Antonio Flores [Mon, 2 Sep 2024 02:24:35 +0000 (22:24 -0400)]
rockchip: rework LED configurations for the NanoPi R6C/R6S
This commits fixes the LED on the NanoPi R6 series
after changes in the DTS
https://lore.kernel.org/all/
20240612205056.397204-4-seb-dev@mail.de
Reported by Github user: gSpotx2f
Signed-off-by: Antonio Flores <antflores627@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16275
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Antonio Flores [Fri, 30 Aug 2024 11:41:45 +0000 (07:41 -0400)]
uboot-rockchip: patches: add version when were applied upstream
This patch add a version to uboot patches to help identify in
futures updates when they were upstreamed.
Signed-off-by: Antonio Flores <antflores627@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16275
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Antonio Flores [Tue, 27 Aug 2024 21:16:02 +0000 (17:16 -0400)]
rockchip: fixes and improve for NanoPi R6 series
Improvement and fixes for the nanopi r6 series, pending on the kernel mailing list
https://lore.kernel.org/all/
20240612205056.397204-1-seb-dev@mail.de
Signed-off-by: Antonio Flores <antflores627@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16275
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Antonio Flores [Tue, 27 Aug 2024 20:36:02 +0000 (16:36 -0400)]
rockchip: add FriendlyElec NanoPi R6C
Hardware Spec
-SoC: Rockchip RK3588S
CPU: Quad-core ARM Cortex-A76(up to 2.4GHz) and quad-core Cortex-A55 CPU (up to 1.8GHz)
GPU: Mali-G610 MP4, compatible with OpenGLES 1.1, 2.0, and 3.2, OpenCL up to 2.2 and Vulkan1.2
VPU: 8K@60fps H.265 and VP9 decoder, 8K@30fps H.264 decoder, 4K@60fps AV1 decoder, 8K@30fps H.264 and H.265
NPU: 6TOPs, supports INT4/INT8/INT16/FP16
-RAM: 64-bit 4GB/8GB LPDDR4X at 2133MHz
-Flash: 32GB/None eMMC, at HS400 mode
-Ethernet: one Native Gigabit Ethernet, and one PCIe 2.5G Ethernet
-USB: one USB 3.0 Type-A and one USB 2.0 Type-A
-PCIe: one M.2 Key M connector with PCIe 2.1 x1
-HDMI:
compatible with HDMI2.1, HDMI2.0, and HDMI1.4 operation
support up to 7680x4320@60Hz
Support RGB/YUV(up to 10bit) format
-microSD: support up to SDR104 mode
-GPIO:
30-pin 2.54mm header connector
up to 1x SPI, 3x UARTs, 3x I2Cs, 2x SPDIFs, 1x I2Ss, 3x PWMs, 20x GPIOs
-Debug: UART via 3-Pin 2.54mm header, or on-board USB-C to UART
-LEDs: 4 x GPIO Controlled LED (SYS, WAN, LAN, LED1)
-others:
2 Pin 1.27/1.25mm RTC battery input connector for low power RTC IC HYM8563TS
MASK button for eMMC update
one user button
-Power supply: USB-C, support PD, 5V/9V/12V/20V input
-PCB: 8 Layer, 62x90x1.6mm
-Ambient Operating Temperature: 0℃ to 70℃
Installation:
Uncompress the OpenWrt sysupgrade and write image to the SD card using dd (dd if=*.img of=/*)
eMMC Installation:
Boot from the SD card
Uncompress the OpenWrt sysupgrade image
fash to eMMC : dd if=*.img of=/dev/mmcblk1
sync
remove SD card
reboot
Signed-off-by: Antonio Flores <antflores627@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16275
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Antonio Flores [Tue, 13 Aug 2024 02:15:28 +0000 (22:15 -0400)]
uboot-rockchip: add FriendlyElec NanoPi R6C
1- The NanoPi R6C is a SBC by FriendlyElec based on the Rockchip RK3588s.
It comes with 4GB or 8GB of RAM, a microSD card slot, optional 32GB eMMC
storage, one M.2 M-Key connector, one RTL8211F 1GbE and one RTL8125
2.5GbE Ethernet port, one USB 2.0 Type-A and one USB 3.0 Type-A port, a
HDMI port, a 30-pin GPIO header as well as multiple buttons and LEDs.
2- Renamed 000-backport-upstream-dts-sync.patch -> 000-v2024.10-rc1-backport-upstream-dts-sync.patch
to add the version when was applied upstream
Signed-off-by: Antonio Flores <antflores627@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16275
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Yegor Yefremov [Thu, 19 Sep 2024 12:11:45 +0000 (14:11 +0200)]
tools/meson: update to 1.5.1
Changelog: https://mesonbuild.com/Release-notes-for-1-5-0.html
Signed-off-by: Yegor Yefremov <yegorslists@googlemail.com>
Link: https://github.com/openwrt/openwrt/pull/16425
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Aleksandr V. Piskunov [Tue, 16 Jul 2024 13:58:11 +0000 (16:58 +0300)]
6in4: add 'nohostroute' option
Same as 'nohostroute' option for GRE tunnels (commit
0f8b9addfc)
and IPIP tunnels (commit
46ce629fe0)
Signed-off-by: Aleksandr V. Piskunov <aleksandr.v.piskunov@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/15961
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Aleksandr V. Piskunov [Tue, 16 Jul 2024 13:44:35 +0000 (16:44 +0300)]
6in4: Support fqdn as remote tunnel endpoint
Same as fqdn support in GRE (commit
a79f3d11b3) and IPIP (commit
311682905e)
Signed-off-by: Aleksandr V. Piskunov <aleksandr.v.piskunov@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/15961
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Aleksandr V. Piskunov [Tue, 16 Jul 2024 13:39:17 +0000 (16:39 +0300)]
6in4: allow specifying tunnel device name
Accept 'device' option, allowing to specify custom l3 device name,
instead of default autogenerated one (prefix "6in4-" + interface name)
Signed-off-by: Aleksandr V. Piskunov <aleksandr.v.piskunov@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/15961
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Pawel Dembicki [Mon, 9 Sep 2024 10:35:40 +0000 (12:35 +0200)]
ls-mc: bump to 10.39.0
Update ls-mc to latest 10.39.0 version.
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16360
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Pawel Dembicki [Mon, 9 Sep 2024 10:35:00 +0000 (12:35 +0200)]
ls-dpl: bump to 10.39.0
Update ls-dpl to latest 10.39.0 version.
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16360
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Pawel Dembicki [Mon, 9 Sep 2024 10:34:09 +0000 (12:34 +0200)]
ls-rcw: Bump to lf-6.6.23-2.0.0
Bump ls-rcw package to lf-6.6.23-3.0.0.
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16360
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Pawel Dembicki [Mon, 9 Sep 2024 10:32:56 +0000 (12:32 +0200)]
restool: bump to lf-6.6.23-2.0.0
This commit bumps restool layerscape package to lf-6.6.23-2.0.0 version.
Patch was refreshed.
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16360
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Pawel Dembicki [Mon, 9 Sep 2024 10:15:29 +0000 (12:15 +0200)]
uboot-layerscape: bump to lf-6.6.23-2.0.0
This commit bumps u-boot layerscape package to lf-6.6.23-2.0.0 version.
Manually rebased:
0900-layerscape-adjust-LS1021A-IOT-config-for-OpenWrt.patch
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16360
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Pawel Dembicki [Mon, 9 Sep 2024 10:06:42 +0000 (12:06 +0200)]
tfa-layerscape: Bump to lf-6.6.23-2.0.0
This commit bumps tfa-layerscape package to version lf-6.6.23-2.0.0
Manually rebased:
001-fiptool-hostbuild-fixes.patch
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16360
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Tianling Shen [Fri, 6 Sep 2024 07:27:25 +0000 (15:27 +0800)]
rockchip: backport upstream updates for nanopc t6
Backport ir-receiver/minipcie/poweroff/spi/usb-c support and other
minor fixes for the NanoPC T6 board.
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
Link: https://github.com/openwrt/openwrt/pull/16443
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Aleksey Vasilenko [Sat, 21 Sep 2024 14:00:39 +0000 (17:00 +0300)]
build: remove ac_cv_header_netinet_sctp_h=no from pre-cached variables
We have <netinet/sctp.h> header in lksctp-tools package,
but having this var set to 'no' prevents package's configure
to detect it.
Signed-off-by: Aleksey Vasilenko <aleksey.vasilenko@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16441
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Mieczyslaw Nalewaj [Thu, 5 Sep 2024 07:37:56 +0000 (09:37 +0200)]
ramips: TP-Link EC220-G5 v2: swap WLAN leds assignment
Swap incorrect WLAN leds assignment between WLAN 2.4 and 5 GHz for TP-Link EC220-G5 v2
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Link: https://github.com/openwrt/openwrt/pull/16331
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
INAGAKI Hiroshi [Mon, 16 Sep 2024 20:43:58 +0000 (05:43 +0900)]
mvebu: improve sysupgrade for FortiGate/FortiWiFi devices
Update sysupgrade script (fortinet.sh) for Fortinet devices in
mvebu/cortexa9 and fix the following issues,
- Some individuals of FortiGate/FortiWiFi 30E/5xE devices has wrong
kernel/rootfs offsets in "firmware-info" partition and they are not
updated with the current sysupgrade script for Fortinet devices
(fortinet.sh).
As a result, the bootloader tries to load kernel data from the wrong
address and boot with it after OpenWrt installation.
The new script handles offsets in addition to length values.
and improve the following points.
- Only 2 bytes are handled with the current sysupgrade script
(fortinet.sh) for kernel/rootfs length. The new script handles 4 bytes
instead.
- The image names of image0/image1 are not handled and not updated when
sysupgrade. The new sysupgrade script handles it and update to
"<dist> <version> <revision>" if firmware metadata is available.
(ex.: "OpenWrt SNAPSHOT r27440-
25384026")
log of new sysupgrade script (fortinet.sh):
Tue Sep 17 10:29:16 UTC 2024 upgrade: Performing system upgrade...
Image Index: 0
Image Name : "OpenWrt SNAPSHOT r27440-
25384026"
--> "OpenWrt SNAPSHOT r27441-
b3a0806a05"
kernel:
old: 0x003c4e00@0x00200000
new: 0x003c4e00@0x00200000
rootfs:
old: 0x005c0200@0x00800000
new: 0x005c0200@0x00800000
Unlocking kernel ...
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16409
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
INAGAKI Hiroshi [Sat, 14 Sep 2024 06:38:46 +0000 (15:38 +0900)]
mvebu: update triggers of "SPEED" LEDs on FortiGate/FortiWiFi devices
The mdio bus number of mv88e6xxx was changed to '0' from '1' and the
"mv88e6xxx-1:<addr>:<speed>" triggers are unavailable now.
Update triggers for "SPEED" LEDs to make working that LEDs again.
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16409
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
INAGAKI Hiroshi [Sat, 14 Sep 2024 06:37:02 +0000 (15:37 +0900)]
mvebu: fix "compatible" of regulator for FortiGate/FortiWiFi devices
The driver for fixed voltage regulater uses "regulator-fixed" for
compatible string, not "fixed-regulator".
Fixes: 102dc5a625 ("mvebu: add support for FortiGate 50E")
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16409
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Hauke Mehrtens [Sun, 22 Sep 2024 12:07:26 +0000 (14:07 +0200)]
ramips: dna_valokuitu-plus-ex400: build sysupgrade.bin
Rename the sysupgrade.tar step to sysupgrade.bin. The sysupgrade.tar is
used in other places and we prefer a sysupgrade.bin instead.
Fixes: fea2264d9fdd ("ramips: mt7621: Add DNA Valokuitu Plus EX400")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Hauke Mehrtens [Sun, 22 Sep 2024 12:03:22 +0000 (14:03 +0200)]
ramips: tp-link er605-v2: Remove sysupgrade-tar image
The sysupgrade-tar image build is not defined for this target, do not
add a build instruction for it. The build system will use the definition
from the dna_valokuitu-plus-ex400 board and the build will fail.
This fixes the build of the ramips target.
Fixes: 665c2154ef12 ("ramips: add basic support for tp-link er605-v2")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Mieczyslaw Nalewaj [Sun, 22 Sep 2024 06:29:56 +0000 (08:29 +0200)]
include: remove kernel 6.1 version file
Remove unused kernel 6.1 version file.
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Link: https://github.com/openwrt/openwrt/pull/16450
Signed-off-by: Robert Marko <robimarko@gmail.com>
Felix Fietkau [Wed, 18 Sep 2024 16:26:45 +0000 (18:26 +0200)]
hostapd: fix OWE ssid update on configuration changes
Refresh OWE transition IEs on updating BSS interfaces
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Felix Fietkau [Sat, 21 Sep 2024 18:30:01 +0000 (20:30 +0200)]
wpa_supplicant: fix num_global_macaddr handling
Pass num_global_macaddr via ubus in the top level config_set call
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Felix Fietkau [Sat, 21 Sep 2024 18:13:51 +0000 (20:13 +0200)]
hostapd: fix num_global_macaddr and mbssid config handling
Store the config values in the correct field and apply them on restart too
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Felix Fietkau [Wed, 18 Sep 2024 16:10:25 +0000 (18:10 +0200)]
hostapd: fold extra APuP patches into main patch + src/
Simplifies maintenance
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Felix Fietkau [Wed, 17 Jul 2024 16:33:43 +0000 (18:33 +0200)]
hostapd: improve ucode bss notifications
Reduce code duplication, add extra callback for bss create
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Felix Fietkau [Sat, 21 Sep 2024 16:28:40 +0000 (18:28 +0200)]
netifd: update to Git HEAD (2024-09-21)
24f9a93a9559 interface: fix regression on adding hotplug devices to interfaces
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Ryan Salsbury [Tue, 17 Sep 2024 00:49:21 +0000 (17:49 -0700)]
ath79: fix I2C pins on GL-AR750
Change I2C pin flags to GPIO_ACTIVE_HIGH and change SDA to GPIO1.
On my late production GL-AR750 (purchased 2024):
SCL = GPIO16
SDA = GPIO1
Bug report:
I2C bus doesn't work in GL-AR750
https://github.com/openwrt/openwrt/issues/16319
Signed-off-by: Ryan Salsbury <ryanrs@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16406
Signed-off-by: Robert Marko <robimarko@gmail.com>
Robert Marko [Sat, 21 Sep 2024 11:31:28 +0000 (13:31 +0200)]
config: build: make STRIP_KERNEL_EXPORTS depend on BROKEN
STRIP_KERNEL_EXPORTS is currently broken on kernel 6.6 and since this
is the only kernel currently supported, we should rather make it depend
on BROKEN instead of a kernel version until its fixed.
Link: https://github.com/openwrt/openwrt/pull/16440
Signed-off-by: Robert Marko <robimarko@gmail.com>
Antonio Flores [Wed, 18 Sep 2024 15:06:12 +0000 (11:06 -0400)]
mac80211: CVE-2024-46760: rtw88: schedule rx work after everything is set up
link: https://lore.kernel.org/all/2024091842-CVE-2024-46760-1eb3@gregkh
Description
===========
In the Linux kernel, the following vulnerability has been resolved:
wifi: rtw88: usb: schedule rx work after everything is set up
Right now it's possible to hit NULL pointer dereference in
rtw_rx_fill_rx_status on hw object and/or its fields because
initialization routine can start getting USB replies before
rtw_dev is fully setup.
The stack trace looks like this:
rtw_rx_fill_rx_status
rtw8821c_query_rx_desc
rtw_usb_rx_handler
...
queue_work
rtw_usb_read_port_complete
...
usb_submit_urb
rtw_usb_rx_resubmit
rtw_usb_init_rx
rtw_usb_probe
So while we do the async stuff rtw_usb_probe continues and calls
rtw_register_hw, which does all kinds of initialization (e.g.
via ieee80211_register_hw) that rtw_rx_fill_rx_status relies on.
Fix this by moving the first usb_submit_urb after everything
is set up.
For me, this bug manifested as:
[ 8.893177] rtw_8821cu 1-1:1.2: band wrong, packet dropped
[ 8.910904] rtw_8821cu 1-1:1.2: hw->conf.chandef.chan NULL in rtw_rx_fill_rx_status
because I'm using Larry's backport of rtw88 driver with the NULL
checks in rtw_rx_fill_rx_status.
The Linux kernel CVE team has assigned CVE-2024-46760 to this issue.
Affected and fixed versions
===========================
Fixed in 6.6.51 with commit
c83d464b82a8
Fixed in 6.10.10 with commit
25eaef533bf3
Fixed in 6.11 with commit
adc539784c98
Please see https://www.kernel.org for a full list of currently supported
kernel versions by the kernel community.
Unaffected versions might change over time as fixes are backported to
older supported kernel versions. The official CVE entry at
https://cve.org/CVERecord/?id=CVE-2024-46760
will be updated if fixes are backported, please check that for the most
up to date information about this issue.
Affected files
==============
The file(s) affected by this issue are:
drivers/net/wireless/realtek/rtw88/usb.c
Mitigation
==========
The Linux kernel CVE team recommends that you update to the latest
stable kernel version for this, and many other bugfixes. Individual
changes are never tested alone, but rather are part of a larger kernel
release. Cherry-picking individual commits is not recommended or
supported by the Linux kernel community at all. If however, updating to
the latest release is impossible, the individual changes to resolve this
issue can be found at these commits:
https://git.kernel.org/stable/c/
c83d464b82a8ad62ec9077637f75d73fe955635a
https://git.kernel.org/stable/c/
25eaef533bf3ccc6fee5067aac16f41f280e343e
https://git.kernel.org/stable/c/
adc539784c98a7cc602cbf557debfc2e7b9be8b3
Signed-off-by: Antonio Flores <antflores627@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16420
Signed-off-by: Robert Marko <robimarko@gmail.com>
Mieczyslaw Nalewaj [Sat, 21 Sep 2024 07:19:11 +0000 (09:19 +0200)]
packages: remove remnants of kernels below 6.6
Remove remnants of kernels below 6.6.
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Link: https://github.com/openwrt/openwrt/pull/16432
Signed-off-by: Robert Marko <robimarko@gmail.com>
Hauke Mehrtens [Sat, 21 Sep 2024 09:24:40 +0000 (11:24 +0200)]
ath79: Refresh kernel patches
Make the patches apply cleanly again.
Fixes: 3660ddb8ab6e ("generic: ar8216: remove support for Linux before version 6.1")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Daniel Golle [Tue, 20 Aug 2024 22:14:30 +0000 (23:14 +0100)]
mediatek: add Adtran SmartRG SDG-8733A
Specification is similar to other devices of the MT Stuart series:
* Mediatek MT7988D (3x Cortex-A73, up to 1.8 GHz clock speed)
* 8 GiB eMMC
* 2 GiB DDR4 RAM
* 2500M/1000M/100M LAN port
* 10000M/5000M/2500M/1000M/100M/10M WAN port
* MT7992 Tri-band (2.4G, 5G, 6G) 2T2R+3T3R+3T3R 802.11be Wi-Fi
* Renesas DA14531MOD Bluetooth
* 2 buttons (Reset, Mesh/WPS)
* uC-controlled RGB LED via I2C
* 2x LED for the 2.5G port, 3x LED for the 10G port
* 3.3V-level 115200 baud UART console via 4-pin Dupont connector
exposed at the bottom of the device
* USB-C PD power input
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Daniel Golle [Wed, 21 Aug 2024 22:46:10 +0000 (23:46 +0100)]
generic: phy: aquantia: add pending patch to force MDI pair order
Import pending patch to force MDI pair order.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Felix Fietkau [Fri, 20 Sep 2024 21:17:28 +0000 (23:17 +0200)]
bpf-headers: update to version 6.6
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Felix Fietkau [Fri, 20 Sep 2024 21:15:24 +0000 (23:15 +0200)]
qosify: update to Git HEAD (2024-09-20)
850cc271083d qosify: add support for keeping stats
1501e0935175 bpf_skb_utils.h: add missing include to fix build against newer kernel headers
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Daniel Golle [Fri, 20 Sep 2024 18:26:52 +0000 (19:26 +0100)]
generic: remove support for older kernels from swconfig
The legacy swconfig switch driver framework supports kernels older than
Linux 6.6 by using #ifdef'ery with LINUX_VERSION_CODE. Remove all that.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Daniel Golle [Fri, 20 Sep 2024 18:24:17 +0000 (19:24 +0100)]
generic: ar8216: remove support for Linux before version 6.1
Drop support for older kernel versions from legacy AR8216 switch driver.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Daniel Golle [Fri, 20 Sep 2024 17:55:32 +0000 (18:55 +0100)]
generic: drop 6.1 support
Drop config and files for Linux 6.1.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Daniel Golle [Fri, 20 Sep 2024 17:53:46 +0000 (18:53 +0100)]
kirkwood: remove left-over files-6.1 folder
Remove folder with DTS files for Linux 6.1 which has already been
dropped.
Fixes: f142ce87d9 ("kirkwood: remove 6.1 support")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Daniel Golle [Fri, 20 Sep 2024 17:48:01 +0000 (18:48 +0100)]
armsr: remove left-over patches for kernel 6.1
Support for Linux 6.1 has already been removed from the armsr target.
Remove left-over patches-6.1 folder as well.
Fixes: fd47fdf527 ("armsr: Remove kernel 6.1 configuration")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Daniel Golle [Fri, 20 Sep 2024 17:46:18 +0000 (18:46 +0100)]
layerscape: remove left-over config-6.1 files
Remove left-over config-6.1 files which should have been removed
when removing kernel 6.1 support.
Fixes: f20987c161 ("layerscape: remove kernel 6.1 support")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Daniel Golle [Fri, 20 Sep 2024 17:45:07 +0000 (18:45 +0100)]
pistachio: drop files for Linux 6.1
Drop obsolete config and patches for Linux 6.1.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
David Bauer [Sat, 14 Sep 2024 17:10:10 +0000 (19:10 +0200)]
ipq40xx: add PoE passthrough GPIO
Add the GPIO pin of the PoE passthrough switch on the Aruba AP-303H.
Power is activated when the pin is low. It enables a PSE chip, so power
is only supplied to downstream devices when they are 802.3af/at
compliant devices.
Ensure you use a sufficient power supply when chaining a consuming
device after the AP.
Signed-off-by: David Bauer <mail@david-bauer.net>
Mieczyslaw Nalewaj [Sun, 8 Sep 2024 08:11:15 +0000 (10:11 +0200)]
qoriq: drop 6.1 support
Drop config for Linux 6.1.
Link: https://github.com/openwrt/openwrt/pull/16120
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Mieczyslaw Nalewaj [Fri, 9 Aug 2024 15:47:02 +0000 (17:47 +0200)]
qoriq: use kernel 6.6 by default
Switch to Linux kernel version 6.6.
Link: https://github.com/openwrt/openwrt/pull/16120
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Mieczyslaw Nalewaj [Fri, 9 Aug 2024 16:00:21 +0000 (18:00 +0200)]
at91: drop 6.1 support
Drop config and files for Linux 6.1.
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Mieczyslaw Nalewaj [Fri, 9 Aug 2024 15:57:23 +0000 (17:57 +0200)]
at91: use kernel 6.6 by default
Switch to Linux kernel version 6.6.
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Felix Fietkau [Fri, 20 Sep 2024 14:55:45 +0000 (16:55 +0200)]
tools/llvm-bpf: filter out STAGING_DIR_HOST/include from cflags on non-linux systems
Avoids picking up an incompatible libuuid from util-linux
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Daniel Golle [Thu, 19 Sep 2024 13:33:15 +0000 (14:33 +0100)]
generic: 6.6: mtk_eth_soc: increase QDMA RESV_BUF size
Increase QDMA RESV_BUF from 2K to 3K for netsys v2 to match Mediatek SDK.
This helps reduce the possibility of Ethernet transmit timeouts.
Link: https://git01.mediatek.com/plugins/gitiles/openwrt/feeds/mtk-openwrt-feeds/+/19d8456c3051e5f6dabf42fa770916a2126ea4bf
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Daniel Golle [Wed, 18 Sep 2024 01:12:24 +0000 (02:12 +0100)]
generic: 6.6: mtk_eth_soc: reset all TX queues on DMA free
The purpose of resetting the TX queue is to reset the
byte and packet count as well as to clear the software
flow control XOFF bit.
MediaTek developers pointed out that netdev_reset_queue would only
resets queue 0 of the network device.
Queues that are not reset may cause unexpected issues.
Packets may stop being sent after reset and "transmit timeout" log may
be displayed.
Import fix from MediaTek's SDK to resolve this issue.
Link: https://git01.mediatek.com/plugins/gitiles/openwrt/feeds/mtk-openwrt-feeds/+/5746a94456f466446cc0dcdfbd9078df6df31b63
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Felix Fietkau [Fri, 20 Sep 2024 09:23:24 +0000 (11:23 +0200)]
ucode: another fix for host installation
The previous host installation fix accidentally moved the rpath settings
out of CMAKE_HOST_OPTIONS and into CMAKE_OPTIONS.
Fixes: ae42ecaad4e7 ("ucode: fix host installation")
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Mieczyslaw Nalewaj [Wed, 18 Sep 2024 08:48:03 +0000 (10:48 +0200)]
packages: remove kernel 5.15 remnants
Remove kernel 5.15 remnants.
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Link: https://github.com/openwrt/openwrt/pull/16417
Signed-off-by: Robert Marko <robimarko@gmail.com>
Mieczyslaw Nalewaj [Tue, 17 Sep 2024 20:02:06 +0000 (22:02 +0200)]
generic: drop 5.15 support
Drop config and files for Linux 5.15.
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Link: https://github.com/openwrt/openwrt/pull/16417
Signed-off-by: Robert Marko <robimarko@gmail.com>
Mieczyslaw Nalewaj [Tue, 17 Sep 2024 19:59:28 +0000 (21:59 +0200)]
realtek: drop 5.15 support
Drop config and files for Linux 5.15.
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Link: https://github.com/openwrt/openwrt/pull/16417
Signed-off-by: Robert Marko <robimarko@gmail.com>
Mikhail Zhilkin [Sat, 31 Aug 2024 14:21:06 +0000 (14:21 +0000)]
ramips: add support for netis N6
This commit adds support for netis N6 WiFi 6 router.
Specification
-------------
- SoC : MediaTek MT7621AT, MIPS, 880 MHz
- RAM : 256 MiB
- Flash : NAND 128 MiB (ESMT PSU1GA30DT)
- WLAN : MT7905DAN + MT7975DN
- 2.4 GHz : b/g/n/ax, 574 Mbps, MIMO 2x2
- 5 GHz : a/n/ac/ax, 1201 Mbps, MIMO 2x2
- Ethernet : 10/100/1000 Mbps x5 (1x WAN, 4x LAN)
- USB : 1x 3.0
- UART : 3.3V, 115200n8
- Buttons : 1x Reset
1x WPS
- LEDs : 1x Power (green)
1x System (green)
1x WAN (green)
1x WiFi 2.4 GHz (green), controlled by phy
1x WiFi 5 GHz (green), controlled by phy
1x WPS (green)
1x USB (green)
5x ethernet leds (green), controlled by switch
- Power : 12 VDC, 1.5 A
Installation
------------
1. Update the router using stock firmware web interface and OpenWrt
factory.bin image.
Recovery and return to stock
----------------------------
1. Assign your PC a static IP 192.168.1.2 and connect to the router using
the ethernet cable;
2. Power off the router;
3. Press Reset button, power on the router and wait until ethernet led
start blinking;
4. Release the button;
5. Open http://192.168.1.1/ (N6 System Recovery Mode) in your browser;
6. Upload OpenWrt factory.bin (or stock firmware *.bin) image and proceed
with upgrade.
MAC addresses
-------------
+---------+-------------------+
| | MAC example |
+---------+-------------------+
| LAN | dc:xx:xx:49:xx:04 |
| WAN | dc:xx:xx:49:xx:05 |
| WLAN 2g | dc:xx:xx:19:xx:06 |
| WLAN 5g | dc:xx:xx:79:xx:06 |
+---------+-------------------+
The WLAN MAC prototype was found in 'Factory', 0x4
The LAN MAC was found in 'Factory', 0x7ef20
The WAN MAC was found in 'Factory', 0x7ef26
Known issue
-----------
2.4 GHz WLAN doesn't start with mt76 driver.
Probable reason:
Original Netis N6 EEPROM contains wrong MT_EE_WIFI_CONF value (0xd2).
Other routers with the same WLAN hardware (e.g., Routerich AX1800)
have MT_EE_WIFI_CONF = 0x92.
Workaround (already included in this commit):
Extract EEPROM to a file at the first time boot and change
MT_EE_WIFI_CONF (offset 0x190) value from 0xd2 to 0x92. See
/etc/hotplug.d/firmware/11-mt76-caldata for details.
Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16322
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Mikhail Zhilkin [Sat, 31 Aug 2024 14:05:39 +0000 (14:05 +0000)]
ramips: fix wrong dts files permissions
This files are executable:
target/linux/ramips/dts/mt7621_openfi_5pro.dts
target/linux/ramips/dts/mt7621_winstars_ws-wn536p3.dts
Has to be fixed.
Fixes: 5560791 ("ramips: add support for OpenFi 5Pro Travel Router")
Fixes: 2da2705 ("ramips: add support for WINSTARS WS-WN536P3")
Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16322
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Yanase Yuki [Fri, 13 Sep 2024 10:22:28 +0000 (19:22 +0900)]
tools/expat: update to 2.6.3
This release fixes CVE-2024-45490, CVE-2024-45491 and
CVE-2024-45492.
Changelog:
https://github.com/libexpat/libexpat/blob/R_2_6_3/expat/Changes
Signed-off-by: Yanase Yuki <dev@zpc.st>
Link: https://github.com/openwrt/openwrt/pull/16379
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
John Audia [Wed, 18 Sep 2024 19:29:06 +0000 (15:29 -0400)]
kernel: bump 6.6 to 6.6.52
Changelog: https://cdn.kernel.org/pub/linux/kernel/v6.x/ChangeLog-6.6.52
Removed upstreamed:
backport-6.6/819-v6.8-0010-nvmem-core-add-nvmem_dev_size-helper.patch[1]
backport-6.6/819-v6.8-0011-nvmem-u-boot-env-use-nvmem_add_one_cell-nvmemsubsys.patch[2]
backport-6.6/819-v6.8-0012-nvmem-u-boot-env-use-nvmem-device-helpers.patch[3]
backport-6.6/819-v6.8-0013-nvmem-u-boot-env-improve-coding-style.patch[4]
backport-6.6/822-v6.11-0011-nvmem-u-boot-env-error-if-NVMEM-device-is-too-small.patch[5]
Manually rebased:
starfive/patches-6.6/0048-riscv-dts-starfive-Add-full-support-except-VIN-and-V.patch
All other patches automatically rebased.
1. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v6.6.52&id=
820b1b981aeb8b8e60db2835ddd430c9d1bc6072
2. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v6.6.52&id=
ae91c9c7b67d4d47206fe8cbb2ab89687d283dcc
3. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v6.6.52&id=
2eea394c31cbc3d853a26ef2ddb8f5bd24d4d002
4. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v6.6.52&id=
368fa77b7945bdbdf0e3bb26b5abcae4fba25a20
5. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v6.6.52&id=
2278629c3ebb1a912fe0a1f19f088312600742a4
Build system: x86/64
Build-tested: x86/64/AMD Cezanne, flogic/xiaomi_redmi-router-ax6000-ubootmod, ramips/tplink_archer-a6-v3
Run-tested: x86/64/AMD Cezanne, flogic/xiaomi_redmi-router-ax6000-ubootmod, ramips/tplink_archer-a6-v3
Signed-off-by: John Audia <therealgraysky@proton.me>
Link: https://github.com/openwrt/openwrt/pull/16422
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Daniel Golle [Thu, 19 Sep 2024 19:12:54 +0000 (20:12 +0100)]
mediatek: filogic: openwrt_one: let U-Boot set LAN MAC address
Instead of reading it from flash directly, let U-Boot assign the LAN
MAC address. Set label-mac-device while at it and sort aliases in DT
alphabetically.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Daniel Golle [Thu, 19 Sep 2024 18:26:57 +0000 (19:26 +0100)]
uboot-mediatek: openwrt_one: set ethaddr from factory
Set LAN MAC address from factory partition on NOR flash.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Daniel Golle [Thu, 19 Sep 2024 17:39:56 +0000 (18:39 +0100)]
at91: 6.6: add missing kernel symbols
Kconfig symbols CONFIG_VIDEO_MICROCHIP_CSI2DC, CONFIG_VIDEO_MICROCHIP_ISC
and CONFIG_VIDEO_MICROCHIP_XISC are missing for sama5 and sama7 causing
the build to abort or waiting for user input. Add the symbols (disabled)
so build with Linux 6.6 succeeds.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Daniel Golle [Thu, 19 Sep 2024 13:36:43 +0000 (14:36 +0100)]
mediatek: filogic: fix WiFi MAC address retrieval for Adtran SDG-8734
Fix a typo in the MAC address assignment script affecting SDG-8734.
Fixes: c71b68acdd ("mediatek: filogic: add Adtran SmartRG Mount Stuart series")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Andreas Gnau [Mon, 16 Sep 2024 22:07:46 +0000 (00:07 +0200)]
dtc: Update to 1.7.1
Update to dtc to 1.7.1. Change tarball to gzip and drop upstreamed patch
010-both-libraries.patch. Disable tests.
Changes sinve v1.7.0 include:
* dtc
* Fix check for 10-bit I2C addresses
* Improve documentation of -@ option
* Update to libyaml >= 0.2.3
* Improvements & fixes for device graph checks
* Add -L / --local-fixups option
* Add check for length of interrupt-map properties
* libfdt
* Add fdt_path_getprop_namelen()
* Add fdt_get_symbol() and fdt_get_symbol_namelen()
* Correct documentation of fdt_path_offset()
* Correct documentation of fdt_appendprop_addrrange()
* Validate aliases is fdt_get_alias_namelen()
* Don't overwrite phandles when applying overlays
* Require Python 3
* pylibfdt
* Support boolean properties
* Fixes for current Python versions
* General
* Assorted bugfixes
* Assorted build improvements
* Assorted typo fixes in docs
* Some additional testcases
* Move to GitHub Actions based CI
Signed-off-by: Andreas Gnau <andreas.gnau@iopsys.eu>
Link: https://github.com/openwrt/openwrt/pull/16411
Signed-off-by: Robert Marko <robimarko@gmail.com>
Christian Marangi [Wed, 18 Sep 2024 23:01:27 +0000 (01:01 +0200)]
kernel: rework Initramfs compile cpio handling
Now that we copy and then delete the Per-Device rootfs linux directory,
it's not valid anymore placing the generated cpio there as artifacts
or subsequent commands need the generated cpio.
To handle this, rework Initramfs compile cpio handling by placing them in
the KERNEL_BUILD_DIR but add to the name the rootfs HASH ID.
To also prevent race condition, generate and access these file under a
lock to prevent fit command to reference a cpio while a parallel
execution is genereting it.
Fixes: 52cc9d82f113 ("kernel: rework Initramfs locking logic")
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Christian Marangi [Wed, 18 Sep 2024 22:58:44 +0000 (00:58 +0200)]
kernel: fix flock name for gen-initramfs lock
Fix flock name for gen-initramfs lock as $(2) starts with .HASH making
the lock name gen-initramfs-.HASH.flock
Fix this to a better name of gen-initramfs.HASH.flock
Fixes: 52cc9d82f113 ("kernel: rework Initramfs locking logic")
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Christian Marangi [Wed, 18 Sep 2024 22:56:32 +0000 (00:56 +0200)]
kernel: fix wrong rework for Initramfs cpio xz compression
Fix wrong rework for Initramfs cpio xz compression where it was wrongly
dropped the Per-Device linux directory if condition.
Fixes: 52cc9d82f113 ("kernel: rework Initramfs locking logic")
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Yanase Yuki [Fri, 13 Sep 2024 10:16:29 +0000 (19:16 +0900)]
tools/cmake: update to 3.30.3
Release notes: https://cmake.org/cmake/help/latest/release/3.30.html
Signed-off-by: Yanase Yuki <dev@zpc.st>
Link: https://github.com/openwrt/openwrt/pull/16378
Signed-off-by: Robert Marko <robimarko@gmail.com>
Stephen Howell [Tue, 25 Apr 2023 15:32:07 +0000 (17:32 +0200)]
realtek: add support for HPE 1920-48G (JG927A) and 1920-48G-PoE (JG928A)
Hardware information:
---------------------
- SoC: RTL8393M
- Copper phy: 6×RTL8218B
- Fibre phy: RTL8214FC
- Flash: 32MiB SPI NOR, MX25L25635FMI
- RAM: 128MiB DDR3, Micron MT41K64M16TW-107
- Serial port: ±5V serial port to RJ45, ZT3232 (MAX3232 compatible)
- +370W POE on JG928A model
Note: SFP ports currently non-functional due to missing support for
RTL8214FC on the RTL8393M target.
Updated for Linux 6.6 kernel.
Installation:
-------------
- Initial installation follows same process as HPE 1920-24G (JG924A)
- Based on prior work of Jan Hoffmann <jan@3e8.eu>
- Additional work by Andreas Böhler <dev@aboehler.at>
- PoE updates and tidy-up by Stephen Howell <howels@allthatwemight.be>
Signed-off-by: Stephen Howell <howels@allthatwemight.be>
Robert Marko [Tue, 17 Sep 2024 10:54:47 +0000 (12:54 +0200)]
realtek: default to 6.6
Now that there is 6.6 support for realtek, lets encourage testing it by
making it default so 5.15 can be dropped ASAP.
Link: https://github.com/openwrt/openwrt/pull/16408
Signed-off-by: Robert Marko <robimarko@gmail.com>
Daniel Golle [Tue, 17 Sep 2024 16:29:20 +0000 (17:29 +0100)]
generic: 6.6: backport pending fix for Aquantia PHY LEDs
The 'active-low' property was not applied correctly and two fixes
are required to make inverted LEDs work as expected.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Daniel Golle [Tue, 17 Sep 2024 18:06:55 +0000 (19:06 +0100)]
rpcd: update to git HEAD
bcc091d session: Fix crash when the UCI option 'password' or 'username' is missing
9f4b86e rpcd: iwinfo: add IEEE 802.11be support
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Daniel Golle [Tue, 17 Sep 2024 18:03:29 +0000 (19:03 +0100)]
iwinfo: update to git HEAD
Add support for 802.11be (HE) radios.
4b7c47c iwinfo: sync with upstream nl80211.h
268a662 iwinfo: add basic IEEE 802.11be support
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Mieczyslaw Nalewaj [Fri, 2 Aug 2024 20:37:28 +0000 (22:37 +0200)]
at91: enable 6.6 testing kernel
The at91 now supports 6.6 kernel as testing.
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Link: https://github.com/openwrt/openwrt/pull/16058
Signed-off-by: Nick Hainke <vincent@systemli.org>
Mieczyslaw Nalewaj [Sat, 3 Aug 2024 00:48:13 +0000 (02:48 +0200)]
at91: refresh config-6.6
Refresh kernel config for Linux 6.6.
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Link: https://github.com/openwrt/openwrt/pull/16058
Signed-off-by: Nick Hainke <vincent@systemli.org>
Mieczyslaw Nalewaj [Sat, 3 Aug 2024 13:58:04 +0000 (15:58 +0200)]
at91: 6.6: change dts files location
Change dts files location to subfolder microchip for compatibility with kernel 6.6
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Link: https://github.com/openwrt/openwrt/pull/16058
Signed-off-by: Nick Hainke <vincent@systemli.org>
Mieczyslaw Nalewaj [Fri, 2 Aug 2024 20:26:02 +0000 (22:26 +0200)]
at91: 6.6: remove obsolete patches
Remove obsolete patches no longer applicable to the 6.6 kernel.
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Link: https://github.com/openwrt/openwrt/pull/16058
Signed-off-by: Nick Hainke <vincent@systemli.org>
Mieczyslaw Nalewaj [Sat, 3 Aug 2024 13:53:45 +0000 (15:53 +0200)]
kernel/at91: Restore kernel files for v6.1
This is an automatically generated commit which aids following Kernel patch
history, as git will see the move and copy as a rename thus defeating the
purpose.
For the original discussion see:
https://lists.openwrt.org/pipermail/openwrt-devel/2023-October/041673.html
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Link: https://github.com/openwrt/openwrt/pull/16058
Signed-off-by: Nick Hainke <vincent@systemli.org>
Mieczyslaw Nalewaj [Sat, 3 Aug 2024 13:53:44 +0000 (15:53 +0200)]
kernel/at91: Create kernel files for v6.6 (from v6.1)
This is an automatically generated commit.
When doing `git bisect`, consider `git bisect --skip`.
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Link: https://github.com/openwrt/openwrt/pull/16058
Signed-off-by: Nick Hainke <vincent@systemli.org>
Mieczyslaw Nalewaj [Sat, 3 Aug 2024 13:53:04 +0000 (15:53 +0200)]
at91: remove unnecessary dts files
Remove unnecessary dts files already included in the 6.1 kernel.
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Link: https://github.com/openwrt/openwrt/pull/16058
Signed-off-by: Nick Hainke <vincent@systemli.org>
Chuanhong Guo [Thu, 8 Aug 2024 04:56:03 +0000 (12:56 +0800)]
siflower: new target for Siflower SF19A2890
Siflower SF19A2890 is an SoC with:
Dual-core MIPS InterAptiv at 800MHz
DDR3 controller
One Gigabit Ethernet MAC with RGMII and IPv4 HNAT engine
Built-in 2x2 11N + 2x2 11AC WiFi radio
USB 2.0 OTG
I2C/SPI/GPIO and various other peripherals
This PR adds support for SF19A2890 EVB with ethernet support.
EVB spec:
Memory: DDR3 128M
Ethernet: RTL8367RB 5-port gigabit switch
Flash: 16M NOR
Others: MicroUSB OTG, LED x 1, Reset button x1
The built image can be flashed using u-boot recovery.
This target is marked as source-only until support for a commercial
router board comes.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
Chuanhong Guo [Thu, 15 Aug 2024 08:04:30 +0000 (16:04 +0800)]
package: busybox: disable mips16 on hard-float
The busybox built with mips16 enabled has broken seq command.
Disassembling shows that the call to hard-float strtod in mips16
code is generated without the __call_stub_fp:
```
0x00406d6f <+118>: lw v0,32(sp)
0x00406d71 <+120>: sll s0,2
0x00406d73 <+122>: addu s0,v0,s0
0x00406d75 <+124>: lw a0,-4(s0)
0x00406d79 <+128>: jal 0x44ebc1 <strtod@mips16plt>
0x00406d7d <+132>: addiu a1,sp,84
0x00406d7f <+134>: sw v0,64(sp)
0x00406d81 <+136>: lw v0,0(s1)
0x00406d83 <+138>: sw v1,68(sp)
```
As a result, strtod returns the result in float point registers
while the calling mips16 code expect the result in v0/v1.
Disable mips16 on hard-float targets for now. The built .ipk goes
from 213316 bytes to 251419 bytes.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
Andreas Böhler [Sun, 15 Sep 2024 21:35:08 +0000 (23:35 +0200)]
ramips: mt7621: use lzma-loader for Sercomm NA502s
This fixes a well-known "LZMA ERROR 1" error on Sercomm NA502s, reported
on the OpneWrt forum [0].
[0] https://forum.openwrt.org/t/206640
Signed-off-by: Andreas Böhler <dev@aboehler.at>
Rosen Penev [Thu, 15 Aug 2024 02:25:21 +0000 (19:25 -0700)]
ramips: mtd_eth_soc: use dev_err_probe
Simplifies the code by avoiding having to manually handle -EPROBE_DEFER.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Chuanhong Guo [Tue, 17 Sep 2024 13:41:10 +0000 (21:41 +0800)]
toolchain: gcc: drop 110-Fix-MIPS-PR-84790.patch
According to the bugzilla link, this is fixed in gcc 14.2.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
Christian Marangi [Mon, 16 Sep 2024 16:38:16 +0000 (18:38 +0200)]
kernel: copy kernel build dir on Per-Device Initramfs compilation
To speedup compilation of Per-Device Initramfs, copy the kernel build
directory for each rootfs ID.
This permits concurrent execution of kernel build without conflicting
with each other at the expense of additional disk space usage.
To limit disk space usage, the copied kernel directory is deleted after
the Per-Device Initramfs image is generated and saved.
Link: https://github.com/openwrt/openwrt/pull/16404
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Christian Marangi [Mon, 16 Sep 2024 16:34:09 +0000 (18:34 +0200)]
kernel: rework Initramfs locking logic
Rework CompileImage/Initramfs locking logic to fix race condition on
concurrent access/compilation.
Rework each intermediate step and group them under one single execution
block. Protect this with a new lock, 'gen-initramfs' and rename the
compile initramfs to compile-initramfs lock name.
This is done to handle corner case scenario where a rootfs with the same
hash ID is generated at the same time. To handle this, we execute
everything under lock and use a specific hash ID lock to prevent
concurrent access/compilation.
Link: https://github.com/openwrt/openwrt/pull/16404
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Olcay Korkmaz [Mon, 16 Sep 2024 21:28:21 +0000 (00:28 +0300)]
toolchain: binutils: add support for 2.43.1
Release notes:
https://lists.gnu.org/archive/html/info-gnu/2024-08/msg00003.html
No need to refresh patches
Test device: Xiaomi ax3600
Signed-off-by: Olcay Korkmaz <nuke_mania@hotmail.com>
Link: https://github.com/openwrt/openwrt/pull/16405
Signed-off-by: Robert Marko <robimarko@gmail.com>
Robert Marko [Mon, 16 Sep 2024 09:51:45 +0000 (11:51 +0200)]
generic: enable RELR relocations
RELR is a relocation packing format for relative relocations.
Linux has supported using it for ARM64 since 5.4, and more recently
for LoongArch as well.
It requires compatible tooling as well, so only with binutils 2.43
TOOLS_SUPPORT_RELR is set and thus RELR available.
RELR should always decrease the binary size and while testing this
the default build for Dynalink WRX-36 (qualcommax/ipq807x) reduced
the compressed kernel size by 38k and uncompressed one by 640k.
So, lets enable it in the default config.
Link: https://github.com/openwrt/openwrt/pull/16403
Signed-off-by: Robert Marko <robimarko@gmail.com>
Markus Stockhausen [Sat, 14 Sep 2024 20:39:12 +0000 (16:39 -0400)]
realtek: 6.6: MDIO post fixes
Merging of the realtek 6.6 series forgot to include some final fixes
for the new MDIO driver. What was changed in last second?
1. The MDIO driver used wrong constants to make use of the raw
page (for direct register access). Provide a rawpage variable in
the bus private structure, populate it during initialization and
make use of it at the proper places
2. We always used the variable portaddr for the bus index. Usually
our driver uses either addr or port for the same meaning. Remove the
duplication and reuse the normal addr variable.
3. Drop functions rtmdio_write_page() and rtmdio_read_page(). These
only call the PHY driver read/write page functions. We know that
these will only access page 0x1f. As we have only Realtek PHYs
and our driver only reacts to this special page, just hardcode it.
Benefit is that we can use these functions for PHY detection when
read/write page functions are not yet assigned.
4. Add two new helper functions phy_port_read_paged() and
phy_port_write_paged(). These allow to access arbitrary ports on
the MDIO bus when the packages are not initialized. These will be
needed for proper RTL8218B and RTL8214FC detection in forthcoming
patches.
5. The port tracking wrongly used index 0 to mark "normal" access.
This does not allow to make a "special" access to port 0. Use
index -1 to mark "normal" access.
Provide the fix for 5.15 and 6.6 to allow for easy version
comparison.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/16391
Signed-off-by: Robert Marko <robimarko@gmail.com>
Markus Stockhausen [Sat, 14 Sep 2024 20:26:34 +0000 (16:26 -0400)]
realtek: 5.15: backport VLAN fix
With commit
a22d359fa56fe0 VLAN handling was fixed for kernel 6.6.
This restored network connectivity of the devices. For easy testing
backport the fix for 5.15 too.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/16391
Signed-off-by: Robert Marko <robimarko@gmail.com>
Markus Stockhausen [Sat, 14 Sep 2024 20:22:40 +0000 (16:22 -0400)]
realtek: 6.6: Support XGMII attached PHYs
On the XGS1210-12 the RTL8218D is attached via XGMII. Add this to the
supported list in the DSA driver.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/16391
Signed-off-by: Robert Marko <robimarko@gmail.com>
Ivan Pavlov [Sat, 7 Sep 2024 17:54:34 +0000 (20:54 +0300)]
hostapd: update to version 2024-09-15
Remove upstreamed from 2.11 release:
060-nl80211-fix-crash-when-adding-an-interface-fails.patch
Rebase all other patches
Signed-off-by: Ivan Pavlov <AuthorReflex@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16338
Signed-off-by: Robert Marko <robimarko@gmail.com>
Ivan Pavlov [Thu, 15 Aug 2024 18:47:25 +0000 (21:47 +0300)]
hostapd: update to 2.11 release tag
Release 2.11 has been quite a few new features and fixes since the 2.10
release. The following ChangeLog entries highlight some of the main
changes:
* Wi-Fi Easy Connect
- add support for DPP release 3
- allow Configurator parameters to be provided during config exchange
* HE/IEEE 802.11ax/Wi-Fi 6
- various fixes
* EHT/IEEE 802.11be/Wi-Fi 7
- add preliminary support
* SAE: add support for fetching the password from a RADIUS server
* support OpenSSL 3.0 API changes
* support background radar detection and CAC with some additional
drivers
* support RADIUS ACL/PSK check during 4-way handshake (wpa_psk_radius=3)
* EAP-SIM/AKA: support IMSI privacy
* improve 4-way handshake operations
- use Secure=1 in message 3 during PTK rekeying
...and many more
Remove upstreamed patches:
023-ndisc_snoop-call-dl_list_del-before-freeing-ipv6-add.patch
030-driver_nl80211-rewrite-neigh-code-to-not-depend-on-l.patch
040-mesh-allow-processing-authentication-frames-in-block.patch
181-driver_nl80211-update-drv-ifindex-on-removing-the-fi.patch
182-nl80211-move-nl80211_put_freq_params-call-outside-of.patch
183-hostapd-cancel-channel_list_update_timeout-in-hostap.patch
210-build-de-duplicate-_DIRS-before-calling-mkdir.patch
253-qos_map_set_without_interworking.patch
751-qos_map_ignore_when_unsupported.patch
800-SAE-Check-for-invalid-Rejected-Groups-element-length.patch
801-SAE-Check-for-invalid-Rejected-Groups-element-length.patch
802-SAE-Reject-invalid-Rejected-Groups-element-in-the-pa.patch
Other patches has been updated.
Signed-off-by: Ivan Pavlov <AuthorReflex@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16338
Signed-off-by: Robert Marko <robimarko@gmail.com>
Mauri Sandberg [Mon, 31 Jul 2023 12:35:46 +0000 (15:35 +0300)]
ramips: mt7621: Add DNA Valokuitu Plus EX400
Specifications:
- Device: DNA Valokuitu Plus EX400
- SoC: MT7621A
- Flash: 256MB NAND
- RAM: 256MB
- Ethernet: Built-in, 2 x 1GbE
- Wifi: MT7603 2.4 GHz, MT7615 5 GHz (4x internal antennas)
- USB: 1x 3.0
- LED: 1x green/red, 1x green
- Buttons: Reset
MAC addresses:
- LAN: u-boot 'ethaddr' (label)
- WAN: label + 1
- 2.4 GHz: label + 6
- 5 GHz: label + 7
Serial:
There is a black block connector next to the red ethernet connector. It
is accessible also through holes in the casing.
Pinout (TTL 3.3V)
+---+---+
|Tx |Rx |
+---+---+
|Vcc|Gnd|
+---+---+
Firmware:
The vendor firmware is a fork of OpenWrt (Reboot) with a kernel version
4.4.93. The flash is arranged as below and there is a dual boot
mechanism alternating between rootfs_0 and rootfs_1.
+-------+------+------+-----------+-----------+
| | env1 | env2 | rootfs_0 | rootfs_1 |
| +------+------+-----------+-----------+
| | UBI volumes |
+-------+-------------------------------------+
|U-Boot | UBI |
+-------+-------------------------------------+
|mtd0 | mtd1 |
+-------+-------------------------------------+
| NAND |
+---------------------------------------------+
In OpenWrt rootfs_0 will be used as a boot partition that will contain the
kernel and the dtb. The squashfs rootfs and overlay are standard OpenWrt
behaviour.
+-------+------+------+-----------+--------+------------+
| | env1 | env2 | rootfs_0 | rootfs | rootfs_data|
| +------+------+-----------+--------+------------+
| | UBI volumes |
+-------+-----------------------------------------------+
|U-Boot | UBI |
+-------+-----------------------------------------------+
|mtd0 | mtd1 |
+-------+-----------------------------------------------+
| NAND |
+-------------------------------------------------------+
U-boot:
With proper serial access booting can be halted to U-boot by pressing any
key. TFTP and flash writes are available, but only the first one has been
tested.
NOTE: Recovery mode can be accessed by holding down the reset button while
powering on the device. The led 'Update' will show a solid green light
once ready. A web server will be running at 192.168.1.1:80 and it will
allow flashing a firmware package. You can cycle between rootfs_0 and
rootfs_1 by pressing the reset button once.
Root password:
With the vendor web UI create a backup of your settings and download the
archive to your computer. Within the archive in the file
/etc/shadow replace the password hash for root with that of a password you
know. Restore the configuration with the vendor web UI and you will have
changed the root password.
SSH access:
You might need to enable the SSH service for LAN interface as by default
it's enabled for WAN only.
Installing OpenWrt:
With the vendor web UI install the OpenWrt factory image. Alternatively,
ssh to the device and use sysupgrade -n from cli.
Finalize by installing the OpenWrt sysupgrade image to get a fully
functioning system.
Reverting to the vendor firmware:
Boot with OpenWrt initramfs image
- Remove volumes rootfs_0, rootfs and rootfs_data and create vendor
volumes.
ubirmvol /dev/ubi0 -n 2
ubirmvol /dev/ubi0 -n 3
ubirmvol /dev/ubi0 -n 4
ubimkvol /dev/ubi0 -N rootfs_0 -S 990
ubimkvol /dev/ubi0 -N rootfs_1 -S 990
Power off and enter to the U-boot recovery to install the vendor
firmware.
Known issues:
- MACs for wifi are stored in currently unknown place but it seems
to persist over power-off. They might be stored on the chip.
Signed-off-by: Mauri Sandberg <maukka@ext.kapsi.fi>
[rmilecki: try NVMEM for MACs]
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Andre Heider [Sun, 4 Aug 2024 14:11:16 +0000 (16:11 +0200)]
omap: remove 6.1 support
We switched to 6.6, so lets remove 6.1 support now.
Signed-off-by: Andre Heider <a.heider@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16099
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Andre Heider [Sun, 4 Aug 2024 14:10:49 +0000 (16:10 +0200)]
omap: switch to kernel 6.6
Switch to Linux 6.6.
Signed-off-by: Andre Heider <a.heider@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16099
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
projects / openwrt / staging / blocktrron.git / log