Staging: DST: optimize bio allocation.

Use bio prepend feature as suggested by Jens Axboe.

Signed-off-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Staging: dst: kconfig update.

On Wed, Jan 14, 2009 at 02:05:33AM +0300, Evgeniy Polyakov (zbr@ioremap.net) wrote:
> --- /dev/null
> +++ b/drivers/staging/dst/Kconfig
> @@ -0,0 +1,71 @@
> +config DST
> + tristate "Distributed storage"
> + depends on NET && CRYPTO && SYSFS
> + select CONNECTOR
> + select LIBCRC32C

Above is not needed.

Signed-off-by: Evgeniy Polyakov <zbr@ioremap.net>
Cc: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Staging: dst: kconfig and makefile changes.

Signed-off-by: Evgeniy Polaykov <zbr@ioremap.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

staging: dst: replace bus_id with dev_set_name

bus_id is going away, use the dev_set_name() function instead.

Cc: Kay Sievers <kay.sievers@vrfy.org>
Cc: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Staging: dst: crypto processing.

DST may fully encrypt the data channel in case of untrusted channel and implement
strong checksum of the transferred data. It is possible to configure algorithms
and crypto keys, they should match on both sides of the network channel.
Crypto processing does not introduce noticeble performance overhead, since DST
uses configurable pool of threads to perform crypto processing.

This patch introduces crypto processing helpers and crypto engine initialization:
glueing with the crypto layer, allocation and initialization of the crypto
processing thread pool, allocation of the cached pages, which are used to temporary
encrypt data into, since it is forbidden to encrypt data in-place, since pages
are used by the higher layers.

Signed-off-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Staging: dst: transactions.

DST uses transaction model, when each store has to be explicitly acked
from the remote node to be considered as successfully written. There
may be lots of in-flight transactions. When remote host does not ack
the transaction it will be resent predefined number of times with specified
timeouts between them. All those parameters are configurable. Transactions
are marked as failed after all resends completed unsuccessfully, having
long enough resend timeout and/or large number of resends allows not to
return error to the higher (FS usually) layer in case of short network
problems or remote node outages. In case of network RAID setup this means
that storage will not degrade until transactions are marked as failed, and
thus will not force checksum recalculation and data rebuild. In case of
connection failure DST will try to reconnect to the remote node automatically.
DST sends ping commands at idle time to detect if remote node is alive.

Because of transactional model it is possible to use zero-copy sending
without worry of data corruption (which in turn could be detected by the
strong checksums though).

Transactions are handled in this patch: allocation/freeing/completion,
scanning for stall and to-be-resent transactions and overall management
of the storing tree.

Signed-off-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Staging: dst: thread pool.

Kernel currently does not allow to queue work into some entity which
will perform it in the process context and have simple way to extend
number of worker and work with them not as separate objects, but with
pool as a whole. So thread pool model was implemented in the DST.

Thread pool abstraction allows to schedule a work to be performed
on behalf of kernel thread. One does not operate with threads itself,
instead user provides setup and cleanup callbacks for thread pool itself,
and action and cleanup callbacks for each submitted work.

Each worker has private data initialized at creation time and data,
provided by user at scheduling time.

When action is being performed, thread can not be used by other users,
instead they will sleep until there is free thread to pick their work.

Thread pool is used for crypto processing of incoming and outgoing IO
requests to reduce the overall overhead.

Signed-off-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Staging: dst: export node.

This patch introduces remote (export) node machinery: initialization
address/port (and other socket parameters), export block device (can be
another DST storage for example or local device like /dev/sda1), local
IO processing engine (BIO state machines, receiving/submitting logic).
Network management for the export node like accepting new client, scheduling
its command processing thread, receiving/sending IO requests, all are placed
here.

Signed-off-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Staging: dst: network state machine.

Each DST device contains of two nodes: local and remote (called also as export node).
This patch contains local node processing engine: network state storage,
socket processing loops and state machine, socket polling machinery, reconnection
logic, send/receive basic helpers, related IO commands and so on.

Signed-off-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Staging: dst: core files.

This patch contains DST core files, which introduce
block layer, connector and sysfs registration glue and main headers.

Connector is used for the configuration of the node (its type, address,
device name and so on). Sysfs provides bits of information about running
devices in the following format:

+/*
+ * DST sysfs tree for device called 'storage':
+ *
+ * /sys/bus/dst/devices/storage/
+ * /sys/bus/dst/devices/storage/type : 192.168.4.80:1025
+ * /sys/bus/dst/devices/storage/size : 800
+ * /sys/bus/dst/devices/storage/name : storage
+ */

DST header contains structure definitions and protocol command description.

Signed-off-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Staging: frontier: Remove unused components of the alphatrack/tranzport sysfs interface.

Signed-off-by: David Täht <d@teklibre.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Staging: frontier: Make checkpatch.pl happy with alphatrack.h

Signed-off-by: David Täht <d@teklibre.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Staging: frontier: Updated documentation

Signed-off-by: David Täht <d@teklibre.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Staging: frontier: removed now unused frontier_compat.h file

Signed-off-by: David Täht <d@teklibre.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
index 00450e6..0000000

Staging: frontier: Make checkpatch.pl much happier with alphatrack driver

Signed-off-by: David Täht <d@teklibre.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Staging: frontier: Make checkpatch.pl considerably happier with tranzport driver.

Signed-off-by: David Täht <d@teklibre.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Staging: rt2870: Removal of kernel_thread() API

Replacing the use of kernel_thread() with kthread_run().   But as
kthread_run() returned a task structure, as compared with
kernel_thread() returning a PID, it was found to be more efficient to
store the task structure pointer as a field data instead of PID
pointer.   On top of modifying the field to store task structure
pointer, the initialization of the field (assigned to
THREAD_PID_INIT_VALUE) was also found unnecessary - as no where it is
found to be used.

Signed-off-by: Peter Teoh <htmldeveloper@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Staging: rt2870: add Linksys WUSB600N device id

Updated usb device list to support Linksys WUSB600N wireless adapter

Signed-off-by: Josef Jiru <josef.jiru@gmx.net>

Staging: rt2860: Remove dependency on CFLAG RT2860

Removed the CFLAG RT2860 from Makefile and dependency on it in the driver code.

Signed-off-by: Mark Einon <mark.einon@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Staging: rt2860: Fix remaining build warnings

Fixed remaining four build warnings in drivers/staging/rt2860/:

drivers/staging/rt2860/common/mlme.c:900: warning: format ‘%d’ expects type ‘int’, but argument 2 has type ‘ULONG’
drivers/staging/rt2860/common/rtmp_init.c:2049: warning: ‘Value’ may be used uninitialized in this function
drivers/staging/rt2860/sta_ioctl.c:361: warning: ‘return’ with a value, in function returning void
drivers/staging/rt2860/sta_ioctl.c:2468: warning: ‘return’ with a value, in function returning void

Signed-off-by: Mark Einon <mark.einon@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Staging: rt2860: Ported v1.7.1.1 changes into v1.8.0.0, becoming v1.8.1.1

Staging: rt2860: Ported v1.7.1.1 changes into v1.8.0.0, becoming v1.8.1.1

When RaLink released rt2860 v1.7.0.0, it lacked proper support for both WEP
and WPA/WPA2 encryption. Either was possible, but the module had to be
compiled to support only one or the other, never both.

Since the EeePC was the most common device with this hardware (and these
users were complaining to RaLink that WPA/WPA2 encryption didn't work)
RaLink released a fix as an "eeepc-specific" version of this driver, v1.7.1.1

Unfortunately, when v1.8.0.0 was released, this WPA/WPA2 fix was never
included.

What complicates things further is that RaLink has no interest in
continuing work on this Linux driver for their hardware.

This commit ports the changes introduced in v1.7.1.1 into the v1.8.0.0
release, upgrading the kernel's module to v1.8.1.1

Signed-off-by: Adam McDaniel <adam@array.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Staging: rt2860: fix printk format warnings

Fix staging/rt28x0 printk format warnings:

linux-next-20090209/drivers/staging/rt2860/common/spectrum.c:1599: warning: format '%d' expects type 'int', but argument 3 has type 'long unsigned int'
linux-next-20090209/drivers/staging/rt2860/rt_linux.c:857: warning: format '%d' expects type 'int', but argument 3 has type 'long unsigned int'

linux-next-20090209/drivers/staging/rt2870/common/spectrum.c:1598: warning: format '%d' expects type 'int', but argument 3 has type 'long unsigned int'
linux-next-20090209/drivers/staging/rt2870/rt_linux.c:898: warning: format '%d' expects type 'int', but argument 3 has type 'long unsigned int'

Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Staging: rt2860: remove kernel version compatibility wrappers

The driver is in mainline now so there's no point in keeping the
kernel version compatibility wrappers around.

Signed-off-by: Pekka Enberg <penberg@cs.helsinki.fi>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Staging: rt2860,rt2870: Correct use of ! and &

IW_ENCODE_MODE is 0xF000 and thus !erq->flags & IW_ENCODE_MODE is always 0.
I assume that !(erq->flags & IW_ENCODE_MODE) was intended.

The semantic patch that makes this change is as follows:
(http://www.emn.fr/x-info/coccinelle/)

// <smpl>
@@ expression E; constant C; @@
(
  !E & !C
|
- !E & C
+ !(E & C)
)
// </smpl>

Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Staging: rtl8187se: fix \r\n line ends

Andrew pointed out that I forgot to convert some files to unix format
when adding them originally.  This patch runs dos2unix on the rtl8187se
files that needed them.

Reported-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Staging: rtl8187se: ! x & y problem in inactive code

Fix ! x & y problem in inactivated code

Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Staging: rtl8187se: fix build warnings

drivers/staging/rtl8187se/r8180_wx.c:1386: warning: initialization from incompatible pointer type
drivers/staging/rtl8187se/r8180_wx.c:1388: warning: initialization from incompatible pointer type

Signed-off-by: Herton Ronaldo Krzesinski <herton@mandriva.com.br>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Staging: rtl8187se: fix printk format warnings

Fix staging/rtl8187se printk format warnings:

drivers/staging/rtl8187se/ieee80211/ieee80211_wx.c:845: warning: format '%d' expects type 'int', but argument 2 has type 'size_t'
drivers/staging/rtl8187se/ieee80211/ieee80211_wx.c:852: warning: format '%d' expects type 'int', but argument 2 has type 'size_t'

Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Staging: Android: fix more printk formats

Fix more android ram_console printk format warnings:

drivers/staging/android/ram_console.c:238: warning: format '%d' expects type 'int', but argument 3 has type 'size_t'
drivers/staging/android/ram_console.c:238: warning: format '%d' expects type 'int', but argument 4 has type 'size_t'

Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Staging: android: ram_console: fix printk format warning

Fix android printk format warnings:

linux-next-20090209/drivers/staging/android/ram_console.c:228: warning: format '%d' expects type 'int', but argument 3 has type 'size_t'
linux-next-20090209/drivers/staging/android/ram_console.c:228: warning: format '%d' expects type 'int', but argument 4 has type 'size_t'
linux-next-20090209/drivers/staging/android/ram_console.c:326: warning: format '%x' expects type 'unsigned int', but argument 2 has type 'size_t'
linux-next-20090209/drivers/staging/android/ram_console.c:326: warning: format '%x' expects type 'unsigned int', but argument 3 has type 'size_t'

Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Staging: android: binder: fix printk format warnings

Fix printk format warnings in android binder:

drivers/staging/android/binder.c:2652: warning: format '%lx' expects type 'long unsigned int', but argument 7 has type 'pgprotval_t'
drivers/staging/android/binder.c:2659: warning: format '%lx' expects type 'long unsigned int', but argument 7 has type 'pgprotval_t'
drivers/staging/android/binder.c:2680: warning: format '%lx' expects type 'long unsigned int', but argument 7 has type 'pgprotval_t'

Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Staging: otus: remove old irqreturn_t definition

See commit bedd30d9 (genirq: make irqreturn_t an enum)

Signed-off-by: Alexander Beregalov <a.beregalov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Staging: otus: 80211core/amsdu.c: Fix Coding Style

Signed-off-by: Dragoslav Zaric <dragoslav.zaric.kd@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Staging: otus: ioctl.c: Fix Coding Style

I run make on ioctl.c file and I got two warnings:
drivers/staging/otus/ioctl.c: In function ¡usbdrv_wpa_ioctl¢:
drivers/staging/otus/ioctl.c:2269: warning: ISO C90 forbids mixed declarations and code
drivers/staging/otus/ioctl.c: In function ¡usbdrv_ioctl¢:
drivers/staging/otus/ioctl.c:2448: warning: ISO C90 forbids mixed declarations and code

From: Dragoslav Zaric <dragoslav.zaric.kd@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Staging: otus: fix mixed declarations

Fix otus ISO C90 warnings:

drivers/staging/otus/80211core/cmmsta.c:740: warning: ISO C90 forbids mixed declarations and code
drivers/staging/otus/80211core/coid.c:219: warning: ISO C90 forbids mixed declarations and code
drivers/staging/otus/80211core/coid.c:1437: warning: ISO C90 forbids mixed declarations and code
drivers/staging/otus/hal/hprw.c:33: warning: ISO C90 forbids mixed declarations and code
drivers/staging/otus/hal/hprw.c:53: warning: ISO C90 forbids mixed declarations and code
drivers/staging/otus/hal/hprw.c:82: warning: ISO C90 forbids mixed declarations and code
drivers/staging/otus/hal/hprw.c:163: warning: ISO C90 forbids mixed declarations and code
drivers/staging/otus/hal/hprw.c:219: warning: ISO C90 forbids mixed declarations and code
drivers/staging/otus/hal/hprw.c:831: warning: ISO C90 forbids mixed declarations and code
drivers/staging/otus/hal/hprw.c:896: warning: ISO C90 forbids mixed declarations and code
drivers/staging/otus/hal/hpmain.c:332: warning: ISO C90 forbids mixed declarations and code
drivers/staging/otus/hal/hpmain.c:1329: warning: ISO C90 forbids mixed declarations and code
drivers/staging/otus/hal/hpmain.c:1565: warning: ISO C90 forbids mixed declarations and code
drivers/staging/otus/hal/hpmain.c:1606: warning: ISO C90 forbids mixed declarations and code
drivers/staging/otus/hal/hpmain.c:1923: warning: ISO C90 forbids mixed declarations and code
drivers/staging/otus/hal/hpmain.c:1997: warning: ISO C90 forbids mixed declarations and code
drivers/staging/otus/hal/hpmain.c:2264: warning: ISO C90 forbids mixed declarations and code
drivers/staging/otus/hal/hpmain.c:2296: warning: ISO C90 forbids mixed declarations and code
drivers/staging/otus/hal/hpmain.c:2330: warning: ISO C90 forbids mixed declarations and code
drivers/staging/otus/hal/hpmain.c:2350: warning: ISO C90 forbids mixed declarations and code
drivers/staging/otus/hal/hpmain.c:2387: warning: ISO C90 forbids mixed declarations and code
drivers/staging/otus/hal/hpmain.c:2425: warning: ISO C90 forbids mixed declarations and code
drivers/staging/otus/hal/hpmain.c:4223: warning: ISO C90 forbids mixed declarations and code
drivers/staging/otus/hal/hpmain.c:4283: warning: ISO C90 forbids mixed declarations and code
drivers/staging/otus/hal/hpmain.c:4314: warning: ISO C90 forbids mixed declarations and code
drivers/staging/otus/hal/hpmain.c:4380: warning: ISO C90 forbids mixed declarations and code
drivers/staging/otus/hal/hpmain.c:4425: warning: ISO C90 forbids mixed declarations and code
drivers/staging/otus/hal/hpmain.c:4531: warning: ISO C90 forbids mixed declarations and code
drivers/staging/otus/hal/hpmain.c:4539: warning: ISO C90 forbids mixed declarations and code
drivers/staging/otus/hal/hpusb.c:69: warning: ISO C90 forbids mixed declarations and code
drivers/staging/otus/hal/hpusb.c:334: warning: ISO C90 forbids mixed declarations and code
drivers/staging/otus/hal/hpusb.c:580: warning: ISO C90 forbids mixed declarations and code
drivers/staging/otus/hal/hpreg.c:1774: warning: ISO C90 forbids mixed declarations and code
drivers/staging/otus/hal/hpreg.c:2478: warning: ISO C90 forbids mixed declarations and code
drivers/staging/otus/hal/hpani.c:61: warning: ISO C90 forbids mixed declarations and code
drivers/staging/otus/hal/hpani.c:80: warning: ISO C90 forbids mixed declarations and code
drivers/staging/otus/hal/hpani.c:145: warning: ISO C90 forbids mixed declarations and code
drivers/staging/otus/hal/hpani.c:352: warning: ISO C90 forbids mixed declarations and code
drivers/staging/otus/hal/hpani.c:393: warning: ISO C90 forbids mixed declarations and code
drivers/staging/otus/hal/hpani.c:472: warning: ISO C90 forbids mixed declarations and code
drivers/staging/otus/hal/hpani.c:517: warning: ISO C90 forbids mixed declarations and code
drivers/staging/otus/hal/hpani.c:592: warning: ISO C90 forbids mixed declarations and code
drivers/staging/otus/hal/hpani.c:633: warning: ISO C90 forbids mixed declarations and code

Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Staging: otus: use USB API functions rather than constants

This set of patches introduces calls to the following set of functions:

usb_endpoint_dir_in(epd)
usb_endpoint_dir_out(epd)
usb_endpoint_is_bulk_in(epd)
usb_endpoint_is_bulk_out(epd)
usb_endpoint_is_int_in(epd)
usb_endpoint_is_int_out(epd)
usb_endpoint_num(epd)
usb_endpoint_type(epd)
usb_endpoint_xfer_bulk(epd)
usb_endpoint_xfer_control(epd)
usb_endpoint_xfer_int(epd)
usb_endpoint_xfer_isoc(epd)

In some cases, introducing one of these functions is not possible, and it
just replaces an explicit integer value by one of the following constants:

USB_ENDPOINT_XFER_BULK
USB_ENDPOINT_XFER_CONTROL
USB_ENDPOINT_XFER_INT
USB_ENDPOINT_XFER_ISOC

An extract of the semantic patch that makes these changes is as follows:
(http://www.emn.fr/x-info/coccinelle/)

// <smpl>
@r1@ struct usb_endpoint_descriptor *epd; @@

- ((epd->bmAttributes & \(USB_ENDPOINT_XFERTYPE_MASK\|3\)) ==
- \(USB_ENDPOINT_XFER_CONTROL\|0\))
+ usb_endpoint_xfer_control(epd)

@r5@ struct usb_endpoint_descriptor *epd; @@

- ((epd->bEndpointAddress & \(USB_ENDPOINT_DIR_MASK\|0x80\)) ==
-  \(USB_DIR_IN\|0x80\))
+ usb_endpoint_dir_in(epd)

@inc@
@@

#include <linux/usb.h>

@depends on !inc && (r1||r5)@
@@

+ #include <linux/usb.h>
  #include <linux/usb/...>
// </smpl>

Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Staging: otus: logical/bit and confusion

fix logical/bit and confusion

Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Cc: <lrodriguez@atheros.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Staging: mimio: depends on INPUT

mimio driver uses input_* functions so it needs to depend on INPUT.

mimio.c:(.text+0x2526c9): undefined reference to `input_unregister_device'
mimio.c:(.text+0x2526da): undefined reference to `input_close_device'
mimio.c:(.text+0x252725): undefined reference to `input_free_device'
mimio.c:(.text+0x2528f1): undefined reference to `input_event'
mimio.c:(.text+0x252904): undefined reference to `input_event'
mimio.c:(.text+0x252921): undefined reference to `input_event'
mimio.c:(.text+0x252b3e): undefined reference to `input_event'
mimio.c:(.text+0x252b51): undefined reference to `input_event'
drivers/built-in.o:mimio.c:(.text+0x252bbd): more undefined references to `input_event' follow
mimio.c:(.text+0x252e42): undefined reference to `input_allocate_device'
mimio.c:(.text+0x2530ef): undefined reference to `input_register_device'

Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Cc: mwilder@cs.nmsu.edu
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Staging: altera: fix printk format warnings

Fix printk format warnings in altera pcie chdma:

drivers/staging/altpciechdma/altpciechdma.c:429: warning: format '%08x' expects type 'unsigned int', but argument 3 has type 'dma_addr_t'
drivers/staging/altpciechdma/altpciechdma.c:433: warning: format '%08x' expects type 'unsigned int', but argument 3 has type 'dma_addr_t'
drivers/staging/altpciechdma/altpciechdma.c:449: warning: format '%08x' expects type 'unsigned int', but argument 3 has type 'dma_addr_t'
drivers/staging/altpciechdma/altpciechdma.c:450: warning: format '%08x' expects type 'unsigned int', but argument 3 has type 'dma_addr_t'

Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Staging: et131x: list usage cleanup

Trivial cleanup, list_del(); list_add_tail() is equivalent
to list_move_tail(). Semantic patch for coccinelle can be
found at www.cccmz.de/~snakebyte/list_move_tail.spatch

Signed-off-by: Eric Sesterhenn <snakebyte@gmx.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Staging: usbip: kmem_cache_alloc/memset -> kmem_cache_zalloc

Used kmem_cache_zalloc instead of kmem_cache_alloc/memset.

Signed-off-by: Wei Yongjun <yjwei@cn.fujitsu.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Staging: rspiusb: use USB API functions rather than constants

This set of patches introduces calls to the following set of functions:

usb_endpoint_dir_in(epd)
usb_endpoint_dir_out(epd)
usb_endpoint_is_bulk_in(epd)
usb_endpoint_is_bulk_out(epd)
usb_endpoint_is_int_in(epd)
usb_endpoint_is_int_out(epd)
usb_endpoint_num(epd)
usb_endpoint_type(epd)
usb_endpoint_xfer_bulk(epd)
usb_endpoint_xfer_control(epd)
usb_endpoint_xfer_int(epd)
usb_endpoint_xfer_isoc(epd)

In some cases, introducing one of these functions is not possible, and it
just replaces an explicit integer value by one of the following constants:

USB_ENDPOINT_XFER_BULK
USB_ENDPOINT_XFER_CONTROL
USB_ENDPOINT_XFER_INT
USB_ENDPOINT_XFER_ISOC

An extract of the semantic patch that makes these changes is as follows:
(http://www.emn.fr/x-info/coccinelle/)

// <smpl>
@r1@ struct usb_endpoint_descriptor *epd; @@

- ((epd->bmAttributes & \(USB_ENDPOINT_XFERTYPE_MASK\|3\)) ==
- \(USB_ENDPOINT_XFER_CONTROL\|0\))
+ usb_endpoint_xfer_control(epd)

@r5@ struct usb_endpoint_descriptor *epd; @@

- ((epd->bEndpointAddress & \(USB_ENDPOINT_DIR_MASK\|0x80\)) ==
-  \(USB_DIR_IN\|0x80\))
+ usb_endpoint_dir_in(epd)

@inc@
@@

#include <linux/usb.h>

@depends on !inc && (r1||r5)@
@@

+ #include <linux/usb.h>
  #include <linux/usb/...>
// </smpl>

Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Staging: at76_usb: convert to use linux/ieee80211.h

Jason Andryuk noticed that at76_usb won't compile with current
wireless-testing tree. This is because net/ieee80211.h was missing.

net/ieee80211.h will be removed soon and at76_usb won't compile then that
happens. Preprare for that by using instead linux/ieee80211.h and copying
some structures not available.

Signed-off-by: Kalle Valo <kalle.valo@iki.fi>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Staging: at76_usb: mention mac80211 port in TODO file

at76_usb has actually been already ported to use mac80211. Update the TODO
file to reflect this.

Signed-off-by: Kalle Valo <kalle.valo@iki.fi>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Staging: altpciechdma: checkpatch fixups

Signed-off-by: Erik Andrén <erik.andren@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Staging: altpciechdma: Null deref in altpciechdma.c remove()

If dev is NULL it prints an error message.  The error message dereferences
dev.

Compile tested only.

Signed-off-by: Dan Carpenter <error27@gmail.com>
Cc: Leon Woestenberg <leon.woestenberg@axon.tv>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Staging: meilhaus: some checkpatch.pl cleanup

Cc: David Kiliani <mail@davidkiliani.de>
Signed-off-by: Alexander Beregalov <a.beregalov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Staging: meilhaus: remove dependence on kernel version

Cc: David Kiliani <mail@davidkiliani.de>
Signed-off-by: Alexander Beregalov <a.beregalov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Staging: meilhaus: unsigned won't get negative after subtraction

Since unsigned, it won't get negative after subtraction.

Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Staging: meilhaus: Use DEFINE_SPINLOCK

SPIN_LOCK_UNLOCKED is deprecated.  The following makes the change suggested
in Documentation/spinlocks.txt

The semantic patch that makes this change is as follows:
(http://www.emn.fr/x-info/coccinelle/)

// <smpl>
@@
declarer name DEFINE_SPINLOCK;
identifier xxx_lock;
@@

- spinlock_t xxx_lock = SPIN_LOCK_UNLOCKED;
+ DEFINE_SPINLOCK(xxx_lock);
// </smpl>

Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Staging: meilhaus: Correct use of ! and &

ME_IO_SINGLE_TYPE_WRITE_NONBLOCKING and ME_IO_STREAM_CONFIG_WRAPAROUND both
hanve 0 as the rightmost bit, and thus eg
!flags & ME_IO_SINGLE_TYPE_WRITE_NONBLOCKING is always 0.
I assume that !(flags & ME_IO_SINGLE_TYPE_WRITE_NONBLOCKING) and
!(flags & ME_IO_STREAM_CONFIG_WRAPAROUND) were intended.

The semantic patch that makes this change is as follows:
(http://www.emn.fr/x-info/coccinelle/)

// <smpl>
@@ expression E; constant C; @@
(
  !E & !C
|
- !E & C
+ !(E & C)
)
// </smpl>

Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Staging: go7007: fix build error

VID_TYPE_CAPTURE is a v4l1 thing only.

Reported-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Staging: go7007: introduce missing kfree

Error handling code following a kmalloc should free the allocated data.

The semantic match that finds the problem is as follows:
(http://www.emn.fr/x-info/coccinelle/)

// <smpl>
@r exists@
local idexpression x;
statement S;
expression E;
identifier f,l;
position p1,p2;
expression *ptr != NULL;
@@

(
if ((x@p1 = \(kmalloc\|kzalloc\|kcalloc\)(...)) == NULL) S
|
x@p1 = \(kmalloc\|kzalloc\|kcalloc\)(...);
...
if (x == NULL) S
)
<... when != x
     when != if (...) { <+...x...+> }
x->f = E
...>
(
 return \(0\|<+...x...+>\|ptr\);
|
 return@p2 ...;
)

@script:python@
p1 << r.p1;
p2 << r.p2;
@@

print "* file: %s kmalloc %s return %s" % (p1[0].file,p1[0].line,p2[0].line)
// </smpl>

Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Staging: go7007: Move a dereference below a NULL test

In each case, if the NULL test is necessary, then the dereference should be
moved below the NULL test.

The semantic patch that makes this change is as follows:
(http://www.emn.fr/x-info/coccinelle/).  The result has been modified to
move the initialization of usb down closer to where it is used.

// <smpl>
@@
type T;
expression E;
identifier i,fld;
statement S;
@@

- T i = E->fld;
+ T i;
  ... when != E
      when != i
  if (E == NULL) S
+ i = E->fld;
// </smpl>

Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Staging: agnx: Fixup xmit.c checkpatch warnings

Signed-off-by: Erik Andrén <erik.andren@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Staging: agnx: Fixup table.c checkpatch warnings

Signed-off-by: Erik Andrén <erik.andren@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Staging: agnx: Fixup sta.h checkpatch warnings

Signed-off-by: Erik Andrén <erik.andren@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Staging: agnx: Fixup sta.c checkpatch warnings

Signed-off-by: Erik Andrén <erik.andren@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Staging: agnx: Fixup rf.c checkpatch warnings

Signed-off-by: Erik Andrén <erik.andren@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Staging: agnx: Fixup phy.c checkpatch warnings

Signed-off-by: Erik Andrén <erik.andren@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Staging: agnx: Fixup pci.c checkpatch warnings

Signed-off-by: Erik Andrén <erik.andren@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Staging: agnx: Fixup debug.h checkpatch warnings

Signed-off-by: Erik Andrén <erik.andren@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Staging: agnx: Fixup agnx.h checkpatch warnings

Signed-off-by: Erik Andrén <erik.andren@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Staging: agnx: mac80211 hw config change flags

Adapt agnx after commit "mac80211: introduce hw config change flags",
detected by following build warning:
drivers/staging/agnx/pci.c:426: warning: initialization from incompatible pointer type

Signed-off-by: Herton Ronaldo Krzesinski <herton@mandriva.com.br>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Staging: agnx: i reaches -1, tested 0

Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Staging: agnx: Move a dereference below a NULL test

If the NULL test is necessary, then the dereference should be moved below
the NULL test.

The semantic patch that makes this change is as follows:
(http://www.emn.fr/x-info/coccinelle/)

// <smpl>
@@
type T;
expression E;
identifier i,fld;
statement S;
@@

- T i = E->fld;
+ T i;
  ... when != E
      when != i
  if (E == NULL) S
+ i = E->fld;
// </smpl>

Signed-off-by: Julia Lawall <julia@diku.dk>
Cc: YanBo <dreamfly281@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Staging: remove duplicated #include's

Removed duplicated #include's in
  drivers/staging/altpciechdma/altpciechdma.c
  drivers/staging/comedi/comedidev.h
  drivers/staging/rt2860/rt_linux.h
  drivers/staging/rt2870/rt_linux.h

Signed-off-by: Huang Weiyi <weiyi.huang@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Staging: me4000: make file_operations const

This eliminates checkpatch.pl warnings, that struct file_operations is
usually const.  The structs me4000_ai_fops_array and
me4000_ao_fops_array are not modified and thus also made const.

Signed-off-by: Andre Haupt <andre@bitwigglers.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Staging: me4000: use tabs for code indentation

Signed-off-by: Andre Haupt <andre@bitwigglers.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Staging: me4000: do not use C99 style comments.

Signed-off-by: Andre Haupt <andre@bitwigglers.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Staging: me4000: fix various checkpatch.pl warnings about bracing

Signed-off-by: Andre Haupt <andre@bitwigglers.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Staging: me4000: kfree(NULL) is safe, so no extra checks needed.

Signed-off-by: Andre Haupt <andre@bitwigglers.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Staging: me4000: replace some C99 comments

checkpatch.pl triggered those as false positives for trailing
statements, but those lines also triggered some other warnings.

Signed-off-by: Andre Haupt <andre@bitwigglers.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Staging: me4000: inline keyword should sit between storage class and type

fixes some checkpatch.pl errors complaining about wrong position of the
inline keyword

Signed-off-by: Andre Haupt <andre@bitwigglers.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Staging: me4000: return is not a function, no parentheses required

fixes some checkpatch.pl errors about unneccessary parentheses.

Signed-off-by: Andre Haupt <andre@bitwigglers.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Staging: me4000: use linux/uaccess.h and linux/io.h

This fixes the following checkpatch.pl warnings:

WARNING: Use #include <linux/uaccess.h> instead of <asm/uaccess.h>
WARNING: Use #include <linux/io.h> instead of <asm/io.h>

Signed-off-by: Andre Haupt <andre@bitwigglers.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Staging: wlan-ng: block ioctls until card fully initialised

Add a mutex to block ioctls before the card is fully initialised and
only allow one ioctl at a time.
This stops udev trying to load the firmware before to card is fully up.

patch ported from wlan-ng-devel

Karl Relton <karllinuxtest.relton@ntlworld.com> spotted that this was
missing from the staging version,
http://lists.linux-wlan.com/pipermail/linux-wlan-devel/2009-February/003890.html

Signed-off-by: Richard Kennedy <richard@rsk.demon.co.uk>
Cc: Karl Relton <karllinuxtest.relton@ntlworld.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Staging: wlan-ng: Replace local byteorder macros

Replace hfa384x2host_16(), hfa384x2host_32(), host2hfa384x_16()
and host2hfa384x_32() with standard byteorder macros.

Signed-off-by: Moritz Muehlenhoff <jmm@debian.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Staging: wlan-ng: Remove the now empty wlan_compat.h

Signed-off-by: Moritz Muehlenhoff <jmm@debian.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Staging: wlan-ng: Remove dead code from p80211netdev.c

Signed-off-by: Moritz Muehlenhoff <jmm@debian.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Staging: wlan-ng: Remove unnecessary checks for NULL before calling kfree()

Signed-off-by: Moritz Muehlenhoff <jmm@debian.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Staging: wlan-ng: Remove more dead code from hfa384x_usb.c

Signed-off-by: Moritz Muehlenhoff <jmm@debian.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Staging: wlan-ng: Remove dead code from prism2mib.c

Signed-off-by: Moritz Muehlenhoff <jmm@debian.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Staging: wlan-ng: prism2mgmt.c: Coding style cleanups

Signed-off-by: Moritz Muehlenhoff <jmm@debian.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Staging: wlan-ng: hfa384x_usb.c: Coding style cleanups

Signed-off-by: Moritz Muehlenhoff <jmm@debian.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Staging: wlan-ng: p80211netdev.c: Coding style cleanups

Signed-off-by: Moritz Muehlenhoff <jmm@debian.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Staging: wlan-ng: prism2sta.c: Coding style cleanups

Signed-off-by: Moritz Muehlenhoff <jmm@debian.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Staging: wlan-ng: prism2usb.c: Coding style cleanups

Signed-off-by: Moritz Muehlenhoff <jmm@debian.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Staging: wlan-ng: prism2mib.c: Coding style cleanups

Signed-off-by: Moritz Muehlenhoff <jmm@debian.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Staging: wlan-ng: p80211mgmt.h: Coding style cleanups

Signed-off-by: Moritz Muehlenhoff <jmm@debian.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Staging: wlan-ng: p80211netdev.h: Coding style cleanups

Signed-off-by: Moritz Muehlenhoff <jmm@debian.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Staging: wlan-ng: p80211msg.h: Coding style cleanups

Signed-off-by: Moritz Muehlenhoff <jmm@debian.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Staging: wlan-ng: p80211types.h: Coding style cleanups

Signed-off-by: Moritz Muehlenhoff <jmm@debian.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Staging: wlan-ng: p80211conv.c: Coding style cleanups

Signed-off-by: Moritz Muehlenhoff <jmm@debian.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Staging: wlan-ng: p80211conv.h: Coding style cleanups

Signed-off-by: Moritz Muehlenhoff <jmm@debian.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Staging: wlan-ng: p80211hdr.h: Coding style cleanups

Signed-off-by: Moritz Muehlenhoff <jmm@debian.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Staging: wlan-ng: p80211metastruct.h: Coding style cleanups

Signed-off-by: Moritz Muehlenhoff <jmm@debian.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Staging: wlan-ng: p80211ioctl.h: Coding style cleanups

Signed-off-by: Moritz Muehlenhoff <jmm@debian.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Staging: wlan-ng: p80211meta.h: Coding style cleanups

Signed-off-by: Moritz Muehlenhoff <jmm@debian.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Staging: wlan-ng: p80211wext.c: Coding style cleanups

Signed-off-by: Moritz Muehlenhoff <jmm@debian.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>