Rusty Russell [Mon, 20 Apr 2009 05:14:02 +0000 (23:14 -0600)]
lguest: document 32-bit and PAE requirements
Robert noted that we don't actually document that lguest is 32-bit only,
nor that PAE must be off (CONFIG_PAE is now prompted for if HIGHMEM is
set to "off).
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Cc: lguest@ozlabs.org
Cc: "Robert P. J. Day" <rpjday@crashcourse.ca>
Matt Kraai [Fri, 17 Apr 2009 06:46:20 +0000 (23:46 -0700)]
lguest: tell git to ignore Documentation/lguest/lguest
This is the example lguest launcher binary.
Signed-off-by: Matt Kraai <kraai@ftbfs.org>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Marcelo Tosatti [Fri, 17 Apr 2009 00:14:04 +0000 (21:14 -0300)]
virtio: fix suspend when using virtio_balloon
Break out of wait_event_interruptible() if freezing has been requested,
in the vballoon thread. Without this change vballoon refuses to stop and
the system can't suspend.
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Cc: stable@kernel.org
Rusty Russell [Mon, 20 Apr 2009 05:14:00 +0000 (23:14 -0600)]
lguest: fix guest crash on non-linear addresses in gdt pvops
Fixes guest crash 'lguest: bad read address 0x4800000 len 256'
The new per-cpu allocator ends up handing a non-linear address to
write_gdt_entry. We do __pa() on it, and hand it to the host, which
kills us.
I've long wanted to make the hypercall "LOAD_GDT_ENTRY" to match the IDT
code, but had no pressing reason until now.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Cc: lguest@ozlabs.org
Matias Zabaljauregui [Wed, 8 Apr 2009 20:58:39 +0000 (17:58 -0300)]
lguest: fix crash on vmlinux images
Typical message: 'lguest: unhandled trap 6 at 0x418726 (0x0)'
vmlinux guests were broken by
4cd8b5e2a159f18a1507f1187b44a1acbfa6341b
'lguest: use KVM hypercalls', which rewrites guest text from kvm hypercalls
to trap 31.
The Launcher mmaps the kernel image. The Guest executes and
immediately faults in the first text page (read-only). Then it hits a
hypercall, and we rewrite that hypercall, causing a copy-on-write.
But the Guest pagetables still refer to the old page: we fault again,
but as Host we see the hypercall already rewritten, and pass the fault
back to the Guest. The Guest hasn't set up an IDT yet, so we kill it.
This doesn't happen with bzImages: they unpack themselves and so the
text pages are already read-write.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Tested-by: Patrick McHardy <kaber@trash.net>
Linus Torvalds [Sun, 19 Apr 2009 04:44:24 +0000 (21:44 -0700)]
Remove 'recurse into child resources' logic from 'reserve_region_with_split()'
This function is not actually used right now, since the original use
case for it was done with insert_resource_expand_to_fit() instead.
However, we now have another usage case that wants to basically do a
"reserve IO resource, splitting around existing resources", however that
one doesn't actually want the "recurse into the conflicting resource"
logic at all.
And since recursing into the conflicting resource was the most complex
part, and isn't wanted, just remove it. Maybe we'll some day want both
versions, but we can just resurrect the logic then.
Tested-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Sun, 19 Apr 2009 04:37:07 +0000 (21:37 -0700)]
Merge git://git./linux/kernel/git/sfrench/cifs-2.6
* git://git.kernel.org/pub/scm/linux/kernel/git/sfrench/cifs-2.6:
cifs: when renaming don't try to unlink negative dentry
cifs: remove unneeded bcc_ptr update in CIFSTCon
cifs: add cFYI messages with some of the saved strings from ssetup/tcon
cifs: fix buffer size for tcon->nativeFileSystem field
cifs: fix unicode string area word alignment in session setup
[CIFS] Fix build break caused by change to new current_umask helper function
[CIFS] Fix sparse warnings
[CIFS] Add support for posix open during lookup
cifs: no need to use rcu_assign_pointer on immutable keys
cifs: remove dnotify thread code
[CIFS] remove some build warnings
cifs: vary timeout on writes past EOF based on offset (try #5)
[CIFS] Fix build break from recent DFS patch when DFS support not enabled
Remote DFS root support.
[CIFS] Endian convert UniqueId when reporting inode numbers from server files
cifs: remove some pointless conditionals before kfree()
cifs: flush data on any setattr
Linus Torvalds [Sat, 18 Apr 2009 19:07:25 +0000 (12:07 -0700)]
Merge branch 'for-linus' of git://git./linux/kernel/git/bart/ide-2.6
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/bart/ide-2.6:
cs5536: define dma_sff_read_status() method
ide: fix barriers support
ide: Remove void casts
hpt366: use ATA_DMA_* constants
hpt366: fix HPT370 DMA timeouts
Linus Torvalds [Sat, 18 Apr 2009 18:37:50 +0000 (11:37 -0700)]
Merge branch 'for-linus' of git://git./linux/kernel/git/jmorris/security-testing-2.6
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/security-testing-2.6:
Smack: check for SMACK xattr validity in smack_inode_setxattr
Randy Dunlap [Sat, 18 Apr 2009 01:30:28 +0000 (18:30 -0700)]
doc: fix kernel-parameters.txt mistaken deletions
Re-add missing kernel-parameters documentation that was accidentally
deleted in commit
0cb55ad2.
Thanks to Ingo and Weidong Han for the heads-up on this.
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
cc: Ingo Molnar <mingo@elte.hu>
cc: Len Brown <lenb@kernel.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Rafael J. Wysocki [Sat, 18 Apr 2009 15:23:41 +0000 (17:23 +0200)]
PM/Hibernate: Fix memory shrinking
Commit
d979677c4c0 ("mm: shrink_all_memory(): use sc.nr_reclaimed")
broke the memory shrinking used by hibernation, becuse it did not update
shrink_all_zones() in accordance with the other changes it made.
Fix this by making shrink_all_zones() update sc->nr_reclaimed instead of
overwriting its value.
This fixes http://bugzilla.kernel.org/show_bug.cgi?id=13058
Reported-and-tested-by: Alan Jenkins <alan-jenkins@tuffmail.co.uk>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Sergei Shtylyov [Sat, 18 Apr 2009 15:42:20 +0000 (17:42 +0200)]
cs5536: define dma_sff_read_status() method
The driver somehow got merged with the initializer for the dma_sff_read_status()
method missing which caused kernel panic on bootup.
This should fix the kernel.org bug #13026...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Reported-by: Arnd Hannemann <hannemann@nets.rwth-aachen.de>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Bartlomiej Zolnierkiewicz [Sat, 18 Apr 2009 15:42:20 +0000 (17:42 +0200)]
ide: fix barriers support
Freeing non-slab objects is bad and results in an oops. Fix it.
Reported-and-tested-by: Andrew Price <andy@andrewprice.me.uk>
Cc: Theodore Tso <tytso@mit.edu>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Jack Stone [Sat, 18 Apr 2009 15:42:19 +0000 (17:42 +0200)]
ide: Remove void casts
Remove uneeded void casts
Signed-off-by: Jack Stone <jwjstone@fastmail.fm>
Cc: jeff@garzik.org
Cc: kernel-janitors@vger.kernel.org
Cc: Jack Stone <jwjstone@fastmail.fm>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Sergei Shtylyov [Sat, 18 Apr 2009 15:42:19 +0000 (17:42 +0200)]
hpt366: use ATA_DMA_* constants
Use ATA_DMA_* constants instead of the bare numbers for the BMIDE register bits.
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Sergei Shtylyov [Sat, 18 Apr 2009 15:42:19 +0000 (17:42 +0200)]
hpt366: fix HPT370 DMA timeouts
The big driver change in 2.4.19-rc1 introduced a regression for many HPT370[A]
chips -- DMA stopped to work completely, only causing endless timeouts...
The culprit has been identified (at last!): it turned to be the code resetting
the DMA state machine before each transfer. Stop doing it now as this counter-
measure has clearly caused more harm than good.
This should fix the kernel.org bug #7703.
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Etienne Basset [Thu, 16 Apr 2009 21:58:42 +0000 (23:58 +0200)]
Smack: check for SMACK xattr validity in smack_inode_setxattr
the following patch moves checks for SMACK xattr validity
from smack_inode_post_setxattr (which cannot return an error to the user)
to smack_inode_setxattr (which can return an error).
Signed-off-by: Etienne Basset <etienne.basset@numericable.fr>
Acked-by: Casey Schaufler <casey@schaufler-ca.com>
Signed-off-by: James Morris <jmorris@namei.org>
Linus Torvalds [Fri, 17 Apr 2009 23:20:29 +0000 (16:20 -0700)]
Merge branch 'upstream-linus' of git://git./linux/kernel/git/jgarzik/libata-dev
* 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev:
[libata] fix build error on drivers/ata/pata_legacy.c
pata_via: Cache and rewrite the device bit
sata_mv: workaround for multi_count errata sata24
sata_mv: tidy up qc->tf usage in qc_prep() functions
Zhenwen Xu [Fri, 17 Apr 2009 07:32:59 +0000 (15:32 +0800)]
[libata] fix build error on drivers/ata/pata_legacy.c
fix those errors:
drivers/ata/pata_legacy.c: In function ‘pdc_data_xfer_vlb’:
drivers/ata/pata_legacy.c:289: error: ‘ap’ undeclared (first use in this function)
drivers/ata/pata_legacy.c:289: error: (Each undeclared identifier is reported only once
drivers/ata/pata_legacy.c:289: error: for each function it appears in.)
drivers/ata/pata_legacy.c: At top level:
drivers/ata/pata_legacy.c:869: error: ‘ATA_PFLAG_PIO32_CHANGE’ undeclared here (not in a
+function)
make[2]: *** [drivers/ata/pata_legacy.o] Error 1
make[1]: *** [drivers/ata] Error 2
Signed-off-by: Zhenwen Xu <helight.xu@gmail.com>
Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Alan Cox [Fri, 17 Apr 2009 11:21:21 +0000 (12:21 +0100)]
pata_via: Cache and rewrite the device bit
Some VIA chipsets will reset the DEV bit after IEN changes on ctl. Our
optimised write path avoids doing this but we need to remove the
optimisation on these devices.
[Identified and some original patches proposed by Josehn Chan @ VIA but
discussion then all ground to a halt so given a test case I dug it back out]
Signed-off-by: Alan Cox <alan@lxorguk.ukuu.org.uk
Tested-by: Christoph Bisping (bug #13086)
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Mark Lord [Mon, 13 Apr 2009 15:29:34 +0000 (11:29 -0400)]
sata_mv: workaround for multi_count errata sata24
Workaround for errata SATA#24 in sata_mv.
This errata affects WRITE_MULTI* commands when
the device multi_count produces a DRQ block size >= 4Kbytes.
We work around it here by converting such operations
into ordinary PIO_WRITEs instead.
Note that this might result in a PIO FUA write unavoidably being converted
into a non-FUA write. In practice, any system using FUA is also going to be
using DMA rather than PIO, so this shouldn't affect anyone in the real world.
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Mark Lord [Mon, 13 Apr 2009 15:27:18 +0000 (11:27 -0400)]
sata_mv: tidy up qc->tf usage in qc_prep() functions
Tidy up qc->tf accesses in the mv_qc_prep() functions.
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Jeff Layton [Fri, 17 Apr 2009 15:45:30 +0000 (11:45 -0400)]
cifs: when renaming don't try to unlink negative dentry
When attempting to rename a file on a read-only share, the kernel can
call cifs_unlink on a negative dentry, which causes an oops. Only try
to unlink the file if it's a positive dentry.
Signed-off-by: Jeff Layton <jlayton@redhat.com>
Tested-by: Shirish Pargaonkar <shirishp@us.ibm.com>
CC: Stable <stable@vger.kernel.org>
Signed-off-by: Steve French <sfrench@us.ibm.com>
Linus Torvalds [Fri, 17 Apr 2009 20:53:34 +0000 (13:53 -0700)]
Merge git://git./linux/kernel/git/gregkh/staging-2.6
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging-2.6: (43 commits)
staging: slicoss: update README
otus/zdusb.c: additional USB idnetifier
Staging: go7007: fix build issues
Staging: sxg: Fix leaks and checksum errors in transmit code path
Staging: sxg: Fix sleep in atomic context warning while loading driver
Staging: sxg: Use correct queue_id for transmitting non-TCP packets
Staging: sxg: Fire watchdog timer at end of open routine to change the link
Staging: Pohmelfs: Add load balancing between network states with the same priority.
Staging: Pohmelfs: Added IO permissions and priorities.
Staging: Pohmelfs: Added ->show_stats() callback.
Staging: Pohmelfs: Drop ftrans debugging code.
Staging: Pohmelfs: Use wait_on_page_timeout when waiting for remote directory sync instead of hardcoded 25 seconds.
Staging: Pohmelfs: Reduce debugging noise about non-existing objects.
Staging: Pohmelfs: Sync fs before killing it, since dentry cache is shrunk before writeback is invoked via generic_shutdown_super()
Staging: Pohmelfs: Extend remount option.
Staging: Pohmelfs: Set NETFS_INODE_REMOTE_SYNCED and clear NETFS_INODE_OWNED bits in the root inode.
Staging: Pohmelfs: Added 'need_lock' variable into debug print.
Staging: Pohmelfs: Disable read lock in pohmelfs_getattr().
Staging: Pohmelfs: Move parent lock to the place where we really have to send a lookup request to the server.
Staging: pohmelfs: Populate dentry cache when receiving the new readdir entry.
...
Linus Torvalds [Fri, 17 Apr 2009 20:53:16 +0000 (13:53 -0700)]
Merge git://git./linux/kernel/git/gregkh/driver-core-2.6
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core-2.6:
UIO: fix specific device driver missing statement for depmod
Driver core: remove pr_fmt() from dynamic_dev_dbg() printk
driver core: prevent device_for_each_child from oopsing
dynamic debug: resurrect old pr_debug() semantics as pr_devel()
Driver Core: early platform driver
proc: mounts_poll() make consistent to mdstat_poll
sysfs: sysfs poll keep the poll rule of regular file.
driver core: allow non-root users to listen to uevents
driver core: fix driver_match_device
sysfs: don't use global workqueue in sysfs_schedule_callback()
Linus Torvalds [Fri, 17 Apr 2009 20:53:00 +0000 (13:53 -0700)]
Merge git://git./linux/kernel/git/gregkh/usb-2.6
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb-2.6: (22 commits)
WUSB: correct format of wusb_chid sysfs file
WUSB: fix oops when completing URBs for disconnected devices
WUSB: disconnect all devices when stopping a WUSB HCD
USB: whci-hcd: check return value of usb_hcd_link_urb_to_ep()
USB: whci-hcd: provide a endpoint_reset method
USB: add reset endpoint operations
USB device codes for Motorola phone.
usb-storage: fix mistake in Makefile
USB: usb-serial ch341: support for DTR/RTS/CTS
Revert USB: usb-serial ch341: support for DTR/RTS/CTS
USB: musb: fix possible panic while resuming
USB: musb: fix isochronous TXDMA (take 2)
USB: musb: sanitize clearing TXCSR DMA bits (take 2)
USB: musb: bugfixes for multi-packet TXDMA support
USB: musb_host, fix ep0 fifo flushing
USB: usb-storage: augment unusual_devs entry for Simple Tech/Datafab
USB: musb_host, minor enqueue locking fix (v2)
USB: fix oops in cdc-wdm in case of malformed descriptors
USB: qcserial: Add extra device IDs
USB: option: Add ids for D-Link DWM-652 3.5G modem
...
Linus Torvalds [Fri, 17 Apr 2009 20:51:14 +0000 (13:51 -0700)]
Merge master.kernel.org:/home/rmk/linux-2.6-arm
* master.kernel.org:/home/rmk/linux-2.6-arm: (48 commits)
[ARM] S3C24XX: ADC: Check pending queue before freeing adc client
[ARM] S3C: Fix ADC driver sparse warning
[ARM] Osiris: Fix double initialisation in machine block
[ARM] Anubis: Fix sparse warnings for items that should be static
[ARM] JIVE: Fix sparse warnings about items which should be static
[ARM] S3C: Fix sparse warning from missing 's3c_device_hwmon'
[ARM] S3C24XX: Fix sparse error in gpiolib.c
[ARM] 5455/1: Fix IRQ noise from VIC code
[ARM] 5454/1: ep93xx_eth: fix sparse warnings
[ARM] remove .gitignore from include/asm-arm
Update MAINTAINERS
mxc defconfig updates
mx31ads: Mark as having full regulatoion constraints with 1133-EV1 board
mx31ads: Depend on all the WM8350 core dependencies for WM1133-EV1 board
Fix ifdef in plat-mxc/irc.c
MX1ADS: remove I2C ifdefs
qong: remove AIPS[12] mappings from machine-specific iotable
mx31ads: imoux pins should be passed in as unsigned int
MXC: remove orphan imx_init_uart() definition
mx31: pin definition for csi
...
Russell King [Fri, 17 Apr 2009 20:35:56 +0000 (21:35 +0100)]
Merge branch 'defconfig-s3c2410' of git://aeryn.fluff.org.uk/bjdooks/linux
Russell King [Fri, 17 Apr 2009 20:35:44 +0000 (21:35 +0100)]
Merge branch 'v2630-rc2-fixes' of git://aeryn.fluff.org.uk/bjdooks/linux
Stephen Hemminger [Wed, 15 Apr 2009 23:52:16 +0000 (16:52 -0700)]
staging: slicoss: update README
I looked, I gagged, I left
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Daniele Napolitano [Tue, 14 Apr 2009 23:58:33 +0000 (16:58 -0700)]
otus/zdusb.c: additional USB idnetifier
Provide support for WN111v2 USB 802.11n adapter.
Signed-off-by: Daniele Napolitano <dnax88@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Greg Kroah-Hartman [Mon, 13 Apr 2009 20:16:54 +0000 (13:16 -0700)]
Staging: go7007: fix build issues
Now that TUNER_SET_TYPE_ADDR is gone from the tree, the older code kicks
in and tries to use TUNER_SET_TYPE, which went away a long time ago.
This patch removes all of this logic, as it should not be needed anymore
now, and by doing so, fixes the build.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Mithlesh Thukral [Wed, 25 Mar 2009 10:21:49 +0000 (15:51 +0530)]
Staging: sxg: Fix leaks and checksum errors in transmit code path
Fix the transmit function for the following:
* Free XmtCmd in the error code path. This use to leak memory in
error conditions.
* Do pci mapping after the checksum operations are over. They can
reallocate the skb at a different location.
* Fix UDP checksum errors which were seen in wireshark
Signed-off-by: LinSysSoft Sahara Team <saharaproj@linsyssoft.com>
Signed-off-by: Mithlesh Thukral <mithlesh@linsyssoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Mithlesh Thukral [Wed, 25 Mar 2009 10:21:14 +0000 (15:51 +0530)]
Staging: sxg: Fix sleep in atomic context warning while loading driver
Leave a spinlock before calling request_irq(). request_irq() calls kmalloc
which can sleep. This was generating a warning dump while driver is loaded.
Signed-off-by: LinSysSoft Sahara Team <saharaproj@linsyssoft.com>
Signed-off-by: Mithlesh Thukral <mithlesh@linsyssoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Mithlesh Thukral [Wed, 25 Mar 2009 10:20:34 +0000 (15:50 +0530)]
Staging: sxg: Use correct queue_id for transmitting non-TCP packets
Use correct queue_id while transmitting non-TCP packets.
They should always use queue 0.
Signed-off-by: LinSysSoft Sahara Team <saharaproj@linsyssoft.com>
Signed-off-by: Mithlesh Thukral <mithlesh@linsyssoft.com>
Mithlesh Thukral [Wed, 25 Mar 2009 10:19:58 +0000 (15:49 +0530)]
Staging: sxg: Fire watchdog timer at end of open routine to change the link
The watchdog timer which updates the link status was not fired at the
end of sxg_entry_open(). Add that.
Signed-off-by: LinSysSoft Sahara Team <saharaproj@linsyssoft.com>
Signed-off-by: Mithlesh Thukral <mithlesh@linsyssoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Evgeniy Polyakov [Fri, 27 Mar 2009 12:04:30 +0000 (15:04 +0300)]
Staging: Pohmelfs: Add load balancing between network states with the same priority.
Signed-off-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Evgeniy Polyakov [Fri, 27 Mar 2009 12:04:29 +0000 (15:04 +0300)]
Staging: Pohmelfs: Added IO permissions and priorities.
Signed-off-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Evgeniy Polyakov [Fri, 27 Mar 2009 12:04:28 +0000 (15:04 +0300)]
Staging: Pohmelfs: Added ->show_stats() callback.
Signed-off-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Evgeniy Polyakov [Fri, 27 Mar 2009 12:04:27 +0000 (15:04 +0300)]
Staging: Pohmelfs: Drop ftrans debugging code.
Signed-off-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Evgeniy Polyakov [Fri, 27 Mar 2009 12:04:26 +0000 (15:04 +0300)]
Staging: Pohmelfs: Use wait_on_page_timeout when waiting for remote directory sync instead of hardcoded 25 seconds.
Signed-off-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Evgeniy Polyakov [Fri, 27 Mar 2009 12:04:25 +0000 (15:04 +0300)]
Staging: Pohmelfs: Reduce debugging noise about non-existing objects.
Signed-off-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Evgeniy Polyakov [Fri, 27 Mar 2009 12:04:24 +0000 (15:04 +0300)]
Staging: Pohmelfs: Sync fs before killing it, since dentry cache is shrunk before writeback is invoked via generic_shutdown_super()
Signed-off-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Evgeniy Polyakov [Fri, 27 Mar 2009 12:04:23 +0000 (15:04 +0300)]
Staging: Pohmelfs: Extend remount option.
Signed-off-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Evgeniy Polyakov [Fri, 27 Mar 2009 12:04:22 +0000 (15:04 +0300)]
Staging: Pohmelfs: Set NETFS_INODE_REMOTE_SYNCED and clear NETFS_INODE_OWNED bits in the root inode.
Signed-off-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Evgeniy Polyakov [Fri, 27 Mar 2009 12:04:21 +0000 (15:04 +0300)]
Staging: Pohmelfs: Added 'need_lock' variable into debug print.
Signed-off-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Evgeniy Polyakov [Fri, 27 Mar 2009 12:04:20 +0000 (15:04 +0300)]
Staging: Pohmelfs: Disable read lock in pohmelfs_getattr().
Signed-off-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Evgeniy Polyakov [Fri, 27 Mar 2009 12:04:19 +0000 (15:04 +0300)]
Staging: Pohmelfs: Move parent lock to the place where we really have to send a lookup request to the server.
Signed-off-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Evgeniy Polyakov [Fri, 27 Mar 2009 12:04:18 +0000 (15:04 +0300)]
Staging: pohmelfs: Populate dentry cache when receiving the new readdir entry.
Signed-off-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Lior Dotan [Wed, 11 Feb 2009 11:35:10 +0000 (13:35 +0200)]
Revert Staging: SLICOSS: use gfp_kernel where possible
Revert commit
2bb347361e2c19799431f56488a3f64de40a3aa6
This commit has been reported to cause problems:
Mar 24 11:50:31 linuxdev kernel: BUG: sleeping function called from invalid context at mm/slub.c:1599 Mar 24 11:50:31 linuxdev kernel: in_atomic(): 1, irqs_disabled(): 0, pid: 3251, name: avahi-daemon
Cc: Lior Dotan <liodot@gmail.com>
Cc: Christopher Harrer <charrer@alacritech.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Geert Uytterhoeven [Mon, 6 Apr 2009 13:15:55 +0000 (15:15 +0200)]
Staging: STLC45XX should depend on GENERIC_HARDIRQS
m68k allmodconfig:
| drivers/staging/stlc45xx/stlc45xx.c: In function 'stlc45xx_probe':
| drivers/staging/stlc45xx/stlc45xx.c:2456: error: implicit declaration of function 'set_irq_type'
| make[6]: *** [drivers/staging/stlc45xx/stlc45xx.o] Error 1
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Arve Hjønnevåg [Mon, 6 Apr 2009 22:13:00 +0000 (15:13 -0700)]
Staging: binder: Defer flush and release operations to avoid deadlocks.
If a transaction that contains a file descriptor fails on a later object,
the new file descriptor needs to be closed. If this is a binder file
descriptor we would deadlock in flush. If there were no other references to
the file at this point release would also be called.
Signed-off-by: Arve Hjønnevåg <arve@android.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Arve Hjønnevåg [Mon, 6 Apr 2009 22:12:59 +0000 (15:12 -0700)]
Staging: binder: Prevent the wrong thread from adding a transaction to the stack.
If a thread is part of a transaction stack, it is only allowed to make
another call if it was the target of the top transaction on the stack.
Signed-off-by: Arve Hjønnevåg <arve@android.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Arve Hjønnevåg [Mon, 6 Apr 2009 22:12:58 +0000 (15:12 -0700)]
Staging: binder: Cast to uintptr_t instead of size_t when aligning pointers
Signed-off-by: Arve Hjønnevåg <arve@android.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Arve Hjønnevåg [Mon, 6 Apr 2009 22:12:57 +0000 (15:12 -0700)]
Staging: binder: Keep a reference to the files_struct while the driver is mmapped
This prevents breaking fget_light if a single threaded application
allows incoming file descriptors (in replies or on nodes).
Should also prevent inserting a file in the wrong files_struct if the
receving process execs in the middle of a transaction (between
task_get_unused_fd_flags and task_fd_install).
Signed-off-by: Arve Hjønnevåg <arve@android.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Arve Hjønnevåg [Mon, 6 Apr 2009 22:12:56 +0000 (15:12 -0700)]
Staging: binder: Add more offset validation.
Check that datasize is not smaller than one flat_binder_object.
Check that offsets are aligned.
Check that offsets_size is aligned.
Signed-off-by: Arve Hjønnevåg <arve@android.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Arve Hjønnevåg [Mon, 6 Apr 2009 22:12:55 +0000 (15:12 -0700)]
Staging: binder: mmap fixes.
Only allow a binder file pointer to be mmapped once. The buffer management
code cannot deal with more then one area.
Also remove leftover mutex_unlock if mmap fails.
Signed-off-by: Arve Hjønnevåg <arve@android.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Arve Hjønnevåg [Mon, 6 Apr 2009 22:12:54 +0000 (15:12 -0700)]
Staging: binder: Don't create two proc entries with the same name if the driver is opened twice in one process.
Signed-off-by: Arve Hjønnevåg <arve@android.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Arve Hjønnevåg [Mon, 6 Apr 2009 22:12:53 +0000 (15:12 -0700)]
Staging: binder: Remove VM_EXEC check.
Many platforms do not support mappings without VM_EXEC.
Signed-off-by: Arve Hjønnevåg <arve@android.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Alan Cox [Tue, 7 Apr 2009 17:43:43 +0000 (18:43 +0100)]
Staging: aten2011: Clean up some tty bits
Minor fixes for tty layer stuff in this driver
Signed-off-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Daniele Napolitano [Wed, 1 Apr 2009 21:53:39 +0000 (14:53 -0700)]
Staging: rt2870: add ID for Sitecom WL-315
Signed-off-by: Daniele Napolitano <dnax88@gmail.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Alexander Beregalov [Sun, 29 Mar 2009 15:59:13 +0000 (19:59 +0400)]
Staging: line6: convert to snd_card_create()
Signed-off-by: Alexander Beregalov <a.beregalov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Alexander Beregalov [Sun, 29 Mar 2009 15:31:28 +0000 (19:31 +0400)]
Staging: wlan-ng: convert to netdev_ops
Signed-off-by: Alexander Beregalov <a.beregalov@gmail.com>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Alexander Beregalov [Sun, 29 Mar 2009 15:30:46 +0000 (19:30 +0400)]
Staging: sxg: convert to netdev_ops
Signed-off-by: Alexander Beregalov <a.beregalov@gmail.com>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Alexander Beregalov [Sun, 29 Mar 2009 15:30:08 +0000 (19:30 +0400)]
Staging: slicoss: convert to netdev_ops
Signed-off-by: Alexander Beregalov <a.beregalov@gmail.com>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Alexander Beregalov [Sun, 29 Mar 2009 15:29:18 +0000 (19:29 +0400)]
Staging: rt3070: convert to netdev_ops
Also remove unused variable.
Signed-off-by: Alexander Beregalov <a.beregalov@gmail.com>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Alexander Beregalov [Sun, 29 Mar 2009 15:28:11 +0000 (19:28 +0400)]
Staging: rt2870: convert to netdev_ops
Signed-off-by: Alexander Beregalov <a.beregalov@gmail.com>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Alexander Beregalov [Sun, 29 Mar 2009 15:27:21 +0000 (19:27 +0400)]
Staging: rt2860: convert to netdev_ops
Signed-off-by: Alexander Beregalov <a.beregalov@gmail.com>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Alexander Beregalov [Sun, 29 Mar 2009 15:26:25 +0000 (19:26 +0400)]
Staging: otus: convert to netdev_ops
Signed-off-by: Alexander Beregalov <a.beregalov@gmail.com>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Alexander Beregalov [Sun, 29 Mar 2009 15:25:33 +0000 (19:25 +0400)]
Staging: et131x: convert to netdev_ops
Signed-off-by: Alexander Beregalov <a.beregalov@gmail.com>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Alexander Beregalov [Sun, 29 Mar 2009 15:24:32 +0000 (19:24 +0400)]
Staging: epl: convert to netdev_ops
Signed-off-by: Alexander Beregalov <a.beregalov@gmail.com>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Alexander Beregalov [Sun, 29 Mar 2009 15:23:34 +0000 (19:23 +0400)]
Staging: at76: convert to netdev_ops
Signed-off-by: Alexander Beregalov <a.beregalov@gmail.com>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
David Vrabel [Wed, 8 Apr 2009 17:36:30 +0000 (17:36 +0000)]
WUSB: correct format of wusb_chid sysfs file
Make the wusb_chid sysfs file match the ABI documentation.
Print all zeros if the WUSB host is stopped (instead of an empty file)
and end the file with a newline.
Signed-off-by: David Vrabel <david.vrabel@csr.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
David Vrabel [Wed, 8 Apr 2009 17:36:32 +0000 (17:36 +0000)]
WUSB: fix oops when completing URBs for disconnected devices
Fix an oops in wusbhc_giveback_urb() if the wusb device had disconnected
while an urb was in progress. Also release the ref count obtained here.
Signed-off-by: David Vrabel <david.vrabel@csr.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
David Vrabel [Wed, 8 Apr 2009 17:36:33 +0000 (17:36 +0000)]
WUSB: disconnect all devices when stopping a WUSB HCD
Make sure all WUSB devices are disconnected when stopping a WUSB HCD so
that we don't leak the devices' wusb_dev structures.
Signed-off-by: David Vrabel <david.vrabel@csr.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
David Vrabel [Wed, 8 Apr 2009 17:36:31 +0000 (17:36 +0000)]
USB: whci-hcd: check return value of usb_hcd_link_urb_to_ep()
Check the return value of usb_hcd_link_urb_to_ep() and do not add the
urb to the ASL/PZL if it returns an error.
Omitting the check results in urbs that appear to be submitted
successfully but then cannot be unliked (because
usb_hcd_check_unlink_urb() returns an error). This can cause khubd (for
example) to block forever in usb_kill_urb().
Signed-off-by: David Vrabel <david.vrabel@csr.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
David Vrabel [Wed, 8 Apr 2009 17:36:29 +0000 (17:36 +0000)]
USB: whci-hcd: provide a endpoint_reset method
Provide a endpoint_reset method to reset sequence number and current
window. This QHead information can only be changed while the qset is
not in a schedule.
Signed-off-by: David Vrabel <david.vrabel@csr.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
David Vrabel [Wed, 8 Apr 2009 17:36:28 +0000 (17:36 +0000)]
USB: add reset endpoint operations
Wireless USB endpoint state has a sequence number and a current
window and not just a single toggle bit. So allow HCDs to provide a
endpoint_reset method and call this or clear the software toggles as
required (after a clear halt, set configuration etc.).
usb_settoggle() and friends are then HCD internal and are moved into
core/hcd.h and all device drivers call usb_reset_endpoint() instead.
If the device endpoint state has been reset (with a clear halt) but
the host endpoint state has not then subsequent data transfers will
not complete. The device will only work again after it is reset or
disconnected.
Signed-off-by: David Vrabel <david.vrabel@csr.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Dr. Greg Wettstein [Sat, 11 Apr 2009 14:12:08 +0000 (09:12 -0500)]
USB device codes for Motorola phone.
The v950 appears to be a ruggedized version of the Motorola Razor
phone. Tethering to the phone to use it in 'phone as modem' mode
requires the use of the specialized moto-modem driver which layers
over the usb-serial driver. Support for the v950 was added simply
adding the device ID's for the phone.
Signed-off-by: Dr. Greg Wettstein <greg@enjellic.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Alan Stern [Thu, 9 Apr 2009 18:59:44 +0000 (14:59 -0400)]
usb-storage: fix mistake in Makefile
This patch (as1228) fixes a Makefile error introduced when the
subdrivers in usb-storage were split out into separate modules. The
intention is that when CONFIG_USB_LIBUSUAL is set, libusual.o and
usual-tables.o should be combined into a single object file (called
usb-libusual). The current Makefile will instead create two separate
objects, and the result won't load properly.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-and-tested-by: Alan Jenkins <sourcejedi.lkml@googlemail.com>
Reported-and-tested-by: Mike Galbraith <efault@gmx.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Werner Cornelius [Fri, 16 Jan 2009 20:02:41 +0000 (21:02 +0100)]
USB: usb-serial ch341: support for DTR/RTS/CTS
commit
664d5df92e88b6ef091048a802b3750f4e989180 upstream.
Fixup of Werner Cornelius patch to the ch341 USB-serial driver, which adds:
- support all baudrates, not just a hard-coded set
- support for controlling DTR, RTS and CTS
Features still missing:
- character length other than 8 bits
- parity settings
- break control
I adapted his patch for the new usb_serial API introduced in 2.6.25-git8 by
Alan Cox on 22 July 2008. Non-compliance to the new API was a reason for
refusing a similar patch from Tollef Fog Heen.
Usage example by Tollef Fog Heen :
TEMPer USB thermometer <http://err.no/src/TEMPer.c>
based on a patch by:
From: Tollef Fog Heen <tfheen@err.no>
* Implement support for all baud rates rather than just a hard
coded set.
* Make it possible to control status and control lines
* Grab a bunch of #defines from FreeBSD to reduce the number of
magic numbers in the file
Signed-off-by: Werner Cornelius <Werner.Cornelius@cornelius-consult.de>
Signed-off-by: Boris Hajduk <boris@hajduk.org>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Tollef Fog Heen <tfheen@err.no>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Greg Kroah-Hartman [Tue, 7 Apr 2009 18:56:32 +0000 (11:56 -0700)]
Revert USB: usb-serial ch341: support for DTR/RTS/CTS
Reverts commit
664d5df92e88b6ef091048a802b3750f4e989180 as the commit
log information was not complete, and we didn't have a proper
signed-off-by by the author of the original BSD code.
Cc: Werner Cornelius <Werner.Cornelius@cornelius-consult.de>
Cc: Boris Hajduk <boris@hajduk.org>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Kim Kyuwon [Fri, 27 Mar 2009 01:56:51 +0000 (18:56 -0700)]
USB: musb: fix possible panic while resuming
During driver resume processing, musb could cause a kernel panic.
Fix by enabling the clock earlier, with the resume_early method.
Signed-off-by: Kim Kyuwon <q1.kim@samsung.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Sergei Shtylyov [Fri, 27 Mar 2009 01:29:19 +0000 (18:29 -0700)]
USB: musb: fix isochronous TXDMA (take 2)
Multi-frame isochronous TX URBs transfers in DMA mode never
complete with CPPI DMA because musb_host_tx() doesn't restart
DMA on the second frame, only emitting a debug message.
With Inventra DMA they complete, but in PIO mode. To fix:
- Factor out programming of the DMA transfer from
musb_ep_program() into musb_tx_dma_program();
- Reorder the code at the end of musb_host_tx() to
facilitate the fallback to PIO iff DMA fails;
- Handle the buffer offset consistently for both
PIO and DMA modes;
- Add an argument to musb_ep_program() for the same
reason (it only worked correctly with non-zero
offset of the first frame in PIO mode);
- Set the completed isochronous frame descriptor's
'actual_length' and 'status' fields correctly in
DMA mode.
Also, since CPPI reportedly doesn't like sending isochronous
packets in the RNDIS mode, change the criterion for this
mode to be used only for multi-packet transfers. (There's
no need for that mode in the single-packet case anyway.)
[ dbrownell@users.sourceforge.net: split comment paragraph
into bullet list, shrink patch delta, style tweaks ]
Signed-off-by: Pavel Kiryukhin <pkiryukhin@ru.mvista.com>
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Sergei Shtylyov [Fri, 27 Mar 2009 01:27:47 +0000 (18:27 -0700)]
USB: musb: sanitize clearing TXCSR DMA bits (take 2)
The MUSB code clears TXCSR_DMAMODE incorrectly in several
places, either asserting that TXCSR_DMAENAB is clear (when
sometimes it isn't) or clearing both bits together. Recent
versions of the programmer's guide require DMAENAB to be
cleared first, although some older ones didn't.
Fix this and while at it:
- In musb_gadget::txstate(), stop clearing the AUTOSET
and DMAMODE bits for the CPPI case since they never
get set anyway (the former bit is reserved on DaVinci);
but do clear the DMAENAB bit on the DMA error path.
- In musb_host::musb_ep_program(), remove the duplicate
DMA controller specific code code clearing the TXCSR
previous state, add the code to clear TXCSR DMA bits
on the Inventra DMA error path, to replace such code
(executed late) on the PIO path.
- In musbhsdma::dma_channel_abort()/dma_controller_irq(),
add/use the 'offset' variable to avoid MUSB_EP_OFFSET()
invocations on every RXCSR/TXCSR access.
[dbrownell@users.sourceforge.net: don't introduce CamelCase,
shrink diff]
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Sergei Shtylyov [Fri, 27 Mar 2009 01:26:40 +0000 (18:26 -0700)]
USB: musb: bugfixes for multi-packet TXDMA support
We really want to use DMA mode 1 for all multi-packet transfers;
that's one IRQ on DMA completion, instead of one per packet.
There is an important issue with such transfers, especially on
the host side: when such transfers end with a full-size packet,
we must defer musb_dma_completion() calls until the FIFO empties.
Else we report URB completions too soon, and may clobber data in
the FIFO fifo when writing the next packet (losing data).
The Inventra DMA support uses DMA mode 1, but it ignores that
issue. The CPPI DMA support uses mode 0, but doesn't handle
its TXPKTRDY interrupts quite right either; it can get stale
"packet ready" interrupts, and report transfer completion too
early using slightly different code paths, also losing data.
So I'm solving it in a generic way -- by adding a sort of the
"interrupt filter" into musb_host_tx(), catching these cases
where a DMA completion IRQ doesn't suffice and removing some
needlessly controller-specific logic. When a TXDMA interrupt
happens and DMA request mode 1 is active, that filter resets
to mode 0 and defers URB completion processing until TXPKTRDY,
unless the FIFO is already empty. Related filtering logic in
Inventra and CPPI code gets removed.
Since it should be competely safe now to use the DMA request
mode 1 for host side transfers with the CPPI DMA controller,
set it in musb_h_tx_dma_start() ... now renamed (and shared).
[ dbrownell@users.sourceforge.net: don't introduce more
CamElCase; use more concise explanations ]
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
David Brownell [Fri, 27 Mar 2009 00:38:30 +0000 (17:38 -0700)]
USB: musb_host, fix ep0 fifo flushing
The MUSB host side can't share generic TX FIFO flush logic
with EP0; the EP0 TX status register bits are different
from those for other entpoints.
Resolve this issue by providing a new EP0-specific routine
to flush and reset the FIFO, which pays careful attention to
restrictions listed in the latest programmer's guide. This
gets rid of an open issue whereby the usbtest control write
test (#14) failed.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Alan Stern [Tue, 24 Mar 2009 14:39:13 +0000 (10:39 -0400)]
USB: usb-storage: augment unusual_devs entry for Simple Tech/Datafab
This patch (as1227) adds the MAX_SECTORS_64 flag to the unusual_devs
entry for the Simple Tech/Datafab controller. This fixes Bugzilla
#12882.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-and-tested-by: binbin <binbinsh@gmail.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
David Brownell [Fri, 27 Mar 2009 00:36:57 +0000 (17:36 -0700)]
USB: musb_host, minor enqueue locking fix (v2)
Someone noted that the enqueue path used an unlocked access
for usb_host_endpoint->hcpriv ... fix that, by being safe
and always accessing it under spinlock protection.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Oliver Neukum [Sat, 4 Apr 2009 07:25:15 +0000 (09:25 +0200)]
USB: fix oops in cdc-wdm in case of malformed descriptors
cdc-wdm needs to ignore extremely malformed descriptors.
Signed-off-by: Oliver Neukum <oliver@neukum.org>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Matthew Garrett [Sat, 4 Apr 2009 16:24:24 +0000 (17:24 +0100)]
USB: qcserial: Add extra device IDs
Add a set of device IDs from the Windows drivers. These aren't complete
(there's a couple of cases where a QDL device is identified without the
associated modem being identified), but it's better than the current
situation.
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Pascal Terjan [Tue, 7 Apr 2009 12:40:42 +0000 (14:40 +0200)]
USB: option: Add ids for D-Link DWM-652 3.5G modem
This patch allows D-Link DWM-652 3.5G modem to work.
It is an express card but was only tested with the provided usb adapter as I
don't have machines with express card connector.
/dev/ttyUSB{0,1,2} get created, and using comgt on ttyUSB1 works fine :
[root@plop tmp]# comgt -d /dev/ttyUSB1 -e
Enter PIN number: XXXX
Waiting for Registration..(120 sec max).
Registered on Home network: "Orange France",2
Signal Quality: 15,99
From: Pascal Terjan <pterjan@mandriva.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Peter Korsgaard [Wed, 25 Mar 2009 10:32:59 +0000 (11:32 +0100)]
USB: ftdi_sio: add vendor/project id for JETI specbos 1201 spectrometer
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Jonathan McDowell [Thu, 26 Mar 2009 07:45:27 +0000 (00:45 -0700)]
usb gadget: fix ethernet link reports to ethtool
The g_ether USB gadget driver currently decides whether or not there's a
link to report back for eth_get_link based on if the USB link speed is
set. The USB gadget speed is however often set even before the device is
enumerated. It seems more sensible to only report a "link" if we're
actually connected to a host that wants to talk to us. The patch below
does this for me - tested with the PXA27x UDC driver.
Signed-off-by: Jonathan McDowell <noodles@earth.li>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Linus Torvalds [Fri, 17 Apr 2009 17:08:13 +0000 (10:08 -0700)]
Merge branch 'for-linus' of git://git./linux/kernel/git/dtor/input
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: ads7846 - fix unsafe disable_irq
Input: mainstone-wm97xx - fix condition in pen_up
Input: pc110pad - remove unused variable dev
Input: bf54x-keys - remove depreciated IRQF_SAMPLE_RANDOM flag
Input: ad7877, ad7879 - remove depreciated IRQF_SAMPLE_RANDOM flag
Input: da9034-ts - make pen {down,up} events more reliable
Input: da9034-ts - add Bin Yang as co-author of the driver
Input: atkbd - add forced release keys quirk for Samsung NC20
Input: atkbd - add forced release keys quirk for Samsung Q45
Input: gameport - fix attach driver code
Input: hp_sdc_rtc should depend on serio
Input: wm97xx - don't specify IRQF_SAMPLE_RANDOM
Input: ads7846 - introduce platform specific way to synchronize sampling
Input: remove unnecessary synchronize_rcu() call
Input: i8042 - add a DMI table for the i8042.reset option
Input: i8042 - introduce a tougher reset
Linus Torvalds [Fri, 17 Apr 2009 16:59:27 +0000 (09:59 -0700)]
Get rid of final remnants of include/asm-$(ARCH)
This renames include/asm-h8300/timer.h into arch/h8300/include/asm: it
was left over just because that file had been created in the -mm tree
before the whole h8300 header subdirectory had been moved, and then got
merged in the old location afterwards.
(See commits
e0b0f9e4ead2468f84c26332ec42b118e76af572: "h8300: update
timer handler - new files" and
758db3f2118703a1e36374dae5d58bed963e7e0d:
"[h8300] move include/asm-h8300 to arch/h8300/include/asm" for details).
This also removes a left-over .gitignore file in include/asm-arm that
became stale when the ARM header files were moved (which happened in
multiple commits, just see "git log -- include/asm-arm" for details).
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Fri, 17 Apr 2009 16:57:17 +0000 (09:57 -0700)]
Merge branch 'for-linus' of git://linux-m32r.org/git/takata/linux-2.6_dev
* 'for-linus' of git://www.linux-m32r.org/git/takata/linux-2.6_dev:
m32r: move include/asm-m32r/* to arch/m32r/include/asm/
m32r: move include/asm-m32r headers to arch/m32r/include/asm
Linus Torvalds [Fri, 17 Apr 2009 16:56:11 +0000 (09:56 -0700)]
Merge branch 'x86-fixes-for-linus' of git://git./linux/kernel/git/tip/linux-2.6-tip
* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86: fix microcode driver newly spewing warnings
x86, PAT: Remove page granularity tracking for vm_insert_pfn maps
x86: disable X86_PTRACE_BTS for now
x86, documentation: kernel-parameters replace X86-32,X86-64 with X86
x86: pci-swiotlb.c swiotlb_dma_ops should be static
x86, PAT: Remove duplicate memtype reserve in devmem mmap
x86, PAT: Consolidate code in pat_x_mtrr_type() and reserve_memtype()
x86, PAT: Changing memtype to WC ensuring no WB alias
x86, PAT: Handle faults cleanly in set_memory_ APIs
x86, PAT: Change order of cpa and free in set_memory_wb
x86, CPA: Change idmap attribute before ioremap attribute setup
Matt Kraai [Fri, 17 Apr 2009 11:56:38 +0000 (12:56 +0100)]
AFS: Guard afs_file_readpage_read_complete() definition with CONFIG_AFS_FSCACHE
If CONFIG_AFS_FSCACHE is not defined, the following warning is displayed when
fs/afs/file.c is compiled:
fs/afs/file.c:111: warning: ‘afs_file_readpage_read_complete’ defined but not used
This occurs because all calls to this function are guarded by
CONFIG_AFS_FSCACHE. Thus, guard its definition as well.
Signed-off-by: Matt Kraai <kraai@ftbfs.org>
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Alan Cox [Fri, 17 Apr 2009 11:22:35 +0000 (12:22 +0100)]
vfat: Note the NLS requirement
Close bug #4754. Stop people getting into a situation where they can't
get their FAT filesystems to mount as they expect.
Signed-off-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
projects / openwrt / staging / blogic.git / log