brcmfmac: Correct header debug dump for sdio tx hdrs.

Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

brcmfmac: remove unused variable data_len from brcmf_sdio_bus_txdata()

The local variable data_len is assigned but never used so get rid
of it.

Reviewed-by: Daniel (Deognyoun) Kim <dekim@broadcom.com>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

brcmfmac: fix use of skb control buffer in SDIO driver part

The SDIO driver has a 16-bit field defined in the skbuff control buffer.
However, it is accessed as a u32 overwriting other control info. Another
issue is that the field is not initialized for networking packets, but
the control buffer content is unspecified as other networking layers can
use it.

Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: Daniel (Deognyoun) Kim <dekim@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

brcmfmac: Make firmeware roaming a module param.

Internal firmware roaming is enabled by default. This patch
makes it possible to disable internal firmware roaming by
specifying roamoff=1 as module param.

Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Daniel (Deognyoun) Kim <dekim@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k_htc: use ath9k_cmn_reload_chainmask

Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: move ath9k_reload_chainmask_settings to common

Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k-common: set maxstream=1 for ar9271

Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k_htc: use ath9k_cmn_setup_ht_cap

Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: move setup_ht_cap to common-init

and rename it to ath9k_cmn_setup_ht_cap

Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k_htc: use ath9k_cmn_init_channels_rates

and ath_common sbands.

Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: move ath9k_init_channels_rates to common-init

and rename it to ath9k_cmn_init_channels_rates.
sbands are move to ath_common as well.

Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mwl8k: Adding support to gather survey per channel

Survey stats such as channel busy time, rx busy time
and noise are collected when sw_scan starts for every
switched new channel. This happens till sw_scan stops.

All the collected stats are shared up when get_survey()
is called.

This implements support for ACS feature from Hostapd.

Signed-off-by: Yogesh Ashok Powar <yogeshp@marvell.com>
Signed-off-by: Nishant Sarmukadam <nishants@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mwl8k: Implement sw_scan start/stop cbs

Implement sw_scan start and stop callbacks.
Reset BBP registers for channel, RX busy and
average noise stats which clear on read.

Signed-off-by: Yogesh Ashok Powar <yogeshp@marvell.com>
Signed-off-by: Nishant Sarmukadam <nishants@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mwl8k: Adding support to access BBP registers

Adding AP firmware command to access BBP
regs. This will be used for retrieving
different counters CCA/RX needed for ACS

Signed-off-by: Yogesh Ashok Powar <yogeshp@marvell.com>
Signed-off-by: Nishant Sarmukadam <nishants@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ieee80211: remove function ieee80211_{dsss_chan_to_freq, freq_to_dsss_chan}

Function ieee80211_{dsss_chan_to_freq, freq_to_dsss_chan} have been
replaced with ieee80211_{channel_to_frequency, frequency_to_channel}.

There should be no users of the two functions now. So remove them.

Cc: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Zhao, Gang <gamerh2o@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

orinoco: replace function ieee80211_{dsss_chan_to_freq, freq_to_dsss_chan}

Replace ieee80211_{dsss_chan_to_freq, freq_to_dsss_chan} with more
generic ieee80211_{channel_to_frequency, frequency_to_channel}.

File <net/cfg80211.h> has already been included. It's safe to use
IEEE80211_BAND_2GHZ here.

This change is a preparation for the removal of function
ieee80211_{dsss_chan_to_freq, freq_to_dsss_chan}.

Signed-off-by: Zhao, Gang <gamerh2o@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

zd1201: replace function ieee80211_{dsss_chan_to_freq, freq_to_dsss_chan}

Replace ieee80211_{dsss_chan_to_freq, freq_to_dsss_chan} with more
generic ieee80211_{channel_to_frequency, frequency_to_channel}.

Function ieee80211_frequency_to_channel() will return 0 if frequency
is not correctly provided, so no need to set channel to 0 explicitly.

Include <net/cfg80211.h> for the defination of IEEE80211_BAND_2GHZ.
Because <net/cfg80211.h> includes <linux/ieee80211.h>, so we can
replace <linux/ieee80211.h> with <net/cfg80211.h>.

This change is a preparation for the removal of function
ieee80211_{dsss_chan_to_freq, freq_to_dsss_chan}.

Signed-off-by: Zhao, Gang <gamerh2o@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rndis_wlan: replace function ieee80211_{dsss_chan_to_freq, freq_to_dsss_chan}

Replace ieee80211_{dsss_chan_to_freq, freq_to_dsss_chan} with more
generic ieee80211_{channel_to_frequency, frequency_to_channel}.

File <net/cfg80211.h> has already been included. It's safe to use
IEEE80211_BAND_2GHZ here.

This change is a preparation for the removal of function
ieee80211_{dsss_chan_to_freq, freq_to_dsss_chan}.

Cc: Jussi Kivilinna <jussi.kivilinna@iki.fi>
Signed-off-by: Zhao, Gang <gamerh2o@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

wl3501_cs: replace function ieee80211_{dsss_chan_to_freq, freq_to_dsss_chan}

Replace ieee80211_{dsss_chan_to_freq, freq_to_dsss_chan} with more
generic ieee80211_{channel_to_frequency, frequency_to_channel}.

Include <net/cfg80211.h> for the defination of IEEE80211_BAND_2GHZ.
Because <net/cfg80211.h> includes <linux/ieee80211.h>, so we can
replace <linux/ieee80211.h> with <net/cfg80211.h>.

This change is a preparation for the removal of function
ieee80211_{dsss_chan_to_freq, freq_to_dsss_chan}.

Cc: Arnaldo Carvalho de Melo <acme@ghostprotocols.net>
Signed-off-by: Zhao, Gang <gamerh2o@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

atmel: replace function ieee80211_{dsss_chan_to_freq, freq_to_dsss_chan}

Replace ieee80211_{dsss_chan_to_freq, freq_to_dsss_chan} with more
generic ieee80211_{channel_to_frequency, frequency_to_channel}.

Include <net/cfg80211.h> for the defination of IEEE80211_BAND_2GHZ.
Because <net/cfg80211.h> includes <linux/ieee80211.h>, so we can
replace <linux/ieee80211.h> with <net/cfg80211.h>.

This change is a preparation for the removal of function
ieee80211_{dsss_chan_to_freq, freq_to_dsss_chan}.

Cc: Simon Kelley <simon@thekelleys.org.uk>
Signed-off-by: Zhao, Gang <gamerh2o@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

airo: replace function ieee80211_{dsss_chan_to_freq, freq_to_dsss_chan}

Replace ieee80211_{dsss_chan_to_freq, freq_to_dsss_chan} with more
generic ieee80211_{channel_to_frequency, frequency_to_channel}.

Include <net/cfg80211.h> for the defination of IEEE80211_BAND_2GHZ.
Because <net/cfg80211.h> includes <linux/ieee80211.h>, so we can
replace <linux/ieee80211.h> with <net/cfg80211.h>.

This change is a preparation for the removal of function
ieee80211_{dsss_chan_to_freq, freq_to_dsss_chan}.

Signed-off-by: Zhao, Gang <gamerh2o@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rtl818x: add comments to explain few not obvious HW configs.

Certain HW options (TX packet retry count, CW configuration and
TX power configuration) can be specified in both the TX packet
descriptor and also into HW "global" registers.

The HW is thus configured to honour the global register or the
TX descriptor field depending by the case.

This patch adds few comments that hopefully clarify in which cases
the driver uses one method and in which cases it uses the other.

Signed-off-by: Andrea Merello <andrea.merello@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rtl818x: make dev_alloc_skb() null pointer check to really work

During driver initialization, some skbs are preallocated for RX.
Currenly if the allocation fails, the driver's allocation routine
exits immediatly but it will return zero (success) anyway.

In this way the driver will continue initialization with buggy
pointers around.

This patch makes the driver's allocation routine to return
an error value and to print a complaint message when skb allocation
fails.
In this way its caller will not go further, avoinding the driver to
successfully load, and preventing dereferencing buggy pointers.

An hint is thus printed about why the driver failed.

Signed-off-by: Andrea Merello <andrea.merello@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rtl818x: check for pci_map_single() success when initializing RX ring

During initialization a number of RX skbs are allocated and mapped
for DMA.
Currently if pci_map_single() fails, it will result in passing to the
HW a wrong DMA address (to write to!).

This patch adds check for this condition and eventually causes the
driver not to initialize, avoiding at least dangerous DMAs.

Signed-off-by: Andrea Merello <andrea.merello@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rtl818x: pci_iomap() should pair with pci_iounmap()

Currently the driver uses pci_iomap() but iounmap() is called in
the error path

Change to use pci_iounmap() instead.

Reported-by: Huqiu Liu <liuhq11@mails.tsinghua.edu.cn>
Signed-off-by: Andrea Merello <andrea.merello@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rtl818x: Explicitly enable contetion window

Currently the contention window enable/disable HW flag is not
touched by the driver.

This patch explicitly set it to the correct value to make sure
contention window is enabled (AFAIK contention window must be
enabled in most (if not all) cases.

Signed-off-by: Andrea Merello <andrea.merello@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Documentation: dt: wireless: Add wl1251

Add device tree binding documentation for Texas Instrument's wl1251
wireless lan chip. For now only the SPI binding is documented.

Signed-off-by: Sebastian Reichel <sre@debian.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

wl1251: spi: add device tree support

Add device tree support for the spi variant of wl1251.

Signed-off-by: Sebastian Reichel <sre@debian.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

wl1251: spi: add vio regulator support

This patch adds support for requesting the regulator powering
the vio pin.

Signed-off-by: Sebastian Reichel <sre@debian.org>
Reviewed-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

wl1251: move power GPIO handling into the driver

Move the power GPIO handling from the board code into
the driver. This is a dependency for device tree support.

Signed-off-by: Sebastian Reichel <sre@debian.org>
Reviewed-by: Pavel Machek <pavel@ucw.cz>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

wl1251: split wl251 platform data to a separate structure

Move the wl1251 part of the wl12xx platform data structure into a new
structure specifically for wl1251.  Change the platform data built-in
block and board files accordingly.

Signed-off-by: Luciano Coelho <coelho@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Reviewed-by: Sebastian Reichel <sre@debian.org>
Reviewed-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath5k: set SURVEY_INFO_IN_USE on get_survey

Only one channel is returned - the one currently being used.

Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: make some hardware reset log messages debug-only

On some chips, baseband watchdog hangs are more common than others, and
the driver has support for handling them.
Interrupts even after a watchdog hang are also quite common, so there's
not much point in spamming the user's logfiles.

Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: do not set half/quarter channel flags in AR_PHY_MODE

5/10 MHz channel bandwidth is configured via the PLL clock, instead of
the AR_PHY_MODE register. Using that register is AR93xx specific, and
makes the mode incompatible with earlier chipsets.

In some early versions, these flags were apparently applied at the wrong
point in time and thus did not cause connectivity issues, however now
they are causing problems, as pointed out in this OpenWrt ticket:

https://dev.openwrt.org/ticket/14916

Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: Use static const

Trivially reduces text size too.

$ size drivers/net/wireless/ath/ath9k/debug.o*
   text    data     bss     dec     hex filename
  34436    2528    5128   42092    a46c drivers/net/wireless/ath/ath9k/debug.o.new
  34464    2528    5128   42120    a488 drivers/net/wireless/ath/ath9k/debug.o.old

Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: list more reset causes in debugfs

Number of MAC hangs and stuck beacons were missing

Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

wireless/rt2x00: don't use PREPARE_WORK in rt2800usb.c

PREPARE_[DELAYED_]WORK() are being phased out.  They have few users
and a nasty surprise in terms of reentrancy guarantee as workqueue
considers work items to be different if they don't have the same work
function.

Update rt2800usb.c to use INIT_WORK() instead of PREPARE_WORK().  As
the work item isn't in active use during rt2800usb_probe_hw(), this
doesn't cause any behavior difference.

It would probably be best to route this with other related updates
through the workqueue tree.

Only compile tested.

Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Ivo van Doorn <IvDoorn@gmail.com>
Cc: Gertjan van Wingerde <gwingerde@gmail.com>
Cc: Helmut Schaa <helmut.schaa@googlemail.com>
Cc: linux-wireless@vger.kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>

iwlegacy: properly enable power saving

Even if we mark PS on, device still worked in normal mode. Patch
corrects that and now we send proper powertable command to device,
which put it in sleep mode when PS is on.

Reported-and-tested-by: Tino Keitel <tino.keitel@tikei.de>
Tested-by: Pedro Francisco <pedrogfrancisco@gmail.com>
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

iwlegacy: merge reclaim check

Merge reclaim check for 3945 & 4965. This add some more checks for
3945, most importantly N_RX notify.

Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

iwl3945: fix wakeup interrupt

We have only 5 tx queues on 3945, updating il->txq[5] results in
writing random value to HBUS_TARG_WRPTR register.

Additionally use spin lock to protect txq->write_ptr and
txq->need_update fields also modified in TX path.

Tested-by: Pedro Francisco <pedrogfrancisco@gmail.com>
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mwifiex: enable obss scan offload feature flag

We don't perform OBSS scan internally. As we intend to use
corresponding feature in application, we will enable this flag.

Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mwifiex: remove redundant del_timer

While modifying timer, we need not delete timer.

Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mwifiex: use del_timer_sync instead of del_timer

Use SMP safe del_timer_sync instead of del_timer for cancelling
timers.

Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: Enable U-APSD AP mode support

mac80211 handles the actual operations, so ath9k can just indicate
support for this. Based on initial tests, this combination seems to
work fine.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

drivers:net:wireless:airo.c:checkpatch.pl cleanup

removed following warnings-
drivers/net/wireless/airo.c:39: WARNING: Use #include <linux/io.h> instead of <asm/io.h>
drivers/net/wireless/airo.c:48: WARNING: Use #include <linux/uaccess.h> instead of <asm/uaccess.h>

Signed-off-by: Avinash Kumar <avi.kp.137@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

hostap: add Netgear MA401 card

This is a relatively old Prism2 card which is correctly supported
by the hostap driver.

Signed-off-by: Cédric Le Goater <clg@fr.ibm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

net: wireless: wl3501_cs: Remove duplicate include

linux/etherdevice.h was included twice.

Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

b43: return true / false instead of numbers in functions which return bool value

Signed-off-by: Zhao, Gang <gamerh2o@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

b43: Kconfig: let config B43_BCMA_PIO depends on B43

Logically, config B43_BCMA_PIO should depend on B43. This also solves
the problem that sub options of b43 driver didn't indent correctly in
make menuconfig's ncurses window.

Signed-off-by: Zhao, Gang <gamerh2o@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rtlwifi: properly apply filter flags

commit 0baa0fd76f3f5a134461d6cf30294f6bb1bb824c
("rtlwifi: Convert core routines for addition of rtl8192se and
rtl8192de") removed setting HW_VAR_RCR, HW_VAR_MGT_FILTER and
HW_VAR_CTRL_FILTER. The last two are probably done because some hardware
does not support them. The first is probably a mistake. This patch adds
the missing set_hw_reg call.

For PCI support, rx_conf is not touched directly. Instead, get_hw_reg is
used to abstract between receive_config (for PCI) and rx_conf (for USB).

This was tested on a 10ec:8176 Realtek RTL8188CE (according to the
label on the mini-PCIe card). Before this patch, `iw wlan0 set monitor
otherbss` did not capture frames from other BSS's. After this patch, it
does print packets.

Tested-by: Peter Wu <lekensteyn@gmail.com>
Signed-off-by: Peter Wu <lekensteyn@gmail.com>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rtlwifi: avoid accessing RCR directly

The rtl*_set_check_bssid functions are mostly the same, but access the
RCR register in different ways. Use the get_hw_reg abstraction layer
(which reads rtlpci->receive_config for PCI devices and mac->rx_conf for
USB).

There is no functional change for cases where receive_config was
accessed directly. For rtl8192ce, there is still no change because
nothing modifies REG_RCR or receive_config. For rtl8192cu, it now also
applies changes to rx_conf from configure_filter, but that can be
considered a bug which is fixed later.

Signed-off-by: Peter Wu <lekensteyn@gmail.com>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mwifiex: memory corruption in mwifiex_tdls_add_vht_capab()

There is a typo here because the names are confusingly similar.  The
intent was sizeof(struct ieee80211_vht_cap) (size 12) but sizeof(struct
ieee80211_ht_cap) (size 32) was used.

Anway, it's cleaner to just specify the variable instead of the type.

Fixes: 5f6d5983394f ('mwifiex: add VHT support for TDLS')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Merge branch 'for-john' of git://git./linux/kernel/git/iwlwifi/iwlwifi-next

Merge branch 'for-upstream' of git://git./linux/kernel/git/bluetooth/bluetooth-next

Merge branch 'for-john' of git://git./linux/kernel/git/jberg/mac80211-next

Merge branch 'for-linville' of git://github.com/kvalo/ath

Revert "Staging: rtl8812ae: remove modules field of rate_control_ops"

This reverts commit 35582ad9d342025653aaf28ed321bf5352488d7f.

This should not have been merged through this tree...

Signed-off-by: John W. Linville <linville@tuxdriver.com>

iwlwifi: mvm: fix a few wd_disable comments

Few minor comments.

Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

iwlwifi: mvm: prepare infrastructure for more TLV flags

We use the TLV flags as a handshake between the firmware
and the driver. These flags allow the firmware to advertise
its capabilities and API version.
Since we are running short of bits, we add a new
infrastructure which is more scalable, yet backward
compatible.

We make now the difference between API changes and the
capabilities. Both can have an index which allows to scale
at will.

Signed-off-by: Eran Harary <eran.harary@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

iwlwifi: mvm: remove redundant define in fw.c

This define is a leftover from dvm (in mvm, it
was replaced by MVM_UCODE_ALIVE_TIMEOUT).

Signed-off-by: Inbal Hacohen <Inbal.Hacohen@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

iwlwifi: nvm: remove reading valid antennas from NVM

These values aren't used as the firmware values should be used,
so reading them is pointless and hides potential errors when
somebody uses these values. Leave them zero to make it clearer
that they can't be used. We can't remove the struct members as
the DVM driver does read the values from EEPROM/OTP and the
structure is shared between drivers.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

Bluetooth: Fix iterating wrong list in hci_remove_irk()

We should be iterating hdev->identity_resolving_keys in the
hci_remove_irk() function instead of hdev->long_term_keys. This patch
fixes the issue.

Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>

mac80211: ibss: handle cfg80211_chandef_dfs_required() error codes

Error codes returned by cfg80211_chandef_dfs_required() are ignored
when trying to join an IBSS.  Fix this by printing an error and
returning.

Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

cfg80211: remove radar requirements check from cfg80211_can_use_iftype_chan()

We don't have to double check whether the parameters passed to
cfg80211_can_use_iftype_chan() are correct.  We should just make sure
they *are* when we call this function.

Remove the radar_detect argument check in
cfg80211_can_use_iftype_chan() to simplify the code.

Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
[keep braces around a long comment + single statement]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

nl80211: make sure we check for DFS with mesh channel switch

Since mesh support for DFS channels was added, we also need to check
for DFS channels when performing a channel switch with
NL80211_IFTYPE_MESHPOINT.

Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
[use switch statement, slight code cleanup]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

mac80211: allow drivers to request SMPS off

Previously we were warning and using automatic when a driver sent an
update request with SMPS off.  This patch makes it possible for
drivers to disable SMPS at runtime, for whatever reason.

Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

cfg80211: docbook: add interface combinations documentation

Add the ieee80211_iface_limit and the ieee80211_iface_combination
structures to docbook.  Reformat the examples of combinations
slightly, so it looks a bit better on docbook.

Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

cfg80211: docbook: fix small formatting error

docbook (or one of its friends) gets confused with semi-colons in the
argument descriptions, causing it to think that the semi-colon is
marking a new section in the description of addr_mask in wiphy struct.

Prevent this by using hyphens instead of semi-colons in the mask
example.

Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

cfg80211: regulatory: introduce NL80211_RRF_AUTO_BW rule flag

Introduce NL80211_RRF_AUTO_BW rule flag. If this flag set
maximum available bandwidth should be calculated base on
contiguous rules and wider channels will be allowed to cross
multiple contiguous/overlapping frequency ranges.

In case of old kernels maximum bandwidth from regulatory
rule will be used, while there is no NL80211_RRF_AUTO_BW flag.

This fixes the previous commit 9752482083066af7ac18a5ca376f
("cfg80211: regulatory introduce maximum bandwidth calculation")
which was found to be a problem for userspace API compatibility.

Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
[edit commit log, use sizeof()]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Bluetooth: Increase minor version of core module

With the addition of Resolvable Private Address (RPA) resolution
support for Bluetooth Low Energy connections, it makes sense to
increase the minor version of the Bluetooth core module.

The module version is not used anywhere, but it gives a nice extra
hint for debugging purposes.

Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>

Bluetooth: Provide option for changing LE advertising channel map

For testing purposes it is useful to provide an option to change the
advertising channel map. So add a debugfs option to allow this.

Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>

Bluetooth: Fix channel check when binding RFCOMM sock

When binding RFCOMM socket with non-zero channel we're checking if
there is already any other socket which has the same channel number
assigned and then fail. This check does not consider situation where
we have another socket connected to remote device on given channel
number in which case we still should be able to bind local socket.

This patch changes __rfcomm_get_sock_by_addr() to return only sockets
in either BT_BOUND or BT_LISTEN states, also name is updated to better
describe what this function does now.

Signed-off-by: Andrzej Kaczmarek <andrzej.kaczmarek@tieto.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

iwlwifi: mvm: add Rx frames statistics via debugfs

Collect statistics regarding rates and aggregations in Rx
frames and export the data via debugfs.

Signed-off-by: Eyal Shapira <eyalx.shapira@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

iwlwifi: mvm: set immediate apply time bit in time events

Newer firmware support a new bit in the policy  that allows
to request to apply the time event immediately. Add this bit
without removing the workarounds we used until now to support
older firmares.

Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

iwlwifi: pcie: stop the firmware when we restart it

In case the firmware didn't assert but we want to restart
it, e.g. we didn't get the reply for a host command, or the
Tx queues are stuck, we should stop the firmware by
provoking an interrupt. This allows to better debug the
firmware in these bad scenarios.

Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

iwlwifi: mvm: fix possible memory leak

iwl_parse_nvm_data() doesn't free allocated memory if it is
fed with invalid parameter. Fix this.

Signed-off-by: Eytan Lifshitz <eytan.lifshitz@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

mac80211: allow driver to return error from sched_scan_stop

In order to solve races with sched_scan_stop, it is necessary
for the driver to be able to return an error to propagate that
to cfg80211 so it doesn't send an event.

Reviewed-by: Alexander Bondar <alexander.bondar@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

cfg80211: document sched_scan_stop synchronous behaviour

Due to userspace assumptions, the sched_scan_stop operation must
be synchronous, i.e. once it returns a new scheduled scan must be
able to start immediately. Document this in the API.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>

cfg80211: Pass TDLS peer capability information in tdls_mgmt

While framing the TDLS Setup Confirmation frame, the driver needs to
know if the TDLS peer is VHT/HT/WMM capable and thus shall construct
the VHT/HT operation / WMM parameter elements accordingly. Supplicant
determines if the TDLS peer is VHT/HT/WMM capable based on the
presence of the respective IEs in the received TDLS Setup Response frame.

The host driver should not need to parse the received TDLS Response
frame and thus, should be able to rely on the supplicant to indicate
the capability of the peer through additional flags while transmitting
the TDLS Setup Confirmation frame through tdls_mgmt operations.

Signed-off-by: Sunil Dutt Undekari <usdutt@qti.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Merge remote-tracking branch 'wireless-next/master' into mac80211-next

Bluetooth: Track the current configured random address

For Bluetooth controllers with LE support, track the value of the
currently configured random address. It is important to know what
the current random address is to avoid unneeded attempts to set
a new address. This will become important when introducing the
LE privacy support in the future.

In addition expose the current configured random address via
debugfs for debugging purposes.

Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>

Bluetooth: Replace own_address_type with force_static_address debugfs

The own_address_type debugfs option does not providing enough
flexibity for interacting with the upcoming LE privacy support.

What really is needed is an option to force using the static address
compared to the public address. The new force_static_address debugfs
option does exactly that. In addition it is also only available when
the controller does actually have a public address. For single mode
LE only controllers this option will not be available.

Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>

Bluetooth: Add comment explainging store hint for long term keys

The code itself is not descriptive on what store hint is used for
long term keys and why. So add some extensive comment here. Similar
to what has already been done for identity resolving key store hint.

Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>

Bluetooth: Don't send store hint for devices using identity addresses

The identity resolving keys should only be stored for devices using
resolvable random addresses. If the device is already using an
identity address, inform it about the new identity resolving key,
but tell userspace that this key is not persistent.

Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>

Bluetooth: Add support for sending New IRK event

This patch adds the necessary helper function to send the New IRK mgmt
event and makes sure that the function is called at when SMP key
distribution has completed. The event is sent before the New LTK event
so user space knows which remote device to associate with the keys.

Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

Bluetooth: Move SMP LTK notification after key distribution

This patch moves the SMP Long Term Key notification over mgmt from the
hci_add_ltk function to smp.c when both sides have completed their key
distribution. This way we are also able to update the identity address
into the mgmt_new_ltk event.

Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

Bluetooth: Track SMP keys in the SMP context

As preparation to do mgmt notification in a single place at the end of
the key distribution, store the keys that need to be notified within the
SMP context.

Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

Bluetooth: Move New LTK store hint evaluation into mgmt_new_ltk

It's simpler (one less if-statement) to just evaluate the appropriate
value for store_hint in the mgmt_new_ltk function than to pass a boolean
parameter to the function. Furthermore, this simplifies moving the mgmt
event emission out from hci_add_ltk in subsequent patches.

Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

Bluetooth: Return added key when adding LTKs and IRKs

The SMP code will need to postpone the mgmt event emission for the IRK
and LTKs. To avoid extra lookups at the end of the key distribution
simply return the added value from the add_ltk and add_irk functions.

Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

Bluetooth: Avoid using GFP_ATOMIC where not necessary

The various pieces of data cached in the hci_dev structure do not need
to be allocated using GFP_ATOMIC since they are never added from
interrupt context. This patch updates these allocations to use
GFP_KERNEL instead.

Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

Bluetooth: Use same LE min/max connection event length during update

During LE connection establishment the value 0x0000 is used for min/max
connection event length. So use the same value when the peripheral is
requesting an update of the the connection paramters.

For some reason the value 0x0001 got used in the connection update and
0x0000 in the connection creation. Using the same value for both just
makes sense.

Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>

Bluetooth: Expose current list of identity resolving keys via debugfs

For debugging purposes expose the current list of identity resolving
keys via debugfs. This file is read-only and limited to root access.

Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>

Bluetooth: Fix wrong identity address during connection failures

When the connection attempt fails, the address information are not
provided in the HCI_LE_Connection_Complete event. So use the original
information from the connection to reconstruct the identity address.

This is important when a connection attempt has been made using the
identity address, but the cached resolvable random address has changed
in the meantime. The failure event needs to use the identity address
and not the resolvable random address.

Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>

Bluetooth: Use connection address for reporting connection failures

When reporting connect failed events to userspace, use the address
of the connection and not the address from the HCI event.

This change is strictly speaking not needed since BR/EDR does not
have the concept of resolvable random addresses. It is more for
making the code consistent.

Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>

Bluetooth: Report identity address when remote device connects

When the remote device has been successfully connected, report the
identity address (public address or static random address).

Currently the address from the HCI_LE_Connection_Complete event is
used. This was no problem so far, but since now known resolvable
random addresses are converted into identities, it is important to
use the identity of the connection and not the address report by
HCI event.

Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>

Bluetooth: Print error when dropping L2CAP data

Silently dropping L2CAP data (i.e. due to remote device not obeying
negotiated MTU) is confusing and makes debugging harder.

Signed-off-by: Szymon Janc <szymon.janc@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

Bluetooth: Use Identity Address in Device Found event

Whenever a device uses an RPA we want to have user space identify it by
its Identity Address if we've got an IRK available for it. This patch
updates the Device Found mgmt event to contain the Identity Address if
an IRK is available for the device in question.

Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

Bluetooth: Look up RPA for connection requests with Identity Address

We need to check whether there's a matching IRK and RPA when we're
requested to connect to a remote LE device based on its Identity
Address. This patch updates the hci_connect_le function to do an extra
call to hci_find_irk_by_addr and uses the RPA if it's cached. This is
particularly important once we start exposing the Identity Address to
user space instead of the RPA in events such as Device Connected and
Device Found.

Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

Bluetooth: Don't try to look up private addresses as Identity Address

Identity Addresses are either public or static random. When looking up
addresses based on the Identity Address it doesn't make sense to go
through the IRK list if we're given a private random address. This patch
fixes (or rather improves) the hci_find_irk_by_addr function to bail out
early if given a private random address.

Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

Bluetooth: Wait for SMP key distribution completion when pairing

When we initiate pairing through mgmt_pair_device the code has so far
been waiting for a successful HCI Encrypt Change event in order to
respond to the mgmt command. However, putting privacy into the play we
actually want the key distribution to be complete before replying so
that we can include the Identity Address in the mgmt response.

This patch updates the various hci_conn callbacks for LE in mgmt.c to
only respond in the case of failure, and adds a new mgmt_smp_complete
function that the SMP code will call once key distribution has been
completed.

Since the smp_chan_destroy function that's used to indicate completion
and clean up the SMP context can be called from various places,
including outside of smp.c, the easiest way to track failure vs success
is a new flag that we set once key distribution has been successfully
completed.

Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>