drm/i915/gen9+: Don't remove secondary power well requests

So far in an attempt to make sure all power wells get disabled during
display uninitialization the driver removed any secondary request bits
(BIOS, KVMR, DEBUG) that were set for a given power well. The known
source for these requests was DMC's request on power well 1 and the misc
IO power well. Since DMC is inactive (DC states are disabled) at the
point we disable these power wells, there shouldn't be any reason to
leave them on. However there are two problems with the above
assumption: Bspec requires that the misc IO power well stays enabled
(without providing a reason) and there can be KVMR requests that we
can't remove anyway (the KVMR request register is R/O). Atm, a KVMR
request can trigger a timeout WARN when trying to disable power wells.

To make the code aligned to Bspec and to get rid of the KVMR WARN, don't
try to remove the secondary requests, only detect them and stop polling
for the power well disabled state when any one is set.

Also add a comment about the timeout values required by Bspec when
enabling power wells and the fact that waiting for them to get disabled
is not required by Bspec.

Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=98564
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1498750622-14023-5-git-send-email-imre.deak@intel.com

drm/i915/bxt, glk: Fix assert on conditions for DC9 enabling

What we want to assert based on the conditions required by Bspec is that
power well 2 is disabled, so no need to check for other power wells.
In addition we can only check if the driver's request is removed, the
actual state depends on whether the other request bits are set or not
(BIOS, KVMR, DEBUG). So check only the driver's request bit.

Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1498750622-14023-4-git-send-email-imre.deak@intel.com

drm/i915/skl: Don't disable misc IO power well during display uninit

Bspec requires leaving the misc IO power well enabled during display
uninit, so align the code accordingly.

Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1498750622-14023-3-git-send-email-imre.deak@intel.com

drm/i915/gen9+: Add 10 us delay after power well 1/AUX IO pw disabling

Bspec requires a 10 us delay after disabling power well 1 and - if not
toggled on-demand - the AUX IO power wells during display uninit.

Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1498750622-14023-2-git-send-email-imre.deak@intel.com

drm/i915: Only free the oldest stale context before allocating

Currently, we move all unreferenced contexts to an RCU free list and
then onto a worker for eventual reaping. To compensate against this
growing into a long list with frequent allocations starving the system
of available memory, before we allocate a new context we reap all the
stale contexts. This puts all the cost of destroying the context into
the next allocator, which is presumably more sensitive to syscall
latency and unfair. We can limit the number of contexts being freed by
the new allocator to both keep the list trimmed and to allow the
allocator to be reasonably fast.

Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170705142634.18554-4-chris@chris-wilson.co.uk
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>

drm/i915: Drop request retirement before reaping stale contexts

Before we create a new context, we try and reap all the stale contexts
(i.e. those that are freed but waiting for a worker to come and return
their allocations to the system). Before we do this, we retire all
requests so that we clear any inflight no longer used contexts (who are
only being kept alived by those inflght requests). However, any context
that is finally unreferenced by this retirement is put onto an RCU list
and not available for immediately reaping, we stall for no immediate
benefit.

Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170705142634.18554-3-chris@chris-wilson.co.uk
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>

drm/i915: Move stale context reaping to common i915_gem_context_create

We need to reap the stale contexts for all new contexts, be they created
by user in i915_gem_context_ioctl or from opening a new file in
i915_gem_context_open. Both paths may be called very frequently
accumulating many stale contexts before any worker has a chance to run
and free their memory.

Fixes: 1acfc104cdf8 ("drm/i915: Enable rcu-only context lookups")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170705142634.18554-2-chris@chris-wilson.co.uk

drm/i915: Check new context against kernel_context after reporting an error

Avoid any pointer dereference in inspecting a potential PTR_ERR by
checking for the error pointer before checking for an invalid context.

Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170705142634.18554-1-chris@chris-wilson.co.uk

drm/i915: Setting pch_id for HSW/BDW in virtual environment

In a IGD passthrough environment, the real ISA bridge may doesn't exist.
then pch_id couldn't be correctly gotten from ISA bridge, but pch_id is
used to identify LPT_H and LPT_LP. Currently i915 treat all LPT pch as
LPT_H,then errors occur when i915 runs on LPT_LP machines with igd
passthrough.

This patch set pch_id for HSW/BDW according to IGD type and isn't fully
correct. But it solves such issue on HSW/BDW ult/ulx machines.
QA CI system is blocked by this issue for a long time, it's better that
we could merge it to unblock QA CI system.

We know the root cause is in device model of virtual passthrough, and
will resolve it in the future with several parts cooperation in kernel,
qemu and xen.

Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=99938

Signed-off-by: Xiong Zhang <xiong.y.zhang@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1497496305-5364-1-git-send-email-xiong.y.zhang@intel.com

drm: i915: sysfs: constify attribute_group structures.

attribute_groups are not supposed to change at runtime. All functions
working with attribute_groups provided by <linux/sysfs.h> work with const
attribute_group. So mark the non-const structs as const.

File size before:
   text    data     bss     dec     hex filename
   4028    1088       0    5116    13fc drivers/gpu/drm/i915/i915_sysfs.o

File size After adding 'const':
   text    data     bss     dec     hex filename
   4196     928       0    5124    1404 drivers/gpu/drm/i915/i915_sysfs.o

Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/13b5c875e677c10e6257be4fac31b2b6c77a494f.1499079914.git.arvind.yadav.cs@gmail.com

drm/i915/edp: Add a T12 panel delay quirk to fix DP AUX CH timeouts

This patch fixes the DP AUX CH timeouts observed during CI IGT
tests thus fixing the CI failures. This is done by adding a
quirk for a particular PCI device that requires the panel power
cycle delay (T12) to be set to 800ms which is 300msecs more than
the minimum value specified in the eDP spec. So a quirk is
implemented for that specific PCI device.

v4:
* Add Bugzilla links for FDO bugs in the commit message (Ville, Jani)
v3:
* Change some comments, specify the delay as 800 * 10 (Ville)
v2:
* Change the function and variable names to from PPS_T12_
to _T12 since it is a T12 delay (Clint)

Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=101144
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=101154
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=101167
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=101515
Cc: Ville Syrjala <ville.syrjala@linux.intel.com>
Cc: Clinton Taylor <clinton.a.taylor@intel.com>
Signed-off-by: Manasi Navare <manasi.d.navare@intel.com>
Reviewed-by: Clinton Taylor <clinton.a.taylor@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1498840428-23176-1-git-send-email-manasi.d.navare@intel.com
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>

drm/i915/skl+: Scaling not supported in IF-ID Interlace mode

GEN9+ Interlace fetch mode doesn't support pipe/plane scaling,
This patch adds check to fail the flip if pipe/plane scaling is
requested in Interlace fetch mode.

Changes since V1:
 - move check to skl_update_scaler (ville)
 - mode to adjusted_mode (ville)
 - combine pipe/plane scaling check
Changes since V2:
 - Indentation fix
 - Added TODO to handle/reject NV12 with interlace mode

Signed-off-by: Mahesh Kumar <mahesh1.kumar@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170630121100.20159-3-mahesh1.kumar@intel.com
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>

drm/i915/skl+: Check for supported plane configuration in Interlace mode

In Gen9 platform Interlaced fetch mode doesn't support following plane
configuration:
 - Y/Yf tiling
 - 90/270 rotation
 - YUV420 hybrid planar source pixel formats.

This patch adds check to fail the flip if any of the above configuration
is requested.

Changes since V1:
 - handle checks in intel_plane_atomic_check_with_state (ville)
 - takeout plane scaler checks combile with pipe scaler in next patch
Changes since V2:
 - No need to check for NV12 as it need scaling, so it will be rejected
   by scaling check (ville)

Signed-off-by: Mahesh Kumar <mahesh1.kumar@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170630121100.20159-2-mahesh1.kumar@intel.com
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=90238
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>

drm/i915/fbdev: Check for existence of ifbdev->vma before operations

Commit fabef825626d ("drm/i915: Drop struct_mutex around frontbuffer
flushes") adds a dependency to ifbdev->vma when flushing the framebufer,
but the checks are only against the existence of the ifbdev->fb and not
against ifbdev->vma. This leaves a window of opportunity where we may
try to operate on the fbdev prior to it being probed (thanks to
asynchronous booting).

Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=101534
Fixes: fabef825626d ("drm/i915: Drop struct_mutex around frontbuffer flushes")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Daniel Vetter <daniel.vetter@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170622160211.783-1-chris@chris-wilson.co.uk
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: stable@vger.kernel.org

drm/i915: Fix use-after-free of context during free_contexts

When iterating the list of contexts to free, we need to use a safe
iterator as we are freeing the link as we go. Pass an extra thick brown
paper bag.

Fixes: 5f09a9c8ab6b ("drm/i915: Allow contexts to be unreferenced locklessly")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Matthew Auld <matthew.auld@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170630230517.1938-1-chris@chris-wilson.co.uk
Reviewed-by: Matthew Auld <matthew.auld@intel.com>

drm/i915: Prevent kernel panic when reading/writing compliance debugfs files, v2.

When reading all debugfs files on a system with DP-MST the kernel panics
on a null pointer dereference because intel_dp is null for a DP-MST
connector. Detect this case and skip those connectors.

Also fix the write for the DP compliance file in the same way.

Changes since v1:
- Fix i915_displayport_test_active_write too. (DK)

Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Cc: Manasi Navare <manasi.d.navare@intel.com>
Reviewed-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170626081835.24251-1-maarten.lankhorst@linux.intel.com

drm/i915: Hold RPM wakelock while initializing OA buffer

OA buffer initialization involves access to HW registers to set
the OA base, head and tail. Ensure device is awake while setting
these. With this, all oa.ops are covered under RPM and forcewake
wakelock.

Cc: Lionel Landwerlin <lionel.g.landwerlin@intel.com>
Signed-off-by: Sagar Arun Kamble <sagar.a.kamble@intel.com>
Reviewed-by: Lionel Landwerlin <lionel.g.landwerlin@intel.com>
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1498585181-23048-1-git-send-email-sagar.a.kamble@intel.com
Fixes: d79651522e89c ("drm/i915: Enable i915 perf stream for Haswell OA unit")
Cc: <stable@vger.kernel.org> # v4.11+

drm/i915: Update DRIVER_DATE to 20170703

Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

drm/i915/cnl: Fix the CURSOR_COEFF_MASK used in DDI Vswing Programming

The Cursor Coeff is lower 6 bits in the PORT_TX_DW4 register
and hence the CURSOR_COEFF_MASK should be (0x3F << 0)

Fixes: 04416108ccea ("drm/i915/cnl: Add registers related to voltage
swing sequences.")
Signed-off-by: Manasi Navare <manasi.d.navare@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1498785241-21138-1-git-send-email-manasi.d.navare@intel.com

drm/i915/cfl: Fix Workarounds.

During the review of Coffee Lake workarounds Mika pointed out
that WaDisableKillLogic and GEN9_DISABLE_OCL_OOB_SUPPRESS_LOGIC
should be removed from CFL and with that I should carry the rv-b.

However when doing the v2 I removed another Workaround that should
remain because although not mentioned by spec the history of hangs
around it advocates on its favor.

On some follow-up patches I continued operating on the wrong
workardound, but Ville noticed that, so here is the fix for the
current CFL code that is upstream already.

Fixes: 46c26662d2f ("drm/i915/cfl: Introduce Coffee Lake workarounds.")
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Cc: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>

drm/i915: Avoid undefined behaviour of "u32 >> 32"

When computing a hash for looking up relocation target handles in an
execbuf, we start with a large size for the hashtable and proceed to
halve it until the allocation succeeds. The final attempt is with an
order of 0 (i.e. a single element). This means that we then pass bits=0
to hash_32() which then computes "hash >> (32 - 0)" to lookup the single
element. Right shifting a value by the width of the operand is
undefined, so limit the smallest hash table we use to order 1.

v2: Keep the retry allocation flag for the final pass

Fixes: 4ff4b44cbb70 ("drm/i915: Store a direct lookup from object handle to vma")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170629150425.27508-1-chris@chris-wilson.co.uk

drm/i915: reintroduce VLV/CHV PFI programming power domain workaround

There are still cases on these platforms where an attempt is made to
configure the CDCLK while the power domain is off, like when coming back
from a suspend.  So the workaround below is still needed.

This effectively reverts commit 63ff30442519 ("drm/i915: Nuke the
VLV/CHV PFI programming power domain workaround").

Cc: stable@vger.kernel.org
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=101517
Suggested-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Gabriel Krisman Bertazi <krisman@collabora.co.uk>
Link: http://patchwork.freedesktop.org/patch/msgid/20170628210605.4994-1-krisman@collabora.co.uk
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>

drm/i915: Avoid keeping waitboost active for signaling threads

Once a client has requested a waitboost, we keep that waitboost active
until all clients are no longer waiting. This is because we don't
distinguish which waiter deserves the boost. However, with the advent of
fence signaling, the signaler threads appear as waiters to the RPS
interrupt handler. So instead of using a single boolean to track when to
keep the waitboost active, use a counter of all outstanding waitboosted
requests.

At this point, I have removed all vestiges of the rate limiting on
clients. Whilst this means that compositors should remain more fluid,
it also means that boosts are more prevalent. See commit b29c19b64528
("drm/i915: Boost RPS frequency for CPU stalls") for a longer discussion
on the pros and cons of both approaches.

A drawback of this implementation is that it requires constant request
submission to keep the waitboost trimmed (as it is now cancelled when the
request is completed). This will be fine for a busy system, but near
idle the boosts may be kept for longer than desired (effectively tens of
vblanks worstcase) and there is a reliance on rc6 instead.

v2: Remove defunct rps.client_lock

Reported-by: Michał Winiarski <michal.winiarski@intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Michał Winiarski <michal.winiarski@intel.com>
Reviewed-by: Michał Winiarski <michal.winiarski@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170628123548.9236-1-chris@chris-wilson.co.uk

drm/i915: Drop flushing of the object free list/worker from i915_gem_suspend

i915_gem_suspend() is called from all of our finalization paths
(suspend, hibernate, unload). i915_gem_drain_freed_objects() adds an
arbitrary delay as it uses an rcu_barrier() to ensure that there are no
more freed objects in flight, and this delay causes a large amount of
variability in suspend timings. For S3 suspend, we do not need to free
pages as doing so does not impact at all upon the system in its
suspended state, unlike S4 hibernation where we do want the hibernation
image to be as small as possible. Therefore we can forgo waiting inside
i915_gem_suspend(), so long as we ensure that we do cleanup before
unload (see i915_gem_load_cleanup()) and prefer to reap our objects
prior to hibernation (see i915_gem_freeze()).

Removing the rcu_barrier() from i915_gem_suspend() improves S3 latency
by about 30ms on Skylake (ymmv).

Reported-by: David Weinehall <david.weinehall@linux.intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: David Weinehall <david.weinehall@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170627173731.11566-1-chris@chris-wilson.co.uk
Tested-by: David Weinehall <david.weinehall@linux.intel.com>
Reviewed-by: David Weinehall <david.weinehall@linux.intel.com>

drm/i915: Cancel pending execlists irq handler upon idling

Due to the slight asynchronicity in handling the execlists interrupts
(i.e. we defer the work to a handler that may consume more than one
interrupt event), when the engine is idle we may still have an irq
tasklet queued (especially when it has been deferred to a ksoftirqd).
At the beginning of the tasklet, we assert that we do hold a device
wakeref for the access we are about to perform. This assumes that when
we idle and release the GT wakeref, all execlists work has been
completed (since the elsp tracking says the hw is idle). However, there
may still be a tasklet queued, so as we mark the engine idle, also
cancel any pending tasklet.

Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170627152510.28589-1-chris@chris-wilson.co.uk
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>

drm/i915: Fix an error checking test

'dma_buf_vmap' returns NULL on error, not an error pointer.

Fixes: 6cca22ede8a4 ("drm/i915: Add some mock tests for dmabuf interop")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Link: http://patchwork.freedesktop.org/patch/msgid/20170627053854.21152-1-christophe.jaillet@wanadoo.fr
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>

drm/i915/selftests: Fix mutex imbalance for igt_render_engine_reset_fallback

Smatch spots:

drivers/gpu/drm/i915/selftests/intel_hangcheck.c:669 igt_render_engine_reset_fallback() error: double unlock 'mutex:&i915->drm.struct_mutex'

Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: http://patchwork.freedesktop.org/patch/msgid/20170623131907.24236-1-chris@chris-wilson.co.uk
Reviewed-by: Michel Thierry <michel.thierry@intel.com>

drm/i915: Disable MSI for all pre-gen5

We have pretty clear evidence that MSIs are getting lost on g4x and
somehow the interrupt logic doesn't seem to recover from that state
even if we try hard to clear the IIR.

Disabling IER around the normal IIR clearing in the irq handler isn't
sufficient to avoid this, so the problem really seems to be further
up the interrupt chain. This should guarantee that there's always
an edge if any IIR bits are set after the interrupt handler is done,
which should normally guarantee that the CPU interrupt is generated.
That approach seems to work perfectly on VLV/CHV, but apparently
not on g4x.

MSI is documented to be broken on 965gm at least. The chipset spec
says MSI is defeatured because interrupts can be delayed or lost,
which fits well with what we're seeing on g4x. Previously we've
already disabled GMBUS interrupts on g4x because somehow GMBUS
manages to raise legacy interrupts even when MSI is enabled.

Since there's such widespread MSI breakahge all over in the pre-gen5
land let's just give up on MSI on these platforms.

Seqno reporting might be negatively affected by this since the legcy
interrupts aren't guaranteed to be ordered with the seqno writes,
whereas MSI interrupts may be? But an occasioanlly missed seqno
seems like a small price to pay for generally working interrupts.

Cc: stable@vger.kernel.org
Cc: Diego Viola <diego.viola@gmail.com>
Tested-by: Diego Viola <diego.viola@gmail.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=101261
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170626203051.28480-1-ville.syrjala@linux.intel.com
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>

drm/i915/dp: Remove -1/+1 from t11_t12 for Gen9_LP/CNP case

Now the VBT.seq->t11_t12 value adds 100ms to both Gen9_LP
as well as non Gen9_LP cases so no need to special case
and do -1 during HW readout and +1 during pp_div write
for Gen9_LP/CNP case.

Reviewed-by: Ville Syrjala <ville.syrjala@linux.intel.com>
Signed-off-by: Manasi Navare <manasi.d.navare@intel.com>
Suggested-by: Ville Syrjala <ville.syrjala@linux.intel.com>
Cc: Ville Syrjala <ville.syrjala@linux.intel.com>
Cc: Clint Taylor <clinton.a.taylor@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1498504905-21067-2-git-send-email-manasi.d.navare@intel.com
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>

drm/i915/dp: Fix the t11_t12 panel power cycle delay from VBT read

When we read the VBT t11_t12 value for panel power cycle delay,
it is a zero based value so we need to 100ms to that. And then it
needs to be multiplied by 10 to store it in 100usecs unit same as
SW VBT.

v3:
* Add it as part of series
v2:
* Change the VBT value instead of HW readout and pp div (Ville Syrjala)

Reviewed-by: Ville Syrjala <ville.syrjala@linux.intel.com>
Signed-off-by: Manasi Navare <manasi.d.navare@intel.com>
Cc: Ville Syrjala <ville.syrjala@linux.intel.com>
Cc: Clint Taylor <clinton.a.taylor@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1498504905-21067-1-git-send-email-manasi.d.navare@intel.com
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>

drm/i915: Break modeset deadlocks on reset

Trying to do a modeset from within a reset is fraught with danger. We
can fall into a cyclic deadlock where the modeset is waiting on a
previous modeset that is waiting on a request, and since the GPU hung
that request completion is waiting on the reset. As modesetting doesn't
allow its locks to be broken and restarted, or for its *own* reset
mechanism to take over the display, we have to do something very
evil instead. If we detect that we are stuck waiting to prepare the
display reset (by using a very simple timeout), resort to cancelling all
in-flight requests and throwing the user data into /dev/null, which is
marginally better than the driver locking up and keeping that data to
itself.

This is not a fix; this is just a workaround that unbreaks machines
until we can resolve the deadlock in a way that doesn't lose data!

v2: Move the retirement from set-wegded to the i915_reset() error path,
after which we no longer any delayed worker cleanup for
i915_handle_error()
v3: C abuse for syntactic sugar
v4: Cover all waits with the timeout to catch more driver breakage

References: https://bugs.freedesktop.org/show_bug.cgi?id=99093
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Mika Kuoppala <mika.kuoppala@intel.com>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170622105625.16952-1-chris@chris-wilson.co.uk
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>

drm/i915: Add option to support dynamic backlight via DPCD

This patch adds option to enable dynamic backlight for eDP
panel that supports this feature via DPCD register and
set minimum / maximum brightness to 0% and 100% of the
normal brightness.

Signed-off-by: Puthikorn Voravootivat <puthik@chromium.org>
Reviewed-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/20170622190339.142671-4-puthik@chromium.org

drm/i915: Add heuristic to determine better way to adjust brightness

Add heuristic to decide that AUX or PWM pin should use for
backlight brightness adjustment and modify i915 param description
to have auto, force disable, and force enable.

The heuristic to determine that using AUX pin is better than using
PWM pin is that the panel support any of the feature list here.
- Regional backlight brightness adjustment
- Backlight PWM frequency set
- More than 8 bits resolution of brightness level
- Backlight enablement via AUX and not by BL_ENABLE pin

Signed-off-by: Puthikorn Voravootivat <puthik@chromium.org>
Reviewed-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/20170622190339.142671-3-puthik@chromium.org

drm/i915: Set PWM divider to match desired frequency in vbt

Read desired PWM frequency from panel vbt and calculate the
value for divider in DPCD address 0x724 and 0x728 to have
as many bits as possible for PWM duty cyle for granularity of
brightness adjustment while the frequency divisor is still
within 25% of the desired value.

Signed-off-by: Puthikorn Voravootivat <puthik@chromium.org>
Reviewed-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/20170622190339.142671-2-puthik@chromium.org

drm/i915: Always use 9 bits of the LPC bridge device ID for PCH detection

Make the code less confusiong by always using the top 9 bits of the
LPC bridge device ID to detect the PCH type. We need to add a bit of
new code for WPT, and we need to adjust the KBP ID as well. All the
other pre-CNP IDs are fine as is.

The virtualization cases I think are fine. These P2X and P3X IDs
actually just look like the old PIIX4 and PIIX3 IDs to me. Not sure
why they're not called PIIX3/4 though. The qemu one has a comment
saying the full ID is 0x2918 which is fine with 9 bits.

v2: Keep the CNP ID as 0xa300 (DK)

Cc: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170621174944.23306-1-ville.syrjala@linux.intel.com

drm/i915: Clean up some expressions

Write the '!(SNB||IVB)' checks in the CPT/PPT detections
as '!SNB && !IVB' to make it less messy looking, and clear out
some useless parens the from the virtualization PCH detection case.

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170620130310.13245-5-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>

drm/i915: Document that PPT==CPT and WPT==LPT

For our purposes PPT is equivalent to CPT, and WPT is equivalent to
LPT. Document that fact.

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170620130310.13245-4-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>

drm/i915: s/Couar/Cougar/

Fix a typo in the PCH type debug message.

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170620130310.13245-3-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>

drm/i915: Use HAS_PCH_CPT() everywhere

We have a few cases comparing pch_type directly. Let's just replace
them with HAS_PCH_CPT() since CPT/PPT is what they're looking for.

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170620130310.13245-2-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>

drm/i915: pass the vma to insert_entries

The vma already contains most of the information we need for insertion.
But also in preparation for supporting huge gtt pages, it would be
useful to know the details of the vma, such that we can we can easily
determine the page sizes we are allowed to use when inserting into the
48b PPGTT.  This is especially true for 64K where we can't just
arbitrarily use it, since we require aligning/padding the vm space to
2M, which sometimes we can't enforce in the upper levels.

Suggested-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Matthew Auld <matthew.auld@intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: http://patchwork.freedesktop.org/patch/msgid/20170622095836.6800-1-matthew.auld@intel.com
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>

drm/i915: Clear execbuf's vma backpointer upon release

commit 2889caa92321 ("drm/i915: Eliminate lots of iterations over the
execobjects array") jiggled around the error handling and replace a test
that we cleaned up properly after ourselves with an assertion. That
assertion failed because in the release function (moments after the
assertion) we were indeed forgetting to mark the vma as cleared. The
consequence was when testing an invalid relocation address, we would try
to release the vma twice (following the couple of attempts to verify the
address) and on the second release notice that the first release was
incomplete.

Testcase: igt/gem_reloc_overflow/invalid-address
Fixes: 2889caa92321 ("drm/i915: Eliminate lots of iterations over the execobjects array")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170622104722.2583-1-chris@chris-wilson.co.uk
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>

drm/i915: Cancel pending execlist tasklet upon wedging

Highly unlikely, but if the stop_machine() did suspend the tasklet, we
want to make sure that when it wakes it finds there is nothing to do.
Otherwise, it will loudly complain that the ELSP port tracking no longer
matches the hardware, and we will be mightly confused.

Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170621124804.4529-1-chris@chris-wilson.co.uk
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>

drm/i915: Hold struct_mutex for per-file stats in debugfs/i915_gem_object

As we walk the obj->vma_list in per_file_stats(), we need to hold
struct_mutex to prevent alteration of that list.

Fixes: 1d2ac403ae3b ("drm: Protect dev->filelist with its own mutex")
Fixes: c84455b4bacc ("drm/i915: Move debug only per-request pid tracking from request to ctx")
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=101460
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Daniel Vetter <daniel.vetter@intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170617115744.4452-1-chris@chris-wilson.co.uk
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>

drm/i915: Assert the vma's active tracking is clear before free

In looking at a use-after-free on Baytrail, it looks like the VMA's
activity tracking is suspect. Add some asserts to catch freeing the VMA
before we have decoupled all of its i915_gem_active trackers.

References: https://bugs.freedesktop.org/show_bug.cgi?id=101511
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@linux.intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170620124321.1108-3-chris@chris-wilson.co.uk
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@linux.intel.com>

drm/i915: Retire the VMA's fence tracker before unbinding

Since we may track unfenced access (GPU access to the vma that
explicitly requires no fence), vma->last_fence may be set without any
attached fence (vma->fence) and so will not be flushed when we call
i915_vma_put_fence(). Since we stopped doing a full retire of the
activity trackers for unbind, we need to explicitly retire each tracker.

Fixes: b0decaf75bd9 ("drm/i915: Track active vma requests")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Tvrtko Ursulin <tvrtko.ursulin@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170620124321.1108-1-chris@chris-wilson.co.uk
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@linux.intel.com>

drm/i915: select CRC32

kbuild test robot found a build failure when building with thin
archives:

http://marc.info/?l=linux-kbuild&m=149802285009737&w=2

Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/20170621063420.24913-1-npiggin@gmail.com

drm/i915: Pass the right flags to i915_vma_move_to_active()

i915_vma_move_to_active() takes the execobject flags and not a boolean!
Instead of passing EXEC_OBJECT_WRITE we passed true [i.e.
EXEC_OBJECT_NEEDS_FENCE] causing us to start tracking the
vma->last_fence access and since we forgot to clear that on unbinding,
we caused a use-after-free.

[  321.263854] BUG: KASAN: use-after-free in i915_gem_request_retire+0x1728/0x1740 [i915]
[  321.264001] Read of size 8 at addr ffff880100fc67d8 by task gem_exec_reloc/2868

[  321.264181] CPU: 0 PID: 2868 Comm: gem_exec_reloc Not tainted 4.12.0-rc6-CI-Custom_2759+ #1
[  321.264195] Hardware name: GIGABYTE GB-BXBT-1900/MZBAYAB-00, BIOS F6 02/17/2015
[  321.264208] Call Trace:
[  321.264234]  dump_stack+0x67/0x99
[  321.264260]  print_address_description+0x77/0x290
[  321.264437]  ? i915_gem_request_retire+0x1728/0x1740 [i915]
[  321.264459]  kasan_report+0x269/0x350
[  321.264487]  __asan_report_load8_noabort+0x14/0x20
[  321.264660]  i915_gem_request_retire+0x1728/0x1740 [i915]
[  321.264841]  ? intel_ring_context_pin+0x131/0x690 [i915]
[  321.265021]  i915_gem_request_alloc+0x2c6/0x1220 [i915]
[  321.265044]  ? _raw_spin_unlock_irqrestore+0x3d/0x60
[  321.265226]  i915_gem_do_execbuffer+0xac0/0x2a20 [i915]
[  321.265250]  ? __lock_acquire+0xceb/0x5450
[  321.265269]  ? entry_SYSCALL_64_fastpath+0x1c/0xb1
[  321.265291]  ? kvmalloc_node+0x6b/0x80
[  321.265310]  ? kvmalloc_node+0x6b/0x80
[  321.265489]  ? eb_relocate_slow+0xbe0/0xbe0 [i915]
[  321.265520]  ? ___slab_alloc.constprop.28+0x2ab/0x3d0
[  321.265549]  ? debug_check_no_locks_freed+0x280/0x280
[  321.265591]  ? __might_fault+0xc6/0x1b0
[  321.265782]  i915_gem_execbuffer2+0x14a/0x3f0 [i915]
[  321.265815]  drm_ioctl+0x4ba/0xaa0
[  321.265986]  ? i915_gem_execbuffer+0xde0/0xde0 [i915]
[  321.266017]  ? drm_getunique+0x270/0x270
[  321.266068]  do_vfs_ioctl+0x17f/0xfa0
[  321.266091]  ? __fget+0x1ba/0x330
[  321.266112]  ? lock_acquire+0x390/0x390
[  321.266133]  ? ioctl_preallocate+0x1d0/0x1d0
[  321.266164]  ? __fget+0x1db/0x330
[  321.266194]  ? __fget_light+0x79/0x1f0
[  321.266219]  SyS_ioctl+0x3c/0x70
[  321.266247]  entry_SYSCALL_64_fastpath+0x1c/0xb1
[  321.266265] RIP: 0033:0x7fcede207357
[  321.266279] RSP: 002b:00007ffef0effe58 EFLAGS: 00000246 ORIG_RAX: 0000000000000010
[  321.266307] RAX: ffffffffffffffda RBX: 0000000000000002 RCX: 00007fcede207357
[  321.266321] RDX: 00007ffef0effef0 RSI: 0000000040406469 RDI: 0000000000000004
[  321.266335] RBP: ffffffff812097c6 R08: 0000000000000008 R09: 0000000000000000
[  321.266349] R10: 0000000000000008 R11: 0000000000000246 R12: ffff880116bcff98
[  321.266363] R13: ffffffff81cb7cb3 R14: ffff880116bcff70 R15: 0000000000000000
[  321.266385]  ? __this_cpu_preempt_check+0x13/0x20
[  321.266406]  ? trace_hardirqs_off_caller+0x1d6/0x2c0

[  321.266487] Allocated by task 2868:
[  321.266568]  save_stack_trace+0x16/0x20
[  321.266586]  kasan_kmalloc+0xee/0x180
[  321.266602]  kasan_slab_alloc+0x12/0x20
[  321.266620]  kmem_cache_alloc+0xc7/0x2e0
[  321.266795]  i915_vma_instance+0x28c/0x1540 [i915]
[  321.266964]  eb_lookup_vmas+0x5a7/0x2250 [i915]
[  321.267130]  i915_gem_do_execbuffer+0x69a/0x2a20 [i915]
[  321.267296]  i915_gem_execbuffer2+0x14a/0x3f0 [i915]
[  321.267315]  drm_ioctl+0x4ba/0xaa0
[  321.267333]  do_vfs_ioctl+0x17f/0xfa0
[  321.267350]  SyS_ioctl+0x3c/0x70
[  321.267369]  entry_SYSCALL_64_fastpath+0x1c/0xb1

[  321.267428] Freed by task 177:
[  321.267502]  save_stack_trace+0x16/0x20
[  321.267521]  kasan_slab_free+0xad/0x180
[  321.267539]  kmem_cache_free+0xc5/0x340
[  321.267710]  i915_vma_unbind+0x666/0x10a0 [i915]
[  321.267880]  i915_vma_close+0x23a/0x2f0 [i915]
[  321.268048]  __i915_gem_free_objects+0x17d/0xc70 [i915]
[  321.268215]  __i915_gem_free_work+0x49/0x70 [i915]
[  321.268234]  process_one_work+0x66f/0x1410
[  321.268252]  worker_thread+0xe1/0xe90
[  321.268269]  kthread+0x304/0x410
[  321.268285]  ret_from_fork+0x27/0x40

[  321.268346] The buggy address belongs to the object at ffff880100fc6640
                which belongs to the cache i915_vma of size 656
[  321.268550] The buggy address is located 408 bytes inside of
                656-byte region [ffff880100fc6640, ffff880100fc68d0)
[  321.268741] The buggy address belongs to the page:
[  321.268837] page:ffffea000403f000 count:1 mapcount:0 mapping:          (null) index:0xffff880100fc5980 compound_mapcount: 0
[  321.269045] flags: 0x8000000000008100(slab|head)
[  321.269147] raw: 8000000000008100 0000000000000000 ffff880100fc5980 00000001001e001d
[  321.269312] raw: ffffea0004038e20 ffff880116b46240 ffff88011646c640 0000000000000000
[  321.269484] page dumped because: kasan: bad access detected

[  321.269665] Memory state around the buggy address:
[  321.269778]  ffff880100fc6680: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
[  321.269949]  ffff880100fc6700: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
[  321.270115] >ffff880100fc6780: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
[  321.270279]                                                     ^
[  321.270410]  ffff880100fc6800: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
[  321.270576]  ffff880100fc6880: fb fb fb fb fb fb fb fb fb fb fc fc fc fc fc fc
[  321.270740] ==================================================================
[  321.270903] Disabling lock debugging due to kernel taint

Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=101511
Fixes: 7dd4f6729f92 ("drm/i915: Async GPU relocation processing")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Tvrtko Ursulin <tvrtko.ursulin@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170620124321.1108-2-chris@chris-wilson.co.uk
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@linux.intel.com>

drm/i915: Enable Engine reset and recovery support

This feature is made available only from Gen8, for previous gen devices
driver uses legacy full gpu reset.

Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Signed-off-by: Tomas Elf <tomas.elf@intel.com>
Signed-off-by: Arun Siluvery <arun.siluvery@linux.intel.com>
Signed-off-by: Michel Thierry <michel.thierry@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170615201828.23144-10-michel.thierry@intel.com
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: http://patchwork.freedesktop.org/patch/msgid/20170620095751.13127-10-chris@chris-wilson.co.uk

drm/i915/selftests: reset engine self tests

Check that we can reset specific engines, also check the fallback to
full reset if something didn't work.

v2: rebase.
v3: use RESET_ENGINE_IN_PROGRESS flag.
v4: use I915_RESET_ENGINE flag.

Signed-off-by: Michel Thierry <michel.thierry@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170615201828.23144-12-michel.thierry@intel.com
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: http://patchwork.freedesktop.org/patch/msgid/20170620095751.13127-9-chris@chris-wilson.co.uk

drm/i915: Export per-engine reset count info to debugfs

A new variable is added to export the reset counts to debugfs, this
includes full gpu reset and engine reset count. This is useful for tests
where they are expected to trigger reset; these counts are checked before
and after the test to ensure the same.

v2: Include reset engine count in i915_engine_info too (Chris).

Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Signed-off-by: Arun Siluvery <arun.siluvery@linux.intel.com>
Signed-off-by: Michel Thierry <michel.thierry@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170615201828.23144-8-michel.thierry@intel.com
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: http://patchwork.freedesktop.org/patch/msgid/20170620095751.13127-8-chris@chris-wilson.co.uk

drm/i915: Add engine reset count to error state

Driver maintains count of how many times a given engine is reset, useful to
capture this in error state also. It gives an idea of how engine is coping
up with the workloads it is executing before this error state.

A follow-up patch will provide this information in debugfs.

v2: s/engine_reset/reset_engine/ (Chris)
    Define count as unsigned int (Tvrtko)

Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Signed-off-by: Arun Siluvery <arun.siluvery@linux.intel.com>
Signed-off-by: Michel Thierry <michel.thierry@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170615201828.23144-7-michel.thierry@intel.com
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: http://patchwork.freedesktop.org/patch/msgid/20170620095751.13127-7-chris@chris-wilson.co.uk

drm/i915: Add support for per engine reset recovery

This change implements support for per-engine reset as an initial, less
intrusive hang recovery option to be attempted before falling back to the
legacy full GPU reset recovery mode if necessary. This is only supported
from Gen8 onwards.

Hangchecker determines which engines are hung and invokes error handler to
recover from it. Error handler schedules recovery for each of those engines
that are hung. The recovery procedure is as follows,
 - identifies the request that caused the hang and it is dropped
 - force engine to idle: this is done by issuing a reset request
 - reset the engine
 - re-init the engine to resume submissions.

If engine reset fails then we fall back to heavy weight full gpu reset
which resets all engines and reinitiazes complete state of HW and SW.

v2: Rebase.
v3: s/*engine_reset*/*reset_engine*/; freeze engine and irqs before
calling i915_gem_reset_engine (Chris).
v4: Rebase, modify i915_gem_reset_prepare to use a ring mask and
reuse the function for reset_engine.
v5: intel_reset_engine_start/cancel instead of request/unrequest_reset.
v6: Clean up reset_engine function to not require mutex, i.e. no need to call
revoke/restore_fences and _retire_requests (Chris).
v7: Remove leftovers from v5, i.e. no need to disable irq, hold
forcewake or wakeup the handoff bit (Chris).
v8: engine_retire_requests should be (and it was) static; explain that
we have to re-init the engine after reset, which is why the init_hw call
is needed; check reset-in-progress flag (Chris).
v9: Rebase, include code to pass the active request to gem_reset_engine
(as it is already done in full reset). Remove unnecessary
intel_reset_engine_start/cancel, these are executed as part of the
reset.
v10: Rebase, use the right I915_RESET_ENGINE flag.
v11: Fixup to call reset_finish_engine even on error.

Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Signed-off-by: Tomas Elf <tomas.elf@intel.com>
Signed-off-by: Arun Siluvery <arun.siluvery@linux.intel.com>
Signed-off-by: Michel Thierry <michel.thierry@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170615201828.23144-6-michel.thierry@intel.com
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: http://patchwork.freedesktop.org/patch/msgid/20170620095751.13127-6-chris@chris-wilson.co.uk

drm/i915: Modify error handler for per engine hang recovery

This is a preparatory patch which modifies error handler to do per engine
hang recovery. The actual patch which implements this sequence follows
later in the series. The aim is to prepare existing recovery function to
adapt to this new function where applicable (which fails at this point
because core implementation is lacking) and continue recovery using legacy
full gpu reset.

A helper function is also added to query the availability of engine
reset. A subsequent patch will add the capability to query which type
of reset is present (engine -> full -> no-reset) via the get-param
ioctl.

It has been decided that the error events that are used to notify user of
reset will only be sent in case if full chip reset. In case of just
single (or multiple) engine resets, userspace won't be notified by these
events.

Note that this implementation of engine reset is for i915 directly
submitting to the ELSP, where the driver manages the hang detection,
recovery and resubmission. With GuC submission these tasks are shared
between driver and firmware; i915 will still responsible for detecting a
hang, and when it does it will have to request GuC to reset that Engine and
remind the firmware about the outstanding submissions. This will be
added in different patch.

v2: rebase, advertise engine reset availability in platform definition,
add note about GuC submission.
v3: s/*engine_reset*/*reset_engine*/. (Chris)
Handle reset as 2 level resets, by first going to engine only and fall
backing to full/chip reset as needed, i.e. reset_engine will need the
struct_mutex.
v4: Pass the engine mask to i915_reset. (Chris)
v5: Rebase, update selftests.
v6: Rebase, prepare for mutex-less reset engine.
v7: Pass reset_engine mask as a function parameter, and iterate over the
engine mask for reset_engine. (Chris)
v8: Use i915.reset >=2 in has_reset_engine; remove redundant reset
logging; add a reset-engine-in-progress flag to prevent concurrent
resets, and avoid dual purposing of reset-backoff. (Chris)
v9: Support reset of different engines in parallel (Chris)
v10: Handle reset-engine flag locking better (Chris)
v11: Squash in reporting of per-engine-reset availability.

Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Signed-off-by: Ian Lister <ian.lister@intel.com>
Signed-off-by: Tomas Elf <tomas.elf@intel.com>
Signed-off-by: Arun Siluvery <arun.siluvery@linux.intel.com>
Signed-off-by: Michel Thierry <michel.thierry@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170615201828.23144-4-michel.thierry@intel.com
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: http://patchwork.freedesktop.org/patch/msgid/20170620095751.13127-5-chris@chris-wilson.co.uk

drm/i915: Update i915.reset to handle engine resets

In preparation for engine reset work update this parameter to handle more
than one type of reset. Default at the moment is still full gpu reset.

Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Signed-off-by: Arun Siluvery <arun.siluvery@linux.intel.com>
Signed-off-by: Michel Thierry <michel.thierry@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170615201828.23144-3-michel.thierry@intel.com
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: http://patchwork.freedesktop.org/patch/msgid/20170620095751.13127-4-chris@chris-wilson.co.uk

drm/i915: Look for active requests earlier in the reset path

And store the active request so that we only search for it once.

v2: Check for request completion inside _prepare_engine, don't use
ECANCELED, remove unnecessary null checks (Chris).

v3: Capture active requests during reset_prepare and store it the
engine hangcheck obj.

v4: Rename commit, change i915_gem_reset_request to just confirm the
active_request is still incomplete, instead of engine_stalled (Chris).

v5: With style; pass the active request to gem_reset_engine, keep single
return in reset_prepare_engine (Chris).

v6: Moved before reset-engine code appears (Chris)

Suggested-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk> (v5)
Signed-off-by: Michel Thierry <michel.thierry@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170615201828.23144-2-michel.thierry@intel.com
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: http://patchwork.freedesktop.org/patch/msgid/20170620095751.13127-3-chris@chris-wilson.co.uk

drm/i915: Wait for concurrent global resets to complete

If we enter i915_handle_error() a second time and a global reset is
already in progress, we can simply wait for completion of the first
reset. Currently we exit early prior to the actual reset being
performed -- the worst of both worlds!

v2: Plug into the existing reset_queue, and remember that kselftests is
playing games with I915_RESET_BACKOFF to prevent hangcheck from screwing
up.
v3: Rename to i915_reset_device to fit in better with i915_reset_engine

Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Cc: Michel Thierry <michel.thierry@intel.com>
Reviewed-by: Michel Thierry <michel.thierry@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170620095751.13127-2-chris@chris-wilson.co.uk

drm/i915: Enable rcu-only context lookups

Whilst the contents of the context is still protected by the big
struct_mutex, this is not much of an improvement. It is just one tiny
step towards reducing our BKL.

Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170620110547.15947-3-chris@chris-wilson.co.uk

drm/i915: Allow contexts to be unreferenced locklessly

If we move the actual cleanup of the context to a worker, we can allow
the final free to be called from any context and avoid undue latency in
the caller.

v2: Negotiate handling the delayed contexts free by flushing the
workqueue before calling i915_gem_context_fini() and performing the final
free of the kernel context directly
v3: Flush deferred frees before new context allocations

Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170620110547.15947-2-chris@chris-wilson.co.uk

drm/i915: Group all the global context information together

Create a substruct to hold all the global context state under
drm_i915_private.

Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170620110547.15947-1-chris@chris-wilson.co.uk

drm/i915: Do not re-calculate num_rings locally

Since bb8f0f5abdd7 ("drm/i915: Split intel_engine allocation
and initialisation") intel_info->num_rings is set early in the
load sequence and so available to be used direclty in the 2nd
load phase.

Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: http://patchwork.freedesktop.org/patch/msgid/20170616130339.23015-1-tvrtko.ursulin@linux.intel.com

drm/i915: Simplify intel_engines_init

We do not want to carry on over missing constructors and don't
need a duplicated engine mask checking which is already done
in the setup phase.

Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>

drm/i915/cnl: Fix RMW on ddi vswing sequence.

Paulo noticed that we were missing few bits clear
before writing values back to the register on
these RMW MMIO operations.

v2: Remove "POST_" from CURSOR_COEFF_MASK. (Paulo).
v3: Remove unnecessary braces. (Jani).

Fixes: cf54ca8bc567 ("drm/i915/cnl: Implement voltage swing sequence.")
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: Manasi Navare <manasi.d.navare@intel.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1497897572-22520-1-git-send-email-rodrigo.vivi@intel.com

drm/i915: Make intel_digital_port_connected() work for any port

Add the missing port A handling to intel_digital_port_connected()
and also separate SPT from the CPT/LPT code a bit.

Cc: Manasi Navare <manasi.d.navare@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170615171252.11921-1-ville.syrjala@linux.intel.com
Reviewed-by: Manasi Navare <manasi.d.navare@intel.com>

drm/i915: Update DRIVER_DATE to 20170619

Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

drm/i915/cfl: Introduce Coffee Lake workarounds.

Coffee Lake inherit most of Kabylake production
workarounds.

v2: Fix typo on commit message and remove
    WaDisableKillLogic and GEN9_DISABLE_OCL_OOB_SUPPRESS_LOGIC,
    since as Mika pointed out they shouldn't be here for cfl
    according to BSpec.

Cc: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1497653398-15722-1-git-send-email-rodrigo.vivi@intel.com

drm/i915: Store 9 bits of PCI Device ID for platforms with a LP PCH

Although we use 9 bits of Device ID for identifying PCH, only 8 bits are
stored in dev_priv->pch_id. This makes HAS_PCH_CNP_LP() and
HAS_PCH_SPT_LP() incorrect. Fix this by storing all the 9 bits for the
platforms with LP PCH.

v2: Drop PCH_LPT_LP change (Imre)

Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Imre Deak <imre.deak@intel.com>
Fixes: commit ec7e0bb35f8d ("drm/i915/cnp: Add PCI ID for Cannonpoint LP PCH")
Reported-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1497641774-29104-1-git-send-email-dhinakaran.pandiyan@intel.com

drm/i915: Stash a pointer to the obj's resv in the vma

During execbuf, a mandatory step is that we add this request (this
fence) to each object's reservation_object. Inside execbuf, we track the
vma, and to add the fence to the reservation_object then means having to
first chase the obj, incurring another cache miss. We can reduce the
 number of cache misses by stashing a pointer to the reservation_object
in the vma itself.

Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170616140525.6394-1-chris@chris-wilson.co.uk

drm/i915: Async GPU relocation processing

If the user requires patching of their batch or auxiliary buffers, we
currently make the alterations on the cpu. If they are active on the GPU
at the time, we wait under the struct_mutex for them to finish executing
before we rewrite the contents. This happens if shared relocation trees
are used between different contexts with separate address space (and the
buffers then have different addresses in each), the 3D state will need
to be adjusted between execution on each context. However, we don't need
to use the CPU to do the relocation patching, as we could queue commands
to the GPU to perform it and use fences to serialise the operation with
the current activity and future - so the operation on the GPU appears
just as atomic as performing it immediately. Performing the relocation
rewrites on the GPU is not free, in terms of pure throughput, the number
of relocations/s is about halved - but more importantly so is the time
under the struct_mutex.

v2: Break out the request/batch allocation for clearer error flow.
v3: A few asserts to ensure rq ordering is maintained

Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>

drm/i915: Allow execbuffer to use the first object as the batch

Currently, the last object in the execlist is the always the batch.
However, when building the batch buffer we often know the batch object
first and if we can use the first slot in the execlist we can emit
relocation instructions relative to it immediately and avoid a separate
pass to adjust the relocations to point to the last execlist slot.

Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>

drm/i915: Wait upon userptr get-user-pages within execbuffer

This simply hides the EAGAIN caused by userptr when userspace causes
resource contention. However, it is quite beneficial with highly
contended userptr users as we avoid repeating the setup costs and
kernel-user context switches.

Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Michał Winiarski <michal.winiarski@intel.com>

drm/i915: First try the previous execbuffer location

When choosing a slot for an execbuffer, we ideally want to use the same
address as last time (so that we don't have to rebind it) and the same
address as expected by the user (so that we don't have to fixup any
relocations pointing to it). If we first try to bind the incoming
execbuffer->offset from the user, or the currently bound offset that
should hopefully achieve the goal of avoiding the rebind cost and the
relocation penalty. However, if the object is not currently bound there
we don't want to arbitrarily unbind an object in our chosen position and
so choose to rebind/relocate the incoming object instead. After we
report the new position back to the user, on the next pass the
relocations should have settled down.

Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Joonas Lahtinen <joonas.lahtien@linux.intel.com>

drm/i915: Store a persistent reference for an object in the execbuffer cache

If we take a reference to the object/vma when it is first used in an
execbuf, we can keep that reference until the object's file-local handle
is closed. Thereby saving a frequent ref/unref pair.

Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>

drm/i915: Eliminate lots of iterations over the execobjects array

The major scaling bottleneck in execbuffer is the processing of the
execobjects. Creating an auxiliary list is inefficient when compared to
using the execobject array we already have allocated.

Reservation is then split into phases. As we lookup up the VMA, we
try and bind it back into active location. Only if that fails, do we add
it to the unbound list for phase 2. In phase 2, we try and add all those
objects that could not fit into their previous location, with fallback
to retrying all objects and evicting the VM in case of severe
fragmentation. (This is the same as before, except that phase 1 is now
done inline with looking up the VMA to avoid an iteration over the
execobject array. In the ideal case, we eliminate the separate reservation
phase). During the reservation phase, we only evict from the VM between
passes (rather than currently as we try to fit every new VMA). In
testing with Unreal Engine's Atlantis demo which stresses the eviction
logic on gen7 class hardware, this speed up the framerate by a factor of
2.

The second loop amalgamation is between move_to_gpu and move_to_active.
As we always submit the request, even if incomplete, we can use the
current request to track active VMA as we perform the flushes and
synchronisation required.

The next big advancement is to avoid copying back to the user any
execobjects and relocations that are not changed.

v2: Add a Theory of Operation spiel.
v3: Fall back to slow relocations in preparation for flushing userptrs.
v4: Document struct members, factor out eb_validate_vma(), add a few
more comments to explain some magic and hide other magic behind macros.

Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>

drm/i915: Disable EXEC_OBJECT_ASYNC when doing relocations

If we write a relocation into the buffer, we require our own implicit
synchronisation added after the start of the execbuf, outside of the
user's control. As we may end up clflushing, or doing the patch itself
on the GPU, asynchronously we need to look at the implicit serialisation
on obj->resv and hence need to disable EXEC_OBJECT_ASYNC for this
object.

If the user does trigger a stall for relocations, we make sure the stall
is complete enough so that the batch is not submitted before we complete
those relocations.

Fixes: 77ae9957897d ("drm/i915: Enable userspace to opt-out of implicit fencing")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Jason Ekstrand <jason@jlekstrand.net>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>

drm/i915: Pass vma to relocate entry

We can simplify our tracking of pending writes in an execbuf to the
single bit in the vma->exec_entry->flags, but that requires the
relocation function knowing the object's vma. Pass it along.

Note we have only been using a single bit to track flushing since

commit cc889e0f6ce6a63c62db17d702ecfed86d58083f
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date:   Wed Jun 13 20:45:19 2012 +0200

    drm/i915: disable flushing_list/gpu_write_list

unconditionally flushed all render caches before the breadcrumb and

commit 6ac42f4148bc27e5ffd18a9ab0eac57f58822af4
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date:   Sat Jul 21 12:25:01 2012 +0200

    drm/i915: Replace the complex flushing logic with simple invalidate/flush all

did away with the explicit GPU domain tracking. This was then codified
into the ABI with NO_RELOC in

commit ed5982e6ce5f106abcbf071f80730db344a6da42
Author: Daniel Vetter <daniel.vetter@ffwll.ch> # Oi! Patch stealer!
Date:   Thu Jan 17 22:23:36 2013 +0100

    drm/i915: Allow userspace to hint that the relocations were known

Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>

drm/i915: Store a direct lookup from object handle to vma

The advent of full-ppgtt lead to an extra indirection between the object
and its binding. That extra indirection has a noticeable impact on how
fast we can convert from the user handles to our internal vma for
execbuffer. In order to bypass the extra indirection, we use a
resizable hashtable to jump from the object to the per-ctx vma.
rhashtable was considered but we don't need the online resizing feature
and the extra complexity proved to undermine its usefulness. Instead, we
simply reallocate the hastable on demand in a background task and
serialize it before iterating.

In non-full-ppgtt modes, multiple files and multiple contexts can share
the same vma. This leads to having multiple possible handle->vma links,
so we only use the first to establish the fast path. The majority of
buffers are not shared and so we should still be able to realise
speedups with multiple clients.

v2: Prettier names, more magic.
v3: Many style tweaks, most notably hiding the misuse of execobj[].rsvd2

Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>

drm/i915: Fix retrieval of hangcheck stats

The default context is always supported (as it contains the global
hangcheck stats) and the contexts for hangcheck are not limited
to any ring.

This was dropped in 2013 because it was supposed to have been included
with Ben's full-ppgtt patch set. It never landed and the bug remains.

References: https://bugs.freedesktop.org/show_bug.cgi?id=65845
Link: http://patchwork.freedesktop.org/patch/msgid/1372175222-27622-1-git-send-email-mika.kuoppala@intel.com
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170616132849.29597-1-chris@chris-wilson.co.uk

drm/i915: Store i915_gem_object_is_coherent() as a bit next to cache-dirty

For ease of use (i.e. avoiding a few checks and function calls), store
the object's cache coherency next to the cache is dirty bit.

Specifically this patch aims to reduce the frequency of no-op calls to
i915_gem_object_clflush() to counter-act the increase of such calls for
GPU only objects in the previous patch.

v2: Replace cache_dirty & ~cache_coherent with cache_dirty &&
!cache_coherent as gcc generates much better code for the latter
(Tvrtko)

Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Dongwon Kim <dongwon.kim@intel.com>
Cc: Matt Roper <matthew.d.roper@intel.com>
Tested-by: Dongwon Kim <dongwon.kim@intel.com>
Cc: Tvrtko Ursulin <tvrtko.ursulin@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170616105455.16977-1-chris@chris-wilson.co.uk
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>

drm/i915: Mark CPU cache as dirty on every transition for CPU writes

Currently, we only mark the CPU cache as dirty if we skip a clflush.
This leads to some confusion where we have to ask if the object is in
the write domain or missed a clflush. If we always mark the cache as
dirty, this becomes a much simply question to answer.

The goal remains to do as few clflushes as required and to do them as
late as possible, in the hope of deferring the work to a kthread and not
block the caller (e.g. execbuf, flips).

v2: Always call clflush before GPU execution when the cache_dirty flag
is set. This may cause some extra work on llc systems that migrate dirty
buffers back and forth - but we do try to limit that by only setting
cache_dirty at the end of the gpu sequence.

v3: Always mark the cache as dirty upon a level change, as we need to
invalidate any stale cachelines due to external writes.

Reported-by: Dongwon Kim <dongwon.kim@intel.com>
Fixes: a6a7cc4b7db6 ("drm/i915: Always flush the dirty CPU cache when pinning the scanout")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Dongwon Kim <dongwon.kim@intel.com>
Cc: Matt Roper <matthew.d.roper@intel.com>
Tested-by: Dongwon Kim <dongwon.kim@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170615123850.26843-1-chris@chris-wilson.co.uk
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>

drm/i915: Make i915_vma_destroy() static

i915_vma_destroy() is now not used outside of i915_vma.c so we can
remove the export and make the function static.

Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170616123508.12673-1-chris@chris-wilson.co.uk
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@linux.intel.com>

drm/i915: Actually attach the tv_format property to the SDVO connector

Attach the tv_format property to the SDVO connector instead of passing
a '0' in place of the pointer to the property. This got broken when
the SDVO connector properties were converted to atomic.

We can thank sparse for catching this:
drivers/gpu/drm/i915/intel_sdvo.c:2742:75: warning: Using plain integer as NULL pointer

Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Fixes: 630d30a4ee27 ("drm/i915: Convert intel_sdvo connector properties to atomic.")
Link: http://patchwork.freedesktop.org/patch/msgid/20170615172308.10121-1-ville.syrjala@linux.intel.com
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>

Merge tag 'gvt-next-2017-06-08' of https://github.com/01org/gvt-linux into drm-intel-next-queued

gvt-next-2017-06-08

First gvt-next pull for 4.13:
- optimization for per-VM mmio save/restore (Changbin)
- optimization for mmio hash table (Changbin)
- scheduler optimization with event (Ping)
- vGPU reset refinement (Fred)
- other misc refactor and cleanups, etc.

Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170608093547.bjgs436e3iokrzdm@zhen-hp.sh.intel.com

Revert "drm/i915/skl: New ddb allocation algorithm"

This reverts commit bb9d85f6e9de8fef5236c076530eab67a2f2431b.

New ddb allocation algorithm is a show stopper on my SKL system.

Besides not be able to get external DP 4k@60 (through USB type C),
It fully hang my screen when unplugging the USB type C.

Bugzilla: https://patchwork.freedesktop.org/patch/161571/
Fixes: bb9d85f6e9de ("drm/i915/skl: New ddb allocation algorithm")
Cc: Mahesh Kumar <mahesh1.kumar@intel.com>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1497376350-3400-1-git-send-email-rodrigo.vivi@intel.com

drm/i915/glk: Add cold boot sequence for GLK DSI

As per BSEPC, if device ready bit is '0' in enable IO sequence
then its a cold boot/reset scenario eg: S3/S4 resume. If cold boot
scenario detected in enable IO, then prepare port immediately.
In normal boot scenario, prepare port after glk_dsi_device_ready().
Without cold boot sequence enabled, features like S3/S4 doesn't work.

Signed-off-by: Madhav Chauhan <madhav.chauhan@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1497340095-5877-2-git-send-email-madhav.chauhan@intel.com

drm/i915/glk: Split GLK DSI device ready functionality

This patch divides glk_dsi_device_ready() function into
two part. First part will program LP wake and MIPI DSI mode
to MIPI_CTRL reg using newly defined function glk_dsi_enable_io().
glk_dsi_enable_io() will be called from intel_dsi_pre_enable.
Second part will do remaining device ready activities using
the existing function glk_dsi_device_ready().

Signed-off-by: Madhav Chauhan <madhav.chauhan@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1497340095-5877-1-git-send-email-madhav.chauhan@intel.com

drm/i915: Don't enable backlight at setup time.

Maarten and Ville noticed that we are enabling backlight via DP aux very
early in the modeset_init path via the intel_dp_aux_setup_backlight()
function, since commit e7156c833903 ("drm/i915: Add Backlight Control using
DPCD for eDP connectors (v9)"). Looks like all we need to do during
_setup_backlight() is read the current brightness state instead of
modifying it.

v2: Rewrote commit message.

Cc: Ville Syrjala <ville.syrjala@linux.intel.com>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Yetunde Adebisi <yetundex.adebisi@intel.com>
Signed-off-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Acked-by: Jani Nikula <jani.nikula@intel.com>
Tested-by: Puthikorn Voravootivat <puthik@chromium.org>
Fixes: e7156c833903 ("drm/i915: Add Backlight Control using DPCD for eDP connectors (v9)")
Link: http://patchwork.freedesktop.org/patch/msgid/1497384239-2965-1-git-send-email-dhinakaran.pandiyan@intel.com
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>

drm/i915/cnl: make function cnl_ddi_dp_set_dpll_hw_state static

The function cnl_ddi_dp_set_dpll_hw_state does not need to be in global
scope, so make it static.

Cleans up sparse warning:
"symbol 'cnl_ddi_dp_set_dpll_hw_state' was not declared. Should it
 be static?"

Signed-off-by: Colin Ian King <colin.king@canonical.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170613134751.29196-1-colin.king@canonical.com
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>

drm/i915: Remove pipe A quirk remnants

With 830 the only thing needing pipe quirks, we can just drop the quirk
defines and replace the checks with IS_I830() checks.

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170601143619.27840-8-ville.syrjala@linux.intel.com
Acked-by: Chris Wilson <chris@chris-wilson.co.uk>
Acked-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>

drm/i915: Drop pipe A quirk for Thinkapd T60

The pipe A force quirk shouldn't needed except on 830. So let's nuke it
for the IBM Thinkpad T60 945 machines. This quirk pre-dates
KMS so it's usefulness is doubtful at best now.

The original bug report [1] describes the symptoms as "system hang on
closing T60 panel lid", and we already dropped a similar quirk for
another 945 machine in
commit 736a69ca8c99 ("drm/i915: Drop PIPE-A quirk for 945GSE HP Mini")
so I'm hopeful we can drop this one as well.

The quirk was added into xf86-video-intel in
commit 08903abe4dc0 ("Add pipe a force enable quirk for Lenovo T60")

[1] https://bugs.freedesktop.org/show_bug.cgi?id=16494

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170601143619.27840-7-ville.syrjala@linux.intel.com
Acked-by: Chris Wilson <chris@chris-wilson.co.uk>
Acked-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>

drm/i915: Drop pipe A quirk for Toshiba Protege R205-S209

The pipe A force quirk shouldn't needed except on 830. So let's nuke it
for the Toshiba Protege R-205/S-209 945 machines. This quirk pre-dates
KMS so it's usefulness is doubtful at best now.

Unfortunately the original bug report [1] isn't very helpful since it
doesn't describe the symptoms. And the commit message in xf86-video-intel
commit ecdb5963ef68 ("Add pipe A force enable quirk for Toshiba Portege R205-S209")
is not much help either.

However, if we assume the problem was the typical "closing the lid
hangs the box" type of thing, we already nuked the quirk for another
945 machine in
commit 736a69ca8c99 ("drm/i915: Drop PIPE-A quirk for 945GSE HP Mini")
and so I hope we can drop this one as well.

[1] https://bugs.freedesktop.org/show_bug.cgi?id=14944

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170601143619.27840-6-ville.syrjala@linux.intel.com
Acked-by: Chris Wilson <chris@chris-wilson.co.uk>
Acked-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>

drm/i915: Add i830 "pipes power well"

830 more or less requires both pipes and DPLLs to remain on as long
as either pipe is needed. However, when neither pipe is actually needed,
we can save a bit of power by turning everything off. To do that we add
a new "power well" that turns both pipes and DPLLs on and off in the
right order. Seems to save ~50mW on my Fujitsu-Siemens Lifebook S6010.

This also avoids having to abuse the load detection to force pipe A on
at init time. That was never very robust, and it only worked for one
pipe, whereas 830 really needs both pipes enabled. As a bonus the 830
pipe quirk is now a bit more isolated from the rest of the mode setting
infrastructure, which should mean that it's much less likely someone
will accidentally break it in the future. The extra cost is of course
slight code duplication, but that seems like a worthwile tradeoff here.

v2; s/BIT/BIT_ULL/

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170601143619.27840-5-ville.syrjala@linux.intel.com
Acked-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>

drm/i915: Use a loop for the "three times for luck" DPLL procedure

The magic "enable the  DPLL three times" sequence feels like it
deserves a loop.

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170601143619.27840-4-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>

drm/i915: Plumb the correct acquire ctx into intel_crtc_disable_noatomic()

If intel_crtc_disable_noatomic() were to ever get called during resume
we'd end up deadlocking since resume has its own acqcuire_ctx but
intel_crtc_disable_noatomic() still tries to use the
mode_config.acquire_ctx. Pass down the correct acquire ctx from the top.

Cc: stable@vger.kernel.org
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Fixes: e2c8b8701e2d ("drm/i915: Use atomic helpers for suspend, v2.")
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170601143619.27840-3-ville.syrjala@linux.intel.com
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>

drm/i915: Fix deadlock witha the pipe A quirk during resume

Pass down the correct acquire context to the pipe A quirk load detect
hack during display resume. Avoids deadlocking the entire thing.

Cc: stable@vger.kernel.org
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Fixes: e2c8b8701e2d ("drm/i915: Use atomic helpers for suspend, v2.")
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170601143619.27840-2-ville.syrjala@linux.intel.com
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>

drm/i915: Split vma exec_link/evict_link

Currently the vma has one link member that is used for both holding its
place in the execbuf reservation list, and in any eviction list. This
dual property is quite tricky and error prone.

Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170615081435.17699-3-chris@chris-wilson.co.uk

drm/i915: Use vma->exec_entry as our double-entry placeholder

This has the benefit of not requiring us to manipulate the
vma->exec_link list when tearing down the execbuffer, and is a
marginally cheaper test to detect the user error.

Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170615081435.17699-2-chris@chris-wilson.co.uk

drm/i915: Amalgamate execbuffer parameter structures

Combine the two slightly overlapping parameter structures we pass around
the execbuffer routines into one.

Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170615081435.17699-1-chris@chris-wilson.co.uk

drm/i915/perf: add GLK support

Add OA support for Geminilake (pretty much identical to Broxton), and
also add the associated OA configurations.

Signed-off-by: Lionel Landwerlin <lionel.g.landwerlin@intel.com>
Reviewed-by: Matthew Auld <matthew.auld@intel.com>
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Link: http://patchwork.freedesktop.org/patch/msgid/20170613112309.4088-2-lionel.g.landwerlin@intel.com

drm/i915/perf: add KBL support

Add OA support for Kabylake (pretty much identical to Skylake), and
also add the associated OA configurations.

Signed-off-by: Lionel Landwerlin <lionel.g.landwerlin@intel.com>
Reviewed-by: Matthew Auld <matthew.auld@intel.com>
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>

drm/i915: add KBL GT2/GT3 check macros

Add macros to detect GT2/GT3 skus so we can apply the proper OA
configuration later.

Signed-off-by: Lionel Landwerlin <lionel.g.landwerlin@intel.com>
Reviewed-by: Matthew Auld <matthew.auld@intel.com>
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>