?\
[-Werror=implicit-function-declaration]
  struct sdw_slave *slave = to_sdw_slave_device(dev);
                            ^~~~~~~~~~~~~~~~~~~
                            sdw_slave_modalias
linux/sound/soc/codecs/rt715-sdw.c:568:28: warning: initialization of\
 'struct sdw_slave *' from 'int' makes pointer from integer without a\
 cast [-Wint-conversion]
cc1: some warnings being treated as errors

Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://lore.kernel.org/r/87h80yhm9p.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>

ASoC: rt700: remove unused including <linux/version.h>

Remove including <linux/version.h> that don't need it.

Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Link: https://lore.kernel.org/r/20200114011319.173401-1-yuehaibing@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>

ASoC: rt1308-sdw: add rt1308 SdW amplifier driver

This is the initial amplifier driver for rt1308-sdw.

Signed-off-by: Shuming Fan <shumingf@realtek.com>
Link: https://lore.kernel.org/r/20200110014606.17333-1-shumingf@realtek.com
Tested-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

ASoC: atmel: fix build error with CONFIG_SND_ATMEL_SOC_DMA=m

If CONFIG_SND_ATMEL_SOC_DMA=m, build error:

sound/soc/atmel/atmel_ssc_dai.o: In function `atmel_ssc_set_audio':
(.text+0x7cd): undefined reference to `atmel_pcm_dma_platform_register'

Function atmel_pcm_dma_platform_register is defined under
CONFIG SND_ATMEL_SOC_DMA, so select SND_ATMEL_SOC_DMA in
CONFIG SND_ATMEL_SOC_SSC, same to CONFIG_SND_ATMEL_SOC_PDC.

Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Chen Zhou <chenzhou10@huawei.com>
Link: https://lore.kernel.org/r/20200113133242.144550-1-chenzhou10@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>

ASoC: msm8916-wcd-digital: Reset RX interpolation path after use

For some reason, attempting to route audio through QDSP6 on MSM8916
causes the RX interpolation path to get "stuck" after playing audio
a few times. In this situation, the analog codec part is still working,
but the RX path in the digital codec stops working, so you only hear
the analog parts powering up. After a reboot everything works again.

So far I was not able to reproduce the problem when using lpass-cpu.

The downstream kernel driver avoids this by resetting the RX
interpolation path after use. In mainline we do something similar
for the TX decimator (LPASS_CDC_CLK_TX_RESET_B1_CTL), but the
interpolator reset (LPASS_CDC_CLK_RX_RESET_CTL) got lost when the
msm8916-wcd driver was split into analog and digital.

Fix this problem by adding the reset to
msm8916_wcd_digital_enable_interpolator().

Fixes: 150db8c5afa1 ("ASoC: codecs: Add msm8916-wcd digital codec")
Cc: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Link: https://lore.kernel.org/r/20200105102753.83108-1-stephan@gerhold.net
Signed-off-by: Mark Brown <broonie@kernel.org>

ASoC: msm8916-wcd-analog: Fix MIC BIAS Internal1

MIC BIAS Internal1 is broken at the moment because we always
enable the internal rbias resistor to the TX2 line (connected to
the headset microphone), rather than enabling the resistor connected
to TX1.

Move the RBIAS code to pm8916_wcd_analog_enable_micbias_int1/2()
to fix this.

Fixes: 585e881e5b9e ("ASoC: codecs: Add msm8916-wcd analog codec")
Cc: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Link: https://lore.kernel.org/r/20200111164006.43074-3-stephan@gerhold.net
Signed-off-by: Mark Brown <broonie@kernel.org>

ASoC: cros_ec_codec: Make the device acpi compatible

Add ACPI entry for cros_ec_codec.

Signed-off-by: Yu-Hsuan Hsu <yuhsuan@chromium.org>
Link: https://lore.kernel.org/r/20200112054900.236576-1-yuhsuan@chromium.org
Signed-off-by: Mark Brown <broonie@kernel.org>

ASoC: sti: fix possible sleep-in-atomic

Change mutex and spinlock management to avoid sleep
in atomic issue.

Signed-off-by: Arnaud Pouliquen <arnaud.pouliquen@st.com>
Link: https://lore.kernel.org/r/20200113100400.30472-1-arnaud.pouliquen@st.com
Signed-off-by: Mark Brown <broonie@kernel.org>

ASoC: msm8916-wcd-analog: Fix selected events for MIC BIAS External1

MIC BIAS External1 sets pm8916_wcd_analog_enable_micbias_ext1()
as event handler, which ends up in pm8916_wcd_analog_enable_micbias_ext().

But pm8916_wcd_analog_enable_micbias_ext() only handles the POST_PMU
event, which is not specified in the event flags for MIC BIAS External1.
This means that the code in the event handler is never actually run.

Set SND_SOC_DAPM_POST_PMU as the only event for the handler to fix this.

Fixes: 585e881e5b9e ("ASoC: codecs: Add msm8916-wcd analog codec")
Cc: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Link: https://lore.kernel.org/r/20200111164006.43074-2-stephan@gerhold.net
Signed-off-by: Mark Brown <broonie@kernel.org>

ASoC: hdac_hda: Fix error in driver removal after failed probe

In case system has multiple HDA codecs, and codec probe fails for
at least one but not all codecs, driver will end up cancelling
a non-initialized timer context upon driver removal.

Call trace of typical case:

[   60.593646] WARNING: CPU: 1 PID: 1147 at kernel/workqueue.c:3032
__flush_work+0x18b/0x1a0
[...]
[   60.593670]  __cancel_work_timer+0x11f/0x1a0
[   60.593673]  hdac_hda_dev_remove+0x25/0x30 [snd_soc_hdac_hda]
[   60.593674]  device_release_driver_internal+0xe0/0x1c0
[   60.593675]  bus_remove_device+0xd6/0x140
[   60.593677]  device_del+0x175/0x3e0
[   60.593679]  ? widget_tree_free.isra.7+0x90/0xb0 [snd_hda_core]
[   60.593680]  snd_hdac_device_unregister+0x34/0x50 [snd_hda_core]
[   60.593682]  snd_hdac_ext_bus_device_remove+0x2a/0x60 [snd_hda_ext_core]
[   60.593684]  hda_dsp_remove+0x26/0x100 [snd_sof_intel_hda_common]
[   60.593686]  snd_sof_device_remove+0x84/0xa0 [snd_sof]
[   60.593687]  sof_pci_remove+0x10/0x30 [snd_sof_pci]
[   60.593689]  pci_device_remove+0x36/0xb0

Signed-off-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20200110235751.3404-9-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>

ASoC: SOF: Intel: fix HDA codec driver probe with multiple controllers

In case system has multiple HDA controllers, it can happen that
same HDA codec driver is used for codecs of multiple controllers.
In this case, SOF may fail to probe the HDA driver and SOF
initialization fails.

SOF HDA code currently relies that a call to request_module() will
also run device matching logic to attach driver to the codec instance.
However if driver for another HDA controller was already loaded and it
already loaded the HDA codec driver, this breaks current logic in SOF.
In this case the request_module() SOF does becomes a no-op and HDA
Codec driver is not attached to the codec instance sitting on the HDA
bus SOF is controlling. Typical scenario would be a system with both
external and internal GPUs, with driver of the external GPU loaded
first.

Fix this by adding similar logic as is used in legacy HDA driver
where an explicit device_attach() call is done after request_module().

Also add logic to propagate errors reported by device_attach() back
to caller. This also works in the case where drivers are not built
as modules.

Signed-off-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20200110235751.3404-8-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>

ASoC: SOF: Intel: lower print level to dbg if we will reinit DSP

We will reinit DSP in a loop when it fails to initialize the first
time, as recommended. So, it is not an error before we finally give
up. And reorder the trace to make it more readable.

Signed-off-by: Bard liao <yung-chuan.liao@linux.intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20200110235751.3404-6-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>

ASoC: SOF: Intel: reference SoundWire machine lists

Use static tables to automatically select the relevant configurations.

Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20200110222530.30303-7-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>

ASoC: Intel: common: add match tables for TGL w/ SoundWire

RT711 is in SoundWire mode on link0.
RT1308 is either on SSP2 or on SoundWire link1 (depending on hardware
reworks).

Signed-off-by: Rander Wang <rander.wang@intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20200110222530.30303-6-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>

ASoC: Intel: common: add match tables for CNL/CFL/CML w/ SoundWire

The two configurations are with the Realtek 3-in-1 board requiring all
4 links to be enabled, or basic configuration with the on-board
RT700 using link1.

For now we only have definitions for CML. CNL and CFL are just
placeholders.

Signed-off-by: Rander Wang <rander.wang@linux.intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20200110222530.30303-5-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>

ASoC: Intel: common: add match tables for ICL w/ SoundWire

The two configurations are with the Realtek 3-in-1 board requiring all
4 links to be enabled, or basic configuration with the on-board RT700
using link0.

Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20200110222530.30303-4-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>

ASoC: Intel: common: soc-acpi: declare new tables for SoundWire

We cannot really lump SoundWire-based configurations into the same
tables since the mechanisms to identify boards is based on link
configurations and _ADR instead of _HID for I2S, so define new tables

Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20200110222530.30303-3-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>

ASoC: soc-acpi: add _ADR-based link descriptors

For SoundWire support, we added a 'link_mask' to describe the PCB hardware
layout. This helped form a signature that can be used as a first-order way
of detecting the hardware and selecting the machine driver.

The concept of link_mask is however not enough. Some BIOS enable all links,
even when there are no devices physically connected. We can also see
variations with multiple devices attached on one link, or different types
of devices connected on the same link. To accurately represent the
hardware, we need to build static tables where each link exposes a list of
expected devices represented by the 64-bit _ADR field (which uniquely
identifies each device).

The new 'links' field is optional when the link_mask is sufficient to
represent a platform in a unique way.

The existing mechanism to support I2C devices is left as is, it'd be too
invasive to change the existing support for _HID and the notion of link is
not relevant either.

Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Bard liao <yung-chuan.liao@linux.intel.com>
Link: https://lore.kernel.org/r/20200110222530.30303-2-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>