Adrian Schmutzler [Mon, 19 Oct 2020 13:37:54 +0000 (15:37 +0200)]
ipq806x: remove support for kernel 4.19
The target uses 5.4 as default kernel since 04/2020.
Kernel 4.19 support is not really maintained anymore, and there has
been a lot of changes between 4.19 and 5.4 on this target. Despite,
new devices are typically added for 5.4 only anyway.
Thus, make maintaining of old stuff and reviewing of new stuff
easier by removing support for kernel 4.19.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Adrian Schmutzler [Mon, 19 Oct 2020 13:30:44 +0000 (15:30 +0200)]
ipq40xx: remove support for kernel 4.19
The target uses 5.4 as default kernel since 03/2020.
Kernel 4.19 support is not really maintained anymore, it does not
seem to be needed, and removing it will make upcoming driver
updates easier. Thus, remove it.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
John Crispin [Mon, 19 Oct 2020 12:47:45 +0000 (14:47 +0200)]
rtl838x: various fixes
* add d-link_dgs-1210-10p support
* make sure mips16 is disabled
* add a generic sub target
* add proper cflags
Signed-off-by: John Crispin <john@phrozen.org>
Hauke Mehrtens [Sun, 18 Oct 2020 12:26:55 +0000 (14:26 +0200)]
sunxi: Adapt U-Boot config to board rename
The board was renamed without changing the BUILD_DEVICES in the U-Boot
Makefile, this broken the build.
Fixes: 0830ae3a2fdf ("sunxi: Correct manufacturer name to Sinovoip")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Jayantajit Gogoi [Mon, 12 Oct 2020 18:51:34 +0000 (18:51 +0000)]
sunxi: add support for FriendlyARM NanoPi R1
Specification:
- CPU: Allwinner H3, Quad-core Cortex-A7 Up to 1.2GHz
- DDR3 RAM: 512MB/1GB
- Network:
10/100/1000M Ethernet x 1，
10/100M Ethernet x 1
- WiFi: 802.11b/g/n, with SMA antenna interface
- USB Host: Type-A x2
- MicroSD Slot x 1
- MicroUSB: for OTG and power input
- Debug Serial Port: 3Pin 2.54mm pitch pin-header
- LED:
nanopi:red:status
nanopi:green:wan
nanopi:green:lan
- KEY:
reset
- Power Supply: DC 5V/2A
Installation:
- Write the image to SD Card with dd
- Boot NanoPi from the SD Card
Signed-off-by: Jayantajit Gogoi <jayanta.gogoi525@gmail.com>
张鹏 [Fri, 16 Oct 2020 10:53:51 +0000 (12:53 +0200)]
ath79: add support for Qxwlan
E1700AC v2
E1700AC v2 based on Qualcomm/Atheros QCA9563 + QCA9880.
Specification:
- 750/400/250 MHz (CPU/DDR/AHB)
- 128 MB of RAM (DDR2)
- 8/16 MB of FLASH (SPI NOR)
- 3T3R 2.4 GHz
- 3T3R 5 GHz
- 2 x 10/1000M Mbps Ethernet (RJ45)
- 1 x MiniPCI-e
- 1 x SIM (3G/4G)
- 1 x USB 2.0 Port
- 5 x LED , 2 x Button(S8-Reset Buttun), 1 x power input
- UART (J5) header on PCB (115200 8N1)
Flash instruction:
1.Using tftp mode with UART connection and original LEDE image
- Configure PC with static IP 192.168.1.10 and tftp server.
- Rename "openwrt-ar71xx-generic-xxx-squashfs-sysupgrade.bin"
to "firmware.bin" and place it in tftp server directory.
- Connect PC with one of LAN ports, power up the router and press
key "Enter" to access U-Boot CLI.
- Use the following commands to update the device to LEDE:
run lfw
- After that the device will reboot and boot to LEDE.
- Wait until all LEDs stops flashing and use the router.
2.Using httpd mode with Web UI connection and original LEDE image
- Configure PC with static IP 192.168.1.xxx(2-255) and tftp server.
- Connect PC with one of LAN ports,press the reset button, power up
the router and keep button pressed for around 6-7 seconds, until
leds flashing.
- Open your browser and enter 192.168.1.1,You will see the upgrade
interface, select "openwrt-ar71xx-generic-xxx-squashfs-
sysupgrade.bin" and click the upgrade button.
- After that the device will reboot and boot to LEDE.
- Wait until all LEDs stops flashing and use the router.
Signed-off-by: 张鹏 <sd20@qxwlan.com>
[cut out of bigger patch, keep swconfig, whitespace fixes]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
张鹏 [Fri, 16 Oct 2020 10:42:15 +0000 (12:42 +0200)]
ath79: add support for Qxwlan E558 v2
Qxwlan E558 v2 is based on Qualcomm QCA9558 + AR8327.
Specification:
- 720/600/200 MHz (CPU/DDR/AHB)
- 128 MB of RAM (DDR2)
- 8/16 MB of FLASH (SPI NOR)
- 2T2R 2.4 GHz (QCA9558)
- 3x 10/100/1000 Mbps Ethernet (one port with PoE support)
- 4x miniPCIe slot (USB 2.0 bus only)
- 1x microSIM slot
- 5x LED (4 driven by GPIO)
- 1x button (reset)
- 1x 3-pos switch
- 1x DC jack for main power input (9-48 V)
- UART (JP5) and LEDs (J8) headers on PCB
Flash instruction:
1.Using tftp mode with UART connection and original LEDE image
- Configure PC with static IP 192.168.1.10 and tftp server.
- Rename "openwrt-ar71xx-generic-xxx-squashfs-sysupgrade.bin"
to "firmware.bin" and place it in tftp server directory.
- Connect PC with one of LAN ports, power up the router and press
key "Enter" to access U-Boot CLI.
- Use the following commands to update the device to LEDE:
run lfw
- After that the device will reboot and boot to LEDE.
- Wait until all LEDs stops flashing and use the router.
2.Using httpd mode with Web UI connection and original LEDE image
- Configure PC with static IP 192.168.1.xxx(2-255) and tftp server.
- Connect PC with one of LAN ports,press the reset button, power up
the router and keep button pressed for around 6-7 seconds, until
leds flashing.
- Open your browser and enter 192.168.1.1,You will see the upgrade
interface, select "openwrt-ar71xx-generic-xxx-squashfs-
sysupgrade.bin" and click the upgrade button.
- After that the device will reboot and boot to LEDE.
- Wait until all LEDs stops flashing and use the router.
Signed-off-by: 张鹏 <sd20@qxwlan.com>
[cut out of bigger patch, keep swconfig, whitespace adjustments]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
张鹏 [Wed, 14 Oct 2020 07:47:35 +0000 (15:47 +0800)]
ath79: add support for Qxwlan E750G v8
Qxwlan E750G v8 is based on Qualcomm QCA9344 + QCA9334.
Specification:
- 560/450/225 MHz (CPU/DDR/AHB)
- 128 MB of RAM (DDR2)
- 8/16 MB of FLASH (SPI NOR)
- 2T2R 2.4G GHz (AR9344)
- 2x 10/100/1000 Mbps Ethernet (one port with PoE support)
- 7x LED (6 driven by GPIO)
- 1x button (reset)
- 1x DC jack for main power input (9-48 V)
- UART (J23) and LEDs (J2) headers on PCB
Flash instruction:
1.Using tftp mode with UART connection and original LEDE image
- Configure PC with static IP 192.168.1.10 and tftp server.
- Rename "openwrt-ar71xx-generic-xxx-squashfs-sysupgrade.bin"
to "firmware.bin" and place it in tftp server directory.
- Connect PC with one of LAN ports, power up the router and press
key "Enter" to access U-Boot CLI.
- Use the following commands to update the device to LEDE:
run lfw
- After that the device will reboot and boot to LEDE.
- Wait until all LEDs stops flashing and use the router.
2.Using httpd mode with Web UI connection and original LEDE image
- Configure PC with static IP 192.168.1.xxx(2-255) and tftp server.
- Connect PC with one of LAN ports,press the reset button, power up
the router and keep button pressed for around 6-7 seconds, until
leds flashing.
- Open your browser and enter 192.168.1.1,You will see the upgrade
interface, select "openwrt-ar71xx-generic-xxx-squashfs-
sysupgrade.bin" and click the upgrade button.
- After that the device will reboot and boot to LEDE.
- Wait until all LEDs stops flashing and use the router.
Signed-off-by: 张鹏 <sd20@qxwlan.com>
[cut out of bigger patch, keep swconfig]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Felix Fietkau [Sat, 17 Oct 2020 09:15:32 +0000 (11:15 +0200)]
base-files: remove block2mtd checks from sysupgrade
This hasn't been used in a long time
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Felix Fietkau [Sat, 17 Oct 2020 09:14:11 +0000 (11:14 +0200)]
kernel: remove obsolete non-upstream block2mtd patches
Since block2mtd is not used for firmware images anymore, these patches
are no longer needed
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Felix Fietkau [Fri, 16 Oct 2020 19:42:11 +0000 (21:42 +0200)]
mac80211: fix memory leak on filtered powersave frames
After the status rework, ieee80211_tx_status_ext is leaking un-acknowledged
packets for stations in powersave mode.
To fix this, move the code handling those packets from __ieee80211_tx_status
into ieee80211_tx_status_ext
Reported-by: Tobias Waldvogel <tobias.waldvogel@gmail.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Adrian Schmutzler [Fri, 16 Oct 2020 20:58:44 +0000 (22:58 +0200)]
Revert "build: process variable exports from toplevel.mk only once"
This reverts commit
ef7c34c1d1beac6bca4a683a3a161dd12a81f7e8.
The commit seems to break all buildbots with messages like:
/builder/shared-workdir/build/include/toplevel.mk:15:
/builder/shared-workdir/build/include/toplevel-vars.mk: No such file or directory
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Felix Fietkau [Tue, 6 Oct 2020 11:39:58 +0000 (13:39 +0200)]
build: prevent excessive re-evaluation of PKG_VERSION
version_abbrev uses $(shell) and the ?= is causing make to run the command
over and over again, causing a significant build slowdown
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Felix Fietkau [Tue, 6 Oct 2020 10:37:51 +0000 (12:37 +0200)]
build: process variable exports from toplevel.mk only once
These run a lot of expensive shell calls, so redundant calls should be
avoided
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Felix Fietkau [Thu, 8 Oct 2020 11:44:33 +0000 (13:44 +0200)]
mediatek: rewrite flow offload code
The code is now much cleaner and works better than the old code.
Preparation for submitting it upstream (though with a different API)
Also add back MT7621 support and fix flow table coherence issues on
MT7622
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Daniel Golle [Fri, 16 Oct 2020 13:27:34 +0000 (14:27 +0100)]
config: clean up SELinux options
In order to make it easier for users to build with SELinux, have a
single option in 'Global build settings' to enable all necessary
kernel features, userland packages and build-system hooks.
Also add better descriptions and help messages while at it.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Daniel Golle [Sun, 11 Oct 2020 02:27:28 +0000 (03:27 +0100)]
selinux-policy: update to git tag v0.3
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Daniel Golle [Fri, 16 Oct 2020 00:51:13 +0000 (01:51 +0100)]
fstools: update to git HEAD
8e0f29a mount: remove support for legacy overlayfs before v2.3
0f8a443 mount: fix log format string and indentation
46a56d3 overlay: use precompiler macros for reoccuring path names
f25ab8a mount: apply SELinux labels before overlayfs mount
Total ipk size change (ipq40xx): +120b
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Daniel Golle [Sun, 11 Oct 2020 02:18:28 +0000 (03:18 +0100)]
policycoreutils: 'restorecon' is a 'setfiles' applet
Instead of duplicating the '/sbin/setfiles' binary, have
'/sbin/restorecon' as yet another alias for
'/sbin/policycoreutils-setfiles'.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Daniel Golle [Sat, 10 Oct 2020 22:04:13 +0000 (23:04 +0100)]
hostapd: ubus: add handler for wps_status and guard WPS calls
Expose WPS ubus API only if compiled with WPS support and add new
handler for wps_status call.
Also add '-v wps' option to check whether WPS support is present in
hostapd.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Peng Zhang [Wed, 14 Oct 2020 07:47:35 +0000 (15:47 +0800)]
ath79: add support for Qxwlan E750A v4
Qxwlan E750A v4 is based on Qualcomm QCA9344.
Specification:
- 560/450/225 MHz (CPU/DDR/AHB)
- 128 MB of RAM (DDR2)
- 8/16 MB of FLASH (SPI NOR)
- 2T2R 5G GHz (AR9344)
- 2x 10/100 Mbps Ethernet (one port with PoE support)
- 1x miniPCIe slot (USB 2.0 bus only)
- 7x LED (6 driven by GPIO)
- 1x button (reset)
- 1x DC jack for main power input (9-48 V)
- UART (J23) and LEDs (J2) headers on PCB
Flash instruction:
1.Using tftp mode with UART connection and original LEDE image
- Configure PC with static IP 192.168.1.10 and tftp server.
- Rename "openwrt-ar71xx-generic-xxx-squashfs-sysupgrade.bin"
to "firmware.bin" and place it in tftp server directory.
- Connect PC with one of LAN ports, power up the router and press
key "Enter" to access U-Boot CLI.
- Use the following commands to update the device to LEDE:
run lfw
- After that the device will reboot and boot to LEDE.
- Wait until all LEDs stops flashing and use the router.
2.Using httpd mode with Web UI connection and original LEDE image
- Configure PC with static IP 192.168.1.xxx(2-255) and tftp server.
- Connect PC with one of LAN ports,press the reset button, power up
the router and keep button pressed for around 6-7 seconds, until
leds flashing.
- Open your browser and enter 192.168.1.1,You will see the upgrade
interface, select "openwrt-ar71xx-generic-xxx-squashfs-
sysupgrade.bin" and click the upgrade button.
- After that the device will reboot and boot to LEDE.
- Wait until all LEDs stops flashing and use the router.
Signed-off-by: Peng Zhang <sd20@qxwlan.com>
[cut out of bigger patch, alter use of DEVICE_VARIANT, merge case
in 01_leds, use lower case for v4]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Adrian Schmutzler [Thu, 15 Oct 2020 15:54:31 +0000 (17:54 +0200)]
rtl838x: remove model name from LED labels
Like in the previous patches for various targets, this removes
the "devicename" from LED labels in rtl838x, as it's useless and
only creates complexity.
Since the target is fresh and so far only system LEDs were added,
this does not add a migration script.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Adrian Schmutzler [Thu, 15 Oct 2020 15:51:42 +0000 (17:51 +0200)]
rtl838x: move dts-v1 to DTSI
The syntax of the shared SoC DTSI file determines the DTS version,
so no need to repeat the "/dts-v1/;" identifier in every file.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Adrian Schmutzler [Thu, 15 Oct 2020 15:42:54 +0000 (17:42 +0200)]
sunxi: use wpad-basic-wolfssl for Sinovoip Banana Pi M2 Ultra
The idea of commit
a14f5bb4bd26 was to use wpad-basic-wolfssl
consistently throughout the whole trunk, so use it here as well.
Fixes: 50fdddae05f1 ("BPi-M2U kernel modules for onboard WiFi")
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
John Audia [Wed, 14 Oct 2020 11:54:05 +0000 (07:54 -0400)]
kernel: bump 5.4 to 5.4.71
All modifications made by update_kernel.sh
Build system: x86_64
Build-tested: ipq806x/R7800, ath79/generic, bcm27xx/bcm2711,
lantiq/Easybox 904 xDSL
Run-tested: ipq806x/R7800, lantiq/Easybox 904 xDSL
No dmesg regressions, everything functional
Signed-off-by: John Audia <graysky@archlinux.us>
[add lantiq test reports]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
John Crispin [Thu, 15 Oct 2020 11:36:10 +0000 (13:36 +0200)]
rtl838x: add DLink DGS-1210-16 support
Signed-off-by: John Crispin <john@phrozen.org>
Birger Koblitz [Thu, 15 Oct 2020 10:31:05 +0000 (12:31 +0200)]
rtl838x: Fix firmware handling
Fix wrong magic number verification for FW files.
Correct handling of external RTL8218B firmware PHY name in firmware.
Signed-off-by: Birger Koblitz <git@birger-koblitz.de>
Felix Fietkau [Thu, 15 Oct 2020 08:17:45 +0000 (10:17 +0200)]
build: always build package/kernel/linux
build: always build package/kernel/linux
If no in-tree module packages are selected, the build system does not process
package/kernel/linux. This package is required for building the virtual
'kernel' package, which is specified as a dependency for all kernel packages.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Andreas Oberritter [Fri, 2 Oct 2020 23:11:17 +0000 (01:11 +0200)]
rtl838x: do not default to the router DEVICE_TYPE
The router profile installs many packages unnecessary for
the operation of a typical ethernet switch. Instead of creating
an empty switch profile upfront, use the basic profile until
a set of common packages crystallizes.
Signed-off-by: Andreas Oberritter <obi@saftware.de>
Andreas Oberritter [Mon, 28 Sep 2020 23:26:14 +0000 (01:26 +0200)]
rtl838x: bundle phy firmware with Linux kernel
Fixes long delay on boot when booting from flash. The driver waits
for one minute for userspace to load firmware, before it becomes
available.
Signed-off-by: Andreas Oberritter <obi@saftware.de>
Birger Koblitz [Sat, 3 Oct 2020 09:20:48 +0000 (11:20 +0200)]
rtl838x: Add support for RTL839x internal PHY
This adds basic support for reading the internal PHYs of the RTL839x SoCs
and full support for the 2 PHYs connected to the 1000Base-X SerDes of
the RTL8393 SoC.
Signed-off-by: Birger Koblitz <git@birger-koblitz.de>
Birger Koblitz [Fri, 25 Sep 2020 04:49:51 +0000 (06:49 +0200)]
rtl838x: Add irq settings for RTL839x SoCs
This adds correct interrupt routing settings for IRQs on the RTL839x SoCs.
It also speeds up irq handling based on work by biot for all SoCs.
Signed-off-by: Birger Koblitz <git@birger-koblitz.de>
Rui Salvaterra [Sun, 11 Oct 2020 18:35:30 +0000 (19:35 +0100)]
treewide: enable the vDSO
The vDSO is used to accelerate some syscalls. It should work fine wherever it's
available, so enable it globally for all targets.
Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
Hans Dedecker [Mon, 12 Oct 2020 18:58:01 +0000 (20:58 +0200)]
glibc: update to latest 2.31 commit [BZ #26383]
32965a46ce intl: Handle translation output codesets with suffixes [BZ #26383]
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
Hal Martin [Sat, 9 May 2020 16:53:05 +0000 (16:53 +0000)]
sunxi: Correct manufacturer name to Sinovoip
Sinovoip is the manufacturer of the BPi-M2U:
http://www.banana-pi.org/m2u.html
Signed-off-by: Hal Martin <hal.martin@gmail.com>
Hal Martin [Sat, 9 May 2020 16:51:31 +0000 (16:51 +0000)]
sunxi: BPi-M2U kernel modules for onboard WiFi
Signed-off-by: Hal Martin <hal.martin@gmail.com>
Arturas Moskvinas [Tue, 11 Aug 2020 20:03:53 +0000 (23:03 +0300)]
sunxi: add support for FriendlyArm Zeropi
Specification
CPU: Allwinner H3, Quad-core Cortex-A7 Up to 1.2GHz
DDR3 RAM: 256MB/512MB
Connectivity: 10/100/1000Mbps Ethernet
USB Host: Type-A x 1
MicroSD Slot x 1
MicroUSB: for power input only
Debug Serial Port: 4Pin, 2.54 mm pitch pin header
Power Supply: DC 5V/2A
PCB Dimension: 40 x 40 x 1.2mm
Installation:
Burn the image file to an SD Card with dd or any image burning tool
Boot ZeroPi from the SD Card
The following features are working and tested:
Ethernet port 10/100/1000M Ethernet
Remarks: SBC is mostly compatible and boots with FriendlyARM NanoPI M1 plus DTS also (zeropi has no working hdmi)
Signed-off-by: Arturas Moskvinas <arturas.moskvinas@gmail.com>
Andre Heider [Tue, 8 Oct 2019 13:42:18 +0000 (15:42 +0200)]
sunxi: add a kmod package for sun4i_spdif
Tested on a A20 board:
$ cat /proc/asound/cards
0 [SPDIF ]: On-board_SPDIF - On-board SPDIF
On-board SPDIF
Size of the module for a 32bit kernel:
60708 linux-5.4.66/sound/soc/sunxi/sun4i-spdif.ko
Signed-off-by: Andre Heider <a.heider@gmail.com>
Andre Heider [Tue, 8 Oct 2019 19:07:43 +0000 (21:07 +0200)]
sunxi: add SND_SIMPLE_CARD to kernel config
This is required to expose an ALSA card for quite some boards:
$ git grep -l simple-audio-card \
arch/arm/boot/dts/sun?i* \
arch/arm64/boot/dts/allwinner/*
arch/arm/boot/dts/sun4i-a10-a1000.dts
arch/arm/boot/dts/sun5i-gr8-evb.dts
arch/arm/boot/dts/sun6i-a31-i7.dts
arch/arm/boot/dts/sun6i-a31s-sina31s.dts
arch/arm/boot/dts/sun7i-a20-cubietruck.dts
arch/arm/boot/dts/sun7i-a20-itead-ibox.dts
arch/arm/boot/dts/sun8i-a33-olinuxino.dts
arch/arm/boot/dts/sun8i-a33.dtsi
arch/arm/boot/dts/sun8i-a83t-cubietruck-plus.dts
arch/arm/boot/dts/sun8i-h3-beelink-x2.dts
arch/arm64/boot/dts/allwinner/sun50i-a64-bananapi-m64.dts
arch/arm64/boot/dts/allwinner/sun50i-a64-orangepi-win.dts
arch/arm64/boot/dts/allwinner/sun50i-a64-pine64.dts
arch/arm64/boot/dts/allwinner/sun50i-a64-pinebook.dts
arch/arm64/boot/dts/allwinner/sun50i-a64-pinephone.dtsi
arch/arm64/boot/dts/allwinner/sun50i-a64-pinetab.dts
arch/arm64/boot/dts/allwinner/sun50i-a64-sopine-baseboard.dts
arch/arm64/boot/dts/allwinner/sun50i-a64-teres-i.dts
arch/arm64/boot/dts/allwinner/sun50i-a64.dtsi
arch/arm64/boot/dts/allwinner/sun50i-h6-beelink-gs1.dts
The compressed 32bit kernel increases less than 1K:
Before:
3230768 zImage
After:
3231664 zImage
Signed-off-by: Andre Heider <a.heider@gmail.com>
Andre Heider [Tue, 8 Oct 2019 19:15:44 +0000 (21:15 +0200)]
kernel: add a kmod package for the SoC S/PDIF codec
Size of the modules for a Cortex A7 build:
43920 linux-5.4.66/sound/soc/codecs/snd-soc-spdif-rx.ko
44044 linux-5.4.66/sound/soc/codecs/snd-soc-spdif-tx.ko
Signed-off-by: Andre Heider <a.heider@gmail.com>
Andre Heider [Tue, 8 Oct 2019 18:06:57 +0000 (20:06 +0200)]
kernel: fix name of CONFIG_SND_SOC_GENERIC_DMAENGINE_PCM
CONFIG_SND_SOC_DMAENGINE_PCM was removed and replaced with
CONFIG_SND_SOC_GENERIC_DMAENGINE_PCM seven years ago, see:
https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/commit/?id=
28c4468b00a1e55e08cc20117de968f7c6275441
https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/commit/?id=
b7ae6f31d8243ec684af16bc5c763eccdfabaec0
Signed-off-by: Andre Heider <a.heider@gmail.com>
Andre Heider [Sat, 12 Sep 2020 08:28:21 +0000 (10:28 +0200)]
uboot-envtools: mvebu: fix config for mainline u-boot
Mainline u-boot dynamically passes the mtd partitions via devicetree:
$ cat /proc/mtd
dev: size erasesize name
mtd0:
003f0000 00001000 "firmware"
mtd1:
00010000 00001000 "u-boot-env"
Add support for this setup.
Signed-off-by: Andre Heider <a.heider@gmail.com>
Andre Heider [Sat, 12 Sep 2020 07:32:41 +0000 (09:32 +0200)]
mvebu: Add bootscript for espressobin to support mainline firmware
The generic bootscript is tailored around a downstream firmware and
doesn't work on a firmware built from mainline components.
Add a bootscript which:
* sets $console since mainline u-boot doesn't do that
* uses distro boot variables, so OpenWRT can be booted off any supported
device when using a mainline firmware
* sets missing distro boot variables for the downstream firmware
Booting with a downstream firmware is unchanged.
Booting with a mainline firmware now works.
Signed-off-by: Andre Heider <a.heider@gmail.com>
Hauke Mehrtens [Sat, 10 Oct 2020 10:10:53 +0000 (12:10 +0200)]
kernel: Move CONFIG_*_FS_XATTR to generic kernel config
This option is now activated in the generic kernel configuration, no
need to do it for a specific package.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Hauke Mehrtens [Sat, 10 Oct 2020 10:32:18 +0000 (12:32 +0200)]
kernel: move CONFIG_F2FS_CHECK_FS to generic kernel config
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Hauke Mehrtens [Sat, 10 Oct 2020 10:10:10 +0000 (12:10 +0200)]
kernel: Move CONFIG_F2FS_FS_SECURITY to generic kernel config
Move the CONFIG_F2FS_FS_SECURITY kernel configuration option to the
generic kernel configuration.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Hauke Mehrtens [Sat, 10 Oct 2020 10:02:02 +0000 (12:02 +0200)]
kernel: Remove 2FS_FS_XATTR and F2FS_STAT_FS symbols from target configs
This config option was moved to the generic kernel configuration.
Fixes: ab1bd576562b ("kernel: move F2FS_FS_XATTR and F2FS_STAT_FS symbols to generic")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Andre Heider [Tue, 6 Oct 2020 15:28:31 +0000 (17:28 +0200)]
arm-trusted-firmware-mvebu: fix topology for ESPRESSObin V3-V5 (1GB 1CS)
Signed-off-by: Andre Heider <a.heider@gmail.com>
Andre Heider [Wed, 23 Sep 2020 00:59:47 +0000 (02:59 +0200)]
uboot-mvebu: don't install 64bit binaries
u-boot binaries are not useful for these boards, they need to be combined
with atf for a proper firmware.
Signed-off-by: Andre Heider <a.heider@gmail.com>
Andre Heider [Sun, 20 Sep 2020 05:51:31 +0000 (07:51 +0200)]
uboot-mvebu: don't default to enable a3700 builds
u-boot binaries for this SoC are only required for the atf package,
disable them per default so they don't get build unnecessarily.
Signed-off-by: Andre Heider <a.heider@gmail.com>
Andre Heider [Sat, 26 Sep 2020 06:07:47 +0000 (08:07 +0200)]
uboot-mvebu: don't add CONFIG_NET_RANDOM_ETHADDR to defconfig
All targets already enable it in their defconfig with the used
u-boot version.
Signed-off-by: Andre Heider <a.heider@gmail.com>
Andre Heider [Sat, 26 Sep 2020 06:05:00 +0000 (08:05 +0200)]
uboot-mvebu: update to v2020.10
Remove merged patches and update the emmc set.
Signed-off-by: Andre Heider <a.heider@gmail.com>
Kabuli Chana [Tue, 1 Sep 2020 01:12:13 +0000 (19:12 -0600)]
mvebu: Correct regulatory country of WRT3200ACM
correct oversight on setting regulatory country and mac address of wireless configuration
change method of retrieving mac address
The MAC address for eth0 is rad out of the devinfo partition in some
other initial configuration script already.
Signed-off-by: Kabuli Chana <newtownBuild@gmail.com>
Kabuli Chana [Sun, 30 Aug 2020 02:11:25 +0000 (20:11 -0600)]
mvebu: add wrt3200acm to 03_wireless CC
correct device CC oversight
Set the initial wifi configuration like for the other similar Linksys
devices.
Signed-off-by: Kabuli Chana <newtownBuild@gmail.com>
Pali Rohár [Fri, 9 Oct 2020 09:49:14 +0000 (11:49 +0200)]
mvebu: armada-37xx: espressobin: Backport patch for ethernet switch aliases
Signed-off-by: Pali Rohár <pali@kernel.org>
Pali Rohár [Tue, 21 Jul 2020 12:11:08 +0000 (14:11 +0200)]
mvebu: armada-37xx: Backport PCI aardvark patches
This commit contains patches for PCI aardvark driver and relevant DTS
changes for Turris MOX and EspressoBin backported from mainline kernel.
It fixes support for old ATF, various wifi cards, mainly Compex WLE900VX.
Signed-off-by: Pali Rohár <pali@kernel.org>
Tony Ambardar [Fri, 25 Sep 2020 03:52:37 +0000 (20:52 -0700)]
scripts/qemustart: update malta to use MIPS64 R2 cpu
Explicitly set the QEMU cpu type and support the MIPS R2 ISA, for both
64-bit and 32-bit targets. The later previously supported MIPS R2 by
implicit default.
This is needed after commit
93608697f3 ("malta: update MIPS64 ISA to R2"),
otherwise booting malta images with scripts/qemustart will hang.
Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
Tony Ambardar [Fri, 14 Aug 2020 05:11:22 +0000 (22:11 -0700)]
malta: update MIPS64 ISA to R2
Usage of current R1 ISA is inconsistent with the MIPS32 subtarget, little
used and has limited utility for testing.
Many distros target a minimum R2 ISA. Debian MIPS 32-bit/64-bit ports all
use MIPS R2 ISA since Stretch, for example. Fedora's MIPS arch also targets
the R2 ISA for 32-bit/64-bit.
Widely used MIPS64 platforms like Octeon are based on the MIPS R2 ISA or
later, and benefit from having a compatible test platform in OpenWRT.
While Linux does support MIPS64 R1 targets, its usefulness for development
and testing is limited. As an example, the modern Linux eBPF JIT requires
a MIPS R2 ISA or later.
Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
[Refresh config and fix README]
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Josef Schlehofer [Fri, 2 Oct 2020 12:17:48 +0000 (14:17 +0200)]
trace-cmd: disable AUDIT (libaudit library)
If you compile first libaudit library and then trace-cmd package,
compilations fails with:
Package trace-cmd is missing dependencies for the following libraries:
libaudit.so.1
If you enable libaudit for trace-cmd, it will show system name calls while using command profile.
Try to be slim as much as possible - libaudit .ipk has 42,4 kB.
Signed-off-by: Josef Schlehofer <pepe.schlehofer@gmail.com>
Rosen Penev [Sat, 3 Oct 2020 00:36:16 +0000 (17:36 -0700)]
perf: disable libzstd support
libzstd from the packages feed gets picked up. Remove it.
Fixes:
Package perf is missing dependencies for the following libraries:
libzstd.so.1
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Marek Behún [Sat, 26 Sep 2020 21:49:50 +0000 (21:49 +0000)]
perf: pass CFLAGS correctly
For this package CFLAGS have to be passed via EXTRA_CFLAGS.
On arm this bug causes build to fail because no -fPIC is present in CFLAGS.
Signed-off-by: Marek Behún <kabel@blackhole.sk>
Marek Behún [Sat, 26 Sep 2020 21:42:52 +0000 (21:42 +0000)]
perf: fix building with musl when NLS is enabled
This package fails with a strange error when building with musl when NLS
is enabled. The configuration thinks that libelf is not present, even
though DEPENDS contains +libelf, because when NLS is enabled, libelf.so
depends on libintl, and the correct LDFLAGS are missing for
libintl-full. This then causes the configuration script to check for
glibc, but this fails because we are using musl.
Signed-off-by: Marek Behún <kabel@blackhole.sk>
Hans Dedecker [Sat, 10 Oct 2020 19:12:25 +0000 (21:12 +0200)]
netifd: update to latest git HEAD
64ff909 system-linux: initialize ifreq struct before using it
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
Adrian Schmutzler [Fri, 25 Sep 2020 22:46:13 +0000 (00:46 +0200)]
bcm63xx: move dts-v1 statement to top-level DTSI files
The "/dts-v1/;" identifier is supposed to be present once at the
top of a device tree file after the includes have been processed.
Like done for other targets recently, put the dts-v1 statement
into the top-level SoC-based DTSI files, and remove all other
occurences.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Adrian Schmutzler [Sun, 4 Oct 2020 13:12:57 +0000 (15:12 +0200)]
bcm63xx: add a few DTSI files to share definitions
After the LED labels have been made more general by removing
the model names, we can move several definitions to DTSI files
to reduce the amount of duplicate code.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Adrian Schmutzler [Sat, 10 Oct 2020 17:44:02 +0000 (19:44 +0200)]
bcm63xx: remove model name from LED labels
Like in the previous patches for various targets, this will remove
the "devicename" from LED labels in bcm63xx, as it's useless and
only creates complexity.
The devicename is removed in DTS files and 01_leds, merging
several cases on the way. A migration script is added for
existing configurations.
Note that a few labels were using "model::function" scheme without
color specified, those were converting to just "function" and the
necessary migrations were added to the migration script.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Daniel Golle [Fri, 9 Oct 2020 22:16:53 +0000 (23:16 +0100)]
kernel: move F2FS_FS_XATTR and F2FS_STAT_FS symbols to generic
Similar to how it was already done for other filesystems' *_FS_XATTR
kernel config symbols, also move CONFIG_F2FS_FS_XATTR=y and
CONFIG_F2FS_STAT_FS=y to target/linux/generic.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
John Audia [Wed, 7 Oct 2020 11:28:23 +0000 (07:28 -0400)]
kernel: bump 5.4 to 5.4.70
All modifications made by update_kernel.sh
Build system: x86_64
Build-tested: ipq806x/R7800, ath79/generic, bcm27xx/bcm2711
Run-tested: ipq806x/R7800
No dmesg regressions, everything functional
Signed-off-by: John Audia <graysky@archlinux.us>
Adrian Schmutzler [Fri, 9 Oct 2020 20:45:36 +0000 (22:45 +0200)]
ath79: drop redundant gpios on i2c
Since "sda-gpios" and "scl-gpios" are only available since kernel 4.19,
a few devices have redundantly defined "gpios" to also support older
kernels. Since we have nothing older than 4.19 now, we can remove
the redundant definitions.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Adrian Schmutzler [Fri, 9 Oct 2020 20:24:04 +0000 (22:24 +0200)]
ramips: drop kernel version switches
The ramips target only supports 5.4, so drop all kernel version
switches for older kernels there.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Daniel Golle [Fri, 9 Oct 2020 17:59:52 +0000 (18:59 +0100)]
seclic: depends on libsepol
Add missing dependency for target build of seclic which requires
libsepol (just like the host build requires libsepol/host).
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Adrian Schmutzler [Fri, 9 Oct 2020 14:44:30 +0000 (16:44 +0200)]
oxnas: fix qc_prep return in sata driver after kernel 5.4.69
This fixes a regression after a kernel change in 5.4.69 [1] that
led to build failure on oxnas/ox820:
drivers/ata/sata_oxnas.c:2238:13: error: initialization of
'enum ata_completion_errors (*)(struct ata_queued_cmd *)'
from incompatible pointer type
'void (*)(struct ata_queued_cmd *)' [-Werror=incompatible-pointer-types]
.qc_prep = sata_oxnas_qc_prep,
^~~~~~~~~~~~~~~~~~
drivers/ata/sata_oxnas.c:2238:13: note:
(near initialization for 'sata_oxnas_ops.qc_prep')
Our local driver is changed the same way as prototyped in the
kernel patch, i.e. return type is changed and AC_ERR_OK return
value is added.
[1] https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?id=
e11c83520cd04b813cd1748ee2a8f2c620e5f7e3
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Robert Marko [Wed, 7 Oct 2020 15:12:56 +0000 (17:12 +0200)]
ipq40xx: 5.4: move AR40xx driver into files
There is no point in keeping the AR40xx driver as a patch as its
not pending merge or backport.
To allow for easier maintenance until DSA is ready move it into
files like EDMA is.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
[combine with removal from patches-5.4]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Daniel Golle [Wed, 30 Sep 2020 21:03:20 +0000 (22:03 +0100)]
config: add option for dssp selinux policy
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Dominick Grift [Wed, 30 Sep 2020 10:21:19 +0000 (12:21 +0200)]
selinux-policy: adds new package
Signed-off-by: Dominick Grift <dominick.grift@defensec.nl>
Dominick Grift [Wed, 30 Sep 2020 10:17:19 +0000 (12:17 +0200)]
secilc: adds new package
Signed-off-by: Dominick Grift <dominick.grift@defensec.nl>
Daniel Golle [Sun, 5 Feb 2017 16:55:53 +0000 (17:55 +0100)]
rt2x00: mt7620: differentiate based on SoC's CHIP_VER
The vendor driver does things differently based on what it finds in the
SoC's CHIP_VER register, which should tell whether this is MT7620N or
MT7620A (PKG) and probably also the revision (VER) and most likely
also something about the silicon implementer (ECO).
Introduce codepaths just like the ones in the vendor driver to handle
the different chips properly.
Some of those paths are most likely dead code and left-overs from FPGA
versions or early prototypes of the chip. It'd thus be great if people
can post their kernel logs, at least the line telling the chip version
and eco, so we know what's actually out there in the wild -- all I
could find is
[ 0.000000] SoC Type: Ralink MT7620A ver:2 eco:6
and
[ 0.000000] SoC Type: Ralink MT7620N ver:2 eco:6
which would make things easier, as then we really just need to know
whether it's MT7620N or MT7620A and not care about FPGA or prototypes
with ver <= 1 and eco <= 2.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Paul Spooren [Mon, 5 Oct 2020 23:54:43 +0000 (13:54 -1000)]
kernel: clean up XATTR config symbols
Extended attributes are required for overlayfs and have hence been long
ago enabled for jffs2, but should be enabled unconditionally for all
other filesystems which may potentially serve as overlayfs' upper
directory. Previously it was inconsistently added in multiple targets.
Add symbols to generic kernel config and remove all *_XATTR symbols
from target configs.
Signed-off-by: Paul Spooren <mail@aparcar.org>
[keep things as they are for squashfs, improve commit message]
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Paul Spooren [Tue, 6 Oct 2020 19:17:02 +0000 (09:17 -1000)]
kernel: sort config-5.4 via kconfig.pl
The options were out of order which makes reviewing of changes harder.
Sort it before applying an actual change.
Signed-off-by: Paul Spooren <mail@aparcar.org>
Sven Roederer [Sun, 27 Sep 2020 21:07:38 +0000 (23:07 +0200)]
build, imagebuilder: Do not require compilers
The buildroot and SDK both require the compilers (gcc, g++) to be
installed on the host system, however the ImageBuilder uses precompiled
binaries.
This patch changes the prerequirements checks to skip the checking for
the compilers if running as ImageBuilder. A similar change has been
made for libncurses-dev in
4a1a58a3e2d2.
Signed-off-by: Sven Roederer <devel-sven@geroedel.de>
Acked-by: Paul Spooren <mail@aparcar.org>
Adrian Schmutzler [Wed, 30 Sep 2020 18:49:57 +0000 (20:49 +0200)]
lantiq: remove model name from LED labels
Like in the previous patches for other targets, this will remove
the "devicename" from LED labels in lantiq.
The devicename is removed in DTS files and 01_leds, consolidation
of definitions into DTSI files is done where (easily) possible,
and migration scripts are updated. The DTS/DTSI consolidation is
only performed for files-5.4.
For lantiq,easy98020 some LED definitions have the form
"devicename:function" without the color, so we need to implement
explicit migration for that one.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Adrian Schmutzler [Thu, 1 Oct 2020 18:40:03 +0000 (20:40 +0200)]
ipq40xx: use upstream DTS files for IPQ4019/AP-DK04.1
Upstream provides DTS(I) files for IPQ4019/AP-DK04.1, but we overwrite
them with local versions so far.
Remove the local files and use patches to be closer to upstream.
We already do the same for IPQ40xx/AP-DK01.1-C1.
Technically, this changes the compatible from "qcom,ipq4019" to
"qcom,ipq4019-dk04.1-c1", but it has never been implemented correctly
beforehand anyway.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Sungbo Eo [Fri, 18 Sep 2020 13:31:59 +0000 (22:31 +0900)]
ipq40xx: improve support for Edgecore ECW5211
This adds several stylistic and functional improvements of the recently
added Edgecore ECW5211, especially:
* Drop the local BDFs as those are already in the upstream under different names
* Add SPDX tag to DTS
* Add label MAC address
* Move LED trigger to DTS
* Remove unnecessary status="okay"
* Disable unused SS USB phy as the USB port only supports USB 2.0
* Make uboot-env partition writable
* Remove qcom,poll_required_dynamic property as the driver does not use it
* Tidy up the device recipe
Fixes: 4488b260a02e ("ipq40xx: add Edgecore ECW5211 support")
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
Acked-by: Robert Marko <robert.marko@sartura.hr>
Adrian Schmutzler [Thu, 1 Oct 2020 19:24:35 +0000 (21:24 +0200)]
ipq806x: remove model name from LED labels
Like in the previous patches for ath79 and ramips, this will remove
the "devicename" from LED labels in ipq806x.
The devicename is removed in DTS files and 01_leds, and a migration
script is added.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Adrian Schmutzler [Thu, 1 Oct 2020 19:15:47 +0000 (21:15 +0200)]
ipq40xx: remove model name from LED labels
Like in the previous patches for ath79 and ramips, this will remove
the "devicename" from LED labels in ipq40xx.
The devicename is removed in DTS files and 01_leds, and a migration
script is added. While at it, also harmonize capitalization of
wlan2G/wlan5G vs. wlan2g/wlan5g.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Roman Kuzmitskii [Tue, 6 Oct 2020 12:08:28 +0000 (12:08 +0000)]
ath79: rename ubnt,acb-isp to ubnt,aircube-isp
Use the full model name for this device to make it easier to
recognize for the users and in order to make it consistent with
the other devices.
While at it, fix sorting in 03_gpio_switches.
Signed-off-by: Roman Kuzmitskii <damex.pp@icloud.com>
[commit message facelift]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Hans Dedecker [Mon, 5 Oct 2020 19:16:15 +0000 (21:16 +0200)]
ppp: update to version 2.4.8.git-2020-10-03
2937722 Enable IPv6 by default (#171)
6d39c65 pppd: Fix blank password usage
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
Jo-Philipp Wich [Sun, 4 Oct 2020 21:04:51 +0000 (23:04 +0200)]
uhttpd: update to latest Git HEAD
14a3cb4 ubus: fix legacy empty reply format
0f38b03 client: fix spurious keepalive connection timeouts
88ba2fa client: really close connection on timeout
c186212 ubus: support GET method with CORS requests
Fixes: FS#3369
Fixes: https://github.com/openwrt/luci/issues/4467
Fixes: https://github.com/openwrt/luci/issues/4470
Fixes: https://github.com/openwrt/luci/issues/4479
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
DENG Qingfang [Mon, 28 Sep 2020 08:54:09 +0000 (16:54 +0800)]
toolchain/binutils: update to 2.35.1
Update binutils 2.35 to 2.35.1
Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
Adrian Schmutzler [Mon, 28 Sep 2020 12:31:02 +0000 (14:31 +0200)]
ath79: rename TP-Link TL-WPA8630P v2 (EU) to v2.0 (EU)
Since we have a v2.1 (EU) with different partitioning now, rename
the v2.0 to make the difference visible to the user more directly.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Joe Mullally [Sat, 12 Sep 2020 18:46:28 +0000 (19:46 +0100)]
ath79: add support for TP-Link TL-WPA8630P (EU) v2.1
This adds support for the TP-Link TL-WPA8630P (EU) in its v2.1
version. The only unique aspect for the firmware compared to v2
layout is the partition layout.
Note that while the EU version has different partitioning for
v2.0 and v2.1, the v2.1 (AU) is supported by the v2-int image.
If you plan to use this device, make sure you have a look at
the Wiki page to check whether the device is supported and
which image needs to be taken.
Specifications
--------------
- QCA9563 750MHz, 2.4GHz WiFi
- QCA9888 5GHz WiFi
- 8MiB SPI Flash
- 128MiB RAM
- 3 GBit Ports (QCA8337)
- PLC (QCA7550)
Installation
------------
Installation is possible from the OEM web interface. Make sure to
install the latest OEM firmware first, so that the PLC firmware is
at the latest version. However, please also check the Wiki page
for hints according to altered partitioning between OEM firmware
revisions.
Notes
-----
The OEM firmware has 0x620000 to 0x680000 unassigned, so we leave
this empty as well. It is complicated enough already ...
Signed-off-by: Joe Mullally <jwmullally@gmail.com>
[improve partitions, use v2 DTSI, add entry in 02_network, rewrite
and extend commit message]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Andre Heider [Fri, 4 Sep 2020 07:30:49 +0000 (09:30 +0200)]
omap: update uboot to v2020.04
Fixes the build error:
/usr/bin/ld: scripts/dtc/dtc-parser.tab.o:(.bss+0x10): multiple definition of `yylloc'; scripts/dtc/dtc-lexer.lex.o:(.bss+0x0): first defined here
collect2: error: ld returned 1 exit status
Successfully tested on boneblack.
Signed-off-by: Andre Heider <a.heider@gmail.com>
David Bauer [Wed, 26 Aug 2020 13:39:54 +0000 (15:39 +0200)]
ramips: fix logic level for DIR-645 buttons
The D-Link DIR-645 currently uses an incorrect logic level for its
buttons.
Correct them in order to prevent unintentional activation of failsafe
mode.
Reported-by: Perry Melange <isprotejesvalkata@gmail.com>
Signed-off-by: David Bauer <mail@david-bauer.net>
Marty Jones [Thu, 1 Oct 2020 07:04:48 +0000 (03:04 -0400)]
uboot-rockchip: add Rock Pi 4 support
Add support for the Raxda Rock Pi 4.
Signed-off-by: Marty Jones <mj8263788@gmail.com>
Marty Jones [Fri, 25 Sep 2020 18:00:40 +0000 (14:00 -0400)]
rockchip: add support for Radxa Rock Pi 4
This adds basic support for Radxa Rock Pi 4
Specification:
- RAM: 1 GB/ 2 GB/4 GB LPDDR4
- SoC: Rockchip RK3399
- CPU: 64bit hexa core processor
Dual Cortex-A72, freqency 1.8Ghz
with quad Cortex-A53, frequency 1.4Ghz
- USB: USB 3.0 OTG x1
hardware switch for host/device switch, upper one
USB 3.0 HOST x1
dedicated USB3.0 channel, lower one
USB 2.0 HOST x2
- Ethernet: 1x GbE
- Storage: eMMC module
uSD card
M.2 SSD
- Wireless: 802.11 ac wifi
Bluetooth 5.0
currently not supported
firmware Installation
======================
gzip -d xxx.img.gz, then dd the .img to SD/eMMC
======================
Device Tested: ROCK PI 4 Model B v1.3
Signed-off-by: Marty Jones <mj8263788@gmail.com>
David Bauer [Sun, 27 Sep 2020 08:05:18 +0000 (10:05 +0200)]
linux-firmware: update to
20200918
00a84c5 linux-firmware: Update AMD SEV firmware
71338c2 Merge branch 'for-master' of https://github.com/CosmicPenguin/linux-firmware into main
07367b9 linux-firmware: Update firmware file for Intel Bluetooth AX200
1d1586a linux-firmware: Update firmware file for Intel Bluetooth AX201
28b333d linux-firmware: Update firmware file for Intel Bluetooth 9560
db30380 linux-firmware: Update firmware file for Intel Bluetooth 9260
eb3aa1f Mellanox: Add new mlxsw_spectrum firmware xx.2008.1310
ec88f05 mediatek: update MT7915 firmware to
20200819
a9993f8 brcm: Fix a stale symlink for RPi3 model b+
f48fec4 qcom: Add updated a5xx and a6xx microcode
d5f9eea wl18xx: update firmware file 8.9.0.0.83
7a237c6 linux-firmware: mt7615: update firmware to
20200814 version
74bd44f amdgpu: add navi12 firmware from 20.30
b9f69cd amdgpu: update navi10 firmware for 20.30
Signed-off-by: David Bauer <mail@david-bauer.net>
David Bauer [Sat, 3 Oct 2020 11:50:49 +0000 (13:50 +0200)]
rockchip: enable Realtek PHY support
The NanoPi R2S features a Realtek Gigabit Ethernet PHY. Enable the
Realtek specific PHY driver to correctly configure internal delays.
Signed-off-by: David Bauer <mail@david-bauer.net>
David Bauer [Thu, 1 Oct 2020 08:25:45 +0000 (10:25 +0200)]
rockchip: fix NanoPi R2S PHY ID
Fix the PHY ID for the NanoPi R2S PHY compatible to match the used PHY.
The ID was wrong as I've accidentally picked the wrong upstream patch.
Signed-off-by: David Bauer <mail@david-bauer.net>
David Bauer [Sat, 3 Oct 2020 11:25:02 +0000 (13:25 +0200)]
Revert "uboot-rockchip: update NanoPi R2S patches"
This reverts commit
bda6f6572be630bcf9a1c8a429e40d8a53033af5.
This commit breaks the onboard ethernet on some units. Revert it for
now.
Signed-off-by: David Bauer <mail@david-bauer.net>
John Audia [Thu, 1 Oct 2020 13:22:00 +0000 (09:22 -0400)]
kernel: bump 5.4 to 5.4.69
Seemingly unneeded based on new upstream code so manually deleted:
layerscape:
820-usb-0007-usb-dwc3-gadget-increase-timeout-value-for-send-ep-c.patch
Manually merged:
generic-hack:
251-sound_kconfig.patch
All other modifications made by update_kernel.sh
Build system: x86_64
Build-tested: ipq806x/R7800, ath79/generic, bcm27xx/bcm2711
Run-tested: ipq806x/R7800, lantiq/Easybox 904 xDSL
No dmesg regressions, everything functional
Signed-off-by: John Audia <graysky@archlinux.us>
[add lantiq test report, minor commit message clarification]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
projects / openwrt / staging / hauke.git / log