Jani Nikula [Tue, 4 Dec 2018 17:26:17 +0000 (19:26 +0200)]
drm/i915: Update DRIVER_DATE to
20181204
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Jani Nikula [Tue, 4 Dec 2018 10:19:26 +0000 (12:19 +0200)]
drm/i915/icl: fix transcoder state readout
Commit
2ca711caeca2 ("drm/i915/icl: Consider DSI for getting transcoder
state") clobbers the previously read TRANS_DDI_FUNC_CTL_EDP register
contents with TRANS_DDI_FUNC_CTL_DSI0 contents. Fix the state readout,
and handle DSI 1 while at it.
Use a bitmask for iterating and logging transcoders, because the allowed
combinations are a bit funky.
Fixes: 2ca711caeca2 ("drm/i915/icl: Consider DSI for getting transcoder state")
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=108928
Cc: Ville Syrjala <ville.syrjala@linux.intel.com>
Cc: Madhav Chauhan <madhav.chauhan@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181204101926.17174-1-jani.nikula@intel.com
Chris Wilson [Tue, 4 Dec 2018 14:15:16 +0000 (14:15 +0000)]
drm/i915: Allocate a common scratch page
Currently we allocate a scratch page for each engine, but since we only
ever write into it for post-sync operations, it is not exposed to
userspace nor do we care for coherency. As we then do not care about its
contents, we can use one page for all, reducing our allocations and
avoid complications by not assuming per-engine isolation.
For later use, it simplifies engine initialisation (by removing the
allocation that required struct_mutex!) and means that we can always rely
on there being a scratch page.
v2: Check that we allocated a large enough scratch for I830 w/a
Fixes: 06e562e7f515 ("drm/i915/ringbuffer: Delay after EMIT_INVALIDATE for gen4/gen5") # v4.18.20
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=108850
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181204141522.13640-1-chris@chris-wilson.co.uk
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: <stable@vger.kernel.org> # v4.18.20+
Tvrtko Ursulin [Mon, 3 Dec 2018 12:50:14 +0000 (12:50 +0000)]
drm/i915: Trim unused workaround list entries
The new workaround list allocator grows the list in chunks so will end up
with some unused space. Trim it when the initialization phase is done to
free up a tiny bit of slab.
v2:
* Simplify with kmemdup. (Chris Wilson)
v3:
* Refactor for __size removal.
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20181203125014.3219-8-tvrtko.ursulin@linux.intel.com
Tvrtko Ursulin [Mon, 3 Dec 2018 13:33:57 +0000 (13:33 +0000)]
drm/i915: Fuse per-context workaround handling with the common framework
Convert the per context workaround handling code to run against the newly
introduced common workaround framework and fuse the two to use the
existing smarter list add helper, the one which does the sorted insert and
merges registers where possible.
This completes migration of all four classes of workarounds onto the
common framework.
Existing macros are kept untouched for smaller code churn.
v2:
* Rename to list name ctx_wa_list and move from dev_priv to engine.
v3:
* API rename and parameters tweaking. (Chris Wilson)
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20181203133357.10341-1-tvrtko.ursulin@linux.intel.com
Tvrtko Ursulin [Mon, 3 Dec 2018 12:50:12 +0000 (12:50 +0000)]
drm/i915: Move register white-listing to the common workaround framework
Instead of having a separate list of white-listed registers we can
trivially move this to the common workarounds framework.
This brings us one step closer to the goal of driving all workaround
classes using the same code.
v2:
* Use GEM_DEBUG_WARN_ON for the sanity check. (Chris Wilson)
v3:
* API rename. (Chris Wilson)
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20181203125014.3219-6-tvrtko.ursulin@linux.intel.com
Tvrtko Ursulin [Mon, 3 Dec 2018 12:50:11 +0000 (12:50 +0000)]
drm/i915/selftests: Add tests for GT and engine workaround verification
Two simple selftests which test that both GT and engine workarounds are
not lost after either a full GPU reset, or after the per-engine ones.
(Including checks that one engine reset is not affecting workarounds not
belonging to itself.)
v2:
* Rebase for series refactoring.
* Add spinner for actual engine reset!
* Add idle reset test as well. (Chris Wilson)
* Share existing global_reset_lock. (Chris Wilson)
v3:
* intel_engine_verify_workarounds can be static.
* API rename. (Chris Wilson)
* Move global reset lock out of the loop. (Chris Wilson)
v4:
* Add missing rpm puts. (Chris Wilson)
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20181203125014.3219-5-tvrtko.ursulin@linux.intel.com
Tvrtko Ursulin [Mon, 3 Dec 2018 12:50:10 +0000 (12:50 +0000)]
drm/i915: Verify GT workaround state after GPU init
Since we now have all the GT workarounds in a table, by adding a simple
shared helper function we can now verify that their values are still
applied after some interesting events in the lifetime of the driver.
Initially we only do this after GPU initialization.
v2:
Chris Wilson:
* Simplify verification by realizing it's a simple xor and and.
* Remove verification from engine reset path.
* Return bool straight away from the verify API.
v3:
* API rename. (Chris Wilson)
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20181203125014.3219-4-tvrtko.ursulin@linux.intel.com
Tvrtko Ursulin [Mon, 3 Dec 2018 13:33:41 +0000 (13:33 +0000)]
drm/i915: Introduce per-engine workarounds
We stopped re-applying the GT workarounds after engine reset since commit
59b449d5c82a ("drm/i915: Split out functions for different kinds of
workarounds").
Issue with this is that some of the GT workarounds live in the MMIO space
which gets lost during engine resets. So far the registers in 0x2xxx and
0xbxxx address range have been identified to be affected.
This losing of applied workarounds has obvious negative effects and can
even lead to hard system hangs (see the linked Bugzilla).
Rather than just restoring this re-application, because we have also
observed that it is not safe to just re-write all GT workarounds after
engine resets (GPU might be live and weird hardware states can happen),
we introduce a new class of per-engine workarounds and move only the
affected GT workarounds over.
Using the framework introduced in the previous patch, we therefore after
engine reset, re-apply only the workarounds living in the affected MMIO
address ranges.
v2:
* Move Wa_1406609255:icl to engine workarounds as well.
* Rename API. (Chris Wilson)
* Drop redundant IS_KABYLAKE. (Chris Wilson)
* Re-order engine wa/ init so latest platforms are first. (Rodrigo Vivi)
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Bugzilla: https://bugzilla.freedesktop.org/show_bug.cgi?id=107945
Fixes: 59b449d5c82a ("drm/i915: Split out functions for different kinds of workarounds")
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: intel-gfx@lists.freedesktop.org
Acked-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20181203133341.10258-1-tvrtko.ursulin@linux.intel.com
Tvrtko Ursulin [Mon, 3 Dec 2018 13:33:19 +0000 (13:33 +0000)]
drm/i915: Record GT workarounds in a list
To enable later verification of GT workaround state at various stages of
driver lifetime, we record the list of applicable ones per platforms to a
list, from which they are also applied.
The added data structure is a simple array of register, mask and value
items, which is allocated on demand as workarounds are added to the list.
This is a temporary implementation which later in the series gets fused
with the existing per context workaround list handling. It is separated at
this stage since the following patch fixes a bug which needs to be as easy
to backport as possible.
Also, since in the following patch we will be adding a new class of
workarounds (per engine) which can be applied from interrupt context, we
straight away make the provision for safe read-modify-write cycle.
v2:
* Change dev_priv to i915 along the init path. (Chris Wilson)
* API rename. (Chris Wilson)
v3:
* Remove explicit list size tracking in favour of growing the allocation
in power of two chunks. (Chris Wilson)
v4:
Chris Wilson:
* Change wa_list_finish to early return.
* Copy workarounds using the compiler for static checking.
* Do not bother zeroing unused entries.
* Re-order struct i915_wa_list.
v5:
* kmalloc_array.
* Whitespace cleanup.
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20181203133319.10174-1-tvrtko.ursulin@linux.intel.com
Jonathan Gray [Thu, 29 Nov 2018 01:30:51 +0000 (12:30 +1100)]
drm/i915: change i915_sw_fence license to MIT
Change the license of the i915_sw_fence files to MIT matching
most of the other i915 files. This makes it possible to use them
in a new port of i915 to OpenBSD.
Besides some mechanical tree wide changes Chris Wilson is the sole
author of these files with Intel holding the copyright.
Intel's legal team have given permission to change the license according
to Joonas Lahtinen.
v2: expand commit message and note permission from Intel legal
Signed-off-by: Jonathan Gray <jsg@jsg.id.au>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20181129013051.17525-1-jsg@jsg.id.au
Chris Wilson [Mon, 3 Dec 2018 11:36:55 +0000 (11:36 +0000)]
drm/i915: Complete the fences as they are cancelled due to wedging
We inspect the requests under the assumption that they will be marked as
completed when they are removed from the queue. Currently however, in the
process of wedging the requests will be removed from the queue before they
are completed, so rearrange the code to complete the fences before the
locks are dropped.
<1>[ 354.473346] BUG: unable to handle kernel NULL pointer dereference at
0000000000000250
<6>[ 354.473363] PGD 0 P4D 0
<4>[ 354.473370] Oops: 0000 [#1] PREEMPT SMP PTI
<4>[ 354.473380] CPU: 0 PID: 4470 Comm: gem_eio Tainted: G U 4.20.0-rc4-CI-CI_DRM_5216+ #1
<4>[ 354.473393] Hardware name: Intel Corporation NUC7CJYH/NUC7JYB, BIOS JYGLKCPX.86A.0027.2018.0125.1347 01/25/2018
<4>[ 354.473480] RIP: 0010:__i915_schedule+0x311/0x5e0 [i915]
<4>[ 354.473490] Code: 49 89 44 24 20 4d 89 4c 24 28 4d 89 29 44 39 b3 a0 04 00 00 7d 3a 41 8b 44 24 78 85 c0 74 13 48 8b 93 78 04 00 00 48 83 e2 fc <39> 82 50 02 00 00 79 1e 44 89 b3 a0 04 00 00 48 8d bb d0 03 00 00
<4>[ 354.473515] RSP: 0018:
ffffc900001bba90 EFLAGS:
00010046
<4>[ 354.473524] RAX:
0000000000000003 RBX:
ffff8882624c8008 RCX:
f34a737800000000
<4>[ 354.473535] RDX:
0000000000000000 RSI:
0000000000000000 RDI:
ffff8882624c8048
<4>[ 354.473545] RBP:
ffffc900001bbab0 R08:
000000005963f1f1 R09:
0000000000000000
<4>[ 354.473556] R10:
ffffc900001bba10 R11:
ffff8882624c8060 R12:
ffff88824fdd7b98
<4>[ 354.473567] R13:
ffff88824fdd7bb8 R14:
0000000000000001 R15:
ffff88824fdd7750
<4>[ 354.473578] FS:
00007f44b4b5b980(0000) GS:
ffff888277e00000(0000) knlGS:
0000000000000000
<4>[ 354.473590] CS: 0010 DS: 0000 ES: 0000 CR0:
0000000080050033
<4>[ 354.473599] CR2:
0000000000000250 CR3:
000000026976e000 CR4:
0000000000340ef0
<4>[ 354.473611] Call Trace:
<4>[ 354.473622] ? lock_acquire+0xa6/0x1c0
<4>[ 354.473677] ? i915_schedule_bump_priority+0x57/0xd0 [i915]
<4>[ 354.473736] i915_schedule_bump_priority+0x72/0xd0 [i915]
<4>[ 354.473792] i915_request_wait+0x4db/0x840 [i915]
<4>[ 354.473804] ? get_pwq.isra.4+0x2c/0x50
<4>[ 354.473813] ? ___preempt_schedule+0x16/0x18
<4>[ 354.473824] ? wake_up_q+0x70/0x70
<4>[ 354.473831] ? wake_up_q+0x70/0x70
<4>[ 354.473882] ? gen6_rps_boost+0x118/0x120 [i915]
<4>[ 354.473936] i915_gem_object_wait_fence+0x8a/0x110 [i915]
<4>[ 354.473991] i915_gem_object_wait+0x113/0x500 [i915]
<4>[ 354.474047] i915_gem_wait_ioctl+0x11c/0x2f0 [i915]
<4>[ 354.474101] ? i915_gem_unset_wedged+0x210/0x210 [i915]
<4>[ 354.474113] drm_ioctl_kernel+0x81/0xf0
<4>[ 354.474123] drm_ioctl+0x2de/0x390
<4>[ 354.474175] ? i915_gem_unset_wedged+0x210/0x210 [i915]
<4>[ 354.474187] ? finish_task_switch+0x95/0x260
<4>[ 354.474197] ? lock_acquire+0xa6/0x1c0
<4>[ 354.474207] do_vfs_ioctl+0xa0/0x6e0
<4>[ 354.474217] ? __fget+0xfc/0x1e0
<4>[ 354.474225] ksys_ioctl+0x35/0x60
<4>[ 354.474233] __x64_sys_ioctl+0x11/0x20
<4>[ 354.474241] do_syscall_64+0x55/0x190
<4>[ 354.474251] entry_SYSCALL_64_after_hwframe+0x49/0xbe
<4>[ 354.474260] RIP: 0033:0x7f44b3de65d7
<4>[ 354.474267] Code: b3 66 90 48 8b 05 b1 48 2d 00 64 c7 00 26 00 00 00 48 c7 c0 ff ff ff ff c3 66 2e 0f 1f 84 00 00 00 00 00 b8 10 00 00 00 0f 05 <48> 3d 01 f0 ff ff 73 01 c3 48 8b 0d 81 48 2d 00 f7 d8 64 89 01 48
<4>[ 354.474293] RSP: 002b:
00007fff974948e8 EFLAGS:
00000246 ORIG_RAX:
0000000000000010
<4>[ 354.474305] RAX:
ffffffffffffffda RBX:
0000000000000000 RCX:
00007f44b3de65d7
<4>[ 354.474316] RDX:
00007fff97494940 RSI:
00000000c010646c RDI:
0000000000000007
<4>[ 354.474327] RBP:
00007fff97494940 R08:
0000000000000000 R09:
00007f44b40bbc40
<4>[ 354.474337] R10:
0000000000000000 R11:
0000000000000246 R12:
00000000c010646c
<4>[ 354.474348] R13:
0000000000000007 R14:
0000000000000000 R15:
0000000000000000
v2: Avoid floating requests.
v3: Can't call dma_fence_signal() under the timeline lock!
v4: Can't call dma_fence_signal() from inside another fence either.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181203113701.12106-2-chris@chris-wilson.co.uk
Chris Wilson [Tue, 20 Nov 2018 20:24:39 +0000 (20:24 +0000)]
drm/i915/dp: Fix inconsistent indenting
Always show the FEC capability as it is initialised to 0 before error.
Fixing,
drivers/gpu/drm/i915/intel_dp.c:3846 intel_dp_get_dsc_sink_cap() warn: inconsistent indenting
Fixes: 08cadae8e157 ("i915/dp/fec: Cache the FEC_CAPABLE DPCD register")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Ville Syrjala <ville.syrjala@linux.intel.com>
Cc: Manasi Navare <manasi.d.navare@intel.com>
Cc: Anusha Srivatsa <anusha.srivatsa@intel.com>
Reviewed-by: Anusha Srivatsa <anusha.srivatsa@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181120202439.13017-2-chris@chris-wilson.co.uk
José Roberto de Souza [Fri, 30 Nov 2018 23:20:48 +0000 (15:20 -0800)]
drm/i915: Move display device info capabilities to its own struct
This helps separate what capabilities are display capabilities.
v3: Moving display struct right after flags (Lucas)
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Suggested-by: Jani Nikula <jani.nikula@linux.intel.com>
Suggested-by: Lucas De Marchi <lucas.demarchi@intel.com>
Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181130232048.14216-2-jose.souza@intel.com
José Roberto de Souza [Fri, 30 Nov 2018 23:20:47 +0000 (15:20 -0800)]
drm/i915: Add HAS_DISPLAY() and use it
Right now it is decided if GEN has display by checking the num_pipes,
so lets make it explicit and use a macro.
Cc: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181130232048.14216-1-jose.souza@intel.com
Manasi Navare [Sat, 1 Dec 2018 01:04:12 +0000 (17:04 -0800)]
drm/i915/dp: Fix link compute m_n calc for DSC
Fix the intel_link_compute_m_n in case of display stream
compression. This patch passes the compressed_bpp to
intel_link_compute_m_n if compression is enabled.
Fixes: a4a157777c80 ("drm/i915/dp: Compute DSC pipe config in atomic check")
Cc: Ville Syrjala <ville.syrjala@linux.intel.com>
Cc: Anusha Srivatsa <anusha.srivatsa@intel.com>
Signed-off-by: Manasi Navare <manasi.d.navare@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181201010412.32372-1-manasi.d.navare@intel.com
Jani Nikula [Thu, 4 Oct 2018 14:37:50 +0000 (17:37 +0300)]
drm/i915/sysfs: make attrs arrays const
They don't need to be modified.
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: "Rafael J. Wysocki" <rafael@kernel.org>
Reviewed-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181004143750.30880-2-jani.nikula@intel.com
Jani Nikula [Thu, 4 Oct 2018 14:37:49 +0000 (17:37 +0300)]
sysfs: constify sysfs create/remove files harder
Let the passed in array be const (and thus placed in rodata) instead of
a mutable array of const pointers.
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: "Rafael J. Wysocki" <rafael@kernel.org>
Reviewed-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181004143750.30880-1-jani.nikula@intel.com
Chris Wilson [Fri, 30 Nov 2018 12:59:54 +0000 (12:59 +0000)]
drm/i915/vgpu: Disallow loading on old vGPU hosts
Since commit
fd8526e50902 ("drm/i915/execlists: Trust the CSB") we
actually broke the force-mmio mode for our execlists implementation. No
one noticed, so ergo no one is actually using an old vGPU host (where we
required the older method) and so can simply remove the broken support.
v2: csb_read can go as well (Mika)
Reported-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Fixes: fd8526e50902 ("drm/i915/execlists: Trust the CSB")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Cc: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181130125954.11924-1-chris@chris-wilson.co.uk
Chris Wilson [Mon, 3 Dec 2018 11:36:54 +0000 (11:36 +0000)]
drm/i915/breadcrumbs: Reduce missed-breadcrumb false positive rate
Change the on-cpu check to on-runqueue to catch if the waiter has been
woken (and reset its current_state back to TASK_UNINTERRUPTIBLE to
perform the seqno check) but is sleeping due to being preempted off the
cpu.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181203113701.12106-1-chris@chris-wilson.co.uk
Jani Nikula [Mon, 3 Dec 2018 09:43:26 +0000 (11:43 +0200)]
drm/i915/icl: add pll mapping for DSI
Add encoder specific pll mapping for DSI. The differences with the DDI
version are big enough to warrant a separate function.
v2: add posting read (Madhav)
Cc: Madhav Chauhan <madhav.chauhan@intel.com>
Cc: Vandita Kulkarni <vandita.kulkarni@intel.com>
Reviewed-by: Madhav Chauhan <madhav.chauhan@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181203094326.28294-1-jani.nikula@intel.com
Madhav Chauhan [Thu, 29 Nov 2018 14:12:34 +0000 (16:12 +0200)]
drm/i915/icl: Ungate DSI clocks
Ungate the clocks on the selected port.
Signed-off-by: Madhav Chauhan <madhav.chauhan@intel.com>
Signed-off-by: Vandita Kulkarni <vandita.kulkarni@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/2a01b3158feda624f98581b780854fe3df8c328d.1543500286.git.jani.nikula@intel.com
Madhav Chauhan [Thu, 29 Nov 2018 14:12:33 +0000 (16:12 +0200)]
drm/i915/icl: Gate clocks for DSI
As per BSPEC, depending on the DSI transcoder being used,
DDI clock for the associated port should be gated. This
patch does the same.
Signed-off-by: Madhav Chauhan <madhav.chauhan@intel.com>
Signed-off-by: Vandita Kulkarni <vandita.kulkarni@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/e032bc3d8fff91b8c2631c73121268214615a7e8.1543500286.git.jani.nikula@intel.com
Jani Nikula [Thu, 29 Nov 2018 14:12:32 +0000 (16:12 +0200)]
drm/i915/icl: add dummy DSI GPIO element execution function
Add dummy debug logging GPIO element execution function for ICL.
Reviewed-by: Madhav Chauhan <madhav.chauhan@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/f59009ea0a0ebc489a5ec66f387d9dcf7264141f.1543500286.git.jani.nikula@intel.com
Madhav Chauhan [Thu, 29 Nov 2018 14:12:31 +0000 (16:12 +0200)]
drm/i915/icl: Define display GPIO pins for DSI
Display Pins are the only GPIOs that need to be used by
driver for DSI panels. So driver should now have its own
implementation to toggle these pins based on GPIO info
received from VBT sequences.
Signed-off-by: Madhav Chauhan <madhav.chauhan@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/e7e3bb05d4f48b1876169a69f495bcf6d511fda5.1543500286.git.jani.nikula@intel.com
Madhav Chauhan [Thu, 29 Nov 2018 14:12:30 +0000 (16:12 +0200)]
drm/i915/icl: Define Panel power ctrl register
There are two panel power sequencers. Each register
has two addressable instances. This patch defines
both the instances of Panel power control register
Signed-off-by: Madhav Chauhan <madhav.chauhan@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/99bb687b17a9165527a6210a79271c8175c8a4e3.1543500286.git.jani.nikula@intel.com
Madhav Chauhan [Thu, 29 Nov 2018 14:12:29 +0000 (16:12 +0200)]
drm/i915/icl: Define missing bitfield for shortplug reg
This patch define missing bitfield for shortplug ctl ddi
register which will be used for ICL DSI GPIO programming.
Signed-off-by: Madhav Chauhan <madhav.chauhan@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/4b9feb75eb6c303556b91c8a23c505a4593a99a1.1543500286.git.jani.nikula@intel.com
Madhav Chauhan [Thu, 29 Nov 2018 14:12:28 +0000 (16:12 +0200)]
drm/i915/icl: Get pipe timings for DSI
Transcoder timings for Gen11 DSI encoder
is available at pipe level unlike in older platform
where port specific registers need to be accessed.
v2 by Jani:
- get timings for (!dsi || icl) instead of (dsi && icl).
Signed-off-by: Madhav Chauhan <madhav.chauhan@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/f60e0c1aee08248e758da3219d3239898b43ba41.1543500286.git.jani.nikula@intel.com
Madhav Chauhan [Thu, 29 Nov 2018 14:12:27 +0000 (16:12 +0200)]
drm/i915/icl: Consider DSI for getting transcoder state
For Gen11 DSI, we use similar registers like for eDP
to find if DSI encoder is connected or not to a pipe.
This patch refactors existing hsw_get_transcoder_state()
to handle this.
v2 by Jani:
- Add WARN_ON(dsi && edp) (Ville)
Signed-off-by: Madhav Chauhan <madhav.chauhan@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/2e10b977dfc7aa985a8559d6cd59ed0981848e95.1543500286.git.jani.nikula@intel.com
Madhav Chauhan [Thu, 29 Nov 2018 14:12:26 +0000 (16:12 +0200)]
drm/i915/icl: Configure DSI Dual link mode
This patch configures DSI video mode dual link by
programming DSS_CTL registers.
v2: Use new bitfield definitions from Anusha's patch
Correct register to be programmed and use max
depth buffer value (James)
v3 by Jani:
- checkpatch fixes
Signed-off-by: Madhav Chauhan <madhav.chauhan@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/d8962f4e1beffc2099b8bef8cb5a5191aa1d9efd.1543500286.git.jani.nikula@intel.com
Madhav Chauhan [Thu, 29 Nov 2018 14:12:25 +0000 (16:12 +0200)]
drm/i915/icl: Add DSI encoder compute config hook
This patch implements compute config for Gen11 DSI encoder which is
required at the time of modeset.
For DSI 8X clock is AFE clock which is 5 times port clock.
v2 by Jani:
- drop the enable nop hook
- fixed_mode is always true
- HAS_GMCH_DISPLAY() is always false
v3 by Jani:
- set encoder->compute_config dropped during rebase
v4 by Jani:
- squash Vandita's port clock patch
- remove todo comment
Co-developed-by: Vandita Kulkarni <vandita.kulkarni@intel.com>
Signed-off-by: Madhav Chauhan <madhav.chauhan@intel.com>
Signed-off-by: Vandita Kulkarni <vandita.kulkarni@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/a21574173caa5e2932d9e3c537b0931097ab5ac2.1543500286.git.jani.nikula@intel.com
Madhav Chauhan [Thu, 29 Nov 2018 14:12:24 +0000 (16:12 +0200)]
drm/i915/icl: Get HW state for DSI encoder
This patch read out the current hw state for DSI and
return true if encoder is active.
v2 by Jani:
- Squash connector get hw state hook here
- Squash encode get hw state fix here
v3 by Jani:
- Add encoder->get_power_domains() (Imre)
v4 by Jani:
- Make encoder->get_power_domains() sensible... (Imre)
v5 by Jani:
- Power domains are bit positions, not bits (Stan, Imre)
Cc: Imre Deak <imre.deak@intel.com>
Signed-off-by: Madhav Chauhan <madhav.chauhan@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/ec6da32a55b9fb045527f14e41ed3dce86d46a97.1543500286.git.jani.nikula@intel.com
Vandita Kulkarni [Thu, 29 Nov 2018 14:12:23 +0000 (16:12 +0200)]
drm/i915/icl: Add get config functionality for DSI
This patch implements the functionality for getting PIPE configuration
to which DSI encoder is connected. Use the same method to get port clock
like other DDI encoders. Used during the atomic modeset.
v2 by Jani:
- Squash Madhav's and Vandita's get config bits together
- Move cnl_calc_wrpll_link() to intel_drv.h
- Drop extra temp variables
- Use enc_to_intel_dsi() instead of open coding
Co-developed-by: Madhav Chauhan <madhav.chauhan@intel.com>
Signed-off-by: Vandita Kulkarni <vandita.kulkarni@intel.com>
Signed-off-by: Madhav Chauhan <madhav.chauhan@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/f21fa4258068d04582f2bf30735e5536a8043bdf.1543500286.git.jani.nikula@intel.com
Madhav Chauhan [Thu, 29 Nov 2018 14:12:22 +0000 (16:12 +0200)]
drm/i915/icl: Allocate DSI hosts and imlement host transfer
Allocate DSI host structure for each DSI port available on gen11 and
register them with DSI fwk of DRM. Some of the DSI host operations are
also registered as part of this.
Retrieves DSI pkt (from DSI msg) to be sent over DSI link using DRM DSI
exported functions. A wrapper function is also added as "DSI host
transfer" for sending DSI data/cmd. Add DSI packet payload to command
payload queue using credit based mechanism for *long* packets.
v2 by Jani:
- indentation
- Use the new credit available helper
- Use int for free_credits
- Add intel_dsi local variable for better code flow
- Use the new credit available helper
- Use int for free_credits, i, and j
v3 by Jani:
- Squash DSI host allocation and transfer patches together
Signed-off-by: Madhav Chauhan <madhav.chauhan@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/af4f168ed8737d44687d8b6f21ecaa7e805eb695.1543500286.git.jani.nikula@intel.com
Madhav Chauhan [Thu, 29 Nov 2018 14:12:21 +0000 (16:12 +0200)]
drm/i915/icl: Fill DSI ports info
This patch fills backlight, CABC and general port
info for Gen11 DSI.
Signed-off-by: Madhav Chauhan <madhav.chauhan@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/48c9f867d61a60dc7c2ce744ac2325655652c55f.1543500286.git.jani.nikula@intel.com
Vandita Kulkarni [Thu, 29 Nov 2018 14:12:20 +0000 (16:12 +0200)]
drm/i915/icl: Use the same pll functions for dsi
The same pll manager functions can be used to enable dpll for
mipi. Hence enabling the IO power and esc clock as part of pre pll
enable call.
v2 by Jani:
- fix function parameter indent (Madhav)
Signed-off-by: Vandita Kulkarni <vandita.kulkarni@intel.com>
Reviewed-by: Madhav Chauhan <madhav.chauhan@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/07db5b1ce59c00295fad8a8e81908d59d8d76915.1543500286.git.jani.nikula@intel.com
Madhav Chauhan [Thu, 29 Nov 2018 14:12:19 +0000 (16:12 +0200)]
drm/i915/icl: Allocate DSI encoder/connector
This patch allocates memory for DSI encoder and connector
which will be used for various DSI encoder/connector operations
and attaching the same to DRM subsystem. This patch also extracts
DSI modes info from VBT and save the desired mode info to connector.
v2 by Jani:
- Drop GEN11 prefix from encoder name
- Drop extra parenthesis
- Drop extra local variable
- Squash encoder power domain here
v3 by Jani:
- Squash connector and connector helper functions here
- Move intel_dsi_vbt_init call here
Signed-off-by: Madhav Chauhan <madhav.chauhan@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/0197023b92ffa2d59064e30fd4ca22b6a4cff16c.1543500286.git.jani.nikula@intel.com
Madhav Chauhan [Thu, 29 Nov 2018 14:12:18 +0000 (16:12 +0200)]
drm/i915/icl: Calculate DPLL params for DSI
This patch calculates various DPLL dividers and
parameters for DSI encoder and adjust AFE clock
for DSI. For DSI, 8x clock is AFE clock.
v2: Extend haswell_crtc_compute_clock() for Gen11 DSI
v3: Rebase
v4: use port clock instead of bitrate.
v5: Reabse and remove divide by 5
v6 by Jani:
- Fix indent (Madhav)
- Fix dpll state calc for EDP and DP MST
Co-developed-by: Vandita Kulkarni <vandita.kulkarni@intel.com>
Signed-off-by: Madhav Chauhan <madhav.chauhan@intel.com>
Signed-off-by: Vandita Kulkarni <vandita.kulkarni@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/525d41d0d893dcdc8874d2ce70afa226227ea3f4.1543500285.git.jani.nikula@intel.com
Imre Deak [Thu, 29 Nov 2018 14:12:17 +0000 (16:12 +0200)]
drm/i915/icl: Sanitize DDI port clock gating for DSI ports
The requirement for the DDI port clock gating for a port in DSI mode is
the opposite wrt. the case when the port is in DDI mode: the clock
should be gated when the port is active and ungated when the port is
inactive. Note that we cannot simply keep the DDI clock gated when the
port will be only used in DSI mode: it must be gated/ungated at a
specific spot in the DSI enable/disable sequence.
Ensure the above for all ports of a DSI encoder, also adding a sanity
check that we haven't registered another encoder using the same port
(VBT should never allow this to happen).
Cc: Madhav Chauhan <madhav.chauhan@intel.com>
Cc: Vandita Kulkarni <vandita.kulkarni@intel.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Clint Taylor <clinton.a.taylor@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/ceb14d5a68e8e23988d923d4290a4f981789e616.1543500285.git.jani.nikula@intel.com
Jani Nikula [Thu, 29 Nov 2018 14:12:16 +0000 (16:12 +0200)]
drm/i915/icl: push pll to port mapping/unmapping to ddi encoder hooks
Unclutter the haswell_crtc_enable() and haswell_crtc_disable() functions
a bit by moving the pll to port mapping and unmapping functions to the
ddi encoder hooks. This allows removal of a bunch of boilerplate code
from the functions.
Additionally, the ICL DSI encoder needs to do the clock gating and
ungating slightly differently, and this allows its own handling in a
clean fashion.
Cc: Madhav Chauhan <madhav.chauhan@intel.com>
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Madhav Chauhan <madhav.chauhan@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/f8e2982ceea4c05dc254a0c15e2b3be1d5f271d3.1543500285.git.jani.nikula@intel.com
Chris Wilson [Mon, 3 Dec 2018 11:36:59 +0000 (11:36 +0000)]
drm/i915/selftests: Terminate hangcheck sanitycheck forcibly
If all else fails and we are stuck eternally waiting for the undying
request, abandon all hope.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181203113701.12106-6-chris@chris-wilson.co.uk
Chris Wilson [Mon, 3 Dec 2018 11:36:56 +0000 (11:36 +0000)]
drm/i915/ringbuffer: Clear semaphore sync registers on ring init
Ensure that the sync registers are cleared every time we restart the
ring to avoid stale values from creeping in from random neutrinos.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=108888
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181203113701.12106-3-chris@chris-wilson.co.uk
José Roberto de Souza [Wed, 28 Nov 2018 07:28:38 +0000 (23:28 -0800)]
drm/i915/psr: Get pipe id following atomic guidelines
As stated in struct drm_encoder, crtc field should only be used
by non-atomic drivers.
So here caching the pipe id in intel_psr_enable() what is way more
simple and efficient than at every call to
intel_psr_flush()/invalidate() get the
drm.mode_config.connection_mutex lock to safely be able to get the
pipe id by reading drm_connector_state.crtc.
This should fix the null pointer dereference crash below as the
previous way to get the pipe id was prone to race conditions.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=105959
Cc: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181128072838.22773-1-jose.souza@intel.com
Tvrtko Ursulin [Fri, 30 Nov 2018 09:52:11 +0000 (09:52 +0000)]
drm/i915/selftests: Fix live_workarounds to actually do resets
The test was missing some magic ingredients to actually trigger the
resets.
In case of the full reset we need the I915_RESET_HANDOFF flag set, and in
case of engine reset we need a busy request.
Thanks to Chris for helping with reset magic.
v2:
* Grab RPM ref over reset.
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20181130095211.23849-1-tvrtko.ursulin@linux.intel.com
Tvrtko Ursulin [Fri, 30 Nov 2018 08:02:53 +0000 (08:02 +0000)]
drm/i915/selftests: Extract spinner code
Pull out spinner code to a standalone file to enable it to be shortly used
by other and new test cases.
Plain code movement - no functional changes.
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20181130080254.15383-1-tvrtko.ursulin@linux.intel.com
Tvrtko Ursulin [Thu, 29 Nov 2018 13:46:30 +0000 (13:46 +0000)]
drm/i915/icl: Remove Wa_1604302699
It seems that the documentation does not reference this any more, plus,
bit 28 does not stick when written to the register.
Therefore I can only assume this is something which was documented in the
past but got removed from the hardware in the meantime.
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181129134630.8222-1-tvrtko.ursulin@linux.intel.com
Tvrtko Ursulin [Thu, 29 Nov 2018 13:41:28 +0000 (13:41 +0000)]
drm/i915: Remove whitelist application from ringbuffer backend
There is no white-listing before Gen8 and after the removal ringbuffer
support for these platforms we can remove the call to this no-op.
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20181129134128.7994-1-tvrtko.ursulin@linux.intel.com
Chris Wilson [Thu, 29 Nov 2018 21:05:43 +0000 (21:05 +0000)]
drm/i915: Fixup stub definitions for intel_opregion_suspend|resume
248 "multiple definition of ...". E.g.:
LD [M] drivers/gpu/drm/i915/i915.o
ld: drivers/gpu/drm/i915/i915_irq.o: in function `intel_opregion_resume':
i915_irq.c:(.text+0x58f0): multiple definition of `intel_opregion_resume';
drivers/gpu/drm/i915/i915_drv.o:i915_drv.c:(.text+0x2d40): first defined here
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Fixes: a950adc6c343 ("drm/i915: Stop calling intel_opregion unregister/register in suspend/resume")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Acked-by: Randy Dunlap <rdunlap@infradead.org> # build tested
Link: https://patchwork.freedesktop.org/patch/msgid/20181129210543.31555-1-chris@chris-wilson.co.uk
Anusha Srivatsa [Wed, 28 Nov 2018 20:26:28 +0000 (12:26 -0800)]
drm/i915/fec: Disable FEC state.
Set the suitable bits in DP_TP_CTL to stop
bit correction when DSC is disabled.
v2:
- rebased.
- Add additional check for compression state. (Gaurav)
v3: rebased.
v4:
- Move the code to the proper spot according to spec (Ville)
- Use proper checks (manasi)
v5: Remove unnecessary checks (Ville)
v6: Resolve warnings. Add crtc_state as an argument to
intel_disable_ddi_buf(). (Manasi)
Cc: dri-devel@lists.freedesktop.org
Cc: Gaurav K Singh <gaurav.k.singh@intel.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Ville Syrjala <ville.syrjala@linux.intel.com>
Cc: Manasi Navare <manasi.d.navare@intel.com>
Signed-off-by: Anusha Srivatsa <anusha.srivatsa@intel.com>
Signed-off-by: Manasi Navare <manasi.d.navare@intel.com>
Reviewed-by: Manasi Navare <manasi.d.navare@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181128202628.20238-17-manasi.d.navare@intel.com
Anusha Srivatsa [Wed, 28 Nov 2018 20:26:27 +0000 (12:26 -0800)]
i915/dp/fec: Configure the Forward Error Correction bits.
If FEC is supported, the corresponding
DP_TP_CTL register bits have to be configured.
The driver has to program the FEC_ENABLE in DP_TP_CTL[30] register
and wait till FEC_STATUS in DP_TP_CTL[28] is 1.
Also add the warn message to make sure that the control
register is already active while enabling FEC.
v2:
- Change commit message. Configure fec state after
link training (Manasi, Gaurav)
- Remove redundent checks (Manasi)
- Remove the registers that get added automagically (Anusha)
v3: s/intel_dp_set_fec_state()/intel_dp_enable_fec_state() (Gaurav)
v4: rebased.
v5:
- Move the code to the proper spot, according to spec.(Ville)
- Use fec state as a check too.
v6: Pass intel_encoder, instead of intel_dp. (Ville)
v7: Remove unwanted comments (Manasi)
Cc: dri-devel@lists.freedesktop.org
Cc: Gaurav K Singh <gaurav.k.singh@intel.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Ville Syrjala <ville.syrjala@linux.intel.com>
Cc: Manasi Navare <manasi.d.navare@intel.com>
Signed-off-by: Anusha Srivatsa <anusha.srivatsa@intel.com>
Signed-off-by: Manasi Navare <manasi.d.navare@intel.com>
Reviewed-by: Manasi Navare <manasi.d.navare@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181128202628.20238-16-manasi.d.navare@intel.com
Anusha Srivatsa [Wed, 28 Nov 2018 20:26:26 +0000 (12:26 -0800)]
drm/i915/fec: Set FEC_READY in FEC_CONFIGURATION
If the panel supports FEC, the driver has to
set the FEC_READY bit in the dpcd register:
FEC_CONFIGURATION.
This has to happen before link training.
v2: s/intel_dp_set_fec_ready/intel_dp_sink_set_fec_ready
- change commit message. (Gaurav)
v3: rebased. (r-b Manasi)
v4: Use fec crtc state, before setting FEC_READY
bit. (Anusha)
v5: Move to intel_ddi.c
- Make the function static (Anusha)
v6: Dont pass state as a separate argument (Ville)
v7: (From Manasi)
* Correct the debug print (Ville)
Cc: dri-devel@lists.freedesktop.org
Cc: Gaurav K Singh <gaurav.k.singh@intel.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Ville Syrjala <ville.syrjala@linux.intel.com>
Cc: Manasi Navare <manasi.d.navare@intel.com>
Signed-off-by: Anusha Srivatsa <anusha.srivatsa@intel.com>
Signed-off-by: Manasi Navare <manasi.d.navare@intel.com>
Reviewed-by: Manasi Navare <manasi.d.navare@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181128202628.20238-15-manasi.d.navare@intel.com
Anusha Srivatsa [Wed, 28 Nov 2018 20:26:25 +0000 (12:26 -0800)]
i915/dp/fec: Add fec_enable to the crtc state.
For DP 1.4 and above, Display Stream compression can be
enabled only if Forward Error Correctin can be performed.
Add a crtc state for FEC. Currently, the state
is determined by platform, DP and DSC being
enabled. Moving forward we can use the state
to have error correction on other scenarios too
if needed.
v2:
- Control compression_enable with the fec_enable
parameter in crtc state and with intel_dp_supports_fec()
(Ville)
- intel_dp_can_fec()/intel_dp_supports_fec()(manasi)
v3: Check for FEC support along with setting crtc state.
v4: add checks to intel_dp_source_supports_dsc.(manasi)
- Move intel_dp_supports_fec() closer to
intel_dp_supports_dsc() (Anusha)
v5: Move fec check to intel_dp_supports_dsc(Ville)
v6: Remove warning. rebase.
v7: change crtc state to include DP sink and fec capability
of source.(Manasi)
v8: Set fec_enable in crtc in intel_dp_compute_config().
v9 (From Manasi):
* Combine the !edp and !fec_support check
* Derive dev_priv from intel_dp directly
v10 (From Manasi):
* Rebase
Suggested-by: Ville Syrjala <ville.syrjala@linux.intel.com>
Cc: dri-devel@lists.freedesktop.org
Cc: Ville Syrjala <ville.syrjala@linux.intel.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Manasi Navare <manasi.d.navare@intel.com>
Signed-off-by: Anusha Srivatsa <anusha.srivatsa@intel.com>
Signed-off-by: Manasi Navare <manasi.d.navare@intel.comk>
Reviewed-by: Manasi Navare <manasi.d.navare@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181128202628.20238-14-manasi.d.navare@intel.com
Manasi Navare [Wed, 28 Nov 2018 20:26:24 +0000 (12:26 -0800)]
drm/i915/dsc: Enable and disable appropriate power wells for VDSC
A separate power well 2 (PG2) is required for VDSC on eDP transcoder
whereas all other transcoders use the power wells associated with the
transcoders for VDSC.
This patch adds a helper to obtain correct power domain depending on
transcoder being used and enables/disables the power wells during
VDSC enabling/disabling.
v4:
* Get VDSC power domain only if compression en is set
in crtc_state (Ville, Imre)
v3:
* Call it intel_dsc_power_domain, add to
intel_ddi_get_power_domains (Ville)
v2:
* Fix tabs, const crtc_state, fix comments (Ville)
Suggested-by: Ville Syrjala <ville.syrjala@linux.intel.com>
Cc: Ville Syrjala <ville.syrjala@linux.intel.com>
Cc: Imre Deak <imre.deak@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Manasi Navare <manasi.d.navare@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181128202628.20238-13-manasi.d.navare@intel.com
Manasi Navare [Wed, 28 Nov 2018 20:26:23 +0000 (12:26 -0800)]
drm/i915/dp: Disable DSC in source by disabling DSS CTL bits
1. Disable Left/right VDSC branch in DSS Ctrl reg
depending on the number of VDSC engines being used
2. Disable joiner in DSS Ctrl reg
v4:
* Remove encoder, make crtc_state const (Ville)
v3 (From Manasi):
* Add Disable PG2 for VDSC on eDP
v2 (From Manasi):
* Use old_crtc_state to find dsc params
* Add a condition to disable only if
dsc state compression is enabled
* Use correct DSS CTL regs
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Ville Syrjala <ville.syrjala@linux.intel.com>
Cc: Anusha Srivatsa <anusha.srivatsa@intel.com>
Signed-off-by: Manasi Navare <manasi.d.navare@intel.com>
Signed-off-by: Gaurav K Singh <gaurav.k.singh@intel.com>
Reviewed-by: Anusha Srivatsa <anusha.srivatsa@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181128202628.20238-12-manasi.d.navare@intel.com
Manasi Navare [Wed, 28 Nov 2018 20:26:22 +0000 (12:26 -0800)]
drm/i915/dp: Configure Display stream splitter registers during DSC enable
Display Stream Splitter registers need to be programmed to enable
the joiner if two DSC engines are used and also to enable
the left and the right DSC engines. This happens as part of
the DSC enabling routine in the source in atomic commit.
v4:
* Remove redundant comment (Ville)
v3:
* Use cpu_transcoder instead of encoder->type (Ville)
v2:
* Rebase (Manasi)
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Ville Syrjala <ville.syrjala@linux.intel.com>
Cc: Anusha Srivatsa <anusha.srivatsa@intel.com>
Signed-off-by: Manasi Navare <manasi.d.navare@intel.com>
Reviewed-by: Anusha Srivatsa <anusha.srivatsa@intelcom>
Link: https://patchwork.freedesktop.org/patch/msgid/20181128202628.20238-11-manasi.d.navare@intel.com
Manasi Navare [Wed, 28 Nov 2018 20:26:21 +0000 (12:26 -0800)]
drm/i915/dp: Populate DSC PPS SDP and send PPS infoframes
DSC PPS secondary data packet infoframes are filled with
DSC picure parameter set metadata according to the DSC standard.
These infoframes are sent to the sink device and used during DSC
decoding.
v3:
* Rename to intel_dp_write_pps_sdp (Ville)
* Use const intel_crtc_state (Ville)
v2:
* Rebase ond drm-tip
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Ville Syrjala <ville.syrjala@linux.intel.com>
Cc: Anusha Srivatsa <anusha.srivatsa@intel.com>
Signed-off-by: Manasi Navare <manasi.d.navare@intel.com>
Reviewed-by: Anusha Srivatsa <anusha.srivatsa@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181128202628.20238-10-manasi.d.navare@intel.com
Manasi Navare [Wed, 28 Nov 2018 20:26:20 +0000 (12:26 -0800)]
drm/i915/dp: Use the existing write_infoframe() for DSC PPS SDPs
Infoframes are used to send secondary data packets. This patch
adds support for DSC Picture parameter set secondary data packets
in the existing write_infoframe helpers.
v3:
* Unused variables cleanup (Ville)
v2:
* Rebase on drm-tip (Manasi)
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Ville Syrjala <ville.syrjala@linux.intel.com>
Cc: Anusha Srivatsa <anusha.srivatsa@intel.com>
Signed-off-by: Manasi Navare <manasi.d.navare@intel.com>
Reviewed-by: Anusha Srivatsa <anusha.srivatsa@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181128202628.20238-9-manasi.d.navare@intel.com
Manasi Navare [Wed, 28 Nov 2018 20:26:19 +0000 (12:26 -0800)]
drm/i915/dp: Configure i915 Picture parameter Set registers during DSC enabling
After encoder->pre_enable() hook, after link training sequence is
completed, PPS registers for DSC encoder are configured using the
DSC state parameters in intel_crtc_state as part of DSC enabling
routine in the source. DSC enabling routine is called after
encoder->pre_enable() before enbaling the pipe and after
compression is enabled on the sink.
v7:
* Remove unnecessary comments, leftovers (Ville)
* No need for explicit val &= ~ (Ville)
v6:
intel_dsc_enable to be part of pre_enable hook (Ville)
v5:
* make crtc_state const (Ville)
v4:
* Use cpu_transcoder instead of encoder->type for using EDP transcoder
DSC registers(Ville)
* Keep all PSS regs together (Anusha)
v3:
* Configure Pic_width/2 for each VDSC engine when two VDSC engines per pipe
are used (Manasi)
* Add DSC slice_row_per_frame in PPS16 (Manasi)
v2:
* Enable PG2 power well for VDSC on eDP
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Ville Syrjala <ville.syrjala@linux.intel.com>
Cc: Anusha Srivatsa <anusha.srivatsa@intel.com>
Signed-off-by: Manasi Navare <manasi.d.navare@intel.com>
[manasi: fixup the line longer than 100 chars while applying]
Reviewed-by: Anusha Srivatsa <anusha.srivatsa@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181128202628.20238-8-manasi.d.navare@intel.com
Manasi Navare [Wed, 28 Nov 2018 20:26:18 +0000 (12:26 -0800)]
drm/i915/dsc: Add a power domain for VDSC on eDP/MIPI DSI
On Icelake, a separate power well PG2 is created for
VDSC engine used for eDP/MIPI DSI. This patch adds a new
display power domain for Power well 2.
v3:
* Call it POWER_DOMAIN_TRANSCODER_EDP_VDSC (Ville)
* Move it around TRANSCODER power domain defs (Ville)
v2:
* Fix the power well mismatch CI error (Ville)
* Rename as VDSC_PIPE_A (Imre)
* Fix a whitespace (Anusha)
* Fix Comments (Imre)
Cc: Ville Syrjala <ville.syrjala@linux.intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Imre Deak <imre.deak@intel.com>
Signed-off-by: Manasi Navare <manasi.d.navare@intel.com>
Reviewed-by: Ville Syrjala <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181128202628.20238-7-manasi.d.navare@intel.com
Gaurav K Singh [Wed, 28 Nov 2018 20:26:17 +0000 (12:26 -0800)]
drm/i915/dp: Enable/Disable DSC in DP Sink
This patch enables decompression support in sink device
before link training and disables the same during the
DDI disabling.
v3 (From manasi):
* Pass bool state to enable/disable (Ville)
v2:(From Manasi)
* Change the enable/disable function to take crtc_state
instead of intel_dp as an argument (Manasi)
* Use the compression_enable flag as part of crtc_state (Manasi)
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Ville Syrjala <ville.syrjala@linux.intel.com>
Cc: Anusha Srivatsa <anusha.srivatsa@intel.com>
Cc: Gaurav K Singh <gaurav.k.singh@intel.com>
Signed-off-by: Gaurav K Singh <gaurav.k.singh@intel.com>
Signed-off-by: Manasi Navare <manasi.d.navare@intel.com>
Reviewed-by: Anusha Srivatsa <anusha.srivatsa@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181128202628.20238-6-manasi.d.navare@intel.com
Gaurav K Singh [Wed, 28 Nov 2018 20:26:16 +0000 (12:26 -0800)]
drm/i915/dsc: Compute Rate Control parameters for DSC
This computation of RC params happens in the atomic commit phase
during compute_config() to validate if display stream compression
can be enabled for the requested mode.
v7 (From Manasi):
* Use DRM_DEBUG instead of DRM_ERROR (Ville)
* Use Error numberinstead of -1 (Ville)
v6 (From Manasi):
* Use 9 instead of 0x9 for consistency (Anusha)
v5 (From Manasi):
* Fix dim checkpatch warnings/checks
v4(From Gaurav):
* No change.Rebase on drm-tip
v3 (From Gaurav):
* Rebase on top of Manasi's latest series
* Return -ve value in case of failure scenarios (Manasi)
Fix review comments from Ville:
* Remove unnecessary comments
* Remove unnecessary paranthesis
* Add comments for few RC params calculations
v2 (From Manasi):
* Rebase Gaurav's patch from intel-gfx to gfx-internal
* Use struct drm_dsc_cfg instead of struct intel_dp
as a parameter
Cc: Manasi Navare <manasi.d.navare@intel.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Ville Syrjala <ville.syrjala@linux.intel.com>
Signed-off-by: Gaurav K Singh <gaurav.k.singh@intel.com>
Signed-off-by: Manasi Navare <manasi.d.navare@intel.com>
Reviewed-by: Anusha Srivatsa <anusha.srivatsa@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181128202628.20238-5-manasi.d.navare@intel.com
Gaurav K Singh [Thu, 29 Nov 2018 19:38:27 +0000 (11:38 -0800)]
drm/i915/dsc: Define & Compute VESA DSC params
This patches does the following:
1. This patch defines all the DSC parameters as per the VESA
DSC specification. These are stored in the encoder and used
to compute the PPS parameters to be sent to the Sink.
2. Compute all the DSC parameters which are derived from DSC
state of intel_crtc_state.
3. Compute all parameters that are VESA DSC specific
This computation happens in the atomic check phase during
compute_config() to validate if display stream compression
can be enabled for the requested mode.
v8 (From Manasi):
* DEBUG_KMS instead of DRM_ERROR for user triggerable
errors (Ville)
v7: (From Manasi)
* Dont use signed int for rc_range_params (Manasi)
* Mask the range_bpg_offset to use only 6 bits
* Add SPDX identifier (Chris Wilson)
v6 (From Manasi):
* Add a check for line_buf_depth return value (Anusha)
* Remove DRM DSC constants to different patch (Manasi)
v5 (From Manasi):
* Add logic to limit the max line buf depth for DSC 1.1 to 13
as per DSC 1.1 spec
* Fix dim checkpatch warnings/checks
v4 (From Gaurav):
* Rebase on latest drm tip
* rename variable name(Manasi)
* Populate linebuf_depth variable(Manasi)
v3 (From Gaurav):
* Rebase my previous patches on top of Manasi's latest patch
series
* Using >>n rather than /2^n (Manasi)
* Change the commit message to explain what the patch is doing(Gaurav)
Fixed review comments from Ville:
* Don't use macro TWOS_COMPLEMENT
* Mention in comment about the source of RC params
* Return directly from case statements
* Using single asssignment for assigning rc_range_params
* Using <<n rather than *2^n and removing the comments
about the fixed point numbers
v2 (From Manasi):
* Update logic for minor version to consider the dpcd value
and what supported by the HW platform
* Use DRM DSC config struct instead of intel_dp struct
* Move the DSC constants to DRM DSC header file
* Use u16, u8 where bigger data types not needed
* * Compute the DSC parameters as part of DSC compute config
since the computation can fail (Manasi)
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Ville Syrjala <ville.syrjala@linux.intel.com>
Cc: Anusha Srivatsa <anusha.srivatsa@intel.com>
Cc: Gaurav K Singh <gaurav.k.singh@intel.com>
Signed-off-by: Gaurav K Singh <gaurav.k.singh@intel.com>
Signed-off-by: Manasi Navare <manasi.d.navare@intel.com>
Co-developed-by: Manasi Navare <manasi.d.navare@intel.com>
Reviewed-by: Anusha Srivatsa <anusha.srivatsa@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181129193827.7914-1-manasi.d.navare@intel.com
Manasi Navare [Wed, 28 Nov 2018 20:26:14 +0000 (12:26 -0800)]
drm/i915/dp: Do not enable PSR2 if DSC is enabled
If a eDP panel supports both PSR2 and VDSC, our HW cannot
support both at a time. Give priority to PSR2 if a requested
resolution can be supported without compression else enable
VDSC and keep PSR2 disabled.
v4:
Fix the unrealted stuff removed during rebase (Ville)
v3:
* Rebase
v2:
* Add warning for DSC and PSR2 enabled together (DK)
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Manasi Navare <manasi.d.navare@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181128202628.20238-3-manasi.d.navare@intel.com
Manasi Navare [Wed, 28 Nov 2018 21:36:21 +0000 (13:36 -0800)]
drm/i915/dp: Compute DSC pipe config in atomic check
DSC params like the enable, compressed bpp, slice count and
dsc_split are added to the intel_crtc_state. These parameters
are set based on the requested mode and available link parameters
during the pipe configuration in atomic check phase.
These values are then later used to populate the remaining DSC
and RC parameters before enbaling DSC in atomic commit.
v15:
* Rebase over drm-tip
v14:
Remove leftovers, use dsc_bpc, refine dsc_compute_config (Ville)
v13:
* Compute DSC bpc only when DSC is req to be enabled (Ville)
v12:
* Override bpp with dsc dpcd color depth (Manasi)
v11:
* Const crtc_state, reject DSC on DP without FEC (Ville)
* Dont set dsc_split to false (Ville)
v10:
* Add a helper for dp_dsc support (Ville)
* Set pipe_config to max bpp, link params for DSC for now (Ville)
* Compute bpp - use dp dsc support helper (Ville)
v9:
* Rebase on top of drm-tip that now uses fast_narrow config
for edp (Manasi)
v8:
* Check for DSC bpc not 0 (manasi)
v7:
* Fix indentation in compute_m_n (Manasi)
v6 (From Gaurav):
* Remove function call of intel_dp_compute_dsc_params() and
invoke intel_dp_compute_dsc_params() in the patch where
it is defined to fix compilation warning (Gaurav)
v5:
Add drm_dsc_cfg in intel_crtc_state (Manasi)
v4:
* Rebase on refactoring of intel_dp_compute_config on tip (Manasi)
* Add a comment why we need to check PSR while enabling DSC (Gaurav)
v3:
* Check PPR > max_cdclock to use 2 VDSC instances (Ville)
v2:
* Add if-else for eDP/DP (Gaurav)
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Ville Syrjala <ville.syrjala@linux.intel.com>
Cc: Anusha Srivatsa <anusha.srivatsa@intel.com>
Cc: Gaurav K Singh <gaurav.k.singh@intel.com>
Signed-off-by: Manasi Navare <manasi.d.navare@intel.com>
Reviewed-by: Anusha Srivatsa <anusha.srivatsa@intel.com>
Reviewed-by: Ville Syrjala <ville.syrjala@linux.intel.com>
Acked-by: Jani Nikula <jani.nikula@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181128213621.21391-1-manasi.d.navare@intel.com
Manasi Navare [Wed, 28 Nov 2018 20:26:12 +0000 (12:26 -0800)]
drm/i915/dp: Add DSC params and DSC config to intel_crtc_state
Basic DSC parameters and DSC configuration data needs to be computed
for each of the requested mode during atomic check. This is
required since for certain modes, valid DSC parameters and config
data might not be computed in which case compression cannot be
enabled for that mode.
For that reason we need to add these params and config structure
to the intel_crtc_state so that if valid this state information
can directly be used while enabling DSC in atomic commit.
v2:
* Rebase on drm-tip (Manasi)
Cc: Gaurav K Singh <gaurav.k.singh@intel.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Ville Syrjala <ville.syrjala@linux.intel.com>
Cc: Anusha Srivatsa <anusha.srivatsa@intel.com>
Signed-off-by: Manasi Navare <manasi.d.navare@intel.com>
Reviewed-by: Anusha Srivatsa <anusha.srivatsa@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181128202628.20238-1-manasi.d.navare@intel.com
Ville Syrjälä [Tue, 25 Sep 2018 19:37:08 +0000 (22:37 +0300)]
drm/i915: Decouple SKL stride units from intel_fb_stride_alignment()
In the future framebuffer stride alignment requirements won't exactly
match the units in which skl+ plane stride is specified. So extract
the code for the skl+ stuff into a separate helper.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180925193714.25280-3-ville.syrjala@linux.intel.com
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Ville Syrjälä [Tue, 23 Oct 2018 16:02:01 +0000 (19:02 +0300)]
drm/i915: Make sure fb gtt offsets stay within 32bits
Let's try to make sure the fb offset computations never hit
an integer overflow by making sure the entire fb stays
below 32bits. framebuffer_check() in the core already does
the same check, but as it doesn't know about tiling some things
can slip through. Repeat the check in the driver with tiling
taken into account.
v2: Use add_overflows() after massaging it to work for me (Chris)
v3: Call it add_overflow_t() to match min_t() & co. (Chris)
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181023160201.9840-1-ville.syrjala@linux.intel.com
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Ville Syrjälä [Wed, 14 Nov 2018 21:07:29 +0000 (23:07 +0200)]
drm/i915: Pass the plane to icl_program_input_csc_coeff()
On icl+ the plane state that gets passed to update_slave() is not
the plane state of the plane we're programming. With NV12 the
plane state would be coming from the master (UV) plane whereas
the plane we're programming is the slave (Y) plane. For that reason
we need to explicitly pass around the slave plane (or we'd have to
otherwise deduce it by checking whether we were called via
.update_plane() or .update_slave()).
In the case of icl_program_input_csc_coeff() it's actually OK to
assume that we are always the master plane because the input CSC
only exists on HDR planes which can never be a slave plane. But
for consistency let's pass in the plane explicitly anyway.
While at it drop the "_coeff" from the function name since it's
kinda redundant, and this makes the name a bit shorter :)
Cc: Uma Shankar <uma.shankar@intel.com>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181114210729.16185-14-ville.syrjala@linux.intel.com
Reviewed-by: Uma Shankar <uma.shankar@intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Ville Syrjälä [Wed, 14 Nov 2018 21:07:28 +0000 (23:07 +0200)]
drm/i915: Rename the confusing 'plane_id' to 'color_plane'
A variable whose name is 'plane_id' is expected to be of the
enum plane_id type. In this case we have a raw int, which turns
out to refer to the plane of the framebuffer. Rename the variable
to 'color_plane' in line with the trend started earlier.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181114210729.16185-13-ville.syrjala@linux.intel.com
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Ville Syrjälä [Wed, 14 Nov 2018 21:07:27 +0000 (23:07 +0200)]
drm/i915: Commit skl+ planes in an order that avoids ddb overlaps
skl+ can go belly up if there are overlapping ddb allocations between
planes. If we could absolutely guarantee that we can perform the atomic
update within a single frame we shouldn't have to worry about this. But
we can't rely on that so let's steal the ddb overlap check trick from
skl_update_crtcs() and apply it to the plane updates. Since each step
of the sequence is free from ddb overlaps we don't have to worry about
a vblank sneaking up on us in the middle of the sequence. The partial
state that gets latched by the hardware will be safe. And unlike
skl_update_crtcs() we don't have to intoduce any extra vblank waits
on account of only having to worry about a single pipe.
v2: Fix typo in commit msg (Matt)
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181114210729.16185-12-ville.syrjala@linux.intel.com
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Ville Syrjälä [Tue, 27 Nov 2018 16:59:00 +0000 (18:59 +0200)]
drm/i915: Move ddb/wm programming into plane update/disable hooks on skl+
On SKL+ the plane WM/BUF_CFG registers are a proper part of each
plane's register set. That means accessing them will cancel any
pending plane update, and we would need a PLANE_SURF register write
to arm the wm/ddb change as well.
To avoid all the problems with that let's just move the wm/ddb
programming into the plane update/disable hooks. Now all plane
registers get written in one (hopefully atomic) operation.
To make that feasible we'll move the plane ddb tracking into
the crtc state. Watermarks were already tracked there.
v2: Rebase due to input CSC
v3: Split out a bunch of junk (Matt)
v4: Add skl_wm_add_affected_planes() to deal with
cursor special case and non-zero wm register reset value
v5: Drop the unrelated for_each_intel_plane_mask() fix (Matt)
Remove the redundant ddb memset() (Matt)
Cc: Matt Roper <matthew.d.roper@intel.com>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com> #v3
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181127165900.31298-1-ville.syrjala@linux.intel.com
Ville Syrjälä [Wed, 14 Nov 2018 21:07:25 +0000 (23:07 +0200)]
drm/i915: Don't pass dev_priv around so much
Simplify the calling convention of the skl+ watermark functions
by not passing around dev_priv needlessly. The callees have
what they need to dig it out anyway.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181114210729.16185-10-ville.syrjala@linux.intel.com
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Ville Syrjälä [Tue, 27 Nov 2018 16:57:26 +0000 (18:57 +0200)]
drm/i915: Clean up skl+ vs. icl+ watermark computation
Make a cleaner split between the skl+ and icl+ ways of computing
watermarks. This way skl_build_pipe_wm() doesn't have to know any
of the gritty details of icl+ master/slave planes.
We can also simplify a bunch of the lower level code by pulling
the plane visibility checks a bit higher up.
v2: WARN_ON(!visible) for the icl+ master plane case (Matt)
Cc: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181127165726.31122-1-ville.syrjala@linux.intel.com
Ville Syrjälä [Wed, 14 Nov 2018 21:07:23 +0000 (23:07 +0200)]
drm/i915: Pass the entire skl_plane_wm to skl_compute_transition_wm()
We have to pass both level 0 watermark struct and the transition
watermark struct to skl_compute_transition_wm(). Make life less
confusing by just passing the entire plane watermark struct that
contains both aforementioned structures.
Cc: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181114210729.16185-8-ville.syrjala@linux.intel.com
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Ville Syrjälä [Wed, 14 Nov 2018 21:07:22 +0000 (23:07 +0200)]
drm/i915: Remove some useless zeroing on skl+ wm calculations
We memset(0) the entire watermark struct the start, so there's no
need to clear things later on.
v2: Rebase due to some stale w/a removal
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181114210729.16185-7-ville.syrjala@linux.intel.com
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Ville Syrjälä [Wed, 14 Nov 2018 21:07:21 +0000 (23:07 +0200)]
drm/i915: Fix latency==0 handling for level 0 watermark on skl+
If the level 0 latency is 0 we can't do anything. Return an error
rather than success.
While this can't happen due to WaWmMemoryReadLatency, it can
happen if the user clears out the level 0 latency via debugfs.
v2: Clarify how how we can end here with zero level 0 latency (Matt)
Cc: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181114210729.16185-6-ville.syrjala@linux.intel.com
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Ville Syrjälä [Wed, 14 Nov 2018 21:07:20 +0000 (23:07 +0200)]
drm/i915: Pass the new crtc_state to ->disable_plane()
We're going to need access to the new crtc state in ->disable_plane()
for SKL+ wm/ddb programming and pre-skl pipe gamma/csc control. Pass
the crtc state down.
We'll also try to make intel_crtc_disable_planes() do the right
thing as much as it's possible. The fact that we don't have a
separate crtc state for the disabled state when we're going to
re-enable the crtc later means we might end up poking at a few
extra planes in there. But that's harmless. I suppose one might
argue that we wouldn't have to care about proper ddb/wm/csc/gamma
if the pipe is going to permanently disable anyway, but the state
checker probably cares so we should try our best to make sure
everything is programmed correctly even in that case.
v2: Fix the commit message a bit (Matt)
Cc: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181114210729.16185-5-ville.syrjala@linux.intel.com
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Ville Syrjälä [Tue, 27 Nov 2018 16:37:42 +0000 (18:37 +0200)]
drm/i915: Introduce crtc_state->update_planes bitmask
Keep track which planes need updating during the commit. For now
we set the bit for any plane that was or will be visible (including
icl+ nv12 slave planes). In the future I'll have need to update
invisible planes as well, for skl plane ddbs and for pre-skl pipe
gamma/csc control (which lives in the primary plane control register).
v2: Pimp the commit message to mention icl+ nv12 slave planes (Matt)
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181127163742.30215-1-ville.syrjala@linux.intel.com
Ville Syrjälä [Wed, 14 Nov 2018 21:07:18 +0000 (23:07 +0200)]
drm/i915: Move single buffered plane register writes to the end
The plane color correction registers are single buffered. So
ideally we would write them at the start of vblank just after the
double buffered plane registers have been latched. Since we have
no convenient way to do that for now let's at least move the
single buffered register writes to happen after the double
buffered registers have been written.
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181114210729.16185-3-ville.syrjala@linux.intel.com
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Ville Syrjälä [Wed, 14 Nov 2018 21:07:17 +0000 (23:07 +0200)]
drm/i915: Reorganize plane register writes to make them more atomic
Some observations about the plane registers:
- the control register will self-arm if the plane is not already
enabled, thus we want to write it as close to (or ideally after)
the surface register
- tileoff/linoff/offset/aux_offset are self-arming as well so we want
them close to the surface register as well
- color keying registers we maybe self arming before SKL. Not 100%
sure but we can try to keep them near to the surface register
as well
- chv pipe b csc register are double buffered but self arming so
moving them down a bit
- the rest should be mostly armed by the surface register so we can
safely write them first, and to just for some consistency let's try
to follow keep them in order based on the register offset
None of this will have any effect of course unless the vblank evasion
fails (which it still does sometimes). Another potential future benefit
might be pulling the non-self armings registers outside the vblank
evasion since they won't latch until the arming register has been
written. This would make the critical section a bit lighter and thus
less likely to exceed the deadline.
v2: Rebase due to input CSC
v3: Swap LINOFF/TILEOFF and KEYMSK/KEYMAX to actually follow
the last rule above (Matt)
Add a bit more rationale to the commit message (Matt)
Cc: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181114210729.16185-2-ville.syrjala@linux.intel.com
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Chris Wilson [Wed, 28 Nov 2018 13:53:25 +0000 (13:53 +0000)]
drm/i915: Mark up early pre-production Kabylakes
Mark A0 as the one and only pre-production variant of Kabylake and
remove its couple of workarounds, consigning them to the annals of
history.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Acked-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181128135325.10641-1-chris@chris-wilson.co.uk
Manasi Navare [Tue, 27 Nov 2018 21:41:08 +0000 (13:41 -0800)]
drm/dsc: Define the DSC 1.1 and 1.2 Line Buffer depth constants
DSC specification defines linebuf_depth which contains the
line buffer bit depth used to generate the bitstream.
These values are defined as per Table 4.1 in DSC 1.2 spec
v2 (From Manasi):
* Rename as MAX_LINEBUF_DEPTH for DSC 1.1 and DSC 1.2
Cc: dri-devel@lists.freedesktop.org
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Gaurav K Singh <gaurav.k.singh@intel.com>
Signed-off-by: Manasi Navare <manasi.d.navare@intel.com>
Acked-by: Sean Paul <seanpaul@chromium.org> (For merging through
drm-intel)
Reviewed-by: Anusha Srivatsa <anusha.srivatsa@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181127214125.17658-6-manasi.d.navare@intel.com
Manasi Navare [Tue, 27 Nov 2018 21:41:07 +0000 (13:41 -0800)]
drm/dsc: Add helpers for DSC picture parameter set infoframes
According to Display Stream compression spec 1.2, the picture
parameter set metadata is sent from source to sink device
using the DP Secondary data packet. An infoframe is formed
for the PPS SDP header and PPS SDP payload bytes.
This patch adds helpers to fill the PPS SDP header
and PPS SDP payload according to the DSC 1.2 specification.
v7:
* Use BUILD_BUG_ON() to protect changing struct size (Ville)
* Remove typecaseting (Ville)
* Include byteorder.h in drm_dsc.c (Ville)
* Correct kernel doc spacing (Anusha)
v6:
* Use proper sequence points for breaking down the
assignments (Chris Wilson)
* Use SPDX identifier
v5:
Do not use bitfields for DRM structs (Jani N)
v4:
* Use DSC constants for params that dont change across
configurations
v3:
* Add reference to added kernel-docs in
Documentation/gpu/drm-kms-helpers.rst (Daniel Vetter)
v2:
* Add EXPORT_SYMBOL for the drm functions (Manasi)
Cc: dri-devel@lists.freedesktop.org
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Ville Syrjala <ville.syrjala@linux.intel.com>
Cc: Anusha Srivatsa <anusha.srivatsa@intel.com>
Cc: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Manasi Navare <manasi.d.navare@intel.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Reviewed-by: Anusha Srivatsa <anusha.srivatsa@intel.com>
Acked-by: Sean Paul <seanpaul@chromium.org> (For merging through
drm-intel)
Link: https://patchwork.freedesktop.org/patch/msgid/20181127214125.17658-5-manasi.d.navare@intel.com
Srivatsa, Anusha [Tue, 27 Nov 2018 21:41:06 +0000 (13:41 -0800)]
drm/dsc: Define Rate Control values that do not change over configurations
DSC has some Rate Control values that remain constant
across all configurations. These are as per the DSC
standard.
v3:
* Define them in drm_dsc.h as they are
DSC constants (Manasi)
v2:
* Add DP_DSC_ prefix (Jani Nikula)
Cc: dri-devel@lists.freedesktop.org
Cc: Manasi Navare <manasi.d.navare@intel.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Ville Syrjala <ville.syrjala@linux.intel.com>
Cc: Gaurav K Singh <gaurav.k.singh@intel.com>
Cc: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Srivatsa, Anusha <anusha.srivatsa@intel.com>
Signed-off-by: Manasi Navare <manasi.d.navare@intel.com>
Reviewed-by: Manasi Navare <manasi.d.navare@intel.com>
Acked-by: Sean Paul <seanpaul@chromium.org> (For merging through
drm-intel)
Link: https://patchwork.freedesktop.org/patch/msgid/20181127214125.17658-4-manasi.d.navare@intel.com
Manasi Navare [Tue, 27 Nov 2018 21:41:05 +0000 (13:41 -0800)]
drm/dsc: Define VESA Display Stream Compression Capabilities
This defines all the DSC parameters as per the VESA DSC spec
that will be required for DSC encoder/decoder
v6: (From Manasi)
* Add a bit mask for RANGE_BPG_OFFSET for 6 bits(Manasi)
v5 (From Manasi)
* Add the RC constants as per the spec
v4 (From Manasi)
* Add the DSC_MUX_WORD_SIZE constants (Manasi)
v3 (From Manasi)
* Remove the duplicate define (Suggested By:Harry Wentland)
v2: Define this struct in DRM (From Manasi)
* Changed the data types to u8/u16 instead of unsigned longs (Manasi)
* Remove driver specific fields (Manasi)
* Move this struct definition to DRM (Manasi)
* Define DSC 1.2 parameters (Manasi)
* Use DSC_NUM_BUF_RANGES (Manasi)
* Call it drm_dsc_config (Manasi)
Cc: dri-devel@lists.freedesktop.org
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Ville Syrjala <ville.syrjala@linux.intel.com>
Cc: Anusha Srivatsa <anusha.srivatsa@intel.com>
Cc: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Manasi Navare <manasi.d.navare@intel.com>
Signed-off-by: Gaurav K Singh <gaurav.k.singh@intel.com>
Co-developed-by: Gaurav K Singh <gaurav.k.singh@intel.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Acked-by: Sean Paul <seanpaul@chromium.org> (For merging through
drm-intel)
Reviewed-by: Anusha Srivatsa <anusha.srivatsa@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181127214125.17658-3-manasi.d.navare@intel.com
Manasi Navare [Tue, 27 Nov 2018 21:41:04 +0000 (13:41 -0800)]
drm/dsc: Define Display Stream Compression PPS infoframe
This patch defines a new header file for all the DSC 1.2 structures
and creates a structure for PPS infoframe which will be used to send
picture parameter set secondary data packet for display stream compression.
All the PPS infoframe syntax elements are taken from DSC 1.2 specification
from VESA.
v4:
* Remove redundant blankline in doc (Ville)
* use drm_dsc namespace for all structs (Ville)
* Use packed struct (Ville)
v3:
* Add the SPDX shorthand (Chris Wilson)
v2:
* Do not use bitfields in the struct (Jani Nikula)
Cc: Gaurav K Singh <gaurav.k.singh@intel.com>
Cc: dri-devel@lists.freedesktop.org
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Ville Syrjala <ville.syrjala@linux.intel.com>
Cc: Anusha Srivatsa <anusha.srivatsa@intel.com>
Cc: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Manasi Navare <manasi.d.navare@intel.com>
Acked-by: Sean Paul <seanpaul@chromium.org> (For merging through
drm-intel)
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181127214125.17658-2-manasi.d.navare@intel.com
Manasi Navare [Tue, 27 Nov 2018 21:41:03 +0000 (13:41 -0800)]
drm/dsc: Modify DRM helper to return complete DSC color depth capabilities
DSC DPCD color depth register advertises its color depth capabilities
by setting each of the bits that corresponding to a specific color
depth. This patch defines those specific color depths and adds
a helper to return an array of color depth capabilities.
v2:
* Simplify the logic (Ville)
Signed-off-by: Manasi Navare <manasi.d.navare@intel.com>
Cc: Ville Syrjala <ville.syrjala@linux.intel.com>
Acked-by: Sean Paul <seanpaul@chromium.org> (For merging through
drm-intel)
Reviewed-by: Ville Syrjala <ville.syrjala@linux.intel.com>
Reviewed-by: Anusha Srivatsa <anusha.srivatsa@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181127214125.17658-1-manasi.d.navare@intel.com
Chris Wilson [Mon, 26 Nov 2018 09:56:10 +0000 (09:56 +0000)]
drm/i915: Skip engine serialisation for no-op seqno reset
If the engine's seqno is already at our target seqno (most likely it
hasn't been used since the last reset), we can skip serialising the
engine and leave it as is.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181126095610.20962-1-chris@chris-wilson.co.uk
Chris Wilson [Mon, 26 Nov 2018 12:28:21 +0000 (12:28 +0000)]
drm/i915/ringbuffer: 2-step restart
We may be simply restarting too fast for the culmudgeonly gen3/gen4 as
we still see missing interrupts following a reset. So let's try
restarting a little slower, first wake up the ring empty and then tell
it about the work it has to perform.
References: https://bugs.freedesktop.org/show_bug.cgi?id=108735
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181126122821.4537-1-chris@chris-wilson.co.uk
Chris Wilson [Fri, 23 Nov 2018 13:23:25 +0000 (13:23 +0000)]
drm/i915: Cache the error string
Currently, we convert the error state into a string every time we read
from sysfs (and sysfs reads in page size (4KiB) chunks). We do try to
window the string and only capture the portion that is being read, but
that means that we must always convert up to the window to find the
start. For a very large error state bordering on EXEC_OBJECT_CAPTURE
abuse, this is noticeable as it degrades to O(N^2)!
As we do not have a convenient hook for sysfs open(), and we would like
to keep the lazy conversion into a string, do the conversion of the
whole string on the first read and keep the string until the error state
is freed.
v2: Don't double advance simple_read_from_buffer
v3: Due to extreme pain of lack of vrealloc, use a scatterlist
v4: Keep the forward iterator loosely cached
v5: Stylistic improvements to reduce patch size
Reported-by: Jason Ekstrand <jason@jlekstrand.net>
Testcase: igt/gem_exec_capture/many*
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Cc: Jason Ekstrand <jason@jlekstrand.net>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181123132325.26541-1-chris@chris-wilson.co.uk
José Roberto de Souza [Wed, 21 Nov 2018 22:54:41 +0000 (14:54 -0800)]
drm/i915/hsw: Drop the stereo 3D enabled check in psr_compute_config()
We should not access hardware while computing config also we don't
support stereo 3D so this test was never true.
Suggested-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181121225441.18785-6-jose.souza@intel.com
José Roberto de Souza [Wed, 21 Nov 2018 22:54:40 +0000 (14:54 -0800)]
drm/i915: Keep PSR disabled after a driver reload after a PSR error
If a PSR error happened and the driver is reloaded, the EDP_PSR_IIR
will still keep the error set even after the reset done in the
irq_preinstall and irq_uninstall hooks.
And enabling in this situation cause the screen to freeze in the
first time that PSR HW tries to activate so lets keep PSR disabled
to avoid any rendering problems.
v5: rebased: using edp_psr_shift()
v4: Moved handling from intel_psr_compute_config() to
intel_psr_init() to avoid hardware access during compute(Ville)
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
squash
Link: https://patchwork.freedesktop.org/patch/msgid/20181121225441.18785-5-jose.souza@intel.com
José Roberto de Souza [Wed, 21 Nov 2018 22:54:39 +0000 (14:54 -0800)]
drm/i915: Disable PSR when a PSR aux error happen
While PSR is active hardware will do aux transactions by it self to
wakeup sink to receive a new frame when necessary. If that
transaction is not acked by sink, hardware will trigger this
interruption.
So let's disable PSR as it is a hint that there is problem with this
sink.
The removed FIXME was asking to manually train the link but we don't
need to do that as by spec sink should do a short pulse when it is
out of sync with source, we just need to make sure it is awaken and
the SDP header with PSR inactive set it will trigger the short pulse
with a error set in the link status.
v3: added workarround to fix scheduled work starvation cause by
to frequent PSR error interruption
v4: only setting irq_aux_error as we don't care in clear it and
not using dev_priv->irq_lock as consequence.
v5: rebased: using edp_psr_shift()
Cc: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181121225441.18785-4-jose.souza@intel.com
José Roberto de Souza [Wed, 21 Nov 2018 22:54:38 +0000 (14:54 -0800)]
drm/i915: Do not enable PSR in the next modeset after a error
When we detect a error and disable PSR, it is kept disabled until the
next modeset but as the sink already show signs that it do not
properly work with PSR lets disabled it for good to avoid any
additional flickering.
Cc: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181121225441.18785-3-jose.souza@intel.com
José Roberto de Souza [Wed, 21 Nov 2018 22:54:37 +0000 (14:54 -0800)]
drm/i915: Check PSR errors instead of retrain while PSR is enabled
When a PSR error happens sink sets the PSR error register and also
set the link status to a error status.
So in the short pulse handling it was returning earlier and doing a
full detection and attempting to retrain but it fails as PSR HW is
in change of the main-link.
Just call intel_psr_short_pulse() before
intel_dp_needs_link_retrain() is not the right fix as
intel_dp_needs_link_retrain() would return true and trigger a full
detection while PSR HW is still in change of main-link.
Check for PSR active is also not safe as it could be inactive due a
frontbuffer invalidate and still doing the PSR exit sequence.
v3: added comment in intel_dp_needs_link_retrain()
Cc: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181121225441.18785-2-jose.souza@intel.com
José Roberto de Souza [Wed, 21 Nov 2018 22:54:36 +0000 (14:54 -0800)]
drm/i915: Avoid a full port detection in the first eDP short pulse
Some eDP panels do not set a valid sink count value and even for the
ones that sets is should always be one for eDP, that is why it is not
cached in intel_edp_init_dpcd().
But intel_dp_short_pulse() compares the old count with the read one
if there is a mistmatch a full port detection will be executed, what
was happening in the first short pulse interruption of eDP panels
that sets sink count.
Instead of just skip the compasison for eDP panels, lets not read
the sink count at all for eDP.
v2: the previous version of this patch it was caching the sink count
in intel_edp_init_dpcd() but I was pointed out by Ville a patch that
handled a case of a eDP panel that do not set sink count and as sink
count is not used to eDP certification was choosed to just not read
it at all.
Cc: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181121225441.18785-1-jose.souza@intel.com
Lyude Paul [Wed, 21 Nov 2018 00:37:17 +0000 (19:37 -0500)]
drm/i915: Synchronize hpd work in i915_hpd_storm_ctl_show()
While trying to add a chamelium test for short HPD IRQs, I ran into
issues where a hotplug storm would be triggered, but the point at which
it would be reported by the kernel would be after igt actually finished
checking i915_hpd_storm_ctl's status. So, fix this by simply
synchronizing our IRQ work, dig_port_work, and hotplug_work before
printing out the HPD storm status in i915_hpd_storm_ctl_show().
Signed-off-by: Lyude Paul <lyude@redhat.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20181121003718.17704-1-lyude@redhat.com
Ville Syrjälä [Mon, 29 Oct 2018 18:34:53 +0000 (20:34 +0200)]
drm/i915: Eliminate the horrendous format check code
Replace the messy framebuffer format/modifier validation code
with a single call to drm_any_plane_has_format(). The code was
extremely annoying to maintain as you had to have a lot of platform
checks for different formats. The new code requires zero maintenance.
v2: Nuke the modifier checks as well since the core does that too now
v3: Call drm_any_plane_has_format() from the driver code
v4: Rebase
Cc: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181029183453.28541-2-ville.syrjala@linux.intel.com
Reviewed-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Jani Nikula [Thu, 22 Nov 2018 14:49:47 +0000 (16:49 +0200)]
drm/i915: Update DRIVER_DATE to
20181122
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Jani Nikula [Thu, 22 Nov 2018 14:03:03 +0000 (16:03 +0200)]
drm/i915: Update DRIVER_DATE to
20181122
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
projects / openwrt / staging / blogic.git / log