realtek: 6.6: copy patch 318-add-rtl83xx-clk-support

Copy the patch file to 6.6

Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>

realtek: 6.6: rework VPE patches

VPE in mainline kernel has changed a lot. This patch wraps up the 5.15
patch files and rebases them in one single patch on top of kernel 6.6.
Former patches are

315-irqchip-irq-realtek-rtl-add-VPE-support.patch
319-irqchip-irq-realtek-rtl-fix-VPE-affinity.patch

Submitted-by: Birger Koblitz <git@birger-koblitz.de>
Submitted-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>

realtek: 6.6: copy VPE patches 315/319

Copy the patch files to 6.6. Both target drivers/irqchip/irq-realtek-rtl.c
and are additions and fixes for IRQ VPE handling.

Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>

realtek: 6.6: copy patch 311-add-i2c-mux-rtl9300-support

Copy the patch file to 6.6. No further processing required as
it applies cleanly to the new kernel

Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>

realtek: 6.6: refresh patch 310-add-i2c-rtl9300-support

No content changes. Due to kernel changes the patch hooks totally failed
and had to be fixed manually.

Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>

realtek: 6.6: copy patch 310-add-i2c-rtl9300-support

Copy the patch file to 6.6

Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>

realtek: 6.6: refresh patch 307-wdt-update-dependency-for-realtek-otto-wdt

No content changes. Only take over the new patch locations.

Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>

realtek: 6.6: copy patch 307-wdt-update-dependency-for-realtek-otto-wdt

Copy the patch file to 6.6

Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>

realtek: 6.6: refresh patch 305-irqchip-update-dependency-for-irq-realtek-rtl

No content changes. Only take over the new patch locations.

Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>

realtek: 6.6: copy patch 305-irqchip-update-dependency-for-irq-realtek-rtl

Copy the patch file to 6.6

Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>

realtek: 6.6: refresh patch 304-spi-update-dependency-for-spi-realtek-rtl

No content changes. Only take over the new patch locations.

Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>

realtek: 6.6: copy patch 304-spi-update-dependency-for-spi-realtek-rtl

Copy the patch file to 6.6

Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>

ealtek: 6.6: refresh patch 303-gpio-update-dependencies-for-gpio-realtek-otto

No content changes. Only take over the new patch locations.

Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>

realtek: 6.6: copy patch 303-gpio-update-dependencies-for-gpio-realtek-otto

Copy the patch file to 6.6

Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>

realtek: 6.6: refresh patch 302-clocksource-add-otto-driver

No content changes. Only take over the new patch locations.

Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>

realtek: 6.6: copy patch 302-clocksource-add-otto-driver

Copy the patch file to 6.6

Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>

realtek: 6.6: refresh patch 301-gpio-add-rtl8231-driver

No content changes. Only take over the new patch locations.

Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>

realtek: 6.6: copy patch 301-gpio-add-rtl8231-driver

Copy the patch file to 6.6

Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>

realtek: 6.6: refresh patch 300-mips-add-rtl838x-platform

No content changes. Only take over the new patch locations.

Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>

realtek: 6.6: copy patch 300-mips-add-rtl838x-platform

Copy the patch file to 6.6

Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>

realtek: 6.6: fix rtl931x kernel config

The CONFIG_CLOCKSOURCE_WATCHDOG_MAX_SKEW_US is missing. Avoid
complaints and add it with its default 125.

Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>

realtek: 6.6: copy files and config from 5.15

Copy files and config from 5.15 kernel version. Because of the big version jump
leave out the patches for now so we can treat them individually later on.

Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>

realtek: rework hardware-assisted indirect mdio access

With commit b53202a8c3f7 ("realtek: switch to use generic MDIO accessor functions")
the phy access logic was enhanced. A quite big kernel patch was introduced that
allowed to make use of hardware-assisted page access like we have in the realtek
target. Basically it works the following way

- The enhanced bus intercepts page write accesses
- Currently selected pages are stored in internal vars.
- Finally only all-in-one-consistent bus/register accesses are issued
- It intercepted page changes and ensured that only a complete bus call

For the details see https://github.com/openwrt/openwrt/pull/16172

Switching over to newer kernels this patch is really hard to maintain. Its heavy
modifcations exist only in the realtek target. So it does not matter if we keep
it as an kernel modification or directly include it in our driver. To make it the
future brighter we drop this patch and take over its logic. Thus the kernel will
stay totally modification-free. What do we do?

1. Up to now the bus->priv structure directly pointed to ethernet->priv. Create an
explicit private structure rtl838x_bus_priv that not only holds the ethernet->priv
pointer but also space for some bus status tracking vars as well.

2. Wherever we use a reference to ethernet->priv directly replace that by an
additional indirection over the new rtl838x_bus_priv structure.

3. Up to now the phy flag PHY_HAS_REALTEK_PAGES identified that we can use the
alternative paged access from the patch. As this will be no longer available
remove it and provide read_page/write_page functions for each possible PHY.
These functions will be pretty standard as for other Realtek PHYs.

4. The existing mdio bus read/write function rely on the classic MII_ADDR_C45
flag - one interface for two access types. This mixup will be removed on the way
to kernel 6.6. In the future there will be two pairs of access functions. One for
classic access one for c45 style access. Rewrite our functions into 3 parts:

- a classic read/write function: ready for kernel 6.6
- a new c45 read/write function: ready for kernel 6.6
- a legacy read/write wrapper: for current 5.15 for the time being

When we switch to 6.6 we only need to remove the legacy wrappers and link the
new functions. Life can be so easy.

5. The classic read/write functions will incorporate the interception logic that
was originally in the patch.

6. The package convenience functions that were embedded in the patch get lost as
well. Rewrite them inside our phy driver.

Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
[Minor checkpatch.pl cleanups]
Signed-off-by: Sander Vanheule <sander@svanheule.net>

realtek: normalize dts directory

There is no need to keep a version specific dts directory.
Rename the folder to its standard location.

Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>

toolchain/fortify-headers: update download url

Development of fortify-headers has been moved to GitHub.
Gentoo [1] and Alpine Linux [2] already uses it.

Since updating fortify-headers to new version causes a lot of
compile errors, this commit does not bump version.

This commit also refresh patch.

[1]: https://packages.gentoo.org/packages/sys-libs/fortify-headers
[2]: https://git.alpinelinux.org/aports/log/main/fortify-headers

Signed-off-by: Yanase Yuki <dev@zpc.st>
Link: https://github.com/openwrt/openwrt/pull/16374
Signed-off-by: Robert Marko <robimarko@gmail.com>

ipq-wifi: update to Git HEAD (2024-09-14)

2ca41d755d93 qcn9074: add Linksys MX8500 BDF

Link: https://github.com/openwrt/openwrt/pull/16387
Signed-off-by: Robert Marko <robimarko@gmail.com>

ipq-wifi: update to Git HEAD (2024-09-13)

e5b7fb1c606d ipq8074: add Linksys MX8500 BDF

Link: https://github.com/openwrt/openwrt/pull/16382
Signed-off-by: Robert Marko <robimarko@gmail.com>

bpf-headers: fix llvm invocation

- specify CC target explicitly
- define KBUILD_SYM32=n to select "native" build format (if building with 64-bit arch)
- rewrap lines (for good)

Signed-off-by: Konstantin Demin <rockdrilla@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/15702
Signed-off-by: Robert Marko <robimarko@gmail.com>

mediatek: apply pending PHY driver fixes

Apply changes suggested by SkyLake Huang for pending series improving
MediaTek Ethernet PHY drivers.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>

netifd: revert problematic ethtool hack

 02aa43d Revert "system-linux: re-apply ethtool on phy attachment"

Signed-off-by: Daniel Golle <daniel@makrotopia.org>

ct-bugcheck: use . for RELEASE

Adds compatibility for APK.

Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16355
Signed-off-by: Robert Marko <robimarko@gmail.com>

kernel: backport nvmem changes from v6.12

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>

ipq40xx: define config-names for Aruba boards

Aruba boards now ship with multiple DTS and image-configurations per
image. Newer apboot revs expect a configuration for their hardware to be
present.

Signed-off-by: David Bauer <mail@david-bauer.net>

ucode: fix host installation

The path for linking libucode.so was not specified for the ucode binary.
This breaks execution of ucode in the host context.

Signed-off-by: David Bauer <david.bauer@uniberg.com>

treewide: update contact information

Change contact information of comitter as requested.

Reviewed-by: Sarah Mädel <openwrt@tbspace.de>
Signed-off-by: David Bauer <mail@david-bauer.net>

ramips: mt76x8: add missing model string to Yuncore M300

Add missing 'model' string to DT, so /tmp/sysinfo/model gets populated.

Fixes: e497c975d3 ("ramips: mt76x8: add support for Yuncore M300")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>

ramips: mt76x8: add missing model string to Yuncore CPE200

Add missing 'model' string to DT, so /tmp/sysinfo/model gets populated.

Fixes: 64dae1052b ("ramips: mt76x8: add support for Yuncore CPE200")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>

uboot-mediatek: fix OpenWrt One NAND size

The final version of the PCB has 256MB NAND instead of 128MB.

Signed-off-by: John Crispin <john@phrozen.org>

uboot-envtools: add support for OpenWrt One

Signed-off-by: John Crispin <john@phrozen.org>

mediatek: fix OpenWrt One NAND size

The final version of the PCB has 256MB NAND instead of 128MB.

Signed-off-by: John Crispin <john@phrozen.org>

mediatek: fix OpenWrt One MACs

* Ignore the MACs passed by the bootloader.
* fix nvmem-cell-cells warning
* fix the node names
* add dbdc wifi MACs

Signed-off-by: John Crispin <john@phrozen.org>

kernel: backport nvmem changes from v6.11

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>

kernel: backport nvmem changes from v6.10

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>

kernel: backport nvmem changes from v6.9

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>

starfive: drop 6.1 support

Now that 6.6 is the default, remove the 6.1 config and patches.

Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>

starfive: switch default to 6.6

Switch the default kernel to 6.6.

Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>

octeon: set Linux 6.6 as the default kernel

And remove support for 6.1 while at it.

Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/15838
Signed-off-by: Robert Marko <robimarko@gmail.com>

octeon: add support for testing kernel 6.6

A rather trivial addition. Patches automatically rebased. Also add the new
CONFIG_USB_DWC3_OCTEON (disabled) to the generic 6.6 config and sort it, while
at it.

Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/15838
Signed-off-by: Robert Marko <robimarko@gmail.com>

bcm53xx: drop 6.1 support

Drop config and files for Linux 6.1.

Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Link: https://github.com/openwrt/openwrt/pull/16103
Signed-off-by: Robert Marko <robimarko@gmail.com>

bcm53xx: drop 5.15 support

Drop config and files for Linux 5.15.

Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Link: https://github.com/openwrt/openwrt/pull/16103
Signed-off-by: Robert Marko <robimarko@gmail.com>

bcm53xx: use kernel 6.6 by default

Switch to Linux kernel version 6.6.

Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Link: https://github.com/openwrt/openwrt/pull/16103
Signed-off-by: Robert Marko <robimarko@gmail.com>

bpf: fix llvm version check

- specify CC target explicitly

Signed-off-by: Konstantin Demin <rockdrilla@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/15703
Signed-off-by: Robert Marko <robimarko@gmail.com>

kernel: bump 6.6 to 6.6.50

Changelog: https://cdn.kernel.org/pub/linux/kernel/v6.x/ChangeLog-6.6.50

All patch automatically rebased.

Test version: r27317-8e6543fae5
Build system: x86/64
Build-tested: x86/64/AMD Cezanne, flogic/xiaomi_redmi-router-ax6000-ubootmod, ramips/tplink_archer-a6-v3
Run-tested: x86/64/AMD Cezanne, flogic/xiaomi_redmi-router-ax6000-ubootmod, ramips/tplink_archer-a6-v3

Signed-off-by: John Audia <therealgraysky@proton.me>
Link: https://github.com/openwrt/openwrt/pull/16351
Signed-off-by: Nick Hainke <vincent@systemli.org>

kernel: bump 6.1 to 6.1.109

https://cdn.kernel.org/pub/linux/kernel/v6.x/ChangeLog-6.1.109

All patches automatically rebased.

Build system: bcm53xx octeon

Signed-off-by: Zxl hhyccc <zxlhhy@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16353
Signed-off-by: Nick Hainke <vincent@systemli.org>

scripts/feeds: Support feed update with git pull --rebase --autostash

Add feed update option '-s' that performs 'git pull --rebase --autostash':
* possible local uncommited changes are autostashed before pull,
* local commits are then rebased on top of the new commits pulled
  from origin and
* finally git does 'stash pop'.

This enables feed update while there are local development commits
and possibly also local uncommited changes.

Signed-off-by: Hannu Nyman <hannu.nyman@iki.fi>
Link: https://github.com/openwrt/openwrt/pull/15377
Signed-off-by: Robert Marko <robimarko@gmail.com>

scripts/feeds: Support feed update with git pull --rebase

Add feed update option '-r' to perform "git pull --rebase" so that
possible local commits are rebased on top of the new commits pulled
from origin. That enables git pull while there are local
development commits.

Signed-off-by: Hannu Nyman <hannu.nyman@iki.fi>
Link: https://github.com/openwrt/openwrt/pull/15377
Signed-off-by: Robert Marko <robimarko@gmail.com>

rockchip: backport pcie update for rock 5a

This enables the M.2 E-key on ROCK 5A board.
Reorder rk356x patch while at it.

Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
Link: https://github.com/openwrt/openwrt/pull/16340
Signed-off-by: Robert Marko <robimarko@gmail.com>

uboot-rockchip: sort build target alphabetically

move nanopc-t6 recipes above rock 5b.

Fixes: 9482341a4752 ("rockchip: add support for nanopc t6")
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
Link: https://github.com/openwrt/openwrt/pull/16340
Signed-off-by: Robert Marko <robimarko@gmail.com>

ipq807x: add support for TP-Link EAP660 HD v1

Specifications:
* SoC: Qualcomm IPQ8072A (64-bit Quad-core Arm Cortex-A53 @ 2200MHz)
* Memory: 2x ESMT M15T4G16256A-DEBG2G (1 GiB DDR3-1866 13-13-13)
* Serial Port: 3v3 TTL 115200n8
* Wi-Fi: QCN5054 (4x4 5 GHz 802.11ax)
* Wi-Fi: QCN5024 (4x4 2.4 GHz 802.11b/g/n/ax)
* Ethernet: QCA8081 (10/100/1000/2.5GBASE-T)
* Flash: Winbond W29N01HZSINF (128 MiB)
* LEDs: 1x Blue Status (GPIO 42 Active High)
* Buttons: 1x Reset (GPIO 50 Active Low)

Installation Instructions (Serial+TFTP):
1. Solder 4 pin header to JP1 and bridge pads of R58 and R62.
2. Connect 3V3 TTL port to TX, RX, and GND, which are positions 1, 2,
   and 3 respectively. Be sure to crossover TX and RX.
3. Copy RAM firmware image
   openwrt-qualcommax-ipq807x-tplink_eap660hd-v1-initramfs-uImage.itb
   to TFTP server root, available at 192.168.10.1.
4. Connect PoE ethernet cable to the RJ45 port and hold Ctrl+B in the
   serial console (115200 baud) until autoboot is halted.
5. Run the following commands in the U-boot prompt:
   # tftpboot 0x44000000 openwrt-qualcommax-ipq807x-tplink_eap660hd-v1-initramfs-uImage.itb
   # bootm
   You may need to type Ctrl+C and Enter before running these commands
   to clear invisible characters from the buffer.
6. Run the following command in a terminal to copy the sysupgrade image
   to be installed (check IP address):
   $ scp openwrt-qualcommax-ipq807x-tplink_eap660hd-v1-squashfs-sysupgrade.bin root@192.168.1.1:/tmp/
7. Activate the OpenWrt serial console and run the following commands:
   # cd /tmp
   # sysupgrade -n openwrt-qualcommax-ipq807x-tplink_eap660hd-v1-squashfs-sysupgrade.bin
8. The AP will reboot and OpenWrt will be successfully installed.

Signed-off-by: George Witt <george.witt@nltsproject.org>
Link: https://github.com/openwrt/openwrt/pull/15832
Signed-off-by: Robert Marko <robimarko@gmail.com>

uboot-laniq: fix compilation with GCC14

GCC errors on returning int in void function now.

Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16348
Signed-off-by: Robert Marko <robimarko@gmail.com>

starfive: 6.6: add serial1 alias for JH7100

This alias was present in 6.1. Add back to restore a fully working console after
sbi0 (earlycon) gets disabled during the boot process.

Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>

ramips: pinctrl-aw9523: update to current upstream

Various cleanups and bugfixes were applied.

Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16215
Signed-off-by: Robert Marko <robimarko@gmail.com>

mpc85xx: add static to init functions

No reason for them not to be so. Matches various upstream commits for
PPC.

Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16345
Signed-off-by: Robert Marko <robimarko@gmail.com>

mpc85xx: remove calibrate_decr

With upstream commit 0aafbdf35c75cbfec82636d01e6dc7950bc1507c , this is
now default. No need to override.

Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16345
Signed-off-by: Robert Marko <robimarko@gmail.com>

mpc85xx: replace probe with compatible

Upstream commit does this for simple cases, which all of these are.

Commit: 1c96fcdef8c7492ecf34ed70102a1ae5253ef9d1

Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16345
Signed-off-by: Robert Marko <robimarko@gmail.com>

mpc85xx: remove unneeded headers

949e1a0856c4a04ac4a3fee1bd4a0cc69ac187c5 moved this code to DTS. Not
needed anymore.

Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16345
Signed-off-by: Robert Marko <robimarko@gmail.com>

openssl: update to 3.0.15

OpenSSL 3.0.15 is a security patch release. The most severe CVE fixed in this release is Moderate.

This release incorporates the following bug fixes and mitigations:

  * Fixed possible denial of service in X.509 name checks (CVE-2024-6119)

  * Fixed possible buffer overread in SSL_select_next_proto() (CVE-2024-5535)

Added github releases url as source mirror

Signed-off-by: Ivan Pavlov <AuthorReflex@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16332
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>

uboot-envtools: add u-boot system env config for Xiaomi Redmi AX6S

Adds u-boot config for access to system env variables on this board

Signed-off-by: Ivan Pavlov <AuthorReflex@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16312
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>

wireguard-tools: accept iproute2 as dependency

If the user has ip-tiny or ip-full installed there is no need to depend on
BusyBox having any form of `ip` or `ip link` applets.

Signed-off-by: Christian Svensson <blue@cmd.nu>
Link: https://github.com/openwrt/openwrt/pull/16062
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>

kernel: Activate POSIX ACL for f2fs, jffs2 and tmpfs

When CONFIG_USE_FS_ACL_ATTR is set we will also activate POSIX ACL
support for the f2fs, jffs2 and tmpfs file system. This option is
activated on all targets with big flash.

Link: https://github.com/openwrt/openwrt/pull/16181
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>

kernel: activate *_FS_SECURITY and *_FS_ACL_ATTR options for all big flash targets

This patch activate *_FS_SECURITY and *_FS_ACL_ATTR options for all big flash memory targets.
Fixes docker error: "failed to register layer: lsetxattr security.capability /usr/bin/ping: operation not supported"
Forum discussion:
https://forum.openwrt.org/t/docker-pull-fails-failed-to-register-layer-operation-not-supported/138253

Signed-off-by: Leo Barsky <leobrsky@proton.me>
Link: https://github.com/openwrt/openwrt/pull/16181
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>

hostapd: ensure that interface name is not null

Include hotfix suggested by Sebastian Gottschall to fix bug introduced
with APuP patchset

Signed-off-by: Gioacchino Mazzurco <gio@polymathes.cc>
Link: https://github.com/mirror/dd-wrt/commit/0c3001a69e8d8300569e416de856c96e903ad130
Link: https://github.com/openwrt/openwrt/pull/16298
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>

kernel: bump 6.1 to 6.1.108

https://cdn.kernel.org/pub/linux/kernel/v6.x/ChangeLog-6.1.108

All patches automatically rebased.

Build system: bcm53xx octeon

Signed-off-by: Zxl hhyccc <zxlhhy@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16325
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>

kernel: bump 6.6 to 6.6.49

Changelog: https://cdn.kernel.org/pub/linux/kernel/v6.x/ChangeLog-6.6.49

All patches automatically rebased.

Build system: x86/64
Build-tested: x86/64/AMD Cezanne, flogic/xiaomi_redmi-router-ax6000-ubootmod, ramips/tplink_archer-a6-v3
Run-tested: x86/64/AMD Cezanne, flogic/xiaomi_redmi-router-ax6000-ubootmod, ramips/tplink_archer-a6-v3

Signed-off-by: John Audia <therealgraysky@proton.me>
Link: https://github.com/openwrt/openwrt/pull/16328
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>

ltq-ptm: propagate reset errors to probe

Instead of avoiding returning, propagate error so that the kernel
infrastructure can handle it.

Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16262
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>

ltq-atm: propagate EPROBE_DEFER to probe

Instead of ignoring errors, let the linux infrastructure handle it.

Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16262
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>

filogic: add missing 2.5G PHY LEDs configuration for Zyxel EX5700

configure 2.5G PHY LEDs to:

2500/1000: green with blink on TX/RX
100/10: green+yellow with blink on TX/RX

which is similar to other 1G PHY LEDs, which are:

1000: green with blink on TX/RX
100/10: green+yellow with blink on TX/RX

Fixes: 6cc14bf66aa ("filogic: support Telenor branded ZyXEL EX5700")
Signed-off-by: Yan Cangang <nalanzeyu@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16082
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>

mt76: update to Git HEAD (2024-09-05)

5c5e685eb028 wifi: mt76: mt7915: improve hardware recovery
a897606f7c26 wifi: mt76: mt76x0: fix locking regression
65cc3daf2a33 wifi: mt76: support per-band MAC addresses from OF child nodes

Signed-off-by: Felix Fietkau <nbd@nbd.name>

netifd: update to Git HEAD (2024-09-05)

61c606d6e66b device: simplify external device settings handling

Signed-off-by: Felix Fietkau <nbd@nbd.name>

kernel: bridge: fix switchdev host mdb entry updates

Avoid imbalance in host multicast database updates

Signed-off-by: Felix Fietkau <nbd@nbd.name>

bpftool: add host build

Besides probing BPF information in running system, bpftool is also used in
generating skeleton, dumping BTF, etc. that is widely used in modern BPF
development. Make it available as a host tool so that we can use it in
package build.

Tested build targeting malta/le on Arch Linux x86_64. bpftools currently
does not support processing cross-endian BPF objects, so big-endian host
is needed to build for big-endian targets using bpftools.

Signed-off-by: Eric Long <i@hack3r.moe>
Link: https://github.com/openwrt/openwrt/pull/16122
Signed-off-by: Robert Marko <robimarko@gmail.com>

netifd: update to Git HEAD (2024-09-03)

480551a3adc4 interface: add support for disabling renew on topology change
b7b294266781 device: add more debugging code
595094f5c213 device: do not pull device present state from hotplug events
4e11e52e9b98 main: add messages to udebug regardless of their log level
091d063f4a9d wireless: handle link updates even if devices are present already
a8e90853c936 interface: improve hotplug handling reliability
cdb41673ceea device: remove redundant newlines from debug messages
cd2a7964f2c0 device: revert to explicit device_set_present calls

Signed-off-by: Felix Fietkau <nbd@nbd.name>

starfive: enable 6.6 testing kernel

starfive now supports 6.6 kernel as testing.

Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>

starfive: refresh config-6.6

Refresh kernel config for Linux 6.6.

Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>

starfive: add patches for 6.6

Add updated patches for 6.6. DMA/cache-handling patches
have been reworked / backported from upstream.

Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>

kernel/starfive: Restore kernel files for v6.1

This is an automatically generated commit which aids following Kernel patch
history, as git will see the move and copy as a rename thus defeating the
purpose.

For the original discussion see:
https://lists.openwrt.org/pipermail/openwrt-devel/2023-October/041673.html

Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>

kernel/starfive: Create kernel files for v6.6 (from v6.1)

This is an automatically generated commit.

When doing `git bisect`, consider `git bisect --skip`.

Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>

octeon: n821: sysupgrade for Cisco vEdge 1000

This commit adds the logic required to install OpenWrt on a
Cisco/Viptela vEdge 1000 while nicely integrating with the already
present bootloader and making it possible to roll back to stock OS.

The vEdge 1000 has a built-in SSD with a ext2 partition from which
the stock u-boot boots the Linux kernel from.

In order for Linux not to be confused about which partition the root
file system is on, there are some tricks needed to ensure the partition
is identifiable at boot time. For this we use blkid as part of the
scripts, and sfdisk as part of the manual installation process
documented on the wiki. Thus, those packages have been added as a
platform dependency. Finally, the u-boot environment is updated which
requires the use of uboot-envtools.

Tested on a Cisco vEdge 1000.

Signed-off-by: Christian Svensson <blue@cmd.nu>
Link: https://github.com/openwrt/openwrt/pull/16140
Signed-off-by: Robert Marko <robimarko@gmail.com>

ramips: mt76x8: add support for Yuncore CPE200

Yuncore CPE200 is an outdoor unit with IEEE 802.11ac radio.

Hardware:
 - SoC: MediaTek MT7628DAN (MIPS 580MHz)
 - Flash: 8 MiB Spansion S25FL064K
 - RAM: 64 MiB (built-into SoC)
 - WLAN: 5 GHz (MT7613AE)
 - Ethernet: 1x 10/100 Mbps WAN, 1x 10/100 LAN (MT7628)
 - Buttons: 1 Reset button, 2 buttons for display UI (unsupported)
 - LEDs: 4x Green (Power, LAN, WAN, WiFi)
 - Display: 4 digit 7-segment display driven by an additional
            microcontroller (unsupported)
 - Serial console: unpopulated header, 57600 8n1 (RX only)
 - Power: 12 VDC, 1 A

Installation:
The installation can be done via the recovery HTTP server which is built
into the bootloader. Hold down the reset button while connecting the
device to power and keep holding a bit more than 3 seconds. Connect to
http://192.168.0.100/ and upload sysupgrade.bin file.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>

octeon: ubnt-edgerouter: fix sysupgrade config backup/restore

er is missing from platform_copy_config() and octeon_move_config(), so
config is lost on every sysupgrade.

Signed-off-by: Jakob Haufe <sur5r@sur5r.net>
Link: https://github.com/openwrt/openwrt/pull/16238
Signed-off-by: Robert Marko <robimarko@gmail.com>

uboot-mediatek: add missing dependency for mt7988_rfb-spim-nand

Signed-off-by: Felix Fietkau <nbd@nbd.name>

u-boot.mk: pass CROSS_COMPILE during config

Avoids running into unset architecture specific config symbols

Signed-off-by: Felix Fietkau <nbd@nbd.name>

uboot-mediatek: fix build error on mt7981-rfb and openwrt-one

Remove an unnecessary config option that was breaking the build

Signed-off-by: Felix Fietkau <nbd@nbd.name>

uboot-mediatek: fix broken patch

Add missing --- line

Signed-off-by: Felix Fietkau <nbd@nbd.name>

mediatek: mt7988a-rfb: align order of SFPs with SDK build

MediaTek SDK uses eth2 as additional LAN port and eth1 as WAN.
Do the same also in OpenWrt to keep settings aligned with the SDK.

Suggested-by: Bc-bocun Chen <bc-bocun.chen@mediatek.com>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>

qoriq: enable 6.6 testing kernel

The qoriq now supports 6.6 kernel as testing.

Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Link: https://github.com/openwrt/openwrt/pull/16079
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>

qoriq: refresh config-6.6

Refresh kernel config for Linux 6.6.

Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Link: https://github.com/openwrt/openwrt/pull/16079
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>

kernel/qoriq: Restore kernel files for v6.1

This is an automatically generated commit which aids following Kernel patch
history, as git will see the move and copy as a rename thus defeating the
purpose.

For the original discussion see:
https://lists.openwrt.org/pipermail/openwrt-devel/2023-October/041673.html

Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Link: https://github.com/openwrt/openwrt/pull/16079
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>

kernel/qoriq: Create kernel files for v6.6 (from v6.1)

This is an automatically generated commit.

When doing `git bisect`, consider `git bisect --skip`.

Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Link: https://github.com/openwrt/openwrt/pull/16079
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>

kernel: bump 6.1 to 6.1.107

https://cdn.kernel.org/pub/linux/kernel/v6.x/ChangeLog-6.1.107

All patches automatically rebased.

Build system: bcm53xx octeon

Signed-off-by: Zxl hhyccc <zxlhhy@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16283
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>