John Crispin [Tue, 22 Apr 2014 08:08:06 +0000 (08:08 +0000)]
Fix vr9_phy22f_a2x.bin firmware linking
vr9_phy22f_a2x.bin needs to be linked in order to get ethernet support.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
SVN-Revision: 40543
John Crispin [Tue, 22 Apr 2014 08:08:02 +0000 (08:08 +0000)]
linux/generic: add MIB counters and port status to ADM6996 switch
This patch adds port status information and MIB counters to the ADM6996
switch driver.
The driver supports also the older ADM6996L-variant, but I'm not able to
test this patch on that chip. According to the datasheet the same
registers exist there as well, so I think it should work, but any
feedback is appreciated.
Signed-off-by: Matti Laakso <malaakso at elisanet.fi>
SVN-Revision: 40542
John Crispin [Tue, 22 Apr 2014 08:07:53 +0000 (08:07 +0000)]
lantiq: fix maximum ethernet header length
The total ethernet frame length should be written to the hardware
register LTQ_ETOP_IGPLEN instead of just the value of the MTU. This
patch fixes network issues on various Danube boards, especially when
VLAN tagging is enabled.
Signed-off-by: Matti Laakso <malaakso at elisanet.fi>
SVN-Revision: 40541
Zoltan Herpai [Mon, 21 Apr 2014 18:16:03 +0000 (18:16 +0000)]
[3.14]: add missing symbols in prepping for afs patchset
Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
SVN-Revision: 40540
Zoltan Herpai [Mon, 21 Apr 2014 18:14:17 +0000 (18:14 +0000)]
[3.10]: add missing symbols in prepping for afs patchset
Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
SVN-Revision: 40539
Zoltan Herpai [Mon, 21 Apr 2014 18:13:19 +0000 (18:13 +0000)]
[3.13]: add missing symbols in prepping for afs patchset
Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
SVN-Revision: 40538
Luka Perkov [Sat, 19 Apr 2014 21:39:12 +0000 (21:39 +0000)]
[tools] scons: upgrade to 2.3.1
Signed-off-by: Luka Perkov <luka@openwrt.org>
SVN-Revision: 40535
Luka Perkov [Sat, 19 Apr 2014 21:39:11 +0000 (21:39 +0000)]
[tools] mpc: upgrade to 1.0.2
Signed-off-by: Luka Perkov <luka@openwrt.org>
SVN-Revision: 40534
Luka Perkov [Sat, 19 Apr 2014 21:39:10 +0000 (21:39 +0000)]
[tools] flex: upgrade to version 2.5.39
Signed-off-by: Luka Perkov <luka@openwrt.org>
SVN-Revision: 40533
Luka Perkov [Sat, 19 Apr 2014 21:39:09 +0000 (21:39 +0000)]
kobs-ng: Add support for overriding size
By default kobs-ng will use the size of /dev/mtd0 for the IMX bootstreams.
This patch allows overriding that size in order to reserve space at the end
of the mtd partition for u-boot.img in the case of using an SPL bootloader.
For example, to flash an SPL bootloader that loads u-boot.img from 0xe0000
(14MB) offset in a 16MB /dev/mtd0:
kobs-ng init -v -x --search_exponent=1 --chip_0_size=0xe00000 SPL
nandwrite --start=0xe00000 --pad /dev/mtd0 u-boot.img
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
SVN-Revision: 40532
Luka Perkov [Sat, 19 Apr 2014 21:39:04 +0000 (21:39 +0000)]
imx6-gateworks: enable new canbus packages
The canbus package was recently changed to a more active project. This patch
updates the default package names to include the same functionality as before.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
SVN-Revision: 40531
Felix Fietkau [Sat, 19 Apr 2014 17:26:11 +0000 (17:26 +0000)]
feeds.conf.default: the telephony feed is now on git.openwrt.org
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 40530
Felix Fietkau [Sat, 19 Apr 2014 09:58:40 +0000 (09:58 +0000)]
netifd: update to the latest version, fixes some more issues related to l3_dev handling
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 40529
Felix Fietkau [Fri, 18 Apr 2014 17:27:38 +0000 (17:27 +0000)]
base-files: remove duplicate wps button handler (#15621)
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 40528
Felix Fietkau [Fri, 18 Apr 2014 14:58:01 +0000 (14:58 +0000)]
build: reimplement package build directory override
Remove leftover pieces from package-version-override.mk support
Add a new variable USE_SOURCE_DIR to use a custom build directory.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 40527
Jo-Philipp Wich [Thu, 17 Apr 2014 17:59:47 +0000 (17:59 +0000)]
fstools: fix extroot with opkg-installed block-mount (#15550)
The /sbin/block binary now requires and additional shared library, therfore set
LD_LIBRARY_PATH accordingly when invoking it from the temporary overlay.
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>
SVN-Revision: 40526
John Crispin [Wed, 16 Apr 2014 12:11:24 +0000 (12:11 +0000)]
lantiq: remove uboot lzma patch, apparently its not needed after all
Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 40521
John Crispin [Wed, 16 Apr 2014 12:01:24 +0000 (12:01 +0000)]
uboot-lantiq: backport lzma fix
Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 40520
John Crispin [Wed, 16 Apr 2014 12:01:09 +0000 (12:01 +0000)]
lantiq: ARV7519RW22: several fixes
- Fix ethernet ports.
- Clean DTS files.
- WiFi is lantiq based (not supported yet), remove ath9k.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
SVN-Revision: 40519
Zoltan Herpai [Mon, 14 Apr 2014 21:36:39 +0000 (21:36 +0000)]
sunxi: remove mainlined patches
Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
SVN-Revision: 40512
Steven Barth [Mon, 14 Apr 2014 10:11:54 +0000 (10:11 +0000)]
ds-lite: disable NAT according to RFC 7084
Signed-off-by: Steven Barth <steven@midlink.org>
SVN-Revision: 40511
Steven Barth [Mon, 14 Apr 2014 10:11:34 +0000 (10:11 +0000)]
firewall: add support for nat-rules and netifd-proto-originating rules
Signed-off-by: Steven Barth <steven@midlink.org>
SVN-Revision: 40510
Gabor Juhos [Sun, 13 Apr 2014 20:41:52 +0000 (20:41 +0000)]
ar71xx: rb91x: fix ethernet packet loss issues
The RB91x boards are suffering from ethernet packet loss after a cold
boot. The cause of the problem is that the AR8035 PHYs requires special
register settings to work reliably on these boards.
Enable the RGMII TX, RX delays and disable SmartEE functionality of
the AR8035 PHYs. Also enable the RXD delay in the ETH_CFG register
to fix the issue.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 40509
Gabor Juhos [Sun, 13 Apr 2014 20:41:51 +0000 (20:41 +0000)]
ar71xx/mikrotik: enable the AT803x PHY driver
It will be used on the RB91x boards.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 40508
Gabor Juhos [Sun, 13 Apr 2014 20:41:50 +0000 (20:41 +0000)]
ar71xx: allow to configure AR803x PHYs via platform data
Add a patch for the at803x phy driver, in order to be able
to configure some register settings via platform data.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 40507
Gabor Juhos [Sun, 13 Apr 2014 20:41:48 +0000 (20:41 +0000)]
ar71xx: add phy_mmd_{read,write} helpers
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 40506
Gabor Juhos [Sun, 13 Apr 2014 20:41:42 +0000 (20:41 +0000)]
ar71xx: enable console on the RB91x boards
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 40505
John Crispin [Sun, 13 Apr 2014 18:01:08 +0000 (18:01 +0000)]
ralink: add port_init for rt2880
Forgotten patch to fix ethernet for rt2880.
Based on previously submitted patch from Claudio.
Signed-off-by: Roman Yeryomin <roman@advem.lv>
SVN-Revision: 40504
Felix Fietkau [Sun, 13 Apr 2014 09:53:51 +0000 (09:53 +0000)]
iw: sync nl80211.h (fixes settting antenna_gain)
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 40503
Gabor Juhos [Sun, 13 Apr 2014 08:29:09 +0000 (08:29 +0000)]
ar71xx: add profile and build image for the ZyXEL NBG6716 board
Signed-off-by: André Valentin <avalentin@marcant.net>
Patchwork: http://patchwork.openwrt.org/patch/5101/
[juhosg: remove the non-existing zyxelnand subtarget specific stuff]
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 40502
Gabor Juhos [Sun, 13 Apr 2014 08:29:08 +0000 (08:29 +0000)]
uboot-envtools: add support for the ZyXEL NBG6716 board
Signed-off-by: André Valentin <avalentin@marcant.net>
Patchwork: http://patchwork.openwrt.org/patch/5101/
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 40501
Gabor Juhos [Sun, 13 Apr 2014 08:29:07 +0000 (08:29 +0000)]
ar71xx: add user-space support for the ZyXEL NBG6716 board
Signed-off-by: André Valentin <avalentin@marcant.net>
Patchwork: http://patchwork.openwrt.org/patch/5101/
[juhosg: use zyxel prefix in LED names]
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 40500
Gabor Juhos [Sun, 13 Apr 2014 08:29:05 +0000 (08:29 +0000)]
ar71xx: add kernel support for ZyXEL NBG 6716
With this patch OpenWRT supports the following on the ZyXEL NBG 6716:
-WiFi 2G (ath9k)
-WiFi 5G (ath10k)
-NAND flash
-2 Ethernet interfaces
-USB 2.0
-LEDs including switch
-reasonale defaults at first boot
Signed-off-by: André Valentin <avalentin@marcant.net>
Patchwork: http://patchwork.openwrt.org/patch/5101/
[juhosg:
- rename and refresh kernel patch,
- fix a few typos,
- change button key codes,
- use zyxel prefix in LED names]
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 40499
John Crispin [Sat, 12 Apr 2014 21:22:21 +0000 (21:22 +0000)]
lantiq: enable switch on td8970
Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 40498
John Crispin [Sat, 12 Apr 2014 21:22:17 +0000 (21:22 +0000)]
802.11s: fix authsae support in netifd
This patch implements support for 802.11s protected mesh wireless networks (using authsae) in the netifd framework.
Until meshd-nl80211 implements a proper -P option for the PID file, this uses shell backgrounding in order to be able to get the PID for the process.
Signed-off-by: Vittorio Gambaletta <openwrt@vittgam.net>
SVN-Revision: 40497
John Crispin [Sat, 12 Apr 2014 21:22:12 +0000 (21:22 +0000)]
rpcd: update to the latest version
This is required to make object "session" procedure "access" dump ACLs
when no "object" or no "function" parameters are passed.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 40496
John Crispin [Sat, 12 Apr 2014 21:22:08 +0000 (21:22 +0000)]
Fix ARV7519RW images
This patch moves ARV7519RW definitions to VR9 section from the AR9 section and removes a whitespace that breaks jffs2 image generation.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
SVN-Revision: 40495
John Crispin [Sat, 12 Apr 2014 21:22:04 +0000 (21:22 +0000)]
Fix Asus rt-n15 board support
* gpio leds and buttons
* ethernet
Signed-off-by: Roman Yeryomin <roman@advem.lv>
SVN-Revision: 40494
John Crispin [Sat, 12 Apr 2014 21:22:00 +0000 (21:22 +0000)]
rt2880 DT fixes
* add pinctrl
* fix ethernet port
* make wifi available by default
Signed-off-by: Roman Yeryomin <roman@advem.lv>
SVN-Revision: 40493
John Crispin [Sat, 12 Apr 2014 21:21:56 +0000 (21:21 +0000)]
Fix pinmux-rt2880
The last arg to FUNC() is count, not last pin.
Signed-off-by: Roman Yeryomin <roman@advem.lv>
SVN-Revision: 40492
John Crispin [Sat, 12 Apr 2014 21:21:53 +0000 (21:21 +0000)]
Add wmac clock for rt2880
Signed-off-by: Roman Yeryomin <roman@advem.lv>
SVN-Revision: 40491
John Crispin [Sat, 12 Apr 2014 21:21:49 +0000 (21:21 +0000)]
sparse: add as a new package selectable from the config
This change does multiple things, all related to enable sparse usage as
a static analysis tool selectable from the OpenWrt configuration:
*add a KERNEL_SPARSE option in the config to add sparse to the kernel
build (through the C=1 option usage)
*add sparse as a new host tools. It will get selected automatically when
the above option will be enabled
Signed-off-by: Mathieu Olivari <mathieu@qca.qualcomm.com>
SVN-Revision: 40490
John Crispin [Sat, 12 Apr 2014 21:21:44 +0000 (21:21 +0000)]
Don't try to generate whr-g300n image if it's going to be more than 4M
Signed-off-by: Roman Yeryomin <roman@advem.lv>
SVN-Revision: 40489
John Crispin [Sat, 12 Apr 2014 21:21:40 +0000 (21:21 +0000)]
uboot-lantiq: enable parallel building
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
SVN-Revision: 40488
John Crispin [Sat, 12 Apr 2014 21:21:35 +0000 (21:21 +0000)]
uboot-lantiq: reuse/copy VR9 GPHY firmware blobs from target/linux/lantiq
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
SVN-Revision: 40487
John Crispin [Sat, 12 Apr 2014 21:21:31 +0000 (21:21 +0000)]
uboot-lantiq: add packages for AudioCodes MP-252
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
SVN-Revision: 40486
John Crispin [Sat, 12 Apr 2014 21:21:26 +0000 (21:21 +0000)]
uboot-lantiq: add packages for various Arcadyan boards
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
SVN-Revision: 40485
John Crispin [Sat, 12 Apr 2014 21:21:23 +0000 (21:21 +0000)]
uboot-lantiq: add packages for Lantiq EASY80920
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
SVN-Revision: 40484
John Crispin [Sat, 12 Apr 2014 21:21:18 +0000 (21:21 +0000)]
uboot-lantiq: add packages for Lantiq EASY50712
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
SVN-Revision: 40483
John Crispin [Sat, 12 Apr 2014 21:21:14 +0000 (21:21 +0000)]
uboot-lantiq: update to v2013.10
Patches created from tree:
git@github.com:danielschwierzeck/u-boot-lantiq.git
v2013.10..u-boot-lantiq-v2013.10-openwrt4
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
SVN-Revision: 40482
Gabor Juhos [Sat, 12 Apr 2014 20:22:41 +0000 (20:22 +0000)]
ar71xx: build firmware image for the WNDR3700 v4 board
Based on the the WNDR3700v4 support patch from Ralph Perlich:
http://patchwork.openwrt.org/patch/4763/
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 40481
Gabor Juhos [Sat, 12 Apr 2014 20:00:37 +0000 (20:00 +0000)]
ar71xx/image: allow to use more arguments for some macros
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 40480
Gabor Juhos [Sat, 12 Apr 2014 19:58:23 +0000 (19:58 +0000)]
ar71xx: wndr4300: indicate WNDR3700v4 in the kernel support files
Apart from the wireless chip, the WNDR3700 v4 and the WNDR4300
is the same device. Indicate this in the kernel files.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 40479
Gabor Juhos [Sat, 12 Apr 2014 19:58:20 +0000 (19:58 +0000)]
ar71xx: wndr4300: enable 5V power for the USB port
The 5V power of the USB is controlled by a GPIO pin of
the external WiFi chip. Setup the GPIO bitmasks in the
platform data of the WiFi chip to ensure that the 5V
power gets enabled by the ath9k driver.
Based on the the WNDR3700v4 support patch from Ralph Perlich:
http://patchwork.openwrt.org/patch/4763/
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 40478
Gabor Juhos [Sat, 12 Apr 2014 17:53:34 +0000 (17:53 +0000)]
ar71xx: wndr4300: use KEY_RFKILL code for the Wireless button
Based on the the WNDR3700v4 support patch from Ralph Perlich:
http://patchwork.openwrt.org/patch/4763/
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 40477
Gabor Juhos [Sat, 12 Apr 2014 17:42:36 +0000 (17:42 +0000)]
ar71xx: add default LED config for WiFi LEDs on the WNDR4300
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 40476
Gabor Juhos [Sat, 12 Apr 2014 17:42:35 +0000 (17:42 +0000)]
ar71xx: wndr4300: add LED for 2.4Ghz wifi interface
Based on the the WNDR3700v4 support patch from Ralph Perlich:
http://patchwork.openwrt.org/patch/4763/
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 40475
Gabor Juhos [Sat, 12 Apr 2014 17:42:34 +0000 (17:42 +0000)]
ar71xx: wndr4300: select GPIO_OUT functionality for LED GPIOs
The bootloader does not initializes the output function
correctly for all LEDs. DO that from the board setup code.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 40474
Gabor Juhos [Sat, 12 Apr 2014 17:42:33 +0000 (17:42 +0000)]
ar71xx: wndr4300: change 'orange' to 'amber' in LED color names
The hardware manual says amber so change the color part of
the LED names to reflect that. Also update the constant names.
Based on the the WNDR3700v4 support patch from Ralph Perlich:
http://patchwork.openwrt.org/patch/4763/
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 40473
Gabor Juhos [Sat, 12 Apr 2014 16:01:45 +0000 (16:01 +0000)]
ar71xx: fix typos in TP-Link rssileds definition
Signed-off-by: Felix Kaechele <heffer@fedoraproject.org>
Patchwork: http://patchwork.openwrt.org/patch/5109/
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 40472
Gabor Juhos [Sat, 12 Apr 2014 16:01:43 +0000 (16:01 +0000)]
ar71xx: add rssileds for Ubiquiti XM boards
Adds support for the received signal strength indicator LEDs of the
Bullet M, Nanostation M and Rocket M devices.
Signed-off-by: Felix Kaechele <heffer@fedoraproject.org>
Patchwork: http://patchwork.openwrt.org/patch/5108/
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 40471
Felix Fietkau [Sat, 12 Apr 2014 15:43:17 +0000 (15:43 +0000)]
kernel: mark kmod-usb-phy-nop as hidden to avoid building it where it is not needed
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 40470
Felix Fietkau [Sat, 12 Apr 2014 14:28:34 +0000 (14:28 +0000)]
hostapd: fix "bad number" error due to missing wps_pbc_in_m1 option (since r39995)
r39995 introduced a new parameter wps_pbc_in_m1 to wifi wps config, but
apparently did not provide a default value 0.
When that option's non-existing value is later evaluated in
/lib/netifd/hostapd.sh, it causes the "bad number" error to be logged in
syslog if user has not set the wps_pbc_in_m1 option. The error materialises
only if user has enabled wps.
Sat Apr 12 13:25:01 2014 daemon.notice netifd: radio1 (1254): sh: bad number
Sat Apr 12 13:25:01 2014 daemon.notice netifd: radio0 (1253): sh: bad number
Discussion in bug 15508: https://dev.openwrt.org/ticket/15508#comment:3
Error is caused by line 282:
https://dev.openwrt.org/browser/trunk/package/network/services/hostapd/files/netifd.sh#L282
My patch sets the parameter's default value to 0, which does nothing. The
default might also be set a bit later in the function, but this felt like the
most clear place to do that.
Signed-off-by hnyman <hannu.nyman@iki.fi>
SVN-Revision: 40469
Gabor Juhos [Sat, 12 Apr 2014 12:05:18 +0000 (12:05 +0000)]
x86/net5501: remove broken flag
According to Christophe, the kernel boots on the Soekris net5501
board.
Reported-by: Christophe Prevotaux <cprevotaux@nltinc.com>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 40468
Gabor Juhos [Sat, 12 Apr 2014 11:59:07 +0000 (11:59 +0000)]
kernel: update 3.10 to 3.10.36
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 40467
Gabor Juhos [Sat, 12 Apr 2014 11:59:05 +0000 (11:59 +0000)]
ar71xx: fix image generation
Move the comments out from the shell script to fix build
breakage introduced in r40464.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 40466
Gabor Juhos [Sat, 12 Apr 2014 10:21:04 +0000 (10:21 +0000)]
ar71xx: avoid spurious restarts caused by the watchdog on AR934x
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 40465
Gabor Juhos [Sat, 12 Apr 2014 09:52:58 +0000 (09:52 +0000)]
ar71xx: add comments for image Makefile.
Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
Patchwork: http://patchwork.openwrt.org/patch/5075/
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 40464
Gabor Juhos [Sat, 12 Apr 2014 09:52:54 +0000 (09:52 +0000)]
ar71xx: initial support for TP-Link Archer C7v2
The C7v2 has 16 MB flash and QCA9880-BR4A rev 2 supported by ath10k driver.
The C7v1 had 8 MB flash and the unsupported QCA9880-AR1A rev 1.
Signed-off-by: Adam Serbinski <adam@serbinski.com>
Patchwork: http://patchwork.openwrt.org/patch/5071/
[juhosg:
- remove the v2 specific profile add the ath10k driver to the existing
Archer C7 profile instead. Although on v1 devices it does not change
the non-working behaviour, but the ath10k driver is useful for users
whom have replaced the wifi card with a supported one in their units.
- update image/Makefile to build firmware image for both boards if the
Archer C7 profile is selected]
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 40463
Florian Fainelli [Fri, 11 Apr 2014 22:38:54 +0000 (22:38 +0000)]
brcm2708: add missing configuration symbols
Spotted by buildbot and while doing a CONFIG_ALL=y build.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
SVN-Revision: 40462
John Crispin [Fri, 11 Apr 2014 20:40:34 +0000 (20:40 +0000)]
lantiq: add an extra partition to the TDW8970 flash that can be used to store the vdsl firmware
Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 40461
John Crispin [Fri, 11 Apr 2014 20:40:24 +0000 (20:40 +0000)]
lantiq: more vdsl related cleanups
* atm module needs to be loaded before linux-atm
* use absolute firmware paths
* extended validation
* add a script for mounting an optional firmware partition
Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 40460
Felix Fietkau [Fri, 11 Apr 2014 20:28:55 +0000 (20:28 +0000)]
netifd: switch to using git.openwrt.org
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 40459
Jo-Philipp Wich [Fri, 11 Apr 2014 16:14:09 +0000 (16:14 +0000)]
uci: fix import with not yet existing packages, preserve config permissions on commit, fix Lua detection in cmake
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>
SVN-Revision: 40458
Jo-Philipp Wich [Fri, 11 Apr 2014 16:13:27 +0000 (16:13 +0000)]
uhttpd: do not attempt to configure Lua handler if referenced file does not exist
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>
SVN-Revision: 40457
Felix Fietkau [Fri, 11 Apr 2014 13:48:41 +0000 (13:48 +0000)]
netifd: update to latest version, adds a force_link parameter to bring up an interface without active device carrier
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 40456
Felix Fietkau [Fri, 11 Apr 2014 13:22:28 +0000 (13:22 +0000)]
x86_64: add usb support (including storage) to the kernel config
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 40455
Felix Fietkau [Fri, 11 Apr 2014 13:22:24 +0000 (13:22 +0000)]
x86: set default kernel version to 3.10
Place the previous selection (3.3.8) into the only subtarget that did
not override it to 3.10
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 40454
Felix Fietkau [Fri, 11 Apr 2014 13:22:19 +0000 (13:22 +0000)]
x86: remove linux 3.8 support
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 40453
Imre Kaloz [Fri, 11 Apr 2014 10:19:26 +0000 (10:19 +0000)]
[x86_64]: generate esxi compatible vmdks, too
Signed-off-by: Imre Kaloz <kaloz@openwrt.org>
SVN-Revision: 40452
Imre Kaloz [Fri, 11 Apr 2014 10:14:57 +0000 (10:14 +0000)]
[x86_64]: reuqire qemu-img to be installed (the one we have in tools is too old)
Signed-off-by: Imre Kaloz <kaloz@openwrt.org>
SVN-Revision: 40451
Felix Fietkau [Thu, 10 Apr 2014 15:21:13 +0000 (15:21 +0000)]
netifd: update to the latest version, fixes some reload issues with proto=static
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 40449
Felix Fietkau [Thu, 10 Apr 2014 14:43:33 +0000 (14:43 +0000)]
kernel: add a dependency of kmod-r8169 on r8169-firmware
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 40448
Felix Fietkau [Thu, 10 Apr 2014 14:43:30 +0000 (14:43 +0000)]
linux-firmware: add a new package for firmware (currently only builds r8169 firmware)
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 40447
Felix Fietkau [Thu, 10 Apr 2014 14:43:26 +0000 (14:43 +0000)]
build: add support for packing version control downloads with xz
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 40446
Felix Fietkau [Thu, 10 Apr 2014 14:43:22 +0000 (14:43 +0000)]
generic: remove obsolete symbol export from block2mtd init patch
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 40445
Felix Fietkau [Thu, 10 Apr 2014 14:43:17 +0000 (14:43 +0000)]
x86: try harder to attach block2mtd to fix boot issues on devices with longer delays
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 40444
Felix Fietkau [Thu, 10 Apr 2014 11:31:21 +0000 (11:31 +0000)]
netifd: fix a regression related to ppp + multiple updates (ipv4 + ipv6)
Fixes #15504
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 40443
Imre Kaloz [Thu, 10 Apr 2014 11:09:27 +0000 (11:09 +0000)]
[x86_64]: specify the adapter type for the vmdk conversion
Signed-off-by: Imre Kaloz <kaloz@openwrt.org>
SVN-Revision: 40442
Felix Fietkau [Thu, 10 Apr 2014 08:52:33 +0000 (08:52 +0000)]
mac80211: add back missing tx power handling fix (#12750)
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 40440
John Crispin [Thu, 10 Apr 2014 08:14:33 +0000 (08:14 +0000)]
lantiq: move the dsl-modem config to network.@dsl-modem[-1]
make sure uci_defaults generates a proper uci config for the v/adsl modem
Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 40439
John Crispin [Wed, 9 Apr 2014 16:36:28 +0000 (16:36 +0000)]
lantiq: vdsl init.d script should auto start
Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 40438
John Crispin [Wed, 9 Apr 2014 16:31:24 +0000 (16:31 +0000)]
lantiq: cleanup vdsl driver bringup
config interface 'wan'
# a, b, j
option annex b
# a, b, av, bv
option tone b
# vdsl.bin
option firmware
# atm, ptm
option xfer_mode atm
Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 40437
John Crispin [Wed, 9 Apr 2014 16:31:14 +0000 (16:31 +0000)]
lantiq: make dsl_notify.sh executable
Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 40436
Steven Barth [Wed, 9 Apr 2014 12:29:43 +0000 (12:29 +0000)]
odhcpd: use correct defaults for interfaces not in UCI
SVN-Revision: 40435
Imre Kaloz [Wed, 9 Apr 2014 11:54:44 +0000 (11:54 +0000)]
[x86_64]: enable native KVM and VMware drivers
Signed-off-by: Imre Kaloz <kaloz@openwrt.org>
SVN-Revision: 40434
Imre Kaloz [Wed, 9 Apr 2014 11:46:18 +0000 (11:46 +0000)]
[x86_64]: upgrade to 3.14
Signed-off-by: Imre Kaloz <kaloz@openwrt.org>
SVN-Revision: 40433
Steven Barth [Wed, 9 Apr 2014 06:57:04 +0000 (06:57 +0000)]
odhcp6c: fix recovering from status where all addresses have been lost
SVN-Revision: 40432
Felix Fietkau [Tue, 8 Apr 2014 22:11:27 +0000 (22:11 +0000)]
mac80211: fix warnings triggered by tx power changes when using WDS AP (#15491)
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 40430
Felix Fietkau [Tue, 8 Apr 2014 22:11:23 +0000 (22:11 +0000)]
mac80211: fix user antenna gain calculation
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 40429
projects / openwrt / svn-archive / archive.git / log