Jason A. Donenfeld [Wed, 27 Feb 2019 23:36:49 +0000 (00:36 +0100)]
wireguard: bump to 0.0.
20190227
* wg-quick: freebsd: allow loopback to work
FreeBSD adds a route for point-to-point destination addresses. We don't
really want to specify any destination address, but unfortunately we
have to. Before we tried to cheat by giving our own address as the
destination, but this had the unfortunate effect of preventing
loopback from working on our local ip address. We work around this with
yet another kludge: we set the destination address to 127.0.0.1. Since
127.0.0.1 is already assigned to an interface, this has the same effect
of not specifying a destination address, and therefore we accomplish the
intended behavior. Note that the bad behavior is still present in Darwin,
where such workaround does not exist.
* tools: remove unused check phony declaration
* highlighter: when subtracting char, cast to unsigned
* chacha20: name enums
* tools: fight compiler slightly harder
* tools: c_acc doesn't need to be initialized
* queueing: more reasonable allocator function convention
Usual nits.
* systemd: wg-quick should depend on nss-lookup.target
Since wg-quick(8) calls wg(8) which does hostname lookups, we should
probably only run this after we're allowed to look up hostnames.
* compat: backport ALIGN_DOWN
* noise: whiten the nanoseconds portion of the timestamp
This mitigates unrelated sidechannel attacks that think they can turn
WireGuard into a useful time oracle.
* hashtables: decouple hashtable allocations from the main device allocation
The hashtable allocations are quite large, and cause the device allocation in
the net framework to stall sometimes while it tries to find a contiguous
region that can fit the device struct. To fix the allocation stalls, decouple
the hashtable allocations from the device allocation and allocate the
hashtables with kvmalloc's implicit __GFP_NORETRY so that the allocations fall
back to vmalloc with little resistance.
* chacha20poly1305: permit unaligned strides on certain platforms
The map allocations required to fix this are mostly slower than unaligned
paths.
* noise: store clamped key instead of raw key
This causes `wg show` to now show the right thing. Useful for doing
comparisons.
* compat: ipv6_stub is sometimes null
On ancient kernels, ipv6_stub is sometimes null in cases where IPv6 has
been disabled with a command line flag or other failures.
* Makefile: don't duplicate code in install and modules-install
* Makefile: make the depmod path configurable
* queueing: net-next has changed signature of skb_probe_transport_header
A 5.1 change. This could change again, but for now it allows us to keep this
snapshot aligned with our upstream submissions.
* netlink: don't remove allowed ips for new peers
* peer: only synchronize_rcu_bh and traverse trie once when removing all peers
* allowedips: maintain per-peer list of allowedips
This is a rather big and important change that makes it much much faster to do
operations involving thousands of peers. Batch peer/allowedip addition and
clearing is several orders of magnitude faster now.
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Alexander Couzens [Wed, 12 Dec 2018 15:10:42 +0000 (16:10 +0100)]
tools: migrate from squashfs4 to squashfskit4
squashfskit is a fork of the squashfs-tools.
squashfskit creates reproducible filesystems and includes
many of the distro patches.
Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
Tested-by: Paul Spooren <mail@aparcar.org>
Eneas U de Queiroz [Wed, 27 Feb 2019 21:06:44 +0000 (18:06 -0300)]
openssl: bump to release 1.1.1b
This is bugfix release that incorporated all of the devcrypto engine
patches currently in the tree.
The cleaning procedure in Package/Configure was not removing the
dependency files, causing linking errors during a rebuild with
different options. It was replaced by a simple make clean.
Signed-off-by: Eneas U de Queiroz <cote2004-github@yahoo.com>
Hans Dedecker [Wed, 27 Feb 2019 11:10:20 +0000 (12:10 +0100)]
odhcpd: update to latest git HEAD
16c5b6c ubus: always trigger an update if interface is not found
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
David Santamaría Rogado [Tue, 26 Feb 2019 23:14:17 +0000 (00:14 +0100)]
omcproxy: define configuration file
omcproxy's configuration is lost on every update or installation.
Avoid it by defining the configuration file.
Signed-off-by: David Santamaría Rogado <howl.nsp@gmail.com>
Mantas Pucka [Mon, 25 Feb 2019 16:29:13 +0000 (18:29 +0200)]
Revert "iw: compile with LTO enabled"
After update to 5.0.1 iw-full package failed to display command list on
ipq40xx arch. Root cause was found to be LTO reordering causing
incorrect detection of command struct size in:
iw.c:552
cmd_size = labs((long)&__section_set - (long)&__section_get);
This reverts commit
ef16a394d2b24a363b50b5b4720cb23fe156c9da.
Signed-off-by: Mantas Pucka <mantas@8devices.com>
Hauke Mehrtens [Tue, 26 Feb 2019 20:12:18 +0000 (21:12 +0100)]
strace: update to version 2.26
The new patch is a backport from current strace master.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Syrone Wong [Sun, 16 Dec 2018 10:44:43 +0000 (18:44 +0800)]
tools/isl: update to 0.20
Signed-off-by: Syrone Wong <wong.syrone@gmail.com>
Daniel Engberg [Sat, 9 Feb 2019 01:22:02 +0000 (01:22 +0000)]
toolchain/binutils: Add binutils 2.32
Add binutils 2.32 to repo
Signed-off-by: Daniel Engberg <daniel.engberg.lists@pyret.net>
Daniel Engberg [Sat, 23 Feb 2019 01:45:42 +0000 (01:45 +0000)]
toolchain: Update to GCC 8.3.0
Update GCC to 8.3.0
Refresh patches
Allow GCC to be used for ARC
Source: https://github.com/openwrt/openwrt/pull/1803#issuecomment-
462334890
Signed-off-by: Daniel Engberg <daniel.engberg.lists@pyret.net>
Daniel Engberg [Sat, 23 Feb 2019 09:47:54 +0000 (10:47 +0100)]
toolchain/gcc: Remove workaround for GCC 4.8
GCC 4.8 was removed a long time ago...
Signed-off-by: Daniel Engberg <daniel.engberg.lists@pyret.net>
Daniel Engberg [Sun, 24 Feb 2019 07:08:14 +0000 (08:08 +0100)]
popt: Use modern toolchain logic
Replace define Build/Configure with CONFIGURE_ARGS
Signed-off-by: Daniel Engberg <daniel.engberg.lists@pyret.net>
Matt Merhar [Tue, 26 Feb 2019 13:05:07 +0000 (08:05 -0500)]
elfutils: fix install .so glob
Only libelf was being packaged correctly - libdw and libasm included
just the symlinks.
Signed-off-by: Matt Merhar <mattmerhar@protonmail.com>
Aleksander Jan Bajkowski [Wed, 20 Feb 2019 13:17:45 +0000 (14:17 +0100)]
sunxi: add support for Orange Pi One
CPU: H3 Quad-core Cortex-A7 H.265/HEVC 4K @ 1.2 Ghz
GPU: Mali400MP2 GPU @ 600MHz (supports OpenGL ES 2.0)
Memory: 512MB DDR3 (shared with GPU)
Onboard: Storage TF card (Max. 64GB) / MMC card slot
Onboard header: SPI, I2C, GPIO, UART
USB 2.0: One USB 2.0 HOST, One USB 2.0 OTG
Signed-off-by: Aleksander Jan Bajkowski <A.Bajkowski@stud.elka.pw.edu.pl>
David Bauer [Fri, 22 Feb 2019 23:25:07 +0000 (00:25 +0100)]
ath79: fix support-list for TP-Link WDR3600
The TP-Link WDR3600 shares the same machine-code in the ar71xx target,
thus expecting "tl-wdr4300" not "tl-wdr3600" in the support-list
metadata to allow non-forced sysupgrades from ar71xx to ath79.
With this, it is possible to flash a WDR4300 image on the WDR3600. It
is no problem however, as the only difference is the 5GHz WiFi chip
which has 3SS instead of 2SS. Both work with either image.
Signed-off-by: David Bauer <mail@david-bauer.net>
David Bauer [Sat, 23 Feb 2019 12:12:49 +0000 (13:12 +0100)]
ath79: add ar71xx support-list entry for Fritz4020
This adds the support-list entry the AVM FRITZ!Box 4020 expects in the
ar71xx target to allow non-forced sysupgrades from ar71xx to ath79.
Signed-off-by: David Bauer <mail@david-bauer.net>
Andreas Ziegler [Mon, 25 Feb 2019 00:19:59 +0000 (01:19 +0100)]
ar71xx: GL.iNet AR300M family: correct LED definitions
remove USB as this is no LED but power control
rename WiFi LED with correct color red (like in stock firmware)
set middle LED to be used for LAN link/activity
Signed-off-by: Andreas Ziegler <dev@andreas-ziegler.de>
Sven Eckelmann [Mon, 25 Feb 2019 19:42:28 +0000 (20:42 +0100)]
ath10k-ct: fix incorrect multicast/broadcast rate setting
If no mcast_rate is set for the wifi-iface then there is no rate_idx (0)
set for the bss. This can break for example 5GHz meshpoint interfaces
because 0 maps to a CCK rate (11Mbit/s).
It must also be avoided that the ath10k-ct internal state for the rates is
not synced with the mac80211 rates state. Otherwise, the user specified
rate (e.g. a wifi-iface mcast_rate for a meshpoint interface) will only be
set on startup. And a short while after that, ath10k-ct specific code in
ath10k_check_apply_special_rates is missing a valid rate in its own
structures and is then recalculating a new default rate. This default rate
is in most situations not the requested rate.
Fixes: 4df3c71cd4c5 ("ath10k-ct: Update to 2018-12-11 and use version based on 4.19")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Sven Eckelmann [Mon, 25 Feb 2019 19:42:28 +0000 (20:42 +0100)]
mac80211: ath10k: fix incorrect multicast/broadcast rate setting
If no mcast_rate is set for the wifi-iface then there is no rate_idx (0)
set for the bss. This breaks for example 5GHz meshpoint interfaces because
0 maps to a CCK rate (11Mbit/s).
Fixes: db90c243a0b9 ("mac80211: update to version based on 4.19-rc4")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Hauke Mehrtens [Tue, 26 Feb 2019 19:41:03 +0000 (20:41 +0100)]
mac80211: Add WDS / 4addr fix for ath10k supported devices
This should fix the WDS / 4addr mode with ath10k and probably other
devices.
This patch was found here: https://patchwork.kernel.org/patch/
10692383/
Fixes: d9eefa7a7031 ("mac80211: rebase ontop of v4.18.5")
Reported-by: Signed-off-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Stanislaw Gruszka [Sun, 24 Feb 2019 09:23:18 +0000 (10:23 +0100)]
mac80211: rt2x00: fix crash on release_firmware
Fix crash due to passing invalid r2x00dev->eeprom_file pointer to
release_firmware(). Since we copy eeprom data with EEPROM_SIZE
in rt2800_read_eeprom() we can use eeprom_file->size as marker
if the file was crated by request_firmware().
Acked-by: Kristian Evensen <kristian.evensen@gmail.com>
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Felix Fietkau [Tue, 26 Feb 2019 17:00:38 +0000 (18:00 +0100)]
mt76: update to the latest version
28d81ff mt76x0: eeprom: fix VHT mcs{8,9} rate power offset
6e33ce6 mt76: move mt76_mcu_msg_alloc in mt76-core
4637f95 mt76: move mt76_mcu_get_response in mt76-core
1763cb0 mt76: move mt76_mcu_rx_event in mt76-core
4db9d75 mt76x0: mcu: remove useless commented configuration
91d0455 mt76: move mt76_dma_tx_queue_skb_raw in mt76-core module
0e8e53f mt76: remove add_buf pointer in mt76_queue_ops
db47920 mt7603: rely on mt76_mcu_msg_alloc routine
471c447 mt7603: rely on mt76_mcu_get_response routine
cacc986 mt7603: rely on mt76_mcu_rx_event routine
11ab620 mt7603: rely on mt76_tx_queue_skb_raw common routine
82fa312 mt7603: move alloc_dev common code in mt76_alloc_device
47d5922 mt76: move alloc_device common code in mt76_alloc_device
c50c993 mt76x2u: remove mt76x2u_alloc_device routine
6ed5b7a mt76x0: remove mt76x0u_alloc_device routine
e32e249 mt76x2: remove mt76x2_alloc_device routine
6aacd1e mt76: change the return type of mt76_dma_attach()
a10e9e5 mt76x02u: use usb_bulk_msg to upload firmware
a774ff6 mt76: usb: fix possible NULL pointer dereference in mt76u_mcu_deinit
c2877bc mt76: usb: fix possible memory leak in mt76u_buf_free
a5cfe96 mt76: usb: do not run mt76u_queues_deinit twice
1e4db14 mt76: usb: move mt76u_check_sg in usb.c
302406b mt76: usb: do not use sg buffers for mcu messages
8ab5267 mt76: usb: use a linear buffer for tx/rx datapath if sg is not supported
a0a3505 mt76: usb: introduce disable_usb_sg parameter
0cee180 mt76: usb: use dev_err_ratelimited instead of dev_err in mt76u_complete_rx
1bb97c4 mt76x02u: remove bogus check and comment padding
2cbc2d4 mt76: Use the correct hweight8() function
f18e03a mt76x0u: fix suspend/resume
6231336 mt76: mt76x02: fix TSF sync mode
783da04 mt76: mt76x02: fix beacon timer drift adjustment
43d2507 mt76: mt76x02: fix beacon timer issue
59a6587 mt76: mt76x02: only reset beacon drift counter when enabling beacons
8c8eb98 mt76: mt76x02: issue watchdog reset on MCU request timeout
52161d2 mt76: mt76x02: fix ED/CCA enabling/disabling
5e7ecce mt76: mt76x2: unify mt76x2[u]_mac_resume
18af219 mt76: mt76x02: set MT_TXOP_HLDR_TX40M_BLK_EN for mt76x2
e5747b2 mt76usb: allow mt76u_bulk_msg be used for reads
2437a9a mt76usb: use synchronous msg for mcu command responses
e4250c9 mt76usb: remove usb_mcu.c
8b1110e mt76: usb: fix warning in mt76u_buf_free
89215f6 mt76: usb: introduce mt76u_fill_bulk_urb routine
523e374 mt76: usb: simplify rx buffer allocation
ffe1292 mt76: usb: simplify mt76u_tx_build_sg routine
e2a9d40 mt7603: fix ba window size selection
b040ef7 mt76: remove no longer used routine declarations
645ef43 mt76: usb: check urb->num_sgs limit in mt76u_process_rx_entry
fd315bd mt7603: disable dynamic sensitivity adjustment by default
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Piotr Dymacz [Tue, 26 Feb 2019 12:04:54 +0000 (13:04 +0100)]
build: qsdk-ipq-*: include dtc in PATH before calling mkimage
Use 'dtc' from kernel sources instead of relying on host tool.
Fixes: bf4630e5adb4 ("build: add helpers for generating QSDK sysupgrade compatible images")
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
Piotr Dymacz [Tue, 29 Jan 2019 17:12:51 +0000 (18:12 +0100)]
uboot-envtools: add support for ALFA Network AP120C-AC
While at it, fix alphabetical order.
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
Piotr Dymacz [Tue, 29 Jan 2019 17:12:51 +0000 (18:12 +0100)]
ipq40xx: add support for ALFA Network AP120C-AC
ALFA Network AP120C-AC is a dual-band ceiling AP, based on Qualcomm
IPQ4018 + QCA8075 platform.
Specification:
- Qualcomm IPQ4018 (717 MHz)
- 256 MB of RAM (DDR3)
- 16 MB (SPI NOR) + 128 MB (SPI NAND) of flash
- 2x Gbps Ethernet, with 802.3af PoE support in one port
- 2T2R 2.4/5 GHz (IPQ4018), with ext. FEMs (QFE1952, QFE1922)
- 3x U.FL connectors
- 1x 1.8 dBi (Bluetooth) and 2x 3/5 dBi dual-band (Wi-Fi) antennas
- Atmel/Microchip AT97SC3205T TPM module (I2C bus)
- TI CC2540 Bluetooth LE module (USB 2.0 bus)
- 4x LED (all driven by GPIO)
- 1x button (reset)
- 1x USB 2.0 (optional, not installed in indoor version)
- DC jack for main power input (12 V)
- UART header available on PCB (2.0 mm pitch)
Flash instruction:
1. This board uses dual-image feature (128 MB NAND is divided into two
64 MB partitions: 'rootfs1' and 'rootfs2').
2. Before update, make sure your device is running firmware no older
than v1.1 (previous versions have incompatible U-Boot).
3. Use 'factory' image in vendor GUI or for sysupgrade tool, without
preserving settings.
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
Piotr Dymacz [Tue, 29 Jan 2019 17:12:51 +0000 (18:12 +0100)]
ipq-wifi: add board-2.bin for ALFA Network AP120C-AC
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
Piotr Dymacz [Tue, 29 Jan 2019 17:12:51 +0000 (18:12 +0100)]
ipq40xx: add support for Macronix MX35LF1GE4AB SPI NAND
Without a proper SPI NAND support (SPI NAND framework is available in
kernel >= 4.19) the only way to make such flash working is to include
it in raw/parallel NAND subsystem support and combine with mt29f staging
driver. Obviously, this approach isn't going to be accepted by upstream
(similar support for Winbond W25N01GV was rejected).
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
Piotr Dymacz [Tue, 29 Jan 2019 17:12:51 +0000 (18:12 +0100)]
build: add helpers for generating QSDK sysupgrade compatible images
Qualcomm SDK (QSDK) sysupgrade compatible images for IPQ40xx, IPQ806x
and IPQ807x use FIT format together with 'dumpimage' tool from U-Boot
for verifying and extracting them. Based on 'images' sections names,
corresponding mtd partitions are flashed. For example, in case of
NOR-only boards, below mapping is used (section name -> mtd name):
hlos* -> 0:HLOS
rootfs* -> rootfs
And for boards with NAND (kernel inside UBI):
ubi* -> rootfs
Above mappings come from unmodified QSDK sources and might be wrong for
boards running custom or modified QSDK-based firmware. Some of vendors
adjust them to meet their modified mtd layout or features like recovery
or dual-image support.
This adds simple script 'mkits-qsdk-ipq-image.sh' (based on 'mkits.sh')
for generating FIT images tree source files, compatible with the QSDK
sysupgrade format. Resulting images can be used for initial (factory ->
OpenWrt) installation and would work both in CLI and GUI.
The script is universal in a way it allows to include as many sections
as needed. To make use of it, two generic/basic build recipes for NOR
and NAND based boards are also included in 'image-commands.mk':
Build/qsdk-ipq-factory-nand
Build/qsdk-ipq-factory-nor
Example usage for board with UBI in NAND:
IMAGE/nand-factory.bin := append-ubi | qsdk-ipq-factory-nand
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
Koen Vandeputte [Mon, 25 Feb 2019 10:38:50 +0000 (11:38 +0100)]
kernel: bump 4.19 to 4.19.25
Refreshed all patches.
Compile-tested on: cns3xxx
Runtime-tested on: cns3xxx
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Koen Vandeputte [Mon, 25 Feb 2019 10:38:23 +0000 (11:38 +0100)]
kernel: bump 4.14 to 4.14.103
Refreshed all patches.
Compile-tested on: ar71xx, cns3xxx, imx6, x86_64
Runtime-tested on: ar71xx, cns3xxx, imx6
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Koen Vandeputte [Mon, 25 Feb 2019 10:37:51 +0000 (11:37 +0100)]
kernel: bump 4.9 to 4.9.160
Refreshed all patches.
Compile-tested on: ar7
Runtime-tested on: none
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Koen Vandeputte [Mon, 25 Feb 2019 10:33:35 +0000 (11:33 +0100)]
kernel: bump 3.18 to 3.18.136
Refreshed all patches.
Fixes:
- CVE-2019-6974
Compile-tested: adm5120
Runtime-tested: none
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Stijn Tintel [Mon, 25 Feb 2019 13:46:10 +0000 (15:46 +0200)]
kernel: add missing config symbols
The addition of kmod-input-touchscreen-ads7846 enabled
INPUT_TOUCHSCREEN, which exposes several other symbols on various
targets. Add those symbols to the generic kernel configs to fix build.
Fixes: 77a54bbf13bf ("kernel: add kmod-input-touchscreen-ads7846")
Reported-by: Hannu Nyman <hannu.nyman@iki.fi>
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Hans Dedecker [Mon, 25 Feb 2019 11:00:08 +0000 (12:00 +0100)]
odhcpd: update to latest git HEAD (FS#2142)
9e9389c dhcpv4: fix adding assignment in list (FS#2142)
e69265b dhcpv4: fix static lease lookup
afbd7dd dhcp: rework assignment free logic
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
Stijn Tintel [Sun, 24 Feb 2019 22:49:39 +0000 (00:49 +0200)]
kernel: fix kmod-input-touchscreen-ads7846 deps
On targets that don't have input support enabled in the kernel config,
building kmod-input-touchscreen-ads7846 fails due to a missing
dependency on kmod-input-core. Add the dependency to fix this.
Fixes: 77a54bbf13bf ("kernel: add kmod-input-touchscreen-ads7846")
Reported-by: Hannu Nyman <hannu.nyman@iki.fi>
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Alexander Couzens [Wed, 20 Feb 2019 17:09:50 +0000 (18:09 +0100)]
package/dnsmasq: add max_ttl/min_cache_ttl/max_cache_ttl
max_ttl - limit the ttl in the dns answer if greater as $max_ttl
min_cache_ttl - force caching of dns answers even the ttl in the answer
is lower than the $min_cache_ttl
max_cache_ttl - cache only dns answer for $max_cache_ttl.
Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
Stijn Tintel [Wed, 13 Feb 2019 10:51:27 +0000 (12:51 +0200)]
kernel: add kmod-input-touchscreen-ads7846
This module adds support for ADS7846 based touchscreens used in devices
like the WaveShare 3.5" and 4" LCD displays designed for Raspberry Pi.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Stijn Tintel [Sat, 9 Feb 2019 17:01:28 +0000 (19:01 +0200)]
kernel: add kmod-fb-tft-ili9486
This module adds support for the ILI9486 LCD controller used in devices
like the Waveshare 3.5" and 4" LCD displays designed for Raspberry Pi.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Stijn Tintel [Sat, 9 Feb 2019 16:31:48 +0000 (18:31 +0200)]
kernel: add kmod-fb-tft
This module adds support for small TFT LCD display modules. While this
module also exists in the 4.9 kernel, we are not going to support this
kernel in the next major release, so don't make it available for 4.9.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Stijn Tintel [Sat, 9 Feb 2019 16:10:26 +0000 (18:10 +0200)]
kernel: add kmod-fb-sys-ram
The kernel modules that provide support for framebuffers in system RAM
are currently included in the kmod-drm-imx package. Move them to a
separate package, so that other modules can depend on them.
Increase the autoload order of the drm-imx* packages to load the modules
after loading the fb modules they depend on.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Stijn Tintel [Tue, 5 Feb 2019 00:25:22 +0000 (02:25 +0200)]
kernel: add kmod-iio-ccs811
This module supports the AMS CCS811 VOC sensor.
Tested on Raspberry Pi Zero W and ODROID C2.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Yousong Zhou [Wed, 20 Feb 2019 06:58:51 +0000 (06:58 +0000)]
dnsmasq: prefer localuse over resolvfile guesswork
This makes it clear that localuse when explicitly specified in the
config will have its final say on whether or not the initscript should
touch /etc/resolv.conf, no matter whatever the result of previous
guesswork would be
Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
Koen Vandeputte [Wed, 20 Feb 2019 15:02:57 +0000 (16:02 +0100)]
kernel: bump 4.19 to 4.19.24
Refreshed all patches.
Compile-tested on: cns3xxx
Runtime-tested on: cns3xxx
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Koen Vandeputte [Wed, 20 Feb 2019 15:02:26 +0000 (16:02 +0100)]
kernel: bump 4.14 to 4.14.102
Refreshed all patches.
Remove upstreamed:
- 272-uapi-if_ether.h-prevent-redefinition-of-struct-ethhd.patch
Remove upstreamed hunks:
- 080-pinctrl-msm-fix-gpio-hog-related-boot-issues.patch
Fixes:
- CVE-2018-
1000026
Compile-tested on: ar71xx, cns3xxx, imx6, x86_64
Runtime-tested on: ar71xx, cns3xxx, imx6
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Koen Vandeputte [Wed, 20 Feb 2019 15:01:10 +0000 (16:01 +0100)]
kernel: bump 4.9 to 4.9.159
Refreshed all patches.
Remove upstreamed:
- 023-1-smsc95xx-Use-skb_cow_head-to-deal-with-cloned-skbs.patch
- 023-6-ch9200-use-skb_cow_head-to-deal-with-cloned-skbs.patch
- 023-7-kaweth-use-skb_cow_head-to-deal-with-cloned-skbs.patch
- 050-usb-dwc2-Remove-unnecessary-kfree.patch
- 092-netfilter-nf_tables-fix-mismatch-in-big-endian-syste.patch
- 272-uapi-if_ether.h-prevent-redefinition-of-struct-ethhd.patch
Fixes:
- CVE-2018-
1000026
Compile-tested on: ar7
Runtime-tested on: none
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Koen Vandeputte [Wed, 20 Feb 2019 14:47:25 +0000 (15:47 +0100)]
kernel: bump 3.18 to 3.18.135
Refreshed all patches.
Fixes:
- CVE-2019-3819
- CVE-2019-7221
- CVE-2019-7222
Compile-tested on: adm5120
Runtime-tested on: none
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Yousong Zhou [Tue, 19 Feb 2019 06:31:54 +0000 (06:31 +0000)]
scripts/qemustart: allow machine selection with new option --machine
This can be used to set machine options like highmem=off for running old
armvirt/32 kernel lacking LPAE support with QEMU version 3.0 or later
[1] Armv7 guest fails to boot with qemu-3.0.0-1,
https://bugzilla.redhat.com/show_bug.cgi?id=
1633328#c5
Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
Rafał Miłecki [Wed, 20 Feb 2019 22:05:48 +0000 (23:05 +0100)]
mac80211: backport more brcmfmac changes queued for the 5.1
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Oever González [Wed, 20 Feb 2019 16:47:06 +0000 (10:47 -0600)]
ipq-wifi: update ipq-wifi for Linksys EA6350v3
This commit updates the file "board-linksys_ea6359v3".
Without this commit, the Linksys EA6350v3 will experience poor wireless
performance in both bands. With this patch, wireless performace will be
comparable to the performance of the stock firmware.
Signed-off-by: Oever González <notengobattery@gmail.com>
Chuanhong Guo [Tue, 19 Feb 2019 06:27:08 +0000 (14:27 +0800)]
ath79: fix wmac memory region for qca953x
According to /arch/mips/include/asm/mach-ath79/ar71xx_regs.h
the size of wmac register range for qca953x is only 0x20000.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
Christian Lamparter [Sun, 17 Feb 2019 17:11:59 +0000 (18:11 +0100)]
firmware: ipq-wifi: mark packages as nonshared
The board-files are specific to the target and device. Hence
they need to be set as nonshared. Otherwise they do not show
up on the package repository. This causes problems for
imagebuilder, if it needs to build a image for a specific
device that hasn't had the time to have get its boardfile
upstream.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Linus Walleij [Fri, 15 Feb 2019 16:02:23 +0000 (17:02 +0100)]
gemini: Generate harddisk image for DNS-313
This makes OpenWrt build an Ext2+Ext4 partitioned image
for the D-Link DNS-313 with two blank partitions, a boot
partition on /dev/sda3 and a rootfs partition on
/dev/sda4.
This uses the methods already used in apm821xx including
the tricks to convert the generated Ext2 filesystem
partition to version 1 so that the firmware bootloader
will properly recognize it.
We patch a bit around the build files to make sure we
get the rootfs size set and that genext2fs is properly
built.
Tested on the D-Link DNS-313.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
[Fixing and tricksing]
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Linus Walleij [Fri, 15 Feb 2019 16:02:14 +0000 (17:02 +0100)]
firmware-tools/ptgen: Allow generation 0 size partitions
The firmware on the D-Link DNS-313 NAS require two blank
partitions before the boot partition. Support this if
explicitly requested with a "-n" flag.
Tested on the D-Link DNS-313.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
[Broken out from original patch]
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Christian Lamparter [Thu, 14 Feb 2019 18:06:47 +0000 (19:06 +0100)]
ipq40xx: speed up ath10k-caldata extraction
Reading and writing to and from flash storage is slow and currently,
the ath10kcal_extract() scripts are even more at an disadvantage
because they use a block size of 1 to be able skip.
This patch reworks the extraction scripts to be much faster and
efficient by reading and writing the calibration data in possibly
one big block.
before: (Tested on a RT-AC58U, which has SPI-NAND).
# time dd if=/dev/ubi0_1 of=/lib/firmware/... bs=1 skip=4096 count=12064
12064+0 records in
12064+0 records out
real 0m 0.28s
user 0m 0.02s
sys 0m 0.24s
after:
# time dd if=/dev/ubi0_1 of=/lib/firmware/... bs=12064 skip=4096 count=1 iflag=skip_bytes
1+0 records in
1+0 records out
real 0m 0.01s
user 0m 0.00s
sys 0m 0.00s
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Daniel Golle [Wed, 20 Feb 2019 14:12:44 +0000 (15:12 +0100)]
uqmi: fix PIN_STATUS_FAILED error with MC7455 WCDMA/LTE modem
Apparently this modem replies differently to attempted --get-pin-status
which makes the script fail if a pincode is set. Fix this.
Manufacturer: Sierra Wireless, Incorporated
Model: MC7455
Revision: SWI9X30C_02.24.05.06 r7040 CARMD-EV-FRMWR2 2017/05/19 06:23:09
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Arnout Vandecappelle (Essensium/Mind) [Mon, 10 Dec 2018 16:02:27 +0000 (17:02 +0100)]
hostapd: add Multi-AP patches and config options
Cherry-pick Multi-AP commits from uptream:
9c06f0f6a hostapd: Add Multi-AP protocol support
5abc7823b wpa_supplicant: Add Multi-AP backhaul STA support
a1debd338 tests: Refactor test_multi_ap
bfcdac1c8 Multi-AP: Don't reject backhaul STA on fronthaul BSS
cb3c156e7 tests: Update multi_ap_fronthaul_on_ap to match implementation
56a2d788f WPS: Add multi_ap_subelem to wps_build_wfa_ext()
83ebf5586 wpa_supplicant: Support Multi-AP backhaul STA onboarding with WPS
66819b07b hostapd: Support Multi-AP backhaul STA onboarding with WPS
8682f384c hostapd: Add README-MULTI-AP
b1daf498a tests: Multi-AP WPS provisioning
Add support for Multi-AP to the UCI configuration. Every wifi-iface gets
an option 'multi_ap'. For APs, its value can be 0 (multi-AP support
disabled), 1 (backhaul AP), 2 (fronthaul AP), or 3 (fronthaul + backhaul
AP). For STAs, it can be 0 (not a backhaul STA) or 1 (backhaul STA, can
only associate with backhaul AP).
Also add new optional parameter to wps_start ubus call of
wpa_supplicant to indicate that a Multi-AP backhaul link is required.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Signed-off-by: Arnout Vandecappelle (Essensium/Mind) <arnout@mind.be>
Daniel Golle [Tue, 19 Feb 2019 17:30:24 +0000 (18:30 +0100)]
mac80211: rt2x00: replace pending by merged patches
Those have by now been merged into wireless-drivers-next:
17ae2acd1a6f rt2x00: remove unneeded check
5991a2ecd070 rt2x00: remove confusing AGC register
9ad3b5565445 rt2800: enable TX_PIN_CFG_LNA_PE_ bits per band
7aca14885ede rt2800: enable TX_PIN_CFG_RFRX_EN only for MT7620
c7ff1bfeaf1c rt2800: comment and simplify AGC init for RT6352
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Hauke Mehrtens [Tue, 19 Feb 2019 22:03:15 +0000 (23:03 +0100)]
x86: Make kmod-drm-radeon and kmod-drm-amdgpu depend on x86
Currently these kernel packages only work on x86, restrict them to that
target.
Fixes: 2f239c02a031 ("x86: video: add amdgpu DRM kernel package")
Fixes: 2f6918ee9be9 ("x86: video: add radeon DRM module support")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Pawel Dembicki [Mon, 18 Feb 2019 20:49:53 +0000 (20:49 +0000)]
generic: kernel: Add missing config option
DRM packages break modules compilation for sunxi target,
cortexa7 and cortexa8 subtargets.
This patch add missing symbol to generic config.
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
Hans Dedecker [Tue, 19 Feb 2019 14:15:54 +0000 (15:15 +0100)]
Revert "iproute2: use tc package variant to limit other package sizes"
This reverts commit
e6d84fa8864e7bbbcec139dd09a2922a06f5b2a0 as it breaks the
installation of the iproute2 utilities ip-bridge, ss, nstat, devlink and rdma
for the ip-full variant
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
Hans Dedecker [Tue, 19 Feb 2019 14:14:42 +0000 (15:14 +0100)]
Revert "iproute2: simplify linking libelf for eBFP/XDP object file support"
This reverts commit
26681fa6a6fcbec0024906eb8367e9a3160521fb as it breaks the
installation of the iproute2 utilities ip-bridge, ss, nstat, devlink and rdma
for the ip-full variant
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
Hans Dedecker [Tue, 19 Feb 2019 14:12:53 +0000 (15:12 +0100)]
Revert "iproute2: tc: enable and fix support for using .so plugins"
This reverts commit
fc80ef3613465e60257a5ddf0674debe45b09180 as it breaks the
installation of the iproute2 utilities ip-bridge, ss, nstat, devlink and
rdma for the ip-full variant
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
Hans Dedecker [Tue, 19 Feb 2019 14:10:45 +0000 (15:10 +0100)]
Revert "iproute2: tc: reduce size of dynamic symbol table"
This reverts commit
248797834bf21916ddf663edc96d86ee5377850e as it breaks the
installation of the iproute2 utilities ip-bridge, ss, nstat, devlink and rdma
for the ip-full variant
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
Yousong Zhou [Sat, 16 Feb 2019 10:36:55 +0000 (10:36 +0000)]
armvirt: 32: enable CONFIG_ARM_LPAE
This is required for running armvirt_32 on QEMU 3.0 [1], otherwise the
kernel will emit the following complaint and virtio-net-pci devices will
fail to be initialized
[ 1.124214] OF: PCI: host bridge /pcie@
10000000 ranges:
[ 1.125093] OF: PCI: IO 0x3eff0000..0x3effffff -> 0x00000000
[ 1.125942] OF: PCI: MEM 0x10000000..0x3efeffff -> 0x10000000
[ 1.126403] OF: PCI: MEM 0x8000000000..0xffffffffff -> 0x8000000000
[ 1.127748] pci-host-generic
4010000000.pcie: can't claim ECAM area [mem 0x10000000-0x1fffffff]: address conflict with /pcie@
10000000 [mem 0x10000000-0x3efeffff]
[ 1.129752] pci-host-generic: probe of
4010000000.pcie failed with error -16
Running QEMU with "-M virt,highmem=off" is an option, but "highmem" was only
introduced as a default on flag since QEMU 2.5.0 and QEMU will fail and quit on
encounter of unknown flags
[1] Armv7 guest fails to boot with qemu-3.0.0-1,
https://bugzilla.redhat.com/show_bug.cgi?id=
1633328#c5
Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
Yousong Zhou [Sat, 16 Feb 2019 10:36:07 +0000 (10:36 +0000)]
armvirt: 32: refresh kernel config
The diff was genereated by running the following command without
actually changing any kernel config options
make kernel_menuconfig CONFIG_TARGET=subtarget
Here are some initial findings on the change
- CONFIG_ARCH_OPTIONAL_KERNEL_RWX is now arch default
- CONFIG_ARM_GIC_V3_ITS is selected by CONFIG_ARCH_VIRT
- CONFIG_CPU_SPECTRE is select by CONFIG_CPU_V7
- CONFIG_TIMER_OF is now a arch default
- CONFIG_TIMER_PROBE is select by CONFIG_TIMER_OF
The following options should probably be moved to generic config
- CONFIG_MIGRATION is a default on option
- CONFIG_TREE_SRCU is a default on option for !PREEMPT && SMP system
- CONFIG_RCU_NEED_SEGCBLIST
Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
Yousong Zhou [Mon, 18 Feb 2019 14:11:19 +0000 (14:11 +0000)]
dnsmasq: allow using dnsmasq as the sole resolver
Currently it seems impossible to configure /etc/config/dhcp to achieve
the following use case
- run dnsmasq with no-resolv
- re-generate /etc/resolv.conf with "nameserver 127.0.0.1"
Before this change, we have to set resolvfile to /tmp/resolv.conf.auto
to achive the 2nd effect above, but setting resolvfile requires noresolv
being false.
A new boolean option "localuse" is added to indicate that we intend to
use dnsmasq as the local dns resolver. It's false by default and to
align with old behaviour it will be true automatically if resolvfile is
set to /tmp/resolv.conf.auto
Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
Acked-by: Hans Dedecker <dedeckeh@gmail.com>
Daniel Golle [Wed, 13 Feb 2019 18:47:18 +0000 (19:47 +0100)]
mac80211: rt2x00: backport accepted and pending patches from upstream
backport from wireless-drivers-next, replacing some existing patches in
our tree (marked with '=' are those which were already present):
f483039cf51a rt2x00: use simple_read_from_buffer()
=
5c656c71b1bf rt2800: move usb specific txdone/txstatus routines to rt2800lib
=
0b0d556e0ebb rt2800mmio: use txdone/txstatus routines from lib
=
5022efb50f62 rt2x00: do not check for txstatus timeout every time on tasklet
=
adf26a356f13 rt2x00: use different txstatus timeouts when flushing
=
0240564430c0 rt2800: flush and txstatus rework for rt2800mmio
6eba8fd22352 rt2x00: rt2400pci: mark expected switch fall-through
10bb92217747 rt2x00: rt2500pci: mark expected switch fall-through
916e6bbcfcff rt2x00: rt2800lib: mark expected switch fall-throughs
641dd8068ecb rt2x00: rt61pci: mark expected switch fall-through
750afb08ca71 cross-tree: phase out dma_zalloc_coherent()
=
c2e28ef7711f rt2x00: reduce tx power to nominal level on RT6352
a4296994eb80 rt2x00: Work around a firmware bug with shared keys
2587791d5758 rt2x00: no need to check return value of debugfs_create functions
pending on linux-wireless:
rt2x00: remove unneeded check
rt2x00: remove confusing AGC register
rt2800: enable TX_PIN_CFG_LNA_PE_ bits per band
rt2800: enable TX_PIN_CFG_RFRX_EN only for MT7620
rt2800: comment and simplify AGC init for RT6352
rt2x00: do not print error when queue is full
rt2800: partially restore old mmio txstatus behaviour
rt2800: new flush implementation for SoC devices
rt2800: move txstatus pending routine
rt2800mmio: fetch tx status changes
rt2800mmio: use timer and work for handling tx statuses timeouts
rt2x00: remove last_nostatus_check
rt2x00: remove not used entry field
rt2x00mmio: remove legacy comment
While at it also rename some existing patches now that there are
separate folders with patches for each driver to make things a bit
nicer to handle.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Hans Dedecker [Mon, 18 Feb 2019 14:21:06 +0000 (15:21 +0100)]
odhcpd: update to latest git HEAD
1f01299 config: fix build failure in case DHCPv4 support is disabled
67b3a14 dhcpv4: fix assignment of requested IP address
ca8ba91 dhcp: rework static lease logic
36833ea dhcpv6: rapid commit support
1ae316e dhcpv6: fix parsing of DHCPv6 relay messages
80157e1 dhcpv4: fix compile issue
671ccaa dhcpv6-ia: move function definitions to odhcpd.h
0db69b0 dhcpv6: improve code readibility
7847b27 treewide: unify dhcpv6 and dhcpv4 assignments
a54cee0 netlink: rework handling of netlink messages
9f25dd8 treewide: use avl tree to store interfaces
f21a0a7 treewide: align syslog tracing
edc5fb0 dhcpv6-ia: add full CONFIRM support
9d6eadf dhcpv6-ia: rework append_reply()
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
Hauke Mehrtens [Sun, 17 Feb 2019 18:29:08 +0000 (19:29 +0100)]
build: Fix print without color
The original patch removed the printing completely, just remove the
color.
Fixes: eabc1ddc4541 ("build: Honour NO_COLOR in include/scan.mk")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Daniel Engberg [Thu, 8 Nov 2018 23:36:21 +0000 (00:36 +0100)]
toolchain/binutils: Remove 2.30
Remove binutils 2.30
Signed-off-by: Daniel Engberg <daniel.engberg.lists@pyret.net>
Rosy Song [Mon, 7 Jan 2019 06:24:47 +0000 (14:24 +0800)]
samba36: allow build with no ipv6 support
Signed-off-by: Rosy Song <rosysong@rosinson.com>
Paul Wassi [Thu, 27 Dec 2018 13:38:46 +0000 (14:38 +0100)]
uboot-kirkwood: update to 2019.01
Update U-Boot to current 2019.01 release for kirkwood platform
Signed-off-by: Paul Wassi <p.wassi@gmx.at>
Paul Wassi [Thu, 27 Dec 2018 14:39:36 +0000 (15:39 +0100)]
kirkwood: add kernel 4.19 support
Add patches for 4.19
Drop patch 200-disable-tso, as the packet corruption was fixed in
kernel commit
3b89624ab54b9dc2d92fc08ce2670e5f19ad8ec8
Restructure the DTS for Marvell switch in 104-ea3500 and 105-ea4500
to fix DTC warning.
Signed-off-by: Paul Wassi <p.wassi@gmx.at>
Oldřich Jedlička [Tue, 29 Jan 2019 21:25:33 +0000 (22:25 +0100)]
kernel: Added required dependencies for socket match.
This applies to kernel 4.10 and newer.
See https://github.com/torvalds/linux/commit/
8db4c5be88f62ffd7a552f70687a10c614dc697b
The above commit added to kernel 4.10 added new dependency
for building the NETFILTER_XT_MATCH_SOCKET (xt_socket.ko)
module. The NF_SOCKET_IPVx options (both of them) need to
be enabled in order to build the NETFILTER_XT_MATCH_SOCKET
module. Without the change the module is not built.
Signed-off-by: Oldřich Jedlička <oldium.pro@gmail.com>
Lucian Cristian [Wed, 6 Feb 2019 11:42:56 +0000 (13:42 +0200)]
x86: video: disable buildtin amdgpu DRM driver
Signed-off-by: Lucian Cristian <lucian.cristian@gmail.com>
Lucian Cristian [Wed, 6 Feb 2019 11:38:05 +0000 (13:38 +0200)]
x86: video: add amdgpu DRM kernel package
build amdgpu kernel as modules so it will find the firmware files
Signed-off-by: Lucian Cristian <lucian.cristian@gmail.com>
Lucian Cristian [Mon, 4 Feb 2019 10:49:23 +0000 (12:49 +0200)]
x86: DRM: add x64 subtarget support
copy settings from generic subtarget
Signed-off-by: Lucian Cristian <lucian.cristian@gmail.com>
Lucian Cristian [Sun, 3 Feb 2019 16:57:30 +0000 (18:57 +0200)]
x86: video: disable builtin radeon DRM driver
builtin driver can't access the /lib/firmware while booting,
module driver will be able to read and load the firmware files
Signed-off-by: Lucian Cristian <lucian.cristian@gmail.com>
Lucian Cristian [Sun, 3 Feb 2019 16:53:48 +0000 (18:53 +0200)]
x86: video: add radeon DRM module support
add radeon module support so firmware can be loaded from userland
Signed-off-by: Lucian Cristian <lucian.cristian@gmail.com>
Lucian Cristian [Tue, 5 Feb 2019 22:08:10 +0000 (00:08 +0200)]
linux-firmware: DRM: add amdgpu firmware
add firmware needed for amdgpu DRM display
Signed-off-by: Lucian Cristian <lucian.cristian@gmail.com>
Lucian Cristian [Sun, 3 Feb 2019 16:44:16 +0000 (18:44 +0200)]
linux-firmware: DRM: add radeon firmware
add firmware needed for radeon DRM display
Signed-off-by: Lucian Cristian <lucian.cristian@gmail.com>
Hauke Mehrtens [Sat, 16 Feb 2019 22:43:50 +0000 (23:43 +0100)]
strace: Only allow libdw or libunwind
These two dependencies are mutual exclusive and it is only possible to
select one of them, change the select to a chose so it is only possible
to select one of them in OpenWrt menu config.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Peter Wagner [Sun, 10 Feb 2019 13:46:47 +0000 (14:46 +0100)]
strace: fix configuration options
Signed-off-by: Peter Wagner <tripolar@gmx.at>
Peter Wagner [Sun, 10 Feb 2019 13:45:32 +0000 (14:45 +0100)]
elfutils: fix DEPENDS for libelf
Signed-off-by: Peter Wagner <tripolar@gmx.at>
Sven Eckelmann [Mon, 11 Feb 2019 15:26:42 +0000 (16:26 +0100)]
build: Accept BIN_DIR parameter for legacy-images
BIN_DIR can be set to overwrite the output path for new images. This is an
advertised feature for the imagebuilder and is used by systems like
LibreMesh's chef.
The legacy images are build using a new sub-make which doesn't receive the
variable overwrites of the parent make process. As result, the BIN_DIR is
automatically defined to the default value from rules.mk. The images will
therefore not be placed in the output path which was selected by the user.
Providing BIN_DIR as an explicit variable override to the sub-make works
around this problem.
Fixes: 26c771452cd8 ("image.mk: add LegacyDevice wrapper to allow legacy image building code to be used for device profiles")
Reported-by: Paul Spooren <mail@aparcar.org>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Yangbo Lu [Fri, 15 Feb 2019 03:03:14 +0000 (11:03 +0800)]
kernel: disable CONFIG_USB_IMX21_HCD in default for kernel 4.14
CONFIG_USB_IMX21_HCD should be handled in generic config and
module package. So moved it into generic config.
This also fixed build issue (kernel config question) of layerscape
armv8_32b since it also used ARCH_MXC.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
[Deactivate CONFIG_USB_IMX21_HCD also for kernel 4.19]
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Oskari Lemmela [Sun, 27 Jan 2019 18:20:18 +0000 (20:20 +0200)]
sunxi: fix: A64 unstable timer
Backport A64 unstable timer patches from linux 5.1
Signed-off-by: Oskari Lemmela <oskari@lemmela.net>
[Split the single patch into the two original patches]
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Pawel Dembicki [Fri, 15 Feb 2019 15:08:53 +0000 (16:08 +0100)]
sunxi: add support for Sinovoip Banana Pi M2 Plus
CPU: H3 Quad-core Cortex-A7 H.265/HEVC 4K @ 1.2 Ghz
GPU: Mali400MP2 GPU @ 600MHz (supports OpenGL ES 2.0)
Memory: 1GB DDR3 (shared with GPU)
Onboard: Storage TF card (Max. 64GB) / MMC card slot
Onboard: Network 10/100M Ethernet RJ45 (Realtek RTL8211E)
Onboard: Network BT4.0/WiFi 802.11 b/g/n (Ampak AP6212)
Onboard header: SPI, I2C, GPIO, UART
USB 2.0: Two USB 2.0 HOST, One USB 2.0 OTG
Untested:
Audio, Video
Not working:
Bluetooth
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
Pawel Dembicki [Fri, 15 Feb 2019 15:05:43 +0000 (16:05 +0100)]
linux-firmware: broadcom: package
43430a0 FullMAC firmware
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
Eneas U de Queiroz [Fri, 15 Feb 2019 22:35:19 +0000 (22:35 +0000)]
openssl: patch to fix devcrypto sessions leak
Applies a patch from https://github.com/openssl/openssl/pull/8213
that fixes an error where open /dev/crypto sessions were not closed.
Thanks to Ansuel Smith for reporting it.
Signed-off-by: Eneas U de Queiroz <cote2004-github@yahoo.com>
R. Diez [Mon, 21 Jan 2019 18:32:06 +0000 (18:32 +0000)]
build: Honour NO_COLOR in include/scan.mk
The sender domain has a DMARC Reject/Quarantine policy which disallows
sending mailing list messages using the original "From" header.
To mitigate this problem, the original message has been wrapped
automatically by the mailing list software.
Hi all:
This is my first OpenWrt patch. I am a clean, pure newbie! 8-)
Honour NO_COLOR in Makefile function 'progress' in include/scan.mk, in the same way that include/verbose.mk does.
Signed-off-by: R. Diez <rdiezmail-openwrt@yahoo.com>
Tomasz Maciej Nowak [Sun, 13 Jan 2019 20:39:36 +0000 (21:39 +0100)]
x86: image: add test module to bootloader
It was previously added in
546fced, which was part of "intel-microcode:
load as early as possible" series.
Unfortunately the conditionals added to GRUB config caused error on boot,
because on sysupgrade, bootloader is not updated and is left with old
features/modules. Since this module is needed for early microcode load
and transition to this needs to be done step by step, enable the test
module now, so that every newly created image has it already embedded.
Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
Tomasz Maciej Nowak [Sun, 13 Jan 2019 20:37:47 +0000 (21:37 +0100)]
build: remove leftovers from previous x86 commits
VBoxManage is not used and the image is created with proper permisions:
0f5d0f6 image: use internal qemu-img for vmdk and vdi images drop host
dependencies on qemu-utils and VirtualBox
Unreachable config symbols:
9e0759e x86: merge all geode based subtargets into one
No need to define those symbols since x86_64 is subtarget of x86:
196fb76 x86: make x86_64 a subtarget instead of a standalone target
Unreachable config symbols, so remove GRUB_ROOT:
371b382 x86: remove the xen_domu subtarget
Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
Daniel F. Dickinson [Thu, 10 Jan 2019 03:08:26 +0000 (22:08 -0500)]
config: kernel: Fix missing symbol on brcm2708 with CGROUPS
When CGROUP block io is enabled a new symbol is exposed and needs to
be set or unset else kernel oldconfig hangs waiting for input during
normal OpenWrt builds. Therefore add sane defaults for this symbol
in that case. Also, the defaults brcm2708 are different than generic
defaults because the platform's defconfig enables BLK_DEV_THROTTLING
by default (in defconfig config from the patches used to match
upstream's kernel, not in OpenWrt config-4.xx).
Signed-off-by: Daniel F. Dickinson <cshored@thecshore.com>
[make KERNEL_BLK_DEV_THROTTLING_LOW depend on KERNEL_BLK_DEV_THROTTLING]
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Adrian Schmutzler [Sat, 26 Jan 2019 16:59:45 +0000 (17:59 +0100)]
ar71xx: Fix 5 GHz MAC address for Archer C60 v2
Looks like C60 v2 needs the MAC address to be calculated
manually, while the C60 v1 gets it correctly without manual
interference.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Rosen Penev [Wed, 13 Feb 2019 01:03:09 +0000 (17:03 -0800)]
kernel: Remove CONFIG_UDF_NLS for kernel 4.19
kernel 4.18 removed the symbol and made NLS implicit.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Rosen Penev [Thu, 14 Feb 2019 21:07:58 +0000 (13:07 -0800)]
mdadm: Update to 4.1
Tested on GnuBee PC1.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Deng Qingfang [Sat, 9 Feb 2019 06:18:41 +0000 (14:18 +0800)]
iw: update to 5.0.1
Refresh patches
MIPS IPK size increases:
iw-tiny: +3k
iw-full: +10k
Signed-off-by: Deng Qingfang <dengqf6@mail2.sysu.edu.cn>
[Remove sha256, nan, bloom, measurements and ftm from tiny version]
[sync nl80211 between backports and iw]
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Hauke Mehrtens [Fri, 15 Feb 2019 17:43:55 +0000 (18:43 +0100)]
mac80211: update to version 4.19.23-1
This updates mac80211 to backports version 4.19.23-1 which includes all
the stable fixes from kernel 4.19.23.
The removed patches are included in this version.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Jonas Gorski [Sun, 17 Feb 2019 12:04:40 +0000 (13:04 +0100)]
dnsmasq: ensure test and rc order as older than final releases
Opkg treats text after a version number as higher than without:
~# opkg compare-versions "2.80rc1" "<<" "2.80"; echo $?
1
~# opkg compare-versions "2.80rc1" ">>" "2.80"; echo $?
0
This causes opkg not offering final release as upgradable version, and
even refusing to update, since it thinks the installed version is
higher.
This can be mitigated by adding ~ between the version and the text, as ~
will order as less than everything except itself. Since 'r' < 't', to
make sure that test will be treated as lower than rc we add a second ~
before the test tag. That way, the ordering becomes
2.80~~test < 2.80~rc < 2.80
which then makes opkg properly treat prerelease versions as lower.
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
projects / openwrt / staging / blocktrron.git / log