Rob Herring [Thu, 13 Apr 2017 15:03:51 +0000 (10:03 -0500)]
bluetooth: hci_uart: remove unused hci_uart_init_tty
There are no users of hci_uart_init_tty, so remove it.
Signed-off-by: Rob Herring <robh@kernel.org>
Cc: Marcel Holtmann <marcel@holtmann.org>
Cc: Gustavo Padovan <gustavo@padovan.org>
Cc: Johan Hedberg <johan.hedberg@gmail.com>
Cc: linux-bluetooth@vger.kernel.org
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Rob Herring [Thu, 13 Apr 2017 15:03:50 +0000 (10:03 -0500)]
dt-bindings: net: Add TI WiLink shared transport binding
Add serial slave device binding for the TI WiLink series of Bluetooth/FM/GPS
devices.
Signed-off-by: Rob Herring <robh@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: netdev@vger.kernel.org
Cc: devicetree@vger.kernel.org
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Sebastian Reichel [Thu, 13 Apr 2017 00:26:59 +0000 (02:26 +0200)]
Bluetooth: add nokia driver
This adds a driver for the Nokia H4+ protocol, which is used
at least on the Nokia N9, N900 & N950.
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Sebastian Reichel [Thu, 13 Apr 2017 00:26:58 +0000 (02:26 +0200)]
dt-bindings: net: bluetooth: Add nokia-bluetooth
Add binding document for serial bluetooth chips using
Nokia H4+ protocol.
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Sebastian Reichel [Tue, 28 Mar 2017 15:59:37 +0000 (17:59 +0200)]
Bluetooth: hci_serdev: allow modular drivers
For bluetooth protocol driver only supporting serdev it makes
sense to follow common practice and built them into their own
module.
Such modules need access to hci_uart_register_device and
hci_uart_tx_wakeup for using the common protocol helpers.
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Sebastian Reichel [Tue, 28 Mar 2017 15:59:36 +0000 (17:59 +0200)]
Bluetooth: hci_serdev: do not open device in hci open
The device driver may need to communicate with the UART
device while the Bluetooth device is closed (e.g. due
to interrupts).
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Rob Herring [Tue, 28 Mar 2017 15:59:35 +0000 (17:59 +0200)]
Bluetooth: hci_uart: add serdev driver support library
This adds library functions for serdev based BT drivers. This is largely
copied from hci_ldisc.c and modified to use serdev calls. There's a little
bit of duplication, but I avoided intermixing this as the ldisc code should
eventually go away.
Signed-off-by: Rob Herring <robh@kernel.org>
Cc: Marcel Holtmann <marcel@holtmann.org>
Cc: Gustavo Padovan <gustavo@padovan.org>
Cc: Johan Hedberg <johan.hedberg@gmail.com>
Cc: linux-bluetooth@vger.kernel.org
Acked-by: Pavel Machek <pavel@ucw.cz>
[Fix style issues reported by Pavel]
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Sebastian Reichel [Tue, 28 Mar 2017 15:59:34 +0000 (17:59 +0200)]
Bluetooth: hci_uart: add support for word alignment
This will be used by Nokia's H4+ protocol, which
uses 2-byte aligned packets.
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Sebastian Reichel [Tue, 28 Mar 2017 15:59:33 +0000 (17:59 +0200)]
serdev: add helpers for cts and rts handling
Add serdev helper functions for handling of cts and rts
lines using the serdev's tiocm functions.
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Sebastian Reichel [Tue, 28 Mar 2017 15:59:32 +0000 (17:59 +0200)]
serdev: implement get/set tiocm
Add method for getting and setting tiocm.
Acked-by: Pavel Machek <pavel@ucw.cz>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Sebastian Reichel [Tue, 28 Mar 2017 15:59:31 +0000 (17:59 +0200)]
serdev: add serdev_device_wait_until_sent
Add method, which waits until the transmission buffer has been sent.
Note, that the change in ttyport_write_wakeup is related, since
tty_wait_until_sent will hang without that change.
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Sebastian Reichel [Tue, 28 Mar 2017 15:59:30 +0000 (17:59 +0200)]
tty: serial: omap: add UPF_BOOT_AUTOCONF flag for DT init
The UPF_BOOT_AUTOCONF flag is needed for proper
flow control support.
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Patrik Flykt [Tue, 11 Apr 2017 19:21:03 +0000 (22:21 +0300)]
bluetooth: Do not set IFF_POINTOPOINT
The IPv6 stack needs to send and receive Neighbor Discovery
messages. Remove the IFF_POINTOPOINT flag.
Signed-off-by: Patrik Flykt <patrik.flykt@linux.intel.com>
Acked-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Reviewed-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Luiz Augusto von Dentz [Tue, 11 Apr 2017 19:21:02 +0000 (22:21 +0300)]
Bluetooth: 6lowpan: Set tx_queue_len to DEFAULT_TX_QUEUE_LEN
Make netdev queue packets if we run out of credits.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Acked-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Luiz Augusto von Dentz [Tue, 11 Apr 2017 19:21:01 +0000 (22:21 +0300)]
Bluetooth: L2CAP: Add l2cap_le_flowctl_send
Consolidate code sending data to LE CoC channels and adds proper
accounting of packets sent, the remaining credits and how many packets
are queued.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Acked-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Luiz Augusto von Dentz [Tue, 11 Apr 2017 19:21:00 +0000 (22:21 +0300)]
Bluetooth: 6lowpan: Use netif APIs to flow control
Rely on netif_wake_queue and netif_stop_queue to flow control when
transmit resources are unavailable.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Acked-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Luiz Augusto von Dentz [Tue, 11 Apr 2017 19:20:59 +0000 (22:20 +0300)]
Bluetooth: 6lowpan: Don't drop packets when run out of credits
Since l2cap_chan_send will now queue the packets there is no point in
checking the credits anymore.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Acked-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Luiz Augusto von Dentz [Tue, 11 Apr 2017 19:20:58 +0000 (22:20 +0300)]
6lowpan: Don't set IFF_NO_QUEUE
There is no point in setting IFF_NO_QUEUE should already have taken
care of setting it if tx_queue_len is not set, in fact this may
actually disable queue for interfaces that require it and do set
tx_queue_len.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Acked-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Luiz Augusto von Dentz [Mon, 3 Apr 2017 14:48:57 +0000 (17:48 +0300)]
Bluetooth: L2CAP: Don't return -EAGAIN if out of credits
Just keep queueing them into TX queue since the caller might just have
to do the same and there is no impact in adding another packet to the
TX queue even if there aren't any credits to transmit them.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Acked-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Luiz Augusto von Dentz [Mon, 3 Apr 2017 14:48:56 +0000 (17:48 +0300)]
Bluetooth: 6lowpan: Print errors during recv_pkt
This makes should make it more clear why a packet is being dropped.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Acked-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Luiz Augusto von Dentz [Mon, 3 Apr 2017 14:48:55 +0000 (17:48 +0300)]
Bluetooth: 6lowpan: Remove unnecessary peer lookup
During chan_recv_cb there is already a peer lookup which can be passed
to recv_pkt directly instead of the channel.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Acked-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Xinming Hu [Fri, 31 Mar 2017 06:32:32 +0000 (14:32 +0800)]
Bluetooth: btmrvl: remove unnecessary wakeup interrupt number sanity check
Sanity check of interrupt number in interrupt handler is unnecessary and
confusion, remove it.
Reported-by: Guenter Roeck <groeck@chromium.org>
Signed-off-by: Xinming Hu <huxm@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Xinming Hu [Fri, 31 Mar 2017 06:32:31 +0000 (14:32 +0800)]
Bluetooth: btmrvl: disable platform wakeup interrupt in suspend failure path
Host sleep handshake with device might been fail, disable platform wakeup
interrupt in this case.
Reported-by: Guenter Roeck <groeck@chromium.org>
Signed-off-by: Xinming Hu <huxm@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Michael Scott [Wed, 29 Mar 2017 06:10:18 +0000 (23:10 -0700)]
Bluetooth: 6lowpan: fix use after free in chan_suspend/resume
A status field in the skb_cb struct was storing a channel status
based on channel suspend/resume events. This stored status was
then used to return EAGAIN if there were packet sending issues
in snd_pkt().
The issue is that the skb has been freed by the time the callback
to 6lowpan's suspend/resume was called. So, this generates a
"use after free" issue that was noticed while running kernel tests
with KASAN debug enabled.
Let's eliminate the status field entirely as we can use the channel
tx_credits to indicate whether we should return EAGAIN when handling
packets.
Signed-off-by: Michael Scott <michael.scott@linaro.org>
Acked-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Michael Scott [Wed, 29 Mar 2017 06:10:54 +0000 (23:10 -0700)]
Bluetooth: 6lowpan: fix delay work init in add_peer_chan()
When adding 6lowpan devices very rapidly we sometimes see a crash:
[23122.306615] CPU: 2 PID: 0 Comm: swapper/2 Not tainted 4.9.0-43-arm64 #1 Debian 4.9.9.linaro.43-1
[23122.315400] Hardware name: HiKey Development Board (DT)
[23122.320623] task:
ffff800075443080 task.stack:
ffff800075484000
[23122.326551] PC is at expire_timers+0x70/0x150
[23122.330907] LR is at run_timer_softirq+0xa0/0x1a0
[23122.335616] pc : [<
ffff000008142dd8>] lr : [<
ffff000008142f58>] pstate:
600001c5
This was due to add_peer_chan() unconditionally initializing the
lowpan_btle_dev->notify_peers delayed work structure, even if the
lowpan_btle_dev passed into add_peer_chan() had previously been
initialized.
Normally, this would go unnoticed as the delayed work timer is set for
100 msec, however when calling add_peer_chan() faster than 100 msec it
clears out a previously queued delay work causing the crash above.
To fix this, let add_peer_chan() know when a new lowpan_btle_dev is passed
in so that it only performs the delay work initialization when needed.
Signed-off-by: Michael Scott <michael.scott@linaro.org>
Acked-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Johan Hovold [Wed, 29 Mar 2017 16:15:28 +0000 (18:15 +0200)]
Bluetooth: hci_intel: add missing tty-device sanity check
Make sure to check the tty-device pointer before looking up the sibling
platform device to avoid dereferencing a NULL-pointer when the tty is
one end of a Unix98 pty.
Fixes: 74cdad37cd24 ("Bluetooth: hci_intel: Add runtime PM support")
Fixes: 1ab1f239bf17 ("Bluetooth: hci_intel: Add support for platform driver")
Cc: stable <stable@vger.kernel.org> # 4.3
Cc: Loic Poulain <loic.poulain@intel.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Johan Hovold [Wed, 29 Mar 2017 16:15:27 +0000 (18:15 +0200)]
Bluetooth: hci_bcm: add missing tty-device sanity check
Make sure to check the tty-device pointer before looking up the sibling
platform device to avoid dereferencing a NULL-pointer when the tty is
one end of a Unix98 pty.
Fixes: 0395ffc1ee05 ("Bluetooth: hci_bcm: Add PM for BCM devices")
Cc: stable <stable@vger.kernel.org> # 4.3
Cc: Frederic Danis <frederic.danis@linux.intel.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Colin Ian King [Wed, 29 Mar 2017 17:05:40 +0000 (18:05 +0100)]
ieee802154: ca8210: Add checks for kmalloc allocation failures
Ensure we don't end up with a null pointer dereferences by checking
for for allocation failures. Allocate by sizeof(*ptr) rather than
the type to fix checkpack warnings. Also merge multiple lines into
one line for the kmalloc call.
Detected by CoverityScan, CID#
1422435 ("Dereference null return value")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
prasanna karthik [Tue, 28 Mar 2017 19:44:00 +0000 (19:44 +0000)]
Bluetooth: btmrvl: cleanup code in return from btmrvl_sdio_suspend()
Else is not generally useful after a break or return
Signed-off-by: Prasanna Karthik <pkarthik@outlook.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Colin Ian King [Tue, 28 Mar 2017 12:11:29 +0000 (13:11 +0100)]
6lowpan: fix assignment of peer_addr
The data from peer->chan->dst is not being copied to peer_addr, the
current code just updates the pointer and not the contents of what
it points to. Fix this with the intended assignment.
Detected by CoverityScan, CID#
1422111 ("Parse warning
(PW.PARAM_SET_BUT_NOT_USED)")
Fixes: fb6f2f606ce8 ("6lowpan: Fix IID format for Bluetooth")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Harry Morris [Tue, 28 Mar 2017 12:09:00 +0000 (13:09 +0100)]
ieee802154: Add entry in MAINTAINTERS for CA8210 driver
Signed-off-by: Harry Morris <h.morris@cascoda.com>
Acked-by: Stefan Schmidt <stefan@osg.samsung.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Harry Morris [Tue, 28 Mar 2017 12:08:59 +0000 (13:08 +0100)]
ieee802154: Add device tree documentation for CA8210
Signed-off-by: Harry Morris <h.morris@cascoda.com>
Acked-by: Stefan Schmidt <stefan@osg.samsung.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Harry Morris [Tue, 28 Mar 2017 12:08:58 +0000 (13:08 +0100)]
ieee802154: Add CA8210 IEEE 802.15.4 device driver
Add driver source and config for softMAC implementation of Cascoda's CA8210
IEEE 802.15.4 transceiver device. The driver mimics a common PHY-only
implementation despite the CA8210 being a hardMAC device which exposes a SAP
interface to the fully integrated MAC.
The chip is a modem-only device with an integrated processor which runs the
802.15.4 MAC. The chip communicates via full-duplex SPI with additional pins
for NIRQ and NRESET. The chip can also output its 16MHz clock to a GPIO with a
configurable divider.
The driver can be configured to implement a debugfs node that provides access
to the SAP-based API to drive mechanisms not currently supported by the
standard kernel interface.
Signed-off-by: Harry Morris <h.morris@cascoda.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Andy Shevchenko [Fri, 10 Mar 2017 12:28:20 +0000 (14:28 +0200)]
Bluetooth: hci_bcm: Support platform enumeration
Until now the driver supports only ACPI enumeration. Nevertheless
Intel Edison SoM has Broadcom Wi-Fi + BT chip and neither ACPI nor DT
enumeration mechanism.
Enable pure platform driver in order to support Intel Edison SoM.
Cc: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Jeffy Chen [Fri, 24 Feb 2017 06:24:30 +0000 (14:24 +0800)]
Bluetooth: btmrvl: wake system up when receives a wake irq
Currrently we are disabling this wake irq after receiving it. If this
happens before we finish suspend and the pm event check is disabled,
the system will continue suspending, and this irq would not work again.
We may need to abort system suspend to avoid that.
Signed-off-by: Jeffy Chen <jeffy.chen@rock-chips.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Jeffy Chen [Fri, 24 Feb 2017 06:24:29 +0000 (14:24 +0800)]
Bluetooth: btusb: wake system up when receives a wake irq
Currrently we are disabling this wake irq after receiving it. If this
happens before we finish suspend and the pm event check is disabled,
the system will continue suspending, and this irq would not work again.
We may need to abort system suspend to avoid that.
Signed-off-by: Jeffy Chen <jeffy.chen@rock-chips.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Larry Finger [Mon, 20 Feb 2017 02:04:57 +0000 (20:04 -0600)]
Bluetooth: btrtl: Change message for missing config file
The message concerning missing config files for 8723b, 8821a, and
8761a should have been issued with BT_INFO() rather than BT_ERR() as
this condition is not fatal. After looking at that code, I have
reworked the logic to log such messages only if the device needs such a
config file. At the moment, only the 8822b fits that description.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Acked-by: 陆朱伟 <alex_lu@realsil.com.cn>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Gabriel [Mon, 20 Feb 2017 17:32:22 +0000 (12:32 -0500)]
Bluetooth: Added support for Rivet Networks Killer 1535
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Jonas Holmberg [Thu, 23 Feb 2017 14:17:02 +0000 (15:17 +0100)]
Bluetooth: Change initial min and max interval
Use the initial connection interval recommended in Bluetooth
Specification v4.2 (30ms - 50ms).
Signed-off-by: Jonas Holmberg <jonashg@axis.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Colin Ian King [Wed, 1 Mar 2017 15:10:53 +0000 (15:10 +0000)]
Bluetooth: fix assignments on error variable err
Variable err is being initialized to zero and then later being
set to the error return from the call to hci_req_run_skb; hence
we can remove the redundant initialization to zero.
Also on two occassions err is not being set from the error return
from the call to hci_req_run_skb, so add these missing assignments.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Tedd Ho-Jeong An [Mon, 6 Mar 2017 23:38:35 +0000 (15:38 -0800)]
Bluetooth: hci_intel: Add support Intel Bluetooth device 9160/9260 for UART
This patch adds support for Intel Bluetooth device 9160/9260 also
known as ThunderPeak(ThP) for UART.
Signed-off-by: Tedd Ho-Jeong An <tedd.an@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Tedd Ho-Jeong An [Mon, 6 Mar 2017 23:38:32 +0000 (15:38 -0800)]
Bluetooth: hci_intel: Fix firmware file name to use hw_variant
The format of Intel Bluetooth firmware for bootloader product is
ibt-<hw_variant>-<device_revision_id>.sfi and .ddc.
This patch uses a hw_variant value read from the device during
runtime to form the firmware filenames instead of using a constant
value, so it can support multiple prouducts.
Signed-off-by: Tedd Ho-Jeong An <tedd.an@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Marcel Holtmann [Mon, 6 Mar 2017 23:38:28 +0000 (15:38 -0800)]
Bluetooth: btusb: Add support for Intel Bluetooth devices 9160/9260 [8087:0025]
The new Bluetooth devices 9160/9260 (also known as ThunderPeak)
devices from Intel use the same firmware loading mechanism as previous
generation. So include the new USB product identifier and whitelist
the hardware variant.
T: Bus=02 Lev=02 Prnt=03 Port=00 Cnt=01 Dev#= 8 Spd=12 MxCh= 0
D: Ver= 2.01 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=8087 ProdID=0025 Rev= 0.02
C:* #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=100mA
I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=81(I) Atr=03(Int.) MxPS= 64 Ivl=1ms
E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms
E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms
I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms
I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms
I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms
I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms
I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms
I: If#= 1 Alt= 6 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=03(O) Atr=01(Isoc) MxPS= 63 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 63 Ivl=1ms
Bluetooth: hci0: Bootloader revision 0.1 build 42 week 52 2015
Bluetooth: hci0: Device revision is 2
Bluetooth: hci0: Secure boot is enabled
Bluetooth: hci0: OTP lock is disabled
Bluetooth: hci0: API lock is disabled
Bluetooth: hci0: Debug lock is disabled
Bluetooth: hci0: Minimum firmware build 1 week 10 2014
< HCI Command: Read Local Version Information (0x04|0x0001) plen 0
> HCI Event: Command Complete (0x0e) plen 12
Read Local Version Information (0x04|0x0001) ncmd 1
Status: Success (0x00)
HCI version: Bluetooth 5.0 (0x09) - Revision 256 (0x0100)
LMP version: Bluetooth 5.0 (0x09) - Subversion 256 (0x0100)
Manufacturer: Intel Corp. (2)
Based on original patch from Jaya Praveen G <jaya.p.g@linux.intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Tested-by: Tedd Ho-Jeong An <tedd.an@intel.com>
Signed-off-by: Tedd Ho-Jeong An <tedd.an@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Tedd Ho-Jeong An [Mon, 6 Mar 2017 23:38:26 +0000 (15:38 -0800)]
Bluetooth: Use switch statement for Intel hardware variants
Multiple new hardware variants are planned and the simple if statement
would get really complicated and unreadable. So instead replace it with
a simple switch statement.
The change is applied to both USB and UART.
Based-on-patch-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Tedd Ho-Jeong An <tedd.an@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Marcin Kraglak [Wed, 8 Mar 2017 13:09:41 +0000 (14:09 +0100)]
Bluetooth: L2CAP: Fix L2CAP_CR_SCID_IN_USE value
Fix issue found during L2CAP qualification test TP/LE/CFC/BV-20-C.
Signed-off-by: Marcin Kraglak <marcin.kraglak@tieto.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Dean Jenkins [Fri, 10 Mar 2017 11:34:46 +0000 (11:34 +0000)]
Bluetooth: Avoid bt_accept_unlink() double unlinking
There is a race condition between a thread calling bt_accept_dequeue()
and a different thread calling bt_accept_unlink(). Protection against
concurrency is implemented using sk locking. However, sk locking causes
serialisation of the bt_accept_dequeue() and bt_accept_unlink() threads.
This serialisation can cause bt_accept_dequeue() to obtain the sk from the
parent list but becomes blocked waiting for the sk lock held by the
bt_accept_unlink() thread. bt_accept_unlink() unlinks sk and this thread
releases the sk lock unblocking bt_accept_dequeue() which potentially runs
bt_accept_unlink() again on the same sk causing a crash. The attempt to
double unlink the same sk from the parent list can cause a NULL pointer
dereference crash due to bt_sk(sk)->parent becoming NULL on the first
unlink, followed by the second unlink trying to execute
bt_sk(sk)->parent->sk_ack_backlog-- in bt_accept_unlink() which crashes.
When sk is in the parent list, bt_sk(sk)->parent will be not be NULL.
When sk is removed from the parent list, bt_sk(sk)->parent is set to
NULL. Therefore, add a defensive check for bt_sk(sk)->parent not being
NULL to ensure that sk is still in the parent list after the sk lock has
been taken in bt_accept_dequeue(). If bt_sk(sk)->parent is detected as
being NULL then restart the loop so that the loop variables are refreshed
to use the latest values. This is necessary as list_for_each_entry_safe()
is not thread safe so causing a risk of an infinite loop occurring as sk
could point to itself.
In addition, in bt_accept_dequeue() increase the sk reference count to
protect against early freeing of sk. Early freeing can be possible if the
bt_accept_unlink() thread calls l2cap_sock_kill() or rfcomm_sock_kill()
functions before bt_accept_dequeue() gets the sk lock.
For test purposes, the probability of failure can be increased by putting
a msleep of 1 second in bt_accept_dequeue() between getting the sk and
waiting for the sk lock. This exposes the fact that the loop
list_for_each_entry_safe(p, n, &bt_sk(parent)->accept_q) is not safe from
threads that unlink sk from the list in parallel with the loop which can
cause sk to become stale within the loop.
Signed-off-by: Dean Jenkins <Dean_Jenkins@mentor.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Dean Jenkins [Fri, 10 Mar 2017 11:34:45 +0000 (11:34 +0000)]
Bluetooth: Handle bt_accept_enqueue() socket atomically
There is a small risk that bt_accept_unlink() runs concurrently with
bt_accept_enqueue() on the same socket. This scenario could potentially
lead to a NULL pointer dereference of the socket's parent member because
the socket can be on the list but the socket's parent member is not yet
updated by bt_accept_enqueue().
Therefore, add socket locking inside bt_accept_enqueue() so that the
socket is added to the list AND the parent's socket address is set in the
socket's parent member. The socket locking ensures that the socket is on
the list with a valid non-NULL parent member.
Signed-off-by: Dean Jenkins <Dean_Jenkins@mentor.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Geliang Tang [Sat, 11 Mar 2017 00:46:58 +0000 (08:46 +0800)]
Bluetooth: bluecard: use setup_timer
Use setup_timer() instead of init_timer() to simplify the code.
Signed-off-by: Geliang Tang <geliangtang@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Luiz Augusto von Dentz [Sun, 12 Mar 2017 08:19:38 +0000 (10:19 +0200)]
6lowpan: Fix IID format for Bluetooth
According to RFC 7668 U/L bit shall not be used:
https://wiki.tools.ietf.org/html/rfc7668#section-3.2.2 [Page 10]:
In the figure, letter 'b' represents a bit from the
Bluetooth device address, copied as is without any changes on any
bit. This means that no bit in the IID indicates whether the
underlying Bluetooth device address is public or random.
|0 1|1 3|3 4|4 6|
|0 5|6 1|2 7|8 3|
+----------------+----------------+----------------+----------------+
|
bbbbbbbbbbbbbbbb|
bbbbbbbb11111111|
11111110bbbbbbbb|
bbbbbbbbbbbbbbbb|
+----------------+----------------+----------------+----------------+
Because of this the code cannot figure out the address type from the IP
address anymore thus it makes no sense to use peer_lookup_ba as it needs
the peer address type.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Reviewed-by: Stefan Schmidt <stefan@osg.samsung.com>
Acked-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Luiz Augusto von Dentz [Sun, 12 Mar 2017 08:19:37 +0000 (10:19 +0200)]
6lowpan: Use netdev addr_len to determine lladdr len
This allow technologies such as Bluetooth to use its native lladdr which
is eui48 instead of eui64 which was expected by functions like
lowpan_header_decompress and lowpan_header_compress.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Reviewed-by: Stefan Schmidt <stefan@osg.samsung.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Alexander Aring [Sun, 12 Mar 2017 08:19:36 +0000 (10:19 +0200)]
ipv6: addrconf: fix 48 bit 6lowpan autoconfiguration
This patch adds support for 48 bit 6LoWPAN address length
autoconfiguration which is the case for BTLE 6LoWPAN.
Signed-off-by: Alexander Aring <aar@pengutronix.de>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Reviewed-by: Stefan Schmidt <stefan@osg.samsung.com>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Alexander Aring [Sun, 12 Mar 2017 08:19:35 +0000 (10:19 +0200)]
6lowpan: iphc: override l2 packet information
The skb->pkt_type need to be set by L2, but on 6LoWPAN there exists L2
e.g. BTLE which doesn't has multicast addressing. If it's a multicast or
not is detected by IPHC headers multicast bit. The IPv6 layer will
evaluate this pkt_type, so we force set this type while uncompressing.
Should be okay for 802.15.4 as well.
Signed-off-by: Alexander Aring <aar@pengutronix.de>
Reviewed-by: Stefan Schmidt <stefan@osg.samsung.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Patrik Flykt [Sun, 12 Mar 2017 08:19:34 +0000 (10:19 +0200)]
6lowpan: Set MAC address length according to LOWPAN_LLTYPE
Set MAC address length according to the 6LoWPAN link layer in use.
Bluetooth Low Energy uses 48 bit addressing while IEEE802.15.4 uses
64 bits.
Signed-off-by: Patrik Flykt <patrik.flykt@linux.intel.com>
Reviewed-by: Stefan Schmidt <stefan@osg.samsung.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Patrik Flykt [Sun, 12 Mar 2017 08:19:33 +0000 (10:19 +0200)]
bluetooth: Set 6 byte device addresses
Set BTLE MAC addresses that are 6 bytes long and not 8 bytes
that are used in other places with 6lowpan.
Signed-off-by: Patrik Flykt <patrik.flykt@linux.intel.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Reviewed-by: Stefan Schmidt <stefan@osg.samsung.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
John Keeping [Wed, 15 Mar 2017 12:20:05 +0000 (12:20 +0000)]
Bluetooth: hci_bcm: Fix clock (un)prepare
The hci_bcm driver currently does not prepare/unprepare the clock and
goes directly to enable, but as the documentation for clk_enable says,
clk_prepare must be called before clk_enable.
Signed-off-by: John Keeping <john@metanate.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Elena Reshetova [Fri, 17 Mar 2017 11:12:46 +0000 (13:12 +0200)]
Bluetooth: convert rfcomm_dlc.refcnt from atomic_t to refcount_t
refcount_t type and corresponding API should be
used instead of atomic_t when the variable is used as
a reference counter. This allows to avoid accidental
refcounter overflows that might lead to use-after-free
situations.
Signed-off-by: Elena Reshetova <elena.reshetova@intel.com>
Signed-off-by: Hans Liljestrand <ishkamiel@gmail.com>
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: David Windsor <dwindsor@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Colin Ian King [Tue, 21 Mar 2017 12:20:28 +0000 (12:20 +0000)]
Bluetooth: btmrvl: fix spelling mistake: "unregester" -> "unregister"
trivial fix to spelling mistake in debug message
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Alexey Dobriyan [Mon, 10 Apr 2017 08:25:26 +0000 (11:25 +0300)]
net: make struct net_device::min_header_len 8-bit
This field is never big enough to warrant 16-bitness.
8-bit accesses enjoy shorted encoding on i386/x86_64 than 16-bit
accesses:
add/remove: 0/0 grow/shrink: 0/2 up/down: 0/-10 (-10)
function old new delta
loopback_setup 169 164 -5
ether_setup 148 143 -5
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Alexey Dobriyan [Mon, 10 Apr 2017 08:11:17 +0000 (11:11 +0300)]
net: neigh: make ->hh_len 32-bit
Using 16-bit ->hh_len doesn't save any memory, save some .text instead:
add/remove: 0/0 grow/shrink: 1/6 up/down: 2/-19 (-17)
function old new delta
neigh_update 2312 2314 +2
fwnet_header_cache 199 197 -2
eth_header_cache 101 99 -2
ip6_finish_output2 2371 2368 -3
vrf_finish_output6 1522 1518 -4
vrf_finish_output 1413 1409 -4
ip_finish_output2 1627 1623 -4
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ilan Tayari [Fri, 7 Apr 2017 23:07:08 +0000 (02:07 +0300)]
gso: Support frag_list splitting with head_frag
A driver may use build_skb() for received packets.
These SKBs then have a head_frag.
Since commit
d7e8883cfcf4 ("net: make GRO aware of
skb->head_frag"), GRO may build frag_list SKBs out of
head_frag received SKBs.
In such a case, the chained SKBs end up with a head_frag.
Commit
07b26c9454a2 ("gso: Support partial splitting at
the frag_list pointer") adds partial segmentation of frag_list
SKB chains into individual SKBs.
However, this is not done if the chained SKBs have any
linear part, because the device may not be able to DMA
the private linear buffer.
A chained frag_list SKB with head_frag is wrongfully
detected in this case as having a private linear part
and thus falls back to software GSO, while in fact the
linear part is backed by a DMA page just like any other frag.
This causes low performance when forwarding those packets
that were built with build_skb()
Allow partial segmentation at the frag_list pointer for
chained SKBs with head_frag.
Note that such SKBs can only be created by GRO, when applied
to received packets with head_frag.
Also note that this change only affects the data path that
performs the partial segmentation at frag_list pointer, and
not any of the other more common data paths.
Signed-off-by: Ilan Tayari <ilant@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Wed, 12 Apr 2017 14:44:03 +0000 (10:44 -0400)]
Merge branch 'l2tp-const'
Guillaume Nault says:
====================
l2tp: constify l2tp_session_get*() and l2tp_tunnel_find*()
Declare parameters of these functions as "const" where possible.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Guillaume Nault [Wed, 12 Apr 2017 08:05:30 +0000 (10:05 +0200)]
l2tp: define parameters of l2tp_tunnel_find*() as "const"
l2tp_tunnel_find() and l2tp_tunnel_find_nth() don't modify "net".
Signed-off-by: Guillaume Nault <g.nault@alphalink.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
Guillaume Nault [Wed, 12 Apr 2017 08:05:29 +0000 (10:05 +0200)]
l2tp: define parameters of l2tp_session_get*() as "const"
Make l2tp_pernet()'s parameter constant, so that l2tp_session_get*() can
declare their "net" variable as "const".
Also constify "ifname" in l2tp_session_get_by_ifname().
Signed-off-by: Guillaume Nault <g.nault@alphalink.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Wed, 12 Apr 2017 14:17:03 +0000 (10:17 -0400)]
Merge branch 'ftgmac100-rework-batch4-misc'
Benjamin Herrenschmidt says:
====================
ftgmac100: Rework batch 4 - Misc
This is v2 of the fourth batch of updates to the ftgmac100 driver.
This is a bunch of misc cleanups and fixes, such as properly
disabling HW checksum generation on AST2400 where it's known
to be broken and some chip init updates.
This also adds the ability to turn HW checksum on/off and
configure the ring sizes via ethtool.
v2 Fixes patch 1/10 (NETIF_F_HW_CSUM conversion)
The next (and last) batch will add a few more "features" such
as netpoll, multicast/promist, vlan offload...
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Benjamin Herrenschmidt [Wed, 12 Apr 2017 03:27:10 +0000 (13:27 +1000)]
ftgmac100: Set default ring sizes to 128 entries
I haven't seen any improvement above that size on the machines
I've tested with.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Benjamin Herrenschmidt [Wed, 12 Apr 2017 03:27:09 +0000 (13:27 +1000)]
ftgmac100: Make ring sizes configurable via ethtool
We set an arbitrary max at 1024 since we pre-allocate the actual
descriptor arrays and skb arrays to the full size to keep the
code a bit simpler and avoid allocation failures in the reset
task.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Benjamin Herrenschmidt [Wed, 12 Apr 2017 03:27:08 +0000 (13:27 +1000)]
ftgmac100: Add more register inits in ftgmac100_init_hw()
Clear stale interrupts on entry, configure FIFO sizes, set FIFO
thresholds, configure interrupt mitigation.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Benjamin Herrenschmidt [Wed, 12 Apr 2017 03:27:07 +0000 (13:27 +1000)]
ftgmac100: Open code remaining register writes
The helpers just take space but don't provide much value. Simple
one line comments are more explanatory.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Benjamin Herrenschmidt [Wed, 12 Apr 2017 03:27:06 +0000 (13:27 +1000)]
ftgmac100: Rename ftgmac100_setup_mac to ftgmac100_initial_mac
To remove more confusion. This function is about obtaining the
initial MAC address at driver probe time.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Benjamin Herrenschmidt [Wed, 12 Apr 2017 03:27:05 +0000 (13:27 +1000)]
ftgmac100: Rename ftgmac100_set_mac to ftgmac100_write_mac_addr
To avoid confusion with the ndo callback and generally be
clearer about the purpose of that function
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Benjamin Herrenschmidt [Wed, 12 Apr 2017 03:27:04 +0000 (13:27 +1000)]
ftgmac100: Set netdev->hw_features
So features can be turned on/off via ethtool
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Benjamin Herrenschmidt [Wed, 12 Apr 2017 03:27:03 +0000 (13:27 +1000)]
ftgmac100: Disable HW checksum generation on AST2400, enable on others
We found out that HW checksum generation only works from AST2500
onward. This disables it on AST2400 and removes the "no-hw-checksum"
properties in the device-trees. The problem we had wasn't related
to NC-SI.
Also rework the logic testing for that property so it can be used
to disable HW checksum generation and checking regardless of whether
NC-SI is used or not in case other variants out there need this.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Benjamin Herrenschmidt [Wed, 12 Apr 2017 03:27:02 +0000 (13:27 +1000)]
ftgmac100: Use device "compatible" property, not machine.
We test for aspeed chips to handle a couple of special cases,
but we do that by checking the machine type which isn't right.
Instead check the actual device compatible property. This also
updates the dtsi files for the aspeed SoC to match.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Benjamin Herrenschmidt [Wed, 12 Apr 2017 03:27:01 +0000 (13:27 +1000)]
ftgmac100: Upgrade to NETIF_F_HW_CSUM
The documentation describes NETIF_F_IP_CSUM as deprecated
so let's switch to NETIF_F_HW_CSUM and use the helper to
handle unhandled protocols.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Wed, 12 Apr 2017 03:01:15 +0000 (23:01 -0400)]
Merge branch 'net-smc-next'
Ursula Braun says:
====================
net/smc: patches for net-next
here are some patches for net/smc. Most important are
improvements for socket closing.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Ursula Braun [Mon, 10 Apr 2017 12:58:05 +0000 (14:58 +0200)]
net/smc: do not use IB_SEND_INLINE together with mapped data
smc specifies IB_SEND_INLINE for IB_WR_SEND ib_post_send calls, but
provides a mapped buffer to be sent. This is inconsistent, since
IB_SEND_INLINE works without mapped buffer. Problem has not been
detected in the past, because tests had been limited to Connect X3 cards
from Mellanox, whose mlx4 driver just ignored the IB_SEND_INLINE flag.
For now, the IB_SEND_INLINE flag is removed.
Signed-off-by: Ursula Braun <ubraun@linux.vnet.ibm.com>
Reviewed-by: Thomas Richter <tmricht@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ursula Braun [Mon, 10 Apr 2017 12:58:04 +0000 (14:58 +0200)]
net/smc: destruct non-accepted sockets
Make sure sockets never accepted are removed cleanly.
Signed-off-by: Ursula Braun <ubraun@linux.vnet.ibm.com>
Reviewed-by: Thomas Richter <tmricht@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ursula Braun [Mon, 10 Apr 2017 12:58:03 +0000 (14:58 +0200)]
net/smc: remove duplicate unhash
unhash is already called in sock_put_work. Remove the second call.
Signed-off-by: Ursula Braun <ubraun@linux.vnet.ibm.com>
Reviewed-by: Thomas Richter <tmricht@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ursula Braun [Mon, 10 Apr 2017 12:58:02 +0000 (14:58 +0200)]
net/smc: guarantee ConnClosed send after shutdown SHUT_WR
State SMC_CLOSED should be reached only, if ConnClosed has been sent to
the peer. If ConnClosed is received from the peer, a socket with
shutdown SHUT_WR done, switches errorneously to state SMC_CLOSED, which
means the peer socket is dangling. The local SMC socket is supposed to
switch to state APPFINCLOSEWAIT to make sure smc_close_final() is called
during socket close.
Signed-off-by: Ursula Braun <ubraun@linux.vnet.ibm.com>
Reviewed-by: Thomas Richter <tmricht@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ursula Braun [Mon, 10 Apr 2017 12:58:01 +0000 (14:58 +0200)]
net/smc: no socket state changes in tasklet context
Several state changes occur during SMC socket closing. Currently
state changes triggered locally occur in process context with
lock_sock() taken while state changes triggered by peer occur in
tasklet context with bh_lock_sock() taken. bh_lock_sock() does not
wait till a lock_sock(() task in process context is finished. This
may lead to races in socket state transitions resulting in dangling
SMC-sockets, or it may lead to duplicate SMC socket freeing.
This patch introduces a closing worker to run all state changes under
lock_sock().
Signed-off-by: Ursula Braun <ubraun@linux.vnet.ibm.com>
Reviewed-by: Thomas Richter <tmricht@linux.vnet.ibm.com>
Reported-by: Dave Jones <davej@codemonkey.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ursula Braun [Mon, 10 Apr 2017 12:58:00 +0000 (14:58 +0200)]
net/smc: always call the POLL_IN part of sk_wake_async
Wake up reading file descriptors for a closing socket as well, otherwise
some socket applications may stall.
Signed-off-by: Ursula Braun <ubraun@linux.vnet.ibm.com>
Reviewed-by: Thomas Richter <tmricht@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ursula Braun [Mon, 10 Apr 2017 12:57:59 +0000 (14:57 +0200)]
net/smc: guarantee reset of write_blocked for heavy workload
If peer indicates write_blocked, the cursor state of the received data
should be send to the peer immediately (in smc_tx_consumer_update()).
Afterwards the write_blocked indicator is cleared.
If there is no free slot for another write request, sending is postponed
to worker smc_tx_work, and the write_blocked indicator is not cleared.
Therefore another clearing check is needed in smc_tx_work().
Signed-off-by: Ursula Braun <ubraun@linux.vnet.ibm.com>
Reviewed-by: Thomas Richter <tmricht@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ursula Braun [Mon, 10 Apr 2017 12:57:58 +0000 (14:57 +0200)]
net/smc: return active RoCE port only
SMC requires an active ib port on the RoCE device.
smc_pnet_find_roce_resource() determines the matching RoCE device port
according to the configured PNET table. Do not return the found
RoCE device port, if it is not flagged active.
Signed-off-by: Ursula Braun <ubraun@linux.vnet.ibm.com>
Reviewed-by: Thomas Richter <tmricht@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ursula Braun [Mon, 10 Apr 2017 12:57:57 +0000 (14:57 +0200)]
net/smc: remove useless smc_ib_devices_list check
The global event handler is created only, if the ib_device has already
been used by at least one link group. It is guaranteed that there exists
the corresponding entry in the smc_ib_devices list. Get rid of this
superfluous check.
Signed-off-by: Ursula Braun <ubraun@linux.vnet.ibm.com>
Reviewed-by: Thomas Richter <tmricht@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ursula Braun [Mon, 10 Apr 2017 12:57:56 +0000 (14:57 +0200)]
net/smc: get rid of old comment
This patch removes an outdated comment.
Signed-off-by: Ursula Braun <ubraun@linux.vnet.ibm.com>
Reviewed-by: Thomas Richter <tmricht@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Joao Pinto [Mon, 10 Apr 2017 10:32:14 +0000 (11:32 +0100)]
net: stmmac: use netif_set_real_num_{rx,tx}_queues
In the submission of the lastest multiple buffer patch set, this fix was lost.
I am sending this patch to put it right again. The fix was originally proposed
by Arnd Bergmann.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Joao Pinto <jpinto@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Willem de Bruijn [Tue, 11 Apr 2017 18:08:08 +0000 (14:08 -0400)]
bpf: pass sk to helper functions
BPF helper functions access socket fields through skb->sk. This is not
set in ingress cgroup and socket filters. The association is only made
in skb_set_owner_r once the filter has accepted the packet. Sk is
available as socket lookup has taken place.
Temporarily set skb->sk to sk in these cases.
Signed-off-by: Willem de Bruijn <willemb@google.com>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Wei Yongjun [Tue, 11 Apr 2017 16:02:02 +0000 (16:02 +0000)]
devlink: fix return value check in devlink_dpipe_header_put()
Fix the return value check which testing the wrong variable
in devlink_dpipe_header_put().
Fixes: 1555d204e743 ("devlink: Support for pipeline debug (dpipe)")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Tue, 11 Apr 2017 18:51:36 +0000 (14:51 -0400)]
Merge branch 's390-qeth-updates'
Julian Wiedmann says:
====================
more s390/net updates
here's a second batch of s390/net patches for net-next.
A mixed bunch of qeth cleanups, and a few patches to add support for
ETHTOOL_GLINKSETTINGS.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Julian Wiedmann [Tue, 11 Apr 2017 14:11:19 +0000 (16:11 +0200)]
s390/qeth: remove unimplemented gdev routines
prepare() and complete() are not implemented by any discipline, so just
drop all the indirection.
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Reviewed-by: Hans Wippel <hwippel@linux.vnet.ibm.com>
Reviewed-by: Thomas Richter <tmricht@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Julian Wiedmann [Tue, 11 Apr 2017 14:11:18 +0000 (16:11 +0200)]
s390/qeth: use LINK_MODE_* to report the link characteristics
LINK_MODE_* replaces the u32-limited SUPPORTED_* / ENABLED_*
definitions.
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Reviewed-by: Thomas Richter <tmricht@linux.vnet.ibm.com>
Reviewed-by: Ursula Braun <ubraun@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Julian Wiedmann [Tue, 11 Apr 2017 14:11:17 +0000 (16:11 +0200)]
s390/qeth: convert to ETHTOOL_GLINKSETTINGS API
get_settings() is deprecated and lacks support for higher link
speeds, so implement get_link_ksettings() instead.
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Reviewed-by: Thomas Richter <tmricht@linux.vnet.ibm.com>
Reviewed-by: Ursula Braun <ubraun@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Julian Wiedmann [Tue, 11 Apr 2017 14:11:16 +0000 (16:11 +0200)]
s390/qeth: clean up qeth_set_ecmd_adv_sup()
In preparation for moving to get_link_ksettings(), clean up how
we build the supported and advertised port/speed masks.
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Reviewed-by: Thomas Richter <tmricht@linux.vnet.ibm.com>
Reviewed-by: Ursula Braun <ubraun@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Julian Wiedmann [Tue, 11 Apr 2017 14:11:15 +0000 (16:11 +0200)]
s390/qeth: use and remove some defines
1. a buffer has 16 is_header flags, because that's its # of elements
2. replace the last occurrence of QETH_HEADER_SIZE, and remove it
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Acked-by: Ursula Braun <ubraun@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Julian Wiedmann [Tue, 11 Apr 2017 14:11:14 +0000 (16:11 +0200)]
s390/qeth: use correct return type for hard_start_xmit()
ndo_start_xmit() expects us to return netdev_tx_t here...
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Acked-by: Ursula Braun <ubraun@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Julian Wiedmann [Tue, 11 Apr 2017 14:11:13 +0000 (16:11 +0200)]
s390/qeth: remove unused parameter
'elements_needed' is not used in qeth_do_send_packet_fast(),
so consequently remove it.
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Acked-by: Ursula Braun <ubraun@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Julian Wiedmann [Tue, 11 Apr 2017 14:11:12 +0000 (16:11 +0200)]
s390/qeth: move gdev shutdown handler to core
Duplicated code.
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Acked-by: Ursula Braun <ubraun@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Julian Wiedmann [Tue, 11 Apr 2017 14:11:11 +0000 (16:11 +0200)]
s390/qeth: move NAPI poll routine to core
Identical code, we just need to call a layer-specific hook
to process any received buffer.
qeth_buffer_reclaim_work() is shuffled around to avoid a
forward declaration for qeth_queue_input_buffer().
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Acked-by: Ursula Braun <ubraun@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Julian Wiedmann [Tue, 11 Apr 2017 14:11:10 +0000 (16:11 +0200)]
s390/qeth: move common ioctl handling to core
There's a number of layer-independent ioctls that we can handle
in core, and reduce code duplication. For layer-specific ioctls,
add a do_ioctl() discipline hook.
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Acked-by: Ursula Braun <ubraun@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Johannes Berg [Tue, 11 Apr 2017 13:34:58 +0000 (15:34 +0200)]
bpf: remove struct bpf_map_type_list
There's no need to have struct bpf_map_type_list since
it just contains a list_head, the type, and the ops
pointer. Since the types are densely packed and not
actually dynamically registered, it's much easier and
smaller to have an array of type->ops pointer. Also
initialize this array statically to remove code needed
to initialize it.
In order to save duplicating the list, move it to the
types header file added by the previous patch and
include it in the same fashion.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
projects / openwrt / staging / blogic.git / log