git.openwrt.org Git - openwrt/staging/blogic.git/log

drm/i915/dma: prefer struct drm_i915_private to drm_i915_private_t

Also drop any unnecessary casts. No functional changes.

Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

drm/i915/debugfs: prefer struct drm_i915_private to drm_i915_private_t

No functional changes.

Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

drm/i915: Mask PM/RPS interrupt generation based on activity

The speculation is that we can conserve more power by masking off
the interrupts at source (PMINTRMSK) rather than filtering them by the
up/down thresholds (RPINTLIM). We can select which events we know will
be active based on the current frequency versus our imposed range, i.e.
if at minimum, we know we will not want to generate any more
down-interrupts and vice versa.

v2: We only need the TIMEOUT when above min frequency.
v3: Tweak VLV at the same time

Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Deepak S <deepak.s@linux.intel.com>
Reviewed-by:Deepak S <deepak.s@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

drm/i915: Refactor gen6_set_rps

What used to be a short-circuit now needs to adjust interrupt masking in
response to user requests for changing the min/max allowed frequencies.
This is currently done by a special case and early return, but the next
patch adds another common action to take, so refactor the code to reduce
duplication.

Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by:Deepak S <deepak.s@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

Revert "drm/i915: Disable/Enable PM Intrrupts based on the current freq."

This reverts commit 2754436913b94626a5414d82f0996489628c513d.

Conflicts:
drivers/gpu/drm/i915/i915_irq.c

The partial application of interrupt masking without regard to other
pathways for adjusting the RPS frequency results in completely disabling
the PM interrupts. This leads to excessive power consumption as the GPU
is kept at max clocks (until the failsafe mechanism fires of explicitly
downclocking the GPU when all requests are idle). Or equally as bad for
the UX, the GPU is kept at minimum clocks and prevented from upclocking
in response to a requirement for more power.

Testcase: pm_rps/blocking
Cc: Deepak S <deepak.s@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by:Deepak S <deepak.s@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

drm/i915: Make sure vsyncshift is positive

If vsyncshift comes out as negative, add one htotal to it to get the
corresponding positive value.

This is rather theoretical as it would require a mode where the
hsync+back porch is very long and the active+front porch very short.

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

drm/i915: Fix the interlace mode selection for gmch platforms

PIPECONF_INTERLACE_W_FIELD_INDICATION is only meant to be used for sdvo
since it implies a slightly weird vsync shift of htotal/2. For everything
else we should use PIPECONF_INTERLACE_W_SYNC_SHIFT and let the value in
the VSYNCSHIFT register take effect.

The only exception is gen3 simply because VSYNCSHIFT didn't exist yet.
Gen2 doesn't support interlaced modes at all, so we can drop the
explicit gen2 checks.

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

drm/i915: Program VSYNCSHIFT in a more consistent manner

When interlaced sdvo output is used, vsyncshift should supposedly
be (htotal-1)/2. In reality PIPECONF/TRANSCONF will override it by
using the legacy vsyncshift interlace mode which causes the hardware
to ignore the VSYNCSHIFT register.

The only odd thing here is that on PCH platforms we program the
VSYNCSHIFT on both CPU and PCH, and it's not entirely clear if both
sides have to agree on the value or not. On the CPU side there's no
way to override the value via PIPECONF anymore, so if we want to make
the CPU side agree with the PCH side, we should probably program the
approriate value into VSYNCSHIFT manually. So let's do that, but for
now leave the PCH side to still use the legacy interlace mode in
TRANSCONF.

We can also drop the gen2 check since gen2 doesn't support interlaced
modes at all.

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

drm/i915/vlv: use W_SYNC_SHIFT for interlaced modes on VLV

This makes HDMI testers happier on VLV platforms. It may be that we
need it for any non-SVO platform, but I don't have any tests to back
that up, so I'm leaving other pre-ILK platforms alone for now.

Tested-by: "Clint Taylor <clinton.a.taylor@intel.com>"
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=74964
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

drm/i915: restrict vt-d stolen memory workaround to pre-gen8

We want future generations to at least attempt to use all features, so
restrict the stolen memory disabling when vt-d is enabled to the
latest generation we have reports for. Which is a HSW per the original
report.

Also once we get a bit a hold of some of the mysterious framebuffer in
stolen memory issues that still haunt bugzilla, we should probably
drop this hack again and see what happens.

This was introduced in

commit 0f4706d2740f2a221cd502922b22e522009041d9
Author: Chris Wilson <chris@chris-wilson.co.uk>
Date: Tue Mar 18 14:50:50 2014 +0200

drm/i915: Disable stolen memory when DMAR is active

Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: David Woodhouse <dwmw2@infradead.org>
References: https://bugs.freedesktop.org/show_bug.cgi?id=68535
Acked-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

Merge tag 'v3.14' into drm-intel-next-queued

Linux 3.14

The vt-d w/a merged late in 3.14-rc needs a bit of fine-tuning, hence
backmerge.

Conflicts:
drivers/gpu/drm/i915/i915_gem_gtt.c
drivers/gpu/drm/i915/intel_ddi.c
drivers/gpu/drm/i915/intel_dp.c

All trivial adjacent lines changed type conflicts, so trivial git
doesn't even show them in the merg commit.

Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

Linux 3.14

Merge branch 'for-linus-2' of git://git./linux/kernel/git/viro/vfs

Pull vfs fixes from Al Viro:
"Switch mnt_hash to hlist, turning the races between __lookup_mnt() and
  hash modifications into false negatives from __lookup_mnt() (instead
  of hangs)"

On the false negatives from __lookup_mnt():
"The *only* thing we care about is not getting stuck in __lookup_mnt().
  If it misses an entry because something in front of it just got moved
  around, etc, we are fine.  We'll notice that mount_lock mismatch and
  that'll be it"

* 'for-linus-2' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
  switch mnt_hash to hlist
  don't bother with propagate_mnt() unless the target is shared
  keep shadowed vfsmounts together
  resizable namespace.c hashes

MAINTAINERS: resume as Documentation maintainer

I am the new kernel tree Documentation maintainer (except for parts that
are handled by other people, of course).

Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Acked-by: Rob Landley <rob@landley.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Merge branch 'for-linus' of git://git./linux/kernel/git/dtor/input

Pull input updates from Dmitry Torokhov:
"Some more updates for the input subsystem.

  You will get a fix for race in mousedev that has been causing quite a
  few oopses lately and a small fixup for force feedback support in
  evdev"

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
  Input: mousedev - fix race when creating mixed device
  Input: don't modify the id of ioctl-provided ff effect on upload failure

AUDIT: Allow login in non-init namespaces

It its possible to configure your PAM stack to refuse login if audit
messages (about the login) were unable to be sent.  This is common in
many distros and thus normal configuration of many containers.  The PAM
modules determine if audit is enabled/disabled in the kernel based on
the return value from sending an audit message on the netlink socket.
If userspace gets back ECONNREFUSED it believes audit is disabled in the
kernel.  If it gets any other error else it refuses to let the login
proceed.

Just about ever since the introduction of namespaces the kernel audit
subsystem has returned EPERM if the task sending a message was not in
the init user or pid namespace.  So many forms of containers have never
worked if audit was enabled in the kernel.

BUT if the container was not in net_init then the kernel network code
would send ECONNREFUSED (instead of the audit code sending EPERM).  Thus
by pure accident/dumb luck/bug if an admin configured the PAM stack to
reject all logins that didn't talk to audit, but then ran the login
untility in the non-init_net namespace, it would work!! Clearly this was
a bug, but it is a bug some people expected.

With the introduction of network namespace support in 3.14-rc1 the two
bugs stopped cancelling each other out.  Now, containers in the
non-init_net namespace refused to let users log in (just like PAM was
configfured!) Obviously some people were not happy that what used to let
users log in, now didn't!

This fix is kinda hacky.  We return ECONNREFUSED for all non-init
relevant namespaces.  That means that not only will the old broken
non-init_net setups continue to work, now the broken non-init_pid or
non-init_user setups will 'work'.  They don't really work, since audit
isn't logging things.  But it's what most users want.

In 3.15 we should have patches to support not only the non-init_net
(3.14) namespace but also the non-init_pid and non-init_user namespace.
So all will be right in the world.  This just opens the doors wide open
on 3.14 and hopefully makes users happy, if not the audit system...

Reported-by: Andre Tomt <andre@tomt.net>
Reported-by: Adam Richter <adam_richter2004@yahoo.com>
Signed-off-by: Eric Paris <eparis@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

ext4: atomically set inode->i_flags in ext4_set_inode_flags()

Use cmpxchg() to atomically set i_flags instead of clearing out the
S_IMMUTABLE, S_APPEND, etc. flags and then setting them from the
EXT4_IMMUTABLE_FL, EXT4_APPEND_FL flags, since this opens up a race
where an immutable file has the immutable flag cleared for a brief
window of time.

Reported-by: John Sullivan <jsrhbz@kanargh.force9.co.uk>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
Cc: stable@kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

switch mnt_hash to hlist

fixes RCU bug - walking through hlist is safe in face of element moves,
since it's self-terminating. Cyclic lists are not - if we end up jumping
to another hash chain, we'll loop infinitely without ever hitting the
original list head.

[fix for dumb braino folded]

Spotted by: Max Kellermann <mk@cm4all.com>
Cc: stable@vger.kernel.org
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>

don't bother with propagate_mnt() unless the target is shared

If the dest_mnt is not shared, propagate_mnt() does nothing -
there's no mounts to propagate to and thus no copies to create.
Might as well don't bother calling it in that case.

Cc: stable@vger.kernel.org
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>

keep shadowed vfsmounts together

preparation to switching mnt_hash to hlist

Cc: stable@vger.kernel.org
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>

resizable namespace.c hashes

* switch allocation to alloc_large_system_hash()
* make sizes overridable by boot parameters (mhash_entries=, mphash_entries=)
* switch mountpoint_hashtable from list_head to hlist_head

Cc: stable@vger.kernel.org
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>

Merge branch 'timers-urgent-for-linus' of git://git./linux/kernel/git/tip/tip

Pull timer fix from Ingo Molnar:
"A late breaking fix from John.  (The bug fixed has a hard lockup
  potential, but that was not observed, warnings were)"

* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  time: Revert to calling clock_was_set_delayed() while in irq context

Merge branch 'for-linus' of git://git./linux/kernel/git/sage/ceph-client

Pull Ceph fix from Sage Weil:
"This drops a bad assert that a few users have been hitting but we've
only recently been able to track down"

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/sage/ceph-client:
rbd: drop an unsafe assertion

Input: mousedev - fix race when creating mixed device

We should not be using static variable mousedev_mix in methods that can be
called before that singleton gets assigned. While at it let's add open and
close methods to mousedev structure so that we do not need to test if we
are dealing with multiplexor or normal device and simply call appropriate
method directly.

This fixes: https://bugzilla.kernel.org/show_bug.cgi?id=71551

Reported-by: GiulioDP <depasquale.giulio@gmail.com>
Tested-by: GiulioDP <depasquale.giulio@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Input: don't modify the id of ioctl-provided ff effect on upload failure

If a new (id == -1) ff effect was uploaded from userspace,
ff-core.c::input_ff_upload() will have assigned a positive number to the
new effect id. Currently, evdev.c::evdev_do_ioctl() will save this new id
to userspace, regardless of whether the upload succeeded or not.

On upload failure, this can be confusing because the dev->ff->effects[]
array will not contain an element at the index of that new effect id.

This patch fixes this by leaving the id unchanged after upload fails.

Note: Unfortunately applications should still expect changed effect id for
quite some time.

This has been discussed on:
http://www.mail-archive.com/linux-input@vger.kernel.org/msg08513.html
("ff-core effect id handling in case of a failed effect upload")

Suggested-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Elias Vanderstuyft <elias.vds@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

rbd: drop an unsafe assertion

Olivier Bonvalet reported having repeated crashes due to a failed
assertion he was hitting in rbd_img_obj_callback():

    Assertion failure in rbd_img_obj_callback() at line 2165:
rbd_assert(which >= img_request->next_completion);

With a lot of help from Olivier with reproducing the problem
we were able to determine the object and image requests had
already been completed (and often freed) at the point the
assertion failed.

There was a great deal of discussion on the ceph-devel mailing list
about this.  The problem only arose when there were two (or more)
object requests in an image request, and the problem was always
seen when the second request was being completed.

The problem is due to a race in the window between setting the
"done" flag on an object request and checking the image request's
next completion value.  When the first object request completes, it
checks to see if its successor request is marked "done", and if
so, that request is also completed.  In the process, the image
request's next_completion value is updated to reflect that both
the first and second requests are completed.  By the time the
second request is able to check the next_completion value, it
has been set to a value *greater* than its own "which" value,
which caused an assertion to fail.

Fix this problem by skipping over any completion processing
unless the completing object request is the next one expected.
Test only for inequality (not >=), and eliminate the bad
assertion.

Tested-by: Olivier Bonvalet <ob@daevel.fr>
Signed-off-by: Alex Elder <elder@linaro.org>
Reviewed-by: Sage Weil <sage@inktank.com>
Reviewed-by: Ilya Dryomov <ilya.dryomov@inktank.com>

Merge git://git./linux/kernel/git/davem/net

Pull networking fixes from David Miller:

1) We've discovered a common error in several networking drivers, they
    put VLAN offload features into ->vlan_features, which would suggest
    that they support offloading 2 or more levels of VLAN encapsulation.
    Not only do these devices not do that, but we don't have the
    infrastructure yet to handle that at all.

    Fixes from Vlad Yasevich.

2) Fix tcpdump crash with bridging and vlans, also from Vlad.

3) Some MAINTAINERS updates for random32 and bonding.

4) Fix late reseeds of prandom generator, from Sasha Levin.

5) Bridge doesn't handle stacked vlans properly, fix from Toshiaki
    Makita.

6) Fix deadlock in openvswitch, from Flavio Leitner.

7) get_timewait4_sock() doesn't report delay times correctly, fix from
    Eric Dumazet.

8) Duplicate address detection and addrconf verification need to run in
    contexts where RTNL can be obtained.  Move them to run from a
    workqueue.  From Hannes Frederic Sowa.

9) Fix route refcount leaking in ip tunnels, from Pravin B Shelar.

10) Don't return -EINTR from non-blocking recvmsg() on AF_UNIX sockets,
    from Eric Dumazet.

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (28 commits)
  vlan: Warn the user if lowerdev has bad vlan features.
  veth: Turn off vlan rx acceleration in vlan_features
  ifb: Remove vlan acceleration from vlan_features
  qlge: Do not propaged vlan tag offloads to vlans
  bridge: Fix crash with vlan filtering and tcpdump
  net: Account for all vlan headers in skb_mac_gso_segment
  MAINTAINERS: bonding: change email address
  MAINTAINERS: bonding: change email address
  ipv6: move DAD and addrconf_verify processing to workqueue
  tcp: fix get_timewait4_sock() delay computation on 64bit
  openvswitch: fix a possible deadlock and lockdep warning
  bridge: Fix handling stacked vlan tags
  bridge: Fix inabillity to retrieve vlan tags when tx offload is disabled
  vhost: validate vhost_get_vq_desc return value
  vhost: fix total length when packets are too short
  random32: avoid attempt to late reseed if in the middle of seeding
  random32: assign to network folks in MAINTAINERS
  net/mlx4_core: pass pci_device_id.driver_data to __mlx4_init_one during reset
  core, nfqueue, openvswitch: Orphan frags in skb_zerocopy and handle errors
  vlan: Set hard_header_len according to available acceleration
  ...

Merge branch 'vlan_offloads'

Vlad Yasevich says:

====================
Audit all drivers for correct vlan_features.

Some drivers set vlan acceleration features in vlan_features. This causes
issues with Q-in-Q/802.1ad configurations.

Audit all the drivers for correct vlan_features. Fix broken ones.
Add a warning to vlan code to help catch future offenders.
====================

Signed-off-by: David S. Miller <davem@davemloft.net>

vlan: Warn the user if lowerdev has bad vlan features.

Some drivers incorrectly assign vlan acceleration features to
vlan_features thus causing issues for Q-in-Q vlan configurations.
Warn the user of such cases.

Signed-off-by: Vlad Yasevich <vyasevic@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

veth: Turn off vlan rx acceleration in vlan_features

For completeness, turn off vlan rx acceleration in vlan_features so
that it doesn't show up on q-in-q setups.

Signed-off-by: Vlad Yasevich <vyasevic@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

ifb: Remove vlan acceleration from vlan_features

Do not include vlan acceleration features in vlan_features as that
precludes correct Q-in-Q operation.

Signed-off-by: Vlad Yasevich <vyasevic@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

qlge: Do not propaged vlan tag offloads to vlans

qlge driver turns off NETIF_F_HW_CTAG_FILTER, but forgets to
turn off HW_CTAG_TX and HW_CTAG_RX on vlan devices. With the
current settings, q-in-q will only generate a single vlan header.
Remember to mask off CTAG_TX and CTAG_RX features in vlan_features.

CC: Shahed Shaikh <shahed.shaikh@qlogic.com>
CC: Jitendra Kalsaria <jitendra.kalsaria@qlogic.com>
CC: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: Vlad Yasevich <vyasevic@redhat.com>
Acked-by: Jitendra Kalsaria <jitendra.kalsaria@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

bridge: Fix crash with vlan filtering and tcpdump

When the vlan filtering is enabled on the bridge, but
the filter is not configured on the bridge device itself,
running tcpdump on the bridge device will result in a
an Oops with NULL pointer dereference.  The reason
is that br_pass_frame_up() will bypass the vlan
check because promisc flag is set.  It will then try
to get the table pointer and process the packet based
on the table.  Since the table pointer is NULL, we oops.
Catch this special condition in br_handle_vlan().

Reported-by: Toshiaki Makita <makita.toshiaki@lab.ntt.co.jp>
CC: Toshiaki Makita <makita.toshiaki@lab.ntt.co.jp>
Signed-off-by: Vlad Yasevich <vyasevic@redhat.com>
Acked-by: Toshiaki Makita <makita.toshiaki@lab.ntt.co.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: Account for all vlan headers in skb_mac_gso_segment

skb_network_protocol() already accounts for multiple vlan
headers that may be present in the skb.  However, skb_mac_gso_segment()
doesn't know anything about it and assumes that skb->mac_len
is set correctly to skip all mac headers.  That may not
always be the case.  If we are simply forwarding the packet (via
bridge or macvtap), all vlan headers may not be accounted for.

A simple solution is to allow skb_network_protocol to return
the vlan depth it has calculated.  This way skb_mac_gso_segment
will correctly skip all mac headers.

Signed-off-by: Vlad Yasevich <vyasevic@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

MAINTAINERS: bonding: change email address

Signed-off-by: Veaceslav Falico <vfalico@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

MAINTAINERS: bonding: change email address

Update my email address.

Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge branch 'akpm' (patches from Andrew Morton)

Merge two fixes from Andrew Morton:
"The x86 fix should come from x86 guys but they appear to be
  conferencing or otherwise distracted.

  The ocfs2 fix is a bit of a mess - the code runs into an immediate
  NULL deref and we're trying to work out how this got through test and
  review, but we haven't heard from Goldwyn in the past few days.
  Sasha's patch fixes the oops, but the feature as a whole is probably
  broken.  So this is a stopgap for 3.14 - I'll aim to get the real
  fixes into 3.14.x"

* emailed patches from Andrew Morton akpm@linux-foundation.org>:
  x86: fix boot on uniprocessor systems
  ocfs2: check if cluster name exists before deref

x86: fix boot on uniprocessor systems

On x86 uniprocessor systems topology_physical_package_id() returns -1
which causes rapl_cpu_prepare() to leave rapl_pmu variable uninitialized
which leads to GPF in rapl_pmu_init().

See arch/x86/kernel/cpu/perf_event_intel_rapl.c.

It turns out that physical_package_id and core_id can actually be
retreived for uniprocessor systems too. Enabling them also fixes
rapl_pmu code.

Signed-off-by: Artem Fetishev <artem_fetishev@epam.com>
Cc: Stephane Eranian <eranian@google.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

ocfs2: check if cluster name exists before deref

Commit c74a3bdd9b52 ("ocfs2: add clustername to cluster connection") is
trying to strlcpy a string which was explicitly passed as NULL in the
very same patch, triggering a NULL ptr deref.

  BUG: unable to handle kernel NULL pointer dereference at           (null)
  IP: strlcpy (lib/string.c:388 lib/string.c:151)
  CPU: 19 PID: 19426 Comm: trinity-c19 Tainted: G        W     3.14.0-rc7-next-20140325-sasha-00014-g9476368-dirty #274
  RIP:  strlcpy (lib/string.c:388 lib/string.c:151)
  Call Trace:
   ocfs2_cluster_connect (fs/ocfs2/stackglue.c:350)
   ocfs2_cluster_connect_agnostic (fs/ocfs2/stackglue.c:396)
   user_dlm_register (fs/ocfs2/dlmfs/userdlm.c:679)
   dlmfs_mkdir (fs/ocfs2/dlmfs/dlmfs.c:503)
   vfs_mkdir (fs/namei.c:3467)
   SyS_mkdirat (fs/namei.c:3488 fs/namei.c:3472)
   tracesys (arch/x86/kernel/entry_64.S:749)

akpm: this patch probably disables the feature.  A temporary thing to
avoid triviel oopses.

Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
Cc: Goldwyn Rodrigues <rgoldwyn@suse.com>
Cc: Mark Fasheh <mfasheh@suse.de>
Cc: Joel Becker <jlbec@evilplan.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

ipv6: move DAD and addrconf_verify processing to workqueue

addrconf_join_solict and addrconf_join_anycast may cause actions which
need rtnl locked, especially on first address creation.

A new DAD state is introduced which defers processing of the initial
DAD processing into a workqueue.

To get rtnl lock we need to push the code paths which depend on those
calls up to workqueues, specifically addrconf_verify and the DAD
processing.

(v2)
addrconf_dad_failure needs to be queued up to the workqueue, too. This
patch introduces a new DAD state and stop the DAD processing in the
workqueue (this is because of the possible ipv6_del_addr processing
which removes the solicited multicast address from the device).

addrconf_verify_lock is removed, too. After the transition it is not
needed any more.

As we are not processing in bottom half anymore we need to be a bit more
careful about disabling bottom half out when we lock spin_locks which are also
used in bh.

Relevant backtrace:
[  541.030090] RTNL: assertion failed at net/core/dev.c (4496)
[  541.031143] CPU: 0 PID: 0 Comm: swapper/0 Tainted: G           O 3.10.33-1-amd64-vyatta #1
[  541.031145] Hardware name: Bochs Bochs, BIOS Bochs 01/01/2007
[  541.031146]  ffffffff8148a9f0 000000000000002f ffffffff813c98c1 ffff88007c4451f8
[  541.031148]  0000000000000000 0000000000000000 ffffffff813d3540 ffff88007fc03d18
[  541.031150]  0000880000000006 ffff88007c445000 ffffffffa0194160 0000000000000000
[  541.031152] Call Trace:
[  541.031153]  <IRQ>  [<ffffffff8148a9f0>] ? dump_stack+0xd/0x17
[  541.031180]  [<ffffffff813c98c1>] ? __dev_set_promiscuity+0x101/0x180
[  541.031183]  [<ffffffff813d3540>] ? __hw_addr_create_ex+0x60/0xc0
[  541.031185]  [<ffffffff813cfe1a>] ? __dev_set_rx_mode+0xaa/0xc0
[  541.031189]  [<ffffffff813d3a81>] ? __dev_mc_add+0x61/0x90
[  541.031198]  [<ffffffffa01dcf9c>] ? igmp6_group_added+0xfc/0x1a0 [ipv6]
[  541.031208]  [<ffffffff8111237b>] ? kmem_cache_alloc+0xcb/0xd0
[  541.031212]  [<ffffffffa01ddcd7>] ? ipv6_dev_mc_inc+0x267/0x300 [ipv6]
[  541.031216]  [<ffffffffa01c2fae>] ? addrconf_join_solict+0x2e/0x40 [ipv6]
[  541.031219]  [<ffffffffa01ba2e9>] ? ipv6_dev_ac_inc+0x159/0x1f0 [ipv6]
[  541.031223]  [<ffffffffa01c0772>] ? addrconf_join_anycast+0x92/0xa0 [ipv6]
[  541.031226]  [<ffffffffa01c311e>] ? __ipv6_ifa_notify+0x11e/0x1e0 [ipv6]
[  541.031229]  [<ffffffffa01c3213>] ? ipv6_ifa_notify+0x33/0x50 [ipv6]
[  541.031233]  [<ffffffffa01c36c8>] ? addrconf_dad_completed+0x28/0x100 [ipv6]
[  541.031241]  [<ffffffff81075c1d>] ? task_cputime+0x2d/0x50
[  541.031244]  [<ffffffffa01c38d6>] ? addrconf_dad_timer+0x136/0x150 [ipv6]
[  541.031247]  [<ffffffffa01c37a0>] ? addrconf_dad_completed+0x100/0x100 [ipv6]
[  541.031255]  [<ffffffff8105313a>] ? call_timer_fn.isra.22+0x2a/0x90
[  541.031258]  [<ffffffffa01c37a0>] ? addrconf_dad_completed+0x100/0x100 [ipv6]

Hunks and backtrace stolen from a patch by Stephen Hemminger.

Reported-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

tcp: fix get_timewait4_sock() delay computation on 64bit

It seems I missed one change in get_timewait4_sock() to compute
the remaining time before deletion of IPV4 timewait socket.

This could result in wrong output in /proc/net/tcp for tm->when field.

Fixes: 96f817fedec4 ("tcp: shrink tcp6_timewait_sock by one cache line")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

openvswitch: fix a possible deadlock and lockdep warning

There are two problematic situations.

A deadlock can happen when is_percpu is false because it can get
interrupted while holding the spinlock. Then it executes
ovs_flow_stats_update() in softirq context which tries to get
the same lock.

The second sitation is that when is_percpu is true, the code
correctly disables BH but only for the local CPU, so the
following can happen when locking the remote CPU without
disabling BH:

       CPU#0                            CPU#1
  ovs_flow_stats_get()
   stats_read()
+->spin_lock remote CPU#1        ovs_flow_stats_get()
|  <interrupted>                  stats_read()
|  ...                       +-->  spin_lock remote CPU#0
|                            |     <interrupted>
|  ovs_flow_stats_update()   |     ...
|   spin_lock local CPU#0 <--+     ovs_flow_stats_update()
+---------------------------------- spin_lock local CPU#1

This patch disables BH for both cases fixing the deadlocks.
Acked-by: Jesse Gross <jesse@nicira.com>
=================================
[ INFO: inconsistent lock state ]
3.14.0-rc8-00007-g632b06a #1 Tainted: G          I
---------------------------------
inconsistent {SOFTIRQ-ON-W} -> {IN-SOFTIRQ-W} usage.
swapper/0/0 [HC0[0]:SC1[5]:HE1:SE0] takes:
(&(&cpu_stats->lock)->rlock){+.?...}, at: [<ffffffffa05dd8a1>] ovs_flow_stats_update+0x51/0xd0 [openvswitch]
{SOFTIRQ-ON-W} state was registered at:
[<ffffffff810f973f>] __lock_acquire+0x68f/0x1c40
[<ffffffff810fb4e2>] lock_acquire+0xa2/0x1d0
[<ffffffff817d8d9e>] _raw_spin_lock+0x3e/0x80
[<ffffffffa05dd9e4>] ovs_flow_stats_get+0xc4/0x1e0 [openvswitch]
[<ffffffffa05da855>] ovs_flow_cmd_fill_info+0x185/0x360 [openvswitch]
[<ffffffffa05daf05>] ovs_flow_cmd_build_info.constprop.27+0x55/0x90 [openvswitch]
[<ffffffffa05db41d>] ovs_flow_cmd_new_or_set+0x4dd/0x570 [openvswitch]
[<ffffffff816c245d>] genl_family_rcv_msg+0x1cd/0x3f0
[<ffffffff816c270e>] genl_rcv_msg+0x8e/0xd0
[<ffffffff816c0239>] netlink_rcv_skb+0xa9/0xc0
[<ffffffff816c0798>] genl_rcv+0x28/0x40
[<ffffffff816bf830>] netlink_unicast+0x100/0x1e0
[<ffffffff816bfc57>] netlink_sendmsg+0x347/0x770
[<ffffffff81668e9c>] sock_sendmsg+0x9c/0xe0
[<ffffffff816692d9>] ___sys_sendmsg+0x3a9/0x3c0
[<ffffffff8166a911>] __sys_sendmsg+0x51/0x90
[<ffffffff8166a962>] SyS_sendmsg+0x12/0x20
[<ffffffff817e3ce9>] system_call_fastpath+0x16/0x1b
irq event stamp: 1740726
hardirqs last  enabled at (1740726): [<ffffffff8175d5e0>] ip6_finish_output2+0x4f0/0x840
hardirqs last disabled at (1740725): [<ffffffff8175d59b>] ip6_finish_output2+0x4ab/0x840
softirqs last  enabled at (1740674): [<ffffffff8109be12>] _local_bh_enable+0x22/0x50
softirqs last disabled at (1740675): [<ffffffff8109db05>] irq_exit+0xc5/0xd0

other info that might help us debug this:
Possible unsafe locking scenario:

       CPU0
       ----
  lock(&(&cpu_stats->lock)->rlock);
  <Interrupt>
    lock(&(&cpu_stats->lock)->rlock);

*** DEADLOCK ***

5 locks held by swapper/0/0:
#0:  (((&ifa->dad_timer))){+.-...}, at: [<ffffffff810a7155>] call_timer_fn+0x5/0x320
#1:  (rcu_read_lock){.+.+..}, at: [<ffffffff81788a55>] mld_sendpack+0x5/0x4a0
#2:  (rcu_read_lock_bh){.+....}, at: [<ffffffff8175d149>] ip6_finish_output2+0x59/0x840
#3:  (rcu_read_lock_bh){.+....}, at: [<ffffffff8168ba75>] __dev_queue_xmit+0x5/0x9b0
#4:  (rcu_read_lock){.+.+..}, at: [<ffffffffa05e41b5>] internal_dev_xmit+0x5/0x110 [openvswitch]

stack backtrace:
CPU: 0 PID: 0 Comm: swapper/0 Tainted: G          I  3.14.0-rc8-00007-g632b06a #1
Hardware name:                  /DX58SO, BIOS SOX5810J.86A.5599.2012.0529.2218 05/29/2012
0000000000000000 0fcf20709903df0c ffff88042d603808 ffffffff817cfe3c
ffffffff81c134c0 ffff88042d603858 ffffffff817cb6da 0000000000000005
ffffffff00000001 ffff880400000000 0000000000000006 ffffffff81c134c0
Call Trace:
<IRQ>  [<ffffffff817cfe3c>] dump_stack+0x4d/0x66
[<ffffffff817cb6da>] print_usage_bug+0x1f4/0x205
[<ffffffff810f7f10>] ? check_usage_backwards+0x180/0x180
[<ffffffff810f8963>] mark_lock+0x223/0x2b0
[<ffffffff810f96d3>] __lock_acquire+0x623/0x1c40
[<ffffffff810f5707>] ? __lock_is_held+0x57/0x80
[<ffffffffa05e26c6>] ? masked_flow_lookup+0x236/0x250 [openvswitch]
[<ffffffff810fb4e2>] lock_acquire+0xa2/0x1d0
[<ffffffffa05dd8a1>] ? ovs_flow_stats_update+0x51/0xd0 [openvswitch]
[<ffffffff817d8d9e>] _raw_spin_lock+0x3e/0x80
[<ffffffffa05dd8a1>] ? ovs_flow_stats_update+0x51/0xd0 [openvswitch]
[<ffffffffa05dd8a1>] ovs_flow_stats_update+0x51/0xd0 [openvswitch]
[<ffffffffa05dcc64>] ovs_dp_process_received_packet+0x84/0x120 [openvswitch]
[<ffffffff810f93f7>] ? __lock_acquire+0x347/0x1c40
[<ffffffffa05e3bea>] ovs_vport_receive+0x2a/0x30 [openvswitch]
[<ffffffffa05e4218>] internal_dev_xmit+0x68/0x110 [openvswitch]
[<ffffffffa05e41b5>] ? internal_dev_xmit+0x5/0x110 [openvswitch]
[<ffffffff8168b4a6>] dev_hard_start_xmit+0x2e6/0x8b0
[<ffffffff8168be87>] __dev_queue_xmit+0x417/0x9b0
[<ffffffff8168ba75>] ? __dev_queue_xmit+0x5/0x9b0
[<ffffffff8175d5e0>] ? ip6_finish_output2+0x4f0/0x840
[<ffffffff8168c430>] dev_queue_xmit+0x10/0x20
[<ffffffff8175d641>] ip6_finish_output2+0x551/0x840
[<ffffffff8176128a>] ? ip6_finish_output+0x9a/0x220
[<ffffffff8176128a>] ip6_finish_output+0x9a/0x220
[<ffffffff8176145f>] ip6_output+0x4f/0x1f0
[<ffffffff81788c29>] mld_sendpack+0x1d9/0x4a0
[<ffffffff817895b8>] mld_send_initial_cr.part.32+0x88/0xa0
[<ffffffff817691b0>] ? addrconf_dad_completed+0x220/0x220
[<ffffffff8178e301>] ipv6_mc_dad_complete+0x31/0x50
[<ffffffff817690d7>] addrconf_dad_completed+0x147/0x220
[<ffffffff817691b0>] ? addrconf_dad_completed+0x220/0x220
[<ffffffff8176934f>] addrconf_dad_timer+0x19f/0x1c0
[<ffffffff810a71e9>] call_timer_fn+0x99/0x320
[<ffffffff810a7155>] ? call_timer_fn+0x5/0x320
[<ffffffff817691b0>] ? addrconf_dad_completed+0x220/0x220
[<ffffffff810a76c4>] run_timer_softirq+0x254/0x3b0
[<ffffffff8109d47d>] __do_softirq+0x12d/0x480

Signed-off-by: Flavio Leitner <fbl@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

bridge: Fix handling stacked vlan tags

If a bridge with vlan_filtering enabled receives frames with stacked
vlan tags, i.e., they have two vlan tags, br_vlan_untag() strips not
only the outer tag but also the inner tag.

br_vlan_untag() is called only from br_handle_vlan(), and in this case,
it is enough to set skb->vlan_tci to 0 here, because vlan_tci has already
been set before calling br_handle_vlan().

Signed-off-by: Toshiaki Makita <makita.toshiaki@lab.ntt.co.jp>
Acked-by: Vlad Yasevich <vyasevic@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

bridge: Fix inabillity to retrieve vlan tags when tx offload is disabled

Bridge vlan code (br_vlan_get_tag()) assumes that all frames have vlan_tci
if they are tagged, but if vlan tx offload is manually disabled on bridge
device and frames are sent from vlan device on the bridge device, the tags
are embedded in skb->data and they break this assumption.
Extract embedded vlan tags and move them to vlan_tci at ingress.

Signed-off-by: Toshiaki Makita <makita.toshiaki@lab.ntt.co.jp>
Acked-by: Vlad Yasevich <vyasevic@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

vhost: validate vhost_get_vq_desc return value

vhost fails to validate negative error code
from vhost_get_vq_desc causing
a crash: we are using -EFAULT which is 0xfffffff2
as vector size, which exceeds the allocated size.

The code in question was introduced in commit
8dd014adfea6f173c1ef6378f7e5e7924866c923
vhost-net: mergeable buffers support

CVE-2014-0055

Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

vhost: fix total length when packets are too short

When mergeable buffers are disabled, and the
incoming packet is too large for the rx buffer,
get_rx_bufs returns success.

This was intentional in order for make recvmsg
truncate the packet and then handle_rx would
detect err != sock_len and drop it.

Unfortunately we pass the original sock_len to
recvmsg - which means we use parts of iov not fully
validated.

Fix this up by detecting this overrun and doing packet drop
immediately.

CVE-2014-0077

Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

random32: avoid attempt to late reseed if in the middle of seeding

Commit 4af712e8df ("random32: add prandom_reseed_late() and call when
nonblocking pool becomes initialized") has added a late reseed stage
that happens as soon as the nonblocking pool is marked as initialized.

This fails in the case that the nonblocking pool gets initialized
during __prandom_reseed()'s call to get_random_bytes(). In that case
we'd double back into __prandom_reseed() in an attempt to do a late
reseed - deadlocking on 'lock' early on in the boot process.

Instead, just avoid even waiting to do a reseed if a reseed is already
occuring.

Fixes: 4af712e8df99 ("random32: add prandom_reseed_late() and call when nonblocking pool becomes initialized")
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge branch 'for-linus' of git://git./linux/kernel/git/dtor/input

Pull input subsystem fixes from Dmitry Torokhov:
"Updates to Synaptics touchpad to better cope with devices in Lenovo
  laptops, and a couple more fixes"

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
  Input: synaptics - add manual min/max quirk for ThinkPad X240
  Input: synaptics - add manual min/max quirk
  Input: cypress_ps2 - don't report as a button pads
  Input: da9052_onkey - use correct register bit for key status
  Input: adp5588-keys - get value from data out when dir is out

random32: assign to network folks in MAINTAINERS

lib/random32.c was split out of the network code and is de-facto
still maintained by the almighty net/ gods.

Make it a bit more official so that people who aren't aware of
that know where to send their patches.

Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge branch 'drm-fixes' of git://people.freedesktop.org/~airlied/linux

Pull drm fixes from Dave Airlie:
"I didn't want these to wait for stable cycle.

  The nouveau and radeon ones are the same problem, where the runtime pm
  stuff broke non-runtime pm managed secondary GPUs.

  The udl fix is for an oops on unplug, and the i915 fix is for a
  regression on Sandybridge even though it may break haswell (regression
  wins)"

Daniel Vetter comments:
"My apologies for the i915 regression fumble, that thing somehow fell
  through the cracks here for almost half a year :( Imo that's more than
  enough flailing to just go ahead with the revert, and the re-broken
  hsw should get peoples attention ..."

* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
  drm/i915: Undo gtt scratch pte unmapping again
  drm/radeon: fix runtime suspend breaking secondary GPUs
  drm/nouveau: fail runtime pm properly.
  drm/udl: take reference to device struct for dma-bufs

Merge branch 'i2c/for-current' of git://git./linux/kernel/git/wsa/linux

Pull i2c build fix from Wolfram Sang:
"The build fix from my last request unveiled another build problem
which is fixed with this patch"

* 'i2c/for-current' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
i2c: cpm: Fix build by adding of_address.h and of_irq.h

Merge tag 'stable/for-linus-3.14-rc8-tag' of git://git./linux/kernel/git/xen/tip

Pull Xen bugfixes from David Vrabel:
"Fix two bugs that cause x86 PV guest crashes.

  1. Ballooning a 32-bit guest would eventually crash it.

  2. Revert a broken fix for a regression with NUMA_BALACING.  The bad
     fix caused PV guests to crash after migration.  This is not ideal
     but unpicking the madness that is _PAGE_NUMA == _PAGE_PROTNONE will
     take a while longer"

* tag 'stable/for-linus-3.14-rc8-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
  Revert "xen: properly account for _PAGE_NUMA during xen pte translations"
  xen/balloon: flush persistent kmaps in correct position

drm/i915/tv: fix gen4 composite s-video tv-out

This is *not* bisected, but the likely regression is

commit c35614380d5c956bfda20eab2755b2f5a7d6f1e7
Author: Zhao Yakui <yakui.zhao@intel.com>
Date: Tue Nov 24 09:48:48 2009 +0800

drm/i915: Don't set up the TV port if it isn't in the BIOS table.

The commit does not check for all TV device types that might be present
in the VBT, disabling TV out for the missing ones. Add composite
S-video.

Reported-and-tested-by: Matthew Khouzam <matthew.khouzam@gmail.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=73362
Cc: stable@vger.kernel.org
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

drm/i915: Split 64bit hexadecimal addresses to make them easier to read

Broadwell introduces large address spaces, greater than 32bits in width.
These require that we then store and print 64bit values. If we were to
zero pad them out to 16 hexadecimal places, we have to carefully count
the leading zeroes - which is easy to make a mistake. Conversely, if we
do not zero pad out to 16, but keep it padding to 8 hexadecimal places,
it is very easy to miss an address that is actually larger than 4GiB. A
suggested compromise is to insert a space between the upper and lower
dwords of the address so that we can continue with our accustom 32bit
parser. (Alternatively, we could do the equivalent in our userspace
decoder.)

Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

drm/i915: Broadwell expands ACTHD to 64bit

As Broadwell has an increased virtual address size, it requires more
than 32 bits to store offsets into its address space. This includes the
debug registers to track the current HEAD of the individual rings, which
may be anywhere within the per-process address spaces. In order to find
the full location, we need to read the high bits from a second register.
We then also need to expand our storage to keep track of the larger
address.

v2: Carefully read the two registers to catch wraparound between
the reads.
v3: Use a WARN_ON rather than loop indefinitely on an unstable
register read.

Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Ben Widawsky <benjamin.widawsky@intel.com>
Cc: Timo Aaltonen <tjaalton@ubuntu.com>
Cc: Tvrtko Ursulin <tvrtko.ursulin@linux.intel.com>
Reviewed-by: Ben Widawsky <ben@bwidawsk.net>
[danvet: Drop spurious hunk which conflicted.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

drm/i915/bdw: Implement Wa4x4STCOptimizationDisable:bdw

Not implementing this W/A can lead to hangs.

Cc: Ben Widawsky <benjamin.widawsky@intel.com>
Cc: Rafael Barbalho <rafael.barbalho@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Reviewed-by: Ben Widawsky <ben@bwidawsk.net>
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

drm/i915: Undo gtt scratch pte unmapping again

It apparently blows up on some machines. This functionally reverts

commit 828c79087cec61eaf4c76bb32c222fbe35ac3930
Author: Ben Widawsky <benjamin.widawsky@intel.com>
Date: Wed Oct 16 09:21:30 2013 -0700

drm/i915: Disable GGTT PTEs on GEN6+ suspend

Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=64841
Reported-and-Tested-by: Brad Jackson <bjackson0971@gmail.com>
Cc: stable@vger.kernel.org
Cc: Takashi Iwai <tiwai@suse.de>
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: Todd Previte <tprevite@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

drm/i915: Recompute WM when the cursor size changes

If the cursor width is changed, we may need to recompute our WM to
prevent untold flickering. We hope that the registers are flushed on the
same vblank to prevent underruns...

Cc: Damien Lespiau <damien.lespiau@intel.com>
Cc: Sagar Kamble <sagar.a.kamble@intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

drm/i915: Compute WM for current cursor size

Now that we can use different cursor size, we can not hardcode 64 pixels
as the cursor width anymore.

v2: Apply to 965gm/g4x paths as well

Cc: Damien Lespiau <damien.lespiau@intel.com>
Cc: Sagar Kamble <sagar.a.kamble@intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

drm/i915: Remove the enabling of VS_TIMER_DISPATCH bit in MI MODE reg

This patch Removes the VS_TIMER_DISPATCH bit enable in MI MODE reg for
platforms > Gen6.
VS_TIMER_DISPATCH bit enable was earlier required as a part of
WA 'WaTimedSingleVertexDispatch', which is now applicable only to
platforms < Gen7.

v2: Enhancing the scope of the patch to full Gen7 (Chris)

v3: Modifying the WA condition to the cover the applicable platforms,
and adding the WA name in comments. (Ville)

Signed-off-by: Akash Goel <akash.goel@intel.com>
Signed-off-by: Sourab Gupta <sourab.gupta@intel.com>
Tested-by: Chris Wilson <chris@chris-wilson.co.uk> # ivb, hsw -Chris
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

drm/i915: Track the enabled PM interrupts in dev_priv.

When we use different rps events for different platforms or due to wa,
we might end up needing this logic in a lot of places. Instead of
this let's use a variable in dev_priv to track the enabled PM
interrupts.

v2: Initialize pm_rps_events in intel_irq_init() (Ville).

Signed-off-by: Deepak S <deepak.s@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
[danvet: Frob the commit message a bit since the English was a bit too
garbled ;-) ]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

drm/i915: Fix initial pipe underrun state tracking

Since

commit 5c673b60a9b3b23486f4eda75c72e91d31d26a2b
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date: Fri Mar 7 20:34:46 2014 +0100

drm/i915: Don't enable display error interrupts from the start

we don't enable underrun interrupts any more at takeover time.
Unfortunately I've forgotten to also adjust the sw-side tracking.

Since the code assumes that disabled pipes have underrun reporting
enabled set the disable flag only on all pipes which are active at
takeover time. Without this underrun reporting wasn't enabled
correctly on the first modeset. Note that for fastboot this is another
piece of state that needs to be fixed up by enabling the underrung
reporting after watermarks have beend fixed up.

On ivb/hsw an additional effect of this regression was that also all
cpu crc reporting stopped working since the master error interrupt it
shared across all pipes and sources.

Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=76150
[danvet: Augment the code comment and polish the commit message a bit,
as discussed with Jani.]
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Tested-by: lu hua <huax.lu@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

drm/i915: fix up semaphore_waits_for

There's an entire pile of issues in here:

- Use the main RING_HEAD register, not ACTHD. ACTHD points at the gtt
  offset of the batch buffer when a batch is executed. Semaphores are
  always emitted to the main ring, so we always want to look at that.

- Mask the obtained HEAD pointer with the actual ring size, which is
  much smaller. Together with the above issue this resulted us in
  trying to dereference a pointer way outside of the ring mmio
  mapping. The resulting invalid access in interrupt context
  (hangcheck is executed from timers) lead to a full blown kernel
  panic. The fbcon panic handler then tried to frob our driver harder,
  resulting in a full machine hang at least on my snb here where I've
  stumbled over this.

- Handle ring wrapping correctly and be a bit more explicit about how
  many dwords we're scanning. We probably should also scan more than
  just 4 ...

- Space out some of teh computations for readability.

This reduces hard-hangs on my snb here. Mika and QA both say that it
doesn't completel remove them, but at least for me it's a clear
improvement in stability.

Cc: Mika Kuoppala <mika.kuoppala@intel.com>
Cc: Ben Widawsky <ben@bwidawsk.net>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
References: https://bugs.freedesktop.org/show_bug.cgi?id=74100
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

drm/i915: add locking to fixed panel edid probing

With the recent addition of locking checks in

commit 62ff94a5492175759546f8bc61383189d6b49122
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
AuthorDate: Thu Jan 23 22:18:47 2014 +0100

drm/crtc-helper: remove LOCKING from kerneldoc

drm_add_edid_modes started to WARN about the mode_config.mutex not
being held in the lvds and dp initialization code.

Now since this is init code locking is fairly redudant if it wouldn't
be for the drm core registering sysfs files a bit early. And the
locking WARNINGs nicely enforce that indeed all access to the mode
lists are properly protected. And a full audit shows that only i915
and gma500 touch the modes lists at init time.

Hence I've opted to wrap up this entire mode detection sequence for
fixed panels with the mode_config mutex for both lvds and edp outputs.

Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

Input: synaptics - add manual min/max quirk for ThinkPad X240

This extends Benjamin Tissoires manual min/max quirk table with support for
the ThinkPad X240.

Cc: stable@vger.kernel.org
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Input: synaptics - add manual min/max quirk

The new Lenovo Haswell series (-40's) contains a new Synaptics touchpad.
However, these new Synaptics devices report bad axis ranges.
Under Windows, it is not a problem because the Windows driver uses RMI4
over SMBus to talk to the device. Under Linux, we are using the PS/2
fallback interface and it occurs the reported ranges are wrong.

Of course, it would be too easy to have only one range for the whole
series, each touchpad seems to be calibrated in a different way.

We can not use SMBus to get the actual range because I suspect the firmware
will switch into the SMBus mode and stop talking through PS/2 (this is the
case for hybrid HID over I2C / PS/2 Synaptics touchpads).

So as a temporary solution (until RMI4 land into upstream), start a new
list of quirks with the min/max manually set.

Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
CC: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

time: Revert to calling clock_was_set_delayed() while in irq context

In commit 47a1b796306356f35 ("tick/timekeeping: Call
update_wall_time outside the jiffies lock"), we moved to calling
clock_was_set() due to the fact that we were no longer holding
the timekeeping or jiffies lock.

However, there is still the problem that clock_was_set()
triggers an IPI, which cannot be done from the timer's hard irq
context, and will generate WARN_ON warnings.

Apparently in my earlier testing, I'm guessing I didn't bump the
dmesg log level, so I somehow missed the WARN_ONs.

Thus we need to revert back to calling clock_was_set_delayed().

Signed-off-by: John Stultz <john.stultz@linaro.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Link: http://lkml.kernel.org/r/1395963049-11923-1-git-send-email-john.stultz@linaro.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>

drm/i915: Undo gtt scratch pte unmapping again

It apparently blows up on some machines. This functionally reverts

commit 828c79087cec61eaf4c76bb32c222fbe35ac3930
Author: Ben Widawsky <benjamin.widawsky@intel.com>
Date: Wed Oct 16 09:21:30 2013 -0700

drm/i915: Disable GGTT PTEs on GEN6+ suspend

Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=64841
Reported-and-Tested-by: Brad Jackson <bjackson0971@gmail.com>
Cc: stable@vger.kernel.org
Cc: Takashi Iwai <tiwai@suse.de>
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: Todd Previte <tprevite@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Dave Airlie <airlied@redhat.com>

drm/radeon: fix runtime suspend breaking secondary GPUs

Same fix as for nouveau, when we fail with EINVAL, subsequent
gets fail hard, causing the device not to open.

Signed-off-by: Dave Airlie <airlied@redhat.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>

net/mlx4_core: pass pci_device_id.driver_data to __mlx4_init_one during reset

The second parameter of __mlx4_init_one() is used to identify whether the
pci_dev is a PF or VF. Currently, when it is invoked in mlx4_pci_slot_reset()
this information is missed.

This patch match the pci_dev with mlx4_pci_table and passes the
pci_device_id.driver_data to __mlx4_init_one() in mlx4_pci_slot_reset().

Signed-off-by: Wei Yang <weiyang@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

core, nfqueue, openvswitch: Orphan frags in skb_zerocopy and handle errors

skb_zerocopy can copy elements of the frags array between skbs, but it doesn't
orphan them. Also, it doesn't handle errors, so this patch takes care of that
as well, and modify the callers accordingly. skb_tx_error() is also added to
the callers so they will signal the failed delivery towards the creator of the
skb.

Signed-off-by: Zoltan Kiss <zoltan.kiss@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

vlan: Set hard_header_len according to available acceleration

Currently, if the card supports CTAG acceleration we do not
account for the vlan header even if we are configuring an
8021AD vlan. This may not be best since we'll do software
tagging for 8021AD which will cause data copy on skb head expansion
Configure the length based on available hw offload capabilities and
vlan protocol.

CC: Patrick McHardy <kaber@trash.net>
Signed-off-by: Vlad Yasevich <vyasevic@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

usbnet: include wait queue head in device structure

This fixes a race which happens by freeing an object on the stack.
Quoting Julius:
> The issue is
> that it calls usbnet_terminate_urbs() before that, which temporarily
> installs a waitqueue in dev->wait in order to be able to wait on the
> tasklet to run and finish up some queues. The waiting itself looks
> okay, but the access to 'dev->wait' is totally unprotected and can
> race arbitrarily. I think in this case usbnet_bh() managed to succeed
> it's dev->wait check just before usbnet_terminate_urbs() sets it back
> to NULL. The latter then finishes and the waitqueue_t structure on its
> stack gets overwritten by other functions halfway through the
> wake_up() call in usbnet_bh().

The fix is to just not allocate the data structure on the stack.
As dev->wait is abused as a flag it also takes a runtime PM change
to fix this bug.

Signed-off-by: Oliver Neukum <oneukum@suse.de>
Reported-by: Grant Grundler <grundler@google.com>
Tested-by: Grant Grundler <grundler@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

virtio-net: correct error handling of virtqueue_kick()

Current error handling of virtqueue_kick() was wrong in two places:
- The skb were freed immediately when virtqueue_kick() fail during
  xmit. This may lead double free since the skb was not detached from
  the virtqueue.
- try_fill_recv() returns false when virtqueue_kick() fail. This will
  lead unnecessary rescheduling of refill work.

Actually, it's safe to just ignore the kick failure in those two
places. So this patch fixes this by partially revert commit
67975901183799af8e93ec60e322f9e2a1940b9b.

Fixes 67975901183799af8e93ec60e322f9e2a1940b9b
(virtio_net: verify if virtqueue_kick() succeeded).

Cc: Heinz Graalfs <graalfs@linux.vnet.ibm.com>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

vfs: Allocate anon_inode_inode in anon_inode_init()

Currently we allocated anon_inode_inode in anon_inodefs_mount. This is
somewhat fragile as if that function ever gets called again, it will
overwrite anon_inode_inode pointer. So move the initialization of
anon_inode_inode to anon_inode_init().

Signed-off-by: Jan Kara <jack@suse.cz>
[ Further simplified on suggestion from Dave Jones ]
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

drm/nouveau: fail runtime pm properly.

If we were on a non-optimus device, we'd return -EINVAL, this would
lead to the over engineered runtime pm system to go into an error
state, subsequent get_sync's would fail, so we'd never be able
to open the device again.

(like really get_sync shouldn't fail if the device isn't powered
down).

Signed-off-by: Dave Airlie <airlied@redhat.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>

drm/udl: take reference to device struct for dma-bufs

this stops the device from being deleted before all the dma-bufs
on it are freed, this fixes an oops when you unplug a udl device while
it has imported a buffer from another device.

Signed-off-by: Dave Airlie <airlied@redhat.com>

net: unix: non blocking recvmsg() should not return -EINTR

Some applications didn't expect recvmsg() on a non blocking socket
could return -EINTR. This possibility was added as a side effect
of commit b3ca9b02b00704 ("net: fix multithreaded signal handling in
unix recv routines").

To hit this bug, you need to be a bit unlucky, as the u->readlock
mutex is usually held for very small periods.

Fixes: b3ca9b02b00704 ("net: fix multithreaded signal handling in unix recv routines")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Rainer Weikusat <rweikusat@mobileactivedefense.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge branch 'mvneta'

Thomas Petazzoni says:

====================
net: mvneta: fix usage as a module

The following set of two patches fix the usage of the mvneta driver
when built as a module, and used in RGMII configurations. It is
somewhat similar to a previous fix that was made by Arnaud Patard, but
which was limited to SGMII configurations.
====================

Signed-off-by: David S. Miller <davem@davemloft.net>

net: mvneta: use devm_ioremap_resource() instead of of_iomap()

The mvneta driver currently uses of_iomap(), which has two drawbacks:
it doesn't request the resource, and it isn't devm-style so some error
handling is needed.

This commit switches to use devm_ioremap_resource() instead, which
automatically requests the resource (so the I/O registers region shows
up properly in /proc/iomem), and also is devm-style, which allows to
get rid of some error handling to unmap the I/O registers region.

Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: mvneta: fix usage as a module on RGMII configurations

Commit 5445eaf309ff ('mvneta: Try to fix mvneta when compiled as
module') fixed the mvneta driver to make it work properly when loaded
as a module in SGMII configuration, which was tested successful by the
author on the Armada XP OpenBlocks AX3, which uses SGMII.

However, it turns out that the Armada XP GP, which uses RGMII, is
affected by a similar problem: its SERDES configuration is lost when
mvneta is loaded as a module, because this configuration is set by the
bootloader, and then lost because the clock is gated by the clock
framework until the mvneta driver is loaded again and the clock is
re-enabled.

However, it turns out that for the RGMII case, setting the SERDES
configuration is not sufficient: the PCS enable bit in the
MVNETA_GMAC_CTRL_2 register must also be set, like in the SGMII
configuration.

Therefore, this commit reworks the SGMII/RGMII initialization: the
only difference between the two now is a different SERDES
configuration, all the rest is identical.

In detail, to achieve this, the commit:

* Renames MVNETA_SGMII_SERDES_CFG to MVNETA_SERDES_CFG because it is
   not specific to SGMII, but also used on RGMII configurations.

* Adds a MVNETA_RGMII_SERDES_PROTO definition, that must be used as
   the MVNETA_SERDES_CFG value in RGMII configurations.

* Removes the mvneta_gmac_rgmii_set() and mvneta_port_sgmii_config()
   functions, and instead directly do the SGMII/RGMII configuration in
   mvneta_port_up(), from where those functions where called. It is
   worth mentioning that mvneta_gmac_rgmii_set() had an 'enable'
   parameter that was always passed as '1', so it was pretty useless.

* Reworks the mvneta_port_up() function to set the MVNETA_SERDES_CFG
   register to the appropriate value depending on the RGMII vs. SGMII
   configuration. It also unconditionally set the PCS_ENABLE bit (was
   already done for SGMII, but is now also needed for RGMII), and sets
   the PORT_RGMII bit (which was already done for both SGMII and
   RGMII).

This commit was successfully tested with mvneta compiled as a module,
on both the OpenBlocks AX3 (SGMII configuration) and the Armada XP GP
(RGMII configuration).

Reported-by: Steve McIntyre <steve@einval.com>
Cc: stable@vger.kernel.org # 3.11.x: 5445eaf309ff mvneta: Try to fix mvneta when compiled as module
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: mvneta: rename MVNETA_GMAC2_PSC_ENABLE to MVNETA_GMAC2_PCS_ENABLE

Bit 3 of the MVNETA_GMAC_CTRL_2 is actually used to enable the PCS,
not the PSC: there was a typo in the name of the define, which this
commit fixes.

Cc: stable@vger.kernel.org
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Input: cypress_ps2 - don't report as a button pads

The cypress PS/2 trackpad models supported by the cypress_ps2 driver
emulate BTN_RIGHT events in firmware based on the finger position, as part
of this no motion events are sent when the finger is in the button area.

The INPUT_PROP_BUTTONPAD property is there to indicate to userspace that
BTN_RIGHT events should be emulated in userspace, which is not necessary
in this case.

When INPUT_PROP_BUTTONPAD is advertised userspace will wait for a motion
event before propagating the button event higher up the stack, as it needs
current abs x + y data for its BTN_RIGHT emulation. Since in the
cypress_ps2 pads don't report motion events in the button area, this means
that clicks in the button area end up being ignored, so
INPUT_PROP_BUTTONPAD actually causes problems for these touchpads, and
removing it fixes:

https://bugs.freedesktop.org/show_bug.cgi?id=76341

Reported-by: Adam Williamson <awilliam@redhat.com>
Tested-by: Adam Williamson <awilliam@redhat.com>
Reviewed-by: Peter Hutterer <peter.hutterer@who-t.net>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

tg3: Do not include vlan acceleration features in vlan_features

Including hardware acceleration features in vlan_features breaks
stacked vlans (Q-in-Q) by marking the bottom vlan interface as
capable of acceleration. This causes one of the tags to be lost
and the packets are sent with a sing vlan header.

CC: Nithin Nayak Sujir <nsujir@broadcom.com>
CC: Michael Chan <mchan@broadcom.com>
Signed-off-by: Vlad Yasevich <vyasevic@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

ip_tunnel: Fix dst ref-count.

Commit 10ddceb22ba (ip_tunnel:multicast process cause panic due
to skb->_skb_refdst NULL pointer) removed dst-drop call from
ip-tunnel-recv.

Following commit reintroduce dst-drop and fix the original bug by
checking loopback packet before releasing dst.
Original bug: https://bugzilla.kernel.org/show_bug.cgi?id=70681

CC: Xin Long <lucien.xin@gmail.com>
Signed-off-by: Pravin B Shelar <pshelar@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge tag 'trace-fixes-v3.14-rc7-v2' of git://git./linux/kernel/git/rostedt/linux-trace

Pull tracing fix from Steven Rostedt:
"While on my flight to Linux Collaboration Summit, I was working on my
  slides for the event trigger tutorial.  I booted a 3.14-rc7 kernel to
  perform what I wanted to teach and cut and paste it into my slides.
  When I tried the traceon event trigger with a condition attached to it
  (turns tracing on only if a field of the trigger event matches a
  condition set by the user), nothing happened.  Tracing would not turn
  on.  I stopped working on my presentation in order to find what was
  wrong.

  It ended up being the way trace event triggers work when they have
  conditions.  Instead of copying the fields, the condition code just
  looks at the fields that were copied into the ring buffer.  This works
  great, unless tracing is off.  That's because when the event is
  reserved on the ring buffer, the ring buffer returns a NULL pointer,
  this tells the tracing code that the ring buffer is disabled.  This
  ends up being a problem for the traceon trigger if it is using this
  information to check its condition.

  Luckily the code that checks if tracing is on returns the ring buffer
  to use (because the ring buffer is determined by the event file also
  passed to that field).  I was able to easily solve this bug by
  checking in that helper function if the returned ring buffer entry is
  NULL, and if so, also check the file flag if it has a trace event
  trigger condition, and if so, to pass back a temp ring buffer to use.
  This will allow the trace event trigger condition to still test the
  event fields, but nothing will be recorded"

* tag 'trace-fixes-v3.14-rc7-v2' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace:
  tracing: Fix traceon trigger condition to actually turn tracing on

tracing: Fix traceon trigger condition to actually turn tracing on

While working on my tutorial for 2014 Linux Collaboration Summit
I found that the traceon trigger did not work when conditions were
used. The other triggers worked fine though. Looking into it, it
is because of the way the triggers use the ring buffer to store
the fields it will use for the condition. But if tracing is off, nothing
is stored in the buffer, and the tracepoint exits before calling the
trigger to test the condition. This is fine for all the triggers that
only work when tracing is on, but for traceon trigger that is to
work when tracing is off, nothing happens.

The fix is simple, just use a temp ring buffer to record the event
if tracing is off and the event has a trace event conditional trigger
enabled. The rest of the tracepoint code will work just fine, but
the tracepoint wont be recorded in the other buffers.

Cc: Tom Zanussi <tom.zanussi@linux.intel.com>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>

fs: remove now stale label in anon_inode_init()

The previous commit removed the register_filesystem() call and the
associated error handling, but left the label for the error path that no
longer exists. Remove that too.

Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

fs: Avoid userspace mounting anon_inodefs filesystem

anon_inodefs filesystem is a kernel internal filesystem userspace
shouldn't mess with. Remove registration of it so userspace cannot
even try to mount it (which would fail anyway because the filesystem is
MS_NOUSER).

This fixes an oops triggered by trinity when it tried mounting
anon_inodefs which overwrote anon_inode_inode pointer while other CPU
has been in anon_inode_getfile() between ihold() and d_instantiate().
Thus effectively creating dentry pointing to an inode without holding a
reference to it.

Reported-by: Sasha Levin <sasha.levin@oracle.com>
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Merge branch 'nfsd-next' of git://linux-nfs.org/~bfields/linux

Pull nfsd fix frm Bruce Fields:
"J R Okajima sent this early and I was just slow to pass it along,
apologies. Fortunately it's a simple fix"

* 'nfsd-next' of git://linux-nfs.org/~bfields/linux:
nfsd: fix lost nfserrno() call in nfsd_setattr()

Merge branch 'for-linus' of git://git./linux/kernel/git/viro/vfs

Pull vfs fixes from Al Viro:
"These four commits are obvious fixes (a couple of fdget_pos()-related
  ones from Eric Biggers, prepend_name() fix, missing checks for false
  negatives from __lookup_mnt() in fs/namei.c)"

For now I'm pulling just the four obvious fixes, there's another four
pending in Al's 'for-linus' branch wrt the mnt_hash list that were more
involved.

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
  rcuwalk: recheck mount_lock after mountpoint crossing attempts
  make prepend_name() work correctly when called with negative *buflen
  vfs: Don't let __fdget_pos() get FMODE_PATH files
  vfs: atomic f_pos access in llseek()

Revert "xen: properly account for _PAGE_NUMA during xen pte translations"

This reverts commit a9c8e4beeeb64c22b84c803747487857fe424b68.

PTEs in Xen PV guests must contain machine addresses if _PAGE_PRESENT
is set and pseudo-physical addresses is _PAGE_PRESENT is clear.

This is because during a domain save/restore (migration) the page
table entries are "canonicalised" and uncanonicalised". i.e., MFNs are
converted to PFNs during domain save so that on a restore the page
table entries may be rewritten with the new MFNs on the destination.
This canonicalisation is only done for PTEs that are present.

This change resulted in writing PTEs with MFNs if _PAGE_PROTNONE (or
_PAGE_NUMA) was set but _PAGE_PRESENT was clear. These PTEs would be
migrated as-is which would result in unexpected behaviour in the
destination domain. Either a) the MFN would be translated to the
wrong PFN/page; b) setting the _PAGE_PRESENT bit would clear the PTE
because the MFN is no longer owned by the domain; or c) the present
bit would not get set.

Symptoms include "Bad page" reports when munmapping after migrating a
domain.

Signed-off-by: David Vrabel <david.vrabel@citrix.com>
Acked-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: <stable@vger.kernel.org> [3.12+]

xen/balloon: flush persistent kmaps in correct position

Xen balloon driver will update ballooned out pages' P2M entries to point
to scratch page for PV guests. In 24f69373e2 ("xen/balloon: don't alloc
page while non-preemptible", kmap_flush_unused was moved after updating
P2M table. In that case for 32 bit PV guest we might end up with

  P2M    X -----> S  (S is mfn of balloon scratch page)
  M2P    Y -----> X  (Y is mfn in persistent kmap entry)

kmap_flush_unused() iterates through all the PTEs in the kmap address
space, using pte_to_page() to obtain the page. If the p2m and the m2p
are inconsistent the incorrect page is returned.  This will clear
page->address on the wrong page which may cause subsequent oopses if
that page is currently kmap'ed.

Move the flush back between get_page and __set_phys_to_machine to fix
this.

Signed-off-by: Wei Liu <wei.liu2@citrix.com>
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
Cc: stable@vger.kernel.org # 3.12+

Linux 3.14-rc8

Merge branch 'parisc-3.14' of git://git./linux/kernel/git/deller/parisc-linux

Pull parisc updates from Helge Deller:
- revert parts of the latest patch regarding font selection with STICON
   console
- wire up the utimes() syscall for parisc
- remove the unused parisc tmpalias code and unnecessary arch*relax
   defines

* 'parisc-3.14' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux:
  parisc: locks: remove redundant arch_*_relax operations
  parisc: wire up sys_utimes
  parisc: Remove unused CONFIG_PARISC_TMPALIAS code
  partly revert commit 8a10bc9: parisc/sti_console: prefer Linux fonts over built-in ROM fonts

Merge git://git./linux/kernel/git/davem/sparc

Pull sparc fixes from David Miller:

1) Do serial locking in a way that makes things clear that these are
    IRQ spinlocks.

2) Conversion to generic idle loop broke first generation Niagara
    machines, need to have %pil interrupts enabled during cpu yield
    hypervisor call.

3) Do not use magic constants for iterations over tsb tables, from Doug
    Wilson.

4) Fix erroneous truncation of 64-bit system call return values to
    32-bit.  From Dave Kleikamp.

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc:
  sparc64: Make sure %pil interrupts are enabled during hypervisor yield.
  sparc64:tsb.c:use array size macro rather than number
  sparc64: don't treat 64-bit syscall return codes as 32-bit
  sparc: serial: Clean up the locking for -rt

Merge git://git./linux/kernel/git/davem/net

Pull networking fixes from David Miller:

1) OpenVswitch's lookup_datapath() returns error pointers, so don't
    check against NULL.  From Jiri Pirko.

2) pfkey_compile_policy() code path tries to do a GFP_KERNEL allocation
    under RCU locks, fix by using GFP_ATOMIC when necessary.  From
    Nikolay Aleksandrov.

3) phy_suspend() indirectly passes uninitialized data into the ethtool
    get wake-on-land implementations.  Fix from Sebastian Hesselbarth.

4) CPSW driver unregisters CPTS twice, fix from Benedikt Spranger.

5) If SKB allocation of reply packet fails, vxlan's arp_reduce() defers
    a NULL pointer.  Fix from David Stevens.

6) IPV6 neigh handling in vxlan doesn't validate the destination
    address properly, and it builds a packet with the src and dst
    reversed.  Fix also from David Stevens.

7) Fix spinlock recursion during subscription failures in TIPC stack,
    from Erik Hugne.

8) Revert buggy conversion of davinci_emac to devm_request_irq, from
    Chrstian Riesch.

9) Wrong flags passed into forwarding database netlink notifications,
    from Nicolas Dichtel.

10) The netpoll neighbour soliciation handler checks wrong ethertype,
    needs to be ETH_P_IPV6 rather than ETH_P_ARP.  Fix from Li RongQing.

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (34 commits)
  tipc: fix spinlock recursion bug for failed subscriptions
  vxlan: fix nonfunctional neigh_reduce()
  net: davinci_emac: Fix rollback of emac_dev_open()
  net: davinci_emac: Replace devm_request_irq with request_irq
  netpoll: fix the skb check in pkt_is_ns
  net: micrel : ks8851-ml: add vdd-supply support
  ip6mr: fix mfc notification flags
  ipmr: fix mfc notification flags
  rtnetlink: fix fdb notification flags
  tcp: syncookies: do not use getnstimeofday()
  netlink: fix setsockopt in mmap examples in documentation
  openvswitch: Correctly report flow used times for first 5 minutes after boot.
  via-rhine: Disable device in error path
  ATHEROS-ATL1E: Convert iounmap to pci_iounmap
  vxlan: fix potential NULL dereference in arp_reduce()
  cnic: Update version to 2.5.20 and copyright year.
  cnic,bnx2i,bnx2fc: Fix inconsistent use of page size
  cnic: Use proper ulp_ops for per device operations.
  net: cdc_ncm: fix control message ordering
  ipv6: ip6_append_data_mtu do not handle the mtu of the second fragment properly
  ...

tipc: fix spinlock recursion bug for failed subscriptions

If a topology event subscription fails for any reason, such as out
of memory, max number reached or because we received an invalid
request the correct behavior is to terminate the subscribers
connection to the topology server. This is currently broken and
produces the following oops:

[27.953662] tipc: Subscription rejected, illegal request
[27.955329] BUG: spinlock recursion on CPU#1, kworker/u4:0/6
[27.957066]  lock: 0xffff88003c67f408, .magic: dead4ead, .owner: kworker/u4:0/6, .owner_cpu: 1
[27.958054] CPU: 1 PID: 6 Comm: kworker/u4:0 Not tainted 3.14.0-rc6+ #5
[27.960230] Hardware name: Bochs Bochs, BIOS Bochs 01/01/2011
[27.960874] Workqueue: tipc_rcv tipc_recv_work [tipc]
[27.961430]  ffff88003c67f408 ffff88003de27c18 ffffffff815c0207 ffff88003de1c050
[27.962292]  ffff88003de27c38 ffffffff815beec5 ffff88003c67f408 ffffffff817f0a8a
[27.963152]  ffff88003de27c58 ffffffff815beeeb ffff88003c67f408 ffffffffa0013520
[27.964023] Call Trace:
[27.964292]  [<ffffffff815c0207>] dump_stack+0x45/0x56
[27.964874]  [<ffffffff815beec5>] spin_dump+0x8c/0x91
[27.965420]  [<ffffffff815beeeb>] spin_bug+0x21/0x26
[27.965995]  [<ffffffff81083df6>] do_raw_spin_lock+0x116/0x140
[27.966631]  [<ffffffff815c6215>] _raw_spin_lock_bh+0x15/0x20
[27.967256]  [<ffffffffa0008540>] subscr_conn_shutdown_event+0x20/0xa0 [tipc]
[27.968051]  [<ffffffffa000fde4>] tipc_close_conn+0xa4/0xb0 [tipc]
[27.968722]  [<ffffffffa00101ba>] tipc_conn_terminate+0x1a/0x30 [tipc]
[27.969436]  [<ffffffffa00089a2>] subscr_conn_msg_event+0x1f2/0x2f0 [tipc]
[27.970209]  [<ffffffffa0010000>] tipc_receive_from_sock+0x90/0xf0 [tipc]
[27.970972]  [<ffffffffa000fa79>] tipc_recv_work+0x29/0x50 [tipc]
[27.971633]  [<ffffffff8105dbf5>] process_one_work+0x165/0x3e0
[27.972267]  [<ffffffff8105e869>] worker_thread+0x119/0x3a0
[27.972896]  [<ffffffff8105e750>] ? manage_workers.isra.25+0x2a0/0x2a0
[27.973622]  [<ffffffff810648af>] kthread+0xdf/0x100
[27.974168]  [<ffffffff810647d0>] ? kthread_create_on_node+0x1a0/0x1a0
[27.974893]  [<ffffffff815ce13c>] ret_from_fork+0x7c/0xb0
[27.975466]  [<ffffffff810647d0>] ? kthread_create_on_node+0x1a0/0x1a0

The recursion occurs when subscr_terminate tries to grab the
subscriber lock, which is already taken by subscr_conn_msg_event.
We fix this by checking if the request to establish a new
subscription was successful, and if not we initiate termination of
the subscriber after we have released the subscriber lock.

Signed-off-by: Erik Hugne <erik.hugne@ericsson.com>
Reviewed-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

vxlan: fix nonfunctional neigh_reduce()

The VXLAN neigh_reduce() code is completely non-functional since
check-in. Specific errors:

1) The original code drops all packets with a multicast destination address,
even though neighbor solicitations are sent to the solicited-node
address, a multicast address. The code after this check was never run.
2) The neighbor table lookup used the IPv6 header destination, which is the
solicited node address, rather than the target address from the
neighbor solicitation. So neighbor lookups would always fail if it
got this far. Also for L3MISSes.
3) The code calls ndisc_send_na(), which does a send on the tunnel device.
The context for neigh_reduce() is the transmit path, vxlan_xmit(),
where the host or a bridge-attached neighbor is trying to transmit
a neighbor solicitation. To respond to it, the tunnel endpoint needs
to do a *receive* of the appropriate neighbor advertisement. Doing a
send, would only try to send the advertisement, encapsulated, to the
remote destinations in the fdb -- hosts that definitely did not do the
corresponding solicitation.
4) The code uses the tunnel endpoint IPv6 forwarding flag to determine the
isrouter flag in the advertisement. This has nothing to do with whether
or not the target is a router, and generally won't be set since the
tunnel endpoint is bridging, not routing, traffic.

The patch below creates a proxy neighbor advertisement to respond to
neighbor solicitions as intended, providing proper IPv6 support for neighbor
reduction.

Signed-off-by: David L Stevens <dlstevens@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge branch 'davinci_emac'

Christian Riesch says:

====================
net: davinci_emac: Fix interrupt requests and error handling

since commit 6892b41d9701283085b655c6086fb57a5d63fa47 (Linux 3.11) the
davinci_emac driver is broken. After doing ifconfig down, ifconfig up,
requesting the interrupts for the driver fails. The interface remains dead
until the board is rebooted.

The first patch in this patchset reverts commit
6892b41d9701283085b655c6086fb57a5d63fa47 partially and makes the driver
useable again.

During the work on the first patch, a number of bugs in the error handling
of the driver's ndo_open code were found. The second patch fixes these bugs.

I believe the first patch meets the rules for stable kernels, I therefore added
the stable tag to this patch. The second patch is just cleanup, the code
that is fixed by this patch is only executed in case of an error.
====================

Signed-off-by: David S. Miller <davem@davemloft.net>