Robert Marko [Fri, 11 Apr 2025 22:32:23 +0000 (00:32 +0200)]
bcm63xx-cfe: install into image staging dir
Currently, bcm63xx-cfe is being installed into kernel build dir, however
that does not work for Image Builder as only certain artifacts from kernel
build dir are included in Image Builder.
So, simply install bcm63xx-cfe into image staging dir so its artifacts can
be used in Image Builder as well.
Fixes: #18408
Fixes: #18409
Link: https://github.com/openwrt/openwrt/pull/18463
Signed-off-by: Robert Marko <robimarko@gmail.com>
FUKAUMI Naoki [Wed, 29 Jan 2025 07:35:43 +0000 (07:35 +0000)]
rockchip: Add support for Radxa ROCK 4SE
The Radxa ROCK 4SE[1] is a single board computer using the Rockchip
RK3399-T.
Hardware
--------
- Dual-core Cortex-A72 and quad-core Cortex-A53 CPU
- Mali-T860MP4 GPU
- LPDDR4 4GB RAM
- M.2 M Key slot (PCIe 2.1 x4)
- eMMC connector
- microSD card slot
- Wi-Fi 5 (not supported)
- Gigabit Ethernet with PoE support (additional PoE HAT required)
- USB 3.0 Type-A OTG port
- USB 3.0 Type-A HOST port
- 2x USB 2.0 Type-A HOST ports
- USB Type-C power port (5V only)
- 40 Pin GPIO header
[1] https://radxa.com/products/rock4/4se
Installation
------------
Uncompress the OpenWrt sysupgrade and write it to the micro SD card or
internal eMMC using dd.
Signed-off-by: FUKAUMI Naoki <naoki@radxa.com>
Link: https://github.com/openwrt/openwrt/pull/17554
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
FUKAUMI Naoki [Wed, 29 Jan 2025 07:33:59 +0000 (07:33 +0000)]
rockchip: Add support for Radxa ROCK 4C+
The Radxa ROCK 4C+[1] is a single board computer with dual HDMI using
the Rockchip RK3399-T.
Hardware
--------
- Dual-core Cortex-A72 and quad-core Cortex-A53 CPU
- Mali-T860MP4 GPU
- LPDDR4 4GB RAM
- eMMC connector
- microSD card slot
- Wi-Fi 5 (not supported)
- Gigabit Ethernet with PoE support (additional PoE HAT required)
- USB 3.0 Type-A OTG port
- USB 3.0 Type-A HOST port
- 2x USB 2.0 Type-A HOST ports
- USB Type-C power port (5V only)
- 40 Pin GPIO header
[1] https://radxa.com/products/rock4/4cp
Installation
------------
Uncompress the OpenWrt sysupgrade and write it to the micro SD card or
internal eMMC using dd.
Signed-off-by: FUKAUMI Naoki <naoki@radxa.com>
Link: https://github.com/openwrt/openwrt/pull/17554
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Schneider Azima [Mon, 10 Mar 2025 01:42:51 +0000 (18:42 -0700)]
mediatek: add support for Mercusys MR80X v3
This commit adds support for Mercusys MR80X(EU) v3 router.
Device specification:
- SoC: Mediatek MT7981b, Cortex-A53, 64-bit
- RAM: 512MB
- Flash: SPI NAND GigaDevice GD5F1GQ5UEYIGY (128 MB)
- Ethernet: 4x 100/1000 Mbps LAN1,LAN2,LAN3 & WAN
- Wireless: 2.4GHz (802.11 b/g/n/ax)
- Wireless: 5GHz (802.11 a/n/ac/ax)
- LEDs: 1 orange and 1 green status LEDs, 4 green gpio-controlled LEDs
on ethernet ports
- Buttons: 1 (Reset)
- Bootloader: Main U-Boot - U-Boot 2022.01-rc4. Additionally, both UBI
slots contain "seconduboot" (also U-Boot 2022.01-rc4)
Installation (UART):
- Place OpenWrt initramfs-kernel image on tftp server with IP 192.168.1.2
- Attach UART, switch on the router and interrupt the boot process by
pressing 'Ctrl-C'.
- Set the uboot environment for startup.
setenv tp_boot_idx 0; setenv bootcmd bootm 0x46000000; saveenv
If the bootarg is set to boot from ubi1, also change it to ubi0.
- Load and run OpenWrt initramfs image.
setenv serverip 192.168.1.2; setenv ipaddr 192.168.1.1; tftpboot initramfs-kernel.bin; bootm
- Browse IP 192.168.1.1, upload the 'sysupgrade' image and do upgrade.
Recovery:
- Press Reset button and power on the router.
- Navigate to U-Boot recovery web server (http://192.168.1.1/) and
upload the OEM firmware.
Stock layout:
0x000000000000-0x000000200000 : "boot"
0x000000200000-0x000000300000 : "u-boot-env"
0x000000300000-0x000003500000 : "ubi0"
0x000003500000-0x000006700000 : "ubi1"
0x000006700000-0x000006f00000 : "userconfig"
0x000006f00000-0x000007300000 : "tp_data"
ubi0/ubi1 format:
U-Boot at boot checks that all volumes are in place:
+-------------------------------+
| Volume Name: uboot Vol ID: 0|
| Volume Name: kernel Vol ID: 1|
| Volume Name: rootfs Vol ID: 2|
+-------------------------------+
MAC addresses:
+---------+-------------------+-----------+
| | MAC | Algorithm |
+---------+-------------------+-----------+
| label | 94:0C:xx:xx:xx:12 | label |
| WAN | 94:0C:xx:xx:xx:13 | label+1 |
| LAN | 94:0C:xx:xx:xx:12 | label |
| WLAN 2g | 94:0C:xx:xx:xx:11 | label-1 |
| WLAN 5g | 94:0C:xx:xx:xx:10 | label-2 |
+---------+-------------------+-----------+
label MAC address was found in UBI partition "tp_data", file
"default-mac".
Signed-off-by: Schneider Azima <Schneider-Azima12@protonmail.com>
Link: https://github.com/openwrt/openwrt/pull/18181
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
John Audia [Fri, 11 Apr 2025 13:52:08 +0000 (09:52 -0400)]
kernel: bump 6.6 to 6.6.87
Changelog: https://cdn.kernel.org/pub/linux/kernel/v6.x/ChangeLog-6.6.87
Manually rebased:
generic-hack/781-usb-net-rndis-support-asr.patch
All other patches automatically rebased.
Build system: x86/64
Build-tested: flogic/xiaomi_redmi-router-ax6000-ubootmod, ramips/tplink_archer-a6-v3, x86/64
Run-tested: flogic/xiaomi_redmi-router-ax6000-ubootmod, ramips/tplink_archer-a6-v3, x86/64
Signed-off-by: John Audia <therealgraysky@proton.me>
Link: https://github.com/openwrt/openwrt/pull/18457
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Mantas Pucka [Fri, 4 Apr 2025 09:46:58 +0000 (12:46 +0300)]
wifi-scripts: add hotplug handler for slow-to-initialize ath12k radios
Some ath12k radios can take long time to initialize and register a
phy. This can cause netifd to fail to detect them during initial scan.
To address this issue, a hotplug script has been added to retry
configuration once they have registered their phy.
Signed-off-by: Mantas Pucka <mantas@8devices.com>
Link: https://github.com/openwrt/openwrt/pull/18459
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Mantas Pucka [Thu, 27 Mar 2025 15:20:07 +0000 (17:20 +0200)]
linux-firmware: ath12k: package firmware for QCN9274
Package wireless firmware for Qualcomm QCN9274.
Signed-off-by: Mantas Pucka <mantas@8devices.com>
Link: https://github.com/openwrt/openwrt/pull/18459
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Mantas Pucka [Fri, 4 Apr 2025 12:02:17 +0000 (15:02 +0300)]
mac80211: ath12k: add patches for 160MHz support
Add series enabling 160MHz channels on ath12k
Signed-off-by: Mantas Pucka <mantas@8devices.com>
Link: https://github.com/openwrt/openwrt/pull/18459
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Mantas Pucka [Tue, 1 Apr 2025 12:04:35 +0000 (15:04 +0300)]
mac80211: ath12k: fix wideband operation on QCN9274
Add patches to enable QCN9274 radios that support both 5GHz and 6GHz
bands.
Signed-off-by: Mantas Pucka <mantas@8devices.com>
Link: https://github.com/openwrt/openwrt/pull/18459
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Mantas Pucka [Thu, 27 Mar 2025 15:28:46 +0000 (17:28 +0200)]
mac80211: ath12k: support fetching regdb from board-2.bin
In board-2.bin available at linux-firmare regdb is stored with
board-id=255. This change is needed to properly use it.
Signed-off-by: Mantas Pucka <mantas@8devices.com>
Link: https://github.com/openwrt/openwrt/pull/18459
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Mantas Pucka [Wed, 9 Apr 2025 08:24:23 +0000 (11:24 +0300)]
qualcommbe: ipq95xx: pcs: fix USXGMII link-up failure
USXGMII link-up may fail due to too short delay after PLL reset.
Increase the delay to fix this.
Signed-off-by: Mantas Pucka <mantas@8devices.com>
Link: https://github.com/openwrt/openwrt/pull/18459
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Mantas Pucka [Fri, 28 Mar 2025 08:42:00 +0000 (10:42 +0200)]
qualcommbe: ipq95xx: pcs: support 2.5G PHY
Fixes to PCS driver to support 2.5G PHY
Signed-off-by: Mantas Pucka <mantas@8devices.com>
Link: https://github.com/openwrt/openwrt/pull/18459
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Mantas Pucka [Fri, 28 Mar 2025 08:40:44 +0000 (10:40 +0200)]
qualcommbe: ipq95xx: nsscc: fix port5 clock parent
Fix incorrect port5 clock management
Signed-off-by: Mantas Pucka <mantas@8devices.com>
Link: https://github.com/openwrt/openwrt/pull/18459
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Mantas Pucka [Fri, 11 Apr 2025 14:38:28 +0000 (17:38 +0300)]
qualcommbe: ipq95xx: add bus clock for NSSCC
Missing bus clock prevent access to NSSCC registers and thus it is
impossible change clock configuration, when ethernet connection speed
changes.
Signed-off-by: Mantas Pucka <mantas@8devices.com>
Link: https://github.com/openwrt/openwrt/pull/18459
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Mantas Pucka [Thu, 27 Mar 2025 10:02:51 +0000 (12:02 +0200)]
qualcommbe: ipq95xx: fix PCIe operation
Add patches that fix:
* Wrong MSI interrups for PCIe3
* Hang during reboot due to stopped clocks
Signed-off-by: Mantas Pucka <mantas@8devices.com>
Link: https://github.com/openwrt/openwrt/pull/18459
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Paul Donald [Wed, 26 Mar 2025 17:43:45 +0000 (18:43 +0100)]
lldpd: enable hardware inventory information (TLV) management
lldpd can send several hardware inventory TLV fields. Extend the init
script to provide these when the existing flag 'lldpmed_no_inventory' is
disabled. Five new methods provide default values for some of them,
taken from /etc/os-release and /etc/board.json.
There is no homogeneous method to determine the hardware serial number,
so it can be provided manually, as can asset ID.
Note: properties >= 32 characters are truncated at send time (by lldpd),
and some (Cisco) equipment displays junk after strings >= 32 characters.
So truncate to 31.
Tested on: 24.10.0 (known compatible with 22 and 23 also)
===
Example
===
The following lldpd config lines:
configure inventory hardware-revision "v0"
configure inventory software-revision "r28427-
6df0e3d02a"
configure inventory firmware-revision "OpenWrt 24.10.0"
configure inventory serial-number "ABCDEF-123456"
configure inventory manufacturer "glinet"
configure inventory model "GL.iNet GL-MT6000"
# 32 characters:
configure inventory asset "abcdefghijklmnopqrstuvwxyz 12345"
Produce the following TLV (decoded by Wireshark):
Telecommunications Industry Association TR-41 Committee - Inventory - Hardware Revision
1111 111. .... .... = TLV Type: Organization Specific (127)
.... ...0 0000 0110 = TLV Length: 6
Organization Unique Code: 00:12:bb (Telecommunications Industry Association TR-41 Committee)
Media Subtype: Inventory - Hardware Revision (0x05)
Hardware Revision: v0
Telecommunications Industry Association TR-41 Committee - Inventory - Firmware Revision
1111 111. .... .... = TLV Type: Organization Specific (127)
.... ...0 0001 0011 = TLV Length: 19
Organization Unique Code: 00:12:bb (Telecommunications Industry Association TR-41 Committee)
Media Subtype: Inventory - Firmware Revision (0x06)
Firmware Revision: OpenWrt 24.10.0
Telecommunications Industry Association TR-41 Committee - Inventory - Software Revision
1111 111. .... .... = TLV Type: Organization Specific (127)
.... ...0 0001 0101 = TLV Length: 21
Organization Unique Code: 00:12:bb (Telecommunications Industry Association TR-41 Committee)
Media Subtype: Inventory - Software Revision (0x07)
Software Revision: r28427-
6df0e3d02a
Telecommunications Industry Association TR-41 Committee - Inventory - Serial Number
1111 111. .... .... = TLV Type: Organization Specific (127)
.... ...0 0001 0100 = TLV Length: 20
Organization Unique Code: 00:12:bb (Telecommunications Industry Association TR-41 Committee)
Media Subtype: Inventory - Serial Number (0x08)
Serial Number: ABCDEF-123456
Telecommunications Industry Association TR-41 Committee - Inventory - Manufacturer Name
1111 111. .... .... = TLV Type: Organization Specific (127)
.... ...0 0000 1010 = TLV Length: 10
Organization Unique Code: 00:12:bb (Telecommunications Industry Association TR-41 Committee)
Media Subtype: Inventory - Manufacturer Name (0x09)
Manufacturer Name: glinet
Telecommunications Industry Association TR-41 Committee - Inventory - Model Name
1111 111. .... .... = TLV Type: Organization Specific (127)
.... ...0 0001 0101 = TLV Length: 21
Organization Unique Code: 00:12:bb (Telecommunications Industry Association TR-41 Committee)
Media Subtype: Inventory - Model Name (0x0a)
Model Name: GL.iNet GL-MT6000
Telecommunications Industry Association TR-41 Committee - Inventory - Asset ID
1111 111. .... .... = TLV Type: Organization Specific (127)
.... ...0 0010 0011 = TLV Length: 35
Organization Unique Code: 00:12:bb (Telecommunications Industry Association TR-41 Committee)
Media Subtype: Inventory - Asset ID (0x0b)
Asset ID: abcdefghijklmnopqrstuvwxyz 1234
The Cisco DUT displays:
Hardware Revision: v0
Firmware Revision: OpenWrt 24.10.0
Software Revision: r28427-
6df0e3d02a
Serial Number: ABCDEF-123456
Manufacturer Name: glinet
Model Name: GL.iNet GL-MT6000
Asset ID: abcdefghijklmnopqrstuvwxyz 1234
Signed-off-by: Paul Donald <newtwen+github@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/18354
Signed-off-by: Robert Marko <robimarko@gmail.com>
Christian Marangi [Fri, 11 Apr 2025 19:40:31 +0000 (21:40 +0200)]
ath10k-ct: partially revert removal of 003 patch
Partially revert removal of 003 patch to fix compilation error with
kernel 6.6.
In 6.6 .remove still require int and .remove_new needs to be used.
Fixes: bfb106e8ae73 ("mac80211: backport API change for sta rate control update")
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Christian Marangi [Fri, 11 Apr 2025 09:45:13 +0000 (11:45 +0200)]
generic: fix kernel warning no previous prototype for ...
It seems new kernel version introduced -Wmissing-prototypes. This new
warning reported drivers that define non static function that are used
statically in the driver.
Fix this by declaring making those function actually static if not
defined in any header and not used outside of the single driver.
Co-authored-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Link: https://github.com/openwrt/openwrt/pull/18455
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Christian Marangi [Fri, 11 Apr 2025 09:38:55 +0000 (11:38 +0200)]
generic: add missing of.h header to ar8327
It seems new kernel linux version reorganized the header include and now
of.h needs to be explicitly included. This should have been done from
when the driver was introduced.
Add the missing of.h header to fix compilation error in later kernel
version.
Co-authored-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Link: https://github.com/openwrt/openwrt/pull/18455
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Felix Fietkau [Fri, 11 Apr 2025 11:02:19 +0000 (13:02 +0200)]
unetmsg: allow communication between hosts if no service is defined
Simplifies unet setup
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Christian Marangi [Thu, 10 Apr 2025 19:35:25 +0000 (21:35 +0200)]
ubootenv-nvram: convert driver to .remove_new
Convert driver to .remove_new in preparation for kernel 6.12 support.
Link: https://github.com/openwrt/openwrt/pull/18454
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Christian Marangi [Thu, 10 Apr 2025 19:34:41 +0000 (21:34 +0200)]
ltq-ptm: convert driver to .remove_new
Convert driver to .remove_new in preparation for kernel 6.12 support.
Link: https://github.com/openwrt/openwrt/pull/18454
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Christian Marangi [Thu, 10 Apr 2025 19:33:53 +0000 (21:33 +0200)]
ltq-deu: convert driver to .remove_new
Convert driver to .remove_new in preparation for kernel 6.12 support.
Link: https://github.com/openwrt/openwrt/pull/18454
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Christian Marangi [Thu, 10 Apr 2025 19:33:05 +0000 (21:33 +0200)]
ltq-atm: convert driver to .remove_new
Convert driver to .remove_new in preparation for kernel 6.12 support.
Link: https://github.com/openwrt/openwrt/pull/18454
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Christian Marangi [Thu, 10 Apr 2025 19:32:19 +0000 (21:32 +0200)]
ltq-adsl-mei: convert driver to .remove_new
Convert driver to .remove_new in preparation for kernel 6.12 support.
Link: https://github.com/openwrt/openwrt/pull/18454
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Christian Marangi [Thu, 10 Apr 2025 19:31:02 +0000 (21:31 +0200)]
gpio-button-hotplug: convert to .remove_new
Convert package to .remove_new in preparation for kernel 6.12 support.
Link: https://github.com/openwrt/openwrt/pull/18454
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Christian Marangi [Thu, 10 Apr 2025 19:29:11 +0000 (21:29 +0200)]
generic: convert driver to .remove_new
Convert driver to .remove_new in preparation for kernel 6.12 support.
Link: https://github.com/openwrt/openwrt/pull/18454
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Felix Fietkau [Fri, 11 Apr 2025 09:09:33 +0000 (11:09 +0200)]
mt76: update to Git HEAD (2025-04-11)
3e25f2bc33af wifi: mt76: mt7925: introduce MLO capability control
ce3622257026 wifi: mt76: mt7925: fix fails to enter low power mode in suspend state
dfdb8e975718 wifi: mt76: mt7915: fix possible integer overflows in mt7915_muru_stats_show()
29f0ad5a439a wifi: mt76: mt7925: ensure wow pattern command align fw format
5eab65bb5473 wifi: mt76: mt7925: fix country count limitation for CLC
d6a197dbc9a2 wifi: mt76: Add check for devm_kstrdup()
901492c4621a wifi: mt76: mt7925: Remove unnecessary if-check
24062ce4fa0f wifi: mt76: mt7925: Simplify HIF suspend handling to avoid suspend fail
56c0beddbed8 wifi: mt76: mt7921: fix kernel panic due to null pointer dereference
11bacfcce3b9 Revert "wifi: mt76: mt7925: Update mt7925_mcu_uni_[tx,rx]_ba for MLO"
2823c50b1c15 wifi: mt76: mt7925: fix the wrong link_idx when has p2p_device
f54ff3cabab6 wifi: mt76: mt7925: fix the wrong simultaneous cap for MLO
aa7d366ccf40 wifi: mt76: mt7925: adjust rm BSS flow to prevent next connection failure
d25359e8bb83 wifi: mt76: mt7925: integrate *mlo_sta_cmd and *sta_cmd
25a0285d8ee3 wifi: mt76: mt7925: update the power-saving flow
5910f0806c05 wifi: mt76: mt7925: load the appropriate CLC data based on hardware type
454a69cbb718 wifi: mt76: mt7925: add EHT control support based on the CLC data
bdc09b8f2321 wifi: mt76: mt7925: update the channel usage when the regd domain changed
772dcb4b4e61 wifi: mt76: mt7925: remove unused acpi function for clc
b94b025490ef wifi: mt76: mt792x: extend MTCL of APCI to version3 for EHT control
9ff2afce5fef wifi: mt76: mt7925: add MTCL support to enhance the regulatory compliance
f11807364258 wifi: mt76: add mt76_get_power_bound helper function
ffd1cbfc485e wifi: mt76: mt7921: fix returned txpower
687e2fdfbf40 wifi: mt76: mt7925: fix returned txpower
43aaa62fbc55 wifi: mt76: mt7915: cleanup mt7915_get_power_bound
a4be3fc9ed4b wifi: mt76: mt7996: cleanup mt7996_get_power_bound
0ba7a69f8927 wifi: mt76: move napi_enable() from under BH
1b370c689a2f wifi: mt76: mt7921: avoid undesired changes of the preset regulatory domain
e931cecc45de mt76: mt792x: fix unused variable warning
539e7e711a15 Revert "wifi: mt76: mt7925: fix returned txpower"
67c724cc60b1 Revert "wifi: mt76: mt7921: fix returned txpower"
52f51a398e7e wifi: mt76: mt7996: Add change_vif_links stub
b3b61abd733f wifi: mt76: mt7996: Introduce mt7996_sta_link container
915938e83c35 wifi: mt76: mt7996: Add mt7996_sta_link struct in mt7996_vif_link
3e06380a43a4 wifi: mt76: mt7996: Add vif_cfg_changed callback
f419c62e9198 wifi: mt76: mt7996: Add link_info_changed callback
3082c9edbe35 wifi: mt76: mt7996: Add mt7996_sta_state routine
46e20e5d7455 wifi: mt76: mt7996: Rely on mt7996_sta_link in sta_add/sta_remove callbacks
1de180821525 wifi: mt76: mt7996: Add mt7996_mac_sta_change_links callback
2efb26f1fc10 wifi: mt76: mt7996: Support MLO in mt7996_mac_sta_event()
2e249744bc12 wifi: mt76: Check link_conf pointer in mt76_connac_mcu_sta_basic_tlv()
0eee20d3e388 wifi: mt76: mt7996: Update mt7996_mcu_add_sta to MLO support
200ce414fe61 wifi: mt76: mt7996: Rely on mt7996_vif_link in mt7996_mcu_twt_agrt_update signature
d195324131ba wifi: mt76: mt7996: Rely on mt7996_vif/sta_link in twt teardown
7757e7c140f7 wifi: mac80211: call rate_control_rate_update() for link STA
a3b651aeb551 wifi: mt76: mt7996: Update mt7996_mcu_add_rate_ctrl to MLO
2a005953dc49 wifi: mt76: mt7996: Add mt7996_mcu_sta_mld_setup_tlv() and mt7996_mcu_sta_eht_mld_tlv()
58e8b71782fc wifi: mt76: mt7996: Add mt7996_mcu_teardown_mld_sta rouine
e0b422f2acaf wifi: mt76: mt7996: rework mt7996_mac_write_txwi() for MLO support
21aa0c288470 wifi: mt76: mt7996: Rely on wcid_to_sta in mt7996_mac_add_txs_skb()
87c437fa8b43 wifi: mt76: mt7996: rework mt7996_rx_get_wcid to support MLO
9b4de3ce7fc7 wifi: mt76: mt7996: rework mt7996_sta_set_4addr and mt7996_sta_set_decap_offload to support MLO
a369b0c14d25 wifi: mt76: mt7996: Add mt7996_sta_link to mt7996_mcu_add_bss_info signature
9c6ec015afbb wifi: mt76: mt7996: rework mt7996_set_hw_key to support MLO
60967d28a5e0 wifi: mt76: mt7996: rework mt7996_sta_hw_queue_read to support MLO
3668d57795e3 wifi: mt76: mt7996: remove mt7996_mac_enable_rtscts()
275e6a681bac wifi: mt76: mt7996: rework mt7996_mac_sta_rc_work to support MLO
057822770ca5 wifi: mt76: mt7996: rework mt7996_mac_sta_poll to support MLO
b9682a51c109 wifi: mt76: mt7996: rework mt7996_update_mu_group to support MLO
d1a5a0afa6d6 wifi: mt76: mt7996: rework mt7996_net_fill_forward_path to support MLO
56529041b364 wifi: mt76: mt7996: rework mt7996_mcu_add_obss_spr to support MLO
c788d5748dc8 wifi: mt76: mt7996: rework mt7996_mcu_beacon_inband_discov to support MLO
974e6c2df98b wifi: mt76: mt7996: set vif default link_id adding/removing vif links
70717b761af2 wifi: mt76: mt7996: rework set/get_tsf callabcks to support MLO
d01b9d300eaa wifi: mt76: mt7996: rework mt7996_ampdu_action to support MLO
d5cddf65f7a7 wifi: mt76: mt7996: Update mt7996_tx to MLO support
a1ed21a66913 wifi: mt76: mt792x: re-register CHANCTX_STA_CSA only for the mt7921 series
a826fc287483 wifi: mt76: mt7925: update MLO cleanup flow during disconnection
0994f0af632e wifi: mt76: mt7925: fix the incomplete revert of [tx,rx]_ba for MLO
5169d4e8669b wifi: mt76: mt76x2u: add TP-Link TL-WDN6200 ID to device table
46f3a10a9f0f mt76: mt7925: sync with upstream cleanups
de635e1e3adc wifi: mt76: mt7996: fix locking in mt7996_mac_sta_rc_work()
63a4edf1cb74 wifi: mt76: mt7996: add macros for pci decive id
a2dd2f7896f7 wifi: mt76: connac: add support to load firmware for mt7990
3908cf04aa39 wifi: mt76: mt7996: rework WA mcu command for mt7990
6243414a4e80 wifi: mt76: mt7996: rework DMA configuration for mt7990
a8def214d736 wifi: mt76: mt7996: rework register mapping for mt7990
51db7a2d57f6 wifi: mt76: mt7996: add eeprom support for mt7990
d0799f3303e9 wifi: mt76: mt7996: adjust HW capabilities for mt7990
10c3ea97a86d wifi: mt76: connac: rework TX descriptor and TX free for mt7990
bc588ac3d104 wifi: mt76: mt7996: rework background radar check for mt7990
f8c3dd3677dd wifi: mt76: mt7996: add PCI device id for mt7990
3cec186474c4 wifi: mt76: mt7915: set correct background radar capability
9bacdb2bf2c3 wifi: mt76: mt7915: rework radar HWRDD idx
a19543c7e05e wifi: mt76: mt7996: rework radar HWRDD idx
b0cf33e76a3a wifi: mt76: mt7925: Fix logical vs bitwise typo
0433adc883c9 wifi: mt76: mt7925: add EHT preamble puncturing
be28ef77e330 wifi: mt76: mt7996: Add NULL check in mt7996_thermal_init
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Felix Fietkau [Wed, 19 Mar 2025 11:40:50 +0000 (12:40 +0100)]
mac80211: backport API change for sta rate control update
Helps stay in sync with mt76 upstream development
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Felix Fietkau [Thu, 3 Apr 2025 09:51:41 +0000 (11:51 +0200)]
cli: extend remove call to allow passing values directly
This simplifies script or API usage of this command to remove values directly
without having to calculate the index
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Yang Xiwen [Thu, 10 Apr 2025 11:09:42 +0000 (19:09 +0800)]
qualcommax: eap623od-hd-v1: fix phy node and LED config
The reason phy fails to probe without explicitly overrided phy id is
that the reset timing fails to match. Fix it with proper `reset-delay-us` and
`reset-post-delay-us`.
While at it, change LED settings to match EAP610-Outdoor.
Signed-off-by: Yang Xiwen <forbidden405@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/18450
Signed-off-by: Robert Marko <robimarko@gmail.com>
Sergii Shcherbakov [Sat, 1 Feb 2025 01:24:28 +0000 (02:24 +0100)]
ramips: mt76x8: add support for MERCUSYS MB130-4G v1
Specification:
SoC: MediaTek MT7628AN
RAM: 128 MB, Zentel A3R1GE40JBF-8E
Flash: 16MB, Winbond W25Q128JV
Switch: rt3050-esw, 2 ports 100 Mbps
WiFi: MediaTek mt7628-wmac 2.4GHz 802.11n and MediaTek MT7663 5GHz
802.11ac (PCIe)
WWAN: Quectel EC200A-EL 4G modem (USB)
GPIO:
* 1 button (Reset/WPS)
* 6 LEDs (Power+WPS, LAN, 3xSignal)
* USB port power controls
* Modem reset
* Modem programming switch
* Internal/external antenna switch for 4G
Serial Interface:
TP10 - 3.3V can be used for level shifter, if needed
TP9 - TX
TP8 - RX
TP11 - GND
Interface properties: 115200, 8N1
Access to console using serial port for OEM firmware:
Username: admin
Password: 1234
Flashing via TFTP (no disassembling or soldering required):
1. Connect your PC and router to port LAN
2. Configure PC interface using static IP 192.168.1.225, mask
255.255.255.0
3. Place OpenWRT firmware image (*-squashfs-tftp-recovery.bin) to TFTP
root folder and renamed it to tp_recovery.bin
4. Unplug power from router
5. Press and hold Reset/WPS button
6. Power up the router
7. Wait until TFTP started uploading image (~10 seconds after power up)
and release Reset/WPS button
8. Wait until image uploaded, i.e. until LAN LED start lighting
9. Enable DHCP address on PC interface and wait for assigning address
10. Use ssh (root@192.168.1.1) to configure router properties
Depends on patch for firmware-utils package:
https://github.com/openwrt/firmware-utils/commit/
2051fe5b
Signed-off-by: Sergii Shcherbakov <shchers@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17819
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Álvaro Fernández Rojas [Thu, 10 Apr 2025 12:01:33 +0000 (14:01 +0200)]
package: add kmod-r8127 ethernet driver
r8127 is an out of tree driver provided by Realtek for RTL8127 devices.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Yujie Zhu [Tue, 8 Apr 2025 14:51:55 +0000 (22:51 +0800)]
mediatek: filogic: add Netcore N60 Pro support
Hardware specification:
SoC: MediaTek MT7986A 4x A53
Flash: ESMT F50L1G41LB 128MB
RAM: M16U4G16256A DDR4 512MB
Ethernet: 2x 2.5G + 3x 1G
USB: 1x USB 3.0
WiFi1: MT7975N 2.4GHz 4T4R
WiFi2: MT7975PN 5GHz 4T4R
Button: Reset, WPS
Power: DC 12V 2A
Flash instructions:
Connect to the router using ssh or telnet,
username: useradmin, password is the web
login password of the router.
Use scp to upload bl31-uboot.fip and flash:
"mtd write xxx-bl31-uboot.fip FIP"
"mtd erase ubi"
Connect to the router via the Lan port,
set a static ip of your PC.
(ip 192.168.1.254, gateway 192.168.1.1)
Download initramfs image, reboot router,
waiting for tftp recovery to complete.
After openwrt boots up, perform sysupgrade.
Note:
Back up all mtd partitions before flashing.
Signed-off-by: Yujie Zhu <libriunc@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/18138
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Christian Marangi [Thu, 10 Apr 2025 10:23:34 +0000 (12:23 +0200)]
qualcommbe: disable CONFIG_QCOM_IPA kernel config
CONFIG_QCOM_IPA kernel cofig was enabled by mistake and conflicts with
mac80211 as it indirectly selects QMI HELPERS. Backports project provid
his own version of QMI HELPERS hence it should not be built-in.
Link: https://github.com/openwrt/openwrt/pull/17788
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Christian Marangi [Thu, 30 Jan 2025 15:55:57 +0000 (16:55 +0100)]
qualcommbe: ipq95xx: Make RPM partition read-only
Make the RPM partition read-only. This was a mistake and a leftover from
staging branch but I can take this mistake as an excuse to document the
current problem with RPM.
It might happen that a board ship with a broken RPM .mbn, broken not in
the sense that the board doesn't boot or it's a brick but broken in the
sense that it's outdaed and suffer from a bug fixed in new version.
This bug consist in a problem with the regulators between USB and NSS.
The old RPM mess with the NSS regulator (l2) and change the voltage for
it while configuring the USB regulator (l5).
This cause the ethernet subsystem to malfunction with the port not
working.
To workaround this, it's needed to disable RPM handling and CPUFreq.
With these 2 disabled, the old RPM doesn't touch regulators and Ethernet
works correctly.
New RPM correctly handle regulators for USB (l5) and doesn't suffer from
this problem. A solution for this is getting discussed with QCOM hoping
to get some good feedback for it.
Link: https://github.com/openwrt/openwrt/pull/17788
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Christian Marangi [Thu, 30 Jan 2025 15:54:02 +0000 (16:54 +0100)]
qualcommbe: ipq95xx: Add pending patch fixing NSSCC boot stall
Add pending patch fixing NSSCC boot stall. These patch are needed to
prevent the ICC to disable critical clock for NSSCC NOC.
Without these the system will stall and reboot with watchdog.
While at it also remove an extra clock from DTSI as it currently have no
use. Original patch is not modified to keep consistency with series
proposed upstream.
Link: https://github.com/openwrt/openwrt/pull/17788
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Christian Marangi [Thu, 30 Jan 2025 15:47:04 +0000 (16:47 +0100)]
qualcommbe: ipq95xx: Drop redundant comment in NSSCC clock patch
Drop redundant comment in NSSCC clock patch. The problem has been
identified hence the comment doesn't apply anymore.
Link: https://github.com/openwrt/openwrt/pull/17788
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Christian Marangi [Thu, 30 Jan 2025 15:45:16 +0000 (16:45 +0100)]
qualcommbe: ipq95xx: Define default partition table for RFB SPI-NAND
Define default partition table for SPI-NAND mounted on reference board.
This is where is normally placed the rootfs UBI.
Link: https://github.com/openwrt/openwrt/pull/17788
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Christian Marangi [Thu, 30 Jan 2025 15:41:51 +0000 (16:41 +0100)]
qualcommbe: ipq95xx: Refresh dts SPI-NAND patch to v14
Refresh dts SPI-NAND patch to to v14. This is to keep stuff synced with
current pending patch revision and make it easier to replace patch
later (and discover something broke in the meantime)
Link: https://github.com/openwrt/openwrt/pull/17788
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Christian Marangi [Thu, 30 Jan 2025 15:49:03 +0000 (16:49 +0100)]
qualcommbe: ipq95xx: Refresh the NSSCC and PORT patch for new PCIe patches
Refresh the NSSCC patch for new PCIe patches. To keep track of fuzz
changes for the IPQ95xx patches, patch are not refreshed currently.
For the specific case of NSSCC patch, quilt gets confused and apply the
patch in the wrong node, putting it in the RPM node (causing all kind of
funny errors at runtime)
Correctly fix the patch to put the node right after the PCIe nodes.
Also the PORT patch need to be refreshed as the gpio header is added by
the PCIe patch.
Link: https://github.com/openwrt/openwrt/pull/17788
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Christian Marangi [Thu, 30 Jan 2025 15:39:12 +0000 (16:39 +0100)]
qualcommbe: ipq95xx: Add PCIe upstream patch and related nodes
Add PCIe upstream patch and related nodes to enable PCIe on IPQ95xx.
Minimal change were required to backport the patch and apply on current
kernel. Refresh all affected patch.
Link: https://github.com/openwrt/openwrt/pull/17788
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Christian Marangi [Wed, 29 Jan 2025 20:34:41 +0000 (21:34 +0100)]
qualcommbe: ipq95xx: Add USB3 kmods and drop NSS-DP unneeded package
Add USB3 kmods to the default package list, USB3 correctly works on
IPQ95xx hence it can be enabled.
While at it drop the NSS-DP as it was added by mistake as the ethrnet
platform is handled differently on this SoC with pending upstream
drivers.
Link: https://github.com/openwrt/openwrt/pull/17788
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Christian Marangi [Wed, 29 Jan 2025 20:33:07 +0000 (21:33 +0100)]
kernel: usb: add qualcommbe to the supported target of dwc3-qcom
Add qualcommbe to the supported target of dwc3-qcom kernel module. USB3
is correctly supported on IPQ95xx and can be enabled.
Link: https://github.com/openwrt/openwrt/pull/17788
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Christian Marangi [Wed, 9 Apr 2025 17:41:37 +0000 (19:41 +0200)]
generic: move QCOM SPI NAND driver to generic backports
QCOM SPI NAND driver got merged upstream hence we can drop the special
patch from qualcommax and qualcommbe target and move them to the generic
backports directory to reduce patch maintenance.
While at it refresh any affected patch and target and also backport other
minor fixup for the SPI NAND driver merged upstream later.
Link: https://github.com/openwrt/openwrt/pull/17788
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Mieczyslaw Nalewaj [Tue, 8 Apr 2025 15:37:59 +0000 (17:37 +0200)]
kernel: bump 6.6 to 6.6.86
Changelog: https://cdn.kernel.org/pub/linux/kernel/v6.x/ChangeLog-6.6.86
Removed upstreamed:
generic/pending-6.6/155-usbnet-restore-usb%d-name-exception-for-local-mac-addresses.patch[1]
1. https://web.git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v6.6.86&id=
2beb999f73b48f3cb04d7cb9c4b5400d59f80f89
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Link: https://github.com/openwrt/openwrt/pull/18443
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Álvaro Fernández Rojas [Thu, 10 Apr 2025 08:32:56 +0000 (10:32 +0200)]
bcm27xx: pull 6.6 patches from RPi repo
Adds latest 6.6 patches from the Raspberry Pi repository.
These patches were generated from:
https://github.com/raspberrypi/linux/commits/rpi-6.6.y/
With the following command:
git format-patch -N v6.6.85..HEAD
(HEAD ->
bba53a117a4a5c29da892962332ff1605990e17a)
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Linus Walleij [Sun, 11 Jun 2023 22:15:18 +0000 (00:15 +0200)]
gemini: Activate serial USB console on the DNS-313
This brings up a serial console on the USB device port of
the DNS-313 by:
- Activating the usbgadget feature
- Selecting the usbgadget-acm package
- Adding an inittab that opens a console at ttyGS0 which is
the device side of ttyACMn of a connected host
Link: http://patchwork.ozlabs.org/project/openwrt/patch/20250403-dns313-usb-serial-v2-4-d84de8e86931@linaro.org/
Cc: Chuanhong Guo <gch981213@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Linus Walleij [Thu, 3 Apr 2025 06:30:29 +0000 (08:30 +0200)]
package: usbgadget: Fix subpackage dependencies
Currently if a target wants to use acm or ncm gadget config,
they need to select both usbgadget and the config package
such as usbgadget-acm.
It's better if the target just select usbgadget-acm and get
all dependencies satisfied.
Adding a dependency using +usbgadget fixes this.
Link: http://patchwork.ozlabs.org/project/openwrt/patch/20250403-dns313-usb-serial-v2-3-d84de8e86931@linaro.org/
Reviewed-by: Chuanhong Guo <gch981213@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Linus Walleij [Tue, 1 Apr 2025 08:53:12 +0000 (10:53 +0200)]
package: usbgadget: Define conffile
The /etc/config/usbgadget file is a conffile, so specify
it as such.
Link: http://patchwork.ozlabs.org/project/openwrt/patch/20250403-dns313-usb-serial-v2-2-d84de8e86931@linaro.org/
Reviewed-by: Chuanhong Guo <gch981213@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Linus Walleij [Tue, 1 Apr 2025 07:52:19 +0000 (09:52 +0200)]
package: usbgadget: Require kmod-fs-configfs
The usbgadget package tries to mount and use configfs so it
needs to require the kernel module instead of implying it.
There should be a newline at the end of the file as well.
Link: http://patchwork.ozlabs.org/project/openwrt/patch/20250403-dns313-usb-serial-v2-1-d84de8e86931@linaro.org/
Reviewed-by: Chuanhong Guo <gch981213@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Linus Walleij [Wed, 2 Apr 2025 21:10:39 +0000 (23:10 +0200)]
kernel: modules: Fix RTL8366RB title
The title of the RTL8366RB was wrong, probably a pure
copy/paste bug by me.
Link: http://patchwork.ozlabs.org/project/openwrt/patch/20250402-fix-rtl8366rb-title-v1-1-d3ced57a0e9c@linaro.org/
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Shiji Yang [Wed, 2 Apr 2025 15:36:28 +0000 (23:36 +0800)]
generic: crypto: fix jitterentropy initialization failed issue
Sync jitterentropy source code with linux-6.12 to solve the
issue of jitterentropy initialization failed:
[ 9.523489] jitterentropy: Initialization failed with host not compliant with requirements: 9
[ 9.661916] kmodloader: 1 module could not be probed
[ 9.662377] kmodloader: - jitterentropy_rng - 0
In linux upstream commit
cf27d9475f37 ("crypto: jitter - use
permanent health test storage"), when FIPS crypto is disabled,
the health test results are always explicitly skipped. That means
it will never return error code 9 (health test failed) again.
Fixes: https://github.com/openwrt/openwrt/issues/16684
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/18399
Signed-off-by: Robert Marko <robimarko@gmail.com>
Rosen Penev [Sat, 4 Jan 2025 22:31:07 +0000 (14:31 -0800)]
mac80211: ath9k: simplify probe with devm
Upstream backport.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17445
Signed-off-by: Robert Marko <robimarko@gmail.com>
Rosen Penev [Wed, 1 Jan 2025 19:26:16 +0000 (11:26 -0800)]
mac80211: fix led-pin usage
ath9k uses a deprecated GPIO API that assumes a starting base of 0. This
is no longer the case and so must be fixed.
Upstream pending patch.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17445
Signed-off-by: Robert Marko <robimarko@gmail.com>
Rosen Penev [Wed, 1 Jan 2025 19:21:49 +0000 (11:21 -0800)]
ath79: fix GPIO numbering with ath9k
ath9k base starts at 512. This is a problem as it uses gpio_request_one
to request the GPIO, which is legacy API.
This upstream pending patch needs to also be ported to mac80211.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17445
Signed-off-by: Robert Marko <robimarko@gmail.com>
Rosen Penev [Tue, 31 Dec 2024 22:37:45 +0000 (14:37 -0800)]
mac80211: ath9k: remove gpio buttons support
This is only used by mach files, which are no longer used in OpenWrt.
Allows removing a custon ath9k_platform.h file.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17445
Signed-off-by: Robert Marko <robimarko@gmail.com>
Rosen Penev [Tue, 31 Dec 2024 22:09:44 +0000 (14:09 -0800)]
mac80211: ath9k: remove platform leds
These only work with and are useful with mach files. Now that those are
gone, this can go too.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17445
Signed-off-by: Robert Marko <robimarko@gmail.com>
Rosen Penev [Tue, 31 Dec 2024 21:20:06 +0000 (13:20 -0800)]
mac80211: ath9k: clean up gpiochip
Simplify patch with gpiochip_add_data, struct reduction, new GPIO API,
and header cleanup.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17445
Signed-off-by: Robert Marko <robimarko@gmail.com>
Matthias Schiffer [Sat, 5 Apr 2025 10:23:44 +0000 (12:23 +0200)]
build: bpf: fix LLVM tool paths with host toolchain
Do not assume that the various tools like llc can be found under the
same path as clang; instead, look them up through BPF_PATH (while still
preferring ones found next to clang).
This fixes build in common setups with ccache, where clang resolves to a
path like /usr/lib/ccache/bin/clang, but no other tools can be found at
that location.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
Link: https://github.com/openwrt/openwrt/pull/18422
Signed-off-by: Robert Marko <robimarko@gmail.com>
Matthias Schiffer [Sat, 5 Apr 2025 11:30:12 +0000 (13:30 +0200)]
build: bpf: drop clang-11 lookup
CLANG_MIN_VER is 12, so there is no point in looking for clang-11.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
Link: https://github.com/openwrt/openwrt/pull/18422
Signed-off-by: Robert Marko <robimarko@gmail.com>
Yang Xiwen [Mon, 31 Mar 2025 00:48:23 +0000 (08:48 +0800)]
ipq60xx: add support for TP-Link EAP623-Outdoor HD v1
Specifications:
* SoC: Qualcomm IPQ6018 (64-bit Quad-core Arm Cortex-A53 @ 1800MHz)
* Memory: 1 GiB
* Serial Port: 3v3 TTL 115200n8
* Wi-Fi: QCN9074 (4x4 5 GHz 802.11ax)
* Wi-Fi: IPQ6018 (4x4 2.4 GHz 802.11b/g/n/ax)
* Ethernet: RTL8211F (10/100/1GBASE-T)
* Flash: ESMT F59D1G81MB (128 MiB)
* LEDs: 1x Green Status (GPIO 37 Active High), 1x Yellow Status (GPIO 32
Active High) and an LED global control GPIO (GPIO 36 Active High, set
up by U-Boot)
* Buttons: 1x Reset (GPIO 9 Active Low)
Installation Instructions (Serial+TFTP):
1. Solder 4 pin header to the pads near T32 and T31.
2. Connect 3V3 TTL port to TX, RX, and GND, which are pad T31, T32 and
the pad near T31 respectively. Be sure not to connect VCC and
crossover TX and RX.
3. Copy RAM firmware image
openwrt-qualcommax-ipq60xx-tplink_eap623od-hd-v1-initramfs-uImage.itb
to TFTP server root, available at 192.168.0.1.
4. Connect PoE ethernet cable to the RJ45 port and hold Ctrl+B in the
serial console (115200 baud) until autoboot is halted.
5. Run the following commands in the U-boot prompt:
# setenv serverip 192.168.0.1
# setenv ipaddr 192.168.0.99
# tftpboot 0x44000000 openwrt-qualcommax-ipq60xx-tplink_eap623od-hd-v1-initramfs-uImage.itb
# bootm
You may need to type Ctrl+C and Enter before running these commands
to clear invisible characters from the buffer.
6. Run the following command in a terminal to copy the sysupgrade image
to be installed (check IP address):
$ scp openwrt-qualcommax-ipq60xx-tplink_eap623od-hd-v1-squashfs-sysupgrade.bin root@192.168.1.1:/tmp/
7. Activate the OpenWrt serial console and run the following commands:
# cd /tmp
# sysupgrade -n openwrt-qualcommax-ipq60xx-tplink_eap623od-hd-v1-squashfs-sysupgrade.bin
8. The AP will reboot and OpenWrt will be successfully installed.
Signed-off-by: Yang Xiwen <forbidden405@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/18389
Signed-off-by: Robert Marko <robimarko@gmail.com>
Robert Marko [Tue, 8 Apr 2025 15:39:47 +0000 (17:39 +0200)]
ipq-wifi: update to Git HEAD (2025-04-08)
5aa50e188feb ipq40xx: add BDF for Alibaba AP4220
7d2a86c01a52 ipq6018: add TP-Link EAP623-Outdoor HD v1 BDF
9591c9b7578a Remove executable permissions
Signed-off-by: Robert Marko <robimarko@gmail.com>
Andrew LaMarche [Fri, 28 Mar 2025 01:06:03 +0000 (01:06 +0000)]
an7581: fix phy2 led1 function
PHY2 led1 is configured to control PHY1's LED. Change it to PHY2.
Signed-off-by: Andrew LaMarche <andrewjlamarche@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/18361
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Matthias Schiffer [Sat, 29 Mar 2025 20:32:08 +0000 (21:32 +0100)]
ipq40xx: qca8k: hook up IPQ4019 bridge flag offloading
Adds support for setting bridge port learning and isolation flags on
ipq40xx.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
Link: https://github.com/openwrt/openwrt/pull/18375
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Matthias Schiffer [Sat, 29 Mar 2025 20:31:49 +0000 (21:31 +0100)]
generic: qca8k: backport bridge port isolation support
Bridge port isolation offload support has been added to the bridge core
and many DSA drivers. mt7530 support was backported in OpenWrt commit
c4e6a147a6c0 ("generic: 6.6: mt7530: add support for bridge port
isolation").
Backport qca8k support as well.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
Link: https://github.com/openwrt/openwrt/pull/18375
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Christian Steiner [Sun, 30 Mar 2025 11:19:04 +0000 (13:19 +0200)]
realtek: add support for D-Link DGS-1210-26
This patch adds support for D-Link DGS-1210-26 rev. F1
Hardware specification
----------------------
* RTL8382M SoC, 1 MIPS 4KEc core @ 500MHz
* 128MB DRAM
* 32MB NOR Flash (MX25L25635E)
* 24 x 10/100/1000BASE-T ports
* 2 x SFP ports
* Power LED
* Reset button on front panel
Installation using OEM webinterface
-----------------------------------
1. Make sure you are running OEM firmware from secondary slot. If not, switch to image2 using the menus
System > Firmware Information > Boot from image2
Tools > reboot
2. Upload image squashfs-factory_image1.bin via Tools > Backup / Upgrade Firmware > image1
3. Toggle startup image via System > Firmware Information > Boot from image1
4. Tools > reboot
Known working firmware version for this procedure: 6.20.007
Installation using TFTP and serial console
------------------------------------------
1. Prepare a TFTP server with the OpenWrt *initramfs-kernel.bin and assign it an IP from 10.90.90.0/24 (except 10.90.90.90)
2. Connect the TFTP server to one of switch's ports
3. Connect to the serial console (115200 baud) and power on the switch
4. Press the ESC key once you see "Hit Esc key to stop autoboot" in the console output
5. Press CTRL+C keys to get into the real U-Boot prompt
6. Init the network with the command "rtk network on"
7. Load the OpenWrt image with the command "tftpboot 0x8f000000 <TFTP_SERVER_IP>:<IMAGE_FILE>"
(<TFTP_SERVER_IP> is the TFTP server's IP, e.g. 10.90.90.100; <IMAGE_FILE> is the name of the image provided by the TFTP server)
8. Boot the OpenWrt image with the command "bootm"
9. Browse to https://192.168.1.1/cgi-bin/luci/admin/system/flash
10. Upload the the OpenWrt *squashfs-sysupgrade.bin to the switch
11. Wait for it to reboot
Signed-off-by: Christian Steiner <christian.steiner@outlook.de>
Link: https://github.com/openwrt/openwrt/pull/18378
Signed-off-by: Sander Vanheule <sander@svanheule.net>
Matthias Franck [Fri, 31 Jan 2025 09:00:46 +0000 (10:00 +0100)]
busybox: use external libtirpc when using glibc
In recent glibc versions rpc functionality has been moved to a separate
library instead of glibc itself.
Depend on this library when rpc functionality is needed and glibc is
used.
Signed-off-by: Matthias Franck <matthias.franck@softathome.com>
Link: https://github.com/openwrt/openwrt/pull/17796
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Ming Kuang [Fri, 21 Mar 2025 15:21:05 +0000 (23:21 +0800)]
wifi-scripts: mac80211.sh: add EHT and HE160 support to iw_htmode
For WIFI7 devices (such as mt7925e), the dev width is currently
always "20 MHz (no HT)" in monitor mode.
Add EHT and HE160 support to iw_htmode to fix this issue.
Additionally, the following changes are made:
1. Set iw_htmode to 160MHz for VHT160. The reason for the current
VHT160 setting is unclear and seems to have been in place for
over a decade (ibss_htmode [1]). If anyone knows its impact,
please inform me so I can restore it.
2. Modify MHZ to MHz. The original matching table in the current
iw tool uses MHz. Although the match is case-insensitive,
correcting this won't hurt.
[1]: https://github.com/openwrt/openwrt/commit/
768d09be8781228d3553142c0f1e1231c6aacc7c
Signed-off-by: Ming Kuang <ming@imkuang.com>
Link: https://github.com/openwrt/openwrt/pull/18319
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
INAGAKI Hiroshi [Fri, 3 Jan 2025 08:41:46 +0000 (17:41 +0900)]
ath79: add support for NEC Aterm WG2200HP
NEC Aterm WG2200HP is a 2.4/5 GHz band 11ac (Wi-Fi 5) router, based on
QCA9558.
Specification:
- SoC : Qualcomm Atheros QCA9558
- RAM : DDR2 128 MiB (2x ESMT M14D5121632A)
- Flash : SPI-NOR 16 MiB (Macronix MX25L12835FM2I-10G)
- WLAN : 2.4/5 GHz
- 2.4 GHz : 3T3R (Qualcomm Atheros QCA9558 (SoC))
- 5 GHz : 4T4R (Qualcomm Atheros QCA9984)
- Ethernet : 5x 10/100/1000 Mbps
- switch : Qualcomm Atheros QCA8337
- LEDs/Keys (GPIO) : 12x/4x
- UART : through-hole on PCB
- assignment : 3.3V, GND, NC, TX, RX from tri-angle marking
- settings : 9600n8
- USB : 1x USB 2.0 Type-A
- Power : 12 VDC, 1.5 A (Max: 20 W)
- Stock OS : NetBSD based
Flash instruction using initramfs-factory.bin image:
1. Connect and open serial console
2. Power on WG2200HP and interrupt bootloader by ESC key
3. Login to the bootloader CLI with a password "chiron"
4. Start TFTP server by "tftpd" command
5. Upload initramfs-factory.bin via tftp from your computer
example (Windows): tftp -i 192.168.0.1 PUT initramfs-factory.bin
6. Boot initramfs image by "boot" command
7. On the initramfs image, back up the stock bootloader and firmware if
needed
8. Upload (or download) uboot.bin and sysupgrade.bin image to the device
9. Rplace the bootloader with a uboot.bin image
mtd write <uboot.bin image> bootloader
10. Perform sysupgrade with a sysupgrade.bin image
11. Wait ~120 seconds to complete flashing
Notes:
- All LEDs are connected to the Diodes PI4IOE5V9539LE I2C Expander chip.
(compatible with NXP PCA9539)
- The stock bootloader requires an unknown filesystem on firmware area
in the flash. Booting of OpenWrt from that filesystem cannot be
handled, so the bootloader needs to be replaced to mainline U-Boot
before OpenWrt installation.
- The data length of blocks in firmware image will be checked
(4M < threshold < 6M) on the stock WebUI of all versions, and
initramfs-factory.bin image of OpenWrt has the larger block data for
initramfs image. So that image cannot be applied to the stock WebUI
at all.
MAC addresses:
LAN : 98:F1:99:xx:xx:7C (config, 0x6 (hex))
WAN : 98:F1:99:xx:xx:7D (config, 0xc (hex))
2.4 GHz: 98:F1:99:xx:xx:7E (config, 0x0 (hex))
5 GHz : 98:F1:99:xx:xx:7F (config, 0x12 (hex))
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17584
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
INAGAKI Hiroshi [Fri, 3 Jan 2025 08:37:29 +0000 (17:37 +0900)]
ath79: update dtsi/dts for NEC Aterm devices based on QCA9558
Add more DT labels and move a USB hub node to dts files of Aterm devices
as a preparation for adding support of Aterm WG2200HP.
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17584
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
INAGAKI Hiroshi [Sat, 11 Jan 2025 16:40:19 +0000 (01:40 +0900)]
uboot-ath79: build U-Boot/qca9558_nec_aterm for NEC Aterm WG2200HP
Enable building U-Boot/qca9558_nec_aterm profile for NEC Aterm WG2200HP.
This model has almost the same hardware as the other Aterm devices based
on Qualcomm Atheros QCA9558.
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17584
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Mikhail Zhilkin [Sat, 22 Mar 2025 17:33:39 +0000 (17:33 +0000)]
mediatek: add support for netis NX31
This PR adds support for netis NX31 router.
Specification
-------------
- SoC : MediaTek MT7981BA dual-core ARM Cortex-A53 1.3 GHz
- RAM : 256 MiB DDR3
- Flash : SPI-NAND 128 MiB (ESMT)
- WLAN : MediaTek MT7976CN dual-band WiFi 6
- 2.4 GHz : b/g/n/ax, MIMO 2x2
- 5 GHz : a/n/ac/ax, MIMO 2x2
- Ethernet : 10/100/1000 Mbps x3 (LAN, MediaTek MT7531AE)
10/100/1000 Mbps x1 (WAN, SoC internal phy)
- USB : No
- Buttons : Mesh, Reset
- LEDs : 1x Power (blue), unmanaged
1x Status (blue), gpio-controlled
1x WiFi 2.4 GHz (blue), gpio-controlled
1x WiFi 5 GHz (blue), gpio-controlled
3x LAN activity (blue), switch-controlled
1x WAN activity (blue), gpio-controlled
- Power : 12 VDC, 1 A
Installation
------------
1. Connect to the router using ssh (user: admin, pass: web interface
password)
2. Make mtd backup:
cat /dev/mtd0 | gzip -1 -c > /tmp/mtd0_spi0.0.bin.gz
cat /dev/mtd1 | gzip -1 -c > /tmp/mtd1_BL2.bin.gz
cat /dev/mtd2 | gzip -1 -c > /tmp/mtd2_u-boot-env.bin.gz
cat /dev/mtd3 | gzip -1 -c > /tmp/mtd3_Factory.bin.gz
cat /dev/mtd4 | gzip -1 -c > /tmp/mtd4_FIP.bin.gz
cat /dev/mtd5 | gzip -1 -c > /tmp/mtd5_ubi.bin.gz
3. Download mtd backup from the /tmp dir of the router to your PC using
scp protocol
4. Upload OpenWrt 'bl31-uboot.fip', 'preloader.bin' images to the /tmp
dir of the router using scp protocol
5. Write FIP and BL2 (replace bootloader):
mtd write /tmp/openwrt-mediatek-filogic-netis_nx31-bl31-uboot.fip FIP
mtd write /tmp/openwrt-mediatek-filogic-netis_nx31-preloader.bin BL2
6. Place OpenWrt
'openwrt-mediatek-filogic-netis_nx31-initramfs-recovery.itb' image on
the tftp server (IP: 192.168.1.254)
7. Erase 'ubi' partition and reboot the router:
mtd erase ubi
reboot
8. U-Boot automatically boot OpenWrt recovery image from tftp server to
the RAM
9. Upload OpenWrt 'sysupgrade.itb' image to the /tmp dir of the router
(IP: 192.168.1.1) using scp protocol
10. Connect to the router using ssh and run:
sysupgrade -n openwrt-mediatek-filogic-netis_nx31-squashfs-sysupgrade.itb
Return to stock
---------------
1. Unpack stock BL2 and FIP partitions backup
2. Upload stock BL2 and FIP partitions backup to the /tmp dir of the
router using scp protocol
3. Connect to the router using ssh and run:
apk update && apk add kmod-mtd-rw
insmod mtd-rw i_want_a_brick=1
mtd unlock BL2
mtd unlock FIP
4. Restore backup:
mtd write /tmp/mtd4_FIP.bin FIP
mtd write /tmp/mtd1_BL2.bin BL2
5. Erase ubi and reboot:
mtd erase ubi
reboot
6. Power off the router
7. Press Reset button and power on the router. Release the button after
~10 sec
8. Navigate to U-Boot recovery web server (http://192.168.1.1/) and
upload the OEM firmware
Recovery
--------
1. Place OpenWrt
'openwrt-mediatek-filogic-netis_nx31-initramfs-recovery.itb' image on
the tftp server (IP: 192.168.1.254)
2. Press “Reset” button and power on the router. After ~10 sec release
the button.
3. Use OpenWrt initramfs system for recovery
MAC addresses
-------------
+---------+-------------------+-----------+
| | MAC | Algorithm |
+---------+-------------------+-----------+
| LAN | dc:xx:xx:d1:xx:18 | label |
| WAN | dc:xx:xx:d1:xx:1a | label+2 |
| WLAN 2g | de:xx:xx:11:xx:19 | |
| WLAN 5g | de:xx:xx:71:xx:19 | |
+---------+-------------------+-----------+
The LAN MAC was found in 'Factory', 0x1fef20
The WAN MAC was found in 'Factory', 0x1fef26
The WLAN 2g/5g MAC prototype was found in 'Factory', 0x4
Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/18324
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
George Sapkin [Fri, 4 Apr 2025 22:37:32 +0000 (01:37 +0300)]
tools/expat: bump to 2.7.1 to fix several CVEs
Addresses CVE-2024-8176 and CVE-2024-50602.
Changelog: https://github.com/libexpat/libexpat/blob/R_2_7_1/expat/Changes
Fixes: https://github.com/openwrt/packages/issues/26255
Fixes: https://github.com/advisories/GHSA-9hcv-xw76-m4h6
Fixes: https://github.com/advisories/GHSA-79wf-qgrg-2p6c
Signed-off-by: George Sapkin <george@sapk.in>
Link: https://github.com/openwrt/openwrt/pull/18421
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Fil Dunsky [Mon, 10 Mar 2025 23:57:43 +0000 (06:57 +0700)]
mediatek: filogic: add support for Huasifei WH3000
**Huasifei WH3000 eMMC / Fudy MT3000**
Portable Wi-Fi 6 travel router based on MediaTek MT7981A SoC.
MT7981B+MT7976CN+RTL8221B Dual Core 1.3GHZ
**Specifications**
SoC: Filogic 820 MT7981A (1.3GHz)
RAM: DDR4 1GB
Flash: eMMC 8GB
WiFi: 2.4GHz and 5GHz with 3 antennas
Ethernet:
1x WAN (10/100/1000M)
1x LAN (10/100/1000/2500M)
USB: 1x USB 3.0 port
Two buttons: power/reset and mode (BTN_0)
LEDS: blue, red, blue+red=pink
UART: 3.3V, TX, RX, GND / 115200 8N1
**Installation via U-Boot rescue**
1. Set static IP 192.168.1.2 on your computer and default route as 192.168.1.1
2. Connect to the WAN port and hold the reset button while booting the device.
3. Wait for the LED to blink 5 times, and release the reset button.
4. Open U-boot web page on your browser at http://192.168.1.1
5. Select the OpenWRT sysupgrade image, upload it, and start the upgrade.
6. Wait for the router to flash the new firmware.
7. Wait for the router to reboot itself.
**Installation via sysupgrade**
Just flash sysupgrade file via [LuCI upgrade page](http://192.168.1.1/cgi-bin/luci/admin/system/flash) without saving the settings.
**Installation via SSH**
Upload the file to the router `/tmp` directory, `ssh root@192.168.1.1` and issue a command:
```
sysupgrade -n /tmp/openwrt-mediatek-filogic-huasifei_wh3000-emmc-squashfs-sysupgrade.bin
```
**Factory MAC**
You can find your Factory MAC which is mentioned on the box at `/dev/mmcblck0p2` partition `factory` starting from `0x4`
```
dd if=/dev/mmcblk0p2 bs=1 skip=4 count=6 | hexdump -C
```
**Enlarging a partition**
Though device has 8GB eMMC, it uses only 2GB `/dev/mmcblck0p6` as `rootfs` for `/rom` and `/overlay` leaving `/dev/mmcblck0p7` as empty unused space.
```
sgdisk -p /dev/mmcblk0
```
```
Disk /dev/mmcblk0:
15269888 sectors, 7.3 GiB
Sector size (logical/physical): 512/512 bytes
Disk identifier (GUID):
2BD17853-102B-4500-AA1A-
8A21D4D7984D
Partition table holds up to 128 entries
Main partition table begins at sector 2 and ends at sector 33
First usable sector is 34, last usable sector is
14942174
Partitions will be aligned on 1024-sector boundaries
Total free space is 11197 sectors (5.5 MiB)
Number Start (sector) End (sector) Size Code Name
1 8192 9215 512.0 KiB 8300 u-boot-env
2 9216 13311 2.0 MiB 8300 factory
3 13312 21503 4.0 MiB 8300 fip
4 21504 29695 4.0 MiB 8300 config
5 29696 62463 16.0 MiB 8300 kernel
6 62464
4256767 2.0 GiB 8300 rootfs
7
4257792 14940159 5.1 GiB 8300
```
You can fix that by loading into `initramfs-kernel`, deleting empty `mmcblck0p7` partition and resizing `mmcblck0p6`
```
sysupgrade -F /tmp/openwrt-initramfs-kernel.bin
```
Install and run cfdisk
```
opkg update && opkg install cfdisk
cfdisk /dev/mmcblck0
```
- Select `mmcblck0p7` -> Delete
- Select `mmcblck0p6` -> Resize -> Write -> yes -> Quit
You will not see any difference in `cat /proc/partitions` after that but just flash a `sysupgrade` and you'll get the whole 7.3GB space for the `/overlay`.
Co-developed-by: hecatae <horus.ra@gmail.com>
Signed-off-by: Fil Dunsky <filipp.dunsky@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/18220
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Stijn Tintel [Tue, 18 Mar 2025 08:56:25 +0000 (10:56 +0200)]
arm-trusted-firmware-rockchip: support rk3588
ATF supports rk3588 since version 2.12, so let's enable it in
arm-trusted-firmware-rockchip.
We still need the TPL to initialize RAM, but keeping rk3588 in rkbin
would cause a duplicate package name, so rename rk3588 to rk3588-tpl in
rkbin.
Finally, point uboot-rockchip for rk3588 to bl31 built by this package,
and add a dependency on the new trusted-firmware-a-rk3588-tpl pacakge.
While this doesn't necessarily add features, we now no longer rely on
the rk3588_bl31_v1.45.elf blob provided by Rockchip, which is always a
good thing.
Tested on Radxa ROCK 5B+.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Stijn Tintel [Tue, 18 Mar 2025 08:53:46 +0000 (10:53 +0200)]
arm-trusted-firmware-rockchip: bump to 2.12.1 LTS
And remove no-warn-rwx-segments hack, as this is no longer needed and
actually causes build to fail. See also commit
c117d7a37a74
("include/trusted-firmware-a.mk: remove the no-warn-rwx-segments hack").
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Stijn Tintel [Mon, 24 Mar 2025 22:20:32 +0000 (00:20 +0200)]
include/trusted-firmware-a.mk: support LTS releases
TF-A LTS releases have an lts- prefix in their version tag. Introduce a
PKG_LTS variable to support these.
As the non-LTS tarbals do not contain the version prefix in the
directory, we need different PKG_BUILD_DIR for each variant:
➜ tar --list --file dl/trusted-firmware-a-v2.12.tar.gz | head -n1
trusted-firmware-a-2.12/
➜ tar --list --file dl/trusted-firmware-a-lts-v2.12.1.tar.gz | head -n1
trusted-firmware-a-lts-v2.12.1/
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Stijn Tintel [Mon, 24 Mar 2025 20:58:49 +0000 (22:58 +0200)]
rkbin: drop TFA_MAKE_FLAGS
The rkbin package doesn't compile anything, so TFA_MAKE_FLAGS is unused.
Suggested-by: Tianling Shen <cnsztl@immortalwrt.org>
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Russell Senior [Tue, 1 Apr 2025 12:07:01 +0000 (05:07 -0700)]
iproute2: update to v6.14.0
$ git log --no-merges --oneline v6.13.0..v6.14.0
fea1086c (tag: v6.14.0) v6.14.0
afbfd2f2 tc: nat: ffs should operation on host byte ordered data
667817b4 tc: nat: Fix mask calculation
e3f9681d ss: mptcp: subflow: display seq counters as decimal
5e113aba man: document tunnel options in ip-route.8.in
48717184 README.devel: clarify patch rules and syntax
99c119a0 ss: Tone down cgroup path resolution
41710ace uapi: update bpf.h
1db4f568 ip: vxlan: Support IFLA_VXLAN_RESERVED_BITS
fe4100df iproute2: add 'ip monitor acaddress' support
d009b68f Update kernel headers
0bd19d46 iprule: Add flow label support
35ae138e ip: route: Add IPv6 flow label support
3f8c7e7c tc: fq: add support for TCA_FQ_OFFLOAD_HORIZON attribute
49b8a727 Update kernel headers
19514606 iproute2: add 'ip monitor maddress' support
93360313 Update kernel headers
1f0f9deb ip: link: rmnet: add support for flag handling
Signed-off-by: Russell Senior <russell@personaltelco.net>
Robert Marko [Fri, 4 Apr 2025 10:25:21 +0000 (12:25 +0200)]
at91bootstrap: put at91bootstrap images into image staging directory
Currently, building at91 subtargets via image builder will fail as the
required built at91bootstrap is not present in the image builder at all
since its presumed to be in the binary directory which obviously does not
exist yet.
So, lets install the at91bootstrap binary into image staging directory and
use that instead
Link: https://github.com/openwrt/openwrt/pull/18414
Signed-off-by: Robert Marko <robimarko@gmail.com>
Robert Marko [Fri, 4 Apr 2025 09:55:08 +0000 (11:55 +0200)]
at91: put u-boot images into image staging directory
Currently, building at91 subtargets via image builder will fail as the
required built u-boot is not present in the image builder at all since its
presumed to be in the binary directory which obviously does not exist yet.
So, lets install the u-boot binary into image staging directory and use
that instead.
Link: https://github.com/openwrt/openwrt/pull/18414
Signed-off-by: Robert Marko <robimarko@gmail.com>
Erik Servili [Wed, 2 Apr 2025 21:01:16 +0000 (23:01 +0200)]
qualcommax: ipq60xx: add support for Netgear WAX610 and WAX610Y
Netgear WAX610 / WAX610Y is a 802.11ax AP claiming AX1800 support.
Specifications:
---------------
* CPU: Qualcomm IPQ6018 Quad core Cortex-A53
* RAM: 512MB
* Storage: Winbond W29N01HZBINF 128MB NAND
* Ethernet:
* 2.5GbE RJ45 port with PoE input
* WLAN:
* 2.4GHz/5GHz
* LEDs:
* Power: Dual-color LED (Green / Orange), Single-color LED (Blue)
* Ethernet: Dual-color LED (Green / Orange)
* 2.4Ghz WiFi: 2x Single-color LED (Blue, Green)
* 5Ghz WiFi: 2x Single-color LED (Blue, Green)
* Buttons:
* 1x Reset
* UART: 4-pin populated header
* Pinout 1 - VCC, 2 - GND, 3 - TX, 4 - RX
Installation:
=============
Web UI method
-------------
Set up the device using the stock web UI in local management mode.
Download the ui-factory.tar image.
* Enter the Management tab
* Select Maintenance->Upgrade->Firmware Upgrade
* Ensure the "Upgrade Options" field has "Local" selected
* Click "Browse File" and select the image
* Click "Upgrade" (NOT "Upgrade Now") at the bottom of the page
The device will install the image but reboot back into the vendor
firmware. Return the to Firmware Upgrade page as above and select
"Boot up Backup Firmware". The device should reboot into OpenWRT.
TFTP method
-----------
To flash via tftp, first place the initramfs image on the TFTP server.
setenv serverip <ip of tftp server>
setenv ipaddr <ip in same subnet as tftp server>
tftpboot netgear_wax610-initramfs-uImage.itb
bootm
This should boot OpenWRT. Once booted, flash the sysupgrade.bin image
using either luci or the command line.
Signed-off-by: Erik Servili <serverror@serverror.com>
Link: https://github.com/openwrt/openwrt/pull/18377
Signed-off-by: Robert Marko <robimarko@gmail.com>
Shiji Yang [Wed, 2 Apr 2025 00:03:20 +0000 (08:03 +0800)]
ath79: dts: disable redundant built-in watchdog
The built-in watchdog is redundant when the device has an external
GPIO based hardware watchdog. And there is a conflict that both of
them will attempt to register the same device entry in sysfs. This
resulted in the built-in watchdog being unable to be activated.
This patch explicitly disables the built-in watchdog for devices
that use GPIO watchdog to fix the error:
[ 1.779206] ath79-wdt
18060008.wdt: unable to register misc device, err=-16
[ 1.786355] ath79-wdt: probe of
18060008.wdt failed with error -16
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/18395
Signed-off-by: Robert Marko <robimarko@gmail.com>
Robert Marko [Fri, 4 Apr 2025 09:04:01 +0000 (11:04 +0200)]
at91: add USB kmods only for subtargets that support USB
Currently, kmod-usb-ohci,kmod-at91-udc and kmod-usb-gadget-eth are included
as the default packages for all at91 subtargets.
However, this is breaking image builder as kmod-at91-udc is not being built
on sama7 since it depends on USB_SUPPORT and sama7 does not have USB support
enabled in the kernel as its not supported upstream so its not even
selectable in the config.
So, move to include these as default packages only for sama5 and sama9x as
both of those have USB support enabled.
Fixes: #18407
Link: https://github.com/openwrt/openwrt/pull/18413
Signed-off-by: Robert Marko <robimarko@gmail.com>
Kyle Hendry [Sat, 11 Jan 2025 19:33:22 +0000 (11:33 -0800)]
bmips: add support for Actiontec T1200H
Specifications:
- SoC: Broadcom BCM63168 dual 400MHz MIPS
- Flash: 128MB NAND ESMT F59L1G81A
- RAM: 128MB DDR3
- Ethernet: 5x 1000M
- Wifi: BCM435F
- 1x USB 2.0 port
- 2x Button
- 11x LED
- Coax HPNA (unsupported)
- RJ11 xDSL (unsupported)
Install instructions:
The booloader will only install signed firmware so the image has to
be manually flashed.
- Set up a TFTP server on 192.168.1.0/24 to serve the initramfs image
- Interrupt the bootloader and run from RAM with
r 192.168.1.100:openwrt-bmips-bcm63268-actiontec_t1200h-initramfs.elf
- On the openwrt console, copy the wfi image using wget/tftp/scp, i.e
scp user@192.168.1.100:~/openwrt/bin/targets/bmips/bcm63268/openwrt-bmips-bcm63268-actiontec_t1200h-squashfs-cfe.bin /tmp/
- Erase half the flash partition where openwrt will be installed with
flash_erase -j /dev/mtd1 0 491
- Flash the openwrt image with
nandwrite -p /dev/mtd1 /tmp/openwrt-bmips-bcm63268-actiontec_t1200h-squashfs-cfe.bin
- Reboot
- Interrupt the bootloader again and use the c command to boot from
previous firmware if vendor image is loaded
Signed-off-by: Kyle Hendry <kylehendrydev@gmail.com>
[Minor improvements to DTS file]
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Álvaro Fernández Rojas [Wed, 2 Apr 2025 16:59:59 +0000 (18:59 +0200)]
bcm63xx-cfe: update to latest version
actiontec: t1200h: add cferam.000 file
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Shiji Yang [Wed, 2 Apr 2025 00:10:29 +0000 (08:10 +0800)]
ipq40xx: dts: fix "qcom,coexist-support" property type
Convert the property variable type of "qcom,coexist-support" from
u32 to u8 to match the definition in the dt-bindings document.
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/18393
Signed-off-by: Robert Marko <robimarko@gmail.com>
Shiji Yang [Wed, 2 Apr 2025 00:10:29 +0000 (08:10 +0800)]
ath10k-ct: remove "qcom,coexist-support" property type hack
The ath10k dt-binding property "qcom,coexist-support" was
explicitly defined as type uint8 since upstream commit
ed09c61eb19d ("dt-bindings: net: Convert ath10k to YAML").
Therefore, this hack patch no longer makes sense.
Link: https://github.com/torvalds/linux/commit/ed09c61eb19d9889780c791cb316ac76468f5186
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/18393
Signed-off-by: Robert Marko <robimarko@gmail.com>
Andrew LaMarche [Mon, 31 Mar 2025 17:00:28 +0000 (17:00 +0000)]
octeon: force pcs reset to fix qca833x traffic
There is a known bug with qca833x switches where they fail to pass
traffic without first resetting the PCS. U-Boot already has this fix,
though it uses a much newer networking stack from Marvell. This commit
backports the fix for OpenWrt.
References:
- https://github.com/u-boot/u-boot/blob/master/arch/mips/mach-octeon/cvmx-helper-sgmii.c#L197-L225
- https://github.com/u-boot/u-boot/blob/master/arch/mips/mach-octeon/cvmx-helper-sgmii.c#L701-L737
Signed-off-by: Andrew LaMarche <andrewjlamarche@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/18385
Signed-off-by: Robert Marko <robimarko@gmail.com>
Shiji Yang [Fri, 28 Mar 2025 16:10:25 +0000 (00:10 +0800)]
tools/xz: update to 5.8.0
Changelogs:
https://github.com/tukaani-project/xz/releases/tag/v5.8.0
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/18367
Signed-off-by: Nick Hainke <vincent@systemli.org>
Jan Hoffmann [Thu, 27 Feb 2025 19:43:26 +0000 (20:43 +0100)]
realtek: refactor RTL930x MAC config to fix PHY ports
Currently, network ports using PHYs get a link, but there is no traffic.
Make it work again by moving the MAC config to phylink_mac_link_up.
A similiar change has been previously applied for RTL83xx in commit
cd958d945be0 ("realtek: 6.6: refactor mac config and link up for
RTL83xx").
Fixes: https://github.com/openwrt/openwrt/issues/17010
Signed-off-by: Jan Hoffmann <jan@3e8.eu>
Tested-by: Christoph Krapp <achterin@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/18268
Signed-off-by: Sander Vanheule <sander@svanheule.net>
Tim Harvey [Mon, 27 Jan 2025 22:44:27 +0000 (14:44 -0800)]
mac80211: ath11k: Fix DMA buffer allocation to resolve SWIOTLB issues
Backport two commits to resolve issues with ath1kk causing it to fail
driver registration on iommuless systems with DRAM outside of 32bit
addressing such as a 4GiB imx8mm:
commit
1bcd20981834 ("wifi: ath11k: Fix DMA buffer allocation
to resolve SWIOTLB issues")
commit
eeadc6baf8b3 ("wifi: ath11k: Use dma_alloc_noncoherent
for rx_tid buffer allocation")
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Link: https://github.com/openwrt/openwrt/pull/17751
Signed-off-by: Robert Marko <robimarko@gmail.com>
jonathan brophy [Sun, 15 Dec 2024 00:36:29 +0000 (13:36 +1300)]
kernel: modules: reenable led-group-multi-color patch
This reverts commit
1375a7bae0d5e8dddb6b6cfe0584a399cd6c20b4.
This version does not activate the CONFIG_LEDS_CLASS_MULTICOLOR option,
this option is controlled by the generic target configuration.
Signed-off-by: jonathan brophy <professor_jonny@hotmail.com>
Link: https://github.com/openwrt/openwrt/pull/17277
[Reword commit message]
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
jonathan brophy [Thu, 26 Dec 2024 10:01:33 +0000 (23:01 +1300)]
stm32: add default kernel config option CONFIG_LEDS_CLASS_MULTICOLOR
The generic target configuration activates the
CONFIG_LEDS_CLASS_MULTICOLOR option. Do not deactivate it for the stm32
target.
Signed-off-by: jonathan brophy <professor_jonny@hotmail.com>
Link: https://github.com/openwrt/openwrt/pull/17277
[Reword commit message]
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Ivan Diaz [Mon, 10 Mar 2025 03:17:12 +0000 (22:17 -0500)]
ath79: move TP-Link RE450 v1 & v2 and RE355 v1 to tiny target
This restores sysupgrade support
Since OpenWrt 23.05, the firmware selector no longer provides sysupgrade
images for RE450 V1 & V2 and RE355 v1 due to image size constraints
(~5.7MB limit), making the generic build unusable.
This commit moves RE450 V1 & V2 to the tiny target, enabling:
- Smaller image builds within the flash size limit.
- Restored sysupgrade support via the firmware selector.
- A secure-by-default wireless setup while allowing full management via UCI.
- Officially supported images, reducing the need for custom (potentially insecure) builds.
This ensures users can install a functional OpenWrt build without compromising security defaults.
Signed-off-by: Ivan Diaz <diaz.it@icloud.com>
[Squashed the commits together and just copied the target definition
from the generic subtarget.]
Link: https://github.com/openwrt/openwrt/pull/18126
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Ivan Davydov [Tue, 4 Mar 2025 20:54:13 +0000 (23:54 +0300)]
ramips: mt76x8: add support for Keenetic Launcher (KN-1221)
Specification:
SoC: MediaTek MT7628AN
RAM: 128M DDR2, ESMT M14D128168A (2Y)
Flash: 32M, cFeon EN25QH256A (Dual Boot on OEM, concatenated on OpenWrt,
SPI)
Switch: MediaTek MT7628AN, 3 ports 100 Mbps
WiFi: MediaTek MT7628AN 2.4 GHz 802.11n
USB: 1 port USB 2.0
GPIO: 1 button (Wi-Fi & Reset on OEM, Reset on OpenWrt), 3 LEDs (Power,
Internet, Wi-Fi), USB port power controls
Disassembly:
There are 2 screws at the bottom near the LEDs hidden by rubber mounts.
After removing the screws, pry the gray plastic part around (it is secured
with latches) and remove it.
UART Interface:
The UART interface can be connected to the 5 pin located between LAN
ports and the WAN one.
Pins (from the second LAN port to the WAN one): VCC, TX, RX, NC, GND
Settings: 115200, 8N1
Flashing via TFTP:
1. Connect your PC and router to the first LAN port, configure PC
interface using IP 192.168.1.2, mask 255.255.255.0
2. Serve the firmware image (for OpenWrt it is *-squashfs-factory.bin)
renamed to KN-1221_recovery.bin via TFTP
3. Power up the router while pressing Wi-Fi button
4. Release Wi-Fi button when Power LED starts blinking
To revert back to OEM firmware:
The return to the OEM firmware is carried out by using the methods
described above with the help of the appropriate firmware image found on
osvault.keenetic.net.
When using OEM bootloader, the firmware image size cannot exceed the size
of one OEM «Firmware_x» partition or Kernel + rootFS size.
Signed-off-by: Ivan Davydov <lotigara@lotigara.ru>
Link: https://github.com/openwrt/openwrt/pull/18164
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
John Audia [Sun, 30 Mar 2025 12:40:06 +0000 (08:40 -0400)]
kernel: bump 6.6 to 6.6.85
Changelog: https://cdn.kernel.org/pub/linux/kernel/v6.x/ChangeLog-6.6.85
Removed upstreamed:
bcm27xx/patches-6.6/950-1498-dts-bcm2711-PL011-UARTs-are-actually-r1p5.patch[1]
bcm27xx/patches-6.6/950-1551-drm-v3d-Don-t-run-jobs-that-have-errors-flagged-in-i.patch[2]
Manually rebased:
bcm27xx/patches-6.6/950-1512-dts-bcm2711-Don-t-mark-timer-regs-unconfigured.patch
All other patches automatically rebased.
1. https://web.git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v6.6.85&id=
61820187b3ef5a15aed7ef49ed1fcc13398b449c
2. https://web.git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v6.6.85&id=
7cd375d46afcce906cfcddf5aec6b318199d1f16
Build system: x86/64
Build-tested: flogic/xiaomi_redmi-router-ax6000-ubootmod, ramips/tplink_archer-a6-v3, x86/64
Run-tested: flogic/xiaomi_redmi-router-ax6000-ubootmod, ramips/tplink_archer-a6-v3, x86/64
Signed-off-by: John Audia <therealgraysky@proton.me>
Link: https://github.com/openwrt/openwrt/pull/18379
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Shiji Yang [Sat, 22 Feb 2025 06:15:12 +0000 (14:15 +0800)]
ath10k-ct-firmware: remove QCA9888 board file symbolic link
Although ath10k pre-calibration data and board description file
have similar data structures, they are completely different things.
Therefore, let's remove these incorrect and confusing links.
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/18069
Signed-off-by: Robert Marko <robimarko@gmail.com>
Qingfang Deng [Sat, 8 Mar 2025 18:00:14 +0000 (02:00 +0800)]
kernel: Mediatek: fix EEE registers init
After booting, a "transmit queue 0 timed out" warning followed by a
register dump was observed. The dump indicates that mtk_hw_init() does
not initialize the EEECR during probe. This occurs because the
netdev is allocated in mtk_add_mac(), which is called after
mtk_hw_init(). Consequently, the EEECR register remains uninitialized
until a reset is triggered, causing mtk_hw_init() to run again with a
valid netdev, at which point the register is finally set.
To address this, instead of modifying the probe sequence, latch the Tx
LPI enable state and timer value, and move the EEECR register
initialization to mtk_mac_link_up() to ensure proper setup when the
interface comes up.
Additionally, the splat reveals that LPI functionality is controlled by
the MAC_MCR_EEE bits in the MCR register. Update mtk_set_eee() to
modify these bits accordingly.
Fixes: d8315d5358d5 ("kernel: backport Mediatek SoC EEE support")
Fixes: edddbaf79ccf ("kernel: Mediatek: set default EEE Tx LPI timer")
Signed-off-by: Qingfang Deng <dqfext@gmail.com>
projects / openwrt / staging / blocktrron.git / log