Wolfgang Denk [Wed, 12 Oct 2011 20:42:28 +0000 (22:42 +0200)]
Merge branch 'master' of git://git.denx.de/u-boot-microblaze
* 'master' of git://git.denx.de/u-boot-microblaze:
microblaze: Copy bootfile from variables
microblaze: Fix unaligned.h for endians
microblaze: Initialize jumptable and console
microblaze: Support flashes on lower addresses
microblaze: Call common console_init_f initialization function
Michal Simek [Thu, 21 Jul 2011 07:47:15 +0000 (09:47 +0200)]
microblaze: Copy bootfile from variables
Setup bootfile.
Signed-off-by: Michal Simek <monstr@monstr.eu>
Michal Simek [Mon, 28 Feb 2011 09:14:33 +0000 (10:14 +0100)]
microblaze: Fix unaligned.h for endians
Also support little endian MB.
Signed-off-by: Michal Simek <monstr@monstr.eu>
Acked-by: Mike Frysinger <vapier@gentoo.org>
Michal Simek [Thu, 21 Jul 2011 08:30:42 +0000 (10:30 +0200)]
microblaze: Initialize jumptable and console
This changes were done to get support for netconsole.
Signed-off-by: Michal Simek <monstr@monstr.eu>
Michal Simek [Thu, 21 Jul 2011 09:01:58 +0000 (11:01 +0200)]
microblaze: Support flashes on lower addresses
Signed-off-by: Michal Simek <monstr@monstr.eu>
Michal Simek [Thu, 21 Jul 2011 07:52:25 +0000 (09:52 +0200)]
microblaze: Call common console_init_f initialization function
Calling console_init_f enables CTRL+C usage.
Signed-off-by: Michal Simek <monstr@monstr.eu>
Xie Xiaobo [Mon, 3 Oct 2011 19:54:21 +0000 (12:54 -0700)]
powerpc/mpc8536ds: Save the env variables to SDcard and SPI flash
MPC8536DS offer booting from SDcard or SPI flash. This patch defined that
u-boot can save the environment variables on SDcard or SPI flash when
booting from the related device. The Env parameter region and linux
kernel region have overlap in SPI-Flash, So change the Env param saving
address.
Signed-off-by: Xie Xiaobo <r63061@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Fanzc [Mon, 3 Oct 2011 19:18:42 +0000 (12:18 -0700)]
powerpc/mpc8536ds: Add USB support for MPC8536DS
Add EHCI controller and USB command definition.
Signed-off-by: Xie Xiaobo <r63061@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Tang Yuantian [Mon, 3 Oct 2011 19:18:41 +0000 (12:18 -0700)]
fsl_sata: Fix compile error when CONFIG_LBA48 is not defined
If CONFIG_LBA48 is not defined, the element lba48 of struct sata_dev_desc
is not avaible, and can't be used.
Signed-off-by: Tang Yuantian <b29983@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Xie Xiaobo [Mon, 3 Oct 2011 19:18:40 +0000 (12:18 -0700)]
powerpc/mpc8536ds: Invert SDHC_WP pin polarity
MPC8536 Rev 1.0 silicon have NMG_eSDHC118 erratum, so that the SDHC write
protected pin polarity does not follow the SD card standard in MPC8536
Rev 1.0 silicon.
The MPC8536DS board invert the SDHC_WP pin as a workaround. However, this
silicon erratum has been fixed in Rev 1.1, So need invert the SDHC_WP
polarity again when use the MPC8536 Rev1.1 and greater on MPC8536DS board.
Signed-off-by: Xie Xiaobo <r63061@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Xie Xiaobo [Mon, 3 Oct 2011 19:18:39 +0000 (12:18 -0700)]
powerpc/mpc8536ds: Add eSPI support for MPC8536DS
1. The SD_DATA[4:7] signals are shared with the SPI chip selects on 8536DS,
so don't set MPC85xx_PMUXCR_SD_DATA that config eSDHC data bus-width
to 4-bit and enable SPI signals.
2. Add eSPI controller and SPI-FLASH definition.
Signed-off-by: Xie Xiaobo <r63061@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
chenhui zhao [Tue, 6 Sep 2011 16:41:19 +0000 (16:41 +0000)]
powerpc/mpc8548cds: Update config file
- Increase the size of malloc space.
- Enable e1000 network card.
- Show pci devices on startup.
- Change the location of env address.
- Use hwconfig to turn off ECC by default.
[Kumar Gala] Fixed white space formating for CONFIG_EXTRA_ENV_SETTINGS
Signed-off-by: Zhao Chenhui <chenhui.zhao@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Becky Bruce [Tue, 4 Oct 2011 00:10:51 +0000 (19:10 -0500)]
powerpc/mpc86xx: Disable translation for BAT setup
We really shouldn't be overwriting bat registers with translation enabled,
especially when we're executing code using one of them for translating
the current instruction stream. Instead, disable address translation
while doing the final BAT setup.
In order to do this, setup_bats has to move back to asm code, because we
require translation to be enabled to have a stack for C code. The yucky
thing about that is that the assembler doesn't like ULL so we have to
switch to using HIGH/LOW pairs for physical addresses that are > 32 bits
in length.
Signed-off-by: Becky Bruce <beckyb@kernel.crashing.org>
Acked-by: York Sun <yorksun@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Becky Bruce [Tue, 4 Oct 2011 00:10:50 +0000 (19:10 -0500)]
powerpc/mpc8641hpcn: fix SRIO BAT config
There were duplicate (and conflicting) defines for the BATs used
to cover SRIO. Drop the bogus set.
Signed-off-by: Becky Bruce <beckyb@kernel.crashing.org>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Timur Tabi [Tue, 4 Oct 2011 21:44:43 +0000 (16:44 -0500)]
powerpc/85xx: fix null pointer dereference when init the SGMII TBI PHY
Function dtsec_configure_serdes() needs to know where the TBI PHY registers
are in order to configure SGMII for proper SerDes operation.
During SGMII initialzation, fm_eth_init_mac() passing NULL for 'phyregs'
when it called init_dtsec(), because it was believed that phyregs was not
used. In fact, it is used by dtsec_configure_serdes() to configure the TBI
PHY registers.
We also need to define the PHY registers in struct fm_mdio.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
York Sun [Mon, 3 Oct 2011 16:19:53 +0000 (09:19 -0700)]
powerpc/mpc8xxx: Merge entries in DDR speed table
It is not necessary to keep multiple entries for the same setting in DDR
speed tables. Merge them for smaller tables. Also restructure the tables
for smaller size. Cleanup some typedefs.
Enforce strict checking for speed table. If DIMM is running at higher than
known speed, try to use the highest speed setting. If rank is unknown, it
has to panic.
Removed ODT overriding for P2020DS as it is not necessary.
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Andy Fleming [Wed, 20 Apr 2011 23:41:17 +0000 (18:41 -0500)]
phylib: Work around bug in Teranetics PHY
The Teranetics PHY does not properly report the link state
for fiber connections. The new PHY code actually checked the link,
and so the FM driver would refuse to talk over a linkless PHY.
But the link may actually be up, so now we always report it as up
for fiber connections on the tn2020.
Signed-off-by: Andy Fleming <afleming@freescale.com>
Timur Tabi [Tue, 6 Sep 2011 14:36:06 +0000 (09:36 -0500)]
powerpc/85xx: CONFIG_ENABLE_36BIT_PHYS does not depend on CONFIG_PHYS_64BIT
The macro CONFIG_ENABLE_36BIT_PHYS is used to indicate that the given SOC is
capable of 36-bit physical addresses, even if such large addresses are not
used. On two boards, this macro was enabled only when building a 36-bit
image.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
York Sun [Fri, 16 Sep 2011 20:21:35 +0000 (13:21 -0700)]
powerpc/8xxx: Add support for interactive DDR programming interface
Interactive DDR debugging provides a user interface to view and modify SPD,
DIMM parameters, board options and DDR controller registers before DDR is
initialized. With this feature, developers can fine-tune DDR for board
bringup and other debugging without frequently having to reprogram the flash.
To enable this feature, define CONFIG_FSL_DDR_INTERACTIVE in board header
file and set an environment variable to activate it. Syntax:
setenv ddr_interactive on
After reset, U-boot prompts before initializing DDR controllers
FSL DDR>
The available commands are
print print SPD and intermediate computed data
reset reboot machine
recompute reload SPD and options to default and recompute regs
edit modify spd, parameter, or option
compute recompute registers from current next_step to end
next_step shows current next_step
help this message
go program the memory controller and continue with u-boot
The first command should be "compute", which reads data from DIMM SPDs and
board options, performs the calculation then stops before setting DDR
controller. A user can use "print" and "edit" commands to view and modify
anything. "Go" picks up from current step with any modification and
compltes the calculation then enables the DDR controller to continue u-boot.
"Recompute" does it over from fresh reading.
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Wolfgang Denk [Thu, 6 Oct 2011 07:22:52 +0000 (09:22 +0200)]
arm920t/s3c24x0/usb_ohci.c: fix warning: variable ... set but not used
Fix:
usb_ohci.c: In function 'dl_transfer_length':
usb_ohci.c:768:8: warning: variable 'tdINFO' set but not used [-Wunused-but-set-variable]
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Remy Bohmer <linux@bohmer.net>
Wolfgang Denk [Wed, 5 Oct 2011 21:11:19 +0000 (23:11 +0200)]
common/usb.c: fix warning: variable ... set but not used
Fix:
usb.c: In function 'usb_parse_config':
usb.c:331:17: warning: variable 'ch' set but not used [-Wunused-but-set-variable]
usb.c: In function 'usb_hub_port_connect_change':
usb.c:1123:29: warning: variable 'portchange' set but not used [-Wunused-but-set-variable]
usb.c: In function 'usb_hub_configure':
usb.c:1183:25: warning: variable 'hubsts' set but not used [-Wunused-but-set-variable]
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Remy Bohmer <linux@bohmer.net>
Acked-by: Remy Bohmer <linux@bohmer.net>
Wolfgang Denk [Wed, 5 Oct 2011 21:03:43 +0000 (23:03 +0200)]
drivers/usb/host/ohci-hcd.c: fix warning: variable ... set but not used
Fix:
ohci-hcd.c: In function 'dl_transfer_length':
ohci-hcd.c:968:8: warning: variable 'tdINFO' set but not used [-Wunused-but-set-variable]
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Remy Bohmer <linux@bohmer.net>
Acked-by: Remy Bohmer <linux@bohmer.net>
Wolfgang Denk [Wed, 5 Oct 2011 21:01:59 +0000 (23:01 +0200)]
common/cmd_usb.c: fix warning: variable ... set but not used
Fix:
cmd_usb.c: In function 'usb_show_tree_graph':
cmd_usb.c:284:29: warning: variable 'port' set but not used [-Wunused-but-set-variable]
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Remy Bohmer <linux@bohmer.net>
Acked-by: Remy Bohmer <linux@bohmer.net>
Wolfgang Denk [Wed, 5 Oct 2011 20:59:27 +0000 (22:59 +0200)]
drivers/net/smc91111.c: fix warning: variable ... set but not used
Fix:
smc91111.c: In function 'smc_phy_configure':
smc91111.c:1194:6: warning: variable 'failed' set but not used [-Wunused-but-set-variable]
smc91111.c:1190:7: warning: variable 'phyaddr' set but not used [-Wunused-but-set-variable]
Signed-off-by: Wolfgang Denk <wd@denx.de>
Wolfgang Denk [Wed, 5 Oct 2011 20:58:11 +0000 (22:58 +0200)]
fs/jffs2/jffs2_1pass.c: fix warning: variable ... set but not used
Fix:
jffs2_1pass.c: In function 'jffs2_1pass_read_inode':
jffs2_1pass.c:699:7: warning: variable 'ret' set but not used [-Wunused-but-set-variable]
jffs2_1pass.c: In function 'jffs2_1pass_build_lists':
jffs2_1pass.c:1578:14: warning: variable 'empty_start' set but not used [-Wunused-but-set-variable]
Signed-off-by: Wolfgang Denk <wd@denx.de>
Wolfgang Denk [Wed, 5 Oct 2011 20:48:12 +0000 (22:48 +0200)]
CFI: fix warning: variable ... set but not used
Fix:
cfi_mtd.c: In function 'cfi_mtd_init':
cfi_mtd.c:226:19: warning: variable 'mtd_list' set but not used [-Wunused-but-set-variable]
cfi_mtd.c: In function 'cfi_mtd_init':
cfi_mtd.c:225:6: warning: unused variable 'devices_found'
cfi_mtd.c: In function 'cfi_mtd_init':
cfi_mtd.c:226:19: warning: variable 'mtd_list' set but not used [-Wunused-but-set-variable]
[-Wunused-variable]
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Stefan Roese <sr@denx.de>
Acked-by: Stefan Roese <sr@denx.de>
Wolfgang Denk [Wed, 5 Oct 2011 20:44:43 +0000 (22:44 +0200)]
arch/arm/lib/board.c: fix warning: variable ... set but not used
Fix:
board.c:445:8: warning: variable 'bd' set but not used [-Wunused-but-set-variable]
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Albert ARIBAUD <albert.u.boot@aribaud.net>
Michael Walle [Fri, 7 Oct 2011 12:27:50 +0000 (12:27 +0000)]
netconsole: support packets longer than 512 bytes
Esp. while printing the environment the output is usually longer than 512
bytes. Instead of cutting the message, send multiple 512 bytes packets.
Signed-off-by: Michael Walle <michael@walle.cc>
Acked-by: Mike Frysinger <vapier@gentoo.org>
Che-liang Chiou [Thu, 6 Oct 2011 23:40:48 +0000 (23:40 +0000)]
cmd_time: add time command
The 'time' command runs and reports execution time of commands.
Sample usage:
--------------------
u-boot# time crc 0x1000 1000
CRC32 for
00001000 ...
00001fff ==>
ae94dc4b
time: 0.004 seconds, 4 ticks
--------------------
Signed-off-by: Che-Liang Chiou <clchiou@chromium.org>
Acked-by: Mike Frysinger <vapier@gentoo.org>
Wolfgang Denk [Sun, 9 Oct 2011 19:06:34 +0000 (21:06 +0200)]
README: fix typos and such.
Reported-by: Michael Jones <michael.jones@matrix-vision.de>
Signed-off-by: Wolfgang Denk <wd@denx.de>
Wolfgang Denk [Fri, 7 Oct 2011 07:58:21 +0000 (09:58 +0200)]
README: fix documentation of CONFIG_SHOW_BOOT_PROGRESS
Some previous changes added code right in the middle of the
description of CONFIG_SHOW_BOOT_PROGRESS. Move this text down.
Fix formatting while we are at it.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Wolfgang Denk [Fri, 7 Oct 2011 06:33:16 +0000 (08:33 +0200)]
common/image.c: remove duplicated IH_TYPE entries.
Also rearrange IH_TYPE table slightly.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Michal Simek [Sun, 25 Sep 2011 21:03:08 +0000 (21:03 +0000)]
serial: uartlite: Support for SERIAL_MULTI
Add support for SERIAL MULTI for uartlite.
Signed-off-by: Michal Simek <monstr@monstr.eu>
Stefan Roese [Fri, 7 Oct 2011 01:05:49 +0000 (01:05 +0000)]
ppc: Fix DBSR_IAx defines in <bedbug/regs.h>
While adding asm/cache.h to common.h for PPC targets, I got an
error about multiple definitions of some DBSR_ macros. While
scanning these defines, I noticed that some where defined not
correctly for all PPC variants. So I removed all unused defines,
and corrected the ones really used by bedbug (book-e vs. ppc40x).
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Wolfgang Denk <wd@denx.de>
Stefan Roese [Fri, 7 Oct 2011 01:05:34 +0000 (01:05 +0000)]
ppc: Include <asm/cache.h> in common.h
This is needed for the patch "cache: add default setting for
CONFIG_SYS_CACHELINE_SIZE" from Anton Staaf. As cache.h defines
CONFIG_SYS_CACHELINE_SIZE for PPC targets.
This will remove the following warnings/errors:
include/common.h:819:2: warning: #warning CONFIG_SYS_CACHELINE_SIZE not defined, using __BIGGEST_ALIGNMENT__
cache.c:33: error: '__BIGGEST_ALIGNMENT__' undeclared (first use in this function)
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Anton Staaf <robotboy@chromium.org>
Cc: Wolfgang Denk <wd@denx.de>
Lei Wen [Wed, 7 Sep 2011 18:11:19 +0000 (18:11 +0000)]
part: show efi partition name when print out partition info
Previous output:
Marvell>> mmc part
Partition Map for MMC device 1 -- Partition Type: EFI
Part Start LBA End LBA
gpt1 0x8C00 0xCBFF
gpt2 0xCC00 0x57BFF
gpt3 0x57C00 0xA2BFF
gpt4 0xA2C00 0xECBFDE
With the patch, the output becomes:
Marvell>> mmc part
Partition Map for MMC device 1 -- Partition Type: EFI
Part Name Start LBA End LBA
1 ramdisk 0x00008C00 0x0000CBFF
2 system 0x0000CC00 0x00057BFF
3 userdata 0x00057C00 0x000A2BFF
4 remaining 0x000A2C00 0x00ECBFDE
Signed-off-by: Lei Wen <leiwen@marvell.com>
Loïc Minier [Mon, 3 Oct 2011 09:57:12 +0000 (11:57 +0200)]
ublimage: NAND block size isn't set at build-time
mkimage's ublimage support can't depend of build-time board configs;
instead, this should be set in ublimage.cfg. Since currently no configs
in u-boot override the NAND block size, hardcode it as such in
ublimage.h to fix a build failure with "make tools":
gcc [...] -o ublimage.o ublimage.c -c
In file included from ublimage.c:37:0:
ublimage.h:31:20: fatal error: config.h: No such file or directory
Cc: Heiko Schocher <hs@denx.de>
Cc: patches@linaro.org
Signed-off-by: Loïc Minier <loic.minier@linaro.org>
Acked-by: Heiko Schocher <hs@denx.de>
Loïc Minier [Mon, 3 Oct 2011 09:57:11 +0000 (11:57 +0200)]
Safer timestamp_autogenerated.h generation
Generate timestamp_autogenerated.h as safely as version_autogenerated.h.
Cc: patches@linaro.org
Signed-off-by: Loïc Minier <loic.minier@linaro.org>
Acked-by: Mike Frysinger <vapier@gentoo.org>
Loïc Minier [Mon, 3 Oct 2011 09:57:10 +0000 (11:57 +0200)]
Build timestamp_autogenerated.h without config
Tools such as mkimage include version information but are
config-agnostic; build timestamp_autogenerated.h even when config.mk
isn't generated to fix "make tools" build failure:
gcc [...] -o mkimage.o mkimage.c -c
In file included from include/version.h:27:0, from mkimage.c:26:
include/timestamp.h:27:37: fatal error: timestamp_autogenerated.h: No
such file or directory
Cc: patches@linaro.org
Signed-off-by: Loïc Minier <loic.minier@linaro.org>
Acked-by: Mike Frysinger <vapier@gentoo.org>
Laurence Withers [Fri, 30 Sep 2011 12:09:39 +0000 (12:09 +0000)]
Tell git to ignore asm-offsets.s
The generated file asm-offsets.s may be found at various depths in the
arch subdirectories, so simply ignore it throughout the tree.
Signed-off-by: Laurence Withers <lwithers@guralp.com>
Acked-by: Mike Frysinger <vapier@gentoo.org>
Marek Vasut [Sun, 11 Sep 2011 17:56:19 +0000 (17:56 +0000)]
SPL: Make path to start.S configurable
Introduce CONFIG_SPL_START_S_PATH to configure path to start.S file. It's not
always fitting to use CPU's start.S .
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Kumar Gala [Mon, 3 Oct 2011 04:35:47 +0000 (04:35 +0000)]
cmd_sf: Fix compiler warning
cmd_sf.c: In function 'do_spi_flash':
cmd_sf.c:164:9: warning: 'skipped' may be used uninitialized in this function
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Acked-by: Mike Frysinger <vapier@gentoo.org>
Acked-by: Simon Glass <sjg@chromium.org>
Mike Frysinger [Sun, 2 Oct 2011 10:01:28 +0000 (10:01 +0000)]
board configs: drop NET_MULTI references
Now that none of the core checks CONFIG_NET_MULTI, there's not much point
in boards defining it. So scrub all references to it.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Mike Frysinger [Sun, 2 Oct 2011 10:01:27 +0000 (10:01 +0000)]
net: drop !NET_MULTI code
This is long over due. All but two net drivers have been converted, but
those have now been dropped.
The only thing left to do is actually delete all references to NET_MULTI
and code that is compiled when that is not defined. So here we scrub the
core code.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Mike Frysinger [Sun, 2 Oct 2011 10:01:26 +0000 (10:01 +0000)]
net: drop !NET_MULTI ns7520 driver
This driver was never converted to NET_MULTI, and no board uses it.
So punt it and be done.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Mike Frysinger [Sun, 2 Oct 2011 10:01:25 +0000 (10:01 +0000)]
net: drop !NET_MULTI bcm570x/tigon3 drivers
These drivers have never been converted to NET_MULTI, and they are only
used by one board (BMW). So drop the drivers until someone feels like
rewriting them for NET_MULTI support.
Rather than punting the BMW board completely, just disable net support
in its board config. Seems to build fine without it.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Mike Frysinger [Sat, 1 Oct 2011 10:15:04 +0000 (10:15 +0000)]
mkconfig: start deprecating Makefile config targets
Now that we've got boards.cfg and most people have converted over,
start warning people who have yet to so we can phase board configs
completely out of the Makefile.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Mike Frysinger [Mon, 3 Oct 2011 14:50:33 +0000 (14:50 +0000)]
image: push default arch values to arch headers
This pushes the ugly duplicated arch ifdef lists we maintain in various
image related files out to the arch headers themselves.
Acked-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Tested-by: Thomas Chou <thomas@wytron.com.tw>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Mike Frysinger [Sun, 25 Sep 2011 19:27:19 +0000 (19:27 +0000)]
MAKEALL: rename coldfire list to m68k to match arch
The m68k tree is the only one where `./MAKEALL <arch>` does not work.
So rename the existing coldfire list in the MAKEALL script to m68k, and
add an alias from coldfire to m68k. This makes scripting around MAKEALL
easier.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Stefano Babic [Thu, 15 Sep 2011 23:50:16 +0000 (23:50 +0000)]
mkimage: Add variable lenght header support
Some images have not a header of fix lenght. The patch will be
used for the generation of AIS images, because this header has
a variable lenght. The patch adds also the parameter "-s" (skip)
to not copy automatically the passed image file.
Signed-off-by: Stefano Babic <sbabic@denx.de>
Stefano Babic [Thu, 15 Sep 2011 23:50:15 +0000 (23:50 +0000)]
mkimage: ublimage must return if the header is not verified
Each image handler must return a not-zero velue if the
header is not recognized to allow the main program to
iterate to the next handler.
Signed-off-by: Stefano Babic <sbabic@denx.de>
CC: Heiko Schocher <hs@denx.de>
Acked-by: Heiko Schocher <hs@denx.de>
Valentin Longchamp [Mon, 12 Sep 2011 04:18:42 +0000 (04:18 +0000)]
km_arm: enable POST for these boards
The current km_arm boards have a Power-On test jumper. When this
jumper is set, this triggers some Power-On tests on the board.
This patch enables the support of this jumper for starting the
memory_regions test when the jumper is set.
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
Cc: Prafulla Wadaskar <prafulla@marvell.com>
Valentin Longchamp [Mon, 12 Sep 2011 04:18:41 +0000 (04:18 +0000)]
km_arm: change CONFIG_SYS_TEXT_BASE to end of RAM
This allows to test a larger part of the RAM in the memory tests.
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
Cc: Heiko Schocher <hs@denx.de>
Cc: Prafulla Wadaskar <prafulla@marvell.com>
Valentin Longchamp [Mon, 12 Sep 2011 04:18:40 +0000 (04:18 +0000)]
POST: add new memory regions test
This test is similar to the actual POST memory test but quicker and
far less complete. It checks the address and data lines and then only
tests some regularly placed sub regions of the RAM.
This can be useful when we want to test the RAM but we do not have enough
time to run the full memory test.
The POST memory test code was rearranged in order to avoid code duplication
between the two tests but the memory test functionnality remains the same.
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
Ackey-by: Mike Frysinger <vapier@gentoo.org>
Valentin Longchamp [Wed, 3 Aug 2011 02:37:03 +0000 (02:37 +0000)]
POST: drivers/memory.c coding style cleanup
This is needed for a further patch adding a new memory test.
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
Acked-by: Mike Frysinger <vapier@gentoo.org>
Valentin Longchamp [Wed, 3 Aug 2011 02:37:02 +0000 (02:37 +0000)]
POST: make env test flags fetching optional
Some boards have the environment variables defined in a slow EEPROM. post_run
accesses these environment variables to define which tests have to be run (in
post_get_flags). This is very slow before the code relocation on some boards
with a slow I2C EEPROM for environement variables.
This patch adds a config option to skip the fetching of the test flags in the
environment variables. The test flags assigned to the tests then only are the
ones statically defined for the test in post/tests.c.
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
Valentin Longchamp [Wed, 3 Aug 2011 02:37:01 +0000 (02:37 +0000)]
POST: add post_log_res field for post results in global data
The current post_log_word in global data is currently split into 2x
16 bits: half for the test start, half for the test success.
Since we alredy have more than 16 POST tests defined and more could
be defined, this may result in an overflow and the post_output_backlog
would not work for the tests defined further of these 16 positions.
An additional field is added to global data so that we can now support up
to 32 (depending of architecture) tests. The post_log_word is only used
to record the start of the test and the new field post_log_res for the
test success (or failure). The post_output_backlog is for this change
also adapted.
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
Valentin Longchamp [Fri, 2 Sep 2011 04:59:04 +0000 (04:59 +0000)]
POST: allow redefinition of post_word_load/store
The predefinde post_word_load/store functions do not fit all boards,
so we introduce a way to define post_word_load/store as externs in
post.h that then can be defined in board specific files. This is done
with the CONFIG_POST_EXTERNAL_WORD_FUNCS #define
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
Valentin Longchamp [Fri, 2 Sep 2011 04:59:03 +0000 (04:59 +0000)]
POST/arm: adaptations needed for POST on ARM to work
For post to run on ARM, 3 things are needed:
- post_log_word to be defined in gd
- a post.h include in arch/arm/lib/board.c
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
Cc: Mike Frysinger <vapier@gentoo.org>
Acked-by: Mike Frysinger <vapier@gentoo.org>
Graeme Russ [Thu, 1 Sep 2011 00:48:27 +0000 (00:48 +0000)]
console: Implement pre-console buffer
Allow redirection of console output prior to console initialisation to a
temporary buffer.
To enable this functionality, the board (or arch) must define:
- CONFIG_PRE_CONSOLE_BUFFER - Enable pre-console buffer
- CONFIG_PRE_CON_BUF_ADDR - Base address of pre-console buffer
- CONFIG_PRE_CON_BUF_SZ - Size of pre-console buffer (in bytes)
The pre-console buffer will buffer the last CONFIG_PRE_CON_BUF_SZ bytes
Any earlier characters are silently dropped.
Stefano Babic [Tue, 30 Aug 2011 00:52:43 +0000 (00:52 +0000)]
Makefile: remove mx31pdk exception
An entry in the main Makefile for the mx31pdk board is not
necessary, and the board is added to boards.cfg as all
other targets.
Signed-off-by: Stefano Babic <sbabic@denx.de>
CC: Wolfgang Denk <wd@denx.de>
Stefano Babic [Tue, 30 Aug 2011 00:52:42 +0000 (00:52 +0000)]
Makefile: drop imx31_phycore from general Makefile
Signed-off-by: Stefano Babic <sbabic@denx.de>
Stefano Babic [Mon, 29 Aug 2011 04:57:10 +0000 (04:57 +0000)]
Makefile: remove tx25 exception
An entry in the main Makefile for the tx25 board is not
necessary, and the board is added to boards.cfg as all
other targets.
Signed-off-by: Stefano Babic <sbabic@denx.de>
CC: Wolfgang Denk <wd@denx.de>
Marek Vasut [Wed, 5 Oct 2011 02:51:55 +0000 (02:51 +0000)]
PPC: Cleanup tqm8xx_pcmcia.c
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Tested-by: Wolfgang Denk <wd@denx.de>
Acked-by: Wolfgang Denk <wd@denx.de>
Wolfgang Denk [Wed, 5 Oct 2011 09:55:01 +0000 (09:55 +0000)]
TQM8xx: make room for growing code size due to I/O accessor cleanup
Commit "PPC: Cleanup tqm8xx_pcmcia.c" will clean up the PCMCIA code
to use I/O accessors instead of plain volatile pointer accesses.
This will result in about 300 byte bigger code. Fix custom linker
script to make room for this.
While we are at it, drop unmaintained u-boot.lds.debug linker script.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Marek Vasut <marek.vasut@gmail.com>
Tested-by: Wolfgang Denk <wd@denx.de>
Wolfgang Denk [Tue, 4 Oct 2011 20:20:25 +0000 (22:20 +0200)]
Merge branch 'master' of git://git.denx.de/u-boot-nand-flash
* 'master' of git://git.denx.de/u-boot-nand-flash:
PPC: Fix socrates NAND problem
PPC: Fix fsl_upm.c by renaming nand handling functions
NAND: Make page, erase, oob size available via cmd_nand
mtd: eLBC NAND: remove elbc_fcm_ctrl->oob_poi
NAND: Add -y option to nand scrub command
NAND: Add nand read.raw and write.raw commands
NAND: Really ignore bad blocks when scrubbing
spl, nand: add 4bit HW ecc oob first nand_read_page function
mxc_nand: fix a problem writing more than 32MB
mxc_nand: fixed some typos (cosmetic)
nand: increase chip_delay in mv kirkwood nand driver
Wolfgang Denk [Tue, 4 Oct 2011 20:08:13 +0000 (22:08 +0200)]
Merge branch 'master' of git://git.denx.de/u-boot-mpc85xx
* 'master' of git://git.denx.de/u-boot-mpc85xx:
powerpc/p3060: Add SoC related support for P3060 platform
powerpc/85xx: Add support for setting up RAID engine liodns on P5020
powerpc/85xx: Refactor some defines out of corenet_ds.h
fm-eth: Add ability for board code to disable a port
powerpc/mpc8548: Add workaround for erratum NMG_LBC103
powerpc/mpc8548: Add workaround for erratum NMG_DDR120
powerpc/mpc85xxcds: Fix PCI speed
powerpc/mpc8548cds: Fix booting message
powerpc/p4080: Add support for secure boot flow
powerpc/85xx: Add Secure Boot support on P1010RDB for NOR, NAND & SPIFLASH
powerpc/85xx: Add PBL & SECUREBOOT support on P3041/P5020DS boards
powerpc/p2041rdb: remove watch dog related codes
powerpc/p2041rdb: updated description of cpld command
powerpc/p2041rdb: add more ddr frequencies support
powerpc/p2041rdb: set sysclk according to status of physical switch SW1
powerpc/p2041rdb: update cpld reset command according to CPLD 2.0
powerpc/mpc8349emds: Migrate from spd_sdram to unified DDR driver
powerpc/mpc83xx: Migrate from spd_sdram to unified DDR driver
powerpc/mpc8xxx: Add DDR2 to unified DDR driver
powerpc/mpc8xxx: Fix picos_to_mclk() and get_memory_clk_period_ps()
powerpc/mpc8xxx: Add SPD EEPROM address for single controller 2 slots
powerpc/mpc8xxx: Fix DDR code for empty first DIMM slot and enable DQS_en
powerpc/85xx: Refactor P2041RDB to use common p_corenet files
powerpc/85xx: refactor common P-Series CoreNet files for FSL boards
powerpc/85xx: Enable CMD_REGINFO on corenet boards
powerpc/85xx: p2041rdb - Remove unused 'execute' perm in TLB entries
powerpc/85xx: Fix USB protocol definitions for P1020RDB
powerpc/corenet_ds: Use separated speed tables for UDIMM and RDIMM
powerpc/mpc8xxx: Move DDR RCW overriding to common code
powerpc/mpc8xxx: Extend CWL table
powerpc/85xx: Cleanup how SVR_MAJ() is defined on MPC8536
powerpc/85xx: Cleanup extern in corenet_ds board code
powerpc/p2041rdb: Add ethernet support on P2041RDB board
powerpc/85xx: Add networking support to P1023RDS
powerpc/hydra: Add ethernet support on P5020/P3041 DS boards
powerpc/85xx: Add FMan ethernet support to P4080DS
powerpc/85xx: Add support for FMan ethernet in Independent mode
powerpc/mpc8548cds: Cleanup mpc8548cds.c
powerpc/mp: add support for discontiguous cores
powerpc/85xx: corenet_ds - Remove unused 'execute' perm in TLB entries
fdt: Add new fdt_create_phandle helper
fdt: Rename fdt_create_phandle to fdt_set_phandle
powerpc/85xx: Fix compile warnings/errors if CONFIG_SYS_DPAA_FMAN isn't set
fsl_ifc: Add the workaround for erratum IFC A-003399(enabled on P1010)
powerpc/P1010: Add workaround for erratum P1010-
A003549 (related to IFC)
fsl_ifc: Add the workaround for erratum IFC-
A002769 (enable on P1010)
powerpc/85xx: Expanding the window of CCSRBAR in AS=1 from 4k to 1M
powerpc/85xx: Add NAND/NAND_SPL support to P1010RDB
nand: Freescale Integrated Flash Controller NAND support
powerpc/85xx: Add basic support for P1010RDB
powerpc/85xx: Add support for new P102x/P2020 RDB style boards
powerpc/85xx: relocate CCSR before creating the initial RAM area
powerpc/85xx: introduce and document CONFIG_SYS_CCSRBAR macros
powerpc/85xx: Enable internal USB UTMI PHY on p204x/p3041/p50x0
powerpc/85xx: Add ULPI and UTMI USB Phy support for P1010/P1014
Wolfgang Denk [Tue, 4 Oct 2011 20:06:06 +0000 (22:06 +0200)]
Merge branch 'master' of git://git.denx.de/u-boot-i2c
* 'master' of git://git.denx.de/u-boot-i2c:
I2C: mv_i2c: fix multi-bus init issue
I2C: mv_i2c: fix build issue when enable debug option
Wolfgang Denk [Tue, 4 Oct 2011 20:05:15 +0000 (22:05 +0200)]
Merge branch 'emaclite' of git://git.denx.de/u-boot-microblaze
* 'emaclite' of git://git.denx.de/u-boot-microblaze:
net: emaclite: Use dynamic allocation
net: emaclite: Remove baseaddress from xemaclite
net: emaclite: Use calloc instead of malloc
net: emaclite: Remove deviceid property
net: emaclite: Change driver name and add address
Wolfgang Denk [Tue, 4 Oct 2011 19:32:16 +0000 (21:32 +0200)]
Merge branch 'master' of git://git.denx.de/u-boot-microblaze
* 'master' of git://git.denx.de/u-boot-microblaze:
microblaze: Enable FDT/FIT support
microblaze: Remove address offset for uart16550
microblaze: Do not select NFS for platforms without ethernet
microblaze: Clean up reset asm code
microblaze: Save and restore first unused vector
microblaze: Setup MB vectors if feature is enable for u-boot
microblaze: Remove debug saving value
Wolfgang Denk [Tue, 4 Oct 2011 19:19:19 +0000 (21:19 +0200)]
Revert "GCC4.6: Convert various empty macros to inline functions"
This reverts commit
60ce53cf9f408d9ad721f8e7a87d6a564e6d5bac.
The commit causes build breakage for a number of boards. This results
from the fact that now the arguments of debug() actually get
referenced (even if there is hope that the compiler will optimize
away the debug() call). The obvious fix to that probem (change the
code to always declare the referenced variables and data structures)
increases the code size, and was this rejected. So it was decided to
revert this commit until a better solution is found.
Marek Vasut [Mon, 3 Oct 2011 22:56:09 +0000 (00:56 +0200)]
PPC: Fix socrates NAND problem
nand.c:36: error: static declaration of 'nand_read_buf' follows non-static declaration
/home/marex/u-boot/include/nand.h:139: error: previous declaration of 'nand_read_buf' was here
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Cc: Scott Wood <scottwood@freescale.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
Marek Vasut [Mon, 3 Oct 2011 22:56:07 +0000 (00:56 +0200)]
PPC: Fix fsl_upm.c by renaming nand handling functions
This avoids colision with nand subsystem's functions.
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Cc: Scott Wood <scottwood@freescale.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
Marek Vasut [Thu, 22 Sep 2011 01:57:26 +0000 (03:57 +0200)]
NAND: Make page, erase, oob size available via cmd_nand
The "nand info" and "nand device" now set shell/environment variables:
nand_writesize ... nand page size
nand_oobsize ..... nand oob area size
nand_erasesize ... nand erase block size
Also, the "nand info" command now displays this info.
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Cc: Scott Wood <scottwood@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Detlev Zundel <dzu@denx.de>
[scottwood@freescale.com: removed unnecessary memsets]
Signed-off-by: Scott Wood <scottwood@freescale.com>
mhench [Mon, 11 Jul 2011 12:29:43 +0000 (12:29 +0000)]
mtd: eLBC NAND: remove elbc_fcm_ctrl->oob_poi
The eLBC NAND driver currently follows up each program/write operation with a
read-back of the page, in order to [ostensibly] fill in ECC data for the
caller. However, the page address used for this read is always -1, so the read
will never work correctly. Remove this useless (and potentially problematic)
block of code.
v2: fix broken mailer
Signed-off-by: mhench <mhench@elutions.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
Marek Vasut [Tue, 13 Sep 2011 22:20:35 +0000 (00:20 +0200)]
NAND: Add -y option to nand scrub command
This allows the scrub command to scrub without asking the user if he really
wants to scrub the area. Useful in scripts.
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Cc: Scott Wood <scottwood@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Detlev Zundel <dzu@denx.de>
Acked-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Scott Wood <scottwood@freescale.com>
Marek Vasut [Fri, 23 Sep 2011 13:43:10 +0000 (15:43 +0200)]
NAND: Add nand read.raw and write.raw commands
These commands should work around various "hardware" ECC and BCH methods.
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Cc: Scott Wood <scottwood@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Detlev Zundel <dzu@denx.de>
[scottwood@freescale.com: s/write the page/access the page/]
Signed-off-by: Scott Wood <scottwood@freescale.com>
Marek Vasut [Mon, 12 Sep 2011 04:04:06 +0000 (06:04 +0200)]
NAND: Really ignore bad blocks when scrubbing
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Cc: Scott Wood <scottwood@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Detlev Zundel <dzu@denx.de>
[scottwood@freescale.com: use chip instead of redundant priv_nand]
Signed-off-by: Scott Wood <scottwood@freescale.com>
Heiko Schocher [Sat, 16 Jul 2011 00:06:49 +0000 (00:06 +0000)]
spl, nand: add 4bit HW ecc oob first nand_read_page function
Signed-off-by: Heiko Schocher <hs@denx.de>
cc: Scott Wood <scottwood@freescale.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
Helmut Raiger [Wed, 6 Jul 2011 17:04:41 +0000 (19:04 +0200)]
mxc_nand: fix a problem writing more than 32MB
When writing 0x4000 to the unlockend_blkaddr register, large writes to
a 2k page NAND sometimes fail. The current kernel driver writes 0xFFFF
to this register for V2 of the nand controller.
However on an i.MX31 this also fixes writes larger than 32MB.
The datasheet is very unspecific, but (0x4000=16384)*2000
roughly fits the limits we're encountering with NAND writes.
This problem might be NAND chip specific.
Signed-off-by: Helmut Raiger <helmut.raiger@hale.at>
Signed-off-by: Scott Wood <scottwood@freescale.com>
Helmut Raiger [Wed, 6 Jul 2011 07:40:28 +0000 (09:40 +0200)]
mxc_nand: fixed some typos (cosmetic)
Signed-off-by: Helmut Raiger <helmut.raiger@hale.at>
Signed-off-by: Scott Wood <scottwood@freescale.com>
Stefan Bigler [Mon, 18 Jul 2011 13:25:11 +0000 (15:25 +0200)]
nand: increase chip_delay in mv kirkwood nand driver
The new SAMSUNG NAND Flash K9F1G08U0D require a bigger chip_delay.
The Data Transfer from Cell to Register is >= 35us. Other Vendors
and older chips normally use >= 25us. To have enough margin 40us
is selected.
Signed-off-by: Stefan Bigler <stefan.bigler@keymile.com>
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
cc: Prafulla Wadaskar <prafulla@marvell.com>
cc: Stefan Roese <sr@denx.de>
Signed-off-by: Scott Wood <scottwood@freescale.com>
Shengzhou Liu [Wed, 31 Aug 2011 09:48:18 +0000 (17:48 +0800)]
powerpc/p3060: Add SoC related support for P3060 platform
Add P3060 SoC specific information:cores setup, LIODN setup, etc
The P3060 SoC combines six e500mc Power Architecture processor cores with
high-performance datapath acceleration architecture(DPAA), CoreNet fabric
infrastructure, as well as network and peripheral interfaces.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Kumar Gala [Sat, 10 Sep 2011 15:44:13 +0000 (10:44 -0500)]
powerpc/85xx: Add support for setting up RAID engine liodns on P5020
Add support for Job Queue/Ring LIODN for the RAID Engine on P5020. Each
Job Queue/Ring combo needs one id assigned for a total of 4 (2 JQs/2
Rings per JQ). This just handles RAID Engine in non-DPAA mode.
Signed-off-by: Santosh Shukla <santosh.shukla@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Kumar Gala [Wed, 31 Aug 2011 14:50:13 +0000 (09:50 -0500)]
powerpc/85xx: Refactor some defines out of corenet_ds.h
Move some SoC/board specific defines out of corenet_ds.h and into the
corresponding P3041DS/P4080DS/P5020.h.
We moved CONFIG_MMC, CONFIG_PCIE3, & CONFIG_FSL_NGPIXIS because the P3060
SoC/reference board does not have these devices and it will share the same
board code.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Kumar Gala [Wed, 14 Sep 2011 17:01:35 +0000 (12:01 -0500)]
fm-eth: Add ability for board code to disable a port
The SoC configuration may have more ports enabled than a given board
actually can utilize. Add a routinue that allows the board code to
disable a port that it knows isn't being used.
fm_disable_port() needs to be called before cpu_eth_init().
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Kumar Gala [Mon, 3 Oct 2011 13:37:57 +0000 (08:37 -0500)]
powerpc/mpc8548: Add workaround for erratum NMG_LBC103
The erratum NMG_LBC103 is LBIU3 in MPC8548 errata document.
Any local bus transaction may fail during LBIU resynchronization
process when the clock divider [CLKDIV] is changing. Ensure there
is no transaction on the local bus for at least 100 microseconds
after changing clock divider LCRR[CLKDIV].
Refer to the erratum LBIU3 of mpc8548.
Signed-off-by: Zhao Chenhui <chenhui.zhao@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Kumar Gala [Fri, 16 Sep 2011 14:54:30 +0000 (09:54 -0500)]
powerpc/mpc8548: Add workaround for erratum NMG_DDR120
Erratum NMG_DDR120 (DDR19 in MPC8548 errata document) applies to some
early version silicons. The default settings of the DDR IO receiver
biasing may not work at cold temperature. When a failure occurs,
a DDR input latches an incorrect value. The workaround will set the
receiver to an acceptable bias point.
Signed-off-by: Gong Chen
Signed-off-by: Zhao Chenhui <chenhui.zhao@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
chenhui zhao [Thu, 15 Sep 2011 06:52:34 +0000 (14:52 +0800)]
powerpc/mpc85xxcds: Fix PCI speed
The CDS uses PCICLK as SYSCLK. The PCICLK should be 33333333Hz or 66666666Hz.
Signed-off-by: Ebony Zhu <ebony.zhu@freescale.com>
Signed-off-by: Zhao Chenhui <chenhui.zhao@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
chenhui zhao [Tue, 6 Sep 2011 16:41:14 +0000 (16:41 +0000)]
powerpc/mpc8548cds: Fix booting message
Align the output for PCI. Replace "PCI" with "PCI1".
Signed-off-by: Zhao Chenhui <chenhui.zhao@freescale.com>
Ruchika Gupta [Wed, 15 Dec 2010 17:02:08 +0000 (17:02 +0000)]
powerpc/p4080: Add support for secure boot flow
Pre u-boot Flow:
1. User loads the u-boot image in flash
2. PBL/Configuration word is used to create LAW for Flash at 0xc0000000
(Please note that ISBC expects all these addresses, images to be
validated, entry point etc within 0 - 3.5G range)
3. ISBC validates the u-boot image, and passes control to u-boot
at 0xcffffffc.
Changes in u-boot:
1. Temporarily map CONFIG_SYS_MONITOR_BASE to the 1M
CONFIG_SYS_PBI_FLASH_WINDOW in AS=1.
(The CONFIG_SYS_PBI_FLASH_WINDOW is the address map for the flash
created by PBL/configuration word within 0 - 3.5G memory range. The
u-boot image at this address has been validated by ISBC code)
2. Remove TLB entries for 0 - 3.5G created by ISBC code
3. Remove the LAW entry for the CONFIG_SYS_PBI_FLASH_WINDOW created by
PBL/configuration word after switch to AS = 1
Signed-off-by: Ruchika Gupta <ruchika.gupta@freescale.com>
Signed-off-by: Kuldip Giroh <kuldip.giroh@freescale.com>
Acked-by: Wood Scott-B07421 <B07421@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Ruchika Gupta [Thu, 9 Jun 2011 03:52:48 +0000 (22:52 -0500)]
powerpc/85xx: Add Secure Boot support on P1010RDB for NOR, NAND & SPIFLASH
Signed-off-by: Ruchika Gupta <ruchika.gupta@freescale.com>
Signed-off-by: Kuldip Giroh <kuldip.giroh@freescale.com>
Kumar Gala [Sat, 9 Apr 2011 18:43:55 +0000 (13:43 -0500)]
powerpc/85xx: Add PBL & SECUREBOOT support on P3041/P5020DS boards
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Shaohui Xie [Fri, 23 Sep 2011 01:18:12 +0000 (09:18 +0800)]
powerpc/p2041rdb: remove watch dog related codes
CPLD 2.2 removed board watch dog support due to the limitation of CPLD
capacity after adding all the requested features, such as switch overriding.
There is no pin-compatible upgrade part available for current PCB design.
So remove codes related to it.
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Shaohui Xie [Thu, 22 Sep 2011 09:27:29 +0000 (17:27 +0800)]
powerpc/p2041rdb: updated description of cpld command
According to CPLD 2.2, the default configuration is changed, so updated the
description of CPLD command, otherwise it will confusing.
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Shaohui Xie [Thu, 22 Sep 2011 03:46:12 +0000 (11:46 +0800)]
powerpc/p2041rdb: add more ddr frequencies support
This table covers DDR frequencies from 666 to 1666. Frequencies 666, 833,
1000, 1066 and 1333 were verified on this board with SO-DIMM
(UG51U6400N8SU-ACF).
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Shaohui Xie [Tue, 13 Sep 2011 09:55:11 +0000 (17:55 +0800)]
powerpc/p2041rdb: set sysclk according to status of physical switch SW1
P2041RDB supports 3 sysclk frequencies, it's selected by SW1[6~8],
software need to read the SW1 status to decide what the sysclk needs.
SW1[8~6] : frequency
0 0 1 : 83.3MHz
0 1 0 : 100MHz
others: 66.667MHz
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Shaohui Xie [Tue, 13 Sep 2011 09:51:39 +0000 (17:51 +0800)]
powerpc/p2041rdb: update cpld reset command according to CPLD 2.0
CPLD 2.0 provides a new register which bit[0] is set to '1' will reset
board with initializing the CPLD registers to default values. And add
bit[6] of register at offset 0x5 to use to enable flash bank selection.
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Lei Wen [Fri, 30 Sep 2011 05:44:12 +0000 (05:44 +0000)]
I2C: mv_i2c: fix multi-bus init issue
When enable the multi-bus, the current_bus is not inited in the original
implementation, which make the i2c operation unpredicatable.
Signed-off-by: Lei Wen <leiwen@marvell.com>
Lei Wen [Fri, 30 Sep 2011 05:43:48 +0000 (05:43 +0000)]
I2C: mv_i2c: fix build issue when enable debug option
When DEBUG_I2C is open, the following build issue would shows up.
mv_i2c.c: In function 'i2c_transfer':
mv_i2c.c:257: error: 'ISR' undeclared (first use in this function)
mv_i2c.c:257: error: (Each undeclared identifier is reported only once
mv_i2c.c:257: error: for each function it appears in.)
Signed-off-by: Lei Wen <leiwen@marvell.com>