drm/i915/tgl: Add DPLL registers

On TGL the port programming for combophy is very similar to ICL, so
adapt the callers to possibly use the different register values.

v2 (Lucas): Add TODO with about DPLL4 (requested by Ville)

Cc: Vandita Kulkarni <vandita.kulkarni@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190711173115.28296-21-lucas.demarchi@intel.com

drm/i915/tgl: Add vbt value mapping for DDC Bus pin

Add VBT-value to DDC bus pin mapping for the same.

Signed-off-by: Mahesh Kumar <mahesh1.kumar@intel.com>
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190711173115.28296-20-lucas.demarchi@intel.com

drm/i915/tgl: port to ddc pin mapping

Make the icl function generic so it is based on phy type and can be
applied to tgl as well.

I checked if this could not apply to EHL as well, but unfortunately
there the HPD and DDC/GMBUS pins for DDI C are mapped to TypeC Port 1
even though it doesn't have TC phy.

v2: don't add a separate function for TGL, but rather reuse the ICL one
    (suggested by Rodrigo)
v3: rebase after the introduction of enum phy and use it for the
    conversions

Cc: Anusha Srivatsa <anusha.srivatsa@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190711173115.28296-19-lucas.demarchi@intel.com

drm/i915/tgl: Add gmbus gpio pin to port mapping

Add default GPIO pin mapping for all ports. Tiger Lake has 3 combophy
ports and 6 TC ports, gpio pin1-3 are mapped to combophy & pin9-14 are
mapped to TC ports.

Cc: Anusha Srivatsa <anusha.srivatsa@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Mahesh Kumar <mahesh1.kumar@intel.com>
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190711173115.28296-18-lucas.demarchi@intel.com

drm/i915/gen12: MBUS B credit change

Previously, the recommended B credit for all platforms was 24 / number
of pipes, which would give 6 for newer platforms with 4 pipes. However 6
is not enough and we need 12 on these cases.

We also need a different BW credit for these platforms.

Cc: Arthur J Runyan <arthur.j.runyan@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190711173115.28296-17-lucas.demarchi@intel.com

drm/i915/tgl: apply Display WA #1178 to fix type C dongles

Add port C to workaround to cover Tiger Lake.

Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190708231629.9296-22-lucas.demarchi@intel.com
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190711213517.13674-1-lucas.demarchi@intel.com

drm/i915/tgl: init ddi port A-C for Tiger Lake

This patch initializes DDI PORT A, B & C for Tiger lake. Other
TC ports need to be initialized later once corresponding code is there.

Cc: Madhav Chauhan <madhav.chauhan@intel.com>
Signed-off-by: Mahesh Kumar <mahesh1.kumar@intel.com>
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190711173115.28296-15-lucas.demarchi@intel.com

drm/i915/tgl: Add additional PHYs for Tiger Lake

Tiger Lake has up to 3 combo phys and 6 TC phys. Extend the helper
conversion functions from port to phy.

Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190711173115.28296-14-lucas.demarchi@intel.com

drm/i915/tgl: Add additional ports for Tiger Lake

There are 2 new additional typeC ports in Tiger Lake and PORT-C is now a
combophy port. This results in 6 typeC ports and 3 combophy ports.
These 6 TC ports can be DP alternate mode, DP over thunderbolt, native
DP on legacy DP connector or native HDMI on legacy connector.

v2: Rebase on new modular FIA code (Lucas)
v3: Also add new port in port_identifier(), even though it can't
    possibly be used there (requested by José)
v4: Add conversion port->tc_port in helper function after introction of
    phy namespace (Lucas)

Cc: Anusha Srivatsa <anusha.srivatsa@intel.com>
Signed-off-by: Vandita Kulkarni <vandita.kulkarni@intel.com>
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190711173115.28296-13-lucas.demarchi@intel.com

drm/i915/tgl: Add pll manager

Add a new pll array for Tiger Lake. The TC pll functions for type C will
be covered in later patches after its phy is implemented.

Cc: Madhav Chauhan <madhav.chauhan@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Vandita Kulkarni <vandita.kulkarni@intel.com>
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190711173115.28296-12-lucas.demarchi@intel.com

drm/i915/tgl: Add new pll ids

Add 2 new PLLs for additional TC ports. The names for the PLLs on TGL
changed, but most registers remained the same, like MGPLL5_ENABLE,
MGPLL6_ENABLE. So continue to use the name from ICL.

Cc: Madhav Chauhan <madhav.chauhan@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Vandita Kulkarni <vandita.kulkarni@intel.com>
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Reviewed-by: Anusha Srivatsa <anusha.srivatsa@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190711173115.28296-11-lucas.demarchi@intel.com

drm/i915/tgl: Add power well to support 4th pipe

Add power well 5 to support 4th pipe and transcoder on TGL.

Cc: James Ausmus <james.ausmus@intel.com>
Cc: Imre Deak <imre.deak@intel.com>
Signed-off-by: Mika Kahola <mika.kahola@intel.com>
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190711173115.28296-10-lucas.demarchi@intel.com

drm/i915/tgl: Add power well support

The patch adds the new power wells introduced by TGL (GEN 12) and
maps these to existing/new power domains. The changes for GEN 12 wrt
to GEN 11 are the following:

- Transcoder#EDP removed from power well#1 (Transcoder#A used in
  low-power mode instead)
- Transcoder#A is now backed by power well#1 instead of power well#3
- The DDI#B/C combo PHY ports are now backed by power well#1 instead of
  power well#3
- New power well#5 added for pipe#D functionality (TODO)
- 2 additional TC ports (TC#5-6) backed by power well#3, 2 port
  specific IO power wells (only for the non-TBT modes) and 4 port
  specific AUX power wells (2-2 for TBT vs. non-TBT modes)
- Power well#2 backs now VDSC/joining for pipe#A instead of VDSC for
  eDP and MIPI DSI (TODO)

On TGL Port DDI#C changed to be a combo PHY (native DP/HDMI) and
BSpec has renamed ports DDI#D-F to TC#4-6 respectively. Thus on ICL we
have the following naming for ports:

- Combo PHYs (native DP/HDMI):
  DDI#A-B
- TBT/non-TBT (TC altmode, native DP/HDMI) PHYs:
  DDI#C-F

Starting from GEN 12 we have the following naming for ports:
- Combo PHYs (native DP/HDMI):
  DDI#A-C
- TBT/non-TBT (TC altmode, native DP/HDMI) PHYs:
  DDI TC#1-6

To save some space in the power domain enum the power domain naming in
the driver reflects the above change, that is power domains TC#1-3 are
added as aliases for DDI#D-F and new power domains are reserved for
TC#4-6.

v2 (Lucas):
  - Separate out the bits and definitions for TGL from the ICL ones.
    Fix use of TRANSCODER_EDP_VDSC, that is now the correct define since
    we don't define TRANSCODER_A_VDSC power domain to spare a one bit in
    the bitmask (suggested by Ville)
v3 (Lucas):
  - Fix missing squashes on v2
  - Rebase on renamed TRANSCODER_EDP_VDSC

Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Anusha Srivatsa <anusha.srivatsa@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190711173115.28296-9-lucas.demarchi@intel.com

drm/i915/tgl: rename TRANSCODER_EDP_VDSC to use on transcoder A

On TGL the special EDP transcoder is gone and it should be handled by
transcoder A.

v2 (Lucas):
  - Reuse POWER_DOMAIN_TRANSCODER_EDP_VDSC (suggested by Ville)
  - Use crtc->dev since new_crtc_state->state may be NULL on atomic
    commit (suggested by Maarten)
v3 (Lucas):
  - Rename power domain so it's clear it can also be used for transcoder
    A in TGL (requested by José and Manasi)

Cc: Imre Deak <imre.deak@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Acked-by: José Roberto de Souza <jose.souza@intel.com>
Reviewed-by: Manasi Navare <manasi.d.navare@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190711173115.28296-8-lucas.demarchi@intel.com

drm/i915/tgl: Check if pipe D is fused

On Tiger Lake there is one more pipe - check if it's fused.

Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Reviewed-by: Mika Kahola <mika.kahola@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190711173115.28296-7-lucas.demarchi@intel.com

drm/i915/tgl: Add TGL PCI IDs

Current list of PCI IDs for Tiger Lake.

Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Mika Kahola <mika.kahola@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190711173115.28296-6-lucas.demarchi@intel.com

drm/i915/tgl: Add TGL PCH detection in virtualized environment

Assume PCH_TGP when platform is TGL.

Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Mahesh Kumar <mahesh1.kumar@intel.com>
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Reviewed-by: Anusha Srivatsa <anusha.srivatsa@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190711173115.28296-5-lucas.demarchi@intel.com

drm/i915/tgl: Introduce Tiger Lake PCH

Add the enum additions to TGP.

Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: David Weinehall <david.weinehall@intel.com>
Cc: James Ausmus <james.ausmus@intel.com>
Signed-off-by: Radhakrishna Sripada <radhakrishna.sripada@intel.com>
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190711173115.28296-4-lucas.demarchi@intel.com

drm/i915/tgl: add initial Tiger Lake definitions

Tiger Lake is a Intel® Processor containing Intel® HD Graphics.

This is just an initial Tiger Lake definition. PCI IDs, generic support
and new features coming in following patches.

v2 (Lucas):
  - Remove modular FIA - feature will be re-introduced in future

Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Reviewed-by: Anusha Srivatsa <anusha.srivatsa@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190711173115.28296-3-lucas.demarchi@intel.com

drm/i915: Add 4th pipe and transcoder

Add pipe D and transcoder D to prepare for platforms having them.

Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190711173115.28296-2-lucas.demarchi@intel.com

drm/i915: Don't overestimate 4:2:0 link symbol clock

With 4:2:0 output the LS clock can be half of what it is with 4:4:4.
Make that happen.

Cc: Gwan-gyeong Mun <gwan-gyeong.mun@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190710125851.3275-1-ville.syrjala@linux.intel.com
Reviewed-by: Gwan-gyeong Mun <gwan-gyeong.mun@intel.com>
Tested-by: Gwan-gyeong Mun <gwan-gyeong.mun@intel.com>

drm/i915: Copy name string into ring buffer for intel_update/disable_plane tracepoints

Currently the intel_update_plane and intel_disable_plane tracepoints record
the address of plane->name in the ring buffer, and then when reading the
ring buffer uses %s to get the name. The issue with this, is that those two
events can be minutes, hours or even days apart. It is very dangerous to
dereference a string pointer without knowing if it still exists or not.

The proper way to handle this is to use the __string() macro in the
tracepoint which will save the string into the ring buffer at the time of
recording. Then there's no worries if the original string still exists in
memory when the ring buffer is read.

Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
[vsyrjala: Rebase on top of drm-tip]
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190710171230.7471-1-ville.syrjala@linux.intel.com

drm/i915/guc: Drop redundant ctx param from kerneldoc

drivers/gpu/drm/i915/intel_guc_submission.c:799: warning: Excess function parameter 'ctx' description in 'guc_client_alloc'

Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Reviewed-by: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190711162415.2938-1-chris@chris-wilson.co.uk

drm/i915: Don't pass stack garbage to pcode in the second data register

Zero initialize val2 so that we don't pass stack garbage to
the pcode qgv read command. I suspect in this case pcode
just ignores the initial value in that registers, but better
safe than sorry.

Cc: Dan Carpenter <dan.carpenter@oracle.com>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190710134937.25835-1-ville.syrjala@linux.intel.com
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>

drm/i915: Use intel_ types in intel_atomic_commit()

Make life less annoying by favoring the intel_ types over
the drm_ types in intel_atomic_commit().

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190701160550.24205-6-ville.syrjala@linux.intel.com
Reviewed-by: Imre Deak <imre.deak@intel.com>

drm/i915: Use intel_ types in intel_{lock,modeset}_all_pipes()

Streamline the code a bit by using intel_ types instead of the
drm_ types.

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190701160550.24205-5-ville.syrjala@linux.intel.com
Reviewed-by: Imre Deak <imre.deak@intel.com>

drm/i915: Polish intel_atomic_track_fbs()

Streamline the code a bit by using intel_ types instead of drm_
types in intel_atomic_track_fbs().

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190701160550.24205-4-ville.syrjala@linux.intel.com
Reviewed-by: Imre Deak <imre.deak@intel.com>

drm/i915: Polish intel_shared_dpll_swap_state()

Use swap() instead of hand rolling it in intel_shared_dpll_swap_state(),
and pass in the intel_atomic_state instead of drm_atomic_state. Makes
the code less convoluted.

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190701160550.24205-3-ville.syrjala@linux.intel.com
Reviewed-by: Imre Deak <imre.deak@intel.com>

drm/i915: Simplify modeset_get_crtc_power_domains() arguments

Pass just the crtc state to modeset_get_crtc_power_domains(). We
can get the crtc from therein.

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190701160550.24205-2-ville.syrjala@linux.intel.com
Reviewed-by: Imre Deak <imre.deak@intel.com>

drm/i915: Check crtc_state->wm.need_postvbl_update before grabbing wm.mutex

wm.mutex does not protect the crtc state so no point in grabbing it
to check crtc_state->wm.need_postvbl_update.

Also do a bit of s/intel_crtc/crtc/ while at it.

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190701160550.24205-1-ville.syrjala@linux.intel.com
Reviewed-by: Imre Deak <imre.deak@intel.com>

drm/i915: Use the "display core" power domain in vlv/chv set_cdclk()

The PFI credit programming performed during cdclk change on vlv/chv
requires access to a register in the disp2d power well. So far
we've abused pipe-A power domain for this, but now we have the
more appropriate "display core" domain so let's make use of it.

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190701161534.6671-1-ville.syrjala@linux.intel.com
Reviewed-by: Imre Deak <imre.deak@intel.com>

drm/i915/selftests: Hold the vma manager lock while modifying mmap_offset

Right idea, wrong lock. We already drop struct_mutex before we free the
mmap_offset when freeing the object, so we need to take the vma manager
lock when manipulating the mmap_offset address space for our selftests.

Fixes: 8221d21b0664 ("drm/i915/selftests: Lock the drm_mm while modifying")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Imre Deak <imre.deak@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190711065215.4004-2-chris@chris-wilson.co.uk

drm/i915/sdvo: Fix handling if zero hbuf size

The spec says:
"A value of 0 indicates that this buffer does not exist"
So we should not convert a hbuf_size of 0 into 1.

Also pull the relevant code into a helper to avoid making the
same mistake multiple times.

And while at it fix the debug prints to not say "hbuf_len" twice.

v2: s/%i/%u/ in the debug (Imre)

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190619180312.31817-1-ville.syrjala@linux.intel.com
Reviewed-by: Imre Deak <imre.deak@intel.com>

drm/i915/guc: Simplify guc client

We originally added support, in some cases partial, for different modes
of operations via guc clients:

- proxy vs direct submission;
- variable engine mask per-client.

We only ever used one flow (all submissions via a single proxy), so the
other code paths haven't been exercised and are most likely
non-functional. The guc firmware interface is also in the process of
being updated to better fit the i915 flow and our client abstraction
will need to change accordingly (or possibly go away entirely), so these
old unused paths can be considered dead and removed.

Signed-off-by: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Michal Wajdeczko <michal.wajdeczko@intel.com>
Cc: Matthew Brost <matthew.brost@intel.com>
Cc: John Harrison <John.C.Harrison@Intel.com>
Acked-by: Matthew Brost <Matthew Brost <matthew.brost@intel.com>
Reviewed-by: Michał Winiarski <michal.winiarski@intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20190710005437.3496-3-daniele.ceraolospurio@intel.com

drm/i915/guc: Remove preemption support for current fw

Preemption via GuC submission is not being supported with its current
legacy incarnation. The current FW does support a similar pre-emption
flow via H2G, but it is class-based instead of being instance-based,
which doesn't fit well with the i915 tracking. To fix this, the
firmware is being updated to better support our needs with a new flow,
so we can safely remove the old code.

v2 (Daniele): resurrect & rebase, reword commit message, remove
preempt_context as well

Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Michal Wajdeczko <michal.wajdeczko@intel.com>
Cc: Matthew Brost <matthew.brost@intel.com>
Cc: John Harrison <John.C.Harrison@Intel.com>
Acked-by: Matthew Brost <matthew.brost@intel.com>
Reviewed-by: Michał Winiarski <michal.winiarski@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190710005437.3496-2-daniele.ceraolospurio@intel.com

drm/i915/selftests: Ensure we don't clamp a random offset to 32b

Specify that we do want a 64b value for sizeof(u32) as we want to
compute the mask of the upper 62bits.

v2: Use round_down() for automatic type promotion

Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190710161413.7115-1-chris@chris-wilson.co.uk

drm/i915/gt: Drop the duplicate icl workaround

The extra w/a was revived in the backmerge that was meant to fix it!

Fixes: 88c90e800675 ("Merge drm/drm-next into drm-intel-next-queued")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190710200428.3275-1-chris@chris-wilson.co.uk

drm/i915/ehl: Enable DDI-D

EHL has four DDI's (DDI-A and DDI-D share combo PHY A).

Cc: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190709183934.445-6-matthew.d.roper@intel.com

drm/i915: Transition port type checks to phy checks

Transition the remaining uses of intel_port_is_* over to the equivalent
intel_phy_is_* functions and drop the port functions.

v5: Fix a call in a debug function that's only called when
    CONFIG_DRM_I915_DEBUG_RUNTIME_PM is on.  (CI)

Cc: José Roberto de Souza <jose.souza@intel.com>
Cc: Lucas De Marchi <lucas.demarchi@intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190709183934.445-5-matthew.d.roper@intel.com

drm/i915/gen11: Convert combo PHY logic to use new 'enum phy' namespace

Convert the code that operates directly on gen11 combo PHY's to use the
new namespace.  Combo PHY registers are those named "ICL_PORT_*" plus
ICL_DPHY_CHKN.

Note that a lot of the PHY programming happens in the MIPI DSI code.
For clarity I've added a for_each_dsi_phy() to loop over the phys used
by DSI.  Since DSI always uses A & B on gen11, port=phy in all cases so
it doesn't actually matter which form we use in the DSI code.  I've used
the phy iterator in code that's explicitly working with the combo PHY,
but left the rest of the DSI code using the port iterator and namespace
to minimize patch deltas.  We can switch the rest of the DSI code over
to use phy terminology later if this winds up being too confusing.

v6: Drop an include of drm/i915_drm.h; that was previously included just
    for the definition of 'enum port' which this patch removes the need
    for.  (Jose)

Cc: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190709183934.445-4-matthew.d.roper@intel.com

drm/i915/gen11: Program ICL_DPCLKA_CFGCR0 according to PHY

Although the register name implies that it operates on DDI's,
DPCLKA_CFGCR0_ICL actually needs to be programmed according to the PHY
that's in use.  I.e., when using EHL's DDI-D on combo PHY A, the bits
described as "port A" in the bspec are what we need to set.  The bspec
clarifies:

        "[For EHL] DDID clock tied to DDIA clock, so DPCLKA_CFGCR0 DDIA
        Clock Select chooses the PLL for both DDIA and DDID and drives
        port A in all cases."

Also, since the CNL DPCLKA_CFGCR0 bit defines are still port-based, we
create separate ICL-specific defines that accept the PHY rather than
trying to share the same bit definitions between CNL and ICL.

v5: Make icl_dpclka_cfgcr0_clk_off() take phy rather than port.  When
    splitting the original patch the hunk to handle this wound up too
    late in the series.  (Sparse)

v6: Since we're already changing this code,
    s/DPCLKA_CFGCR0_ICL/ICL_DPCLKA_CFGCR0/ for consistency.  (Jose)

Bspec: 33148
Cc: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190709183934.445-3-matthew.d.roper@intel.com

drm/i915/gen11: Start distinguishing 'phy' from 'port'

Our past DDI-based Intel platforms have had a fixed DDI<->PHY mapping.
Because of this, both the bspec documentation and our i915 code has used
the term "port" when talking about either DDI's or PHY's; it was always
easy to tell what terms like "Port A" were referring to from the
context.

Unfortunately this is starting to break down now that EHL allows PHY-A
to be driven by either DDI-A or DDI-D.  Is a setup with DDI-D driving
PHY-A considered "Port A" or "Port D?"  The answer depends on which
register we're working with, and even the bspec doesn't do a great job
of clarifying this.

Let's try to be more explicit about whether we're talking about the DDI
or the PHY on gen11+ by using 'port' to refer to the DDI and creating a
new 'enum phy' namespace to refer to the PHY in use.

This patch just adds the new PHY namespace, new phy-based versions of
intel_port_is_*(), and a helper to convert a port to a PHY.
Transitioning various areas of the code over to using the PHY namespace
will be done in subsequent patches to make review easier.  We'll remove
the intel_port_is_*() functions at the end of the series when we
transition all callers over to using the PHY-based versions.

v2:
 - Convert a few more 'port' uses to 'phy.' (Sparse)

v3:
 - Switch DDI_CLK_SEL() back to 'port.' (Jose)
 - Add a code comment clarifying why DPCLKA_CFGCR0_ICL needs to use PHY
   for its bit definitions, even though the register description is
   given in terms of DDI.
 - To avoid confusion, switch CNL's DPCLKA_CFGCR0 defines back to using
   port and create separate ICL+ definitions that work in terms of PHY.

v4:
 - Rebase and resolve conflicts with Imre's TC series.
 - This patch now just adds the namespace and a few convenience
   functions; the important changes are now split out into separate
   patches to make review easier.

Suggested-by: Ville Syrjala <ville.syrjala@linux.intel.com>
Cc: José Roberto de Souza <jose.souza@intel.com>
Cc: Lucas De Marchi <lucas.demarchi@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Imre Deak <imre.deak@intel.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190709183934.445-2-matthew.d.roper@intel.com

drm/i915: move intel_ddi_set_fia_lane_count to intel_tc.c

PORT_TX_DFLEXDPMLE1 is a FIA register so move it to intel_tc.c where we
access other FIA registers. In Tiger Lake we have multiple/modular FIAs
so it makes sense to start moving all access to their registers to a
common place.

While at it, make it clear that we will only ever call this function
for ports with TC phy. Previously we were relying on tc_mode being
TC_PORT_TBT_ALT for combo phy ports. However it's confusing since in
this same function we have checks for is_tc_port. Also, if we manage to
make each phy access only their own field, we may in future add them as
a union inside intel_digital_port.

v2: Fix coding style while moving the code

Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190708172815.6814-4-lucas.demarchi@intel.com

drm/i915: fix include order in intel_tc.*

Separate local includes with a blank line and sort the groups
alphabetically.

v2: don't make intel_tc.h be the first include
v3: don't make local includes be included first

Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190709155403.29370-1-lucas.demarchi@intel.com

drm/i915: make new intel_tc.c use uncore accessors

Let's make the just created intel_tc.c already follow the trend of using
i915 instead of dev_priv and calling the intel_uncore_*() functions.

Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190708172815.6814-2-lucas.demarchi@intel.com

Merge drm/drm-next into drm-intel-next-queued

Catch-up with 5.2. Specially to remove a drm-tip merge
fixup around intel_workarounds.

Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>

drm/i915/icl: Fixed Input CSC Co-efficients for BT601/709

Input CSC Co-efficients for BT601 and BT709 YCbCR to RGB
conversion were slightly off. Fixed the same.

v2: Fixed the co-eficients as there was issue with reference
matrix, spotted by Ville.

v3: Rebase

Signed-off-by: Uma Shankar <uma.shankar@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190628080230.27492-4-uma.shankar@intel.com

drm/i915/icl: Fix Y pre-offset for Full Range YCbCr

Fixed Y Pre-offset in case of Full Range YCbCr.

v2: Rebase

Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Suggested-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Uma Shankar <uma.shankar@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190628080230.27492-3-uma.shankar@intel.com

drm/i915/icl: Handle YCbCr to RGB conversion for BT2020 case

Currently input csc for YCbCR to RGB conversion handles only
BT601 and Bt709. Extending it to support BT2020 as well.

v2: Fixed the co-efficients for LR to FR conversion,
as suggested by Ville.

v3: Fixed Y Pre-offset in case of Full Range YCbCr as suggested
by Ville.

v4: Split the v2 and v3 changes.

v5: Rebase

v6: Fix a rebase fumble.

Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Uma Shankar <uma.shankar@intel.com>
Signed-off-by: Shashank Sharma <shashank.sharma@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190628080230.27492-2-uma.shankar@intel.com

drm/i915/perf: add missing delay for OA muxes configuration

This was dropped from the original patch series, we weren't sure
whether it was needed at the time. More recent tests show it's
definitely needed to have acurate performance data.

Signed-off-by: Lionel Landwerlin <lionel.g.landwerlin@intel.com>
Fixes: 19f81df2859eb1 ("drm/i915/perf: Add OA unit support for Gen 8+")
Acked-by: Chris Wilson <chris@chris-wilson.co.uk>
[ickle: combine duplicate code and comments]
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20190710105524.23017-1-chris@chris-wilson.co.uk

drm/i915/execlists: Record preemption for selftests

Put back the preemption counters lost in commit 22b7a426bbe1
("drm/i915/execlists: Preempt-to-busy") so that our selftests that
assert no preemption took place continue to function.

v2: But a timeslice is only a "soft" preemption!

Fixes: 22b7a426bbe1 ("drm/i915/execlists: Preempt-to-busy")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190710064454.682-1-chris@chris-wilson.co.uk

drm/i915: Remove unused i915_gem_context_lookup_engine

There are no known plans to start using it either.

Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20190709093105.24699-1-tvrtko.ursulin@linux.intel.com

drm/i915: add infrastructure to hold off preemption on a request

We want to set this flag in the next commit on requests containing
perf queries so that the result of the perf query can just be a delta
of global counters, rather than doing post processing of the OA
buffer.

Signed-off-by: Lionel Landwerlin <lionel.g.landwerlin@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
[ickle: add basic selftest for nopreempt]
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190709164227.25859-1-chris@chris-wilson.co.uk

drm/i915: enumerate scratch fields

We have a bunch of offsets in the scratch buffer. As we're about to
add some more, let's group all of the offsets in a common location.

Signed-off-by: Lionel Landwerlin <lionel.g.landwerlin@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20190709123351.5645-6-lionel.g.landwerlin@intel.com

drm/i915/perf: ensure we keep a reference on the driver

The i915 perf stream has its own file descriptor and is tied to
reference of the driver. We haven't taken care of keep the driver
alive.

Signed-off-by: Lionel Landwerlin <lionel.g.landwerlin@intel.com>
Suggested-by: Chris Wilson <chris@chris-wilson.co.uk>
Fixes: eec688e1420da5 ("drm/i915: Add i915 perf infrastructure")
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20190709123351.5645-2-lionel.g.landwerlin@intel.com

drm/i915/userptr: Don't mark readonly objects as dirty

If we map an object as readonly into the GTT, we know that the GPU
cannot have written to it and so the object is not dirty and we don't
need to flush the writes back to the system.

Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190709081718.27843-1-chris@chris-wilson.co.uk

drm/i915/icl: Clear the shared port PLLs from the new crtc state

For consistency clear the icl_port_dplls from the new crtc state, when
releasing the DPLLs from the old crtc state. Leaving them set could
result in releasing the same PLLs multiple times from the same CRTC
state incorrectly (if the same CRTC was first used for a TypeC port then
for a combo PHY port).

Leaving the stale pointers behind happens not to cause a problem atm
(since the incorrect releasing will be a NOP), but we need to fix that
for consistency.

Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190708140735.20198-2-imre.deak@intel.com

drm/i915: Clear the shared PLL from the put_dplls() hook

For symmetry with the get_dplls() hook which sets the shared_dpll
pointer clear the same pointer from the put_dplls() hook.

While at it also constify the old crtc state.

v2:
- Constify the old crtc state. (Ville)

Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190708140735.20198-1-imre.deak@intel.com

drm/i915/sdvo: Add helpers to get the cmd/status string

Add sdvo_cmd_name() and sdvo_cmd_status() helpers to avoid bothering
the callers with the implementation details of the storage for these
strings.

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190619180312.31817-6-ville.syrjala@linux.intel.com
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>

drm/i915/sdvo: Shrink sdvo_cmd_names[] strings

Drop the redundant "SDVO_CMD_" prefix from the command name
strings in sdvo_cmd_names[].

While at it throw away the unused struct name, and undef
SDVO_CMD_NAME_ENTRY() when we're done.

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190619180312.31817-4-ville.syrjala@linux.intel.com
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>

drm/i915/sdvo: Remove duplicate SET_INPUT_TIMINGS_PART1 cmd name string

sdvo_cmd_names[] contains two entries for SET_INPUT_TIMINGS_PART1.
Remove one of them.

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190619180312.31817-3-ville.syrjala@linux.intel.com
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>

drm/i915/sdvo: Use named initializers for the SDVO command names

Use named initializers to make it easier to associate the SDVO debug
prints with the SDVO command defines. Also switch to using ARRAY_SIZE()
instead of assuming that SDVO_CMD_STATUS_SCALING_NOT_SUPP is the last
command type.

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190619180312.31817-2-ville.syrjala@linux.intel.com
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>

drm/i915: Add icl mipi dsi properties

Add scaling and panel orientation properties for
icl mipi dsi.

v2: Add platform specific function (Ville)
v3: Remove redundant check and update scaler call (Jani, Ville)

Signed-off-by: Vandita Kulkarni <vandita.kulkarni@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190627152457.26146-1-vandita.kulkarni@intel.com

drm/i915/hdcp: debug logs for sink related failures

Adding few more debug logs to identify the sink specific HDCP failures
along with a out of mem failure.

v2:
  Capturing the Bug and a-b

Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=110991
Signed-off-by: Ramalingam C <ramalingam.c@intel.com>
Signed-off-by: Uma Shankar <uma.shankar@intel.com>
cc: Daniel Vetter <daniel@ffwll.ch>
Acked-by: Daniel Vetter <daniel@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20190708113319.2517-1-ramalingam.c@intel.com

drm/i915/gt: Remove presumption of RCS0

We now track features correctly instead of probing i915->engine[RCS0]
which is much more flexible and avoids any nasty surprises.

Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190705124325.14270-2-chris@chris-wilson.co.uk

drm/i915/gt: Apply RCS workarounds to the render class

Treat all render engines to the RCS workarounds, simply to avoid using
engine->id when we are trying to think in terms of classes.

Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Stuart Summers <stuart.summers@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190705124325.14270-1-chris@chris-wilson.co.uk

drm/i915/selftests: Fill in a little more of the dummy fence

Initialise the dma_fence innards in preparation for making
dma_fence_signal() always check the callback list.

Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190708113038.19251-1-chris@chris-wilson.co.uk

drm/i915/userptr: Acquire the page lock around set_page_dirty()

set_page_dirty says:

For pages with a mapping this should be done under the page lock
for the benefit of asynchronous memory errors who prefer a
consistent dirty state. This rule can be broken in some special
cases, but should be better not to.

Under those rules, it is only safe for us to use the plain set_page_dirty
calls for shmemfs/anonymous memory. Userptr may be used with real
mappings and so needs to use the locked version (set_page_dirty_lock).

Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=203317
Fixes: 5cc9ed4b9a7a ("drm/i915: Introduce mapping of user pages into video memory (userptr) ioctl")
References: 6dcc693bc57f ("ext4: warn when page is dirtied without buffers")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: stable@vger.kernel.org
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190708140327.26825-1-chris@chris-wilson.co.uk

drm/i915/selftests: Set igt_spinner.gt for early exit

Set up a default gt pointer for an early cleanup of igt_spinnter, before
a request is created and igt_spinner.gt set to the active engine's.

Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190708215524.31639-1-chris@chris-wilson.co.uk

drm/i915: Update DRIVER_DATE to 20190708

Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>

drm/i915/selftests: Reorder error cleanup for whitelist checking

Reorder the error paths so that we unwind all the locals from any error
path and so avoid setting off divers alarum in case we find an error in
case we find an error.

References: https://bugs.freedesktop.org/show_bug.cgi?id=111048
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190708152321.22187-1-chris@chris-wilson.co.uk

drm/i915: Explicitly track active fw_domain timers

Stop guessing over whether we have an extra wakeref held by the delayed
fw put, and track it explicitly for the sake of debug.

Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190708154914.26850-1-chris@chris-wilson.co.uk

drm/i915: Pull assert_forcewake_active() underneath the lock

Make no assumption that something in the background is not acquiring the
fw_domain -- but we still do not track owner so assume that any active
domain is intended by the caller.

Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190707151135.11700-1-chris@chris-wilson.co.uk

drm/i915/gtt: Introduce release_pd_entry

By encapsulating the locking upper level and used check for entry
into a helper function, we can use it in all callsites.

v2: get rid of atomic_reads on lower level clears (Chris)

Cc: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20190705215204.4559-4-chris@chris-wilson.co.uk

drm/i915/gtt: Setup phys pages for 3lvl pdps

If we setup backing phys page for 3lvl pdps, as they
are not used, we will lose 5 pages per ppgtt.

Trading this memory on bsw, we gain more common code paths for all
gen8+ directory manipulation. And those paths are now void of checks
for page directory type, making the hot paths faster.

v2: don't shortcut vm (Chris)

Signed-off-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20190705215204.4559-3-chris@chris-wilson.co.uk

drm/i915/gtt: Tear down setup and cleanup macros for page dma

We don't use common codepaths to setup and cleanup page
directories vs page tables. So their setup and cleanup macros
are of no use and can be removed.

Signed-off-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20190705215204.4559-2-chris@chris-wilson.co.uk

drm/i915/gtt: pde entry encoding is identical

For all page directory entries, the pde encoding is
identical. Don't complicate call sites with different
versions of doing the same thing, so we always check the
existence of physical page before writing the entry into
it. This further generalizes the pd so that manipulation in
callsites will be identical, removing the need to handle
pdps differently for gen8.

v2: squash
v3: inc/dec with set/clear (Chris)
v4: inlines, warn, stray set_pd (Chris)

Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Matthew Auld <matthew.auld@intel.com>
Signed-off-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20190705215204.4559-1-chris@chris-wilson.co.uk

drm/i915: Remove set but not used variable 'intel_dig_port'

Fixes gcc '-Wunused-but-set-variable' warning:

drivers/gpu/drm/i915/display/intel_ddi.c: In function 'intel_ddi_get_config':
drivers/gpu/drm/i915/display/intel_ddi.c:3774:29: warning:
 variable 'intel_dig_port' set but not used [-Wunused-but-set-variable]
  struct intel_digital_port *intel_dig_port;

It is never used, so can be removed.

Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190705113138.65880-1-yuehaibing@huawei.com

drm/i915: Remove set but not used variable 'encoder'

Fixes gcc '-Wunused-but-set-variable' warning:

drivers/gpu/drm/i915/display/intel_dp.c: In function 'intel_dp_set_drrs_state':
drivers/gpu/drm/i915/display/intel_dp.c:6623:24: warning:
 variable 'encoder' set but not used [-Wunused-but-set-variable]

It's never used, so can be removed.Also remove related
variable 'dig_port'

Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190705113112.64715-1-yuehaibing@huawei.com

drm/i915: Order assert forcewake test

Read the current value before computing the expected to ensure that if
the timer does complete early (against our will), it should not cause a
false positive.

v2: The local irq disable did not prevent the timer from running.

Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=111074
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190705074604.16496-1-chris@chris-wilson.co.uk

drm/i915/ehl: Add support for DPLL4 (v10)

This patch adds support for DPLL4 on EHL that include the
following restrictions:

- DPLL4 cannot be used with DDIA (combo port A internal eDP usage).
  DPLL4 can be used with other DDIs, including DDID
  (combo port A external usage).

- DPLL4 cannot be enabled when DC5 or DC6 are enabled.

- The DPLL4 enable, lock, power enabled, and power state are connected
  to the MGPLL1_ENABLE register.

v2: (suggestions from Bob Paauwe)
- Rework ehl_get_dpll() function to call intel_find_shared_dpll() and
  iterate twice: once for Combo plls and once for MG plls.

- Use MG pll funcs for DPLL4 instead of creating new ones and modify
  mg_pll_enable to include the restrictions for EHL.

v3: Fix compilation error

v4: (suggestions from Lucas and Ville)
- Treat DPLL4 as a combo phy PLL and not as MG PLL
- Disable DC states when this DPLL is being enabled
- Reuse icl_get_dpll instead of creating a separate one for EHL

v5: (suggestion from Ville)
- Refcount the DC OFF power domains during the enabling and disabling
  of this DPLL.

v6: rebase

v7: (suggestion from Imre)
- Add a new power domain instead of iterating over the domains
  assoicated with DC OFF power well.

v8: (Ville and Imre)
- Rename POWER_DOMAIN_DPLL4 TO POWER_DOMAIN_DPLL_DC_OFF
- Grab a reference in intel_modeset_setup_hw_state() if this
  DPLL was already enabled perhaps by BIOS.
- Check for the port type instead of the encoder

v9: (Ville)
- Move the block of code that grabs a reference to the power domain
  POWER_DOMAIN_DPLL_DC_OFF to intel_modeset_readout_hw_state() to ensure
  that there is a reference present before this DPLL might get disabled.

v10: rebase

Cc: José Roberto de Souza <jose.souza@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Matt Roper <matthew.d.roper@intel.com>
Cc: Imre Deak <imre.deak@intel.com>
Signed-off-by: Vivek Kasireddy <vivek.kasireddy@intel.com>
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190703230353.24059-1-vivek.kasireddy@intel.com

drm/i915: Clean up skl vs. icl plane formats

Split the format lists for different planes on skl/icl more cleanly.

On skl+ we have just two types of planes: those can do planar and
those that can't.

On icl we have three types of planes: hdr planes, sdr planes that
can do planar, and sdr planes that can't do planar. Those latter two
are the same set of planes we must when choose from when picking the
UV vs. Y plane for planar scanout. So we shall just designate
them sdr uv planes and sdr y planes.

Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190703200824.5971-7-ville.syrjala@linux.intel.com

drm/i915: Cosmetic fix for skl+ plane switch statement

One of the switch cases has the byte order vs. format bits
reversed to all the other cases. Appease the ocd and reorder
them.

Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190703200824.5971-6-ville.syrjala@linux.intel.com

drm/i915: Deal with cpp==8 for g4x watermarks

Docs tell us that on g4x we have to compute the SR watermarks
using 4 bytes per pixel. I'm going to assume that only applies
to 1 and 2 byte per pixel formats, and not 8 byte per pixel
formats. That seems like a recipe for an insufficient watermark
which could lead to underruns. Use the maximum of the two numbers
instead.

Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190703200824.5971-5-ville.syrjala@linux.intel.com

drm/i915: Program plane gamma ramps

All sprite planes have a progammable gamma ramp. Set it up with
a linear ramp on all platforms. This actually matches the reset
value but soon we'll want to reprogram this ramp on some machines,
so let's just set it up across the board.

Note that on pre-IVB the hardware bypasses the gamma unit
unless a YCbCr pixel format is used.

v2: Add parens around << in ilk_linear_gamma()
    Skip gamma programming for RGB on pre-IVB
    s/DVSGAMC/DVSGAMC_G4X/

Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190703200824.5971-4-ville.syrjala@linux.intel.com

drm/i915: Disable sprite gamma on ivb-bdw

We don't currently have any use for the sprite gamma on ivb-bdw.
Let's disable it. We already do that on skl+.

On pre-ivb there is no way to disable the sprite gamma, and it
only affects YCbCr pixel formats, whereas on ivb+ it also
affects RGB formats.

Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190703200824.5971-3-ville.syrjala@linux.intel.com

drm/i915: Add windowing for primary planes on gen2/3 and chv

Plane B and C (note that we don't actually expose plane C currently)
on gen2/3 have a window generator, as does the primary plane on CHV
pipe B. So let's allow positioning of these planes freely within the
pipe source area.

Plane A on gen2/3 seems to have some kind of partial window generator
which would allow you to cut the plane off midway through the scanout,
but it would still have to start at the top-left corner of the pipe,
and it would have to be full width. That's doesn't sound all that
useful, so for simplicity let's just keep to the idea that plane A
has to be fullscreen.

Gen4 removed the plane A/B windowing support entirely, and it wasn't
reintroduced until SKL (apart from the CHV pipe B special case).

v2: s/plane/i9xx_plane/ etc. (James)
v3: Make it less confusing
v4: Deal with IS_GEN()

Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190703200824.5971-2-ville.syrjala@linux.intel.com

drm/i915: Move dev_priv->pm_i{m, e}r into intel_gt

PM interrupts belong to the GT so move the variables to be inside
struct intel_gt.

Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Co-developed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Acked-by: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20190704121756.27824-3-tvrtko.ursulin@linux.intel.com

drm/i915: Remove some legacy mmio accessors from interrupt handling

Mostly in gen11 interrupt handling and a couple neighbouring functions
which were easy since uncore local was already available.

Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Co-developed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Acked-by: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20190704121756.27824-2-tvrtko.ursulin@linux.intel.com

drm/i915: Rework some interrupt handling functions to take intel_gt

Some interrupt handling functions already have gt in their names
suggesting them as obvious candidates to make them take struct intel_gt
instead of i915.

Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Co-developed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Acked-by: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20190704121756.27824-1-tvrtko.ursulin@linux.intel.com

drm/i915: Show instdone for each engine in debugfs

Although polling each engine quickly is preferable as it should give us
a sample of each engine at roughly the same time, keep it simple and
just sample the engine as print out the debug state.

Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Matthew Auld <matthew.auld@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190704200455.14870-3-chris@chris-wilson.co.uk

drm/i915/selftests: Be engine agnostic

When using MI operations, we do not care which engine we use, so use
them all where possible, and where inconvenient double check we have the
engine we selected at random.

v2: Drop the local copy of engine->sseu to avoid an unchecked deref

Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Matthew Auld <matthew.auld@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190704212343.6820-1-chris@chris-wilson.co.uk

drm/i915/overlay: Stash the kernel context on initialisation

Simplify runtime request creation by storing the context we need to use
during initialisation. This allows us to remove one more hardcoded
engine lookup.

Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Matthew Auld <matthew.auld@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190704200455.14870-1-chris@chris-wilson.co.uk

drm/i915/hangcheck: Look at instdone for all engines

It seems intel_engine_get_instdone is able to get instdone for all engines
but intel_hangcheck.c/subunits_stuck decides to ignore it for non render.

We can just drop the check in subunits_stuck since the checks on
unavailable fields will always return stuck, which when bitwise and with
the potential unstuck instdone is harmless.

Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20190703144116.15593-1-tvrtko.ursulin@linux.intel.com

drm/i915/selftests: Drain the freedlists between exec passes

During the context execution tests, we issue a lot of work and discard a
lot of objects without releasing the lock and allowing the background
reaper to free those objects. Insert a small break between each pass to
flush the worker.

Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Matthew Auld <matthew.auld@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190704165317.21060-1-chris@chris-wilson.co.uk

drm/i915/gtt: Mark the freed page table entries with scratch

On unwinding the allocation error path and having freed the page table
entry, it is imperative that we mark it as scratch.

<4> [416.075569] general protection fault: 0000 [#1] PREEMPT SMP PTI
<4> [416.075801] CPU: 0 PID: 2385 Comm: kworker/u2:11 Tainted: G     U            5.2.0-rc7-CI-Patchwork_13534+ #1
<4> [416.076162] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.10.1-0-g8891697-prebuilt.qemu-project.org 04/01/2014
<4> [416.076522] Workqueue: i915 __i915_vm_release [i915]
<4> [416.076754] RIP: 0010:gen8_ppgtt_cleanup_3lvl+0x58/0xb0 [i915]
<4> [416.077023] Code: 81 e2 04 fe ff ff 81 c2 ff 01 00 00 4c 8d 74 d6 58 4d 8b 65 00 4d 3b a7 28 02 00 00 74 40 49 8d 5c 24 50 49 81 c4 50 10 00 00 <48> 8b 2b 49 3b af 20 02 00 00 74 13 4c 89 ff 48 89 ee e8 01 fb ff
<4> [416.077445] RSP: 0018:ffffc9000046bd98 EFLAGS: 00010206
<4> [416.077625] RAX: 0001000000000000 RBX: 6b6b6b6b6b6b6bbb RCX: 8b4b56d500000000
<4> [416.077838] RDX: 00000000000001ff RSI: ffff88805a578008 RDI: ffff88805bd0efc8
<4> [416.078167] RBP: ffff88805bd0efc8 R08: 0000000004e42b93 R09: 0000000000000001
<4> [416.078381] R10: 0000000000000000 R11: ffff888077a1b0b8 R12: 6b6b6b6b6b6b7bbb
<4> [416.078594] R13: ffff88805a578058 R14: ffff88805a579058 R15: ffff88805bd0efc8
<4> [416.078815] FS:  0000000000000000(0000) GS:ffff88807da00000(0000) knlGS:0000000000000000
<4> [416.079395] CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
<4> [416.079851] CR2: 000056160fec2b14 CR3: 0000000071bbc003 CR4: 00000000003606f0
<4> [416.080388] Call Trace:
<4> [416.080828]  gen8_ppgtt_cleanup+0x64/0x100 [i915]
<4> [416.081399]  __i915_vm_release+0xfc/0x1d0 [i915]

Fixes: 1d1b5490b91c ("drm/i915/gtt: Replace struct_mutex serialisation for allocation")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Matthew Auld <matthew.auld@intel.com>
Cc: Mika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: Matthew Auld <matthew.auld@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190704201656.15775-1-chris@chris-wilson.co.uk

drm/i915/gt: Pull engine w/a initialisation into common

We need to setup the workarounds on all engines, with the knowledge
about which platforms each workaround applies to kept together in the
workaround list. As such, we can pull the w/a initialisation into the
common setup and try to avoid duplicating knowledge about when to setup
the workarounds.

Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190703135805.7310-2-chris@chris-wilson.co.uk

drm/i915: Dump w/a lists on all engines

We store separate wa_list on every engine, so be sure to include all
when dumping the current set via debugfs.

Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190703135805.7310-1-chris@chris-wilson.co.uk

drm/i915/guc: Upgrade to GuC 33.0.0

New GuC firmware is available. Let's use it.

Signed-off-by: Michal Wajdeczko <michal.wajdeczko@intel.com>
Cc: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Reviewed-by: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20190703113640.31100-1-michal.wajdeczko@intel.com

drm/i915/gtt: Handle double alloc failures

Matthew pointed out that we could face a double failure with concurrent
allocations/frees, and so the assumption that the local var alloc was
NULL was fraught with danger. Rather than complicate the error paths too
much to add a second local for a second free, just do the second free
earlier on the unwind path.

Reported-by: Matthew Auld <matthew.william.auld@gmail.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Matthew Auld <matthew.william.auld@gmail.com>
Reviewed-by: Matthew Auld <matthew.william.auld@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190704104345.6603-1-chris@chris-wilson.co.uk