John Crispin [Mon, 18 Aug 2014 13:09:14 +0000 (13:09 +0000)]
ar71xx: Fix 2.4G WiFi LED of the OpenMesh MR600 board
The OpenMesh MR600(v1) can only enable the 2.4G WiFi PHY LED through the
mini-PCIe device. Not configuring the LED pin inside the platform data
makes it impossible to configure it through any standard OpenWrt tool.
Signed-off-by: Sven Eckelmann <sven@open-mesh.com>
SVN-Revision: 42184
John Crispin [Mon, 18 Aug 2014 13:09:11 +0000 (13:09 +0000)]
lantiq: generate unique ARV7519RW22 firmware
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
SVN-Revision: 42183
John Crispin [Mon, 18 Aug 2014 13:09:08 +0000 (13:09 +0000)]
lantiq: add support for xrx200 firmware depending on soc type
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
SVN-Revision: 42182
John Crispin [Mon, 18 Aug 2014 13:08:59 +0000 (13:08 +0000)]
lantiq: export soc type
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
SVN-Revision: 42181
John Crispin [Mon, 18 Aug 2014 13:08:56 +0000 (13:08 +0000)]
lantiq: improve ARV7519RW22 support
- use full board name
- rename uboot-env partition
- add dsl_fw partition
- remove unneeded pinmux groups
- move gigabit ethernet to LAN
- load mac address from mtd
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
SVN-Revision: 42180
John Crispin [Mon, 18 Aug 2014 13:08:52 +0000 (13:08 +0000)]
ramips: add a workaround to fix failsafe on RT5350
Due to TCP connections not working when VLAN is disabled, this is
needed to get failsafe functional.
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
SVN-Revision: 42179
John Crispin [Mon, 18 Aug 2014 13:08:48 +0000 (13:08 +0000)]
ramips: enable additional GPIOs on HAME MPR-A1
According to the pcb tracing results[1] by anton.rad[2] MPR-A1s expose
6 unused GPIOs, only one of them working as configured in the current
DTS. This patch enables GPIO22-26.
Tested on hardware.
[1] http://i.imgur.com/kHVW2Ox.jpg
[2] https://forum.openwrt.org/viewtopic.php?pid=222698#p222698
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
SVN-Revision: 42178
John Crispin [Mon, 18 Aug 2014 13:08:45 +0000 (13:08 +0000)]
ar71xx: changed the EnGenius ESR900 mtdparts to match that of the ESR1750 since they have the same flash layout
Signed-off-by: Forest Crossman <cyrozap@gmail.com>
SVN-Revision: 42177
John Crispin [Mon, 18 Aug 2014 13:08:33 +0000 (13:08 +0000)]
ralink: add back the gpio_export_named() patch for 3.14
Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 42176
Florian Fainelli [Sat, 16 Aug 2014 18:09:31 +0000 (18:09 +0000)]
adm8668: revert changeset 34554
The conversion was not 100% correct and leads to u-boot failing to
verify the CRC, revert that change for now.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
SVN-Revision: 42170
Florian Fainelli [Sat, 16 Aug 2014 17:32:46 +0000 (17:32 +0000)]
ar7: remove 972-cpmac_fixup patch
This patch is causing more harm than good on most AR7 routers out there,
better have no manageable switch rather than no ethernet connection, at
least for now.
Fixes #16523, #5927
Signed-off-by: Florian Fainelli <florian@openwrt.org>
SVN-Revision: 42168
Hauke Mehrtens [Thu, 14 Aug 2014 21:22:17 +0000 (21:22 +0000)]
brcm47xx: image: update list of Netgear WNR* firmwares
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 42165
Hauke Mehrtens [Thu, 14 Aug 2014 21:21:27 +0000 (21:21 +0000)]
brcm47xx: fix brcm47xx.legacy build
we should check for ssb here.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 42164
Jonas Gorski [Wed, 13 Aug 2014 20:49:56 +0000 (20:49 +0000)]
dropbear: fix keepalive with putty
Don't send SSH_MSG_UNIMPLEMENTED for keepalive responses, which broke
at least putty.
Fixes #17522 / #17523.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 42162
Steven Barth [Wed, 13 Aug 2014 14:57:11 +0000 (14:57 +0000)]
netifd: assign ipv6-prefixes with length <64 with /64 on-link routes
SVN-Revision: 42161
Steven Barth [Wed, 13 Aug 2014 14:57:07 +0000 (14:57 +0000)]
odhcpd: improve DHCPv6-PD detection
SVN-Revision: 42160
Steven Barth [Wed, 13 Aug 2014 10:18:20 +0000 (10:18 +0000)]
ppp: enable IPv6CP by default
Signed-off-by: Steven Barth <steven@midlink.org>
SVN-Revision: 42158
Steven Barth [Tue, 12 Aug 2014 13:30:04 +0000 (13:30 +0000)]
odhcpd: multiple DHCPv4 improvements (thx Christian Mehlis)
Signed-off-by: Steven Barth <steven@midlink.org>
SVN-Revision: 42153
Jo-Philipp Wich [Tue, 12 Aug 2014 11:14:11 +0000 (11:14 +0000)]
package: fix segfault of iwinfo.scanlist("radio0").
This is a bug revealed in r41830.
First, the static variable `char nif[IFNAMSIZ]` of nl80211_phy2ifname()
would be zeroed out if the argument is "wlan0" or the like. This will
happen in the following call stack.
nl80211_get_scanlist("radio0", buf, len);
nl80211_phy2ifname("radio0") // return static var nif with content "wlan0"
nl80211_get_scanlist(nif, buf, len); // tail call
nl80211_get_mode(nif);
nl80211_phy2ifname(nif); // zero out nif
Later we try nl80211_ifadd("") which was supposed to create interface
"tmp.", but that won't happen because nl80211_msg() will put an invalid
ifidx 0 to the nlmsg.
Then iwinfo_ifup() and iwinfo_ifdown() would fail and happily
nl80211_get_scanlist() returned 0 and left *len undefined.
Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
SVN-Revision: 42151
Luka Perkov [Mon, 11 Aug 2014 20:35:15 +0000 (20:35 +0000)]
imx6: update kernel config
Signed-off-by: Luka Perkov <luka@openwrt.org>
SVN-Revision: 42149
Luka Perkov [Mon, 11 Aug 2014 20:35:13 +0000 (20:35 +0000)]
imx6: kernel: add GW5520 support
The GW5520 is a small form-factor single-board computer with the following
features:
* 70x100mm form-factor
* IMX6DL 800MHz SoC (IMX6Q optional)
* 512MB 32bit DDR3 SDRAM (up to 2GB optional)
* 256MB NAND FLASH (up to 2GB optional)
* Gateworks System Controller
* 2x front-panel Intel i210 GbE adapters with passive PoE support
* 2x MiniPCIe sockets with USB support
* 2x front-panel USB
* 1x rear-panel full-size HDMI connector
* 1x front-panel bi-color user LED
* 1x front-panel user pushbutton
* 1x rear-panel barrel jack for power
* 1x Application connector with:
* 2x TTL level UARTs
* 10x TTL level Digital IO
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
SVN-Revision: 42148
Luka Perkov [Mon, 11 Aug 2014 20:35:10 +0000 (20:35 +0000)]
imx6: kernel: add GW16083 Ethernet Expansion Mezzanine support
The GW16083 Ethernet Expansion Mezzanine adds the following to supported
Gateworks baseboards:
* 7-port Ethernet Switch
* 4x RJ45 ports (ENET1-4) supporing 802.11af/at PoE (with optional PoE module)
* 2x RJ45 ports or SFP module (ENET5-6) (auto-selected)
This series adds support for a phy driver that adds support for ENET5/ENET6
PHY adding initialization for those PHY's and a polling mechanism that detects
SFP insertion and configuration.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
SVN-Revision: 42147
Luka Perkov [Mon, 11 Aug 2014 20:35:06 +0000 (20:35 +0000)]
imx6: kernel: add GW16082 miniPCI Expansion Mezzanine support
The GW16082 miniPCI Expansion Mezzanine has the INTA/B/C/D IRQ's reversed
from the PCI standard. This will soon be resolved in the bootloader via
devicetree, but in the meantime this will work around the issue.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
SVN-Revision: 42146
Luka Perkov [Mon, 11 Aug 2014 20:35:04 +0000 (20:35 +0000)]
imx6: kernel: fix occasional link failure
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
SVN-Revision: 42145
Luka Perkov [Mon, 11 Aug 2014 20:35:02 +0000 (20:35 +0000)]
imx6: kernel: backport an upstream pci hang fix
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
SVN-Revision: 42144
Hauke Mehrtens [Mon, 11 Aug 2014 20:25:26 +0000 (20:25 +0000)]
bcm53xx: add b43 wifi support
Now it is possible to use b43 wifi.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 42143
Hauke Mehrtens [Mon, 11 Aug 2014 20:24:45 +0000 (20:24 +0000)]
bcm53xx: remove BCM4360 from PCI ids
bcma does not support this card and b43 hangs when probing this card.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 42142
Hauke Mehrtens [Mon, 11 Aug 2014 20:23:20 +0000 (20:23 +0000)]
mac80211: fix warning with kernel 3.14
This fixes a redefinition of net_get_random_once() warning.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 42141
Jo-Philipp Wich [Mon, 11 Aug 2014 18:15:18 +0000 (18:15 +0000)]
base-files: /lib/functions/network.sh: fix network_get_ipaddr6
When looking for the first ipaddr also consider the current prefix just
like network_get_ipaddrs6 does. If ipv6-address was empty the function
did not return the first ipaddr even if the list was non-empty.
fixes commit
83e9122f88a002871d5cdf421cf6aa6052b7e006
Signed-off-by: Henning Schild <henning@hennsch.de>
SVN-Revision: 42139
Jo-Philipp Wich [Mon, 11 Aug 2014 17:45:18 +0000 (17:45 +0000)]
firewall: fix potential NULL pointer access
Properly skip struct ifaddr entries with NULL ifa_addr, thanks Kostas Papadopoulos for reporting.
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>
SVN-Revision: 42138
Steven Barth [Mon, 11 Aug 2014 13:02:43 +0000 (13:02 +0000)]
dropbear: update to 2014.65
Signed-off-by: Steven Barth <steven@midlink.org>
SVN-Revision: 42131
Imre Kaloz [Mon, 11 Aug 2014 11:44:51 +0000 (11:44 +0000)]
add support for the NC-LINK SMART-300
Signed-off-by: Imre Kaloz <kaloz@openwrt.org>
SVN-Revision: 42130
Jonas Gorski [Mon, 11 Aug 2014 11:37:26 +0000 (11:37 +0000)]
brcm63xx: remove now obsolete board fixup code
Now that we migrated all users to dtb based detection, we can drop the
board fixup code.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 42129
Jonas Gorski [Mon, 11 Aug 2014 11:37:21 +0000 (11:37 +0000)]
brcm63xx: use dtb board detection for neufbox 4
This splits up neufbox 4 for now into two images, one for each OEM.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 42128
Jonas Gorski [Mon, 11 Aug 2014 11:37:17 +0000 (11:37 +0000)]
brcm63xx: use dtb board detection for NB6
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 42127
Jonas Gorski [Mon, 11 Aug 2014 11:37:14 +0000 (11:37 +0000)]
brcm63xx: use dtb board detection for HW556
This requires individual images for each board version for now.
Linux partition was shrunk to ensure writing thewrong image won't
erase wifi calibration data.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 42126
Jonas Gorski [Mon, 11 Aug 2014 11:37:09 +0000 (11:37 +0000)]
brcm63xx: replace CFEFIXUP usage with dtb based detection
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 42125
Jonas Gorski [Mon, 11 Aug 2014 11:37:04 +0000 (11:37 +0000)]
brcm63xx: move bcm96328avng to dtb detection
Use appended dtb for board detection for bcm96328avng.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 42124
Jonas Gorski [Mon, 11 Aug 2014 11:37:01 +0000 (11:37 +0000)]
brcm63xx: add support for registering parallel flash through dtb
Add the required nodes to the dtsi files and code to prevent double
registration from the board support code.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 42123
Jonas Gorski [Mon, 11 Aug 2014 11:36:59 +0000 (11:36 +0000)]
brcm63xx: add helpers for building cfe images with dtb
Add a helper for building images with dtb appended kernels.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 42122
Jonas Gorski [Mon, 11 Aug 2014 11:36:55 +0000 (11:36 +0000)]
brcm63xx: add support for attaching dtbs to lzma kernels
In preparation for switching to dtb based board identification, add
support for building lzma-loader and lzma cfe kernels with dtb
appended.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 42121
Jonas Gorski [Mon, 11 Aug 2014 11:36:53 +0000 (11:36 +0000)]
brcm63xx: add empty dtsi files for each of the supported SoCs
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 42120
Jonas Gorski [Mon, 11 Aug 2014 11:36:48 +0000 (11:36 +0000)]
brcm63xx: add and enable support for loading an appended dtb
Allow appending a dtb blob to the binary and use it for identifying the
board. Fall back to nvram based identification in case of no dtb passed.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 42119
Jonas Gorski [Mon, 11 Aug 2014 11:36:41 +0000 (11:36 +0000)]
brcm63xx: correctly export fallback sprom for brcm-wl
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
SVN-Revision: 42118
Jonas Gorski [Mon, 11 Aug 2014 11:36:38 +0000 (11:36 +0000)]
brcm63xx: make board patch context less ambiguous
Make it less likely for quilt/patch to put boards into the "wrong"
section.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 42117
Jonas Gorski [Mon, 11 Aug 2014 11:36:30 +0000 (11:36 +0000)]
brcm63xx: fix board patches offsets
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
[jogo fix 553-boards_probe_switch.patch]
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 42116
Jo-Philipp Wich [Mon, 11 Aug 2014 09:41:20 +0000 (09:41 +0000)]
firewall: implement selective conntrack flushing (#10225)
Utilize the new selective conntrack flushing facility to clear
out active conntrack entries referring to old IP addresses after
a firewall reload.
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>
SVN-Revision: 42114
Luka Perkov [Mon, 11 Aug 2014 09:21:05 +0000 (09:21 +0000)]
kernel: 3.14: refresh patches
Signed-off-by: Luka Perkov <luka@openwrt.org>
SVN-Revision: 42113
Jo-Philipp Wich [Mon, 11 Aug 2014 09:15:17 +0000 (09:15 +0000)]
build: enable PER_FEED_REPO by default
Enable the separate feed repositories by default to align custom builds with the repositories
available on the snapshot download server.
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>
SVN-Revision: 42112
Luka Perkov [Mon, 11 Aug 2014 08:44:48 +0000 (08:44 +0000)]
hostapd: fix some whitespaces
Signed-off-by: Luka Perkov <luka@openwrt.org>
SVN-Revision: 42111
Jonas Gorski [Sun, 10 Aug 2014 12:22:15 +0000 (12:22 +0000)]
brcm63xx: Add fallback sprom for A4001N
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 42110
Jonas Gorski [Sun, 10 Aug 2014 12:22:12 +0000 (12:22 +0000)]
brcm63xx: Add fallback sprom for HG520v
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 42109
Jonas Gorski [Sun, 10 Aug 2014 12:22:10 +0000 (12:22 +0000)]
brcm63xx: Add fallback sprom for P870HW-51a
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 42108
Jonas Gorski [Sun, 10 Aug 2014 12:22:08 +0000 (12:22 +0000)]
brcm63xx: Add fallback sprom for VR-3025un
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 42107
Jonas Gorski [Sun, 10 Aug 2014 12:22:05 +0000 (12:22 +0000)]
brcm63xx: Add fallback sprom for VR-3025u
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 42106
Jonas Gorski [Sun, 10 Aug 2014 12:22:02 +0000 (12:22 +0000)]
brcm63xx: Add fallback sprom for WAP-5813n
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 42105
Jonas Gorski [Sun, 10 Aug 2014 12:21:59 +0000 (12:21 +0000)]
brcm63xx: Add fallback sprom for AR-5381u
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 42104
Jonas Gorski [Sun, 10 Aug 2014 12:21:55 +0000 (12:21 +0000)]
brcm63xx: Add fallback sprom for AR-5387un
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 42103
Jonas Gorski [Sun, 10 Aug 2014 12:21:52 +0000 (12:21 +0000)]
brcm63xx: Add fallback sprom for A4001N1
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 42102
Jonas Gorski [Sun, 10 Aug 2014 12:21:48 +0000 (12:21 +0000)]
brcm63xx: Add fallback sprom for CT6373
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 42101
Jonas Gorski [Sun, 10 Aug 2014 12:21:44 +0000 (12:21 +0000)]
brcm63xx: Add fallback sprom for CT5365
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 42100
Jonas Gorski [Sun, 10 Aug 2014 12:21:39 +0000 (12:21 +0000)]
brcm63xx: Add fallback sprom for CT5361_CT5621
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 42099
Jonas Gorski [Sun, 10 Aug 2014 12:21:34 +0000 (12:21 +0000)]
brcm63xx: Add fallback sprom for Huawei HG553
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 42098
Jonas Gorski [Sun, 10 Aug 2014 12:21:30 +0000 (12:21 +0000)]
brcm63xx: Fix fallback sprom il0mac
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 42097
Jo-Philipp Wich [Sun, 10 Aug 2014 10:15:22 +0000 (10:15 +0000)]
netfilter: consider reply direction on selective flushing
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>
SVN-Revision: 42095
Jo-Philipp Wich [Sun, 10 Aug 2014 09:21:14 +0000 (09:21 +0000)]
netfilter: fix calls to nf_ct_iterate_cleanup() with Linux >= 3.13
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>
SVN-Revision: 42093
Jo-Philipp Wich [Sat, 9 Aug 2014 14:36:10 +0000 (14:36 +0000)]
netfilter: support /proc conntrack flushing of specific ip addresses
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>
SVN-Revision: 42092
Jo-Philipp Wich [Sat, 9 Aug 2014 13:04:17 +0000 (13:04 +0000)]
build: fix removal of old .ipk files with CONFIG_PER_FEED_REPO
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>
SVN-Revision: 42090
Hauke Mehrtens [Fri, 8 Aug 2014 23:10:16 +0000 (23:10 +0000)]
brcm47xx: fix reboot problem on BCM4705/BCM4785
This adds some code based on code from the Broadcom GPL tar to fix the
reboot problems on BCM4705/BCM4785. I tried rebooting my device for ~10
times and have never seen a problem. This reverts the changes in the
previous commit and adds the real fix as suggested by Rafał.
Setting bit 22 in Reg 22, sel 4 puts the BIU (Bus Interface Unit) into
async mode.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 42088
Hauke Mehrtens [Fri, 8 Aug 2014 22:59:45 +0000 (22:59 +0000)]
broadcom-wl: add default tx and rx antennas
This adds default tx and rx antennas, so that LuCI shows automatic as the default radio option for the antennas.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
SVN-Revision: 42085
Hauke Mehrtens [Fri, 8 Aug 2014 22:58:54 +0000 (22:58 +0000)]
broadcom-wl: add support for a8xx broadcom devices
Tested on Comtrend VR-3025u (brcm6368 + a8d6-43222).
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
SVN-Revision: 42084
Hauke Mehrtens [Fri, 8 Aug 2014 22:52:28 +0000 (22:52 +0000)]
brcm47xx: fix reboot problem on BCM4705/BCM4785
This adds some code based on code from the Broadcom GPL tar to fix the
reboot problems on BCM4705/BCM4785. I tried rebooting my device for ~10
times and have never seen a problem. This reverts the changes in the
previous commit and adds the real fix as suggested by Rafał.
Setting bit 22 in Reg 22, sel 4 puts the BIU (Bus Interface Unit) into
async mode.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 42083
Luka Perkov [Fri, 8 Aug 2014 21:03:14 +0000 (21:03 +0000)]
mkimage: update to 2014.07
Signed-off-by: Luka Perkov <luka@openwrt.org>
SVN-Revision: 42082
Luka Perkov [Fri, 8 Aug 2014 16:11:57 +0000 (16:11 +0000)]
imx6: update upstream patch
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Luka Perkov <luka@openwrt.org>
SVN-Revision: 42081
Luka Perkov [Fri, 8 Aug 2014 15:55:03 +0000 (15:55 +0000)]
uboot-kirkwood: bump to 2014.07
Signed-off-by: Luka Perkov <luka@openwrt.org>
SVN-Revision: 42080
Luka Perkov [Fri, 8 Aug 2014 15:14:26 +0000 (15:14 +0000)]
uboot-envtools: bump to 2014.07
Signed-off-by: Luka Perkov <luka@openwrt.org>
SVN-Revision: 42078
Luka Perkov [Fri, 8 Aug 2014 13:55:30 +0000 (13:55 +0000)]
kirkwood: drop 3.10 support
Signed-off-by: Luka Perkov <luka@openwrt.org>
SVN-Revision: 42077
Luka Perkov [Fri, 8 Aug 2014 13:55:29 +0000 (13:55 +0000)]
kirkwood: switch to 3.14
Signed-off-by: Luka Perkov <luka@openwrt.org>
SVN-Revision: 42076
Luka Perkov [Fri, 8 Aug 2014 13:38:31 +0000 (13:38 +0000)]
imx6: drop 3.10 support
Signed-off-by: Luka Perkov <luka@openwrt.org>
SVN-Revision: 42075
Luka Perkov [Fri, 8 Aug 2014 13:38:30 +0000 (13:38 +0000)]
imx6: switch to 3.14
Signed-off-by: Luka Perkov <luka@openwrt.org>
SVN-Revision: 42074
Luka Perkov [Fri, 8 Aug 2014 13:38:29 +0000 (13:38 +0000)]
imx6: update upstream patches
Signed-off-by: Luka Perkov <luka@openwrt.org>
SVN-Revision: 42073
Luka Perkov [Fri, 8 Aug 2014 13:38:27 +0000 (13:38 +0000)]
imx6: backport IMX6DL DVFS support from 3.15
This allows dynamic voltage and frequency scaling to work for IMX6DL CPU's.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
SVN-Revision: 42072
Luka Perkov [Fri, 8 Aug 2014 13:38:25 +0000 (13:38 +0000)]
imx6: drop ventana kernel/rootfs hack
In r41578 this was added in order to make default images bootable for the BB
release. We need more generic approach for this.
Signed-off-by: Luka Perkov <luka@openwrt.org>
SVN-Revision: 42071
Luka Perkov [Fri, 8 Aug 2014 13:38:22 +0000 (13:38 +0000)]
kernel: update 3.14 to 3.14.16
Signed-off-by: Luka Perkov <luka@openwrt.org>
SVN-Revision: 42070
Steven Barth [Fri, 8 Aug 2014 08:45:33 +0000 (08:45 +0000)]
odhcpd: avoid logspam in certain corner cases
SVN-Revision: 42067
Steven Barth [Fri, 8 Aug 2014 05:30:59 +0000 (05:30 +0000)]
odhcpd: write host-entries for all leased IPv6 addresses
SVN-Revision: 42065
Steven Barth [Fri, 8 Aug 2014 05:25:52 +0000 (05:25 +0000)]
cyassl: update to 3.1.0
SVN-Revision: 42063
Steven Barth [Fri, 8 Aug 2014 05:20:50 +0000 (05:20 +0000)]
polarssl: bump to 1.3.8
SVN-Revision: 42061
John Crispin [Thu, 7 Aug 2014 20:54:41 +0000 (20:54 +0000)]
openssl: another day another bug fix update
Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 42055
Hauke Mehrtens [Thu, 7 Aug 2014 20:22:00 +0000 (20:22 +0000)]
brcm47xx: activate high mem for mips74k in the config
It is still not working.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 42054
Hauke Mehrtens [Thu, 7 Aug 2014 20:21:11 +0000 (20:21 +0000)]
brcm47xx: 3.14: backport MIPS patches for early HIGHMEM support
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 42053
Hauke Mehrtens [Thu, 7 Aug 2014 20:20:38 +0000 (20:20 +0000)]
brcm47xx: 3.10: backport MIPS patches for early HIGHMEM support
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 42052
Felix Fietkau [Thu, 7 Aug 2014 19:30:36 +0000 (19:30 +0000)]
base-files: enable option to skip the netfilter "filter" table for established connection packets by default
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 42048
Felix Fietkau [Thu, 7 Aug 2014 19:30:33 +0000 (19:30 +0000)]
xtables-addons: remove version 1.x for old kernels
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 42047
Felix Fietkau [Thu, 7 Aug 2014 18:59:22 +0000 (18:59 +0000)]
kernel: add a patch to allow disabling processing of the netfilter "filter" table for established connection packets
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 42046
Felix Fietkau [Thu, 7 Aug 2014 18:59:18 +0000 (18:59 +0000)]
kernel: improve ipv4 netfilter optimization patch
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 42045
Felix Fietkau [Thu, 7 Aug 2014 18:59:15 +0000 (18:59 +0000)]
ar71xx: port missing ath79 machine entry for wndr3700 v4 to 3.14
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 42044
Steven Barth [Thu, 7 Aug 2014 18:07:37 +0000 (18:07 +0000)]
odhcpd: update hostfile more often
SVN-Revision: 42042
Jo-Philipp Wich [Thu, 7 Aug 2014 15:35:12 +0000 (15:35 +0000)]
build: consider sub-directories when deploying packages to image with CONFIG_PER_FEED_REPO (#17430)
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>
SVN-Revision: 42041
John Crispin [Thu, 7 Aug 2014 14:41:19 +0000 (14:41 +0000)]
ralink: add 3.14 support
Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 42040
projects / openwrt / staging / thess.git / log