[POWERPC] MPC5200: Don't make firmware fixups into common code

The Lite5200 u-boot image doesn't entirely configure the processor
correctly and so Linux needs to fixup the cpu setup in setup_arch.  Fixing
the CPU setup is good, but making it into common code is not a good idea.

New board ports should be encouraged not to take the lead of the lite5200
and instead get their firmware to setup the CPU the right way.

Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Sylvain Munaut <tnt@246tnt.com>

[POWERPC] MPC52xx: Trim includes on mpc5200 platform support code

Drop unnecessary includes for MPC5200 based boards

Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Sylvain Munaut <tnt@246tnt.com>

[POWERPC] MPC52xx: Drop show_cpuinfo platform hooks from Lite5200

This hook doesn't really add any new information.

Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Sylvain Munaut <tnt@246tnt.com>

[POWERPC] Lite5200: Use comma delimiter format for lists in device tree

DTC now supports "foo","bar" format for lists of strings; use the new
format on the lite5200 device trees.

Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>

[POWERPC] spi: Support non-QE processors

On non-QE processors (mpc831x/mpc834x) the SPI clock is the SoC clock.

Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>

[POWERPC] 85xx: mpc85xx_mds - reset UCC ethernet properly

Apart from that the current code doesn't compile it's also
meaningless with regard to the MPC8568E-MDS' BCSR.

This patch used to reset UCCs properly.

Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>

[POWERPC] 85xx: mpc8568mds - update dts to be able to use UCCs

1. UCC1's RX_DV pin is 16, not 15;
2. UCC1's phy is at 0x7, not 0x1. Schematics says 0x7, and recent
   u-boot also using 0x7.
3. Use gianfar's (eTSEC) mdio bus. This is hardware default setup.
4. tx-clock should be CLK16 (GE125, PB31);
5. phy-connection-type is RGMII-ID;

Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>

[POWERPC] QE: pario - support for MPC85xx layout

8 bytes padding required to match MPC85xx registers layout.

Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Reviewed-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>

[POWERPC] QEIC: Implement pluggable handlers, fix MPIC cascading

set_irq_chained_handler overwrites MPIC's handle_irq function
(handle_fasteoi_irq) thus MPIC never gets eoi event from the
cascaded IRQ. This situation hangs MPIC on MPC8568E.

To solve this problem efficiently, QEIC needs pluggable handlers,
specific to the underlaying interrupt controller.

Patch extends qe_ic_init() function to accept low and high interrupt
handlers. To avoid #ifdefs, stack of interrupt handlers specified in
the header file and functions are marked 'static inline', thus
handlers are compiled-in only if actually used (in the board file).
Another option would be to lookup for parent controller and
automatically detect handlers (will waste text size because of
never used handlers, so this option abolished).

qe_ic_init() also changed in regard to support multiplexed high/low
lines as found in MPC8568E-MDS, plus qe_ic_cascade_muxed_mpic()
handler implemented appropriately.

Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>

[POWERPC] mpc85xx_mds: select QUICC_ENGINE

Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>

[POWERPC] 86xx: update immap_86xx.h for the 8610

Update the definition of the global utilities structure (ccsr_guts) in
immap_86xx.h and add some related macros for the Freescale 8610 SOC.

Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>

[POWERPC] 85xx/86xx: refactor RSTCR reset code

On the majority of 85xx & 86xx we have a register that's ability to
assert HRESET_REQ to reset the board.  We refactored that code so it
can be shared between both platforms into fsl_soc.c and removed all
the duplication in each platform directory.

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>

[POWERPC] Use for_each_ matching routinues for pci PHBs

On the Freescale embedded (83xx, 85xx, 86xx) and a few of the discrete
bridges (mpc10x, tsi108) use the new for_each_compatible_node() or
for_each_node_by_type() to provide more exact matching when looking for
PHBs in the device tree.

With the previous code it was possible to match on pci bridges since
we were only matching on device_type.

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>

[POWERPC] FSL: Access PCIe LTSSM register with correct size

The LTSSM register is actual 32-bits wide so we should be doing a
dword access.

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>

[POWERPC] 85xx: Failure with odd memory sizes and CONFIG_HIGHMEM

The CONFIG_FSL_BOOKE mmu setup code fails when CONFIG_HIGHMEM=y
and the 3 fixed TLB entries cannot exactly map the lowmem size.
Each TLB entry can map 4MB, 16MB, 64MB or 256MB, so the failure
is observed when the kernel lowmem size is not equal to the
sum of up to 3 of those values.

Normally, memory is sized in nice numbers, but I observed this
problem while testing a crash dump kernel.  The failure can
also be observed by artificially reducing the kernel's main
memory via the mem= kernel command line parameter.

This commit fixes the problem by setting __initial_memory_limit
in adjust_total_lowmem().

Signed-off-by: Dale Farnsworth <dale@farnsworth.org>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>

[POWERPC] Add initial MPC8610 HPCD Platform files.

Add basic board support for the MPC8610 HPCD.  This does
not include any support the SoC Display or Audio controllers.

Signed-off-by: Xianghua Xiao <x.xiao@freescale.com>
Signed-off-by: Jason Jin <Jason.jin@freescale.com>
Signed-off-by: Jon Loelier <jdl@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>

[POWERPC] Treat 8610 PCIe host bridge as transparent

Signed-off-by: Jason Jin <Jason.jin@freescale.com>
Signed-off-by: Jon Loeliger <jdl@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>

[POWERPC] Add initial MPC8610 HPCD Device Tree Source file.

Signed-off-by: Xianghua Xiao <x.xiao@freescale.com>
Signed-off-by: Jon Loeliger <jdl@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>

[POWERPC] spi: mode should be "cpu-qe" instead of "qe"

Mode should be "cpu-qe" for QE in CPU mode. "qe" should be reserved
for native QE mode.

Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>

[POWERPC] spi: Use fsl_spi instead of mpc83xx_spi

According to booting-without-of.txt, compatible should be "fsl_spi" and
mode "cpu" or "qe" for the fsl SPI controllers.

Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>

[POWERPC] qe: miscellaneous code improvements and fixes to the QE library

This patch makes numerous miscellaneous code improvements to the QE library.

1. Remove struct ucc_common and merge ucc_init_guemr() into ucc_set_type()
   (every caller of ucc_init_guemr() also calls ucc_set_type()).  Modify all
   callers of ucc_set_type() accordingly.

2. Remove the unused enum ucc_pram_initial_offset.

3. Refactor qe_setbrg(), also implement work-around for errata QE_General4.

4. Several printk() calls were missing the terminating \n.

5. Add __iomem where needed, and change u16 to __be16 and u32 to __be32 where
   appropriate.

6. In ucc_slow_init() the RBASE and TBASE registers in the PRAM were programmed
   with the wrong value.

7. Add the protocol type to struct us_info and updated ucc_slow_init() to
   use it, instead of always programming QE_CR_PROTOCOL_UNSPECIFIED.

8. Rename ucc_slow_restart_x() to ucc_slow_restart_tx()

9. Add several macros in qe.h (mostly for slow UCC support, but also to
   standardize some naming convention) and remove several unused macros.

10. Update ucc_geth.c to use the new macros.

11. Add ucc_slow_info.protocol to specify which QE_CR_PROTOCOL_xxx protcol
    to use when initializing the UCC in ucc_slow_init().

12. Rename ucc_slow_pram.rfcr to rbmr and ucc_slow_pram.tfcr to tbmr, since
    these are the real names of the registers.

13. Use the setbits, clrbits, and clrsetbits where appropriate.

14. Refactor ucc_set_qe_mux_rxtx().

15. Remove all instances of 'volatile'.

16. Simplify get_cmxucr_reg();

17. Replace qe_mux.cmxucrX with qe_mux.cmxucr[].

18. Updated struct ucc_geth because struct ucc_fast is not padded any more.

Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>

[POWERPC] Update .gitignore for new vdso generated files

We now generate vdso[32,64].so.dbg as part of the build so
add them to .gitignore

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>

[POWERPC] Fixup MPC8568 dts

The PCI nodes on the MPC8568 dts didn't get moved up to be sibilings of the
SOC node when we did that clean up for some reason.  Fix that up and some
minor whitespace and adjusting the size of the soc reg property.

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>

[POWERPC] mpc8568mds.dts: fix PCIe I/O address space location and size

According to u-boot/board/mpc8568mds/init.S:

LAW(Local Access Window) configuration:
2)   0xa000_0000   0xbfff_ffff     PCIe MEM                512MB
4)   0xe280_0000   0xe2ff_ffff     PCIe I/O                8M

Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>

[POWERPC] MPC8568E-MDS: add support for ds1374 rtc

MPC8568E-MDS have DS1374 chip on the I2C bus, thus let's use it.
This patch also adds #address-cells and #size-cells to the I2C
controllers nodes.

p.s. DS1374 rtc class driver is in the -mm tree, its name is
rtc-rtc-class-driver-for-the-ds1374.patch.

Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>

[POWERPC] fsl_soc: fix uninitialized i2c_board_info structure

i2c_board_info used semi-initialized, causing garbage in the
info->flags, and that, in turn, causes various symptoms of i2c
malfunctioning, like PEC mismatches.

Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>

[POWERPC] cpm: Describe multi-user ram in its own device node.

The way the current CPM binding describes available multi-user (a.k.a.
dual-ported) RAM doesn't work well when there are multiple free regions,
and it doesn't work at all if the region doesn't begin at the start of
the muram area (as the hardware needs to be programmed with offsets into
this area).  The latter situation can happen with SMC UARTs on CPM2, as its
parameter RAM is relocatable, u-boot puts it at zero, and the kernel doesn't
support moving it.

It is now described with a muram node, similar to QE.  The current CPM
binding is sufficiently recent (i.e. never appeared in an official release)
that compatibility with existing device trees is not an issue.

The code supporting the new binding is shared between cpm1 and cpm2, rather
than remain separated.  QE should be able to use this code as well, once
minor fixes are made to its device trees.

Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>

[POWERPC] Cleaned up whitespace in head_fsl_booke.S

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>

[POWERPC] QE: Added missing CEURNR register

According to the publicly available MPC8360E RM (rev. 1 from 09/2006 and rev. 2
from 05/2007) and MPC8323E RM (rev. 1 from 09/2006), CEURNR is the QE microcode
revision number register and is located at offset 0x1b8 within the QE internal
register space

Signed-off-by: Emil Medve <Emilian.Medve@Freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>

[POWERPC] fsl_soc: rtc-ds1307 support

Add support for the I2C devices handled by the rtc-ds1307 driver to
of_register_i2c_devices.

Cc: G. Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>

[POWERPC] fsl_soc: Fix trivial printk typo.

Fix a trivial printk typo in fsl_soc.

Cc: G. Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>

[POWERPC] 8xx: Move softemu8xx.c from arch/ppc

Previously, Soft_emulate_8xx was called with no implementation, resulting in
build failures whenever building 8xx without math emulation.  The
implementation is copied from arch/ppc to resolve this issue.

However, this sort of minimal emulation is not a very good idea other than
for compatibility with existing userspaces, as it's less efficient than
soft-float and can mislead users into believing they have soft-float.  Thus,
it is made a configurable option, off by default.

Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>

[POWERPC] bootwrapper: adds cuboot for MPC7448HPC2 platform

This patch adds cuboot support for MPC7448HPC2 platform.
The cuImage can be used with legacy u-boot without FDT support.

Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>

[POWERPC] mpc82xx: Add pq2fads board support.

Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>

[POWERPC] mpc82xx: Update mpc8272ads, and factor out PCI and reset.

1. PCI and reset are factored out into pq2.c.  I renamed them from m82xx
to pq2 because they won't work on the Integrated Host Processor line of
82xx chips (i.e. 8240, 8245, and such).

2. The PCI PIC, which is nominally board-specific, is used on multiple
boards, and thus is used into pq2ads-pci-pic.c.

3. The new CPM binding is used.

4. General cleanup.

Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>

[POWERPC] 8xx/wrapper: Embedded Planet EP88xC support

This board is also resold by Freescale under the names
"QUICCStart MPC885 Evaluation System" and "CWH-PPC-885XN-VE".

Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>

[POWERPC] 8xx: mpc885ads cleanup

It now uses the new CPM binding and the generic pin/clock functions, and
has assorted fixes and cleanup.

Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>

[POWERPC] Document local bus nodes in the device tree, and update cuboot-pq2.

The localbus node is used to describe devices that are connected via a chip
select or similar mechanism.  The advantages over placing the devices under
the root node are that it can be probed without probing other random things
under the root, and that the description of which chip select a given device
uses can be used to set up mappings if the firmware failed to do so in a
useful manner.

cuboot-pq2 is updated to match the binding; previously, it called itself
chipselect rather than localbus, and used phandle linkage between the
actual bus node and the control node (the current agreement is to simply use
the fully-qualified address of the control registers, and ignore the overlap
with the IMMR node).

Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>

[POWERPC] mpc8272ads: Change references from 82xx_ADS to 8272_ADS.

Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>

[POWERPC] mpc82xx: Rename mpc82xx_ads to mpc8272_ads.

This is just a rename patch; internal references to mpc82xx_ads will be
changed in the next one.

Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>

[POWERPC] mpc82xx: Remove a bunch of cruft that duplicates generic functionality.

m82xx_calibrate_decr(), mpc82xx_ads_show_cpuinfo(), and mpc82xx_halt() do
anything useful beyond what the generic code does.

Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>

[POWERPC] mpc82xx: Define CPU_FTR_NEED_COHERENT

The 8272 (and presumably other PCI PQ2 chips) appear to have the
same issue as the 83xx regarding PCI streaming DMA.

Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>

[POWERPC] cpm2: Add cpm2_set_pin().

This provides a generic way for board code to set up CPM pins, rather
than directly poking magic values into registers.

Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>

[POWERPC] cpm2: Add SCCs to cpm2_clk_setup(), and cpm2_smc_clk_setup().

Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>

[POWERPC] cpm2: Infrastructure code cleanup.

Mostly sparse fixes (__iomem annotations, etc); also, cpm2_immr
is used rather than creating many temporary mappings.

Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>

[POWERPC] 8xx: Set initial memory limit.

The 8xx can only support a max of 8M during early boot (it seems a lot of
8xx boards only have 8M so the bug was never triggered), but the early
allocator isn't aware of this.  The following change makes it able to run
with larger memory.

Signed-off-by: John Traill <john.traill@freescale.com>
Signed-off-by: Vitaly Bordug <vitb@kernel.crashing.org>
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>

[POWERPC] 8xx: Work around CPU15 erratum.

The CPU15 erratum on MPC8xx chips can cause incorrect code execution
under certain circumstances, where there is a conditional or indirect
branch in the last word of a page, with a target in the last cache line
of the next page.  This patch implements one of the suggested
workarounds, by forcing a TLB miss whenever execution crosses a page
boundary.  This is done by invalidating the pages before and after the
one being loaded into the TLB in the ITLB miss handler.

Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>

[POWERPC] 8xx: Add pin and clock setting functions.

These let board code set up pins and clocks without having to
put magic numbers directly into the registers.

The clock function is mostly duplicated from the cpm2 version;
hopefully this stuff can be merged at some point.

Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>

[POWERPC] 8xx: Infrastructure code cleanup.

1. Keep a global mpc8xx_immr mapping, rather than constantly
creating temporary mappings.
2. Look for new fsl,cpm1 and fsl,cpm1-pic names.
3. Always reset the CPM when not using the udbg console;
this is required in case the firmware initialized a device
that is incompatible with one that the kernel is about to
use.
4. Remove some superfluous casts and header includes.
5. Change a usage of IMAP_ADDR to get_immrbase().
6. Use phys_addr_t, not uint, for dpram_pbase.
7. Various sparse-related fixes, such as __iomem annotations.
8. Remove mpc8xx_show_cpuinfo, which doesn't provide anything
useful beyond the generic cpuinfo handler.
9. Move prototypes for 8xx support functions from board files
to sysdev/commproc.h.

Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>

[POWERPC] 8xx: Fix CONFIG_PIN_TLB.

1. Move CONSISTENT_START on 8xx so that it doesn't overlap the IMMR mapping.
2. The wrong register was being loaded into SPRN_MD_RPN.

Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>

[POWERPC] cpm_uart: Issue STOP_TX command before initializing console.

This prevents some bootloader/bootwrapper characters from being lost.

Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>

[POWERPC] cpm_uart: sparse fixes

Mostly a bunch of direct access to in/out conversions, plus a few
cast removals, __iomem annotations, and miscellaneous cleanup.

Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>

[POWERPC] cpm_uart: Be an of_platform device when CONFIG_PPC_CPM_NEW_BINDING is set.

The existing OF glue code was crufty and broken.  Rather than fix it,
it has been removed, and the serial driver now talks to the device tree
directly.

The non-CONFIG_PPC_CPM_NEW_BINDING code can go away once CPM platforms
are dropped from arch/ppc (which will hopefully be soon), and existing
arch/powerpc boards that I wasn't able to test on for this patchset get
converted (which should be even sooner).

Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>

[POWERPC] bootwrapper: Use fsl_get_immr() in cuboot-pq2.c.

Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>

[POWERPC] bootwrapper: Add fsl_get_immr() and 8xx/pq2 clock functions.

fsl_get_immr() uses /soc/ranges to determine the immr.

mpc885_get_clock() transforms a crystal frequency into a system frequency
according to the PLL register settings.

pq2_get_clocks() does the same as the above for the PowerQUICC II,
except that it produces several different clocks.

The mpc8xx/pq2 set_clocks() functions modify common properties in
the device tree based on the given clock data.

The mpc885/pq2 fixup_clocks() functions call get_clocks(), and
pass the results to set_clocks().

Signed-off-by: Scott Wood <scottwood@freescale.com>
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>

[POWERPC] bootwrapper: Support all-in-one PCI nodes in cuboot-pq2.

Consensus was reached to put PCI nodes at the root of the tree (and not
under /soc), but the phandle to a control node was rejected in favor of
simply not worrying about /pci/reg overlapping /soc/ranges.

This updates cuboot-82xx to not look for the phandle.

Signed-off-by: Scott Wood <scottwood@freescale.com>
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>

[POWERPC] Add early debug console for CPM serial ports.

This code assumes that the ports have been previously set up, with
buffers in DPRAM.

Signed-off-by: Scott Wood <scottwood@freescale.com>
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>

[POWERPC] Introduce new CPM device bindings.

This introduces a new device binding for the CPM and other devices on
these boards.  Some of the changes include:

1. Proper namespace scoping for Freescale compatibles and properties.

2. Use compatible rather than things like device_type and model
to determine which particular variant of a device is present.

3. Give the drivers the relevant CPM command word directly, rather than
requiring it to have a lookup table based on device-id, SCC v. SMC, and
CPM version.

4. Specify the CPCR and the usable DPRAM region in the CPM's reg property.

Boards that do not require the legacy bindings should select
CONFIG_PPC_CPM_NEW_BINDING to enable the of_platform CPM devices. Once
all existing boards are converted and tested, the config option can
become default y to prevent new boards from using the old model.  Once
arch/ppc is gone, the config option can be removed altogether.

Signed-off-by: Scott Wood <scottwood@freescale.com>
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>

[POWERPC] CPM: Change from fsl,brg-frequency to brg/clock-frequency

As suggested by David Gibson, now that we have a separate node
for the baud rate generators, it's better to use the standard
clock-frequency property than a cpm-node-level fsl,brg-frequency
property.

This patch updates existing places where fsl,brg-frequency is
used.

Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>

[PPC] Use cpu setup routines from cpu_setup_44x.S for ARCH=ppc

Commit 8112753bb2c0045398c89d0647792b39805f6d40 made 44x in
ARCH=powerpc builds use cpu setup routines in cpu_setup_44x.S,
but didn't make a similar change for ARCH=ppc, and consequently
the ARCH=ppc builds fail with undefined symbols (since both use
the same cputable.c).

This fixes it by including cpu_setup_44x.S in the ARCH=ppc builds,
and by taking out the now-redundant FPU initialization in
arch/ppc/kernel/head_44x.S.

Signed-off-by: Paul Mackerras <paulus@samba.org>

[POWERPC] Uartlite: Revert register io access changes

Reverts commit a15da8eff3627b8368db7f5dd260e5643213d918

This driver is used by devices other than the xilinx opb-uartlite which
depend on bytewise access to the registers.  The change to 32 bit access
does not work on these devices.

Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Peter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>

[POWERPC] Uartlite: Add macros for register names

Add macros to define register names to improve readability.

Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>

[POWERPC] Setup default eth addr in embed_config for Xilinx Virtex platforms

This simply adds the boilerplate default Ethernet address to embed_config
for the Xilinx platform (bug fix).

Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>

[POWERPC] XilinxFB: Move xilinxfb_platform_data definition to a shared header file

XilnixFB can be used by more than just arch/ppc.  Move the data structure
definition into include/linux/xilinxfb.h so it can be used by microblaze
and arch/powerpc

Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>

[POWERPC] Uartlite: Flush RX fifo in bootwrapper

Flush the uartlite RX fifo so that characters typed before entry into
the zImage wrapper do not muck up the kernel command line.

Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>

[POWERPC] Add treeImage to .gitignore

Tell git to ignore the generated treeImage.* files in arch/powerpc/boot

Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>

[POWERPC] Uartlite: Let the console be initialized earlier

By configuring it earlier we get console output sooner which is helpful
for debugging when the kernel crashes before the serial drivers are
initialized.

Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>

[POWERPC] Uartlite: Add of-platform-bus binding

Add of_platform bus binding so this driver can be used with arch/powerpc

Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>

[POWERPC] Uartlite: Comment block tidy

Tidy the comments to split the driver into logical section; the main driver,
the console driver, the platform bus binding, and module initialization
and teardown.

Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>

[POWERPC] Uartlite: Separate the bus binding from the driver proper

Separate the bus binding code from the driver structure allocation code in
preparation for adding the of_platform_bus bindings needed by arch/powerpc

Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>

[POWERPC] Uartlite: Add macro for uartlite device name

Changed to make the following OF_platform bus binding patch a wee bit cleaner

Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>

[POWERPC] Uartlite: change name of ports to ulite_ports

Changed to match naming convention used in the rest of the module

Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>

[POWERPC] Uartlite: Fix reg io to access documented register size

The Uartlite data sheet defines the registers as 32 bit wide.  This
patch changes the register access to use 32 bit transfers and eliminates
the magic +3 offset which is currently required to make the device
work.

Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: John Williams <jwilliams@itee.uq.edu.au>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>

[POWERPC] Add PowerPC Xilinx Virtex entry to maintainers

Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>

[POWERPC] Virtex: Add generic Xilinx Virtex board support

Adds support for generic Xilinx Virtex boards.  Any board which specifies
"xilinx,virtex" in the compatible property will make use of this board
support.

Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>

[POWERPC] Virtex: add xilinx interrupt controller driver

Adds support for the Xilinx opb-intc interrupt controller

Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>

[POWERPC] Virtex: Add Kconfig macros for Xilinx Virtex board support

Add the needed kconfig macros to enable Xilinx Virtex board support

Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>

[POWERPC] Virtex: Add uartlite bootwrapper driver

Allows the bootwrapper to use the uartlite device for console output.

Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>

[POWERPC] 4xx: 440EPx/GRx incorrect write to DDR SDRAM errata workaround

Add a workaround for PowerPC 440EPx/GRx incorrect write to
DDR SDRAM errata. Data can be written to wrong address
in SDRAM when write pipelining enabled on plb0. We disable
it in the cpu_setup for these processors at early init.

Signed-off-by: Valentine Barshak <vbarshak@ru.mvista.com>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>

[POWERPC] 4xx: Move 440EP(x) FPU setup from head_44x to cpu_setup_4xx

The PowerPC 440EP(x) FPU init is currently done in head_44x
under ifdefs. Since we should support more then one board
in the same kernel, we move FPU initialization code from head_44x
to cpu_setup_44x and add cpu_setup callbacks for 440EP(x).

Signed-off-by: Valentine Barshak <vbarshak@ru.mvista.com>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>

[POWERPC] 4xx: Introduce cpu_setup functionality to 44x platform

This adds cpu_setup functionality for ppc44x platform.
Low level cpu-spefic initialization routines should be
placed in cpu_setup_44x.S and a callback should be
added to cputable. The cpu_setup is invoked
by identify_cpu() function at early init.

Signed-off-by: Valentine Barshak <vbarshak@ru.mvista.com>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>

[POWERPC] 4xx: Fix Walnut wrapper compile errors

Pass the appropriate -mcpu flag to the treeboot-walnut.o object to prevent
some toolchains from erroring out with unknown opcodes

Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>

[POWERPC] Enable tickless idle and high res timers for powerpc

Signed-off-by: Tony Breeds <tony@bakeyournoodle.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>

[POWERPC] Implement clockevents driver for powerpc

This registers a clock event structure for the decrementer and turns
on CONFIG_GENERIC_CLOCKEVENTS, which means that we now don't need
most of timer_interrupt(), since the work is done in generic code.
For secondary CPUs, their decrementer clockevent is registered when
the CPU comes up (the generic code automatically removes the
clockevent when the CPU goes down).

Signed-off-by: Tony Breeds <tony@bakeyournoodle.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>

Merge branch 'ppc-fixes' of git://git.bocc.de/dbox2 into for-2.6.24

Merge branch 'linux-2.6' into for-2.6.24

[POWERPC] Fix panic in RTAS code

Some older pSeries machines were panicking in pSeries_log_error
because it was getting called before it was ready.  This is a result
of commit "[POWERPC] pseries: Fix jumbled no_logging flag."
(79c0108d1b9db4864ab77b2a95dfa04f2dcf264c).

This fixes it by explicitly enabling RTAS error logging when it has
been initialized, and also makes the code clearer by renaming the
"no_more_logging" variable to "logging_enabled".

Signed-off-by: Tony Breeds <tony@bakeyournoodle.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>

[POWERPC] Use alloc_maybe_bootmem() in pcibios_alloc_controller

Use alloc_maybe_bootmem() which wraps the if (mem_init_done)
malloc clause.

Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>

[POWERPC] Celleb: update for PCI

This adds support for the PCI bus on Celleb with new "I/O routines
for PowerPC."  External PCI on Celleb must do explicit synchronization
with devices (Bus has no automatic synchronization feature).

Signed-off-by: Kou Ishizaki <Kou.Ishizaki@toshiba.co.jp>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Paul Mackerras <paulus@samba.org>

[POWERPC] Celleb: Serial I/O update

This is an update for Serial I/O on Celleb.
  - Detection algorithm has been changed

Signed-off-by: Kou Ishizaki <Kou.Ishizaki@toshiba.co.jp>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Paul Mackerras <paulus@samba.org>

[POWERPC] Celleb: New HTAB Guest OS Interface on Beat

This changes the Celleb code to work with new Guest OS Interface
to tweak HTAB on Beat. It detects old and new Guest OS Interfaces
automatically.

Signed-off-by: Kou Ishizaki <Kou.Ishizaki@toshiba.co.jp>
Acked-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>

[POWERPC] Celleb: Support for Power/Reset buttons

This supports Power/Reset buttons on Beat on Celleb.

On Beat, we have an event from Beat if Power button or Reset button
is pressed. This patch catches the event and convert it to a signal
to INIT process by calling ctrl_alt_del() function.

/sbin/inittab have no entry to turn the machine power off so we have
to detect if power button is pressed or not internally in our driver.
This idea is taken from PS3's event handling subsystem.

Signed-off-by: Kou Ishizaki <Kou.Ishizaki@toshiba.co.jp>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Paul Mackerras <paulus@samba.org>

[POWERPC] Celleb: Move pause, kexec_cpu_down to beat.c

This is an update for "Beat on Celleb"
  - Move beat_pause(), beat_kexec_cpu_down() from setup.c to beat.c

Signed-off-by: <Kou.Ishizaki@toshiba.co.jp>
Acked-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>

[POWERPC] ibmebus: More descriptive error return code in ibmebus_store_probe()

Signed-off-by: Joachim Fenkes <fenkes@de.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>

[POWERPC] Update axon_msi to use dcr_host_t.base

Now that dcr_host_t contains the base address, we can use that in the
axon_msi code, rather than storing it separately.

Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>

[POWERPC] Update mpic to use dcr_host_t.base

Now that dcr_host_t contains the base address, we can use that in the mpic
code, rather than storing it separately.

Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>

[POWERPC] Store the base address in dcr_host_t

In its current form, dcr_map() doesn't remember the base address you passed
it, which means you need to store it somewhere else.  Rather than adding the
base to another struct it seems simpler to store it in the dcr_host_t.

Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>

[POWERPC] Select proper defconfig for crosscompiles

The trick for finding the right defconfig is neat, but you forgot to
provide an i686_defconfig.  ;-)

More seriously, cross compiling the defconfig is often useful, e.g. for
testing the compilation of patches that touch multiple architectures,
and this patch therefore chooses g5_defconfig if $(CROSS_COMPILE) is
non-empty.

Signed-off-by: Adrian Bunk <bunk@kernel.org>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Olof Johansson <olof@lixom.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>

[POWERPC] Sky Cpu and Nexus: use seq_file/single_open on proc interface

This patch changes proc interface to be used with single_file/seq_open
calls.

Signed-off-by: Cyrill Gorcunov <gorcunov@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>

[POWERPC] Sky Cpu: use C99 style for struct init

This changes structure item init format to C99, and removes useless
structure items init.

Signed-off-by: Cyrill Gorcunov <gorcunov@gmail.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Kumar Gala <galak@gate.crashing.org>
Cc: Brian Waite <waite@skycomputers.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>