wil6210: ADDBA/DELBA flows

Introduce BACK establishment procedures; decision logic is not implemented
yet; debugfs entry 'addba' used to manually trigger addba/delba for ringid 0.

debugfs usage:
to establish BACK with agg_wsize 16:
  echo 16 > /sys/kernel/debug/ieee80211/phy0/wil6210/addba
to delete BACK:
  echo 0 > /sys/kernel/debug/ieee80211/phy0/wil6210/addba
to change agg_wsize, one need to delete BACK and establish it anew

ADDBA flow for:

- originator

Tx side (initiator) sends WMI_VRING_BA_EN_CMDID providing
agg_wsize and timeout parameters.
Eventually, it gets event confirming BACK agreement - WMI_BA_STATUS_EVENTID
with negotiated parameters. On this event, update Tx vring data
(struct vring_tx_data) and display BACK parameters on debugfs

- recipient

Rx side (recipient) firmware informs driver about ADDBA with
WMI_RCP_ADDBA_REQ_EVENTID, driver process it in service work
queue wq_service. It adjusts parameters and sends response
with WMI_RCP_ADDBA_RESP_CMDID, and final confirmation provided
by firmware with WMI_ADDBA_RESP_SENT_EVENTID. In case of success,
driver updates Rx BACK reorder buffer.

policy for BACK parameters:
- aggregation size (agg_wsize * MPDUsize)) to not exceed 64Kbytes

DELBA flow for:

- originator

driver decides to terminate BACK, it sends WMI_VRING_BA_DIS_CMDID
and updates struct vring_tx_data associated with vring; ignore
WMI_DELBA_EVENTID.

- recipient

firmware informs driver with WMI_DELBA_EVENTID,
driver deletes correspondent reorder buffer

ADDBA request processing requires sending WMI command, therefore
it is processed in work queue context. Same work queue used as for
connect, it get renamed to wq_service

Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

ath9k: Add QCA956x HW support

Signed-off-by: Miaoqing Pan <miaoqing@qca.qualcomm.com>
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

ath9k: Fix register definitions for QCA956x

Signed-off-by: Miaoqing Pan <miaoqing@qca.qualcomm.com>
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

ath9k: Add initvals for QCA956x

Signed-off-by: Miaoqing Pan <miaoqing@qca.qualcomm.com>
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

ath9k: Add HW IDs for QCA956x

Signed-off-by: Miaoqing Pan <miaoqing@qca.qualcomm.com>
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

Merge ath-next from ath.git

Major changes in ath10k:

* Device tree support

* Major restructuring how to handle different WMI interface versions

* Add WMI TLV interface in preparation for new firmware interface support

* Support new firmware branch 10.2.4

* Add thermal cooling interface

* Add hwmon interface to read temparture from the device

And of course lots of small fixes and cleanups.

ath10k: fix build error when hwmon is off

kbuild reported a linking error:

ERROR: "devm_hwmon_device_register_with_groups"
[drivers/net/wireless/ath/ath10k/ath10k_core.ko] undefined!

Fix it by returning early and letting the compiler to optimise out the function
call.

Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

rtlwifi: Move macro definitions to core

Several of the drivers still were defining their own copies of various
macros. These are all moved into the core.

Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

rtlwifi: rtl8821ae: Convert driver to use common DM table initialization

Convert driver to use routine rtl_dm_diginit().

Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

rtlwifi: rtl8723be: Convert driver to use common DM table initialization

Convert driver rtl8723be to use routine rtl_dm_diginit().

Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

rtlwifi: rtl8723ae: Convert driver to use common DM table initialization

Convert driver rtl8723ae to use common routine rtl_dm_diginit().

Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

rtlwifi: rtl8192ee: Convert driver to use common DM table initialization

Convert driver rtl8192ee to use the common routine to initialize
dm_digtable.

Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

rtlwifi: rtl8192de: Convert driver to use common DM table initialization

This patch converts driver rtl8192de to use the common routine to
initialize dm_digtable.

Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

rtlwifi: rtl8192c-common: Convert driver to use common DM table initialization

These changes convert both rtl8192ce and rtl8192cu to use the new routine.
Some additional definitions are needed in the core, thus several of the
headers for other drivers are affected, but no other executable code is
changed.

Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

rtlwifi: rtl8188ee: Convert driver to use the common DM table init routine

The previous patch created a routine in rtlwifi to initialize dm_digtable.
Driver rtl8188ee is converted to use that routine.

Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

rtlwifi: Create new routine to initialize the DM tables

Each of the drivers contains a routine that initializes the dm_digtable
member of the driver's private area. As a first step toward reducing the
size of the drivers, a copy of this driver is created in rtlwifi, and the
definitions of the parameters are moved there.

Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

rtlwifi: rtl8723be: Improve modinfo output

The description of the power-save variables for this driver is not as
clear as for the others. The wording is changed to match the others.

Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

rtlwifi: Unify variable naming for all drivers

Some drivers refer to a particular quantity in the driver's private
are by one name, while others use a different name. These differences
are removed.

Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

brcmfmac: get rid of duplicate SDIO device identifiers

Instead of defining SDIO device identifier in brcm80211 code use
the defintions in linux/mmc/sdio_ids.h directly.

Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

wl18xx: declare radar_detect_widths support for ap interfaces

After having all the dfs infrastructure in place, declare
radar_detect_widths support for the ap interfaces combination.

Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

wlcore: add dfs region to reg domain update cmd

Add dfs region to the reg domain channel update command.

Signed-off-by: Guy Mishol <guym@ti.com>
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

wlcore: allow using dfs channels

Since we are going to support dfs channels, there
is no reason to mark them as NO_IR (having
the DFS flag is enough anyway).

Additionally, when setting the regdomain configuration,
enable usable dfs channels.

Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

wlcore: add dfs master restart calls

call wlcore_cmd_dfs_master_restart when starting
the ap on a new channel (after csa is done).

Add a new WLVIF_FLAG_BEACON_DISABLED flag to
indicate that dfs_master_restart command
is required.

Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

wlcore: add support for ap csa

Support ap csa support by implementing the channel_switch_beacon()
mac80211 op.

Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

wl18xx: add debugfs file to emulate radar event

Add debugfs file to emulate radar detection through
a special fw cmd (which in turn will generate radar
event)

Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

wl18xx: add radar detection implementation

Add support for CAC start/stop commands, and pass
radar detection events from the fw to mac80211.

Bump fw name (to wl18xx-fw-4.bin) and min fw version
(to 8.9.*.*.11), and align event mailbox accordingly.

Signed-off-by: Guy Mishol <guym@ti.com>
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

wlcore: enable sleep during AP mode operation

Enable ELP authorization in AP mode and enable the use
of the wakeup bit in the ELP register.

Introduce AP role sleep configuration which is disabled
by default. When configured, it allows the AP to sleep
when ELP is authorized for it.

Signed-off-by: Kobi Leibovitch <kobi.lev100@gmail.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

wlcore: enable AP wowlan

configure wowlan when host is suspended in AP mode,
since the FW can now wake the host up on Rx.

Signed-off-by: Kobi Leibovitch <kobi.lev100@gmail.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

wlcore: add ability to reduce FW interrupts during suspend

Add the ability to mask FW interrupts on RX BA activity, PSM
entry/exit and fast-link notifications. This is used when the host
is suspended in order to decrease redundant wake ups.

Signed-off-by: Ram Amrani <ramrani@ti.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

wlcore/wl18xx: handle rc updates in a separate work

sta_rc_update runs in atomic context. thus, a new work
should be scheduled in order to configure the fw
with the required configuration.

Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

wlcore: fix sparse warning

Use kstrtoul_from_user() for reading the user value,
and fix the following sparse warning:

drivers/net/wireless/ti/wlcore/debugfs.c:937:15: error: incompatible
types in comparison expression (different type sizes)

Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

wlcore: fix WLCORE_VENDOR_ATTR_GROUP_KEY policy

The attribute type is binary data (with max length).

Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

mwifiex: tdls: Use setup_timer

Convert a call to init_timer and accompanying intializations of
the timer's data and function fields to a call to setup_timer.

A simplified version of the semantic match that fixes this problem is as
follows: (http://coccinelle.lip6.fr/)

// <smpl>
@@
expression t,f,d;
@@

-init_timer(&t);
+setup_timer(&t,f,d);
-t.function = f;
-t.data = d;
// </smpl>

Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

mwifiex: 11n_rxreorder: Use setup_timer

Convert a call to init_timer and accompanying intializations of
the timer's data and function fields to a call to setup_timer.

A simplified version of the semantic match that fixes this problem is as
follows: (http://coccinelle.lip6.fr/)

// <smpl>
@@
expression t,f,d;
@@

-init_timer(&t);
+setup_timer(&t,f,d);
-t.function = f;
-t.data = d;
// </smpl>

Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

mwifiex: main: Use setup_timer

Convert a call to init_timer and accompanying intializations of
the timer's data and function fields to a call to setup_timer.

A simplified version of the semantic match that fixes this problem is as
follows: (http://coccinelle.lip6.fr/)

// <smpl>
@@
expression t,f,d;
@@

-init_timer(&t);
+setup_timer(&t,f,d);
-t.function = f;
-t.data = d;
// </smpl>

Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

orinoco_usb: Use setup_timer

Convert a call to init_timer and accompanying intializations of
the timer's data and function fields to a call to setup_timer.

A simplified version of the semantic match that fixes this problem is as
follows: (http://coccinelle.lip6.fr/)

// <smpl>
@@
expression t,f,d;
@@

-init_timer(&t);
+setup_timer(&t,f,d);
-t.function = f;
-t.data = d;
// </smpl>

Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

iwl3945: Use setup_timer

Convert a call to init_timer and accompanying intializations of
the timer's data and function fields to a call to setup_timer.

A simplified version of the semantic match that fixes this problem is as
follows: (http://coccinelle.lip6.fr/)

// <smpl>
@@
expression t,f,d;
@@

-init_timer(&t);
+setup_timer(&t,f,d);
-t.data = d;
-t.function = f;
// </smpl>

Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

iwl4965: Use setup_timer

Convert a call to init_timer and accompanying intializations of
the timer's data and function fields to a call to setup_timer.

A simplified version of the semantic match that fixes this problem is as
follows: (http://coccinelle.lip6.fr/)

// <smpl>
@@
expression t,f,d;
@@

-init_timer(&t);
+setup_timer(&t,f,d);
-t.data = d;
-t.function = f;
// </smpl>

Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

cw1200: queue: Use setup_timer

Convert a call to init_timer and accompanying intializations of
the timer's data and function fields to a call to setup_timer.

A simplified version of the semantic match that fixes this problem is as
follows: (http://coccinelle.lip6.fr/)

// <smpl>
@@
expression t,f,d;
@@

-init_timer(&t);
+setup_timer(&t,f,d);
-t.data = d;
-t.function = f;
// </smpl>

Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

cw1200: main: Use setup_timer

Convert a call to init_timer and accompanying intializations of
the timer's data and function fields to a call to setup_timer.

A simplified version of the semantic match that fixes this problem is as
follows: (http://coccinelle.lip6.fr/)

// <smpl>
@@
expression t,f,d;
@@

-init_timer(&t);
+setup_timer(&t,f,d);
-t.data = d;
-t.function = f;
// </smpl>

Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

wireless: cw1200: Use setup_timer

Convert a call to init_timer and accompanying intializations of
the timer's data and function fields to a call to setup_timer.

A simplified version of the semantic match that fixes this problem is as
follows: (http://coccinelle.lip6.fr/)

// <smpl>
@@
expression t,f,d;
@@

-init_timer(&t);
+setup_timer(&t,f,d);
-t.data = d;
-t.function = f;
// </smpl>

Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

rt2x00: use helper to check capability/requirement

Use rt2x00_has_cap_flag macro to check rt2x00dev->cap_flags.

Signed-off-by: Fred Chou <fred.chou.nd@gmail.com>
Acked-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

wil6210: use 'uint64_t' instead of 'cycles_t' to avoid warnings

do_div() checks the type strictly. 'cycles_t' may be 32-bit under quite
a few architectures (parisc, arm, avr32 ...). So use 'uint64_t' instead
of, the related warning (with allmodconfig under parisc):

    CC [M]  drivers/net/wireless/ath/wil6210/debugfs.o
  In file included from arch/parisc/include/generated/asm/div64.h:1:0,
                   from include/linux/kernel.h:124,
                   from include/linux/list.h:8,
                   from include/linux/module.h:9,
                   from drivers/net/wireless/ath/wil6210/debugfs.c:17:
  drivers/net/wireless/ath/wil6210/debugfs.c: In function ‘wil_vring_debugfs_show’:
  include/asm-generic/div64.h:43:28: warning: comparison of distinct pointer types lacks a cast
    (void)(((typeof((n)) *)0) == ((uint64_t *)0)); \
                              ^
  drivers/net/wireless/ath/wil6210/debugfs.c:107:4: note: in expansion of macro ‘do_div’
      do_div(idle, total);
      ^
  In file included from include/uapi/linux/stddef.h:1:0,
                   from include/linux/stddef.h:4,
                   from ./include/uapi/linux/posix_types.h:4,
                   from include/uapi/linux/types.h:13,
                   from include/linux/types.h:5,
                   from include/linux/list.h:4,
                   from include/linux/module.h:9,
                   from drivers/net/wireless/ath/wil6210/debugfs.c:17:
  include/asm-generic/div64.h:44:18: warning: right shift count >= width of type [-Wshift-count-overflow]
    if (likely(((n) >> 32) == 0)) {   \
                    ^
  include/linux/compiler.h:159:40: note: in definition of macro ‘likely’
   # define likely(x) __builtin_expect(!!(x), 1)
                                          ^
  drivers/net/wireless/ath/wil6210/debugfs.c:107:4: note: in expansion of macro ‘do_div’
      do_div(idle, total);
      ^
  In file included from arch/parisc/include/generated/asm/div64.h:1:0,
                   from include/linux/kernel.h:124,
                   from include/linux/list.h:8,
                   from include/linux/module.h:9,
                   from drivers/net/wireless/ath/wil6210/debugfs.c:17:
  include/asm-generic/div64.h:48:22: warning: passing argument 1 of ‘__div64_32’ from incompatible pointer type [-Wincompatible-pointer-types]
     __rem = __div64_32(&(n), __base); \
                        ^
  drivers/net/wireless/ath/wil6210/debugfs.c:107:4: note: in expansion of macro ‘do_div’
      do_div(idle, total);
      ^
  include/asm-generic/div64.h:35:17: note: expected ‘uint64_t * {aka long long unsigned int *}’ but argument is of type ‘cycles_t * {aka long unsigned int *}’
   extern uint32_t __div64_32(uint64_t *dividend, uint32_t divisor);
                   ^

Signed-off-by: Chen Gang <gang.chen.5i5j@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

mwifiex: Add support for wowlan disconnect

This patch adds support for wowlan disconnect.

Signed-off-by: Maithili Hinge <maithili@marvell.com>
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

mwifiex: Move code for wowlan magic-packet and patterns to a function

This patch moves code for wowlan magic-packet and patterns to a function
mwifiex_set_mef_filter.

Signed-off-by: Maithili Hinge <maithili@marvell.com>
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

mwifiex: Increase priority of firmware download message

When driver is loaded, it is important to know if FW was already
active or it is freshly downloaded. This patch increases the
priority of these messages.

Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

mwifiex: do not release lock during list_for_each_entry_safe()

As we are releasing the lock, during next iteration we may end
up getting page fault if other thread has already deleted that
node.

Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

mwifiex: wakeup pending wait queues

Wakeup pending wait queues in unload path. This will help to avoid
soft lockup issues in corner cases.

Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

mwifiex: add wakeup timer based recovery mechanism

If host fails to wakeup the firmware, we will trigger card reset
after 3 second timeout.

Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

mwifiex: increase delay during card reset

200ms is the requirement to allow VDD1.1 and VDD1.8 to
drop to have proper reset.

Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Marc Yang <yangyang@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

mwifiex: Adjust calling place of mwifiex_terminate_workqueue

Workqueue needs to be flushed early when removing card, otherwise
soft lockup issue may happen because main_process is triggered by
interrupt while card is being removed.

Signed-off-by: Marc Yang <yangyang@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

mwifiex: remove redundant flag MWIFIEX_HW_STATUS_FW_READY

This flag is never set but checked at two places. We will get rid of
this code.

Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

mwifiex: get supported BA stream info from FW

This patch adds support to get number of BA streams
supported information from FW. Some newer chips(e.g. 8897 series)
support 4 BA streams for TX; so driver should not disallow BA stream
setup just after 2 streams have been established.

Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

mwifiex: make tx packet 64 byte DMA aligned

This patch adds support for DMA alignment of 64 bytes for TX packets.

Signed-off-by: Xinming Hu <huxm@marvell.com>
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

mwifiex: do not send key material cmd when delete wep key

This patch fixes memory corruption reported by community developer.

"Memory corruption occurs in mwifiex_ret_802_11_key_material_v1()
when a short command response is received without a key length
causing non initialised memory to be interpreted as the key
length resulting in a memcpy() overwriting the part of the
driver's private data structure beyond the key area."

For v1 key material API firmwares, there is no need to send
command to delete WEP key. WEP encryption/decryption is controlled
by mac_control command.

This patch avoids sending key material command in del_key case.

Reported-by: Martin Fuzzey <mfuzzey@parkeon.com>
Signed-off-by: Xinming Hu <huxm@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

mwifiex: enable -D__CHECK_ENDIAN__ for sparse by default

Enable the endian checks by default.

Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

brcmfmac: Add support for bcm43340/1 wireless chipsets

This patch adds support for the bcm43340 and bcm43341 wireless
chipsets. These two chipsets are identical from wireless parts
perspective. As such they use the same firmware image.

Cc: Samuel Ortiz <sameo@linux.intel.com>
Cc: Rob Herring <rob.herring@linaro.org>
Signed-off-by: John Stultz <john.stultz@linaro.org>
[arend@broadcom.com: squash to single commit, remove 43341 chipid]
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

mwifiex: module parameter for deep sleep configuration

This patch adds module parameter for auto deepsleep configuration.
By default, module_param is 0 and auto deep sleep is enabled.
If mwifiex driver is loaded with disable_auto_ds=1, deep sleep
configuration would not be downloaded to FW and FW would not enter
deepsleep upon initializing.

Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

mwifiex: save sdio register values before firmware dump

This patch saves sdio registers value before firmware dump,
this can be used to find out reason for FW dump.

Signed-off-by: Xinming Hu <huxm@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

mwifiex: save driver information to file when firmware dump

This patch adds support to dump driver information to a file
when firmware dump happens. This information can be used to
root casue FW crash.

Signed-off-by: Xinming Hu <huxm@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

mwifiex: move debug_data dump function to common utililty file

mwifiex_debug_info also need be save to file when firmware dump happens.
Move its dump implementation function to commmon utilility file, thus it
can be reused in firmware dump function.

Signed-off-by: Xinming Hu <huxm@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

mwifiex: move pm_wakeup_card_complete definition to usb.c

Move mwifiex_pm_wakeup_card_complete handler to source file.

Signed-off-by: Xinming Hu <huxm@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

mwifiex: add rx histogram statistics support

This patch add a new debugfs item histogram used for reporting
rx data packet statitics(rx rate, snr, noise floor, signal strenth)
to userspace.

Signed-off-by: Xinming Hu <huxm@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

mwifiex: add bcn_rcv_cnt and bcn_miss_cnt in getlog debugfs

This patch add receive beacon count and miss beacon count statistics
in debugfs getlog item.

Signed-off-by: Xinming Hu <huxm@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

mwifiex: report tdls peers in debugfs

This patch add provision to show TDLS peer table in debugfs file.

Signed-off-by: Xinming Hu <huxm@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

ath5k: drop owner assignment from platform_drivers

This platform_driver does not need to set an owner, it will be populated by the
driver core.

Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

brcmfmac: enable 802.11d support in firmware

When the driver gets beacon info containing a country IE from user-space
upon .start_ap() callback, it will enable regulatory 802.11d support.

Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

brcmfmac: signal completion of 802.1x.

Use cfg80211 change_station to signal the completion of 802.1x
to firmware. This allows FW to take appropriate actions.

Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

brcmfmac: follow user-space regulatory domain selection

When user-space uses a valid ISO-3166-1 country code for its
regulatory domain selection, the driver will try to configure
the firmware to use the same.

Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

brcmfmac: Change error log in standard log for rxbufpost.

When there is no room in the ring for rxbufpost an error is logged,
however this happens quite frequently and can be considered normal
and is certainly recoverable. This patch changes the erorr into
a normal msgbuf log.

Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

brcmfmac: Fix WEP configuration for AP mode.

When a device is configured for AP mode and it is configured for
WEP then the keys are plumbed first, followed by AP configuration.
During configuration a down command is given to the firmware which
will clear the configured keys. This patch reprograms the WEP keys
after AP has been brought up.

Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

brcmfmac: remove unused/duplicate defines in chip.c

The source file chip.c contained some duplicate defines and
some unused ones. Removing them.

Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

brcmfmac: Fix incorrect casting of 64 bit physical address.

The physical addresses being used by pcie and msgbuf were using
a cast to long, which incorrectly caused it to limit the address
to 32bit. Now explicit u64 is used where needed.

Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

Merge tag 'iwlwifi-next-for-kalle-2014-12-30' of https://git./linux/kernel/git/iwlwifi/iwlwifi-next

* more work on d0i3 power state
* enhancements to the firmware debugging infrastructure
* support for 2 concurrent channel contexts
* fixes / cleanups in the rate control
* general cleanups

Merge branch 'timecounter-next'

Richard Cochran says:

====================
Fixing the "Time Counter fixes and improvements"

For this series I had only tested the build with ARCH=x86 and arm, but
others like sparc64, microblaze, powerpc, and s390 will fail because
they somehow don't indirectly include clocksource.h for the drivers in
question.

This series fixes the build issues reported by:
 kbuild test robot <fengguang.wu@intel.com>
====================

Signed-off-by: David S. Miller <davem@davemloft.net>

microblaze: include the new timecounter header.

The timecounter/cyclecounter code has moved, so users need the new include.

Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

mlx4: include clocksource.h again

This driver uses the function, clocksource_khz2mult, and so it really must
include clocksource.h.

Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

ixgbe: convert to CYCLECOUNTER_MASK macro.

Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

igb: convert to CYCLECOUNTER_MASK macro.

Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

e1000e: convert to CYCLECOUNTER_MASK macro.

Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

bnx2x: convert to CYCLECOUNTER_MASK macro.

Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

timecounter: provide a macro to initialize the cyclecounter mask field.

There is no need for users of the timecounter/cyclecounter code to include
clocksource.h just for a single macro.

Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

MAINTAINERS: Update Open vSwitch entry.

OVS development is moved to netdev mailing list. Update tree and
list in MAINTAINERS file.

Signed-off-by: Pravin B Shelar <pshelar@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge tag 'wireless-drivers-next-for-davem-2015-01-02' of git://git./linux/kernel/git/kvalo/wireless-drivers-next

Changes:

* ath9k: enable Transmit Power Control (TPC) for ar9003 chips

* rtlwifi: cleanup and updates from the vendor driver

* rsi: fix memory leak related to firmware image

* ath: parameter fix for FCC DFS pattern

Signed-off-by: David S. Miller <davem@davemloft.net>

net: ethernet: cisco: enic: enic_dev: Remove some unused functions

Removes some functions that are not used anywhere:
enic_dev_enable2_done() enic_dev_enable2() enic_dev_deinit_done()
enic_dev_init_prov2() enic_vnic_dev_deinit()

This was partially found by using a static code analysis program called cppcheck.

Signed-off-by: Rickard Strandqvist <rickard_strandqvist@spectrumdigital.se>
Signed-off-by: David S. Miller <davem@davemloft.net>

isdn: hisax: hfc4s8s_l1: Remove some unused functions

Removes some functions that are not used anywhere:
Read_hfc32() Write_hfc32() Write_hfc16()

This was partially found by using a static code analysis program called cppcheck.

Signed-off-by: Rickard Strandqvist <rickard_strandqvist@spectrumdigital.se>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: fddi: skfp: smt.c: Remove unused function

Remove the function smt_ifconfig() that is not used anywhere.

This was partially found by using a static code analysis program called cppcheck.

Signed-off-by: Rickard Strandqvist <rickard_strandqvist@spectrumdigital.se>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: ethernet: chelsio: cxgb3: mc5.c: Remove some unused functions

Removes some functions that are not used anywhere:
dbgi_rd_rsp3() dbgi_wr_addr3()

This was partially found by using a static code analysis program called cppcheck.

Signed-off-by: Rickard Strandqvist <rickard_strandqvist@spectrumdigital.se>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: skbuff: don't zero tc members when freeing skb

Not needed, only four cases:
 - kfree_skb (or one of its aliases).
   Don't need to zero, memory will be freed.
 - kfree_skb_partial and head was stolen:  memory will be freed.
 - skb_morph:  The skb header fields (including tc ones) will be
   copied over from the 'to-be-morphed' skb right after
   skb_release_head_state returns.
 - skb_segment:  Same as before, all the skb header
   fields are copied over from the original skb right away.

Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge branch 'for-upstream' of git://git./linux/kernel/git/bluetooth/bluetooth-next

Johan Hedberg say:

====================
pull request: bluetooth-next 2014-12-31

Here's the first batch of bluetooth patches for 3.20.

 - Cleanups & fixes to ieee802154  drivers
 - Fix synchronization of mgmt commands with respective HCI commands
 - Add self-tests for LE pairing crypto functionality
 - Remove 'BlueFritz!' specific handling from core using a new quirk flag
 - Public address configuration support for ath3012
 - Refactor debugfs support into a dedicated file
 - Initial support for LE Data Length Extension feature from Bluetooth 4.2

Please let me know if there are any issues pulling. Thanks.
====================

Signed-off-by: David S. Miller <davem@davemloft.net>

geneve: Add Geneve GRO support

This results in an approximately 30% increase in throughput
when handling encapsulated bulk traffic.

Signed-off-by: Joe Stringer <joestringer@nicira.com>
Signed-off-by: Jesse Gross <jesse@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: Add Transparent Ethernet Bridging GRO support.

Currently the only tunnel protocol that supports GRO with encapsulated
Ethernet is VXLAN. This pulls out the Ethernet code into a proper layer
so that it can be used by other tunnel protocols such as GRE and Geneve.

Signed-off-by: Jesse Gross <jesse@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net/fsl: remove hardcoded clock setting from xgmac_mdio

There is no need to set the clock speed in read/write which will be performed
unnecessarily for each mdio access. Init it during probe is enough.

Also, the hardcoded clock value is not a proper way for all SoCs.

Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net/fsl: remove irq assignment from xgmac_mdio

Which is wrong and not used, so no extra space needed by
mdiobus_alloc_size(), use mdiobus_alloc() instead.

Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net/fsl: remove reset from xgmac_mdio

Since the reset is just clock setting, individual mdio reset is
not available.

Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge branch 'gmac-next'

Roger Chen says:

====================
support GMAC driver for RK3288

Roger Chen (6):
  patch1: add driver for Rockchip RK3288 SoCs integrated GMAC
  patch2: define clock ID used for GMAC
  patch3: modify CRU config for Rockchip RK3288 SoCs integrated GMAC
  patch4: dts: rockchip: add gmac info for rk3288
  patch5: dts: rockchip: enable gmac on RK3288 evb board
  patch6: add document for Rockchip RK3288 GMAC

Tested on rk3288 evb board:
Execute the following command to enable ethernet,
set local IP and ping a remote host.

busybox ifconfig eth0 up
busybox ifconfig eth0 192.168.1.111
ping 192.168.1.1
====================

Signed-off-by: David S. Miller <davem@davemloft.net>

GMAC: add document for Rockchip RK3288 GMAC

The document descripts how to add properties for GMAC in device tree.

change since v2:

1. remove power-gpio, reset-gpio, phyirq-gpio, pmu_regulator setting
2. add "snps,reset-gpio", "snps,reset-active-low;" "snps,reset-delays-us"

Signed-off-by: Roger Chen <roger.chen@rock-chips.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

ARM: dts: rockchip: enable gmac on RK3288 evb board

enable gmac in rk3288-evb-rk808.dts

changes since v2:
1. add fixed regulator for PHY
2. remove power-gpio, reset-gpio, phyirq-gpio, pmu_regulator setting
3. add "snps,reset-gpio", "snps,reset-active-low;" "snps,reset-delays-us"

Signed-off-by: Roger Chen <roger.chen@rock-chips.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

ARM: dts: rockchip: add gmac info for rk3288

add gmac info in rk3288.dtsi for GMAC driver

changes since v2:
1. add drive-strength in the pinctrl settings

Signed-off-by: Roger Chen <roger.chen@rock-chips.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

GMAC: modify CRU config for Rockchip RK3288 SoCs integrated GMAC

modify CRU config for GMAC driver

changes since v2:
1. remove SCLK_MAC_PLL

Signed-off-by: Roger Chen <roger.chen@rock-chips.com>
Signed-off-by: David S. Miller <davem@davemloft.net>