Rosen Penev [Fri, 10 May 2024 22:55:25 +0000 (15:55 -0700)]
mwlwifi: fix compilation with 6.6 and 64-bit
Upstream patch updated to fix kernel 6.6 compilation. It was also split
up into 5. Do the same here.
The patches are taken from this upstreasm PR:
https://github.com/kaloz/mwlwifi/pull/413
Renamed other patches so as to not overlap.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/15452
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
INAGAKI Hiroshi [Sat, 29 Jun 2024 12:57:23 +0000 (21:57 +0900)]
ath79: add support for NEC Aterm WG1800HP2
NEC Aterm WG1800HP2 is a 2.4/5 GHz band 11ac (Wi-Fi 5) router, based on
QCA9558.
Specification:
- SoC : Qualcomm Atheros QCA9558
- RAM : DDR2 128 MiB (2x Nanya NT5TU32M16DG-AC)
- Flash : SPI-NOR 16 MiB (Macronix MX25L12845EMI-10G)
- WLAN : 2.4/5 GHz
- 2.4 GHz : 3T3R (Qualcomm Atheros QCA9558 (SoC))
- 5 GHz : 3T3R (Qualcomm Atheros QCA9880)
- Ethernet : 5x 10/100/1000 Mbps
- switch : Atheros AR8327
- LEDs/Keys (GPIO) : 12x/5x
- UART : through-hole on PCB
- assignment : 3.3V, GND, NC, TX, RX from tri-angle marking
- settings : 9600n8
- USB : 1x USB 2.0 Type-A
- hub (internal) : NEC uPD720114
- Power : 12 VDC, 1.5 A (Max. 17 W)
- Stock OS : NetBSD based
Flash instruction using initramfs-factory.bin image (StockFW WebUI):
1. Boot WG1800HP2 with router mode normally
2. Access to the WebUI ("http://aterm.me/" or "http://192.168.0.1/") on
the device and open firmware update page ("ファームウェア更新")
3. Select the OpenWrt initramfs-factory.bin image and click update
("更新") button
4. After updating, the device will be rebooted and booted with OpenWrt
initramfs image
5. On the initramfs image, upload (or download) uboot.bin and
sysupgrade.bin image to the device
6. Replace the bootloader with a uboot.bin image
mtd write <uboot.bin image> bootloader
7. Perform sysupgrade with a sysupgrade.bin image
sysupgrade <sysupgrade image>
8. Wait ~120 seconds to complete flashing
Flash instruction using initramfs-factory.bin image (bootloader CLI):
1. Connect and open serial console
2. Power on WG1800HP2 and interrupt bootloader by ESC key
3. Login to the bootloader CLI with a password "chiron"
4. Start TFTP server by "tftpd" command
5. Upload initramfs-factory.bin via tftp from your computer
example (Windows): tftp -i 192.168.0.1 PUT initramfs-factory.bin
6. Boot initramfs image by "boot" command
7. On the initramfs image, back up the stock bootloader and firmware if
needed
8. Upload (or download) uboot.bin and sysupgrade.bin image to the device
9. Replace the bootloader with a uboot.bin image
10. Perform sysupgrade with a sysupgrade.bin image
11. Wait ~120 seconds to complete flashing
Notes:
- All LEDs are connected to the TI TCA6416A (marking: PH416A) I2C
Expander chip.
- The stock bootloader requires an unknown filesystem on firmware area
in the flash. Booting of OpenWrt from that filesystem cannot be
handled, so the bootloader needs to be replaced to mainline U-Boot
before OpenWrt installation.
MAC addresses:
LAN : A4:12:42:xx:xx:44 (config, 0x6 (hex))
WAN : A4:12:42:xx:xx:45 (config, 0xc (hex))
2.4 GHz: A4:12:42:xx:xx:46 (config, 0x0 (hex))
5 GHz : A4:12:42:xx:xx:47 (config, 0x12 (hex))
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16297
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
INAGAKI Hiroshi [Sat, 29 Jun 2024 12:53:42 +0000 (21:53 +0900)]
ath79: add support for NEC Aterm WG1800HP
NEC Aterm WG1800HP is a 2.4/5 GHz band 11ac (Wi-Fi 5) router, based on
QCA9558.
Specification:
- SoC : Qualcomm Atheros QCA9558
- RAM : DDR2 128 MiB (2x Nanya NT5TU32M16DG-AC)
- Flash : SPI-NOR 16 MiB (Macronix MX25L12845EMI-10G)
- WLAN : 2.4/5 GHz
- 2.4 GHz : 3T3R (Qualcomm Atheros QCA9558 (SoC))
- 5 GHz : 3T3R (Qualcomm Atheros QCA9880)
- Ethernet : 5x 10/100/1000 Mbps
- switch : Atheros AR8327
- LEDs/Keys (GPIO) : 12x/5x
- UART : through-hole on PCB
- assignment : 3.3V, GND, NC, TX, RX from tri-angle marking
- settings : 9600n8
- USB : 1x USB 2.0 Type-A
- hub (internal) : NEC uPD720114
- Power : 12 VDC, 1.5 A (Max. 17 W)
- Stock OS : NetBSD based
Flash instruction using initramfs-factory.bin image (StockFW WebUI):
1. Boot WG1800HP with router mode normally
2. Access to the WebUI ("http://aterm.me/" or "http://192.168.0.1/") on
the device and open firmware update page ("ファームウェア更新")
3. Downgrade the stock firmware to v1.0.2
4. After downgrading, select the OpenWrt initramfs-factory.bin image and
click update ("更新") button
5. After updating, the device will be rebooted and booted with OpenWrt
initramfs image
6. On the initramfs image, upload (or download) uboot.bin and
sysupgrade.bin image to the device
7. Replace the bootloader with a uboot.bin image
mtd write <uboot.bin image> bootloader
8. Perform sysupgrade with a sysupgrade.bin image
sysupgrade <sysupgrade image>
9. Wait ~120 seconds to complete flashing
Flash instruction using initramfs-factory.bin image (bootloader CLI):
1. Connect and open serial console
2. Power on WG1800HP and interrupt bootloader by ESC key
3. Login to the bootloader CLI with a password "chiron"
4. Start TFTP server by "tftpd" command
5. Upload initramfs-factory.bin via tftp from your computer
example (Windows): tftp -i 192.168.0.1 PUT initramfs-factory.bin
6. Boot initramfs image by "boot" command
7. On the initramfs image, back up the stock bootloader and firmware if
needed
8. Upload (or download) uboot.bin and sysupgrade.bin image to the device
9. Replace the bootloader with a uboot.bin image
10. Perform sysupgrade with a sysupgrade.bin image
11. Wait ~120 seconds to complete flashing
Notes:
- All LEDs are connected to the TI TCA6416A (marking: PH416A) I2C
Expander chip.
- The stock bootloader requires an unknown filesystem on firmware area
in the flash. Booting of OpenWrt from that filesystem cannot be
handled, so the bootloader needs to be replaced to mainline U-Boot
before OpenWrt installation.
- The data length of blocks in firmware image will be checked
(4M < threshold < 6M) on the stock WebUI on some versions (v1.0.28,
v1.0.30(latest), ...), so needs to be downgraded before OpenWrt
installation with initramfs-factory image.
MAC addresses:
LAN : 10:66:82:xx:xx:04 (config, 0x6 (hex))
WAN : 10:66:82:xx:xx:05 (config, 0xc (hex))
2.4 GHz: 10:66:82:xx:xx:06 (config, 0x0 (hex))
5 G : 10:66:82:xx:xx:07 (config, 0x12 (hex))
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16297
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
INAGAKI Hiroshi [Sat, 2 Mar 2019 17:48:18 +0000 (02:48 +0900)]
ath79: add support for NEC Aterm WG1400HP
NEC Aterm WG1400HP is a 2.4/5 GHz band 11ac (Wi-Fi 5) router, based on
QCA9558.
Specification:
- SoC : Qualcomm Atheros QCA9558
- RAM : DDR2 128 MiB (2x Nanya NT5TU32M16DG-AC)
- Flash : SPI-NOR 16 MiB (Macronix MX25L12845EMI-10G)
- WLAN : 2.4/5 GHz
- 2.4 GHz : 3T3R (Qualcomm Atheros QCA9558 (SoC))
- 5 GHz : 2T2R (Qualcomm Atheros QCA9882)
- Ethernet : 5x 10/100/1000 Mbps
- switch : Atheros AR8327
- LEDs/Keys (GPIO) : 12x/5x
- UART : through-hole on PCB
- assignment : 3.3V, GND, NC, TX, RX from tri-angle marking
- settings : 9600n8
- USB : 1x USB 2.0 Type-A
- hub (internal) : NEC uPD720114
- Power : 12 VDC, 1.5 A (Max. 17 W)
- Stock OS : NetBSD based
Flash instruction using initramfs-factory.bin image (StockFW WebUI):
1. Boot WG1400HP with router mode normally
2. Access to the WebUI ("http://aterm.me/" or "http://192.168.0.1/") on
the device and open firmware update page ("ファームウェア更新")
3. Select the OpenWrt initramfs-factory.bin image and click update
("更新") button
4. After updating, the device will be rebooted and booted with OpenWrt
initramfs image
5. On the initramfs image, upload (or download) uboot.bin and
sysupgrade.bin image to the device
6. Replace the bootloader with a uboot.bin image
mtd write <uboot.bin image> bootloader
7. Perform sysupgrade with a sysupgrade.bin image
sysupgrade <sysupgrade image>
8. Wait ~120 seconds to complete flashing
Flash instruction using initramfs-factory.bin image (bootloader CLI):
1. Connect and open serial console
2. Power on WG1400HP and interrupt bootloader by ESC key
3. Login to the bootloader CLI with a password "chiron"
4. Start TFTP server by "tftpd" command
5. Upload initramfs-factory.bin via tftp from your computer
example (Windows): tftp -i 192.168.0.1 PUT initramfs-factory.bin
6. Boot initramfs image by "boot" command
7. On the initramfs image, back up the stock bootloader and firmware if
needed
8. Upload (or download) uboot.bin and sysupgrade.bin image to the device
9. Replace the bootloader with a uboot.bin image
10. Perform sysupgrade with a sysupgrade.bin image
11. Wait ~120 seconds to complete flashing
Notes:
- All LEDs are connected to the TI TCA6416A (marking: PH416A) I2C
Expander chip.
- The stock bootloader requires an unknown filesystem on firmware area
in the flash. Booting of OpenWrt from that filesystem cannot be
handled, so the bootloader needs to be replaced to mainline U-Boot
before OpenWrt installation.
MAC addresses:
LAN : 10:66:82:xx:xx:20 (config, 0x6 (hex))
WAN : 10:66:82:xx:xx:21 (config, 0xc (hex))
2.4 GHz: 10:66:82:xx:xx:22 (config, 0x0 (hex))
5 GHz : 10:66:82:xx:xx:23 (config, 0x12 (hex))
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16297
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
INAGAKI Hiroshi [Thu, 27 Jun 2024 15:53:31 +0000 (00:53 +0900)]
ath79: commonize SGMII calibration functions of QCA955x in lzma-loader
Commonize function names of SGMII calibration functions of QCA955x added
for Meraki MR18, to use them for NEC Aterm series based on QCA9558 as
well.
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16297
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
INAGAKI Hiroshi [Thu, 27 Jun 2024 06:51:34 +0000 (15:51 +0900)]
ath79: add missing usb-phy-analog reset to usb phys for QCA955x
Add missing reset bits of USB phys on QCA955x SoCs to qca955x.dtsi to
handle them.
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16297
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
INAGAKI Hiroshi [Sat, 31 Aug 2024 08:59:41 +0000 (17:59 +0900)]
uboot-ath79: refresh patches
Refresh patches by "make package/uboot-ath79/prepare" and manual
adjustments.
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16297
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
INAGAKI Hiroshi [Sat, 31 Aug 2024 08:46:54 +0000 (17:46 +0900)]
uboot-ath79: add support for NEC Aterm series based on QCA9558
Add support for NEC Aterm series devices based on QCA9558.
The following devices have almost the same hardware, so the same U-Boot
binary can be used for them.
- NEC Aterm WG1400HP
- NEC Aterm WG1800HP
- NEC Aterm WG1800HP2
By the way, on NetBSD-based NEC Aterm devices, only 0x20000 (128KiB) is
available for a bootloader on the flash chip and that limitation is too
small for mainline U-Boot with the default options. So many
features/commands not required for booting OpenWrt and recoverying are
disabled on that devices, like the followings.
- networking support
- FIT support
- all decompression methods support
etc...
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16297
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
INAGAKI Hiroshi [Sat, 31 Aug 2024 08:42:53 +0000 (17:42 +0900)]
uboot-ath79: add initial support for QCA955x SoCs
Add initial support for Qualcomm Atheros QCA955x series SoCs.
This support was based on the QCA956x support, QSDK, GPL tar of TP-Link
Archer C5 v1.20.
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16297
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Stefan Lippers-Hollmann [Thu, 17 Oct 2024 15:37:02 +0000 (17:37 +0200)]
mac80211: realtek: rtlwifi: add RTL8192DU support
Add Realtek RTL8192DU support to the rtlwifi package.
The RTL8192DU chipset is a 802.11a/b/g/n chip which supports 2.4 and 5 GHz at
up to 40 MHz channel bandwidth, three hardware variations exist:
* single MAC/ single PHY
* single MAC/ double PHY
* double MAC/ double PHY
This driver has been successully tested on a single MAC/ single PHY variant
0bda:8194 (DeLock 88540, https://www.delock.com/produkt/88540/merkmale.html)
rtl_usb: rx_max_size 15360, rx_urb_num 8, in_ep 1
rtl8192du: Driver for Realtek RTL8192DU WLAN interface
rtl8192du: Loading firmware file rtlwifi/rtl8192dufw.bin
ieee80211 phy0: Selected rate control algorithm 'rtl_rc'
usbcore: registered new interface driver rtl8192du
Supported interface modes:
* IBSS
* managed
* AP
* AP/VLAN
* monitor
* mesh point
* P2P-client
* P2P-GO
interface combinations are not supported
The new rtlwifi based driver rtl8192du has been merged in kernel v6.11.
Signed-off-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/16721
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Stefan Lippers-Hollmann [Thu, 17 Oct 2024 15:31:58 +0000 (17:31 +0200)]
linux-firmware: add firmware for Realtek RTL8192DU
This commit packages the newly merged firmware (v39.0) for Realtek RTL8192DU
802.11a/b/g/n USB wireless cards.
Signed-off-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/16721
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Stefan Lippers-Hollmann [Thu, 17 Oct 2024 15:30:47 +0000 (17:30 +0200)]
linux-firmware: Update to version
20241017
This updates the following firmware files:
amdgpu/gc_11_5_2_imu.bin
amdgpu/gc_11_5_2_me.bin
amdgpu/gc_11_5_2_mec.bin
amdgpu/gc_11_5_2_mes1.bin
amdgpu/gc_11_5_2_mes_2.bin
amdgpu/gc_11_5_2_pfp.bin
amdgpu/gc_11_5_2_rlc.bin
amdgpu/psp_14_0_4_ta.bin
amdgpu/psp_14_0_4_toc.bin
amdgpu/sdma_6_1_2.bin
amdgpu/vpe_6_1_3.bin
ath12k/QCN9274/hw2.0/board-2.bin
ath12k/QCN9274/hw2.0/firmware-2.bin
ath12k/QCN9274/hw2.0/Notice.txt
brcm/brcmfmac4354-sdio.nvidia,p2371-2180.txt
cirrus/cs35l54-b0-dsp1-misc-
103c8d85-amp1.bin
cirrus/cs35l54-b0-dsp1-misc-
103c8d85-amp2.bin
cirrus/cs35l54-b0-dsp1-misc-
103c8d85-amp3.bin
cirrus/cs35l54-b0-dsp1-misc-
103c8d85-amp4.bin
cirrus/cs35l54-b0-dsp1-misc-
103c8d86-amp1.bin
cirrus/cs35l54-b0-dsp1-misc-
103c8d86-amp2.bin
cirrus/cs35l54-b0-dsp1-misc-
103c8d86-amp3.bin
cirrus/cs35l54-b0-dsp1-misc-
103c8d86-amp4.bin
cirrus/cs35l54-b0-dsp1-misc-
103c8d8c-amp1.bin
cirrus/cs35l54-b0-dsp1-misc-
103c8d8c-amp2.bin
cirrus/cs35l54-b0-dsp1-misc-
103c8d8d-amp1.bin
cirrus/cs35l54-b0-dsp1-misc-
103c8d8d-amp2.bin
cirrus/cs35l54-b0-dsp1-misc-
103c8d8e-amp1.bin
cirrus/cs35l54-b0-dsp1-misc-
103c8d8e-amp2.bin
cirrus/cs35l54-b0-dsp1-misc-
103c8e14-amp1.bin
cirrus/cs35l54-b0-dsp1-misc-
103c8e14-amp2.bin
cirrus/cs35l54-b0-dsp1-misc-
103c8e15-amp1.bin
cirrus/cs35l54-b0-dsp1-misc-
103c8e15-amp2.bin
cirrus/cs35l54-b0-dsp1-misc-
103c8e1b-amp1.bin
cirrus/cs35l54-b0-dsp1-misc-
103c8e1b-amp2.bin
cirrus/cs35l56-b0-dsp1-misc-
103c8d90-amp1.bin
cirrus/cs35l56-b0-dsp1-misc-
103c8d90-amp2.bin
cirrus/cs35l56-b0-dsp1-misc-
10431e13-amp1.bin
cirrus/cs35l56-b0-dsp1-misc-
10431e13-amp2.bin
cirrus/cs35l56-b0-dsp1-misc-
10431e13-amp3.bin
cirrus/cs35l56-b0-dsp1-misc-
10431e13-amp4.bin
cirrus/cs35l56-b0-dsp1-misc-
10431f43-amp1.bin
cirrus/cs35l56-b0-dsp1-misc-
10431f43-amp2.bin
cirrus/cs35l56-b0-dsp1-misc-
10431f43-amp3.bin
cirrus/cs35l56-b0-dsp1-misc-
10431f43-amp4.bin
cirrus/cs35l56-b0-dsp1-misc-
17aa380e-spkid0-ampl.bin
cirrus/cs35l56-b0-dsp1-misc-
17aa380e-spkid0-ampr.bin
cirrus/cs35l56-b0-dsp1-misc-
17aa380e-spkid1-ampl.bin
cirrus/cs35l56-b0-dsp1-misc-
17aa380e-spkid1-ampr.bin
cirrus/cs35l56/CS35L56_Rev3.11.11.1.wmfw
cirrus/cs35l56/CS35L56_Rev3.11.20.wmfw
iwlwifi-bz-b0-fm-c0-94.ucode
iwlwifi-gl-c0-fm-c0-94.ucode
mediatek/BT_RAM_CODE_MT7961_1a_2_hdr.bin
mediatek/mt7988/mt7988_wo_0.bin
mediatek/mt7988/mt7988_wo_1.bin
mediatek/mt7996/mt7992_dsp_23.bin
mediatek/mt7996/mt7992_dsp.bin
mediatek/mt7996/mt7992_eeprom_23_2i5i.bin
mediatek/mt7996/mt7992_eeprom_23.bin
mediatek/mt7996/mt7992_eeprom_2i5e.bin
mediatek/mt7996/mt7992_eeprom_2i5i.bin
mediatek/mt7996/mt7992_eeprom.bin
mediatek/mt7996/mt7992_rom_patch_23.bin
mediatek/mt7996/mt7992_rom_patch.bin
mediatek/mt7996/mt7992_wa_23.bin
mediatek/mt7996/mt7992_wa.bin
mediatek/mt7996/mt7992_wm_23.bin
mediatek/mt7996/mt7992_wm.bin
mediatek/mt7996/mt7996_eeprom_233_2i5i6i.bin
mediatek/mt7996/mt7996_eeprom_233.bin
mediatek/mt7996/mt7996_eeprom_2i5i6i.bin
mediatek/mt7996/mt7996_rom_patch_233.bin
mediatek/mt7996/mt7996_wa_233.bin
mediatek/mt7996/mt7996_wm_233.bin
mediatek/WIFI_MT7961_patch_mcu_1a_2_hdr.bin
mediatek/WIFI_RAM_CODE_MT7961_1a.bin
qca/hmtbtfw20.tlv
qca/hmtnv20.b10f
qca/hmtnv20.b112
qca/hmtnv20.bin
qcom/a663_gmu.bin
qcom/qcm6490/a660_zap.mbn
qcom/qcm6490/adsp.mbn
qcom/qcm6490/adspr.jsn
qcom/qcm6490/adsps.jsn
qcom/qcm6490/adspua.jsn
qcom/qcm6490/battmgr.jsn
qcom/qcm6490/cdsp.mbn
qcom/qcm6490/cdspr.jsn
qcom/qcm6490/ipa_fws.mbn
qcom/sa8775p/a663_zap.mbn
realtek/rt1320/rt1320-patch-code-vab.bin
realtek/rt1320/rt1320-patch-code-vc.bin
rtl_nic/rtl8125d-1.fw
rtlwifi/rtl8192dufw.bin
rtw89/rtw8922a_fw-2.bin
ti/tas2781/TAS2XXX1EB30.bin
ti/tas2781/TAS2XXX1EB31.bin
Signed-off-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/16721
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Rosen Penev [Mon, 15 Jul 2024 05:59:08 +0000 (22:59 -0700)]
ath79: apply qca,tx-gain-buffalo
It seems this was only used by one device in ar71xx. Might as well
reapply it.
Make use of the separate TX gain table for WZR-HP-G450H:
https://github.com/torvalds/linux/commit/
0f978bfaf2600040f9826f394eb12e023bef3068
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/15949
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Samuele Longhi [Sat, 12 Oct 2024 16:20:49 +0000 (18:20 +0200)]
ramips: mt7621: add support for Gemtek WVRTM-127ACN and WVRTM-130ACN
The Gemtek WVRTM-127ACN is an indoor dual band wifi router
with internal antennas and 3 Gigabit Ethernet ports.
The Gemtek WVRTM-130ACN is an indoor dual band wifi router
with external antennas and 5 Gigabit Ethernet ports.
Hardware of WVRTM-127ACN:
- SoC: Mediatek MT7621AT (880 MHz, dual core)
- RAM: 128 MB
- Storage: 128 MB NAND SLC flash
- Ethernet: 3x 10/100/1000 Mbps LAN1,LAN2 & WAN
- Wireless: 2.4GHz: Mediatek MT7603EN (802.11b/g/n)
- Wireless: 5GHz: Mediatek MT7612EN (802.11n/ac)
- LEDs: 11x
- Buttons: 2x WPS, reset
- USB: 1x 3.0
- Power: 56 VDC, 0.54 A, PoE+ IN (WAN)
- PoE: 1x PoE+ 802.3af/at (WAN)
- Uart: GND RX TX VCC - J2 (GND near WAN)
- Board silkscreen: "WVRTM-127ACN_V02" "19K-513-8500R" "RoHS" "1717"
Hardware of WVRTM-130ACN:
- SoC: Mediatek MT7621AT (880 MHz, dual core)
- RAM: 128 MB (Kioxia TC58BVG0S3HTA00)
- Storage: 128 MB NAND SLC (Winbond W971GG6SB-25)
- Ethernet: 5x 10/100/1000 Mbps LAN1,LAN2,LAN3,LAN4 & WAN
- Wireless: 2.4GHz and 5GHz Mediatek MT7615DN (802.11ac/b/g/n) (DBDC)
- LEDs: 10x
- Buttons: 3x Power, WPS, reset
- USB: 1x 3.0
- Power: 56 VDC, 0.54 A, PoE+ (WAN)
- PoE: 1x PoE+ 802.3af/at (WAN)
- Uart: GND RX TX VCC - J2 (GND near WAN)
- Board silkscreen: "WVRTM-130ACN_V01" "19K-515-4500R" "RoHS" "2112"
Enable access to uboot menu (needed in wvrtm-130acn):
- The access to uboot menu is blocked by `bootdelay = 0` set in ubootenv.
With stock firmware version 01.01.02.163 and previous, you can use CVE 2020-24365
command injection https://nvd.nist.gov/vuln/detail/CVE-2020-24365
python3 exploit.py -t 192.168.1.1 -c "fw_setenv bootdelay 3; fw_saveenv"
Backup the stock firmware:
- Connect via uart
- Connect via ethernet and assign your pc the address 192.168.15.x/24
- Power on the device; and start typing '4' to enter uboot menu
- Set factory mode and boot
MT7621 # setenv factory 2; saveenv
MT7621 # nand read
2800000 2000000 81000000; bootm
- Telnet and copy all mtd blocks
telnet 192.168.15.1
- Copy all mtd blocks and start webserver
for N in $(seq 0 6); do dd if=/dev/mtd$N of=/tmp/eeprom_mtd$N.bin; done
mount -o bind /tmp /www
lighttpd -f /etc/lighttpd.conf
- Backup stock rootfs_data (optional)
dd if=/dev/mtd7 of=/tmp/eeprom_mtd7.bin
dd if=/dev/mtd8 of=/tmp/eeprom_mtd8.bin
- Download to your pc from http://192.168.15.1/eeprom_mtd$N.bin
Installation:
- Connect via uart
- Connect via ethernet and assign your pc the address 10.10.10.3/24
- Start a tftp server and serve the image initramfs-kernel.bin
mkdir /tmp/ftpd;
cp initramfs-kernel.bin /tmp/ftpd/kernel.bin
dnsmasq --enable-tftp --tftp-root=/tmp/ftpd
- Power on the device; and start typing '4' to halt the bootloader
- Change the active mtd partition from mtd6 to mtd5 (needed by uboot)
MT7621 # setenv mtddevnum 5; saveenv
- Write the openwrt initramfs in ram via tftp and boot it
MT7621 # tftpboot
81000000 kernel.bin; bootm
- From the initramfs create the ubi device and install openwrt via sysupgrade
ubiformat /dev/mtd11 -y
sysupgrade -n -v /tmp/sysupgrade.bin
Recovery:
Restore the stock firmware from the backup of the mtd blocks
mtd write eeprom_mtd5.bin firmware
mtd write eeprom_mtd6.bin Kernel2
mtd write eeprom_mtd7.bin Storage1
mtd write eeprom_mtd8.bin Storage2
ubiformat /dev/mtd8 -y
reboot
Links to previous works on wvrtm-127acn:
https://github.com/digiampietro/hacking-gemtek
https://forum.openwrt.org/t/add-support-for-gemtek-wvrtm-127acn-linkem-provider/168757
Signed-off-by: Samuele Longhi <agave@dracaena.it>
Link: https://github.com/openwrt/openwrt/pull/16685
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
John Audia [Thu, 17 Oct 2024 23:46:24 +0000 (19:46 -0400)]
kernel: bump 6.6 to 6.6.57
1. Update target/linux/generic/config-6.6 for new ksym
2. Refresh patches
Changelog: https://cdn.kernel.org/pub/linux/kernel/v6.x/ChangeLog-6.6.57
Added:
generic/backport-6.6/777-netfilter-xtables-fix-typo-causing-some-targets-to-not-load-on-IPv6.patch[1]
Manually rebased:
generic/hack-6.6/645-netfilter-connmark-introduce-set-dscpmark.patch
Removed upstreamed:
gemini/patches-6.6/0001-net-ethernet-cortina-Drop-TSO-support.patch[2]
gemini/patches-6.6/0004-net-ethernet-cortina-Restore-TSO-support.patch[3]
All other patches automatically rebased.
1. https://lore.kernel.org/all/
20241019-xtables-typos-v2-1-
6b8b1735dc8e@0upti.me/
2 https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v6.6.57&id=
452c0740d72c6a77a41f6ddc318a48f18c3d2346
3. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v6.6.57&id=
611f74b0e7fb93ee2366d9d7edca546806b220e9
Build system: x86/64
Build-tested: x86/64/AMD Cezanne, flogic/xiaomi_redmi-router-ax6000-ubootmod, ramips/tplink_archer-a6-v3
Run-tested: x86/64/AMD Cezanne, flogic/xiaomi_redmi-router-ax6000-ubootmod, ramips/tplink_archer-a6-v3
Signed-off-by: John Audia <therealgraysky@proton.me>
Link: https://github.com/openwrt/openwrt/pull/16726
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Hannu Nyman [Thu, 17 Oct 2024 17:33:36 +0000 (20:33 +0300)]
base-files: increase default system log size to 128 kB
Increase the default system log buffer size option
in /etc/config/system from 64 kB to 128 kB.
64 kB is barely enough for the boot items of a modern router
with a few add-on packages, but any subsequent logging will
quickly cause the early boot items to get overwritten in the
round-robin log buffer. Double the buffer size to 128 kB.
(Note: built-in default in ubox logd itself is still 16 kB)
Signed-off-by: Hannu Nyman <hannu.nyman@iki.fi>
Link: https://github.com/openwrt/openwrt/pull/16723
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Roger Pueyo Centelles [Fri, 18 Nov 2022 00:18:09 +0000 (01:18 +0100)]
ath79: Upstream b53 DSA driver for Ubiquiti EdgeSwitch 8XP
The swconfig-based b53 driver for the BCM53128 switch stopped working
after commits
b2cfed48f6 (Revert "swconfig: fix Broadcom b53 support")
and
e4e410733f (kernel: export switch_generic_set_link() symbol). This
rendered the 8 LAN ports of the EdgeSwitch 8XP non-functional, so the
image compilation for the device was disabled (
5a1d7d8c1b).
This commit adds the kmod-dsa-b53-mdio and kmod-dsa-b53 packages
with the upstream B53 DSA driver, replacing the swconfig-based
kmod and kmod-switch-bcm53xx-mdio downstream ones that are not used by
any other device.
The 8 LAN ports of the EdgeSwitch 8XP are usable again. The 02_network
init script has been updated with the new DSA interfaces lan1 .. lan8.
Image building has been reenabled for the device, adding the usual DSA
incompatibility notice.
Tested on a Ubiquiti EdgeSwitch 8XP.
Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
Link: https://github.com/openwrt/openwrt/pull/11680
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Daniel Golle [Fri, 18 Oct 2024 11:38:21 +0000 (12:38 +0100)]
mediatek: filogic: convert Acer Predator W6 to use NVMEM framework
Read WiFi calibration data via NVMEM framework. The MAC addresses are
stored inside a file on a filesystem and hence still have to be
extracted in userspace.
WiFI EEPROM extraction has already accidentally been partially removed
by commit
3e6de5d77a ("mediatek: use NVMEM framework on all Adtran
devices").
Fixes: 3e6de5d77a ("mediatek: use NVMEM framework on all Adtran devices")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Felix Fietkau [Fri, 18 Oct 2024 06:03:21 +0000 (08:03 +0200)]
firewall: update to Git HEAD (2024-10-18)
ffba75c9cd8f iptables: free xtables_match if found in need_protomatch
bf1d5fdf6234 iptables: fix regression with unintended free in need_protomatch
1aef9791a21e defaults.c: fix ipv6 flow offloading
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Robert Marko [Thu, 17 Oct 2024 16:37:47 +0000 (18:37 +0200)]
lantiq: refresh patches
CI says that they need to be refreshed, so do so.
Link: https://github.com/openwrt/openwrt/pull/16722
Signed-off-by: Robert Marko <robimarko@gmail.com>
Robert Marko [Thu, 17 Oct 2024 16:37:27 +0000 (18:37 +0200)]
realtek: refresh patches
CI says that they need to be refreshed, so do so.
Link: https://github.com/openwrt/openwrt/pull/16722
Signed-off-by: Robert Marko <robimarko@gmail.com>
Jack Sun [Thu, 17 Oct 2024 11:37:38 +0000 (19:37 +0800)]
package: busybox: update download link
There is no file named busybox-1.36.1.tar.bz2 in the root directory of the website
The actual download link is “https://sources.buildroot.net/busybox/busybox-1.36.1.tar.bz2”
Signed-off-by: Jack Sun <sunjiazheng321521@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16719
Signed-off-by: Robert Marko <robimarko@gmail.com>
Hannu Nyman [Wed, 16 Oct 2024 19:03:34 +0000 (22:03 +0300)]
base-files: Increase failsafe trigger wait time from 2 to 4 sec
Increase the failsafe waiting timeout period from 2 seconds
to 4 seconds.
Since commit
29207748b in 2015 we have had a rapid LED blinking
indication for the failsafe triggering period. But the really short
timeout of 2 seconds requires snappy reaction time from the user to
notice the LED blinking and to push button inside the short window.
Relax the timeout to 4 seconds, which more easily allows to notice
the change in LED blinking and push a button.
Signed-off-by: Hannu Nyman <hannu.nyman@iki.fi>
Link: https://github.com/openwrt/openwrt/pull/11852
Signed-off-by: Robert Marko <robimarko@gmail.com>
Robert Marko [Thu, 17 Oct 2024 12:27:04 +0000 (14:27 +0200)]
ath11k-firmware: update IPQ8074 and QCN9074 to 2.9.0.1-02146
After a long time QCA has pushed an updated release of 2.9.0.1 firmware
for IPQ8074 and QCN9074, so lets update to 2.9.0.1-02146.
Sadly, still nothing new for IPQ6018.
QCA has also moved the repository where they will be posting firmware to
their CodeLinaro instance, so we move to using that and it allows us to
remove the manual download of QCN9074 board-2.bin.
Link: https://github.com/openwrt/openwrt/pull/16720
Signed-off-by: Robert Marko <robimarko@gmail.com>
Daniel Golle [Thu, 17 Oct 2024 12:33:18 +0000 (13:33 +0100)]
generic: import and move accepted RealTek PHY patches
Import commits from upstream Linux and move/rename existing patches
which have been acceped.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
David Bauer [Wed, 22 Nov 2023 01:45:13 +0000 (02:45 +0100)]
mpc85xx: convert Watchguard T10 mac-assignment to NVMEM
MAC-addresses are stored with colons, thus they can now be referenced
using NVMEM.
Signed-off-by: David Bauer <mail@david-bauer.net>
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16310
Signed-off-by: Robert Marko <robimarko@gmail.com>
Rosen Penev [Wed, 16 Oct 2024 22:31:20 +0000 (15:31 -0700)]
mpc85xx: p1010: fix NAND devices
Upstream commit
9ba0cae3cac07c21c583f9ff194f74043f90d29c made FSL_IFC
visible and selectable, which means that in order for MTD_NAND_FSL_IFC
to work, it needs these two extra CONFIG options.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16717
Signed-off-by: Robert Marko <robimarko@gmail.com>
INAGAKI Hiroshi [Sun, 13 Oct 2024 15:31:43 +0000 (00:31 +0900)]
uboot-ath79: update to U-Boot v2024.10
Update uboot-ath79 package to U-Boot v2024.10.
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16703
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Chukun Pan [Thu, 10 Oct 2024 15:10:28 +0000 (23:10 +0800)]
mac80211: realtek: rtw89: add RTL8922AE support
Add the Realtek RTL8922AE support to rtw89 package.
The 8922A is a 802.11be chip that can support 2/5/6GHz 160MHz.
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
Link: https://github.com/openwrt/openwrt/pull/16700
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Chukun Pan [Wed, 9 Oct 2024 15:10:26 +0000 (23:10 +0800)]
linux-firmware: update Realtek RTW89 firmware
Add RealTek RTL8922AE firmware package. The rtw89 driver uses
rtw8852b_fw-1.bin starting from kernel 6.4[1], remove the old
one. Also note that in the kernel 6.12, rtw8852c and rtw8922a
should use fw-1.bin [2][3].
[1] https://github.com/torvalds/linux/commit/
ffde7f3476
[2] https://github.com/torvalds/linux/commit/
45ae0e8cf8
[3] https://github.com/torvalds/linux/commit/
6ca6b918f2
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
Suggested-by: Hauke Mehrtens <hauke@hauke-m.de>
Link: https://github.com/openwrt/openwrt/pull/16700
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Andre Heider [Mon, 9 Jan 2023 15:38:05 +0000 (16:38 +0100)]
prereq-build: limit python distutils check to <v3.12
v3.12 won't have it anymore.
Signed-off-by: Andre Heider <a.heider@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16699
Signed-off-by: Robert Marko <robimarko@gmail.com>
Paul Spooren [Sat, 17 Aug 2024 14:23:54 +0000 (16:23 +0200)]
prereq-build: add Python 3.12 support
This reverts commit
09b7e1955c92e0b05197174b7bd4aef2c4073a35.
Signed-off-by: Paul Spooren <mail@aparcar.org>
Link: https://github.com/openwrt/openwrt/pull/16699
Signed-off-by: Robert Marko <robimarko@gmail.com>
Robert Marko [Wed, 16 Oct 2024 09:14:54 +0000 (11:14 +0200)]
opkg: update to Git HEAD (2024-10-16)
38eccbb1fd69 libopkg: allow install package from https and ftps
Link: https://github.com/openwrt/openwrt/pull/16715
Signed-off-by: Robert Marko <robimarko@gmail.com>
Felix Fietkau [Wed, 16 Oct 2024 07:55:18 +0000 (09:55 +0200)]
ramips: disable CONFIG_LIST_HARDENED on MT7620
In #16396, crashes were reported on MT7620, which were introduced by enabling
CONFIG_LIST_HARDENED. The cause seems to be random memory corruption somewhere
in the kernel. Unfortunately the crash traces do not point to the real cause
of the crash in any way.
Since MT7620 is really ancient hardware that likely only has few users left,
I don't expect that anybody will invest a significant amount of time to track
down the real cause. Because of that, let's disable CONFIG_LIST_HARDENED on
this target only, and leave it enabled on all other platforms.
Fixes: #16396
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Jonas Jelonek [Tue, 15 Oct 2024 18:52:35 +0000 (20:52 +0200)]
uboot-mediatek: add noncached_set_region prototype to fix build
Building uboot-mediatek fails with GCC-14, uboot v2024.10 and
CONFIG_SYS_NONCACHED_MEMORY defined with error:
cmd/cache.c: In function 'do_dcache':
cmd/cache.c:57:25: error: implicit declaration of function
'noncached_set_region' [-Wimplicit-function-declaration]
This is caused by upstream commit
7d6cee2cd0e2e2507aca1e3a6fe0e2cb241a116e
("cmd: cache: Remove weak functions") as this removes weak functions in
favor of arch-specific definitions.
This patch adds the function prototype for `noncached_set_region` to
arch-specific header for ARM. It also adds an include in cmd/cache.c to
make the function available there.
Fixes: #16697
Fixes: f8c22c9bff ("uboot-mediatek: update to U-Boot 2024.10")
Signed-off-by: Jonas Jelonek <jelonek.jonas@gmail.com>
[@dangowrt refreshed patch]
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Daniel Golle [Tue, 15 Oct 2024 23:10:28 +0000 (00:10 +0100)]
mediatek: mt7622: add netdev rename preinit script
Add preinit script to rename network interfaces according to the
label provided in Device Tree.
Fixes: b6d8297510 ("mediatek: mt7622: add Adtran SmartRG SDG-841t6 device")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Chukun Pan [Fri, 20 Sep 2024 15:10:26 +0000 (23:10 +0800)]
mediatek: filogic: reorder alphabetically
Reorder scripts to keep alphabetical order.
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
Chukun Pan [Thu, 19 Sep 2024 15:10:18 +0000 (23:10 +0800)]
mediatek: filogic: fix network config for mt7986b-rfb
Fix the network configuration according to the device tree.
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
Daniel Golle [Tue, 15 Oct 2024 20:15:19 +0000 (21:15 +0100)]
generic: fix kernel version and ordering of Aquantia backports
Two patches declared as accepted in v6.13 were already accepted for
v6.12. Fix filenames and order of patches applied.
Reported-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Fixes: 8cc049cec2 ("generic: phy: aquantia: move accepted patches to backport-6.6")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Daniel Golle [Mon, 7 Oct 2024 14:33:21 +0000 (15:33 +0100)]
mediatek: use NVMEM framework on all Adtran devices
Use NVMEM framework to assign MAC addresses and WiFi EEPROM data on
all Adtran SmartRG devices.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Daniel Golle [Sat, 5 Oct 2024 17:22:20 +0000 (18:22 +0100)]
mediatek: mt7622: add Adtran SmartRG SDG-841t6 device
Specification
SoC: MediaTek MT7622A (2x Cortex-A53)
RAM: NANYA NT5CC256M16ER-EK (512 MiB)
MMC: Kioxia THGBMNG5D1LBAIT (4 GiB)
ETH0: Intel/MaxLinear GPY211 (2500M/1000M/100M/10M)
ETH1: Lantiq/Intel/MaxLinear PEF7071/GPY111 (1000M/100M/10M)
WLAN0: MediaTek MT7915E + MT7975D 2T2R 802.11bgn/ax (2.4G)
2T2R 802.11an/ac/ax (5G L)
WLAN1: MediaTek MT7915E + MT7975A 4T4R 802.11an/ac/ax (5G H)
BT: BT5 provided by MT7915E+MT7975D (missing firmware)
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Daniel Golle [Sat, 5 Oct 2024 20:43:48 +0000 (21:43 +0100)]
mediatek: add driver for Adtran MFGINFO NVMEM layout
This driver allows retrieving MAC addresses and other factory information
via the NVMEM framework on Adtran devices.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Daniel Golle [Fri, 4 Oct 2024 13:04:25 +0000 (14:04 +0100)]
mediatek: mt7622: enable HWMON in kernel config
Building HWMON as module prevents some other drivers from getting built
into the kernel, e.g. mxl-gpy. Always enable HWMON and also set
THERMAL_HWMON.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Daniel Golle [Sat, 5 Oct 2024 21:21:17 +0000 (22:21 +0100)]
generic: net: phy: intel-way: add support for PHY LEDs
Add driver support for PHY LEDs for MaxLinear/Intel/Lantiq XWAY
Ethernet PHYs.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Daniel Golle [Tue, 1 Oct 2024 23:35:07 +0000 (00:35 +0100)]
generic: net: phy: mxl-gpy: add support for PHY LEDs
Add driver support for PHY LEDs for MaxLinear/Intel GPY Ethernet PHYs.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Daniel Golle [Sat, 5 Oct 2024 21:19:43 +0000 (22:19 +0100)]
generic: phy: aquantia: correctly describe LED polarity
Backport newly introduced support for 'active-high' property and use
it to correctly implement polarity assignment for Aquantia PHY LEDs.
Previously the 'active-low' property was used to switch a LED PIN to
active-high ("drive VDD" in Aquantia-speak) mode.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Daniel Golle [Tue, 15 Oct 2024 16:39:13 +0000 (17:39 +0100)]
generic: phy: aquantia: move accepted patches to backport-6.6
Move patches accepted upstream from pending-6.6 to backport-6.6.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Daniel Golle [Fri, 11 Oct 2024 03:42:09 +0000 (04:42 +0100)]
generic: net: phy: be more conservative about MAC interface selection
Only add SerDes interface modes at lower speeds to host_interfaces.
Fixes: 5281033831 ("generic: net: phy: use all SerDes MAC interface modes")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Stijn Tintel [Tue, 15 Oct 2024 09:13:35 +0000 (12:13 +0300)]
qoriq: add squashfs to FEATURES
The snapshot builds for qoriq only contain ext4 images. Add squashfs to
FEATURES to also have the buildbots build squashfs images.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Felix Fietkau [Tue, 15 Oct 2024 08:21:47 +0000 (10:21 +0200)]
kernel: fix mtk_eth_soc memory corruption issue on fq dma init
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Stijn Tintel [Mon, 14 Oct 2024 21:23:36 +0000 (00:23 +0300)]
qoriq: add missing kernel config symbol
Dropping the source-only flag from qoriq and adding it to the buildbots
exposed a missing kernel config symbol: CONFIG_DRM_OFDRM. Addd it as
disabled to the qoriq kernel config, as the only device currently
supported in the qoriq target does not have any display hardware.
Reported-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Michael Pratt [Sat, 12 Oct 2024 18:55:04 +0000 (14:55 -0400)]
tools/ninja: update to 1.12.1
Update to the most recent stable release,
including a new job scheduler and bug fixes.
Backport a patch to assist in reworking jobserver support.
The original patch for jobserver support requires reworking
due to the function CanRunMore() and its usage
being significantly changed, including the return
becoming an integer instead of a boolean.
AcquireToken() must now be used in CanRunMore()
in order to quantify how much the job searching loop
is able to run at any time, and in order to do so
CanRunMore() cannot be a constant function anymore.
Added:
- 010-backport-gtest.patch
Manually Adjust:
- 100-make_jobserver_support.patch
Signed-off-by: Michael Pratt <mcpratt@pm.me>
Link: https://github.com/openwrt/openwrt/pull/16693
Signed-off-by: Robert Marko <robimarko@gmail.com>
Michael Pratt [Fri, 2 Aug 2024 08:02:58 +0000 (04:02 -0400)]
tools/ninja: use existing ninja to build ninja
Add methods to skip the building and execution of Ninja by python
in order to allow Make to execute Ninja after the configure script.
This allows the user to build Ninja only once
if they already have an older version of Ninja built.
It also allows the user to test the jobserver functionality
by having Ninja built twice (clean then compile).
Signed-off-by: Michael Pratt <mcpratt@pm.me>
Link: https://github.com/openwrt/openwrt/pull/16693
Signed-off-by: Robert Marko <robimarko@gmail.com>
Michael Pratt [Mon, 22 Jul 2024 19:51:12 +0000 (15:51 -0400)]
tools/ninja: cleanup Makefile
Use default CXXFLAGS and LDFLAGS variables.
Directly add --verbose flag without a variable.
Split up lines for script arguments.
Delete unnecessary lines.
Signed-off-by: Michael Pratt <mcpratt@pm.me>
Link: https://github.com/openwrt/openwrt/pull/16693
Signed-off-by: Robert Marko <robimarko@gmail.com>
Robert Marko [Mon, 14 Oct 2024 11:02:24 +0000 (13:02 +0200)]
mvebu: cortex-a9: add upgrade methode to nas1dual
The blamed commit adds a upgrade recipe for nas1dual to specify the
firmware partition name, but does not actually include the recipe that
will be called.
Since it previously relied on the default one, add that one.
Fixes: d21720fa90c8 ("mvebu: fix default partition name")
Link: https://github.com/openwrt/openwrt/pull/16704
Signed-off-by: Robert Marko <robimarko@gmail.com>
Stijn Tintel [Sun, 13 Oct 2024 13:12:58 +0000 (16:12 +0300)]
xdp-tools: bump to 1.4.3
Release notes:
https://github.com/xdp-project/xdp-tools/releases/tag/v1.4.3
Remove upstreamed patch
023-libxdp-fix-compilation-on-multiarch-systems.patch.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Stijn Tintel [Sun, 13 Oct 2024 17:21:44 +0000 (20:21 +0300)]
libbpf: bump to 1.4.6
Release notes:
https://github.com/libbpf/libbpf/releases/tag/v1.4.6
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Stijn Tintel [Sun, 13 Oct 2024 19:25:10 +0000 (22:25 +0300)]
qoriq: drop source-only flag
While the qoriq target currently supports only one device, the
WatchGuard Firebox M300, the feedback from people using it is that it's
a great bang for the buck. Additionally, people suggest having no
snapshots available hurts adoption.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Rosen Penev [Sun, 1 Sep 2024 22:33:43 +0000 (15:33 -0700)]
qoriq: use nvmem for MAC addresses
Userspace handling is deprecated.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16308
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Peter Körner [Fri, 4 Oct 2024 20:50:49 +0000 (22:50 +0200)]
rtl83xx: fix typo
Removes an unwanted special character in a debug-message.
Signed-off-by: Peter Körner <peter@mazdermind.de>
Boris Krasnovskiy [Sun, 13 Oct 2024 00:01:57 +0000 (20:01 -0400)]
mvebu: fix sysupgrade failure
Linksys devices do no pass $cmd at all.
Fixes: #16148
Fixes: 715634e6d144 ("base-files: upgrade: nand: use "cmd" argument for extracting command")
Signed-off-by: Boris Krasnovskiy <borkra@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16690
Signed-off-by: Robert Marko <robimarko@gmail.com>
Boris Krasnovskiy [Sat, 12 Oct 2024 23:57:16 +0000 (19:57 -0400)]
mvebu: fix default partition name
The firmware partition name is specifc to ipTIME NAS1dual and should not be
set globally.
Fixes: #16148
Fixes: 6ff970bb51f5 ("mvebu: add support for ipTIME NAS1dual")
Signed-off-by: Boris Krasnovskiy <borkra@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16690
Signed-off-by: Robert Marko <robimarko@gmail.com>
Felix Fietkau [Sun, 6 Oct 2024 15:43:23 +0000 (17:43 +0200)]
mac80211: fix letting drivers iterate over keys
Skip non-uploaded keys to avoid corner cases
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Jack Sun [Sat, 12 Oct 2024 15:36:17 +0000 (23:36 +0800)]
tools/cmake: update to 3.30.5
Release notes: https://cmake.org/cmake/help/latest/release/3.30.html
Signed-off-by: Jack Sun <sunjiazheng321521@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16657
Signed-off-by: Robert Marko <robimarko@gmail.com>
Daniel Golle [Mon, 7 Oct 2024 17:31:58 +0000 (18:31 +0100)]
uboot-mediatek: update to U-Boot 2024.10
Update to latest U-Boot release.
Patches refreshed and fixed when needed.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Rosen Penev [Sat, 24 Aug 2024 19:35:03 +0000 (12:35 -0700)]
ramips: use nvmem to get mikrotik mac
73a9f9f857947bc63fef1aefb7e2e4b906fb9d2b added support. Let's use it.
Calibration data is not yet supported.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16256
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Magnus Sandin [Mon, 7 Oct 2024 20:39:38 +0000 (20:39 +0000)]
mediatek: ASUS TUF-AX6000: Add Green & Red LEDs
Beside the already existing control of the
Blue cover LED, this will also add the
Green and the Red cover LEDS available in the
Asus TUF-AX6000.
Signed-off-by: Magnus Sandin <magnus.sandin@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16632
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Yanase Yuki [Tue, 8 Oct 2024 11:02:25 +0000 (20:02 +0900)]
toolchain/binutils: remove old versions
Reduce supported versions to 3.
Since 2.40 is supported by previous release, this commit
keeps it.
Signed-off-by: Yanase Yuki <dev@zpc.st>
Link: https://github.com/openwrt/openwrt/pull/16597
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Linus Walleij [Mon, 7 Oct 2024 10:12:40 +0000 (12:12 +0200)]
linux: generic: dsa: mv88e6xx: Drop obsolete patch
As described by Tobias Waldekranz this patch is obsolete
and the issue is already fixed in the upstream kernels we
are using.
Link: http://lists.openwrt.org/pipermail/openwrt-devel/2024-October/043238.html
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Linus Walleij [Fri, 9 Aug 2024 09:45:04 +0000 (11:45 +0200)]
linux: generic: net: dsa: mv88e6xxx LED support
This solution that is needed for some routers to provide proper
LED activity when controlled directly by the MV88E6xxx switch,
has just been merged in upstream Linux.
Make this patch 901 as other backports from earlier kernels
are in patch 896 and this is the first free number after
that.
Patch offsets in pending patches are augmented as part of
the refresh.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Shiji Yang [Mon, 7 Oct 2024 15:21:16 +0000 (23:21 +0800)]
ramips: remove useless cs gpio code for rt2800 SPI driver
The SPI driver framework can handle it automatically in
spi.c:spi_setup():spi_set_cs():gpiod_set_value_cansleep().
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
Link: https://github.com/openwrt/openwrt/pull/16636
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Matteo Croce [Sat, 28 Sep 2024 22:41:23 +0000 (00:41 +0200)]
scripts/download.pl: use perl builtins instead of system()
Perl natively supports renaming files and create directories.
Do it without calling system().
Signed-off-by: Matteo Croce <teknoraver@meta.com>
Link: https://github.com/openwrt/openwrt/pull/16542
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Itay Shoshani [Sat, 12 Oct 2024 09:56:35 +0000 (09:56 +0000)]
wireless-regdb: Update to version 2024.10.07
b66b9a1 wireless-regdb: update regulatory database based on preceding changes
5097b4a wireless-regdb: Update regulatory info for Tanzania (TZ) for 2024
29633a6 wireless-regdb: Update regulatory info for Pakistan (PK) for 2024
b44edb2 wireless-regdb: Update regulatory info for Serbia (RS) for 2024
dbfae47 Revert "wireless-regdb: Update regulatory info for Serbia (SR) for 2024"
8e3d27c wireless-regdb: Correct regulatory rules of 6GHz frequency for Türkiye (TR)
8760bc3 wireless-regdb: Update regulatory info for Honduras (HN) for 2023
3ba2c53 wireless-regdb: Update regulatory info for Israel (IL) for 2021
83c175c wireless-regdb: Update regulatory info for Kuwait (KW) for 2022
388c80c wireless-regdb: Update regulatory info for Serbia (SR) for 2024
bf55ed4 wireless-regdb: Add .b4-config
3afe172 wireless-regdb: Update .gitignore
3b34761 wireless-regdb: Correct regulatory rules for China (CN)
003c282 wireless-regdb: Update regulatory info for Philippines (PH) on 6GHz
21fcb86 wireless-regdb: Update regulatory info for Guatemala (GT) for 2020
158f105 wireless-regdb: Update regulatory info for Bahrain (BH) for 2024
218d146 wireless-regdb: Add regulatory info for Namibia (NA) for 2023
aad0c26 wireless-regdb: Update regulatory info for Togo (TG) for 2022
983f551 wireless-regdb: Update regulatory info for El Salvador (SV) on 6GHz
58575b4 wireless-regdb: Update regulatory info for Peru (PE) on 6GHz
bad3985 wireless-regdb: Update regulatory info for New Zealand (NZ) for 2022
c7d1083 wireless-regdb: Update regulatory info for Qatar (QA) on 6GHz
Signed-off-by: Itay Shoshani <itai.sho@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16678
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Hauke Mehrtens [Thu, 10 Oct 2024 20:26:56 +0000 (22:26 +0200)]
gdb: Remove MIPS NSIG patch
This bug was fixed in the libc:
https://sourceware.org/bugzilla/show_bug.cgi?id=14523
https://git.busybox.net/uClibc/commit/?id=
2da958760f798224065508431787e3a83b7fe2ae
https://git.musl-libc.org/cgit/musl/commit/?id=
7c440977db9444d7e6b1c3dcb1fdf4ee49ca4158
Link: https://github.com/openwrt/openwrt/pull/16665
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Hauke Mehrtens [Thu, 10 Oct 2024 20:20:49 +0000 (22:20 +0200)]
gdb: Remove upstreamed SIGINT patch
The problem was fixed upstream, see:
https://sourceware.org/bugzilla/show_bug.cgi?id=18945
https://sourceware.org/git/?p=binutils-gdb.git;a=commitdiff;h=
4c35c4c6a779c79e456b7a5311f74aafc9026bd5
Link: https://github.com/openwrt/openwrt/pull/16665
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Hauke Mehrtens [Thu, 10 Oct 2024 20:13:40 +0000 (22:13 +0200)]
gdb: Update to version 15.2
See news file for changes:
https://sourceware.org/git/gitweb.cgi?p=binutils-gdb.git;a=blob_plain;f=gdb/NEWS;hb=gdb-15.1-release
Link: https://github.com/openwrt/openwrt/pull/16665
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Hauke Mehrtens [Thu, 10 Oct 2024 20:13:57 +0000 (22:13 +0200)]
toolchain: gdb: Update to version 15.2
See news file for changes:
https://sourceware.org/git/gitweb.cgi?p=binutils-gdb.git;a=blob_plain;f=gdb/NEWS;hb=gdb-15.1-release
This requires a C++17 compiler compatible compiler.
Link: https://github.com/openwrt/openwrt/pull/16665
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Aleksander Jan Bajkowski [Sat, 12 Oct 2024 18:28:29 +0000 (20:28 +0200)]
lantiq: ase: disable adm6996 and swconfig
The ase subtarget supports two devices. ALLNET ALL0333CJ has one
Ethernet port and uses only the built-in MAC and PHY. The second
device is the Netgear DGN1000, which uses an AR8216 switch.
The driver for the adm6996 switch was probably accidentally
enabled instead of the ar8216 in commit that restores ase support
9b321bc60de3 ("lantiq: add Amazon-SE subtarget").
Before removing the ase subtarget, only ar8216 was enabled
c82183639512 ("lantiq: remove unmaintained code").
Reduce uncompressed kernel size by 15.6 kB.
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
Link: https://github.com/openwrt/openwrt/pull/15332
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Aleksander Jan Bajkowski [Sat, 12 Oct 2024 18:27:08 +0000 (20:27 +0200)]
lantiq: ase: refresh config
This was done by executing these command:
$ make kernel_oldconfig CONFIG_TARGET=subtarget
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
Link: https://github.com/openwrt/openwrt/pull/15332
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Shiji Yang [Sat, 5 Oct 2024 04:22:12 +0000 (12:22 +0800)]
ppp: clean up makefile
The latest ppp version seems to no longer require these ancient
build fixes.
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
Link: https://github.com/openwrt/openwrt/pull/16605
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Shiji Yang [Fri, 4 Oct 2024 14:40:11 +0000 (22:40 +0800)]
ppp: remove discovery phase timeout hack patch
In the original code, the entire time delay of the discovery phase
is only 5+5x2+5x2x2 = 35s. Increasing timeout may be necessary if
discovery phase fails on first attempt. There is a chance to fix
the "Timeout waiting for PADO packets" issue by removing this patch.
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
Link: https://github.com/openwrt/openwrt/pull/16605
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Shiji Yang [Fri, 4 Oct 2024 14:25:52 +0000 (22:25 +0800)]
ppp: remove uClibc wtmp hack patch
The uClibc library support was removed since commit:
57fe7d5401e3 ("toolchain: remove uClibc install stuff")
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
Link: https://github.com/openwrt/openwrt/pull/16605
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Shiji Yang [Sun, 29 Sep 2024 02:39:56 +0000 (10:39 +0800)]
ppp: update to 2.5.1
ChangeLog:
https://github.com/ppp-project/ppp/blob/ppp-2.5.1/ChangeLog
Suppressed patches:
010-use_target_for_configure.patch [1]
510-pptp_compile_fix.patch [2]
520-u_int_bsd_fix.patch [3]
Upstreamed patches:
330-retain_foreign_default_routes.patch [4]
521-remove_unused_openssl_dep.patch [5]
[1] https://github.com/ppp-project/ppp/commit/
e48a9b5de46b6d3a7fda98ac64de56092471ab98
[2] Merged into "500-add-pptp-plugin.patch"
[3] https://github.com/ppp-project/ppp/commit/
797cdae57c27ed74a5ec3b4675f31f2c6cfc98ae
[4] https://github.com/ppp-project/ppp/commit/
9856f47063c01096fe6649a21be9a021e42a45fe
[5] https://github.com/ppp-project/ppp/commit/
59342ab622a96393d25d3a2f0592c8675e771295
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
Link: https://github.com/openwrt/openwrt/pull/16605
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Sergey Ivanov [Sat, 17 Jun 2023 07:20:42 +0000 (10:20 +0300)]
ppp: update to 2.5.0
ChangeLog:
https://github.com/ppp-project/ppp/blob/ppp-2.5.0/ChangeLog
Upstreamed patches:
120-debian_ipv6_updown_option.patch [1]
133-fix_sha1_include.patch [2]
140-pppd-Fix-compilation-with-older-glibc-or-kernel-head.patch [3]
141-Expand-byte-count-statistics-to-64-bits-298.patch [4]
142-pppd-Add-support-for-registering-ppp-interface-via-L.patch [5]
143-pppd-Workaround-for-generating-ppp-unit-id-on-Linux-.patch [6]
144-pppd-Retry-registering-interface-when-on-rtnetlink-E.patch [7]
Suppressed patches:
200-makefile.patch [8]
201-mppe_mppc_1.1.patch [9]
203-opt_flags.patch [10]
300-filter-pcap-includes-lib.patch [11]
511-pptp_cflags.patch [12]
600-Revert-pppd-Use-openssl-for-the-DES-instead-of-the-l.patch [13]
610-pppd_compile_fix.patch [14]
[1] https://github.com/ppp-project/ppp/commit/
7f8c1a1f8e486b232340fd9a0a19c5d34f1c5ae0
[2] https://github.com/ppp-project/ppp/commit/
ba7f7e053daae846a54a1d08d3d133a5f1266ace
[3] https://github.com/ppp-project/ppp/commit/
98ec18f098e5ef68e3a8cc6954fcaf5a7fb8b7be
[4] https://github.com/ppp-project/ppp/commit/
81ad945630120cc1c27c8bb00503be42b76ff202
[5] https://github.com/ppp-project/ppp/commit/
4a54e34cf5629f9fed61f0b7d69ee3ba4d874bc6
[6] https://github.com/ppp-project/ppp/commit/
44609bfc974bdafc0316d069aabf5e2903efa805
[7] https://github.com/ppp-project/ppp/commit/
089687fbcc6524809ae9f4b2f8145fe3c2a91147
[8] enable_eaptls=no, with_pcap=no, HAVE_CRYPT_H=1 in configure
[9] enable_microsoft_extensions=yes, MPPC support is removed.
[10] fPIC ignored so far
[11] done by autotools
[12] in main patch for pptp plugin
[13] with_openssl=no, already in upstream ppp-des.c
[14] with_static_pcap=yes from patch 310
Signed-off-by: Sergey Ivanov <icegood1980@gmail.com>
* Fix package hash.
* Fix multilink variant build.
* Fix some compile errors.
* Some code format fixes.
* Refactor commit message.
* Rebase git and fix conflicts.
Co-authored-by: Shiji Yang <yangshiji66@qq.com>
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
Link: https://github.com/openwrt/openwrt/pull/16605
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Petr Štetiar [Sat, 28 Sep 2024 13:27:19 +0000 (13:27 +0000)]
openwrt-keyring: add apk public key for signing of package indexes
apk/openwrt-snapshots.pem contains Elliptic Curve based public key which
is going to be used for signing of apk's package.adb package indexes
after the builds using `apk adbsign --sign-key <key> packages.adb`
command on the buildbot.
References: https://github.com/openwrt/buildbot/pull/46
Link: https://github.com/openwrt/openwrt/pull/16539
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Markus Stockhausen [Fri, 11 Oct 2024 19:11:43 +0000 (15:11 -0400)]
realtek: scripts: fix error in belkin-header
For some reason the new belkin-header.py script works without issues
in a local Fedora build environment. In the OpenWrt build pipeline it
produces the following errors:
Traceback (most recent call last):
File "/builder/shared-workdir/build/scripts/belkin-header.py", line 92, in <module>
head = create_header(buf, args.belkin_header, args.belkin_model)
File "/builder/shared-workdir/build/scripts/belkin-header.py", line 68, in create_header
head[28:29] = VERSION1.to_bytes(1)
TypeError: to_bytes() missing required argument 'byteorder' (pos 2)
This may be related due to different python version. Fix this by
handing over the needed parameters
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/16667
Signed-off-by: Robert Marko <robimarko@gmail.com>
Felix Fietkau [Fri, 11 Oct 2024 18:03:23 +0000 (20:03 +0200)]
mt76: update to Git HEAD (2024-10-11.1)
ecca0e77b4bc wifi: mt76: mt7915: fix omac index assignment after hardware reset
Signed-off-by: Felix Fietkau <nbd@nbd.name>
John Audia [Thu, 10 Oct 2024 21:20:15 +0000 (17:20 -0400)]
kernel: bump 6.6 to 6.6.56
Changelog: https://cdn.kernel.org/pub/linux/kernel/v6.x/ChangeLog-6.6.56
No patches needed a rebase
Build system: x86/64
Build-tested: x86/64/AMD Cezanne, flogic/xiaomi_redmi-router-ax6000-ubootmod, ramips/tplink_archer-a6-v3
Run-tested: x86/64/AMD Cezanne, flogic/xiaomi_redmi-router-ax6000-ubootmod, ramips/tplink_archer-a6-v3
Signed-off-by: John Audia <therealgraysky@proton.me>
Link: https://github.com/openwrt/openwrt/pull/16655
Signed-off-by: Nick Hainke <vincent@systemli.org>
John Audia [Thu, 10 Oct 2024 20:06:27 +0000 (16:06 -0400)]
kernel: bump 6.6 to 6.6.55
Changelog: https://cdn.kernel.org/pub/linux/kernel/v6.x/ChangeLog-6.6.55
Added the following default ksym to target/linux/generic/config-6.6:
CONFIG_PROC_MEM_ALWAYS_FORCE=y
# CONFIG_PROC_MEM_FORCE_PTRACE is not set
# CONFIG_PROC_MEM_NO_FORCE is not set
Removed upstreamed:
generic/backport-6.6/780-23-v6.12-r8169-Fix-spelling-mistake-tx_underun-tx_underrun.patch[1]
generic/backport-6.6/780-25-v6.12-r8169-add-tally-counter-fields-added-with-RTL8125.patch[2]
generic/pending-6.6/684-gso-fix-gso-fraglist-segmentation-after-pull-from-fr.patch[3]
lantiq/patches-6.6/0025-v6.12-net-ethernet-lantiq_etop-fix-memory-disclosure.patch[4]
Manually rebased:
bcm27xx/patches-6.6/950-0086-Main-bcm2708-bcm2709-linux-port.patch
bcm27xx/patches-6.6/950-0998-i2c-designware-Add-support-for-bus-clear-feature.patch
All other patches automatically rebased.
1. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v6.6.56&id=
f02fcb7283b1c25f7e3ae07d7a2c830e06eb1a62
2. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v6.6.56&id=
1c723d785adb711496bc64c24240f952f4faaabf
3. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v6.6.56&id=
af3122f5fdc0d00581d6e598a668df6bf54c9daa
4. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v6.6.56&id=
e66e38d07b31e177ca430758ed97fbc79f27d966
Build system: x86/64
Build-tested: x86/64/AMD Cezanne, flogic/xiaomi_redmi-router-ax6000-ubootmod, ramips/tplink_archer-a6-v3
Run-tested: x86/64/AMD Cezanne, flogic/xiaomi_redmi-router-ax6000-ubootmod, ramips/tplink_archer-a6-v3
Signed-off-by: John Audia <therealgraysky@proton.me>
Link: https://github.com/openwrt/openwrt/pull/16655
Signed-off-by: Nick Hainke <vincent@systemli.org>
Felix Fietkau [Fri, 11 Oct 2024 16:50:32 +0000 (18:50 +0200)]
mt76: update to Git HEAD (2024-10-11)
513bd7683746 Revert "wifi: mt76: mt7915: disable the second PCIe link for MT7915"
703c6b78c133 wifi: mt76: mt7915: firmware restart on devices with a second pcie link
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Christian Marangi [Fri, 11 Oct 2024 12:05:40 +0000 (14:05 +0200)]
generic: backport BLOCK OF support patch
Backport BLOCK OF support patch merged upstream and refresh pending
BLOCK patches.
This is a new way to declare partition table for BLOCK device (eMMC
currently supported) with the use of DTS.
Current pending patch are adapted to not cause regression with current
downstream implementation of a similar functionality.
Also enable the new OF_PARTITION config by default.
Link: https://github.com/openwrt/openwrt/pull/16663
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Shiji Yang [Fri, 11 Oct 2024 10:40:16 +0000 (18:40 +0800)]
ipq40xx: switch to zImage kernel for SKSpruce WIA3300-20
The bootloader can support zImage linux kernel which can decrease
the firmware image size.
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
Link: https://github.com/openwrt/openwrt/pull/16662
Signed-off-by: Robert Marko <robimarko@gmail.com>
Felix Fietkau [Fri, 11 Oct 2024 12:39:54 +0000 (14:39 +0200)]
netifd: update to Git HEAD (2024-10-06)
3c6265fdbd02 wireless: reload wireless device if any vif network bridge changes ifindex
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Tianling Shen [Wed, 9 Oct 2024 12:47:34 +0000 (20:47 +0800)]
uboot-rockchip: Update to 2024.10
Removed upstreamed patches.
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
Link: https://github.com/openwrt/openwrt/pull/16647
Signed-off-by: Nick Hainke <vincent@systemli.org>
Thomas Richard [Tue, 24 Sep 2024 16:27:16 +0000 (18:27 +0200)]
scripts/feeds: force kernel package scan after a target installation
When a target is installed from a feed, the linux kernel package is scanned
before the installation of this target.
If some kernel module packages are defined in this feeds at the target
level, there were not parsed during the scan of linux kernel package, as
the target didn't exist yet. So these kernel module packages don't exist.
Once the target is installed, clean the linux kernel packageinfo to force
the scan of the linux kernel package next time this script (or the make
command) is called.
Signed-off-by: Thomas Richard <thomas.richard@bootlin.com>
Link: https://patchwork.ozlabs.org/project/openwrt/patch/mailman.117548.1727195440.1280.openwrt-devel@lists.openwrt.org/
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Robert Marko [Thu, 10 Oct 2024 09:30:40 +0000 (11:30 +0200)]
realtek: refresh patches
CI is saying that patches need to be refreshed, so refresh them.
Link: https://github.com/openwrt/openwrt/pull/16653
Signed-off-by: Robert Marko <robimarko@gmail.com>
Felix Fietkau [Thu, 10 Oct 2024 08:49:53 +0000 (10:49 +0200)]
mt76: update to Git HEAD (2024-10-10)
86b41a32a5ac wifi: mac80211: don't use rate mask for offchannel TX either
82a452919f52 wifi: mac80211: handle ieee80211_radar_detected() for MLO
02c07fe539b4 wifi: mt76: mt7996: fix rx filter setting for bfee functionality
a902bfa6db2f wifi: mt76: mt7915: disable the second PCIe link for MT7915
a7d48cd3ed34 wifi: mt76: mt7915: reduce the number of command retries
0d8474602a9b wifi: mt76: mt7915: decrease timeout for commonly issued MCU commands
5f6051569639 wifi: mt76: mt7915: add module param to select 5 GHz or 6 GHz on MT7916
f5bccb122305 wifi: mt76: mt7996: fix invalid interface combinations
6a1199463fc8 wifi: mt76: mt7915: Fix an error handling path in mt7915_add_interface()
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Rosen Penev [Sat, 24 Aug 2024 00:39:17 +0000 (17:39 -0700)]
mpc85xx: handle MSM460 wifi mac in dts
Userspace handling is deprecated.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Robert Marko [Mon, 7 Oct 2024 13:07:39 +0000 (15:07 +0200)]
kernel: netdevices: add RmNet MAP support
RmNet driver provides a transport agnostic MAP (multiplexing and
aggregation protocol) support in embedded module. Module provides
virtual network devices which can be attached to any IP-mode
physical device.
This is commonly used on Qualcomm based modems for data aggregation.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Felix Fietkau [Wed, 9 Oct 2024 08:44:10 +0000 (10:44 +0200)]
kernel: backport upstream commit that allows leaving out .ndo_get_stats64
Fixes mac80211 backport device statistics.
Fixes: #16642
Signed-off-by: Felix Fietkau <nbd@nbd.name>
projects / openwrt / openwrt.git / log