Bluetooth: Simplify UUIDs clearing code

The code for clearing the UUIDs list can be simplified by using
list_for_each_entry_safe instead of list_for_each_safe.

Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>

Bluetooth: Store UUIDs in the same order that they were added

We should be encoding UUIDs to the EIR data in the same order that they
were added to the kernel, i.e. each UUID should be added to the end of
the UUIDs list. This patch fixes the issue by using list_add_tail
instead of list_add for storing the UUIDs.

Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>

wil6210: fix wil_vring_init_tx status

In case vring setup with the firmware failed,
success status was returned. fix it.

Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

wil6210: Never delete Rx chain with firmware

Firmware crash on attempt to delete Rx chain.
Driver part of Rx chain removed only in preparation for the target reset;
as reset is the only flow that removes Rx chain in the firmware.

Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

wil6210: checkpatch warnings

Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

wil6210: fix checkpatch CamelCase warnings

Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

wil6210: Reorder reset preparation sequence

Disable interrupts first to prevent spurious WMI events arrival

Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

wil6210: Separate common code for mbox regs caching to function

Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

wil6210: Fix "don't scan after connect" logic

When connect times out, scan was not re-enabled.

Strictly say, it is firmware issue - it should issue "disconnect"
event but it does not. Compensate in the driver.

Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

wil6210: Call skb_orphan() right before Rx indication

Other parts of Rx path (BACK logic) will need to access associated data

Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

wil6210: Fix: Tx stall

Due to multi-tx-queue design, wil_start_xmit() used to be executed
concurrently for different queues. Then, these transmits delivered
to the same queue, creating race.

As result, Tx descriptor may be skipped, causing stall in hardware.

Convert to single Tx queue fixes it.

Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

wil6210: Count Tx statistics on Tx completion

This allows to account for Tx errors

Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

wil6210: Refactor rx init/fini

Move WMI related operations to wmi.c as helper functions

Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

wil6210: remove raw wil_dbg() calls

Introduce debug category "MISC", convert all raw wil_dbg() to this category.
This improves dynamic debug manageability

Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

wil6210: rearrange IRQ debug printing

Make printings from IRQ appears in dmesg in chronological order

Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

wil6210: Detect FW error

In the firmware, added is ability to report internal errors using IRQ.

Catch this IRQ and notify user space via netlink

User space get notified like (udevadm monitor --kernel --property):

KERNEL[12660.320520] change   /devices/pci0000:00/0000:00:1c.1/0000:02:00.0/0000:03:01.0/0000:05:00.0/net/wlan12 (net)
ACTION=change
DEVPATH=/devices/pci0000:00/0000:00:1c.1/0000:02:00.0/0000:03:01.0/0000:05:00.0/net/wlan12
DEVTYPE=wlan
EVENT=FW_ERROR
IFINDEX=6
INTERFACE=wlan12
SEQNUM=2489
SOURCE=wil6210
SUBSYSTEM=net

Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mwifiex: avoid out of bounds access in mwifiex_get_common_rates.

Check that the array indexes are in-bounds before accessing the rate2 and tmp
arrays.

Found with the following semantic patch:

<smpl>
@@
identifier t;
identifier idx;
expression E;
statement S;
@@
* for (... ; <+... t[idx] ...+> && idx < E ; ...)
S
</smpl>

Signed-off-by: Cyril Roelandt <tipecaml@gmail.com>
Acked-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rtlwifi: Eliminate two empty routines

Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

net: iwlegacy: remove unused variable

Fix:

drivers/net/wireless/iwlegacy/4965.c: In function ‘il4965_post_associate’:
drivers/net/wireless/iwlegacy/4965.c:1751:25: warning: variable ‘conf’ set but
not used [-Wunused-but-set-variable]

seen when building allmodconfig on x86_64 with W=1 by removing the unused
variable.

Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

iwlegacy: fix antenna bitmask

This patch is based on "iwlwifi: fix antenna bitmask".
(362b0563b28506d53)

Like the new iwlagn devices, the old 4965N device only
supports a maximum of three antennas. Hence only three
bits are used, the fourth bit is likely the A-MPDU
indicator.

Cc: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

bcma: add gpio_to_irq

The old bcm47xx gpio code had support for gpio_to_irq, but the new
code did not provide this function, but returned -ENXIO all the time.
This patch adds the missing function.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ssb: add gpio_to_irq

The old bcm47xx gpio code had support for gpio_to_irq, but the new
code did not provide this function, but returned -ENXIO all the time.
This patch adds the missing function.

arch/mips/bcm47xx/wgt634u.c calls gpio_to_irq() and got the correct irq
number with the old gpio handling code. With this patch the code in
wgt634u.c should work again. I do not have a wgt634u to test this.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mwifiex: do not overwrite error code from lower layer driver

Instead of converting it to a bogus error code -1, we should
return the original error code from lower layer driver. This
error code will be printed so it may give user some clues on
what has happened.

Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mwifiex: don't return zero on failure paths in mwifiex_pcie_init()

If pci_iomap() fails in mwifiex_pcie_init(), it breaks off initialization,
deallocates all resources, but returns zero.
The patch adds -EIO as return value in this case.

Found by Linux Driver Verification project (linuxtesting.org).

Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Acked-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rtl8723ae: Fix misspellings sucess->success

Signed-off-by: Anatol Pomozov <anatol.pomozov@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mwl8k: Do not call STA specific cmds not supported by the AP fw

While using STA mode in the AP firmware, avoid
calling some firmware commands which are not
supported by the AP firmware.

Signed-off-by: Yogesh Ashok Powar <yogeshp@marvell.com>
Signed-off-by: Nishant Sarmukadam <nishants@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mwl8k: Choose interface specific calls on vif type

Choose interface specific function calls
based on interface type instead of
firmware types.

Signed-off-by: Yogesh Ashok Powar <yogeshp@marvell.com>
Signed-off-by: Nishant Sarmukadam <nishants@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mwl8k: Add/Del self entry for AP interface only

Add and delete self entry in the firmware sta database
for AP interface only. We do not need such an entry for
STA interface.

Signed-off-by: Yogesh Ashok Powar <yogeshp@marvell.com>
Signed-off-by: Nishant Sarmukadam <nishants@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mwl8k: Enable hw encryption for STA mode on AP fw

Firmware supports hardware encryption feature
for the station interface running on AP
firmware.

Signed-off-by: Yogesh Ashok Powar <yogeshp@marvell.com>
Signed-off-by: Nishant Sarmukadam <nishants@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mwl8k: set mac type to MWL8K_MAC_TYPE_SECONDARY_CLIENT

Set mac type for station interface on AP firmware
as secondary. This allows the firmware to set specific
characteristics for the STA interface.

Signed-off-by: Yogesh Ashok Powar <yogeshp@marvell.com>
Signed-off-by: Nishant Sarmukadam <nishants@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mwl8k: Allow adding station interface on AP firmware

When user wants to add a station interface when
AP firmware is loaded & in-use, allow creating
it and also notify user about the same.

Allow adding max one STA interface for AP fw.

Signed-off-by: Yogesh Ashok Powar <yogeshp@marvell.com>
Signed-off-by: Nishant Sarmukadam <nishants@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mwl8k: Announce simultaneous AP-STA support on AP fw

Specify the STA support in iface_limit and
in wihpy->interface_modes

Signed-off-by: Yogesh Ashok Powar <yogeshp@marvell.com>
Signed-off-by: Nishant Sarmukadam <nishants@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mwl8k: Move tx/rx antenna configuration to mwl8k_probe_hw

This avoids calling mwl8k_cmd_rf_antenna functions every
time mwl8k_config function is called.

Signed-off-by: Yogesh Ashok Powar <yogeshp@marvell.com>
Signed-off-by: Nishant Sarmukadam <nishants@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mwl8k: Do not call mwl8k_cmd_set_rf_channel unconditionally

Avoid calling mwl8k_cmd_set_rf_channel unconditionally
by checking IEEE80211_CONF_CHANGE_CHANNEL.

Signed-off-by: Yogesh Ashok Powar <yogeshp@marvell.com>
Signed-off-by: Nishant Sarmukadam <nishants@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mwl8k: Stop bsses before hw specific commands

For the commands, that might change the hw characteristics
of the PHY device, stop the running bsses and resume them
once command is complete.

Signed-off-by: Yogesh Ashok Powar <yogeshp@marvell.com>
Signed-off-by: Nishant Sarmukadam <nishants@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

bcma: register platform device for parallel flash

Signed-off-by: John W. Linville <linville@tuxdriver.com>

ssb: register platform device for parallel flash

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ssb: trivial: use pflash helper variable

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rt2x00: allow AP and mesh mode to operate simultaneously

Allow AP and Mesh mode to operate concurrently using
single radio. Verify this using fonera 2.0n featuring
RT3052 chipset and also TP-LINK TL-WN727N featuring
RT5370 chipset.

Signed-off-by: Chun-Yeow Yeoh <yeohchunyeow@gmail.com>
Acked-by: Helmut Schaa <helmut.schaa@googlemal.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rt2x00: remove NOTICE

We use this macro only on 3 places - remove it and replace by other
appropriate macros for printing messages.

Signed-off-by: Stanislaw Gruszka <stf_xl@wp.pl>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rt2800usb: move "TX status missed" messages to debug level

Those messages can flood in dmesg, so do not print them by default.

Signed-off-by: Stanislaw Gruszka <stf_xl@wp.pl>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rt2x00: print warning, notice and info as default

Some messages provide useful information, but are disabled without
CONFIG_RT2X00_DEBUG=y, so enable them by default

Signed-off-by: Stanislaw Gruszka <stf_xl@wp.pl>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: Update spectral scan output data

The sample data received through the spectral scan can be either in big or
little endian byteorder. This information isn't stored in the output file.
Therefore it is not possible for the analyzer software to find the correct byte
order.

It is relative common to get the data from a low end AP in big endian mode and
transfer it to another computer in little endian mode to analyze it. Therefore,
it would be better to store it in network (big endian) byte order.

The extension of the 8 bit bins for each bin to 16 bit is not necessary. This
operation can be done in userspace or on a different machine. Instead the
max_exp defining the amount of shifting required for each bin is exported to
userspace.

The change of the output format requires a change of the type in the sample
tlv to allow the userspace program to correctly detect the bin format.

Reported-by: Zefir Kurtisi <zefir.kurtisi@neratec.com>
Signed-off-by: Sven Eckelmann <sven@open-mesh.com>
[siwu@hrz.tu-chemnitz.de: squashed patches, update commit message, rebase, fix endianess bug]
Signed-off-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: Mathias Kretschmer <mathias.kretschmer@fokus.fraunhofer.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: reorder error codes for spectral

When using the spectral scan feature, frames with phy errors are
returned for further processing to the driver. However, if the frames
also have an invalid CRC (which seems to happen quite often), the frame
is marked with bad CRC and not with the PHY error bit. The FFT
processing function will thus miss the frames.

Fix this by changing the precedence in error marking.

Signed-off-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: Mathias Kretschmer <mathias.kretschmer@fokus.fraunhofer.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: drop spectral packets after processing them

Spectral packets are "bogus" packets and should not be further evaluated
by the RX path.

Statistics are added to keep track of these packets.

Signed-off-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: Mathias Kretschmer <mathias.kretschmer@fokus.fraunhofer.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: add debug parameters for spectral scan

Export the various parameters to userspace.

Signed-off-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: Mathias Kretschmer <mathias.kretschmer@fokus.fraunhofer.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mwifiex: fix invalid access of PCIe RxBD ring buffer descriptor

This patch fixes invalid access of RxBD ring buffer descriptor's
length and flag inside PCIe send_data_complete() routine. We are
supposed to modify TxBD buffer descriptor's length and flag here.

Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rt2x00: print chip and firmware version by default

Signed-off-by: Stanislaw Gruszka <stf_xl@wp.pl>
Tested-by: Xose Vazquez Perez <xose.vazquez@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

drivers/net/wireless/iwlegacy/4965-mac.c: adjust duplicate test

Delete successive tests to the same location.  This looks like simple code
duplication.

A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)

// <smpl>
@s exists@
local idexpression y;
expression x,e;
@@

*if ( \(x == NULL\|IS_ERR(x)\|y != 0\) )
 { ... when forall
   return ...; }
... when != \(y = e\|y += e\|y -= e\|y |= e\|y &= e\|y++\|y--\|&y\)
    when != \(XT_GETPAGE(...,y)\|WMI_CMD_BUF(...)\)
*if ( \(x == NULL\|IS_ERR(x)\|y != 0\) )
 { ... when forall
   return ...; }
// </smpl>

Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Merge branch 'for-john' of git://git./linux/kernel/git/iwlwifi/iwlwifi-next

Merge branch 'for-john' of git://git./linux/kernel/git/jberg/mac80211-next

Merge branch 'for-upstream' of git://git./linux/kernel/git/bluetooth/bluetooth-next

Merge branch 'for-linville' of git://git./linux/kernel/git/luca/wl12xx

Conflicts:
drivers/net/wireless/ti/wlcore/main.c

Merge branch 'master' of git://git./linux/kernel/git/linville/wireless

Conflicts:
drivers/net/wireless/ath/ath9k/main.c
drivers/net/wireless/iwlwifi/dvm/tx.c

mac80211: fix mesh_sta_info_get() reshuffle damage

Before "mac80211: clean up mesh sta allocation warning"
was applied, mesh_sta_info_get() was reshuffled to please
sparse. As a result we neglect to initialize newly created
STAs. Fix this.

Signed-off-by: Thomas Pedersen <thomas@cozybit.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

cfg80211/nl80211: add API for MAC address ACLs

Add API to enable drivers to implement MAC address based
access control in AP/P2P GO mode. Capable drivers advertise
this capability by setting the maximum number of MAC
addresses in such a list in wiphy->max_acl_mac_addrs.

An initial ACL may be given to the NL80211_CMD_START_AP
command and/or changed later with NL80211_CMD_SET_MAC_ACL.

Black- and whitelists are supported, but not simultaneously.

Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
[rewrite commit log, many cleanups]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

cfg80211: Move the definition of struct mac_address up

struct mac_address will be used by ACL related configuration ops.

Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

mac80211: avoid a build warning

gcc cannot prove that the value of sdata->vif.type does not
change between the switch() statement and the second
comparison to NL80211_IFTYPE_AP, causing a harmless
warning.
Slightly reordering the code makes the warning go away
with no functional change.

Without this patch, building ARM at91sam9g45_defconfig with
gcc-4.6 results in:

net/mac80211/tx.c: In function 'ieee80211_subif_start_xmit':
net/mac80211/tx.c:1797:22: warning: 'chanctx_conf' may be used uninitialized in this function [-Wuninitialized]

Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Johannes Berg <johannes@sipsolutions.net>
Cc: "John W. Linville" <linville@tuxdriver.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

mac80211: remove redundant check

There's no need to have two checks for "associated"
in ieee80211_sta_restart(), make the first one locked
to not race (unlikely at this point during resume)
and remove the second check.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>

cfg80211: fix channel check in cfg80211_can_use_iftype_chan

In commit "cfg80211: check radar interface combinations" a regression
was introduced which might lead to NULL dereference if the argument
chan = NULL, which might happen in IBSS/wext case (and probably
others).

Signed-off-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

mac80211: support mesh rate updates

An existing mesh station entry may change its rate
capabilities, so call rate_control_rate_update() to notify
the rate control.

Signed-off-by: Thomas Pedersen <thomas@cozybit.com>
[fix compilation]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

mac80211: clean up mesh sta allocation warning

This refactoring fixes a "scheduling while atomic" warning
when allocating a mesh station entry while holding the RCU
read lock. Fix this by creating a new function
mesh_sta_info_get(), which correctly handles the locking
and returns under RCU.

Also move some unnecessarily #ifdefed mesh station init
code from sta_info_alloc() to __mesh_sta_info_alloc().

Signed-off-by: Thomas Pedersen <thomas@cozybit.com>
[change code flow to make sparse happy]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

ieee80211: define AKM suite selectors type 5, 6 and 7

Reference: IEEE 802.11-2012 8.4.2.27.3 "AKM suites"

Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

mac80211: fix aggregation state with current drivers

For drivers that don't actually flush their queues when
aggregation stop with the IEEE80211_AMPDU_TX_STOP_FLUSH
or IEEE80211_AMPDU_TX_STOP_FLUSH_CONT reasons is done,
like iwlwifi or iwlegacy, mac80211 can then transmit on
a TID that the driver still considers busy. This happens
in the following way:

 - IEEE80211_AMPDU_TX_STOP_FLUSH requested
 - driver marks TID as emptying
 - mac80211 removes tid_tx data, this can copy packets
   to the TX pending queues and also let new packets
   through to the driver
 - driver gets unexpected TX as it wasn't completely
   converted to the new API

In iwlwifi, this lead to the following warning:

WARNING: at drivers/net/wireless/iwlwifi/dvm/tx.c:442 iwlagn_tx_skb+0xc47/0xce0
Tx while agg.state = 4
Modules linked in: [...]
Pid: 0, comm: kworker/0:0 Tainted: G        W   3.1.0 #1
Call Trace:
 [<c1046e42>] warn_slowpath_common+0x72/0xa0
 [<c1046f13>] warn_slowpath_fmt+0x33/0x40
 [<fddffa17>] iwlagn_tx_skb+0xc47/0xce0 [iwldvm]
 [<fddfcaa3>] iwlagn_mac_tx+0x23/0x40 [iwldvm]
 [<fd8c98b6>] __ieee80211_tx+0xf6/0x3c0 [mac80211]
 [<fd8cbe00>] ieee80211_tx+0xd0/0x100 [mac80211]
 [<fd8cc176>] ieee80211_xmit+0x96/0xe0 [mac80211]
 [<fd8cc578>] ieee80211_subif_start_xmit+0x348/0xc80 [mac80211]
 [<c1445207>] dev_hard_start_xmit+0x337/0x6d0
 [<c145eee9>] sch_direct_xmit+0xa9/0x210
 [<c14462c0>] dev_queue_xmit+0x1b0/0x8e0

Fortunately, solving this problem is easy as the station
is being destroyed, so such transmit packets can only
happen due to races. Instead of trying to close the race
just let the race not reach the drivers by making two
changes:
 1) remove the explicit aggregation session teardown in
    the managed mode code, the same thing will be done
    when the station is removed, in __sta_info_destroy.
 2) When aggregation stop with AGG_STOP_DESTROY_STA is
    requested, leave the tid_tx data around as stopped.
    It will be cleared and freed in cleanup_single_sta
    later, but until then any racy packets will be put
    onto the tid_tx pending queue instead of transmitted
    which is fine since the station is being removed.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>

mac80211: provide the vif in rssi_callback

Since drivers can support several BSS / P2P Client
interfaces, the rssi callback needs to inform the driver
about the interface teh rssi event relates to.

Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

iwlwifi: provide RX page order

When the pages are to be used by front-end, it may need
to know the page order, provide it.

Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

iwlwifi: update copyright

Update Copyright notices to 2013.

Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Bluetooth: Add support for reading LE supported states

The LE supported states indicate the states and state combinations that
the link layer supports. This is important information for knowing what
operations are possible when dealing with multiple connected devices.
This patch adds reading of the supported states to the HCI init
sequence.

Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>

Bluetooth: Add support for reading LE White List Size

The LE White List Size is necessary to be known before attempting to
feed the controller with any addresses intended for the white list. This
patch adds the necessary HCI command sending to the HCI init sequence.

Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>

Bluetooth: Add LE Local Features reading support

To be able to make the appropriate decisions for some LE procedures we
need to know the LE features that the local controller supports.
Therefore, it's important to have the LE Read Local Supported Features
HCI comand as part of the HCI init sequence.

Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>

Bluetooth: Fix returning proper cmd_complete for mgmt_block/unblock

The Block/Unblock Device Management commands should return Command
Complete instead of Command Status whenever possible so that user space
can distinguish exactly which command failed in the case of multiple
commands. This patch does the necessary changes in the command handler
to return the right event to user space.

Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>

Bluetooth: Fix returning proper cmd_complete for mgmt_disconnect

The Disconnect Management command should return Command Complete instead
of Command Status whenever possible so that user space can distinguish
exactly which command failed in the case of multiple commands. This
patch does the necessary changes in the disconnect command handler to
return the right event to user space.

Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>

Bluetooth: Fix checking for valid disconnect parameters in unpair_device

The valid values for the Disconnect parameter in the Unpair Device
command are 0x00 and 0x01. If any other value is encountered the command
should fail with the appropriate invalid params response.

Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>

Bluetooth: Fix checking for valid address type values in mgmt commands

This patch adds checks for valid address type values passed to mgmt
commands. If an invalid address type is encountered the code will return
a proper invalid params response.

Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>

Bluetooth: Add helper functions for testing bdaddr types

This patch adds two helper functions to test for valid bdaddr type
values. These will be particularely useful in the mgmt code to check
that user space has passed valid values to the kernel.

Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>

Bluetooth: Check for valid key->authenticated value for LTKs

This patch adds necessary checks for the two allowed values of the
authenticated parameter of each Long Term Key, i.e. 0x00 and 0x01. If
any other value is encountered the valid response is to return invalid
params to user space.

Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>

Bluetooth: Refactor valid LTK data testing into its own function

This patch refactors valid LTK data testing into its own function. This
will help keep the code readable since there are several tests still
missing that need to be done on the LTK data.

Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>

Bluetooth: Fix checking for proper key->master value in Load LTKs

The allowed values for the key->master parameter in the Load LTKs
command are 0x00 and 0x01. If there is a key in the list with some other
value the command should fail with a proper invalid params response.

Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>

Bluetooth: Fix returning proper mgmt status for Load LTKs

Failures of mgmt commands should be indicated with valid mgmt status
codes, and EINVAL is not one of them. Instead MGMT_STATUS_INVALID_PARAMS
should be returned.

Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>

Bluetooth: Fix checking for correct mgmt_load_link_keys parameters

The debug_keys parameter is only allowed to have the values 0x00 and
0x01. Any other value should result in a proper command status with
MGMT_STATUS_INVALID_PARAMS.

Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>

Bluetooth: Fix pair device command reply if adapter is powered off

According to Bluetooth Management API specification Pair Device Command
should generate command complete event on both success and failure.
This fix replying with command status (which lacks address info) when
adapter is powered off.

Signed-off-by: Szymon Janc <szymon.janc@tieto.com>
Acked-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>

Bluetooth: Fix Class of Device indication when powering off

When a HCI device is powered off the Management interface specification
dictates that the class of device value is indicated as zero. This patch
fixes sending of the appropriate class of device changed event when a
HCI device is powered off.

Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>

ath9k_hw: remove a useless WARN_ON

&ah->curchan->ani can never be NULL

Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k_hw: reduce struct ar5416AniState size

It is kept per-channel, so removing unnecessary (or constant) fields from
it can save quite a bit of memory.

Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k_hw: remove ath9k_hw_ani_setup and its variables

They are no longer needed for ANI functionality

Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k_hw: make the initval parameter to ath9k_hw_write_array const

Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: use ath_tx_process_buffer instead of open-coding similar code

Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: clean up processing of pending tx frames on reset

Dropping packets from aggregation sessions is usually not a good idea, as
it might upset the synchronization of the BlockAck receive window of the
remote node. The use of the retry_tx parameter to reset/tx-drain functions
also seemed a bit arbitrary.
This patch removes this parameter altogether and ensures that pending tx
frames are not dropped for no good reason.

Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: stop rx after tx

Completing frame transmission can fail if the rx engine is stopped
prematurely, as the hw might be waiting for an ACK from the other side.
Shutting down tx before rx might make the DMA shutdown more reliable.

Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

net: wireless/rtlwifi: fix uninitialized variable issue

The use of variable packet_beacon might be uninitialized in the three files.

Signed-off-by: Cong Ding <dinggnu@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

iwlegacy: don't return zero on failure paths in il4965_pci_probe()

If hardware is not ready, il4965_pci_probe() breaks off initialization,
deallocates all resources, but returns zero.
The patch adds -EIO as return value in this case.

Found by Linux Driver Verification project (linuxtesting.org).

Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mwl8k: don't return zero on failure paths in mwl8k_probe[_hw]()

If pci_iomap() fails in mwl8k_probe(), it breaks off initialization,
deallocates all resources, but returns zero.
There is a similar issue when priv->rxd_ops is NULL in mwl8k_probe_hw().

The patch adds proper error code return values.

Found by Linux Driver Verification project (linuxtesting.org).

Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mwifiex: correction in status codes used for association failure

When AP responds with appropriate status code, we forward that
code correctly to cfg80211. But sometimes when there is no
response from AP, our firmware uses proprietary status codes.
We will map authentication timeout to WLAN_STATUS_AUTH_TIMEOUT
and other proprietary codes to WLAN_STATUS_UNSPECIFIED_FAILURE.

Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rt2x00: Improve TX status handling for BlockAckReq frames

Since rt2800 hardware isn't capable of reporting the TX status of
BlockAckReq frames implement the TX status handling of BARs in
rt2x00lib. We keep track of all BARs that are send out and try to
match incoming BAs to the appropriate BARs. This allows us to report a
more or less accurate TX status for BAR frames which in turn improves
BA session stability.

This is loosley based on Christian Lamparter's patch for carl9170
"carl9170: fix HT peer BA session corruption".

We have to walk the list of pending BARs for every rx'red BA even
though most BAs don't belong to any of these BARs as they are just
acknowledging an AMPDU. To keep that overhead low use RCU which allows
us to walk the list of pending BARs without the need to acquire a lock.
This however requires us to _copy_ relevant information from the BAR
(RA, TA, control field, start sequence number) into our BAR list entry.

Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Tested-by: Andreas Hartmann <andihartmann@01019freenet.de>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

prism54: bug in getting auth type

There is a missing break statement so SHARED_KEY authentication doesn't
work.

Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

b43: N-PHY: fix gain in b43_nphy_get_gain_ctl_workaround_ent()

There were no break statements in this switch statement so everything
used the default settings.  Per Walter Harms's suggestion, I've replaced
the switch statement and done a little cleanup.

Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

drivers/net/wireless: need consider the not '\0' terminated string.

  in ray_cs.c:
    the a_current_ess_id is "Null terminated unless ESSID_SIZE long"
    so we need buffer it with '\0' firstly, before using strlen or %s.

  additional information:
    in drivers/net/wireless/rayctl.h:
      "NULL terminated unless 32 long" is a comment at line 616, 664
      ESSID_SIZE is 32, at line 190
    in include/uapi/linux/wireless.h:
      IW_ESSID_MAX_SIZE is also 32
    in drivers/net/wireless/ray_cs.c:
      use strncpy for it, without '\0' terminated, at line 639
      use memcpy for it, assume not '\0' terminated in line 1092..1097
      buffer it with '\0' firstly, before using %s, in line 2576, 2598..2600

Signed-off-by: Chen Gang <gang.chen@asianux.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k_hw: fix RF bank initialization

ar900*_init_mode_regs needs to be called before RF banks are allocated,
otherwise the storage size of RF banks isn't known. This patch fixes
a memory overrun that can show up as a crash on unloading the module.

Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Merge branch 'for-john' of git://git./linux/kernel/git/jberg/mac80211-next

Merge branch 'for-john' of git://git./linux/kernel/git/iwlwifi/iwlwifi-next