git.openwrt.org Git - openwrt/openwrt.git/log

ramips: mt7621: add support for Confiabits MT7621 v1

Hardware:
- SoC: MediaTek MT7621DAT
- Flash: 16 MiB cFeon
- RAM: 128 MiB MT7621DAT
- WLAN: 2.4 GHz (MT7603EN), 5 GHz (MT7613BEN 802.11ac)
- Ethernet: 1x 10/100/1000 Mbps WAN, 3x 10/100/1000 LAN (MT7621DAT)
- Buttons: 1 Reset button, 1 WPS button
- LEDs: 5x Green (POWER/WAN/2.4G/5G/WPS), 1x Red (WAN)
- Serial console: unpopulated header, 57600 8n1
- Power: 12 VDC, 1 A

MAC:
LAN MAC: label mac (eeprom@4)
WAN MAC: label mac (eeprom@4)
2.4G MAC: label mac (eeprom@4)
5G MAC: label mac + 1 (eeprom@8004)

Installation:
The stock firmware is OpenWrt-based. If you can reach LuCI or SSH, just use the sysupgrade image
with the 'Keep settings' option turned off.

Signed-off-by: Luis Mita <luis@luismita.com>
Link: https://github.com/openwrt/openwrt/pull/17534
(cherry picked from commit 1c5ca24da6cd727f4fcb8edbe00fa66543a6c678)
Link: https://github.com/openwrt/openwrt/pull/17653
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>

qualcommax: dl-wrx36: fix 2.5G port LED-s

Currently, 2.5G port LED-s on Dynalink are incorrectly configured and thus
they will light up all of the time.

So, lets fix this by:
1. Current green LED is actually yellow, change the color
2. Fix its polarity as its actually active-low
3. The yellow LED that was registered as being connected to LED_1 pin on
the PHY is not actually connected at all, so remove it.
4. The actual green LED is connected to LED_2 on the PHY so add it.

Fixes: 75ad5c24142a ("qualcommax: switch to qca8081 upstream PHY driver")
Fixes: #14502
Link: https://github.com/openwrt/openwrt/pull/17656
Signed-off-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit 2d077913cd53cad33123c8a9bf6da8a1c5576c69)

generic: backport pending Realtek PHY patches

These patches have been accepted, so we can move them from pending to
backported.

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
(cherry picked from commit 7924acdd63490aa436bf114d290cb56cd4eba008)

generic: add pending patches for RealTek Ethernet PHYs

Import patches to fix several issues with status reporting of RealTek
2.5G PHYs.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
(cherry picked from commit 41c164d32bedb6b27ad1fd022dec6d25338db6d6)

generic: backport Realtek PHY patches from upstream

Adds patches for the temperature sensor on RTL822x.

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
(cherry picked from commit d7e82c78d7a2a84404198dab8faf8e142939eb05)

generic: r8169: remove reverted temperature sensor patch

The patch adding temperature sensor support for r8169 has been removed upstream
and the functionality will be added to Realtek PHY instead:
https://github.com/torvalds/linux/commit/1f691a1fc4bef1c5cf5f503e14e1a22fc37c97e3

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
(cherry picked from commit 0de9999a7819acf74f6adeaa27be363cf72409ab)

airoha: an7581: add pending PCI patch

Add pending PCI patch that should correctly fix mediatek driver with
Airoha SoC.

Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
(cherry picked from commit f22febae1a6b7c654eaf09ed02c0d0017be6d73a)

airoha: an7581: backport ETS patch for Airoha ethernet

Backport ETS patch for Airoha ethernet and refresh affected patches.

Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
(cherry picked from commit 67635578fd19d0576c54bbe722a9664e8a6ab2a6)

uci: update to Git HEAD (2025-01-17)

fb3c2343b17b add support for an override config directory

Signed-off-by: Felix Fietkau <nbd@nbd.name>
(cherry picked from commit 44c877f1973b923a2032ce9d880f496a2b077ef6)

uci: update to Git HEAD (2024-11-26)

10f7996ec294 file: Ignore config file with '.' in name

Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
(cherry picked from commit 3929ef4c21844189d5db8d14e7e6dc6ba983d571)

mediatek: remove obsolete base-files scripts

Signed-off-by: Felix Fietkau <nbd@nbd.name>
(cherry picked from commit 48e1427ffa867bddc822a463af862b9dacc5bde8)

netifd: improve packet steering on ipq40xx (and possibly others)

Some platforms a single ethernet device for all ports with multiple rx rings
and NAPI threading enabled. In this case, the steering script was limiting
performance by keeping all NAPI threads assigned to the same CPU.
Fix this by assigning each rx queue and the corresponding NAPI task separately.
Additionally, if the number of rx queues is at least as big as the number of
CPUs, skip weight based assignment and distribute the load across all CPUs
directly.

Fixes: https://github.com/openwrt/openwrt/issues/17611
Signed-off-by: Felix Fietkau <nbd@nbd.name>
(cherry picked from commit acce25b789d40f2d88a2326a7d9921bd1743fe54)

mvebu: WD Cloud Mirror Gen2: Remove stty dependency

The package coreutils-stty is not part of the OpenWrt main packages. A
board can not depend on it. Remove the dependency to fix a build problem
seen in the build bots.

Fixes: 8fb805aa1f25 ("mvebu: Add support for WD Cloud Mirror Gen2")
(cherry picked from commit 717f62d256ccb52549a24c256615b28440ed1a86)
Link: https://github.com/openwrt/openwrt/pull/17589
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>

mvebu: Add support for WD Cloud Mirror Gen2

Hardware
--------
Marvell Armada 385 (MV88F6820)
512B RAM
256MB NAND (Hynix H27U2G8F2CTR)
1x 1Gbit
2x USB 3.0
2x SATA-III
UART: 115200 8N1 3.3V
RTC
Weltrend MCU WT6703F connected via UART1 for Power LED / PWM Fan / hw reset / WoL

Installation
------------
Connect UART 3.3V adapter to JP2 pins: 1-RX / 2-GND / 5-TX

Use USB2.0 FAT32 pendrive with openwrt-mvebu-cortexa9-wd_cloud-mirror-gen2-initramfs-kernel.bin
1. stop boot by pressing 1
2. usb start
3. fatload usb 0:1 0x02000000 openwrt-mvebu-cortexa9-wd_cloud-mirror-gen2-initramfs-kernel.bin;bootm 0x02000000 -
4. do backup mtd1 mtd3
5. use sysupgrade

Or tftp
1. stop boot by pressing 1
2. setenv ethact egiga2;setenv serverip 192.168.11.114;setenv ipaddr 192.168.11.113
3. tftpboot 0x02000000 openwrt-mvebu-cortexa9-wd_cloud-mirror-gen2-initramfs-kernel.bin; bootm 0x02000000 -
4. do backup mtd1 mtd3
5. use sysupgrade

or Evgeny Kolesnikov <evgenyz@gmail.com> method from his failed PR 2040

- Using original firmware's network settings obtain SSH access to the device.
- Put *-image-cfs-factory.bin and *-uImage-factory.bin images into device's /tmp directory.
- Write kernel (uImage) image 'flash_eraseall /dev/mtd1 && nandwrite --markbad -p /dev/mtd1 /tmp/*-uImage-factory.bin'.
- Write rootfs (image-cfs) image 'ubiformat /dev/mtd3 -f /tmp/*-image.cfs-factory.bin -y'.
- Reboot the device.

Installation (upgrade):

Use *-sysupgrade.bin in a usual way.
Weltrend MCU control is done via uart1 19200

stty -F /dev/ttyS1 raw speed 19200
stty -F /dev/ttyS1 raw speed 19200

PWM Fan Control
off: 00
echo -n -e '\xfa\x02\x00\x00\x00\x00\xfb' > /dev/ttyS1
slow: 5F
echo -n -e '\xfa\x02\x00\x5f\x00\x00\xfb' > /dev/ttyS1
max: FF
echo -n -e '\xfa\x02\x00\xff\x00\x00\xfb' > /dev/ttyS1

Power LED Control
Blue
echo -n -e '\xfa\x26\x00\x11\x00\x01\xfb' > /dev/ttyS1
Red
echo -n -e '\xfa\x26\x00\x14\x00\x01\xfb' > /dev/ttyS1
Orange
echo -n -e '\xfa\x26\x00\x12\x00\x01\xfb' > /dev/ttyS1

more here: https://github.com/c-MM/mcm-daemon/blob/master/mcm.h

Signed-off-by: Robert Senderek <robert.senderek@10g.pl>
Link: https://github.com/openwrt/openwrt/pull/17046
(cherry picked from commit 8fb805aa1f25b69b7849c8b1ce787ed47b16d123)
Link: https://github.com/openwrt/openwrt/pull/17589
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>

armsr: change image names to 'combined-efi'

luci-app-attendedsysupgrade expects images to be named
'combined-efi' when the system is using EFI images.

This came about as x86 has 'combined' images for legacy
(BIOS) boot and 'combined-efi' for EFI systems.

armsr images were originally named 'combined' only
as there was no 'legacy' image type.

To avoid special handling in the attendedsysupgrade
code, name EFI images consistent with other targets.

Signed-off-by: Mathew McBride <matt@traverse.com.au>
Link: https://github.com/openwrt/luci/pull/6430
Link: https://github.com/openwrt/openwrt/pull/12963
Signed-off-by: Petr Štetiar <ynezz@true.cz>
(cherry picked from commit c9ebd4fb30773ca55cc2da6b2c1962046a2e0fff)

netifd: fix napi process name matching in packet steering script

Fixes CPU usage imbalance on some devices using threaded NAPI

Signed-off-by: Felix Fietkau <nbd@nbd.name>
(cherry picked from commit 67a4aeef6c63e5836bd6b82faf6cc15934869efb)

wifi-scripts: allow per-IF mesh basic rate selection

Bringing up a mesh interface using wpa_supplicant already supports a
per-VIF basic rate selection. Add the same ability when creating a mesh
VIF without wpa_supplicant.

Signed-off-by: David Bauer <mail@david-bauer.net>
(cherry picked from commit 3deeb7805f69f54b9ab20c0e12f8dd916fec4de1)

wifi-scripts: remove leftover legacy (non-netifd) wifi script support

cfg80211 is the only supported wireless API

Signed-off-by: Felix Fietkau <nbd@nbd.name>
(cherry picked from commit d1275392916522d664e710752c517246540cbf73)

wifi-scripts: add macaddr_base wifi-device option

This can be used to configure the base mac address from which all
interface mac addresses are derived

Signed-off-by: Felix Fietkau <nbd@nbd.name>
(cherry picked from commit 00860e485b2ef82c1fafc8e011f3a8965e317bca)

hostapd: fix processing mbssid config option

Do not strip the first character from the field name

Signed-off-by: Felix Fietkau <nbd@nbd.name>
(cherry picked from commit 59dd9cddf9e72d1f9b4ff7e01ae32d2fa99259d9)

wifi-scripts: add option to set per-device ifname prefix

Simplifies setting ifname to a different pattern for all affected
interfaces.

Signed-off-by: Felix Fietkau <nbd@nbd.name>
(cherry picked from commit a9ff3ba24b9466d9c06b9a9e1c2e9672bdd9f6f9)

mt76: update to Git HEAD (2025-01-14)

cf4e709e493a wifi: mt76: mt7996: fix crash in mt7996_set_radar_background
4c786fa52bb2 wifi: mt76: mt7915: fix register mapping
849923df3dde wifi: mt76: mt7996: fix register mapping
6be1dc9a1c79 wifi: mt76: mt7925: fix the unfinished command of regd_notifier before suspend
d33ea3cab72b wifi: mt76: mt7925: fix CLC command timeout when suspend/resume
5aacd0d73c80 wifi: mt76: mt7925: add handler to hif suspend/resume event
e86e97e45397 wifi: mt76: mt7925e: fix too long of wifi resume time
e43df6bf4892 wifi: mt76: mt7996: fix thermal sparse warning
02f453d8dfc8 wifi: mt76: fix survey regression
7279e3f3c3e0 wifi: mt76: mt7925: fix unused-but-set warning
49c0bd66da3b wifi: mt76: mt7996: fix unused-but-set variable
2c068c96382e wifi: mt76: fix crash in mt76_switch_vif_chanctx
731070da2c2a wifi: mt76: mt7996: add max mpdu len capability
99d8ed164a96 wifi: mt76: mt7996: fix the capability of reception of EHT MU PPDU
32ee924831ba wifi: mt76: mt7996: fix HE Phy capability
9b588c7fb333 wifi: mt76: mt7996: fix incorrect indexing of MIB FW event
46798905cf5a wifi: mt76: connac: adjust phy capabilities based on band constraints
5c50f6f7dafe wifi: mt76: mt7996: fix definition of tx descriptor
9cdb62dc084f wifi: mt76: mt7996: fix ldpc setting
8c6cb2f97fe0 wifi: mt76: mt7996: fix beacon command during disabling
8e4f72b682e9 wifi: mt76: mt7996: add implicit beamforming support for mt7992

Signed-off-by: Felix Fietkau <nbd@nbd.name>
(cherry picked from commit 3963dab0302ae29cbf2acf28f26c1432e4ddf1a5)

realtek: debounce reset key for Zyxel GS1900

When the reset button is next to the SFP cages, I2C operations on the
modules might cause interference on the button's GPIO line. Add a
debounce-interval of 5 times the poll-interval to ensure the line is
actually stable for some time and not just glitching.

This squashes commit 4357f32d41eb ("realtek: debounce reset key for
Zyxel GS1900") and commit 777c6106ed4e ("realtek: move debounce-interval
to correct node").

Signed-off-by: Sander Vanheule <sander@svanheule.net>

hostapd: backport upstream patch to fix setting BSS color

Without this patch, we get the following error:

Mon Dec 23 11:35:44 2024 daemon.err hostapd: nl80211: kernel reports: integer out of range

As updating hostapd would be too complex and requires further testing,
we backport this simple upstream fix instead.

Fixes: https://github.com/openwrt/openwrt/issues/16680
Signed-off-by: Rany Hany <rany_hany@riseup.net>
Link: https://github.com/openwrt/openwrt/pull/17590
Signed-off-by: Petr Štetiar <ynezz@true.cz>
(cherry picked from commit 5ce1af9539da667f62dc3cb426f9ec36e53fb54e)
Link: https://github.com/openwrt/openwrt/pull/17591
Signed-off-by: Robert Marko <robimarko@gmail.com>

ath79: teltonika-rut230: fix failsafe boot without SIM tray

Due to "SIM present" input defaulting to "button" type, it is
interpreted as such when booting, and causes the system to enter
failsafe, if the tray is missing. Similarly to rfkill switch on
TP-Link WDR4300 and Archer C7, make it EV_SW instead, to stop it from
interfering with the boot process.

Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17503
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit 7b9ca01109827368deb68b7d8217643b78b87cb9)

ath79: teltonika-rut230: fix typo in "green:signal-strength4" LED

It's missing a hyphen present in every other LED from the set. Set it to
"green:signal-strength-4".

Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17503
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit d04f41e092294789b5add6816bb3b3bd7570a30d)

apm821xx: fixes WNDAP620 + WNDAP660 sysupgrade failures

OpenWRT on the WNDAP6x0 refuses to sysupgrade to itself
due to a compat_version imbalance. The Image is generated
with version 2.0, but the uci-defaults says that it needs
to be at 3.0 for the device.

Fix this by downgrading WNDAP6x0 05_fix-compat-version's
values back to 2.0 so it matches what we use.

Fixes: 5815884c3a2a ("apm821xx: migrate to DSA")
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
(cherry picked from commit e9415be4ad3cacbbd6e65fee5213baf3eaf9e07a)

lantiq: xrx200_legacy: disable unused phy drivers

Subtarget xrx200_legacy supports only a few devices. They all use
the integrated Lantiq GSWIP switch and lantiq xway PHYs. The atheros
and icplus PHYs can be safely disabled.

Switches used by individual devices are listed below.

Device Switch PHY
Alpha ASL56026 Lantiq GSWIP int. switch
Arcadyan VG3503J Lantiq GSWIP int. switch
Netgear DM200 Lantiq GSWIP int. switch
TP-LINK TD-W8970 Lantiq GSWIP Lantiq PEF7071V
TP-Link TD-W8980 Lantiq GSWIP Lantiq PEF7071V

Reduces uncompressed kernel size by 16 kB.

Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
Link: https://github.com/openwrt/openwrt/pull/17581
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit 517b9c1cdcd357fd84c7f27bd2886f235f3ec946)

lantiq: xway_legacy: refresh config

This was done by executing these command:
$ make kernel_oldconfig CONFIG_TARGET=subtarget

Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
Link: https://github.com/openwrt/openwrt/pull/17581
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit 524e22b4c71366be86493ca3ee7a16ff92d52288)

lantiq: xrx200: add alternative names for Plusnet Hub One and BT Business Hub 5A

The Plusnet Hub One and BT Business Hub 5A have the same hardware as
the BT Home Hub 5A. This commit adds alternative names so that both
devices can be easily found in the firmware selector.

Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
Link: https://github.com/openwrt/openwrt/pull/17583
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit 1b045a7c13aeb141e0c069aaf5fc38989eee11cf)

lantiq: xrx200_legacy: add alternative names for TP-Link TD-W9980(B)

The TP-Link TD-W9980(B) shares the same hardware with the TP-Link TD-W8980.
The only difference is that the TD-W8980 does not support VDSL. This is a
software limitation and once the software is changed, both work equally
supporting VDSL. This commit adds alternative names for devices so they
can be easily found in the firmware selector.

Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
Link: https://github.com/openwrt/openwrt/pull/17583
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit b2b4ce15322c75bda0cae6fb2160a74270185831)

kernel: bump 6.6 to 6.6.71

Changelog: https://cdn.kernel.org/pub/linux/kernel/v6.x/ChangeLog-6.6.71

Manually rebased:
airoha/patches-6.6/110-01-clk-en7523-Rework-clock-handling-for-different-clock.patch
airoha/patches-6.6/111-mmc-mtk-sd-add-support-for-AN7581-MMC-Host.patch

All other patches automatically rebased.

Build system: x86/64
Build-tested: bcm27xx/bcm2712
Run-tested: bcm27xx/bcm2712

Signed-off-by: John Audia <therealgraysky@proton.me>
[ fix manually rebased patch ]
Link: https://github.com/openwrt/openwrt/pull/17568
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
(cherry picked from commit 3f87c5ac4221deb37d4c3e730e692eef8f9c9ffe)

kernel: bump 6.6 to 6.6.70

Changelog: https://cdn.kernel.org/pub/linux/kernel/v6.x/ChangeLog-6.6.70

Removed upstreamed:
generic/backport-6.6/902-net-llc-reset-skb-transport_header.patch[1]
generic/pending-6.6/605-netfilter-nft_set_hash-unaligned-atomic-read-on-stru.patch[2]

All other patches automatically rebased.

1. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v6.6.70&id=0c896816aa193e6459fc947747e5753c06b395b9
2. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v6.6.70&id=4f49349c1963e507aa37c1ec05178faeb0103959

Build system: x86/64
Build-tested: bcm27xx/bcm2712, flogic/xiaomi_redmi-router-ax6000-ubootmod, ramips/tplink_archer-a6-v3
Run-tested: bcm27xx/bcm2712, flogic/xiaomi_redmi-router-ax6000-ubootmod, ramips/tplink_archer-a6-v3

Signed-off-by: John Audia <therealgraysky@proton.me>
Link: https://github.com/openwrt/openwrt/pull/17545
Signed-off-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit efafd7d47f8fa26a9f99283605c9324a833ef852)

rockchip: disable kernel preemption

This setting is more suitable for device running OpenWRT.
Most OpenWRT targets are already default to this configuration,
and it has shown better performance in VPN (wireguard).

Fix: #17454

Signed-off-by: Kien Truong <duckientruong@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17575
Signed-off-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit 1c178f364454c5b73eb453fa0b101ae2f6454d4c)

airoha: an7581: refresh DTS with changes for cpufreq, MTD and MMC

Refresh DTS with required changes for cpufreq, MTD and MMC. While at it
also fix wrong speed for MAC.

Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
(cherry picked from commit 17b0d1379a3cd4a2e2dbefa7d0f9bc281269f97e)

airoha: an7581: replace cpufreq patch with new version

Replace cpufreq patch with new version requested upstream.

Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
(cherry picked from commit 506955735075241d3467d632cae7ed5f10e21c2f)

airoha: an7581: add pending patch for ETS qdisc on ethernet driver

Add pending patch for ETS qdisc on Airoha ethernet driver.

Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
(cherry picked from commit 53bc7633317a7da9bf7ef440ed3da39404cf146e)

airoha: an7581: add pending patch to fix PCI

Add pending patch to fix PCIe missing register.

Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
(cherry picked from commit 77329b7d8d870897d85270a4e806ec0d04396685)

airoha: an7581: add patch fixing support for MMC

Add patch fixing support for MMC. Additional clock are needed for MMC to
work and some small fixup to make the Mediatek MMC driver on Airoha SoC.

Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
(cherry picked from commit be5a9ff24b9c3b7d1b5bf508b84a35be9f9b3ea9)

kernel: modules: Add ETS Qdisc scheduler to sched KernelPackage

Add ETS Qdisch scheduler to kernel package modules.

Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
[ add commit description ]
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
(cherry picked from commit 7e237f190225c0bcba0f5374632d0508f11398a8)

airoha: an7581: backport patch to support ETS and HTB sched

Backport patch to support ETS and HTB scheduler for airoha ethernet
driver.

Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
(cherry picked from commit 3ec3ea5316ceebae260f4d170c6e1c3a19864438)

airoha: an7581: backport 2 fix for airoha ethernet driver

Backport 2 fix for airoha ethernet driver merged upstream.

Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
(cherry picked from commit b4ae5378d403aa263ba5ec26ccc333ab0de81cff)

airoha: an7581: replace BUS clock patch with upstream version

Replace BUS clock patch with upstream version with related tag
as it got approved and merged.

Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
(cherry picked from commit 07b49ce87660a0448c0535b481b330e1bd333a8c)

airoha: an7581: enable MMC and PCI and refresh config

Enable MMC and PCI config symbol and refresh config for Airoha AN7581.

Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
(cherry picked from commit 73d368868c9dd2facfdf3f58533ee6310b2a665c)

lantiq: Remove legacy LED migration script

This script was rendered obsolete after xrx200 target switched to DSA and
breaking config migration from old releases to 22.03.

Signed-off-by: Mustafa Can Elmacı <mustafacan@elmaci.net>
Link: https://github.com/openwrt/openwrt/pull/17383
Link: https://github.com/openwrt/openwrt/pull/17512
Signed-off-by: Robert Marko <robimarko@gmail.com>

lantiq: fritz7430: fix PCI ID

This platform has a bogus PCI ID for the chip. Correct it in DTS.

Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16555
Link: https://github.com/openwrt/openwrt/pull/17512
Signed-off-by: Robert Marko <robimarko@gmail.com>

lantiq: use nvmem for tplink tdw89x0

These two devices use different wifi chips and as a result, different
calibration sizes. Move the differences out of dtsi.

Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16555
Link: https://github.com/openwrt/openwrt/pull/17512
Signed-off-by: Robert Marko <robimarko@gmail.com>

lantiq: use nvmem for fritz 736x

Two use AR9287 and one AR9381. Both have different calibration sizes.
Move differences out of wifi node to make it clearer what's what.

qca,no-eeprom needs to stay for 7362sl as there's no nvmem equivalent
for caldata_extract_reverse

Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17278
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Link: https://github.com/openwrt/openwrt/pull/17512
Signed-off-by: Robert Marko <robimarko@gmail.com>

lantiq: use nvmem for fritz73x0

These units use AR9287, which has a calibration size of 3d8.

Also fixed compatible string to the proper one to indicate AR9287.

Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17278
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Link: https://github.com/openwrt/openwrt/pull/17512
Signed-off-by: Robert Marko <robimarko@gmail.com>

lantiq: use regulator for USB GPIO

One is already present. The other one can be implemented in terms of the
PHY.

Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17250
Signed-off-by: John Crispin <john@phrozen.org>
Link: https://github.com/openwrt/openwrt/pull/17512
Signed-off-by: Robert Marko <robimarko@gmail.com>

ipq40xx: fix label MAC address for Linksys WHW03 v2

The label MAC address is written inside the case of the whw03 v2 at the bottom.

Similar fix as to the 4040 in b22d382ae4eaa1af42930115d91855f402314cac

Signed-off-by: Florian Maurer <f.maurer@outlook.de>
Link: https://github.com/openwrt/openwrt/pull/17535
Signed-off-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit c113982706989c76c69e94e15abce0d316e97f6b)

ipq40xx: dts: add ethernet0 alias for all devices

Updating the driver patches for ipq40xx (correctly) removed the
ethernet0 alias from qcom-ipq4019.dtsi; however, on some devices this
alias is needed for the bootloader to set MAC addresses in the FDT.

As it is unknown which devices actually need the alias, simply add it to
all devices trees for now that enable the &gmac now to avoid regressions
from previous OpenWrt releases. The additional alias should not cause any
issues even when it is not needed.

A TODO comment is added to the same Device Trees to document that the
alias may not be needed (hopefully preventing it from being copied
unnecessarily to newly added devices in the future). The following
devices are known to need the alias for correct MAC address assignment,
so no TODO comment is added:

- FRITZ!Box 4040
- FRITZ!Box 7530

Fixes: cd9c7211241e ("ipq40xx: 6.1: use latest DSA and ethernet patches")
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
Link: https://github.com/openwrt/openwrt/pull/17442
Signed-off-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit d09dd75fbd1314ec5f3571511195da4012d7a51a)

generic: add gpio-regmap request/free ops patch

This patch is needed on bmips since it fixes issues with GPIOs not being
properly configured due to gpio_request_enable not being called on bcm63xx
devices. Therefore we can now drop the bcm63268 gpio function patch.

Backported from f5b1d340be9488af71e6522c3f10f1ebd1a35446 with the exception of
the realtek patch removal.

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
(cherry picked from commit f5b1d340be9488af71e6522c3f10f1ebd1a35446)

mac80211: set basic-rate for mesh interfaces

Basic rates were not set for mesh-interfaces, resulting in the undesired
behavior where 11s frames might be sent with a rate which was not
configured.

Depending on the driver, the basic rate might also be used to determine
the beacon rate configured to the chip. One such example are MediaTek
MT7915 platforms.

Signed-off-by: David Bauer <mail@david-bauer.net>
(cherry picked from commit 3ec7f3a512a27f8ca6402954ad2a997176103b4b)

ath79: reset ETH switch for AR9344

According to datasheet, on AR9344 the switch and switch analog need to
be reset first before initiating a full reset.

Resetting these systems fixes spurious reset hangs on Atheros AR9344
SoCs.

Link: https://github.com/freifunk-gluon/gluon/issues/2904
Signed-off-by: David Bauer <mail@david-bauer.net>
(cherry picked from commit 916af73fc388d638b1a717a2411792e0680dd8e6)

OpenWrt v24.10.0-rc5: revert to branch defaults

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>

OpenWrt v24.10.0-rc5: adjust config defaults

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>

mediatek/filogic: add support for Cudy AP3000 v1

Hardware:
  SoC:     MT7981b
  RAM:     512 MB
  Flash:   256 MB SPI NAND
  Ethernet:
    1x2.5Gbps (rtl8221b)
  WiFi:    2x2 MT7981
  Button:  Reset
  LED:     1x multicolor

Installation
------------
At the moment, firmware installation is only possible via a transition firmware.
It's can be requested from the manufacturer by email to support@cudy.com

Signed-off-by: Maxim Anisimov <maxim.anisimov.ua@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17225
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit 6992d6e51af34603de099d7bbe9d7e848f109e22)

mediatek: Fix U-Boot variables handling for D-Link M30 A1

I think I implemented the U-Boot handling incorrectly on M30 (saw the issue while porting M60 to OpenWrt). Maybe someone with more U-Boot experience can have a look at it.
What I understood until now:

Before flashing, `sw_tryactive` must be set to 0 because OpenWrt runs on partition 0

During reset after flashing, U-Boot executes the following line:
`boot_rd_auto_sw_img=if itest.s ${sw_tryactive} == 2; then run boot_by_part; else run boot_by_tryactive; fi`

As `sw_tryactive` was set to 0 before flashing, `boot_by_tryactive` will be executed:
`boot_by_tryactive=if itest.s ${sw_tryactive} == 0; then setenv sw_tryactive 2; setenv sw_active 1; saveenv; run ub0; else setenv sw_tryactive 2; setenv sw_active 2; saveenv; run ub1; fi`

As `sw_tryactive` was set to 0 before flashing, `sw_active` will be set to 1 and `ub0` will be executed:
`ub0=setenv bootpart 0; mtkboardboot; run ub0to1; uip main; reset`

If the OpenWrt boot is successful, `ub0to1` and `uip` main will never be executed. Only in case OpenWrt cannot be loaded, `mtkboardboot` will return and the fallback `ub0to1` is executed.

Conclusion: It's sufficient to set `sw_tryacitve` to 0 before flashing, the added code in `target/linux/mediatek/filogic/base-files/etc/init.d/bootcount` is useless.
In the worst case (/proc/cmdline doesn't contain `bootpart=ubi0` as expected), the bootpart variable would be set to 1 and causes starting the firmware from the second partition instead of the one on the first partition.

Signed-off-by: Roland Reinl <reinlroland+github@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17298
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit 70610a5240a94648e178713f091435bd0ba158d3)

mac80211: rt2x00: some improvements for rt5592

This patch contains some performance and stability improvements
for RT5592:

1. Fix RFCSR register init values for RT5592.
2. Fix BBP register init values for RT5592.

Signed-off-by: Shiji Yang <yangshiji66@qq.com>
Link: https://github.com/openwrt/openwrt/pull/16845
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit 59557ca19a460d8ad70991f63616d1ad0dfe9823)

mac80211: rt2x00: some improvements for mt7620

This patch contains some performance and stability improvements
for MT7620:

1. Always calibrate MT7620 when switching channel.
2. Rework link tuner for MT7620.
3. Correct MT7620 SDM mode register value.
4. Fix register operation on RXIQ calibration.
5. Fix TX_PIN_CFG and TX_ALC_VGA3 init values.

Signed-off-by: Shiji Yang <yangshiji66@qq.com>
Link: https://github.com/openwrt/openwrt/pull/16845
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit 5d583901657bdfbbf9fad77d9247872427aa5c99)

mac80211: rt2x00: some improvements for rt2800 generic

1. Respect the rt2800 hardware TX queue index.
2. Increase the watchdog sampling frequency.

Signed-off-by: Shiji Yang <yangshiji66@qq.com>
Link: https://github.com/openwrt/openwrt/pull/16845
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit 70733c6093ee1e2fae12fdff97425270ea733dae)

realtek: trim default package selection

Images for certain devices are staring to become too large, as some
device only have 6MB available in their vendor partition layout for the
initial install. This is especially pressing for bootloaders only
supporting gzip compression.

Drop some packages from DEFAULT_PACKAGES that aren't strictly required
for a factory install. The user can always install more packages later
using opkg/apk, or via a sysupgrade to a custom build.

firewall4 is kept to ensure the most recent firewall package is selected
in builds including LuCI.
ethtool is kept as a frequently used diagnostics tool.

Link: https://github.com/openwrt/openwrt/pull/17450
Signed-off-by: Sander Vanheule <sander@svanheule.net>
(cherry picked from commit c9ae39b2d156ff893d88a7d75b9044aac2fdd8d0)

ath79: Push MV88E6060 DSA switch into package

We can use a package for the MV88E6060 DSA switch on the single
ath79 device that uses it, saving around 600 KB of memory on
all other devices (for the DSA infrastructure, mainly).

As far as I can see the TP-Link TL WR941 v2 is the only device
using MV88E6060 and the only device with a DSA switch overall.

However the ath79 people should look at this so I'm not
mistaken.

Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://patchwork.ozlabs.org/project/openwrt/patch/20250102-ath79-mv88e6060-module-v1-1-c2a8e31e72fc@linaro.org/
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit e7419381fdd43a49e7583a786ce2d9c2ed1b4afe)

ixp4xx: Break out mv88e6060 DSA switch to package

Just one of the devices uses the Marvell MV88E6060 DSA
switch so break this out from the generic kernel config
and into a package selected only by that single device
and probed at boot instead.

The big win is from being able to drop the dsa_core
(~600KB) kernel module out of the common kernel on
devices with no DSA switch.

Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
(cherry picked from commit 2456a2fd7f72d6afcee4ac9c2eccb312d0b1d36d)

mediatek: append metadata to factory-uboot.bin for WSR devices

Append metadata to factory-uboot.bin image to pass the image verification
on sysupgrade.

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17408
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit a06a2ef89db03fac2cbd950304e5b507da9deb1e)

lantiq: xrx200: add support for lan3 and lan4 on AVM 5490/5491

On the AVM 5490/5491, lan1, lan2 and wan ports are connected directly
to the internal GSWIP switch. The lan3 and lan4 ports are connected via
an external QCA8334 switch. This commit adds the missing entries in dts
and adds the driver module.

Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
Link: https://github.com/openwrt/openwrt/pull/17473
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit 14be320291e0c00a1291ad8bd220fd37b12ba138)

base-files: strip space and tab characters from ASCII mac address

Spaces and tabs are widely used in variable definitions. We have to
remove them to ensure that get_mac_ascii() works properly.

Signed-off-by: Shiji Yang <yangshiji66@qq.com>
Link: https://github.com/openwrt/openwrt/pull/17262
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit 551e04f3c9c063d885ca7a91db36f27f684a3a5c)

base-files: enable get_mac_ascii() to handle redundant strings

The function get_mac_ascii() will fail when there are two or more
same MAC address variable names in the mtd partition. Only retain
the first variable to workaround this rare situation.

Fixes: https://github.com/openwrt/openwrt/issues/17236
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
Link: https://github.com/openwrt/openwrt/pull/17262
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit 3410ad2f40c085e5db7a71f6ae4b80734826a1e3)

uboot-mediatek: add missing LED command for OpenWrt One

The u-boot LED command "led_loop_done" is missing from the OpenWrt
One NAND flash u-boot. Copy it from the OpenWrt One NOR flash u-boot
default environment to fix this issue.

Fixes: https://github.com/openwrt/openwrt/issues/17310
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
Link: https://github.com/openwrt/openwrt/pull/17338
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit 5ef71eaafd4e128ec3708a66b5633214427da373)

uboot-mediatek: fix Routerich AX3000 support patch

It seems that the original patch has been manually modified. The
newly added line number is incorrect.

Fixes: c0581520b1c5 ("uboot-mediatek: add Routerich AX3000 support")
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
Link: https://github.com/openwrt/openwrt/pull/17338
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit 9f97e39a9336e279be7ea1c00c4221ec3f448457)

ramips: mtk-mmc: remove nt76x8 pinctrl hack

Now we can set the mt76x8 SDXC pinmux in device tree.

Signed-off-by: Shiji Yang <yangshiji66@qq.com>
Link: https://github.com/openwrt/openwrt/pull/17446
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit b4a9f85c1394f13806fc2f51f5f6f23494773d7e)

ramips: make package kmod-sdhci-mt7620 conflict with kmod-mmc-mtk

These two packages are SDXC drivers for Mediatek mt762x series SoCs.
One is upstream implementation, and the other is downstream driver.
Installing them together will result in conflicts.

Signed-off-by: Shiji Yang <yangshiji66@qq.com>
Link: https://github.com/openwrt/openwrt/pull/17446
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit 0764e3008228bbdafb5e4a9837fe9efec7e138a0)

ramips: fix SDXC function for mt76x8 one eth port devices

There are only 5 devices in mt76x8 sub-target selected the MTK SDXC
driver package. And they are all single ethernet port routers or dev
boards:

* LinkIt Smart 7688
* Onion Omega2+
* RAVPower RP-WD009
* VoCore VoCore2
* VoCore VoCore2-Lite

For these devices, they are using the ephy p1 - p4 as the SDXC IO
pins. Therefore, these GPIO pads must be configured in "digital"
IO mode.

Signed-off-by: Shiji Yang <yangshiji66@qq.com>
Link: https://github.com/openwrt/openwrt/pull/17446
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit f5996ae947c88461029060d74ace6a85a30dd9fd)

ramips: add back SDXC card reader support for HiWiFi HC5x61A

After adding the correct package and pin group configurations,
the SDXC card slot can now function properly.

Signed-off-by: Shiji Yang <yangshiji66@qq.com>
Link: https://github.com/openwrt/openwrt/pull/17446
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit cea4aae0a921d71407d11957502f8cc3b652be21)

ramips: mmc-mtk: add more vendor driver register init values

In the MTK vendor driver, mt762x SDXC registers MSDC_PATCH_BIT and
MSDC_PATCH_BIT1 have different init values than upstream driver.
These magical values should have some help for the stability.

Signed-off-by: Shiji Yang <yangshiji66@qq.com>
Link: https://github.com/openwrt/openwrt/pull/17446
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit f70cdfd682a87c9de942f9251fb5a0caaf43f7cf)

ramips: mt762{0,8}: reduce default MMC clock to 24 MHz

The upstream mtk-sd driver did not perform specific timing
optimization for MT762x series SoC, hence the SDHC peripheral
of some boards cannot run at too high frequency. Reduce the
maximum clock frequency to fix the mmc read/write error.

Closes: https://github.com/openwrt/openwrt/issues/17364
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
Link: https://github.com/openwrt/openwrt/pull/17375
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit de0c143742517d401c4730137f092be8fb7e882a)

bcm27xx: remove duplicated kmod-rp1-pio package

Commit f105d1a9a9739267fb25612d039c392a397775bd added a duplicated
kmod-rp1-pio package.
Also remove unneeded blank lines added by the same commit.

Fixes: f105d1a9a973 ("bcm27xx/bcm2712: Fix-up RP1 modules")
Signed-off-by: John Audia <therealgraysky@proton.me>
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
(cherry picked from commit d5669c040beb0fa29e6916049941f0e76ce07460)

rockchip: enable USB3 port on NanoPC T6

Enable the USB3 port on FriendlyELEC NanoPC-T6.

Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
Link: https://github.com/openwrt/openwrt/pull/17349
(cherry picked from commit 6881b48dc603e25320a14e11c5e1797321891b76)
Link: https://github.com/openwrt/openwrt/pull/17466
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>

rockchip: backport recent rk3588 clk updates

Backport recent rk3588 clk updates from upstream,
including one bug fix.

Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
Link: https://github.com/openwrt/openwrt/pull/17349
(cherry picked from commit 8ad02ca2f8477b1cfdc5ea6124fae60c07687aa1)
Link: https://github.com/openwrt/openwrt/pull/17466
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>

bcm27xx/bcm2712: Fix-up RP1 modules

Correct a few mistakes around dependencies and naming and unset
CONFIG_FIRMWARE_RP1 in RPi5B's config and instead of a builtin, build it
as a module.

Without this change, there are two entries for rp1.ko in
/lib/modules/$(uname -r)/modules.builtin due to how we strip the leading
directories when we generate it. See: package/kernel/linux/Makefile
around line 63.

  % grep rp1.ko /lib/modules/$(uname -r)/modules.builtin
  pwm-rp1.ko
  clk-rp1.ko
  rp1.ko
  rp1.ko

The kernel log gets spammed with tons of superfluous warnings as a
results of the double entry:

  daemon.warn modprobe: found duplicate builtin module rp1

Signed-off-by: John Audia <therealgraysky@proton.me>
Link: https://github.com/openwrt/openwrt/pull/17461
Signed-off-by: Robert Marko <robimarko@gmail.com>
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
(cherry picked from commit f105d1a9a9739267fb25612d039c392a397775bd)

wifi-scripts: fix setting tx power on some drivers

On some drivers, setting the tx power on the interface is not enough.
Set it for the phy as well.

Fixes: 04fb05914ea7 ("wifi-scripts: add multi-radio config support")
Signed-off-by: Felix Fietkau <nbd@nbd.name>
(cherry picked from commit b795e5cbcffc54e858bc8d3bde0031a2ca32377e)

mt76: update to Git HEAD (2025-01-04)

35bcf68a6297 wifi: mt76: scan: fix setting tx_info fields
4d8d6e2e7710 wifi: mt76: scan: set vif offchannel link for scanning/roc
e354436db440 wifi: mt76: mt7996: use the correct vif link for scanning/roc

Signed-off-by: Felix Fietkau <nbd@nbd.name>
(cherry picked from commit f11bc4f201e3a4ffec8c1e2083124ebda60dd763)

generic: 6.6: backport upstream r8169 patches

7a3bcd39ae1f r8169: use helper r8169_mod_reg8_cond to simplify rtl_jumbo_config
e3e9e9039fa6 r8169: align WAKE_PHY handling with r8125/r8126 vendor drivers
330dc2297c82 r8169: improve rtl_set_d3_pll_down
c507e96b5763 r8169: improve __rtl8169_set_wol
83cb4b470c66 r8169: remove leftover locks after reverted change
2cd02f2fdd8a r8169: improve initialization of RSS registers on RTL8125/RTL8126
a3d8520e6a19 r8169: align RTL8126 EEE config with vendor driver
4af2f60bf737 r8169: align RTL8125/RTL8126 PHY config with vendor driver
eb90f876b796 r8169: align RTL8125 EEE config with vendor driver
b8bd8c44a266 r8169: fix inconsistent indenting in rtl8169_get_eth_mac_stats
f75d1fbe7809 r8169: add support for RTL8125D
c4e64095c00c r8169: enable EEE at 2.5G per default on RTL8125B
d64113c6bb5e r8169: remove rtl_dash_loop_wait_high/low
1c105bacb160 r8169: avoid duplicated messages if loading firmware fails and switch to warn level
ac48430368c1 r8169: don't take RTNL lock in rtl_task()
e3fc5139bd8f r8169: implement additional ethtool stats ops
b8bf38440ba9 r8169: enable SG/TSO on selected chip versions per default
854d71c555df r8169: remove original workaround for RTL8125 broken rx issue
1ffcc8d41306 r8169: add support for the temperature sensor being available from RTL8125B

The following patches require backporting additional linux patches:
e2015942e90a r8169: replace custom flag with disable_work() et al
e340bff27e63 r8169: copy vendor driver 2.5G/5G EEE advertisement constraints

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
(cherry picked from commit 0eeba04a16fb72b13d90973ef8ba95f0549f973e)

generic: 6.6: backport upstream Realtek PHY patches

8989bad54113 net: phy: realtek: add RTL8125D-internal PHY
f87a17ed3b51 net: phy: realtek: merge the drivers for internal NBase-T PHY's

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
(cherry picked from commit fedb1f86b50986a962c899d7406566d991e030ee)

rockchip: refresh patch

Commit 8a477bafb4637e3499f69f569133039ce060559e backported an upstream patch
without refreshing the patches.

Fixes: 8a477bafb463 ("rockchip: fix phy reset on rk356x")
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17474
Signed-off-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit 484f670ed3d41e44375bfa7f8892e660d3c8c26a)

mbedtls: Deactivate ARIA block cipher by default

The ARIA block cipher is pretty uncommon in TLS, deactivate it for now.
This saves some space and reduces the possible variations and attack
vectors of mbedtls.

ARIA support was deactivated in OpenWrt 23.05 by default.

Link: https://github.com/openwrt/openwrt/pull/17342
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit 3c0ef48bc82cb11edd0b4fdbc4beaa3f95708967)

config: enable SECCOMP support for loongarch64

Make USE_SECCOMP selectable for loongarch64

Signed-off-by: Weijie Gao <hackpascal@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17335
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit b6b6148d7d19f7081551491192e161f46cb0bdb8)

procd: update to Git HEAD (2024-12-22)

42d3937 jail/seccomp: add support for loongarch64

Link: https://github.com/openwrt/openwrt/pull/17335
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit f69fc4c413357ab2e981f11eacd6101b6a59ab34)

rockchip: fix phy reset on rk356x

The commit 7160820d742a ("phy: rockchip: naneng-combphy: fix phy reset")
was backported to kernel 6.6 branch by upstream, however the correspond
dtsi fixes was not, resulting the following error:
```
[ 0.225521] rockchip-naneng-combphy fe830000.phy: error -ENOENT: failed to get phy reset
[ 0.227467] rockchip-naneng-combphy fe840000.phy: error -ENOENT: failed to get phy reset
```

So backport the dtsi fixes here manually.

Fixes: 89b2356b8c2f ("kernel: bump 6.6 to 6.6.69")
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
Link: https://github.com/openwrt/openwrt/pull/17468
Signed-off-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit 8a477bafb4637e3499f69f569133039ce060559e)

kernel: bump 6.6 to 6.6.69

Changelog: https://cdn.kernel.org/pub/linux/kernel/v6.x/ChangeLog-6.6.69

All patches automatically rebased.

Build system: x86/64
Build-tested: bcm27xx/bcm2712, flogic/xiaomi_redmi-router-ax6000-ubootmod, ramips/tplink_archer-a6-v3
Run-tested: bcm27xx/bcm2712, flogic/xiaomi_redmi-router-ax6000-ubootmod, ramips/tplink_archer-a6-v3

Signed-off-by: John Audia <therealgraysky@proton.me>
Link: https://github.com/openwrt/openwrt/pull/17459
Signed-off-by: Nick Hainke <vincent@systemli.org>
(cherry picked from commit 89b2356b8c2fd420b49bacaa865fb9bd24173ecc)

kernel: add workaround for page_pool_release warnings

defer_list skbs held by NAPI can block releasing page pools.
Work around this by scheduling rx softirq on all CPUs while trying to release
a page pool.

Signed-off-by: Felix Fietkau <nbd@nbd.name>
(cherry picked from commit 2b70b32aef9e8e1ff275872d551c610368079911)

ipq40xx: fix label MAC address for FritzBox 7520/7530

The MAC address of the GMAC is contained inside the CWMP-Account number on the label.

Similar fix as to the 4040 in b22d382ae4eaa1af42930115d91855f402314cac
Link #13240

Signed-off-by: Florian Maurer <f.maurer@outlook.de>
Link: https://github.com/openwrt/openwrt/pull/17467
Signed-off-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit b2b6955f80d05a8cec69f8497df8bed44cf3c64d)

ubus: update to Git HEAD (2025-01-02)

d996988ae55b libubus: close file descriptor after sending it from a request
afa57cce0aff libubus: add support for using channels

Signed-off-by: Felix Fietkau <nbd@nbd.name>
(cherry picked from commit f0df6e3a4a4996eca917fa17591b8f1d483dfa30)

config: rename SECCOMP to USE_SECCOMP

It seems that we have some kind of a symbol name conflict which causes
CONFIG_SECCOMP to always be read as y.

Unfortunatelly, I could not figure out what is causing this, but simply
renaming SECCOMP to USE_SECCOMP seems to properly work and leaves the
symbol unset unless arch dependencies are satisfied.

This fixes qoriq and others that dont support seccomp from failing due
to procd-seccomp package being selected to get included but it cannot be
built for them:
ERROR: unable to select packages:
procd-seccomp (no such package):
required by: base-files-1637~52b6c92479[procd-seccomp]

Fixes: 4c65359af49b ("build: fix including busybox, procd and apk/opkg in imagebuilder")
Link: https://github.com/openwrt/openwrt/pull/17048
Signed-off-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit a48ec449ccab0069e84a72837bf06ba543e53aec)

build: remove targetinfo invalidation based on .config

Target info no longer depends on config settings

Signed-off-by: Felix Fietkau <nbd@nbd.name>
(cherry picked from commit 3b661cfcf9158a3dc5be6f7e1e1340339c9423b5)

linux: fix missing default packages in profiles.json

Robert reported, that in firmware images generated by ASU, there is
`apk` package manager missing after the commit 44598c233dd9 ("build:
remove broken dependency of metadata on toplevel .config variables").

That is happening, because apk got removed from `default_packages` list in
`profiles.json`, which is being generated by `json_overview_image_info` Make
target, which uses `scripts/json_overview_image_info.py` helper script,
which gets the information from `DEFAULT_PACKAGES` Make variable.

So lets fix it by providing `DEFAULT_PACKAGES` variable when its needed.

The reason why we didn't added those packages as a dependency to
base-files like any other packages, was to allow disabling them (in
order to save space).

Fixes: #16969
Fixes: openwrt/asu/issues/1084
Fixes: 44598c233dd9 ("build: remove broken dependency of metadata on toplevel .config variables")
Reported-by: Robert Marko <robimarko@gmail.com>
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Link: https://github.com/openwrt/openwrt/pull/16986
Signed-off-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit 90f0be8521a8608b0932c1ccb747c0ef1a085910)

imagebuilder: move handling of DEFAULT_PACKAGES into shareable place

It seems, that handling of DEFAULT_PACKAGES is needed in more places, so
lets move it into dedicated include file so it can be easily shared.

Signed-off-by: Petr Štetiar <ynezz@true.cz>
Link: https://github.com/openwrt/openwrt/pull/16986
Signed-off-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit 40be892a020e37869cdc188cd9a09bb7dc0a6872)

build: fix including busybox, procd and apk/opkg in imagebuilder

Since the image builder pulls package lists from metadata directly,
add procd and busybox as depdendencies to base-files.
As for the package manager itself, since it can be disabled it needs
to be added directly in the image builder makefile

Fixes: 44598c233dd9 ("build: remove broken dependency of metadata on toplevel .config variables")
Signed-off-by: Felix Fietkau <nbd@nbd.name>
(cherry picked from commit 4c65359af49b6ccecd98987f842db5eba985f64b)