Pawel Dembicki [Mon, 18 Mar 2024 09:49:55 +0000 (10:49 +0100)]
ppfe-firmware: Bump to lf-6.6.3-1.0.0
Bump ppfe-firmware package to lf-6.6.3-1.0.0
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
Pawel Dembicki [Mon, 18 Mar 2024 09:47:48 +0000 (10:47 +0100)]
ls-rcw: Bump to lf-6.6.3-1.0.0
Bump ls-rcw package to lf-6.6.3-1.0.0.
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
Pawel Dembicki [Mon, 18 Mar 2024 09:44:47 +0000 (10:44 +0100)]
ls-ddr-phy: bump to lf-6.6.3-1.0.0
Bump ls-ddr-phy to version lf-6.6.3-1.0.0.
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
Pawel Dembicki [Mon, 18 Mar 2024 09:42:15 +0000 (10:42 +0100)]
fman-ucode: Bump to lf-6.6.3-1.0.0
Bump fman-ucode to version lf-6.6.3-1.0.0.
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
INAGAKI Hiroshi [Wed, 8 Mar 2023 12:54:14 +0000 (21:54 +0900)]
mvebu: add support for Fortinet FortiWiFi 51E
Fortinet FortiWiFi 51E (FWF-51E) is a UTM with 1x WLAN and 1x SSD, based
on Armada 385 (
88F6820).
Specification:
- SoC : Marvell Armada 385
88F6820
- RAM : DDR3 2 GiB (4x Micron MT41K512M8DA-107, "D9SGQ")
- Flash : SPI-NOR 128 MiB (Macronix MX66L1G45GMI-10G)
- SSD : mSATA SSD 32 GB (A-DATA XM21E (AXM21ES3-32GM-B))
- mode : SATA III 6Gbps
- power : 3.3 VDC, 3.1 W (Max.)
- Ethernet : 7x 10/100/1000 Mbps
- LAN 1-5 : Marvell
88E6176
- WAN 1, 2 : Marvell
88E1512 (2x)
- WLAN : Fortinet EMP7618-FT (Atheros AR9382 (2T2R))
- interface : MiniPCIe
- LEDs/Keys : 18x/1x
- UART : "CONSOLE" port (RJ-45, RS-232C level)
- port : ttyS0
- settings : 9600bps 8n1
- assignment : 1:NC , 2:NC , 3:TXD, 4:GND,
5:GND, 6:RXD, 7:NC , 8:NC
- note : compatible with Cisco console cable
- HW Monitoring: nuvoTon NCT7802Y
- Power : 12 VDC, 2 A
- plug : Molex 5557-02R
Flash instruction using initramfs image:
1. Power on FWF-51E and interrupt to show bootmenu
2. Call "[I]: System information." -> "[S]: Set serial port baudrate."
and set baudrate to 9600 bps
3. Call "[R]: Review TFTP parameters.", check TFTP parameters and
connect computer to "Image download port" in the parameters
4. Prepare TFTP server with the parameters obtained above
5. Rename OpenWrt initramfs image to "image.out" and put to TFTP
directory
6. Call "[T]: Initiate TFTP firmware transfer." to download initramfs
image from TFTP server
7. Type "R" key when the following message is showed, to boot initramfs
image without flashing to spi-nor flash
"Save as Default firmware/Backup firmware/Run image without saving:[D/B/R]?"
8. On initramfs image, backup mtd if needed
minimum:
- "firmware-info"
- "kernel"
- "rootfs"
9. On initramfs image, upload sysupgrade image to the device and perform
sysupgrade
10. Wait ~200 seconds to complete flashing and rebooting.
If the device is booted with stock firmware, login to bootmenu and
call "[B]: Boot with backup firmware and set as default." to set the
first OS image as default and boot it.
Notes:
- Both colors of Bi-color LEDs on the front panel cannot be turned on at
the same time.
- "PWR" and "Logo" LEDs are connected to power source directly.
- The following partitions are added for OpenWrt.
These partitions are contained in "uboot" partition (0x0-0x1fffff) on
stock firmware.
- "firmware-info"
- "dtb"
- "u-boot-env"
- "board-info"
Image header for bootmenu tftp:
0x0 - 0xf : ?
0x10 - 0x2f : Image Name
0x30 - 0x17f: ?
0x180 - 0x183: Kernel Offset*
0x184 - 0x187: Kernel Length*
0x188 - 0x18b: RootFS Offset (ext2)*
0x18c - 0x18f: RootFS Length (ext2)*
0x190 - 0x193: DTB Offset
0x194 - 0x197: DTB Length
0x198 - 0x19b: Data Offset (jffs2)
0x19c - 0x19f: Data Length (jffs2)
0x1a0 - 0x1ff: ?
*: required for initramfs image
MAC addresses:
(eth0): 90:6C:AC:xx:xx:98 (board-info (OpenWrt), 0xd880 (hex))
WAN 1 : 90:6C:AC:xx:xx:99
WAN 2 : 90:6C:AC:xx:xx:9A
LAN 1 : 90:6C:AC:xx:xx:9B
LAN 2 : 90:6C:AC:xx:xx:9C
LAN 3 : 90:6C:AC:xx:xx:9D
LAN 4 : 90:6C:AC:xx:xx:9E
LAN 5 : 90:6C:AC:xx:xx:9F
WLAN : 88:DC:96:xx:xx:xx (MiniPCIe Card)
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Tested-by: Raylynn Knight <rayknight@me.com>
INAGAKI Hiroshi [Wed, 8 Mar 2023 12:54:14 +0000 (21:54 +0900)]
mvebu: add support for Fortinet FortiWiFi 50E-2R
Fortinet FortiWiFi 50E-2R (FWF-50E-2R) is a UTM with 2x WLAN, based on
Armada 385 (
88F6820).
Specification:
- SoC : Marvell Armada 385
88F6820
- RAM : DDR3 2 GiB (4x Nanya NT5CC512M8EN-EK)
- Flash : SPI-NOR 128 MiB (Macronix MX66L1G45GMI-10G)
- Ethernet : 7x 10/100/1000 Mbps
- LAN 1-5 : Marvell
88E6176
- WAN 1, 2 : Marvell
88E1512 (2x)
- WLAN : Gemtek WMDQ-177ACN (Qualcomm Atheros QCA9892 (2T2R))
(2x)
- interface : MiniPCIe
- LEDs/Keys : 18x/1x
- UART : "CONSOLE" port (RJ-45, RS-232C level)
- port : ttyS0
- settings : 9600bps 8n1
- assignment : 1:NC , 2:NC , 3:TXD, 4:GND,
5:GND, 6:RXD, 7:NC , 8:NC
- note : compatible with Cisco console cable
- HW Monitoring: nuvoTon NCT7802Y
- Power : 12 VDC, 2.5 A
- plug : Molex 5557-02R
Flash instruction using initramfs image:
1. Power on FWF-50E-2R and interrupt to show bootmenu
2. Call "[I]: System information." -> "[S]: Set serial port baudrate."
and set baudrate to 9600 bps
3. Call "[R]: Review TFTP parameters.", check TFTP parameters and
connect computer to "Image download port" in the parameters
4. Prepare TFTP server with the parameters obtained above
5. Rename OpenWrt initramfs image to "image.out" and put to TFTP
directory
6. Call "[T]: Initiate TFTP firmware transfer." to download initramfs
image from TFTP server
7. Type "R" key when the following message is showed, to boot initramfs
image without flashing to spi-nor flash
"Save as Default firmware/Backup firmware/Run image without saving:[D/B/R]?"
8. On initramfs image, backup mtd if needed
minimum:
- "firmware-info"
- "kernel"
- "rootfs"
9. On initramfs image, upload sysupgrade image to the device and perform
sysupgrade
10. Wait ~200 seconds to complete flashing and rebooting.
If the device is booted with stock firmware, login to bootmenu and
call "[B]: Boot with backup firmware and set as default." to set the
first OS image as default and boot it.
Notes:
- Both colors of Bi-color LEDs on the front panel cannot be turned on at
the same time.
- "PWR" and "Logo" LEDs are connected to power source directly.
- The following partitions are added for OpenWrt.
These partitions are contained in "uboot" partition (0x0-0x1fffff) on
stock firmware.
- "firmware-info"
- "dtb"
- "u-boot-env"
- "board-info"
Image header for bootmenu tftp:
0x0 - 0xf : ?
0x10 - 0x2f : Image Name
0x30 - 0x17f: ?
0x180 - 0x183: Kernel Offset*
0x184 - 0x187: Kernel Length*
0x188 - 0x18b: RootFS Offset (ext2)*
0x18c - 0x18f: RootFS Length (ext2)*
0x190 - 0x193: DTB Offset
0x194 - 0x197: DTB Length
0x198 - 0x19b: Data Offset (jffs2)
0x19c - 0x19f: Data Length (jffs2)
0x1a0 - 0x1ff: ?
*: required for initramfs image
MAC addresses:
(eth0): 90:6C:AC:xx:xx:98 (board-info (OpenWrt), 0xd880 (hex))
WAN 1 : 90:6C:AC:xx:xx:99
WAN 2 : 90:6C:AC:xx:xx:9A
LAN 1 : 90:6C:AC:xx:xx:9B
LAN 2 : 90:6C:AC:xx:xx:9C
LAN 3 : 90:6C:AC:xx:xx:9D
LAN 4 : 90:6C:AC:xx:xx:9E
LAN 5 : 90:6C:AC:xx:xx:9F
WLAN 1: 1C:49:7B:xx:xx:xx (MiniPCIe Card)
WLAN 2: 1C:49:7B:xx:xx:xx (MiniPCIe Card)
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Tested-by: Raylynn Knight <rayknight@me.com>
INAGAKI Hiroshi [Wed, 8 Mar 2023 12:54:14 +0000 (21:54 +0900)]
mvebu: add support for Fortinet FortiGate 52E
Fortinet FortiGate 52E (FG-52E) is a UTM, based on Armada 385 (
88F6820).
Specification:
- SoC : Marvell Armada 385
88F6820
- RAM : DDR3 2 GiB (4x Micron MT41K512M8DA-107, "D9SGQ")
- Flash : SPI-NOR 128 MiB (Macronix MX66L1G45GMI-10G)
- SSD : mSATA SSD 64 GB (2x A-DATA XM21E (AXM21ES3-32GM-B))
- mode : SATA III 6Gbps
- power : 3.3 VDC, 3.1 W (Max.)
- Ethernet : 7x 10/100/1000 Mbps
- LAN 1-5 : Marvell
88E6176
- WAN 1, 2 : Marvell
88E1512 (2x)
- LEDs/Keys : 18x/1x
- UART : "CONSOLE" port (RJ-45, RS-232C level)
- port : ttyS0
- settings : 9600bps 8n1
- assignment : 1:NC , 2:NC , 3:TXD, 4:GND,
5:GND, 6:RXD, 7:NC , 8:NC
- note : compatible with Cisco console cable
- HW Monitoring: nuvoTon NCT7802Y
- Power : 12 VDC, 2.5 A
- plug : Molex 5557-02R
Flash instruction using initramfs image:
1. Power on FG-52E and interrupt to show bootmenu
2. Call "[I]: System information." -> "[S]: Set serial port baudrate."
and set baudrate to 9600 bps
3. Call "[R]: Review TFTP parameters.", check TFTP parameters and
connect computer to "Image download port" in the parameters
4. Prepare TFTP server with the parameters obtained above
5. Rename OpenWrt initramfs image to "image.out" and put to TFTP
directory
6. Call "[T]: Initiate TFTP firmware transfer." to download initramfs
image from TFTP server
7. Type "R" key when the following message is showed, to boot initramfs
image without flashing to spi-nor flash
"Save as Default firmware/Backup firmware/Run image without saving:[D/B/R]?"
8. On initramfs image, backup mtd if needed
minimum:
- "firmware-info"
- "kernel"
- "rootfs"
9. On initramfs image, upload sysupgrade image to the device and perform
sysupgrade
10. Wait ~200 seconds to complete flashing and rebooting.
If the device is booted with stock firmware, login to bootmenu and
call "[B]: Boot with backup firmware and set as default." to set the
first OS image as default and boot it.
Notes:
- Both colors of Bi-color LEDs on the front panel cannot be turned on at
the same time.
- "PWR" and "Logo" LEDs are connected to power source directly.
- The following partitions are added for OpenWrt.
These partitions are contained in "uboot" partition (0x0-0x1fffff) on
stock firmware.
- "firmware-info"
- "dtb"
- "u-boot-env"
- "board-info"
Image header for bootmenu tftp:
0x0 - 0xf : ?
0x10 - 0x2f : Image Name
0x30 - 0x17f: ?
0x180 - 0x183: Kernel Offset*
0x184 - 0x187: Kernel Length*
0x188 - 0x18b: RootFS Offset (ext2)*
0x18c - 0x18f: RootFS Length (ext2)*
0x190 - 0x193: DTB Offset
0x194 - 0x197: DTB Length
0x198 - 0x19b: Data Offset (jffs2)
0x19c - 0x19f: Data Length (jffs2)
0x1a0 - 0x1ff: ?
*: required for initramfs image
MAC addresses:
(eth0): 90:6C:AC:xx:xx:98 (board-info (OpenWrt), 0xd880 (hex))
WAN 1 : 90:6C:AC:xx:xx:99
WAN 2 : 90:6C:AC:xx:xx:9A
LAN 1 : 90:6C:AC:xx:xx:9B
LAN 2 : 90:6C:AC:xx:xx:9C
LAN 3 : 90:6C:AC:xx:xx:9D
LAN 4 : 90:6C:AC:xx:xx:9E
LAN 5 : 90:6C:AC:xx:xx:9F
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
INAGAKI Hiroshi [Sat, 20 Jan 2024 06:34:41 +0000 (15:34 +0900)]
mvebu: add support for Fortinet FortiGate 51E
Fortinet FortiGate 51E (FG-51E) is a UTM, based on Armada 385 (
88F6820).
Specification:
- SoC : Marvell Armada 385
88F6820
- RAM : DDR3 2 GiB (4x Micron MT41K512M8DA-107, "D9SGQ")
- Flash : SPI-NOR 128 MiB (Macronix MX66L1G45GMI-10G)
- SSD : mSATA SSD 32 GB (A-DATA XM21E (AXM21ES3-32GM-B))
- mode : SATA III 6Gbps
- power : 3.3 VDC, 3.1 W (Max.)
- Ethernet : 7x 10/100/1000 Mbps
- LAN 1-5 : Marvell
88E6176
- WAN 1, 2 : Marvell
88E1512 (2x)
- LEDs/Keys : 18x/1x
- UART : "CONSOLE" port (RJ-45, RS-232C level)
- port : ttyS0
- settings : 9600bps 8n1
- assignment : 1:NC , 2:NC , 3:TXD, 4:GND,
5:GND, 6:RXD, 7:NC , 8:NC
- note : compatible with Cisco console cable
- HW Monitoring: nuvoTon NCT7802Y
- Power : 12 VDC, 2.5 A
- plug : Molex 5557-02R
Flash instruction using initramfs image:
1. Power on FG-51E and interrupt to show bootmenu
2. Call "[I]: System information." -> "[S]: Set serial port baudrate."
and set baudrate to 9600 bps
3. Call "[R]: Review TFTP parameters.", check TFTP parameters and
connect computer to "Image download port" in the parameters
4. Prepare TFTP server with the parameters obtained above
5. Rename OpenWrt initramfs image to "image.out" and put to TFTP
directory
6. Call "[T]: Initiate TFTP firmware transfer." to download initramfs
image from TFTP server
7. Type "R" key when the following message is showed, to boot initramfs
image without flashing to spi-nor flash
"Save as Default firmware/Backup firmware/Run image without saving:[D/B/R]?"
8. On initramfs image, backup mtd if needed
minimum:
- "firmware-info"
- "kernel"
- "rootfs"
9. On initramfs image, upload sysupgrade image to the device and perform
sysupgrade
10. Wait ~200 seconds to complete flashing and rebooting.
If the device is booted with stock firmware, login to bootmenu and
call "[B]: Boot with backup firmware and set as default." to set the
first OS image as default and boot it.
Notes:
- Both colors of Bi-color LEDs on the front panel cannot be turned on at
the same time.
- "PWR" and "Logo" LEDs are connected to power source directly.
- The following partitions are added for OpenWrt.
These partitions are contained in "uboot" partition (0x0-0x1fffff) on
stock firmware.
- "firmware-info"
- "dtb"
- "u-boot-env"
- "board-info"
Image header for bootmenu tftp:
0x0 - 0xf : ?
0x10 - 0x2f : Image Name
0x30 - 0x17f: ?
0x180 - 0x183: Kernel Offset*
0x184 - 0x187: Kernel Length*
0x188 - 0x18b: RootFS Offset (ext2)*
0x18c - 0x18f: RootFS Length (ext2)*
0x190 - 0x193: DTB Offset
0x194 - 0x197: DTB Length
0x198 - 0x19b: Data Offset (jffs2)
0x19c - 0x19f: Data Length (jffs2)
0x1a0 - 0x1ff: ?
*: required for initramfs image
MAC addresses:
(eth0): 70:4C:A5:xx:xx:98 (board-info (OpenWrt), 0xd880 (hex))
WAN 1 : 70:4C:A5:xx:xx:99
WAN 2 : 70:4C:A5:xx:xx:9A
LAN 1 : 70:4C:A5:xx:xx:9B
LAN 2 : 70:4C:A5:xx:xx:9C
LAN 3 : 70:4C:A5:xx:xx:9D
LAN 4 : 70:4C:A5:xx:xx:9E
LAN 5 : 70:4C:A5:xx:xx:9F
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Tested-by: Raylynn Knight <rayknight@me.com>
INAGAKI Hiroshi [Tue, 5 Dec 2023 13:15:38 +0000 (22:15 +0900)]
mvebu: separate common parts to new dtsi for FortiGate/FortiWiFi 5xE
Add a new dtsi which contains the common parts of Fortinet
FortiGate/FortiWiFi 5xE series devices.
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
INAGAKI Hiroshi [Tue, 5 Dec 2023 13:15:38 +0000 (22:15 +0900)]
mvebu: separate common parts to new dtsi for FortiGate/FortiWiFi 3xE
Add a new dtsi which contains the common parts of Fortinet
FortiGate/FortiWiFi 3xE series devices.
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
INAGAKI Hiroshi [Tue, 5 Dec 2023 13:15:38 +0000 (22:15 +0900)]
mvebu: rename common dtsi of FortiGate 30E/50E
Rename the common dtsi of Fortinet FortiGate 30E/50E for the preparation
of adding support for the other FortiGate/FortiWiFi 3xE/5xE devices.
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
INAGAKI Hiroshi [Mon, 4 Dec 2023 12:02:13 +0000 (21:02 +0900)]
mvebu: add common image definition for FortiGate devices
Add a common definition of Fortinet FortiGate devices to
image/cortexa9.mk for a preparation of adding support for
other FortiGate 3xE/5xE devices.
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Kristian Skramstad [Wed, 17 Apr 2024 13:14:59 +0000 (15:14 +0200)]
ath79: qca9563: add support for Amplifi Router HD
Hardware:
SoC: Qualcomm Atheros QCA956X ver 1 rev 0
CPU clock: 775.000 MHz
Memory: 128 MB DDR2
Flash: 32 MB SPI NOR mx25l25635e
Switch: Atheros AR8327 rev. 4
Ethernet: 5x 10/100/1000 Mbps (1 WAN + 4 LAN)
Buttons: 1x Reset
Serial: TX, RX, GND, VCC
Baudrate: 115200
Wifi: Qualcomm Atheros qca988x 802.11ac/n - 3x3
Qualcomm Atheros AR9561 802.11b/g/n - 3x3
Not working:
Leds: 1x via a SPI controller
Display: ST7789V or ILI9341V
controlled by stm32f205.
Note:
DSA changes are ready, but we have an issue with
ports not working after 20-30 minutes. So for now
we use swconfig.
Installation: serial connection only
There is a J11 four pin connector. You need to connect TX, RX and GND.
You can find very good information about the device here
https://github.com/alexanderhenne/AFi-R?tab=readme-ov-file#finding-j11
Upgrading via serial port:
1. Download the kernel initramfs image. Copy the image to a TFTP server
2. Connect to console on the AP, and connect the LAN1 port to your PC LAN
3. Stop autoboot to get to U-boot shell
Interrupt the autoboot process by pressing any key when prompted
4. Transfer the kernel image with TFTP
Set your ip address on your TFTP server to 192.168.1.254
# tftpboot 0x81000000 amplifi-router-hd-initramfs-kernel.bin
5. Load the image
# bootm 0x81000000
6. SCP sysupgrade image from your PC to the Amplifi HD
(If you use a newer mac use scp -O)
# scp openwrt-ath79-generic-ubnt_amplifi-router-hd-squashfs-sysupgrade.bin root@192.168.1.1:/tmp/
7. Write sysupgrade to the firmware partition
# mtd write /tmp/openwrt-ath79-generic-ubnt_amplifi-router-hd-squashfs-sysupgrade.bin firmware
8. Reboot your device
# reboot
Credit to alexanderhenne for all the information.
Signed-off-by: Kristian Skramstad <kristian+github@83.no>
INAGAKI Hiroshi [Sat, 11 May 2024 06:35:50 +0000 (15:35 +0900)]
ramips: add support for ELECOM WRC-X1800GS
ELECOM WRC-X1800GS is a 2.4/5 GHz band 11ax (Wi-Fi 6) router, based on
MT7621A.
Specification:
- SoC : MediaTek MT7621A
- RAM : DDR3 256 MiB
- Flash : RAW-NAND 128 MiB (Macronix MX30LF1G28AD-TI)
- WLAN : 2.4/5 GHz 2T2R (MediaTek MT7915D)
- Ethernet : 5x 10/100/1000 Mbps
- switch : MediaTek MT7530 (SoC)
- LEDs/Keys (GPIO) : 7x/4x
- UART : pin-header on PCB ("J5")
- arrangement : 3.3V, TX, RX, NC, GND from tri-angle marking
- settings : 115200n8
- Power : 12 VDC, 1 A
Flash instruction using initramfs-factory image:
1. Boot WRC-X1800GS normally with "Router" mode
2. Access to "http://192.168.2.1/" and open firmware update page
("ファームウェア更新")
3. Select the OpenWrt initramfs-factory image and click apply ("適用")
button
4. After flashing initramfs-factory image and reboot, upload the
sysupgrade image and perform sysupgrade with it
5. Wait ~120 seconds to complete flashing
Notes:
- WRC-X1800GS has 2x os images. Those are switched on every firmware
updating on stock firmware, but dual-boot feature on this device
cannot be handled on OpenWrt. So the 1st image is always used on
OpenWrt.
This is controlled by "bootnum" variable embedded in "persist"
partition (addr: 0x4).
- WRC-X1800GS has 2x HW revisions. There are some small changes, but the
same DeviceTree in stock firmware is used for both revisions.
On this support of WRC-X1800GS, 2x green:wlan-2g-N LEDs are defined
for each revision and the same default triggers are set.
MAC addresses:
LAN : 38:97:A4:xx:xx:38 (Factory, 0x1fdfa (hex) / Ubootenv, ethaddr (text))
WAN : 38:97:A4:xx:xx:3B (Factory, 0x1fdf4 (hex))
2.4 GHz: 38:97:A4:xx:xx:39
5 GHz : 38:97:A4:xx:xx:3A
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
INAGAKI Hiroshi [Sat, 11 May 2024 05:14:16 +0000 (14:14 +0900)]
ramips: parameterize some values in Build/znet-header
Parameterize magic number and header length to use the device-specific
values.
example:
On WRC-X1800GS, an additional ELECOM-specific header and a magic number
"COMC" are required.
Stock FW v1.18:
$ hexdump -n $((0x40080)) -C wrc-x1800gs_v1.18.bin
00000000 45 4c 45 43 4f 4d 00 00 57 52 43 2d 58 31 38 30 |ELECOM..WRC-X180|
00000010 30 47 53 00 00 00 00 00 00 00 00 00 00 00 00 00 |0GS.............|
00000020 00 00 00 00 00 00 00 00 31 2e 31 38 00 00 00 00 |........1.18....|
00000030 00 00 00 00 00 00 00 00 43 4f 4d 43 04 00 ac 00 |........COMC....|
00000040 40 f0 49 74 b1 e8 6a ca e4 20 65 1f 34 2e 30 34 |@.It..j.. e.4.04|
00000050 28 58 56 46 2e 31 29 62 31 37 00 00 00 00 00 00 |(XVF.1)b17......|
00000060 00 00 00 00 00 00 00 00 ff ff ff ff ff ff ff ff |................|
00000070 ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff |................|
*
00040000 d0 0d fe ed 00 36 9c c0 00 00 00 38 00 36 9a e0 |.....6.....8.6..|
00040010 00 00 00 28 00 00 00 11 00 00 00 10 00 00 00 00 |...(............|
00040020 00 00 00 6c 00 36 9a a8 00 00 00 00 00 00 00 00 |...l.6..........|
00040030 00 00 00 00 00 00 00 00 00 00 00 01 00 00 00 00 |................|
00040040 00 00 00 03 00 00 00 04 00 00 00 62 65 54 97 8f |...........beT..|
00040050 00 00 00 03 00 00 00 28 00 00 00 00 4d 49 50 53 |.......(....MIPS|
00040060 20 4f 70 65 6e 57 72 74 20 46 49 54 20 28 46 6c | OpenWrt FIT (Fl|
00040070 61 74 74 65 6e 65 64 20 49 6d 61 67 65 20 54 72 |attened Image Tr|
00040080
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
INAGAKI Hiroshi [Sat, 11 May 2024 08:05:10 +0000 (17:05 +0900)]
uboot-envtools: add support for ELECOM WRC-X1800GS
Add support for ELECOM WRC-X1800GS on uboot-envtools, to update
bootmenu_delay variable on sysupgrade.
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Akshay Bhat [Fri, 19 Apr 2024 18:26:45 +0000 (11:26 -0700)]
build: fix version info in cyclonedx sbom
Prior
e8725a932e16eaf6ec51add8c084d959cbe32ff2, version used to be
VERSION:=$(PKG_VERSION)-$(PKG_RELEASE)
After
e8725a932e16eaf6ec51add8c084d959cbe32ff2, the version is:
VERSION:=$(PKG_VERSION)-r$(PKG_RELEASE)
Hence the gen_*_cyclonedxsbom functions need to be updated to remove
the trailing -r prefix in the version in order to generate correct
version info in the SBOM.
Signed-off-by: Akshay Bhat <nodeax@gmail.com>
Ryan Castellucci [Mon, 6 May 2024 14:12:10 +0000 (15:12 +0100)]
ipq40xx: eap1300: add eap1300ext as alt model
The EnGenius EAP1300 and EAP1300EXT use identical boards and firmware
(as flashed) from the vendor.
As with the EAP1300, the EAP1300EXT requires a specific firmware version
to flash OpenWRT. Unfortunately, the required firmware is truncated on
the vendor's website.
A working file can be created as follows:
```
curl \
https://www.engeniustech.com/wp_firmware/eap1300-all-v3.5.3.5_c1.9.04.bin \
| perl -pe 's/\x09EAP1300_A/\x0cEAP1300EXT_A/' \
> eap1300ext-all-v3.5.3.5_c1.9.04.bin
```
The file should have sha256:
`
58a1197a426139a12b03fd432334e677124cbe3384349bd7337f2ee71f1dcfd4`.
Please see commit
2b4ac79 for further
details.
The vendor firmware must be decrypted before it can be flashed from
OpenWRT. A tool able to do that is available from:
https://github.com/ryancdotorg/enfringement/blob/main/decrypt.py
Signed-off-by: Ryan Castellucci <code@ryanc.org>
Leon M. Busch-George [Fri, 17 May 2024 18:10:25 +0000 (20:10 +0200)]
mediatek: filogic: prevent faulty mac address assignment
The vendor U-Boot on the Cudy M3000 and the Yuncore AX835 assign random
mac addresses on boot and set the 'local-mac-address' property which
prevents Openwrt from assigning the correct address from evmem.
This patch removes the alias for ethernet0 so that U-Boot doesn't add the
property, removes the workaround from 02_network, and adds back the nvmem
definition for the M3000.
Signed-off-by: Leon M. Busch-George <leon@georgemail.eu>
Linus Walleij [Tue, 21 May 2024 07:30:28 +0000 (09:30 +0200)]
ixp4xx: Add back support for D-Link DSM G600 A
OpenWrt supported the D-Link DSM G600 A in the past. It has
64 MB of RAM and 16 MB of flash so it will run just fine,
and should be quite usable with a rootfs on an external
harddrive.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Linus Walleij [Mon, 20 May 2024 20:05:13 +0000 (22:05 +0200)]
ixp4xx: Add back support for Freecom FSG-3
OpenWrt supported the Freecom FSG-3 in the past. It has
64 MB of RAM so will run fine, but the bare 4 MB of flash
makes it a non-default target. The generated compressed
image is currently below 4MB (just 3.3 MB) though, so it
should be possible to flash just fine with a rootfs on
a harddrive or USB stick, which is what the FSG-3 used
in the past as well.
The device has a WAN port on eth0 and three LAN ports on
eth1. The LAN ports are probably a DSA switch but the
old OpenWrt base never activated that, instead it relies
on boot defaults.
Due to questionable usablity without tweaking and further
work this image is not built by default, but made available
for developers who know what they are doing.
The TAR+CRC image generation is a rewritten version of the
earlier support code.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Linus Walleij [Mon, 20 May 2024 19:32:55 +0000 (21:32 +0200)]
ixp4xx: Add back support for Iomega NAS100D
OpenWrt supported the Iomega NAS100D in the past and it has
64 MB of RAM so if booted from a harddrive it will probably
work just fine. The APEX boot loader already has a build
variant for this machine that we can just pick up and use.
This device has a single ethernet port so bring this online
with DHCP as expected for a NAS device.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Linus Walleij [Tue, 21 May 2024 07:28:56 +0000 (09:28 +0200)]
ixp4xx: Add ext4 and rootfs-part to features
Several of the IXP4xx machines mount root on external harddrives
so add EXT4 and rootfs-part to the featureset so the right
features are always selected.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Daniel Golle [Fri, 24 May 2024 21:38:34 +0000 (22:38 +0100)]
uboot-mediatek: fix white-space in package Makefile
Replace accidental spaces with tabs.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Daniel Golle [Sat, 25 May 2024 02:52:41 +0000 (03:52 +0100)]
uboot-mediatek: refresh patches
Patch 290-mt7981-add-USB-nodes.patch needs a refresh.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Daniel Golle [Fri, 19 Apr 2024 16:51:51 +0000 (17:51 +0100)]
mediatek: filogic: add Adtran SmartRG Mount Stuart series
Common specifications:
* Mediatek MT7988A (4x Cortex-A73, up to 1.8 GHz clock speed)
* 8 GiB eMMC
* 2 GiB DDR4 RAM
* 1x 10000M/1000M/100M + 3x 1000M/100M/10M LAN ports
* MT7996 Tri-band (2.4G, 5G, 6G) 4T4R 802.11be Wi-Fi
* Airoha AG3352 GPS
* Renesas DA14531MOD Bluetooth
* 2 buttons (Reset, Mesh/WPS)
* uC-controlled RGB LED via I2C
* 2x LED for each 1G port, 3x LED for each 10G port
* USB 3.0 type A port
* 3.3V-level 115200 baud UART console via 4-pin Dupont connector
exposed at the bottom of the device
* USB-C PD power input
SDG-8733: 1x 10000M/1000M/100M WAN port
SDG-8734: 1x USXGMII/10GBase-R/5GBase-R/2500Base-X/1000Base-X/SGMII SFP+
Both models are also available in versions including 2x FXS POTS interfaces
for analog phones. Those interfaces are not supported by OpenWrt.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Daniel Golle [Sat, 20 Apr 2024 01:59:31 +0000 (02:59 +0100)]
mediatek: fix sysupgrade config backup on Adtran SmartRG devices
Add missing call to emmc_copy_config which either writes the sysupgrade
tar.gz backup file or clears the existing rootfs_data overlay.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Daniel Golle [Fri, 10 May 2024 23:48:57 +0000 (00:48 +0100)]
generic: 6.6: backports and add LED support for Aquantia PHYs
Backport patch adding support for the AQR114C PHY and add support for
PHY LEDs and polarity setting of Aquantia 3rd and 4th generation PHYs.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Andrey Bondar [Fri, 10 May 2024 13:22:14 +0000 (16:22 +0300)]
ath79: add support for 8Devices Carambola3 board
Carambola3 is a WiFi module based on Qualcomm/Atheros QCA4531
http://wiki.8devices.com/carambola3
Specification:
- 650/600/216 MHz (CPU/DDR/AHB)
- 128 MB of RAM (DDR2)
- 32 MB of FLASH
- 2T2R 2.4 GHz
- 2x 10/100 Mbps Ethernet
- 1x USB 2.0 Host socket
- UART for serial console
- 12x GPIO
Flash instructions:
Upgrading from ar71xx target:
- Upload image into the board:
scp openwrt-ath79-generic-8dev_carambola3-squashfs-sysupgrade.bin \
root@192.168.1.1/tmp/
- Run sysupgrade
sysupgrade -F /tmp/openwrt-ath79-generic-8dev_carambola3-squashfs-sysupgrade.bin
Upgrading from u-boot:
- Set up tftp server with openwrt-ath79-generic-8dev_carambola3-initramfs-kernel.bin
- Go to u-boot (reboot and press ESC when prompted)
- Set TFTP server IP
setenv serverip 192.168.1.254
- Set device ip from the same subnet
setenv ipaddr 192.168.1.1
- Copy new firmware to board
tftpboot 0x82000000 initramfs.bin
- Boot OpenWRT
bootm 0x82000000
- Upload image openwrt-ath79-generic-8dev_carambola3-squashfs-sysupgrade.bin into the board
- Run sysupgrade.
Signed-off-by: Andrey Bondar <a.bondar@8devices.com>
Link: https://github.com/openwrt/openwrt/pull/15514
Signed-off-by: Robert Marko <robimarko@gmail.com>
Rany Hany [Mon, 13 May 2024 13:34:22 +0000 (16:34 +0300)]
linux-atm: fix build with GCC 14
Basic changes to make linux-atm build without any issues with GCC 14.
Besides some errors caused by -Wpointer-sign, there was also an issue
with socklen_t not being used for getsockopt() and accept()
sometimes.
I also updated the Debian patch to include the latest changes from
version "1:2.5.1-5.1" in Debian Sid. This allowed me to drop
"600-fix-format-errors.patch" and "700-include_sockios.patch".
Signed-off-by: Rany Hany <rany_hany@riseup.net>
Didier 'OdyX' Raboud [Wed, 15 May 2024 07:49:05 +0000 (09:49 +0200)]
usbmode: add Huawei E5785
This 4G/LTE modem is a WiFi hotspot, and also works as cdc_ether modem
when plugged over USB. It needs usb-modeswitching. With HuaweiNewMode,
it will modeswitch from 3426:1f01 (mass-storage) to 3426:14db
(cdc_ether).
Signed-off-by: Didier 'OdyX' Raboud <odyx@raksha.ch>
Link: https://github.com/openwrt/openwrt/pull/15497
Signed-off-by: Robert Marko <robimarko@gmail.com>
Lea Teuberth [Tue, 2 Apr 2024 09:30:32 +0000 (11:30 +0200)]
ramips: add support for TP-Link Archer MR200v5
Specifications:
CPU: MT7628AN 580MHz
RAM: 64MB DDR2
FLASH: 8MB EN25QH64 NOR SPI
WIFI: 2.4GHz 2x2 MT7628 b/g/n internal
WIFI: 5GHz 1x1 MT7610E ac/n PCI
LTE: Qualcomm MDM9207
ETH: 4xLAN 100base-T integrated
SWITCH: RT3050-ESW Port 0,1,2,3: LAN, Port 6: CPU
LEDS: LAN, WAN, Power, 3x signal strength, WiFi
BTNS: Reset, WiFi toggle
UART: Near ETH ports, Vcc-GND-RX-TX, 115200, 8N1
Installation:
1. Update using recovery mode
- set your IP to 192.168.0.225, subnet mask: 255.255.255.0
- start tftp server, rename tftp-recovery.bin to
tp_recovery.bin and place it into the server's directory
- while holdig the "reset" button, power on the device
- keep holding "reset" until the file is being transferred
Notes:
This board has only one MAC address programmed
in the "romfile" partition:
- MAC for phy0 (2.4GHz) at romfile 0xf100 (0)
- MAC for phy1 (5GHz) at romfile 0xf100 (-1)
- stock firmware re-uses phy0 MAC for ethernet
- stock firmware uses romfile 0xf100 (1) for WWAN;
not used since QMI interface is raw IP
Signed-off-by: Lea Teuberth <lea.teuberth@outlook.com>
Rafał Miłecki [Mon, 22 Apr 2024 21:13:11 +0000 (23:13 +0200)]
mediatek: include "kmod-mt7915e" package per device
mt7915e driver supports MT7915 & MT7916 devices and MT7981 & MT7986
on-SoC wireless controllers. Devices based on MT7988 and possibly other
next chipsets are quite unlikely to need it (MT7988 was designed to be
used with MT7996).
Move kmod-mt7915e to DEVICE_PACKAGES of relevant devices.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Rosen Penev [Sat, 18 May 2024 19:14:20 +0000 (12:14 -0700)]
tools: refresh all patches
Refresh all tools patches now that tools/refresh correctly works.
CI now checks for them and actively complain if tools have unrefreshed
patches.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
[ reword commit message ]
Link: https://github.com/openwrt/openwrt/pull/15524
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Rosen Penev [Wed, 22 May 2024 21:14:23 +0000 (14:14 -0700)]
tools/lz4: remove patches
meson is used to build it since
291b137. No need to patch Makefiles.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/15524
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Daniel Golle [Wed, 22 May 2024 14:19:45 +0000 (16:19 +0200)]
build: generate private key for APK early
Other than OPKG which only uses signed package list, APK uses
individually signed packages in addition to signed package lists. Hence,
in order to be able to generate package, the private key needs to be
generated before compiling packages. Express that dependency and
generate the private key before building any packages instead of doing
so as part of the base-files package build.
Fixes: d788ab376f ("build: add APK package build capabilities")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Robert Marko [Wed, 22 May 2024 14:55:51 +0000 (16:55 +0200)]
ipq40xx: dont panic on PSGMII calibration fail
Currently, in case that PSGMII calibration fails it will panic the kernel
which is not ideal and is preventing any debugging to be done.
So, since PGMII calibration failing only means that wired networking wont
work lets convet the panic() call to dev_error.
Link: https://github.com/openwrt/openwrt/pull/15542
Signed-off-by: Robert Marko <robimarko@gmail.com>
Andrew Smith [Mon, 21 Aug 2023 08:48:45 +0000 (09:48 +0100)]
qualcommax: ipq807x support Netgear Orbi Pro SXK80
This commit adds support for Netgear Orbi Pro SXR80 and SXS80 (collectively known as SXK80)
Specifications:
---------------
* CPU: Qualcomm IPQ8074A Quad core Cortex-A53
* RAM: 1024MB
* Storage: SPI-NAND 512 MiB (Winbond W29N04GZ)
* Ethernet: 4x 1G RJ45 ports (QCA8075) 1x 2.5G RJ45 LAN/WAN (QCA8081)
* WLAN:
- 2.4 GHz: Qualcomm QCN5024 4x4
- 2x 5 GHz: Qualcomm QCN5054 4x4 (second radio high channels only)
* LEDs:
- Power: (Green and red)
- Front: (Blue, green, red and white)
* Buttons:
- 1x Soft reset
- 1x Sync/WPS
* Power: 12V DC Jack
Installation instructions (Telnet):
-----------------------------------
*Note, this guide assumes SXR80, for SXS80 change the firmware file name as appropriate
1. Put firmware file openwrt-qualcommax-ipq807x-netgear_sxr80-initramfs-uImage.itb in root of TFTP server available at 192.168.1.10.
2. Enable telnet by going to http://[ip of device]/debug.htm and clicking on the tickbox 'Enable telnet'
3. Telnet into the device and login using the same username and password as the web interface:
4. Run the following command:
`fw_setenv bootcmd 'env default -a; saveenv; reset'`
5. Reboot the router, once the web interface is available again re-enable telnet via http://[ip of device]/debug.htm and telnet into the device.
6. Run the following command:
`fw_printenv`
It should look similar to the below:
```
baudrate=115200
bootargs=console=ttyMSM0,115200n8
bootcmd=mii write 0x0 0x0 0x800; sleep 1; nmrp; bootdni; boot_DNI_secureboot
bootdelay=2
ipaddr=192.168.1.1
netmask=255.255.255.0
serverip=192.168.1.10
soc_version_major=2
soc_version_minor=0
```
**If you see the message:**
`Warning: Bad CRC, using default environment`
**DO NOT CONTINUE, YOU WILL BRICK YOUR DEVICE**
7. Run the following command:
`fw_setenv originalboot 'mii write 0x0 0x0 0x800; sleep 1; nmrp; bootdni; boot_DNI_secureboot'`
(This should match what's in the bootcmd variable displayed in step 6)
8. Run the following commands:
```
fw_setenv wrttftp 'mii write 0x0 0x0 0x800; sleep 1; nmrp; if tftpboot openwrt-qualcommax-ipq807x-netgear_sxr80-initramfs-uImage.itb; then bootm; fi; bootdni; boot_DNI_secureboot'
fw_setenv wrtboot 'mii write 0x0 0x0 0x800; sleep 1; nmrp; nand read 0x40000000 0x1980000 0x06d00000; bootm 0x40000000'
fw_setenv bootcmd 'run wrttftp'
```
9. Ensure SXR/S device is attached via ethernet (LAN port) to the same ethernet segment as the TFTP server.
10. Reboot the device, it should reboot into OpenWrt and be available on 192.168.1.1
11. Once OpenWrt has booted, update the bootcmd using the following command:
`fw_setenv bootcmd 'run wrtboot'`
12. Flash the sysupgrade image
13. It should boot into OpenWrt
References to SXK80 GPL source:
https://www.downloads.netgear.com/files/GPL/SXK80-V3.2.0.108_gpl_src.tar.bz2.zip
Signed-off-by: Flole Systems <flole@flole.de>
Signed-off-by: Andrew Smith <gul.code@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/14939
Signed-off-by: Robert Marko <robimarko@gmail.com>
Christian Marangi [Wed, 22 May 2024 09:56:45 +0000 (11:56 +0200)]
tools/padjffs2: use Host/Prepare/Default instead of raw commands
Now that Host/Prepare/Default is always defined, we can use that instead
of using raw commands to move files from the src directory to
HOST_BUILD_DIR.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Christian Marangi [Wed, 22 May 2024 09:53:52 +0000 (11:53 +0200)]
tools/missing-macros: install files from HOST_BUILD_DIR instead of src
Install files from HOST_BUILD_DIR instead of src. These files are now
correctly copied to HOST_BUILD_DIR and can be referenced from there.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Christian Marangi [Wed, 22 May 2024 09:38:49 +0000 (11:38 +0200)]
host-build: always define Host/Prepare/Default
We currently skip defining Host/Prepare/Default if HOST_UNPACK is not
defined.
This is mostly the case for Host packages that just provide files with
the src directory and don't need to be downloaded/extracted.
This was probably done lots of times ago due to quilt causing error as
the patches directory wasn't present.
This has changed now and quilt can correctly detect if no patches needs
to be applied (instead of terminating with error)
Always define Host/Prepare/Default to make tools/refresh correctly works
as HOST_QUILT is hardcoded enabled for this make target and will
complain for tool not prepared for quilt patches.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Marius Dinu [Tue, 21 May 2024 15:08:33 +0000 (18:08 +0300)]
scripts: fix revision calculation using new "main" branch
Fix revision calculation when local branch is rebased on new "main" branch
instead of "master".
Signed-off-by: Marius Dinu <m95d+git@psihoexpert.ro>
Link: https://github.com/openwrt/openwrt/pull/15538
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Robert Marko [Tue, 21 May 2024 17:24:06 +0000 (19:24 +0200)]
qualcommax: ipq807x: sax1v1k: fix QCA8081 reset
It seems that on Spectrum SAX1V1K QCA8081 is being brought out of reset
too quickly and thus causing it to get stuck in an invalid autoneg
register configuration mode.
Setting an deasset delay seems to fix this, so lets set it.
Fixes: #15493
Link: https://github.com/openwrt/openwrt/pull/15541
Signed-off-by: Robert Marko <robimarko@gmail.com>
Robert Marko [Tue, 21 May 2024 09:28:07 +0000 (11:28 +0200)]
kernel: qca-nss-dp: add back printing attached PHY-s
During the last update to 12.5.r2 printing of the attached PHY-s was
removed, so lets bring it back as it is very helpfull for debugging
OpenWrt issues without users having to modify NSS-DP to know if a PHY
was attached.
Refresh patches since nss_dp_main.c was edited.
Link: https://github.com/openwrt/openwrt/pull/15537
Signed-off-by: Robert Marko <robimarko@gmail.com>
John Crispin [Thu, 4 Apr 2024 20:38:50 +0000 (22:38 +0200)]
mediatek/filogic: add OpenWrt One support
Specification:
- MT7981 CPU using 2.4GHz and 5GHz WiFi (both AX)
- 1GB RAM
- 16MB NOR
- 128MB NAND
- 3 LEDs (red, green, blue, white)
- 2 buttons (reset, user defined)
- 1 2.5Gbit WAN port (Airoha EN8811h)
- 1 1Gbit LAN ports
- 1 single lane M.2 SSD slot
- 1 mikroBus socket
- externel HW WDT (25s refresh time)
- i2c RTC (with battery backup)
Serial Interface
- UBS-C CDC-ACM
- 3 Pins GND, RX, TX
- Settings: 115200, 8N1
MAC addresses are not populated on the early samples.
Signed-off-by: John Crispin <john@phrozen.org>
John Crispin [Tue, 21 May 2024 09:35:05 +0000 (11:35 +0200)]
Revert "mediatek/filogic: add OpenWrt One support"
This reverts commit
797904b3cb4a5c575641c19e7f3989926e4c7902.
There is a stray line in the commit description
Signed-off-by: John Crispin <john@phrozen.org>
John Crispin [Thu, 4 Apr 2024 20:38:50 +0000 (22:38 +0200)]
mediatek/filogic: add OpenWrt One support
filogic: Add support for D-Link AQUILA PRO AI M30
Specification:
- MT7981 CPU using 2.4GHz and 5GHz WiFi (both AX)
- 1GB RAM
- 16MB NOR
- 128MB NAND
- 3 LEDs (red, green, blue, white)
- 2 buttons (reset, user defined)
- 1 2.5Gbit WAN port (Airoha EN8811h)
- 1 1Gbit LAN ports
- 1 single lane M.2 SSD slot
- 1 mikroBus socket
- externel HW WDT (25s refresh time)
- i2c RTC (with battery backup)
Serial Interface
- UBS-C CDC-ACM
- 3 Pins GND, RX, TX
- Settings: 115200, 8N1
MAC addresses are not populated on the early samples.
Signed-off-by: John Crispin <john@phrozen.org>
John Crispin [Sat, 6 Apr 2024 10:14:47 +0000 (12:14 +0200)]
uboot-mediatek: add support for OpenWrt One
Signed-off-by: John Crispin <john@phrozen.org>
John Crispin [Sat, 6 Apr 2024 17:17:05 +0000 (19:17 +0200)]
uboot-mediatek: add USB support to mt7981.dtsi
Signed-off-by: John Crispin <john@phrozen.org>
John Crispin [Thu, 4 Apr 2024 20:37:25 +0000 (22:37 +0200)]
mediatek/filogic: enable led PWM driver by default
Signed-off-by: John Crispin <john@phrozen.org>
John Crispin [Thu, 4 Apr 2024 18:11:54 +0000 (20:11 +0200)]
mediatek/filogic: fix mt7981.dtsi PCIe support
* the compatible string was wrong
* the pinmux was missing
Signed-off-by: John Crispin <john@phrozen.org>
John Crispin [Mon, 13 May 2024 05:36:24 +0000 (07:36 +0200)]
arm-trusted-firmware-mediatek: add mt7981-nor-ddr4 and mt7981-spim-nand-ubi-ddr4 builds
Signed-off-by: John Crispin <john@phrozen.org>
Felix Fietkau [Tue, 21 May 2024 08:10:00 +0000 (10:10 +0200)]
mt76: install mt7981_eeprom_mt7976_dbdc.bin to STAGING_DIR_IMAGE
It will be used in the image building code
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Felix Fietkau [Tue, 21 May 2024 08:09:12 +0000 (10:09 +0200)]
mt76: update to Git HEAD (2024-05-17)
8f301a5c5fe3 firmware: add mt7981 default eeprom
2d264aecbf5a mt76: mt7915: make pre-cal freq lists static const
d9c62742bed6 wifi: mt76: make const arrays in functions static
8986ba5492a8 wifi: mt76: mt7921: cqm rssi low/high event notify
3afbb8ed8015 wifi: mt76: mt7996: let upper layer handle MGMT frame protection
1d0bd57e5889 wifi: mt76: mt7921e: add LED control support
1d6e4f7de8a6 wifi: mt76: mt7925: add EHT radiotap support in monitor mode
c40e648b8929 wifi: mt76: enable spectrum management
14d5ee9f3369 mt76: shrink mt76_queue_buf
513c131c6309 mt76: mt7603: fix mixed declarations and code
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Jo-Philipp Wich [Tue, 21 May 2024 06:59:13 +0000 (08:59 +0200)]
firewall4: update to Git HEAD (2024-05-21)
4c01d1ebf99e fw4: substitute double quotes in strings
Fixes: https://github.com/openwrt/luci/issues/7091
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Tony Ambardar [Thu, 16 May 2024 21:14:05 +0000 (14:14 -0700)]
libbpf: Update to v1.4.2
Update to the latest upstream release to include recent improvements and
bugfixes.
Link: https://github.com/libbpf/libbpf/releases/tag/v1.4.2
Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
Linus Walleij [Wed, 15 May 2024 21:16:54 +0000 (23:16 +0200)]
ixp4xx: Bump to kernel v6.6
The IXP4xx is well supported upstream and can readily be
supported with kernel v6.6. To simplify things after the
DTS directory was renamed, switch to v6.6 only.
Bring in some outstanding patches.
Tested on the Gateworks GW2348-4.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Paul Spooren [Mon, 20 May 2024 15:10:42 +0000 (18:10 +0300)]
apk: update to latest HEAD 2024-05-19
Upstream refactoring caused some mbedtls issues, now fixed again.
Signed-off-by: Paul Spooren <mail@aparcar.org>
Paul Spooren [Mon, 20 May 2024 15:08:28 +0000 (18:08 +0300)]
apk: disable rootfs repositories during build
Since we set the root for APK it tries to use those during the build,
which shouldn't happen since local package are used instead.
Disable the repositories by manually setting an empty repository.
Signed-off-by: Paul Spooren <mail@aparcar.org>
Rui Salvaterra [Wed, 8 May 2024 21:04:55 +0000 (22:04 +0100)]
linux-firmware: realtek: update rtl8821ae firmware
A newer version, rtl8821aefw_29.bin, has been available for over 7 years [1].
Let's use it.
[1] https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/commit?id=
f70e4df2b384d21e36a7c30a591639592692e0ec
Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
Linus Walleij [Wed, 15 May 2024 08:21:47 +0000 (10:21 +0200)]
gemini: In-flight ethernet patches
These patches have partial acceptance upstream and are still
a WIP, now there is merge window for kernel v6.10 so these
will not be reposted until that is over. In the meantime,
let's add the current state to OpenWrt so the ethernet on
Gemini is up and working (tested on several devices).
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Christian Marangi [Sun, 19 May 2024 13:03:27 +0000 (15:03 +0200)]
include/rootfs: skip removal of APK cache now deprecated
Skip removal of APK cache since now deprecated as APK doesn't make use
of cache anymore in our configuration.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Christian Marangi [Sun, 19 May 2024 12:58:11 +0000 (14:58 +0200)]
imagebuilder: fix multiple issue with manifest and sign keys handling
Fix multiple issue with manifest handling where APK was hardcoded
and fix a logic error where (TODO) APK _check_keys was called for the
OPKG codepath instead of correctly calling for the APK codepath.
Fixes: d788ab376f85 ("build: add APK package build capabilities")
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Yuu Toriyama [Sat, 18 May 2024 22:08:37 +0000 (07:08 +0900)]
wireless-regdb: update to 2024.05.08
Changes:
73529a8 Revert "wireless-regdb: Update and disable 5470-5730MHz band according to TPC requirement for Singapore (SG)"
87941e4 wireless-regdb: Update regulatory rules for Taiwan (TW) on 6GHz
33797ae wireless-regdb: update regulatory database based on preceding changes
Signed-off-by: Yuu Toriyama <PascalCoffeeLake@gmail.com>
Felix Fietkau [Fri, 10 May 2024 15:39:56 +0000 (17:39 +0200)]
mediatek: add firmware name for AQR PHYs on mt7988a-rfb
Fixes PHY probe in case there is no firmware in a connected EEPROM
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Felix Fietkau [Wed, 8 May 2024 11:40:14 +0000 (13:40 +0200)]
mediatek: convert mt7988a-rfb to keep bl31/uboot in UBI
Add ubi volumes for mt7988a-rfb and support for using factory data
for Ethernet MAC addresses and MT7996 WLAN calibration data.
Also add rootdisk handle. Removes the need to keep using nmbm
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Felix Fietkau [Mon, 13 May 2024 18:17:33 +0000 (20:17 +0200)]
uboot-mediatek: add missing options for mt7988-rfb
Fixes autoboot and storing env in UBI
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Paul Spooren [Sat, 18 May 2024 20:10:49 +0000 (23:10 +0300)]
rootfs: fix USE_APK detection
Due to missing quotes the script would wrongly assume APK to be enabled
and don't run post install scripts, breaking pretty much everything.
Signed-off-by: Paul Spooren <mail@aparcar.org>
Paul Spooren [Sat, 18 May 2024 13:29:07 +0000 (16:29 +0300)]
apk: update to latest HEAD 2024-05-18
Drop downstream mbedtls patch since it went upstream.
Signed-off-by: Paul Spooren <mail@aparcar.org>
Link: https://github.com/openwrt/openwrt/pull/15522
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Paul Spooren [Fri, 17 May 2024 20:32:00 +0000 (23:32 +0300)]
base-files: correctly split install-key function for APK
The function incorrectly tried to APK keys even if there were none.
Correctly separate it into its own `ifdef` section.
Signed-off-by: Paul Spooren <mail@aparcar.org>
Link: https://github.com/openwrt/openwrt/pull/15519
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Paul Spooren [Fri, 17 May 2024 20:19:52 +0000 (23:19 +0300)]
apk: disable helptext for host build
The host build would need Lua to compile which currently adds a race
condition. Instead of tracking that down just disable helptext for the
host build.
Signed-off-by: Paul Spooren <mail@aparcar.org>
Paul Spooren [Fri, 3 May 2024 16:24:17 +0000 (18:24 +0200)]
base-files: add compatibility for APK and OPKG
Both package managers work slightly different, i.e. stores files at
different places. Modify the `functions.sh` file to cover those.
Signed-off-by: Paul Spooren <mail@aparcar.org>
Paul Spooren [Fri, 3 May 2024 15:53:52 +0000 (17:53 +0200)]
base-files: add update_alternatives function
The APK package manager does not support handling of package
alternatives itself, so implement it via a simple shell script.
Signed-off-by: Paul Spooren <mail@aparcar.org>
Paul Spooren [Tue, 14 May 2024 10:36:59 +0000 (12:36 +0200)]
build: add APK package build capabilities
A new option called `USE_APK` is added which generated APK packages
(.apk) instead of OPKG packages (.ipk).
Some features like fstools `snapshot` command are not yet ported
Signed-off-by: Paul Spooren <mail@aparcar.org>
Paul Spooren [Fri, 3 May 2024 15:26:35 +0000 (17:26 +0200)]
gitignore: ignore local APK keys
Those keys should never be added to the git repository.
Signed-off-by: Paul Spooren <mail@aparcar.org>
Paul Spooren [Fri, 17 May 2024 18:47:46 +0000 (21:47 +0300)]
apk: add missing PROVIDES
Add PROVIDES:=apk to the Makefile so we can default to install `apk` by
default as a dependency.
Signed-off-by: Paul Spooren <mail@aparcar.org>
Paul Spooren [Fri, 3 May 2024 15:43:08 +0000 (17:43 +0200)]
rpcd: fix package dependency for APK
Version dependencies must not contain spaces to be compatible with both
OPKG and APK.
Signed-off-by: Paul Spooren <mail@aparcar.org>
Tomasz Maciej Nowak [Wed, 15 May 2024 17:11:53 +0000 (19:11 +0200)]
uboot-tegra: bump version to 2024.04
Since swig is mentioned as build dependency and buildbots have it
installed we can safely bump version.
Signed-off-by: Tomasz Maciej Nowak <tmn505@gmail.com>
Tomasz Maciej Nowak [Wed, 15 May 2024 17:02:09 +0000 (19:02 +0200)]
tegra: trimslice: enable USB HID driver
Without serial or network access the only option for initial
configuration, is a attached display with USB keyboard, but the keyboard
driver needs to be installed first. So enable keyboard driver by default
to avoid this issue.
Signed-off-by: Tomasz Maciej Nowak <tmn505@gmail.com>
Tomasz Maciej Nowak [Wed, 15 May 2024 17:02:08 +0000 (19:02 +0200)]
tegra: trimslice: enable GPIO LEDs driver
LEDs are on all the time since boot, until there's driver to claim them.
Signed-off-by: Tomasz Maciej Nowak <tmn505@gmail.com>
Tomasz Maciej Nowak [Wed, 15 May 2024 17:02:07 +0000 (19:02 +0200)]
tegra: drop console specifiers from kernel commad line
Because recent changes to procd, last "console" argument was used as
primary argument and causing no terminal to be spawned on serial
interface. So drop the hardcoded consoles in boot script, since dts has
already an alias specified, which lets procd decide where to spawn the
terminal.
Signed-off-by: Tomasz Maciej Nowak <tmn505@gmail.com>
Tomasz Maciej Nowak [Wed, 15 May 2024 17:02:06 +0000 (19:02 +0200)]
tegra: pad rootfs to recreate overlay after upgrade
The old overlay remained after upgrades and would cause failure on first
boot after upgrade, in which no new overlay could be created while old
one was unusable.
Signed-off-by: Tomasz Maciej Nowak <tmn505@gmail.com>
Paweł Owoc [Mon, 26 Feb 2024 10:38:02 +0000 (11:38 +0100)]
qualcommax: ipq807x: add support for Linksys MX8500
Hardware specification:
========
SoC: Qualcomm IPQ8072A
Flash: 512MB (Fidelix FMND4G08S3J-ID)
RAM: 1GB (2x Kingston DDR3L D2516ECMDXGJD)
Ethernet: 1x 10/100/1000/2500/5000Mbps (Marvell AQR114C)
Ethernet: 4x 10/100/1000Mbps (Qualcomm QCA8075)
WiFi1: 6GHz ax 4x4 (Qualcomm QCN9024 + Skyworks SKY85784-11) - channels 33-229
WiFi2: 5GHz ax 4x4 (Qualcomm QCN5054 + Skyworks SKY85755-11) - channels 36-177
WiFi3: 2.4GHz ax 4x4 (Qualcomm QCN5024 + Skyworks SKY8340-11)
IoT: Bluetooth 5, Zigbee and Thread (NXP K32W041)
LED: 1x RGB status (NXP PCA9633)
USB: 1x USB 3.0
Button: WPS, Reset
Flash instructions:
========
1. Manually upgrade firmware using openwrt-qualcommax-ipq807x-linksys_mx8500-squashfs-factory.bin image.
More details can be found here: https://www.linksys.com/support-article?articleNum=47547
After first boot check actual partition:
- fw_printenv -n boot_part
and install firmware on second partition using command in case of 2:
- mtd -r -e kernel -n write openwrt-qualcommax-ipq807x-linksys_mx8500-squashfs-factory.bin kernel
and in case of 1:
- mtd -r -e alt_kernel -n write openwrt-qualcommax-ipq807x-linksys_mx8500-squashfs-factory.bin alt_kernel
2. Installation using serial connection from OEM firmware (default login: root, password: admin):
- fw_printenv -n boot_part
In case of 2:
- flash_erase /dev/mtd21 0 0
- nandwrite -p /dev/mtd21 openwrt-qualcommax-ipq807x-linksys_mx8500-squashfs-factory.bin
or in case of 1:
- flash_erase /dev/mtd23 0 0
- nandwrite -p /dev/mtd23 openwrt-qualcommax-ipq807x-linksys_mx8500-squashfs-factory.bin
After first boot install firmware on second partition:
- mtd -r -e kernel -n write openwrt-qualcommax-ipq807x-linksys_mx8500-squashfs-factory.bin kernel
or:
- mtd -r -e alt_kernel -n write openwrt-qualcommax-ipq807x-linksys_mx8500-squashfs-factory.bin alt_kernel
3. Installation from initramfs image using USB drive:
Put the initramfs image on the USB drive:
- dd bs=1M if=openwrt-qualcommax-ipq807x-linksys_mx8500-initramfs-uImage.itb of=/dev/sda
Stop u-boot and run:
- usb start && usbboot $loadaddr 0 && bootm $loadaddr
Write firmware to the flash from initramfs:
- mtd -e kernel -n write openwrt-qualcommax-ipq807x-linksys_mx8500-squashfs-factory.bin kernel
and:
- mtd -r -e alt_kernel -n write openwrt-qualcommax-ipq807x-linksys_mx8500-squashfs-factory.bin alt_kernel
4. Back to the OEM firmware:
- mtd -e kernel -n write FW_MX8500_1.0.11.208937_prod.img kernel
and:
- mtd -r -e alt_kernel -n write FW_MX8500_1.0.11.208937_prod.img alt_kernel
5. USB recovery:
Put the initramfs image on the USB:
- dd bs=1M if=openwrt-qualcommax-ipq807x-linksys_mx8500-initramfs-uImage.itb of=/dev/sda
Set u-boot env:
- fw_setenv bootusb 'usb start && usbboot $loadaddr 0 && bootm $loadaddr'
- fw_setenv bootcmd 'run bootusb; if test $auto_recovery = no; then bootipq; elif test $boot_part = 1; then run bootpart1; else run bootpart2; fi'
AQR firmware:
========
1. Firmware loading:
To properly load the firmware and initialize AQR PHY, we must use the u-boot aq_load_fw function.
To do this, you need to modify u-boot env:
With USB recovery:
- fw_setenv bootcmd 'aq_load_fw; run bootusb; if test $auto_recovery = no; then bootipq; elif test $boot_part = 1; then run bootpart1; else run bootpart2; fi'
and without:
- fw_setenv bootcmd 'aq_load_fw; if test $auto_recovery = no; then bootipq; elif test $boot_part = 1; then run bootpart1; else run bootpart2; fi'
2. Firmware updating:
Newer firmware (AQR-G4_v5.6.5-AQR_WNC_SAQA-L2_GT_ID45287_VER24005.cld) is available in the latest OEM firmware.
To load this firmware via u-boot, we need to add the MBN header and update 0:ethphyfw partition.
For MBN header we can use script from this repository: https://github.com/testuser7/aqr_mbn_tool
- python aqr_mbn_tool.py AQR-G4_v5.6.5-AQR_WNC_SAQA-L2_GT_ID45287_VER24005.cld
To update partition we need to install kmod-mtd-rw package first:
- insmod mtd-rw.ko i_want_a_brick=1
- mtd -e /dev/mtd26 -n write aqr_fw.mbn /dev/mtd26
Signed-off-by: Paweł Owoc <frut3k7@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/14883
Signed-off-by: Robert Marko <robimarko@gmail.com>
Paweł Owoc [Wed, 13 Mar 2024 11:36:39 +0000 (12:36 +0100)]
qualcommax: ipq807x: define common Linksys MX device
Define common Linksys MX device for MX4200v1/v2 and MX5300.
Signed-off-by: Paweł Owoc <frut3k7@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/14883
Signed-off-by: Robert Marko <robimarko@gmail.com>
Paweł Owoc [Wed, 13 Mar 2024 12:01:01 +0000 (13:01 +0100)]
qca-ssdk: add patch to support AQR114C-B0 PHY
Add support for AQR114C-B0 PHY.
Signed-off-by: Paweł Owoc <frut3k7@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/14883
Signed-off-by: Robert Marko <robimarko@gmail.com>
Paweł Owoc [Wed, 13 Mar 2024 11:57:04 +0000 (12:57 +0100)]
generic: 6.6: add patch to support AQR114C PHY ID
Add support for AQR114C PHY ID.
Signed-off-by: Paweł Owoc <frut3k7@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/14883
Signed-off-by: Robert Marko <robimarko@gmail.com>
Paweł Owoc [Wed, 13 Mar 2024 11:22:30 +0000 (12:22 +0100)]
qualcommax: ipq807x: Remove unused gpio from QPIC pins
Remove gpio16 from the default NAND pinctrl configuration
as its unused and only needed for LCD.
Signed-off-by: Paweł Owoc <frut3k7@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/14883
Signed-off-by: Robert Marko <robimarko@gmail.com>
Robert Marko [Thu, 16 May 2024 10:03:19 +0000 (12:03 +0200)]
ipq806x: mr42/mr52: fix PCIe ports
All three PCIe ports are reported non working on Meraki MR42/MR52 boards
since kernel 6.1 with the issue of PCIe PHY link never coming up thus
no WLAN cards are available on the boards.
After debugging it seems that PCIe worked on 5.15 and older purely by
accident as device DTS was using /delete-property/ perst-gpios; in each
of the 3 PCIe nodes but there was no "perst-gpios" property in the SoC DTSI
as it was still using the older "perst-gpio" property so it was not getting
removed from the device DTS.
However, in kernel 6.1 commit ("ARM: dts: qcom-*: replace deprecated
perst-gpio with perst-gpios") updated all Qualcomm DTS-es to use the newer
"perst-gpios" and thus once ipq806x moved to 6.1 PCIe stopped working as
now that property was being dropped from the device DTS.
So, since the removal of PERST pins seems to have been wrong from the start
lets drop the property removal from MR42/MR52.
Fixes: #15408
Link: https://github.com/openwrt/openwrt/pull/15509
Signed-off-by: Robert Marko <robimarko@gmail.com>
Robert Marko [Wed, 15 May 2024 08:57:06 +0000 (10:57 +0200)]
generic: 6.6: remove kernel export stripping patch
Our kernel export stripping has been broken on 6.6 from the start since
upstream kernel really reworked stuff in ("kbuild: generate KSYMTAB entries
by modpost") and other commits as well.
So, until this is either fixed or reworked lets drop the patch as it doesnt
make sense to carry it knowing its broken and it can always be easily
restored.
Link: https://github.com/openwrt/openwrt/pull/15498
Signed-off-by: Robert Marko <robimarko@gmail.com>
Robert Marko [Wed, 15 May 2024 08:43:52 +0000 (10:43 +0200)]
config: build: dont allow STRIP_KERNEL_EXPORTS on kernel 6.6
STRIP_KERNEL_EXPORTS is currently not working on kernel 6.6 as there
have been major changes in the upstream kernel.
I have looked at it, and I dont think we can adapt the current patch to
work so until this is fixed lets prevent STRIP_KERNEL_EXPORTS from
being selected on 6.6.
Link: https://github.com/openwrt/openwrt/pull/15498
Signed-off-by: Robert Marko <robimarko@gmail.com>
Hauke Mehrtens [Thu, 9 May 2024 20:10:52 +0000 (22:10 +0200)]
ramips: Fix use mac-base for TP-Link TL-MR6400 v4 and v5
Use mac-base for mac-base TP-Link TL-MR6400 v4 and v5
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Hauke Mehrtens [Thu, 9 May 2024 10:28:35 +0000 (12:28 +0200)]
ramips: Fix wmac dts definition for TP-Link TL-MR6400 v4 and v5
This code assumed that the mt7628an_tplink_8m.dtsi file defines
mediatek,mtd-eeprom for the wmac and sets status to okay.
The mediatek,mtd-eeprom definition was removed in commit
e93f41adee3e
("ramips: convert MT7628 EEPROM to NVMEM format") but the dts for these
two devices was not adapted to include the eeprom position on its own.
The status = "okay" property was removed in
0a1d15642fa6 ("ramips:
mt7628: use nvmem-layout"), but the property was not added to these dts
files.
Without this change wifi does not work for these devices.
Fixes: e93f41adee3e ("ramips: convert MT7628 EEPROM to NVMEM format")
Fixes: 0a1d15642fa6 ("ramips: mt7628: use nvmem-layout")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
David Adriao [Fri, 10 May 2024 20:10:48 +0000 (21:10 +0100)]
mac80211: Add support for RTL8723BE
This adds support for the RTL8723BE PCIe Wi-Fi Adapter by adding backports drivers
Signed-off-by: David Adriao <davidadriao@dglitch.com>
[Do not remove rtl8xxxu and add dependency to rtl8723be-firmware]
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Martin Schiller [Mon, 6 May 2024 09:01:15 +0000 (11:01 +0200)]
lantiq: add patch to fix the reset gpio handling in the pci driver
Linux kernel commit
90c2d2eb7ab5 ("MIPS: pci: lantiq: switch to using
gpiod API") not only switched to the gpiod API, but also inverted /
changed the polarity of the GPIO.
According to the PCI specification, the RST# pin is an active-low
signal. However, most of the device trees that have been widely used for
a long time (mainly in the openWrt project) define this GPIO as
active-high and the old driver code inverted the signal internally.
Apparently there are actually boards where the reset gpio must be
operated inverted. For this reason, we cannot use the GPIOD_OUT_LOW/HIGH
flag for initialization. Instead, we must explicitly set the gpio to
value 1 in order to take into account any "GPIO_ACTIVE_LOW" flag that
may have been set.
In order to remain compatible with all these existing device trees, we
should therefore keep the logic as it was before the commit.
Signed-off-by: Martin Schiller <ms@dev.tdt.de>
Martin Schiller [Tue, 16 Apr 2024 06:45:17 +0000 (08:45 +0200)]
lantiq: ltq-adsl-mei: use platform_get_irq to get irqs
This is required for linux-6.1 compatibility.
IRQs are not automatically mapped from HW to virtual IRQ numbers when
the IRQ domain is registered. This happens when the IRQ number is read
from the device tree based on the IRQ domain from the device tree now.
In kernel 5.15 it was done when the IRQ domain was registered.
Signed-off-by: Martin Schiller <ms@dev.tdt.de>
Martin Schiller [Tue, 16 Apr 2024 06:43:30 +0000 (08:43 +0200)]
lantiq: dts: add missing irqs to mei node on AmazonSE, Danube and AR9
This adds to missing DyingGasp and USB OC interrupts to the mei node.
Signed-off-by: Martin Schiller <ms@dev.tdt.de>
Martin Schiller [Mon, 15 Apr 2024 14:54:59 +0000 (16:54 +0200)]
lantiq: ltq-vmmc: get irqs from kernel-in-tree vmmc driver
Let's get the IRQs from the kernel-in-tree vmmc driver like it is
already done for the cp1 base addr.
Signed-off-by: Martin Schiller <ms@dev.tdt.de>
Martin Schiller [Mon, 15 Apr 2024 14:54:07 +0000 (16:54 +0200)]
lantiq: vmmc kernel-in-tree driver: use platform_get_irq to get irqs
This is required for linux-6.1 compatibility.
IRQs are not automatically mapped from HW to virtual IRQ numbers when
the IRQ domain is registered. This happens when the IRQ number is read
from the device tree based on the IRQ domain from the device tree now.
In kernel 5.15 it was done when the IRQ domain was registered.
Signed-off-by: Martin Schiller <ms@dev.tdt.de>
Martin Schiller [Fri, 12 Apr 2024 13:14:57 +0000 (15:14 +0200)]
lantiq: ltq-vmmc: fix write beyond size of field
This fixes the write beyond size of field compile warning/error.
Signed-off-by: Martin Schiller <ms@dev.tdt.de>
Martin Schiller [Fri, 12 Apr 2024 08:37:58 +0000 (10:37 +0200)]
lantiq: ltq-atm: use platform_get_irq to get irqs
This is required for linux-6.1 compatibility.
IRQs are not automatically mapped from HW to virtual IRQ numbers when
the IRQ domain is registered. This happens when the IRQ number is read
from the device tree based on the IRQ domain from the device tree now.
In kernel 5.15 it was done when the IRQ domain was registered.
Signed-off-by: Martin Schiller <ms@dev.tdt.de>
projects / openwrt / staging / jow.git / log