ASoC: twl6040: Request core to inline the DAPM sequence

We need to have as less time between McPDM shutdown,
and power down of the DAC on the twl6040 codec as possible.
Request core to ignore the pmdown_time for the playback
stream.
Backround: with the McPDM protocol we are sendning not only
the pure audio stream, but OMAP McPDM also transmits
additional information (for example offset cancellation).
If McPDM is stopped prior to the DAC this information will
be not sent to the codec, which can result noise rendered
by the twl6040 codec.

Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

ASoC: core: Add flag to ignore pmdown_time at pcm_close

With this flag codec drivers can indicate that it is desired
to ignore the pmdown_time for DAPM shutdown sequence when
playback stream is stopped.
The DAPM sequence will be executed without delay in this case.

Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

ASoC: da7210: bugfix for head phone volume control

This patch takes care of reserved bits of headphone volume
register by using correct volume range.

Signed-off-by: Ashish Chavan <ashish.chavan@kpitcummins.com>
Signed-off-by: David Dajun Chen <dchen@diasemi.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

ASoC: ad193x: Fix define of AD193X_PLL_INPUT_MASK

Current code defines AD193X_PLL_INPUT_MASK as (~0x6) which is quite
different from other MASK defines.
To make it consistent with other mask defines, define AD193X_PLL_INPUT_MASK
as 0x6 and change the code accordingly.
I think this change improves the readability.

Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

ASoC: wm8990: Use snd_soc_update_bits for read-modify-write

Use snd_soc_update_bits for read-modify-write register access instead of
open-coding it using snd_soc_read and snd_soc_write

This patch also includes a comment fix in wm8990_set_dai_pll(),
if freq_in and freq_out are 0, what we do is to clear WM8990_PLL_ENA bit.
Thus the comment should be "Turn off PLL".

Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

ASoC: wm8990: Fix wrong bit setting for WM8990_POWER_MANAGEMENT_2

If (fakepower & ((1 << WM8990_INMIXR_PWR_BIT) | (1 << WM8990_AINRMUX_PWR_BIT)))
is false, we should clear WM8990_AINR_ENA bits instead of WM8990_AINL_ENA.

Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

ASoC: wm8400: Fix wrong bit setting for WM8400_POWER_MANAGEMENT_2

If (fakepower & ((1 << WM8400_INMIXR_PWR) | (1 << WM8400_AINRMUX_PWR)))
is false, we should clear WM8400_AINR_ENA bits instead of WM8400_AINL_ENA.

Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

ASoC: wm8991: Use snd_soc_update_bits for read-modify-write

Use snd_soc_update_bits for read-modify-write register access instead of
open-coding it using snd_soc_read and snd_soc_write

Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

ASoC: wm8991: Fix wrong bit setting for WM8991_POWER_MANAGEMENT_2

If (fakepower & ((1 << WM8991_INMIXR_PWR_BIT)|(1 << WM8991_AINRMUX_PWR_BIT))))
is false, we should clear WM8991_AINR_ENA bits instead of WM8991_AINL_ENA.

Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

ASoC: wm8961: Convert codec->hw_read to snd_soc_read

codec->hw_read is broken now, let's covert to snd_soc_read.

Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

ASoC: tlv320aic3x: Convert codec->hw_read to snd_soc_read

codec->hw_read is broken now, let's covert to snd_soc_read.

Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

ASoC: alc5623: Convert codec->hw_read to snd_soc_read

codec->hw_read is broken now, let's covert to snd_soc_read.

Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

ASoC: tlv320aic23: convert to soc-cache

Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

ASoC: Convert DA7210 to table based DAPM init

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

ASoC: tlv320aic32x4: Use snd_soc_update_bits for read-modify-write

Use snd_soc_update_bits for read-modify-write register access instead of
open-coding it using snd_soc_read and snd_soc_write.

Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

ASoC: twl6040: Rename the Earphone Driver event handler

Since the event handler is only used by the Earphone Driver, it is better
to rename it from twl6040_power_mode_event to twl6040_ep_drv_event.

Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

ASoC: twl6040: Change event ordering for Earphone driver

It is better to switch HS Power Mode (if it was in low power mode) before
we enable the Earpiece driver. The switched off EP driver can filter out
noise coming from the Low Power to High Performance transition on the
HSL DAC.

Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

ASoC: twl6040: Remove PLL usage restrictions

There is no limitation dictated by outputs or inputs regarding to the
selected PLL (LP/HP).
Remove the checks for this, and allow all path with any PLL configuration.

Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

ASoC: twl6040: Remove Capture restriction for 17.64MHz sysclk

Capture is supported in all PLL configuration.

Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

ASoC: Update WM5100 accessory detection for revision A

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

ASoC: ak4535: fixup cache register table

ak4535_reg should be 8bit, but cache table is defined as 16bit.

Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@kernel.org

ASoC: ak4642: fixup cache register table

ak4642 register was 8bit, but cache table was defined as 16bit.
ak4642 doesn't work correctry without this patch.

Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@kernel.org

ASoC: sta32x: Write the register default value to cache for reserved registers

Chip documentation explicitly requires that the reset values
of reserved register bits are left untouched.

codec->hw_read is broken now.
Here we use below trick to avoid writing to reserved registers while resume.
Write the register default value to cache for reserved registers,
so the write to the these registers are suppressed by the cache
restore code when it skips writes of default registers.

Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

ASoC: sta32x: Set reg_cache_default to sta32x_regs

Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

ASoC: pxa: Remove redundant snd_soc_dapm_sync() calls from machine drivers

The core will sync DAPM as part of the card initialization, there is no
need for machine drivers to do so during their setup.

Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

ASoC: Make SND_SOC_SAARB and SND_SOC_TAVOREVB3 select MFD_88PM860X

In saarb_pm860x_init() and evb3_pm860x_init(), we call
pm860x_hs_jack_detect() and pm860x_mic_jack_detect() which in turn
calls pm860x_set_bits().
Thus make SND_SOC_SAARB and SND_SOC_TAVOREVB3 select MFD_88PM860X.

This patch fixes below build error if CONFIG_MFD_88PM860X is not configured.

  LD      .tmp_vmlinux1
sound/built-in.o: In function `pm860x_write_reg_cache':
last.c:(.text+0x29e9c): undefined reference to `pm860x_reg_write'
sound/built-in.o: In function `pm860x_set_bias_level':
last.c:(.text+0x29ecc): undefined reference to `pm860x_set_bits'
last.c:(.text+0x29f00): undefined reference to `pm860x_reg_write'
last.c:(.text+0x29f18): undefined reference to `pm860x_reg_write'
sound/built-in.o: In function `pm860x_read_reg_cache':
last.c:(.text+0x29f40): undefined reference to `pm860x_reg_read'
sound/built-in.o: In function `pm860x_probe':
last.c:(.text+0x2a034): undefined reference to `pm860x_bulk_read'
sound/built-in.o: In function `pm860x_codec_handler':
last.c:(.text+0x2a344): undefined reference to `pm860x_reg_read'
last.c:(.text+0x2a354): undefined reference to `pm860x_reg_read'
sound/built-in.o: In function `pm860x_mic_jack_detect':
last.c:(.text+0x2a450): undefined reference to `pm860x_set_bits'
sound/built-in.o: In function `pm860x_hs_jack_detect':
last.c:(.text+0x2a4d0): undefined reference to `pm860x_set_bits'
last.c:(.text+0x2a4f8): undefined reference to `pm860x_set_bits'
last.c:(.text+0x2a510): undefined reference to `pm860x_set_bits'
make: *** [.tmp_vmlinux1] Error 1

Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

ASoC: da7210: Add support for other DAI word lengths, format and mode

This patchs adds support for following,
(1) DAI 20 and 32 bit word sizes
(2) DAI left and right justified formats
(3) DAI slave mode

Signed-off-by: Ashish Chavan <ashish.chavan@kpitcummins.com>
Signed-off-by: David Dajun Chen <dchen@diasemi.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

ASoC: twl6040: Workaround for headset DC offset caused pop noise

Both Headset DAC need to be turned on/off at the same time before
any of the output drivers are enabled (HS Left/Right, Earpiece).
Move the HS DAC enable code to sequenced DAPM_SUPPLY, and attach
it to the DACs.

Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

ASoC: twl6040: Support for vibra output paths

twl6040 have two vibra output drivers.
They can be operated with audio stream coming through
the PDM interface (fifth channel).
The vibra outputs can be controlled via the input/FF
driver as well.
Selection between the two mode is implemented within
the codec driver, the input/FF driver can only operate if
the routing is set to "Input FF".
Changing from "Input FF" to "Audio PDM" mode is protected
as well: The switchin can only be done, if there is no
running effect from the input/FF.

Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Input: twl6040-vibra: Check the selected path for vibra

The VIBSELL/R bit in the VIBCTLL/R register tells the source of the data,
which is going to be used to drive the attached motor(s).
Do not allow effect execution if any of the channels are set to receive
audio data.

Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

MFD: twl6040: function to query the vibra status for clients

If the client only interested, if any of the vibra channels enabled, or
if any of the channels are set to receive audio data via PDM.

This function targets mainly the vibra driver, so it can check if it is
allowed to execute effects ot not.

Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Samuel Ortiz <samuel.ortiz@intel.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

MFD: twl6040: Cache the vibra control registers

The vibra control register will be used from the ASoC codec driver as well.
In order to avoid latency issues caused by I2C read access, cache the two
control register within the core driver, so we do not need to reach out
to the chip to read it back.

Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Samuel Ortiz <samuel.ortiz@intel.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Input: twl6040: Simplify vibra regsiter definitions

The bits within the two control registers (for left and right channel)
are identical.
Use common names for the bits acros the two register.
Also add the missing definition for the path selection bit.

Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

ASoC: da7210: convert to soc-cache

Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

ASoC: Remove impossible case from wm8994_hw_params

We set hw_params callback for wm8994_aif3_dai_ops to wm8994_aif3_hw_params.
Thus no need to check wm8994-aif3 in wm8994_hw_params.

Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

ASoC: Delete ads117x.h

This is not required after multi-component patch.

Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

ASoC: ak4642: convert to soc-cache

Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

ASoC: Instantiate card widgets immediately

This ensures they are available prior to the card late_probe().

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

ASoC: Implement WM5100 accessory detection support

The WM5100 includes an advanced, low power, accessory detect subsystem
capable of detecting both accessory presence and button presses while
the device is in an ultra low power mode. Implement initial support for
this.

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

ASoC: Add missing default for WM5100 Clocking 1

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

ASoC: Fix typo in Kconfig symbol for tlv320aic32x4

It is currently named "TVL" instead of "TLV".

Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Cc: Javier Martin <javier.martin@vista-silicon.com>
Cc: Liam Girdwood <lrg@ti.com>
Cc: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

ASoC: tlv320dac33: Convert to table based init

Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

ASoC: twl4030: Convert to table based init

Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

ASoC: twl6040: Convert to table based init

Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

ASoC: Writing register default value for the reset register

The WM8983 can be reset by performing a write of any value to
the software reset register.
To avoid writing to the software reset register while resume,
we should write the same value in wm8983_reg_defs to software
reset register in wm8983_probe().
The write to the reset register is suppressed by the cache
restore code when it skips writes of default registers.

Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

ASoC: Convert Goni to data based DAPM init

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>

ASoC: sdp3430: Let core to deal with the DAPM widgets

Pass the DAPM widgets/routes via the snd_soc_card struct
to core.

Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Cc: Misael Lopez Cruz <misael.lopez@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

ASoC: osk5912: Let core to deal with the DAPM widgets

Pass the DAPM widgets/routes via the snd_soc_card struct
to core. With this change we do not need the init function
since the remaining snd_soc_dapm_enable_pin calls are
not needed.

Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

ASoC: n810: Let the core to register DAPM widgets/routes and controls

Pass the DAPM widgets/routes and static controls via the
snd_soc_card struct to core. In this way the machine driver
does not need to handle the DAPM widgets/routes.

Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Cc: Jarkko Nikula <jarkko.nikula@bitmer.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

ASoC: am3517evm: Let core to deal with the DAPM widgets

Pass the DAPM widgets/routes via the snd_soc_card struct
to core. With this change we do not need the init function
since the remaining snd_soc_dapm_enable_pin calls are
not needed.

Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Cc: Anuj Aggarwal <anuj.aggarwal@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

ASoC: sdp4430: No need to call dapm_pin_enable at init time

Widgets are connected by default.

Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Cc: Misael Lopez Cruz <misael.lopez@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

ASoC: sdp4430: Let core to deal with the DAPM widgets

Pass the DAPM widgets/routes via the snd_soc_card struct
to core.

Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Cc: Misael Lopez Cruz <misael.lopez@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

ASoC: zoom2: No need to call dapm_pin_enable at init time

Widgets are connected by default.

Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Cc: Misael Lopez Cruz <misael.lopez@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

ASoC: zoom2: Let core to deal with the DAPM widgets

Pass the DAPM widgets/routes via the snd_soc_card struct
to core.

Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Cc: Misael Lopez Cruz <misael.lopez@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

ASoC: OMAP machines: Remove soc_dapm_sync() call from init

No need to call soc_dapm_sync at init time.

Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Cc: Anuj Aggarwal <anuj.aggarwal@ti.com>
Cc: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Cc: Jarkko Nikula <jarkko.nikula@bitmer.com>
Cc: Gražvydas Ignotas <notasas@gmail.com>
Cc: Misael Lopez Cruz <misael.lopez@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

ASoC: Convert Jive to table based init

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Sangbeom Kim <sbkim73@samsung.com>

ASoC: Convert SMDK WM8580 to table based DAPM init

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Sangbeom Kim <sbkim73@samsung.com>

ASoC: Convert SmartQ to table based init

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Sangbeom Kim <sbkim73@samsung.com>

ASoC: Convert RX1950 to table based init

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Sangbeom Kim <sbkim73@samsung.com>

ASoC: Convert H1940 to table based init

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Sangbeom Kim <sbkim73@samsung.com>

ASoC: Convert Simtec machines to table based DAPM init

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

ASoC: fix checkpatch.pl error in omap-mcbsp

Signed-off-by: Michael Opdenacker <michael.opdenacker@linaro.org>
Acked-by: Jarkko Nikula <jarkko.nikula@bitmer.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

ASoC: ak4535: convert to soc-cache

Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

ASoC: wm8988: Convert to snd_soc_cache_sync

Convert to snd_soc_cache_sync for sync reg_cache with the hardware.

Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

ASoC: wm8974: Convert to snd_soc_cache_sync

Convert to snd_soc_cache_sync for sync reg_cache with the hardware.

Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

ASoC: wm8971: Convert to snd_soc_cache_sync

Convert to snd_soc_cache_sync for sync reg_cache with the hardware.

Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

ASoC: wm8960: Convert to snd_soc_cache_sync

Convert to snd_soc_cache_sync for sync reg_cache with the hardware.

Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

ASoC: wm8940: Convert to snd_soc_cache_sync

Convert to snd_soc_cache_sync for sync reg_cache with the hardware.

Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

ASoC: wm8776: Convert to snd_soc_cache_sync

Convert to snd_soc_cache_sync for sync reg_cache with the hardware.

Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

ASoC: wm8750: Convert to snd_soc_cache_sync

Convert to snd_soc_cache_sync for sync reg_cache with the hardware.

Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

ASoC: wm8731: Convert to snd_soc_cache_sync

Convert to snd_soc_cache_sync for sync reg_cache with the hardware.

Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

ASoC: wm8711: Convert to snd_soc_cache_sync

Convert to snd_soc_cache_sync for sync reg_cache with the hardware.

Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

ASoC: wm8510: Convert to snd_soc_cache_sync

Convert to snd_soc_cache_sync for sync reg_cache with the hardware.

Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

ASoC: Fix DAPM sync for TLV320AIC3x custom DAPM widget

We really should be doing this in the core, not in a driver...

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Tested-by: Jarkko Nikula <jarkko.nikula@bitmer.com>

ASoC: Squash error codes from regmap down to -1 on read

The ASoC code always uses -1 as the error code due to reporting errors in
band with the value. Ensure we don't confuse anything by making sure we
don't pass actual error codes back into the rest of the code on read.

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

ASoC: Cache connected input and output recursions

The number of connected input and output endpoints for a given widgets
can't change during a DAPM run so there is no need to redo the recursion
through branches of the tree we've already visited. Doing this on one of
my test systems gives an improvement of:

         Power    Path   Neighbour
Before:  63       607    731
After:   63       141    181

which scales up well as more widgets are involved in paths.

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

ASoC: Assign power_check when we allocate DAPM widgets

This ensures none of the rest of the code ever encounters a widget which
does not have a power check function.

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

ASoC: Ensure all DAPM widgets are instantiated with the card

Specifically for the widgets added by machine driver late probe functions.

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

ASoC: Remove redundant snd_soc_dapm_sync() calls from machine drivers

The core will sync DAPM as part of the card initialization, there is no
need for machine drivers to do so during their setup.

OMAP drivers are omitted as I know Peter already has patches for them.

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

ASoC: Suppress early calls to snd_soc_dapm_sync()

Ensure we only have one sync during the initial startup of the card by
making snd_soc_dapm_sync() a noop on non-instantiated cards. This avoids
any bounces due to things like jacks reporting their initial state on
partially initialised cards. The callers that don't also get called at
runtime should just be removed.

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

regulator: Add WM1811 support

The WM1811 has a slightly different range on LDO2 to other WM8994 class
devices.

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Merge branch 'for-3.1' into for-3.2

ASoC: Return early with -EINVAL if invalid dai format is detected

Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

ASoC: wm8990: Remove incorrect comments

Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

ASoC: wm8990: Convert to snd_soc_cache_sync for sync reg_cache with the hardware

Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

ASoC: fix codec breakage caused by the volsw/volsw_2r merger

By accident few places still uses the _2r calls from
the core.
This is a quick fix, the drivers using the old callbacks
going to be changed.

Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

ASoC: tlv320aic32x4 fix initialization of micpga routing

Checking the pdata-flags used 'or', so the check is always true. Use 'and' to
correctly mask the flags.

Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Cc: Javier Martin <javier.martin@vista-silicon.com>
Cc: Liam Girdwood <lrg@ti.com>
Cc: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

ASoC: Ensure DAPM widgets are set up before we sync jacks

We synchronise jack state on startup - when we do that make sure that we
have set up all the DAPM widgets first in case we end up touching any of
the partially set up widgets when syncing the jack pins.

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Tested-by: Peter Ujfalusi <peter.ujfalusi@ti.com>

ASoC: Replace remaining use of *_volsw_2r with *_volsw

The snd_soc_*_volsw_2r functionality has been merged to
*volsw callbacks.
Few places still used the get, or put variant of volsw_2r,
replace those with the corresponding *_volsw.

Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

ASoC: Remove references to linux@wolfsonmicro.com

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

ASoC: Remove unused variable 'wm9090' in wm9090_probe

Eliminate below build warning:
  CC      sound/soc/codecs/wm9090.o
sound/soc/codecs/wm9090.c: In function 'wm9090_probe':
sound/soc/codecs/wm9090.c:550: warning: unused variable 'wm9090'

Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

ASoC: imx: Remove unused variable 'dai'

Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

ASoC: Remove unused function declaration in imx-ssi.h

These functions are removed in commit f0fba2ad
"ASoC: multi-component - ASoC Multi-Component Support".
Let's remove the leftover function declaration in header file.

Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

ASoC: twl6040: Warn user in twl6040_put_volsw for error case

Let the user know, that the callback has been called with unexpected
register parameter.

Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

ASoC: core: Remove snd_soc_put_volsw_2r definition

We do not have users for snd_soc_put_volsw_2r anymore.
It can be removed.

Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

ASoC: twl6040: Simply call snd_soc_put_volsw form the custom code

The ASoC core now have one callback function, which can handle
single, and double register mixer controls.

Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

ASoC: core: Combine snd_soc_put_volsw/put_volsw_2r functions

Handle the put_volsw/put_volsw_2r in one function.

To avoid build breakage in twl6040 keep the
snd_soc_put_volsw_2r as define, and map it snd_soc_put_volsw.

Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

ASoC: core: Combine snd_soc_get_volsw/get_volsw_2r functions

Handle the get_volsw/get_volsw_2r in one function.

Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

ASoC: core: Combine snd_soc_info_volsw/info_volsw_2r functions

Handle the info_volsw/info_volsw_2r in one function.

Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

ASoC: core: Change SOC_SINGLE/DOUBLE_VALUE representation

SOC_SINGLE/DOUBLE_VALUE is used for mixer controls, where the
bits are within one register.

Assign .rreg to be the same as .reg for these types.

With this change we can tell if the mixer in question:
is mono:
mc->reg == mc->rreg && mc->shift == mc->rshift

is stereo, within single register:
mc->reg == mc->rreg && mc->shift != mc->rshift

is stereo, in two registers:
mc->reg != mc->rreg

The patch provide a small inline function to query, if the mixer
is stereo, or mono.

Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>