Thibaut VARÈNE [Fri, 5 Jun 2020 12:06:02 +0000 (14:06 +0200)]
generic: platform/mikrotik: match RouterBOOT nomenclature
RouterBOOT cpu frequency settings are letter-indexed. Follow the
same logic for the sysfs interface.
Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
Thibaut VARÈNE [Fri, 5 Jun 2020 11:59:41 +0000 (13:59 +0200)]
generic: platform/mikrotik: fix routerboot_tag_show_u32s()
The routine would only accurately print out the first word.
Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
Fixes: 5ecf7d96 ("generic: routerboot sysfs platform driver")
Davide Fioravanti [Tue, 19 May 2020 23:27:56 +0000 (01:27 +0200)]
ramips: add support for Edimax Gemini RE23S
Hardware
--------
SoC: Mediatek MT7621AT (880 MHz, 2 cores 4 threads)
RAM: 128MB
FLASH: 16MB NOR (Macronix MX25L12805D)
ETH: 1x 10/100/1000 Mbps Ethernet (MT7530)
WIFI:
- 2.4GHz: 1x MT7615 (4x4:4)
- 5GHz: 1x MT7615 (4x4:4)
- 4 antennas: 2 external detachable and 2 internal
BTN:
- 1x Reset button
- 1x WPS button
LEDS:
- 1x Green led (Power)
- 1x Green-Amber-Red led (Wifi)
UART:
- 57600-8-N-1
Everything works correctly.
Installation
------------
Flash the factory image directly from OEM web interface.
(You can login using these credentials: admin/1234)
Restore OEM Firmware
--------------------
Flash the OEM "bin" firmware directly from LUCI.
The firmware is downloadable from the OEM web page.
Warning: Remember to not keep settings!
Warning2: Remember to force the flash.
Restoring procedure tested with RE23_1.08.bin
MAC addresses
-------------
factory 0x4 *:24
factory 0x8004 *:25
Cimage 0x07 *:24
Cimage 0x0D *:24
Cimage 0x13 *:24
Cimage 0x19 *:25
No other addresses were found in factory partition.
Since the label contains both the 2.4GHz and 5GHz mac address I decided
to set the 5GHz one as label-mac-device. Moreover it also corresponds
to the lan mac address.
Notes
-----
The wifi led in the OEM firmware changes colour depending on the signal
strength. This can be done in OpenWrt but just for one interface.
So for now will not be any default action for this led.
If you want to open the case, pay attention to the antenna placed on
the bottom part of the front cover.
The wire is a bit short and it breaks easily. (I broke it)
Signed-off-by: Davide Fioravanti <pantanastyle@gmail.com>
[fix two typos and add extended MAC address section to commit message]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Hauke Mehrtens [Tue, 7 Jul 2020 21:38:10 +0000 (23:38 +0200)]
ar71xx: Fix mikrotik NAND compile problem
This Fixes the folowing compile error:
drivers/mtd/nand/rb91x_nand.c: In function 'rb91x_nand_remove':
drivers/mtd/nand/rb91x_nand.c:445:16: error: 'rbni' undeclared (first use in this function)
nand_release(&rbni->chip);
Fixes: ce958dd88a7e ("kernel: Update kernel 4.14 to version 4.14.187")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Hans Dedecker [Tue, 7 Jul 2020 19:51:36 +0000 (21:51 +0200)]
curl: bump to 7.71.1
For changes in 7.71.1; see https://curl.haxx.se/changes.html#7_71_1
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
Hans Dedecker [Tue, 7 Jul 2020 19:39:36 +0000 (21:39 +0200)]
nat46: fix translation of ICMP protocol unreachable
Refresh patch
1182f30 nat46-core: Fix translation of ICMP protocol unreachable
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
Huangbin Zhan [Mon, 6 Jul 2020 23:14:42 +0000 (07:14 +0800)]
build: fix compatibility with python 3.6
On a system python3 is linked to python3.6, fail to perform json_overview_image_info
and got `TypeError: __init__() got an unexpected keyword argument 'capture_output'`.
This patch emulate the behaviour on python 3.7+.
Signed-off-by: Huangbin Zhan <zhanhb88@gmail.com>
Sergio E. Nemirowski [Mon, 15 Jun 2020 17:58:15 +0000 (20:58 +0300)]
build: mconf readme update
This updates mconf.c readme message to maintain less changes with
upstream and consistency with nconf.c
Signed-off-by: Sergio E. Nemirowski <sergio@outerface.net>
Sergio E. Nemirowski [Wed, 10 Jun 2020 01:33:21 +0000 (04:33 +0300)]
build: add nconfig
Add support for make target nconfig (ncurses)
Reviewed-by: Eneas U de Queiroz <cotequeiroz@gmail.com>
Signed-off-by: Sergio E. Nemirowski <sergio@outerface.net>
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Petr Štetiar [Wed, 20 May 2020 10:11:12 +0000 (12:11 +0200)]
ath79: nand: disable images for glinet_gl-ar750s
Fixes following build failures:
WARNING: Image file glinet_gl-ar750s-nor-kernel.bin is too big
WARNING: Image file glinet_gl-ar750s-nor-nand-kernel.bin is too big
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Andrey Bondar [Fri, 26 Jun 2020 08:16:00 +0000 (11:16 +0300)]
ath79: add support for 8devices Rambutan board
Rambutan is a Wifi module based on QCA9550/9557
http://www.8devices.com/products/rambutan
Specification:
- 720/600/200 MHz (CPU/DDR/AHB)
- 128 MB of DDR2 RAM
- 128 MB of NAND Flash
- 1x 100Mbps Ethernet
- 1x 1000Mbps Ethernet (PHY on dev-kit)
- 1x Wifi radio 2x2 MIMO, dualband 2.4 and 5 GHz
- 2x U.FL connectors on module, chip antennas on dev-kit
- 1x miniPCIe slot
- 2x USB2.0 host
- 2x UART
- SPI, I2C, GPIO
Flash instructions:
Upgrade from ar71xx target:
sysupgrade -F /tmp/openwrt-ath79-nand-8dev_rambutan-squashfs-sysupgrade.tar
or upgrade from GUI (don't save config)
Use factory image to flash from U-Boot:
tftpboot
80060000 openwrt-ath79-nand-8dev_rambutan-squashfs-factory.ubi
nand erase.part ubi
nand write
80060000 ubi ${filesize}
Signed-off-by: Petr Štetiar <ynezz@true.cz> [copy&pasted missing commit description]
Signed-off-by: Andrey Bondar <a.bondar@8devices.com>
Petr Štetiar [Wed, 1 Jul 2020 10:29:44 +0000 (12:29 +0200)]
dropbear: make rsa-sha2-256 pubkeys usable again
Upstream in commit
972d723484d8 ("split signkey_type and signature_type
for RSA sha1 vs sha256") has added strict checking of pubkey algorithms
which made keys with SHA-256 hashing algorithm unusable as they still
reuse the `ssh-rsa` public key format. So fix this by disabling the
check for `rsa-sha2-256` pubkeys.
Ref: https://tools.ietf.org/html/rfc8332#section-3
Fixes: d4c80f5b172e ("dropbear: bump to 2020.80")
Tested-by: Russell Senior <russell@personaltelco.net>
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Adrian Schmutzler [Tue, 7 Jul 2020 09:49:36 +0000 (11:49 +0200)]
ramips: use WiFi LED DT triggers for TP-Link RE650 v1
This moves WiFi LED triggers from 01_leds to device tree.
While at it, convert the labels there to lower case; this is
more commonly used and the change will actually remove competition
between DT trigger and leftover uci config on already installed
systems.
Suggested-by: Georgi Vlaev <georgi.vlaev@gmail.com>
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
David Bauer [Thu, 2 Apr 2020 19:53:59 +0000 (21:53 +0200)]
ath79: switch to kernel 5.4
As the reported major bugs are ironed out, switch to the new kernel to
begin testing with a broader audience.
Signed-off-by: David Bauer <mail@david-bauer.net>
Acked-by: Hauke Mehrtens <hauke@hauke-m.de>
David Bauer [Tue, 7 Jul 2020 08:32:09 +0000 (10:32 +0200)]
build: conditionally enable testing-kernel feature
Only enable the testing-kernel feature for the target when the testing
kernel version does not match the stable kernel version.
This way, the option for building the testing kernel in the build config
menu is only exposed when there's a testing kernel available.
Signed-off-by: David Bauer <mail@david-bauer.net>
Acked-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Aleksander Jan Bajkowski [Sun, 17 May 2020 10:33:56 +0000 (12:33 +0200)]
lantiq: set port numbers corresponding to reg value
Fix inconsistencies found in DTS files and sort ethernet ports based on
updated names.
Signed-off-by: Aleksander Jan Bajkowski <A.Bajkowski@stud.elka.pw.edu.pl>
[squash two separate patches, rephrase commit title/message]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Aleksander Jan Bajkowski [Sun, 17 May 2020 10:32:07 +0000 (12:32 +0200)]
lantiq: remove redundant includes from fritz736x DTS files
The removed lines are already included in vr9_avm_fritz736x.dtsi
Signed-off-by: Aleksander Jan Bajkowski <A.Bajkowski@stud.elka.pw.edu.pl>
[rephrase commit title/message]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Christoph Krapp [Mon, 6 Jul 2020 21:05:25 +0000 (23:05 +0200)]
ramips: add support for TP-Link RE500 v1
This device uses the same hardware as RE650 v1 which got supported in
8c51dde.
Hardware specification:
- SoC 880 MHz - MediaTek MT7621AT
- 128 MB of DDR3 RAM
- 16 MB - Winbond 25Q128FVSG
- 4T4R 2.4 GHz - MediaTek MT7615E
- 4T4R 5 GHz - MediaTek MT7615E
- 1x 1 Gbps Ethernet - MT7621AT integrated
- 7x LEDs (Power, 2G, 5G, WPS(x2), Lan(x2))
- 4x buttons (Reset, Power, WPS, LED)
- UART header (J1) - 2:GND, 3:RX, 4:TX
Serial console @ 57600,8n1
Flash instructions:
Upload
openwrt-ramips-mt7621-tplink_re500-v1-squashfs-factory.bin
from the RE500 web interface.
TFTP recovery to stock firmware:
Unfortunately, I can't find an easy way to recover the RE
without opening the device and using modified binaries. The
TFTP upload will only work if selected from u-boot, which
means you have to open the device and attach to the serial
console. The TFTP update procedure does *not* accept the
published vendor firmware binaries. However, it allows to
flash kernel + rootfs binaries, and this works if you have
a backup of the original contents of the flash. It's probably
possible to create special image out of the vendor binaries
and use that as recovery image.
Signed-off-by: Christoph Krapp <achterin@googlemail.com>
[remove dts-v1 in DTSI, do not touch WiFi LEDs for RE650, keep
state_default in DTS files, fix label-mac-device, use lower case
for WiFi LEDs]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Martin Blumenstingl [Mon, 6 Jul 2020 17:46:34 +0000 (19:46 +0200)]
lantiq: dts: Move the &usb_vbus nodes out of &gpio
Move the USB VBUS regulator nodes out of the GPIO controller node. This
fixes a problem where the "regulator-fixed" driver wasn't probed for
these regulators because the GPIO driver doesn't scan the child-nodes
and based on the dt-bindings documentation it's not supposed to.
This fixed the following error reported by Luca Olivetti:
...
dwc2
1e101000.usb: DWC OTG Controller
dwc2
1e101000.usb: new USB bus registered, assigned bus number 1
dwc2
1e101000.usb: irq 62, io mem 0x1e101000
dwc2
1e101000.usb: startup error -517
dwc2
1e101000.usb: USB bus 1 deregistered
dwc2
1e101000.usb: dwc2_hcd_init() FAILED, returning -517
Fixes: FS#1634
Cc: Luca Olivetti <luca@ventoso.org>
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
David Bauer [Mon, 6 Jul 2020 14:02:15 +0000 (16:02 +0200)]
ravpower-mcu: add missing PKG_RELEASE
This fixes the imagebuilder for this device.
Signed-off-by: David Bauer <mail@david-bauer.net>
Matthew Gyurgyik [Fri, 3 Jul 2020 21:08:25 +0000 (14:08 -0700)]
kernel/pcengines-apu2: detect apuv4 board
Upstream commit
3d00da1de3 ("platform/x86: pcengines-apuv2: detect apuv4
board")
On 5.4, this module fails on APUv4 due to non-matching DMI data. With this
patch, the module will match DMI data for the APUv4.
Signed-off-by: Matthew Gyurgyik <matthew@gyurgyik.io>
[include upstream patch description]
Signed-off-by: David Bauer <mail@david-bauer.net>
Lars Wessels [Sat, 4 Jul 2020 12:05:18 +0000 (14:05 +0200)]
lantiq: added switch-config for ARV752DPW
Add missing switch config (4 LAN-Ports + CPU).
Grey WAN port (used for ADSL) is not part of the switch.
Signed-off-by: Lars Wessels <software@bytebox.org>
[rework commit message]
Signed-off-by: David Bauer <mail@david-bauer.net>
Lars Wessels [Sat, 4 Jul 2020 11:59:17 +0000 (13:59 +0200)]
lantiq: wifi mac fix for ARV752DPW
Set wifi mac from flash partition 'board_config' to
match the label on the device (Easybox 802).
Currently the wifi mac is always set to 00:0c:43:28:60:00.
eth0 and WiFi will now share the same mac (as in original firmware).
Signed-off-by: Lars Wessels <software@bytebox.org>
[improve commit message]
Signed-off-by: David Bauer <mail@david-bauer.net>
Jan Hoffmann [Fri, 3 Jul 2020 11:53:47 +0000 (13:53 +0200)]
mac80211: allow ACS restriction with fixed channel
This can be useful when a DFS channel is configured, as the ACS channel
list is taken into account when switching channels after a radar event.
For example, this allows to prevent the SRD channels from being used in
that case.
Signed-off-by: Jan Hoffmann <jan@3e8.eu>
[reorder structure]
Signed-off-by: David Bauer <mail@david-bauer.net>
Sunguk Lee [Thu, 2 Jul 2020 09:32:43 +0000 (18:32 +0900)]
ramips: reduce spi-max-frequency for ipTIME A8004T
Reduce spi-max-frequency for ipTIME A8004T and disable
m25p,fast-read option.
A8004T uses `en25qh128` for the MTD.
This flash memory would allow 80MHz, sometimes kernel received
wrong id value in initramfs installed router.
(kernel expected `1c 70 18 1c 70 18`, but one of cases, it
was `9c 70 18 1c 70 18`)
In this case, openwrt can't detect the partition information,
it would write the inccorect data to the firmware partition and
also it would occur the bootlooping after sysupgrade.
Signed-off-by: Sunguk Lee <d3m3vilurr@gmail.com>
[minor commit title/message adjustments]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Adrian Schmutzler [Fri, 3 Jul 2020 13:46:31 +0000 (15:46 +0200)]
ipq806x: move serial0 to DTSI files
All device DTS files in the target set the serial0 property to the
same value (*). So, let's move the definitions to the DTSI files.
That's also where the kernel defines it (qcom-ipq8064-v1.0.dtsi).
* The only exception is ipq8064-db149, which defines
"serial0 = &uart2;", but inside a block called "alias" instead of
"aliases". It must be assumed that this is broken anyway, so we
don't touch it here.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Adrian Schmutzler [Fri, 3 Jul 2020 13:35:03 +0000 (15:35 +0200)]
ipq806x: move stdout-path to DTSI files
All device DTS files in the target set the stdout-path to the same
value. So, let's move the definitions to the DTSI files.
That's also where the kernel defines it (qcom-ipq8064-v1.0.dtsi).
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Adrian Schmutzler [Fri, 3 Jul 2020 13:00:58 +0000 (15:00 +0200)]
ipq806x: disentangle and clean up SoC DTSI files
So far, the DTSI files on ipq806x had a linear inheritance:
qcom-ipq8064.dtsi
v
qcom-ipq8064-v1.0.dtsi
v
qcom-ipq8064-v2.0.dtsi
v
qcom-ipq8065.dtsi
This poses problems when one wants to set something that is specific
to an architecture closer to the top of the tree.
In this patch, we remove the chain-like inheritance and have all
other files derived from qcom-ipq8064.dtsi (changing this name to
something more generic is not possible due to upstream use).
The removal of inheritance will require a few entries to be copied
from qcom-ipq8064-v2.0.dtsi to qcom-ipq8065.dtsi. However, it also
opens an opportunity for some clean-up:
- Many definitions can be improved by just using the innermost labels.
- Instead of disabling the CPU_SPC node for ipq8065, it is now off by
default and enabled where needed.
- Instead of patching phy-tx0-term-offset into qcom-ipq8064.dtsi and
then having it changed for qcom-ipq8064-v2.0/qcom-ipq8065, just have
the appropriate settings done in the lower DTSI files directly.
- For the opp_table0 adjustments for ipq8065, just redefine what's
changed, but don't add all the untouched properties again.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Sungbo Eo [Thu, 2 Jul 2020 16:38:09 +0000 (01:38 +0900)]
ipq806x: move common pinmux nodes to SoC DTSI
As almost same pinmux nodes are repeated in each device dts,
let's define them once in the ipq8064 dtsi and remove the rest.
* uart0_pins : Did not touch.
* i2c4_pins : This node seems to be not used at all in dts.
Added the most common form in the dtsi. Did not touch rpm_pins.
* spi_pins : The common mux node is already present in the dtsi.
Removed the duplicate nodes from dts.
* nand_pins : Moved the entire node.
* mdio0_pins : Moved the common mux node.
* rgmii2_pins: Moved the common mux node. "pins" property is overrided in ap161.
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
Hauke Mehrtens [Sun, 5 Jul 2020 17:27:23 +0000 (19:27 +0200)]
ar71xx: Fix mikrotik NAND compile problem
There is one closing bracket too much.
Fixes: ce958dd88a7e ("kernel: Update kernel 4.14 to version 4.14.187")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
John Audia [Mon, 29 Jun 2020 10:37:46 +0000 (06:37 -0400)]
linux-firmware: Update linux-firmware to
20200619
git log --pretty=oneline --abbrev-commit
20200122..
20200619
e96c121 (tag:
20200619, origin/main) amdgpu: update renoir firmware from 20.20 release
db0402e amdgpu: update picasso firmware from 20.20 release
c4e6e8f amdgpu: update raven2 firmware from 20.20 release
1967282 amdgpu: update raven firmware from 20.20 release
f73f82c amdgpu: add vega20 TA firmware from 20.20 release
9ecaba8 amdgpu: update vega20 firmware from 20.20 release
3866af1 amdgpu: update vega12 firmware from 20.20 release
adba945 amdgpu: update vega10 firmware from 20.20 release
3c5eef0 amdgpu: update navi10 firmware from 20.20 release
152c929 amdgpu: update navi14 firmware from 20.20 release
3890db3 (HEAD -> master, origin/master, origin/HEAD) rtl_nic: add firmware for RTL8125B
887d2a1 linux-firmware: Update firmware file for Intel Bluetooth AX200
3914943 linux-firmware: Update firmware file for Intel Bluetooth AX201
4966923 linux-firmware: Update firmware file for Intel Bluetooth 9560
5ee82c0 linux-firmware: Update firmware file for Intel Bluetooth 9260
d9880b1 Mellanox: Add new mlxsw_spectrum firmware xx.2007.1168
c2e313b rtw88: RTL8822C: update firmware version to v9.9
4d91664 Merge branch 'mrvl-prestera' of https://github.com/PLVision/linux-firmware
a54dfbe Merge branch 'for-upstream' of git://git.chelsio.net/pub/git/linux-firmware
51a773d cxgb4: Update firmware to revision 1.24.17.0
5611000 mrvl: add firmware for Prestera ASIC devices
8ba6fa6 (tag:
20200519) Merge tag 'iwlwifi-fw-2020-05-19' of git://git.kernel.org/pub/scm/linux/kernel/git/iwlwifi/linux-firmware
5ee1c7d iwlwifi: update and add new FWs from core50-70 and core52-81 releases
401bd6d rtw88: RTL8821C: add firmware file v24.5
2ae9974 iwlwifi: update FWs to core47-142 release
50c1340 iwlwifi: update 8265 FW
f8d32e4 rtw88: update firmware information and README
412f95a linux-firmware: add firmware for MT7915E
619d339 QCA: Add Bluetooth firmware for QCA9377
1392591 linux-firmware: add rebb firmware for mt7663
b2cad6a linux-firmware: Update firmware file for Intel Bluetooth AX200
c5ac1ad linux-firmware: Update firmware file for Intel Bluetooth AX201
642d115 linux-firmware: Update firmware file for Intel Bluetooth 9560
dc3047c linux-firmware: Update firmware file for Intel Bluetooth 9260
78c0348 (tag:
20200421) Use Link function for brcmfmac43362-sdio.lemaker,bananapro.txt
f2df706 Add symlink for Dell XPS 15 9550 Broadcom Bluetooth patch-ram file
87dcb0e rtl_bt: Update RTL8822C BT FW to 0x0999_3AA1
3aa3ae4 Merge branch 'for-upstream' of git://git.chelsio.net/pub/git/linux-firmware
8aa36f5 cxgb4: Update T6 config file
6314fa0 amdgpu: update vega20 firmware for 20.10
1f308f1 amdgpu: update vega12 firmware for 20.10
1ffd569 amdgpu: update vega10 firmware for 20.10
9a0b0f4 amdgpu: update renoir firmware for 20.10
428a747 amdgpu: update raven2 firmware for 20.10
624ecdf amdgpu: update raven firmware for 20.10
7532f50 amdgpu: update picasso firmware for 20.10
75e352e amdgpu: update navi10 firmware for 20.10
3c175d1 amdgpu: update navi14 firmware for 20.10
8d7ac32 amdgpu: add navi14 TA firmware from 20.10
dd6b4db Merge branch 'for-upstream' of git://git.chelsio.net/pub/git/linux-firmware
3afe520 cxgb4: Update firmware to revision 1.24.14.0
64dba0f Merge branch 'a630-zap' of https://github.com/andersson/linux-firmware
236ec45 linux-firmware: add firmware for MT7663 Wifi/BT combo device
107b9a2 Merge https://github.com/bgodavar/qca_bt_fw
5b240e5 Merge https://github.com/rjliao-qca/qca-btfw
47533bc linux-firmware: Update firmware file for Intel Bluetooth AX200
677930a linux-firmware: Update firmware file for Intel Bluetooth AX201
e6ff1e7 qcom: Add SDM845 Adreno ZAP shader firmware
1a8b0dc qca: Enable transparent WBS for WCN3991
4921f73 QCA: Add Bluetooth firmware for QCA6390
edf390c Merge branch 'v12573.77' of https://github.com/erinlo/linux_fw_scp
3c213aa mediatek: Add mt8183 SCP firmware
8eb0b28 (tag:
20200316) linux-firmware: Update firmware file for Intel Bluetooth AX200
b9f720f linux-firmware: Update firmware file for Intel Bluetooth AX201
426db50 linux-firmware: Update firmware file for Intel Bluetooth 9560
9361709 linux-firmware: Update firmware file for Intel Bluetooth 9260
3b3dd5a amdgpu: update vega20 firmware from 19.50
4871e7a amdgpu: update vega12 firmware from 19.50
4e7f0f8 amdgpu: update vega10 firmware from 19.50
fce60a9 rtl_bt: Add firmware and configuration files for RTL8822C BT UART chip
d553c05 Merge branch 'tgl_huc_7.0.12_dmc_2.06' of git://anongit.freedesktop.org/drm/drm-firmware
fb83402 i915: Add DMC firmware v2.06 for TGL
45d36b5 i915: add HuC firmware v7.0.12 for TGL
0148cfe Merge https://github.com/rjliao-qca/qca-btfw
94cb0a6 check_whence: python3/utf-8 support
7fa32bc Makefile: improve `make check` usefulness
4bb6805 mediatek: Remove in-tree symlinks
6f50efe Merge branch 'v1.1.4' of https://github.com/ruiwang-mtk/linux_fw_vpu
2db3978 qca: Fix blueooth firmware name for QCA6174
a8a18d1 mediatek: move MT8173 VPU FW to subfolder
efcfa03 linux-firmware: Update firmware file for Intel Bluetooth AX201
83cb43e Merge https://github.com/bgodavar/qca_bt_wcn3991
54b017d qca: Add firmware files for BT chip wcn3991.
2277987 nvidia: add TU116/117 signed firmware
f63922d drm/amdgpu: update to latest 19.50 firmware for raven
1168a90 Merge branch 'v1.1.4' of https://github.com/ruiwang-mtk/linux_fw_vpu_v1.1.4
0bd965d mediatek: update MT8173 VPU firmware to v1.1.4
6f89735 rtl_nic: update firmware for RTL8153A
5351afe rtl_bt: Update RTL8822C BT FW to V0x0998_C2B4
83a7c50 linux-firmware: add firmware for MT7622
feb91a4 linux-firmware: add version 2 for MT7615E
b791e15 amdgpu: update to latest navi10 firmware from 19.50
0ff2f37 Revert "radeon: update oland rlc microcode from amdgpu"
c2df39a Merge branch 'amlogic-vdec' of https://github.com/Elyotna/linux-firmware
fb505a6 amlogic: update video decoder firmwares
6d9f399 amdgpu: add renoir firmware for 19.50
2c08b38 amdgpu: update raven2 firmware for 19.50
8846543 Merge commit '
779514ec044a75ee6c9c20e52a2bf291f80d7d4e' of https://github.com/Netronome/linux-firmware
74d71b6 Merge branch 'bt-
20200122' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/linux-firmware
779514e nfp: update Agilio SmartNIC flower firmware to rev AOTC-2.12.A.13
3055060 qca: update bluetooth firmware for QCA6174
Signed-off-by: John Audia <graysky@archlinux.us>
Scott Roberts [Tue, 30 Jun 2020 19:55:16 +0000 (13:55 -0600)]
mvebu: config define i2c pxa slave
We are setting CONFIG_I2C_PXA is not set
If you do set pxa to y then you have issues if you do not have
CONFIG_I2C_PXA_SLAVE is not set
Fixes: dd13add3ceed ("kernel: i2c-pxa: remove slave")
Signed-off-by: Scott Roberts <ttocsr@gmail.com>
Daniel González Cabanelas [Sun, 28 Jun 2020 21:52:10 +0000 (23:52 +0200)]
mvebu: LS421DE: use automatic fan control with thermal zones
The Buffalo Linkstation LS421DE has a chassis fan for cooling two internal
hard drives. Currently there is no control over this fan, running always
at fixed medium speed.
With the recent jump to the kernel 5.4, now we can monitor the hard drive
temperature and control the fan with thermal zones.
Install the kmod-hwmon-drivetemp module and wire up a thermal zone on the
dts file to allow automatic fan control by the kernel.
Tested succesfully using a single Crucial BX500 SSD drive.
Signed-off-by: Daniel González Cabanelas <dgcbueu@gmail.com>
Hauke Mehrtens [Sat, 4 Jul 2020 13:16:27 +0000 (15:16 +0200)]
kernel: Update kernel 5.4 to version 5.4.50
Run tested: ath79, ipq40xx
Build tested: ath79, ipq40xx
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Hauke Mehrtens [Fri, 3 Jul 2020 23:34:26 +0000 (01:34 +0200)]
kernel: Update kernel 4.19 to version 4.19.131
Fixes:
- CVE-2020-10757
The "mtd: rawnand: Pass a nand_chip object to nand_release()" commit was
backported which needed some adaptations to other code.
Run tested: ath79
Build tested: ath79
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Hauke Mehrtens [Fri, 3 Jul 2020 22:54:41 +0000 (00:54 +0200)]
kernel: Update kernel 4.14 to version 4.14.187
Fixes:
- CVE-2020-10757
The "mtd: rawnand: Pass a nand_chip object to nand_release()" commit was
backported which needed some adaptations to other code.
Build tested: ramips
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
DENG Qingfang [Thu, 18 Jun 2020 06:20:15 +0000 (14:20 +0800)]
libjson-c: update to 0.14
Update libjson-c to 0.14
Changelog: https://github.com/json-c/json-c/wiki/Notes-for-v0.14-release
Switch to CMake because the upstream build system was changed
ipk size increased by 2KB
Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
Hauke Mehrtens [Thu, 2 Jul 2020 22:54:38 +0000 (00:54 +0200)]
kernel: Fix ath79 DSP exception at bootup
This resolves a hazard between a mtc0 and a mfc0 instruction after
activating the DSP support. Without this fix the CPU could use the old
value again and the DSP support would not be active.
Fixes: FS#2928, FS#2899
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Tested-by: Stefan Lippers-Hollmann <s.l-h@gmx.de> [ath79/tl-wdr3600; ath79/tl-wdr4300]
Tested-by: David Bauer <mail@david-bauer.net> [ocedo_koala/ocedo_raccoon]
Daniel Golle [Fri, 3 Jul 2020 20:57:52 +0000 (21:57 +0100)]
build,json: fix build failure in case no data is found
Only collect arch_packages if actually generating any output.
Fixes: commit f09b9319 ("build,json: store arch_packages in profiles.json"(
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Signed-off-by: Paul Spooren <mail@aparcar.org>
Antti Seppälä [Thu, 2 Jul 2020 07:53:02 +0000 (10:53 +0300)]
ath79: add support for GL.iNet GL-MiFi
Add support for the ar71xx supported GL.iNet GL-MiFi to ath79.
Specifications:
- Atheros AR9331
- 64 MB of RAM
- 16 MB of FLASH (SPI NOR)
- 2x 10/100/1000 Mbps Ethernet
- 2.4GHz (AR9330), 802.11b/g/n
- 1x USB 2.0 (vbus driven by GPIO)
- 4x LED, driven by GPIO
- 1x button (reset)
- 1x mini pci-e slot (vcc driven by GPIO)
Flash instructions:
Vendor software is based on openwrt so you can flash the sysupgrade
image via the vendor GUI or using command line sysupgrade utility.
Make sure to not save configuration over reflash as uci settings
differ between versions.
Note on MAC addresses:
Even though the platform is capable to providing separate MAC addresses
to the interfaces vendor firmware does not seem to take advantage of
that. It appears that there is only single unique pre-programmed
address in the art partition and vendor firmware uses that for
every interface (eth0/eth1/wlan0). Similar behaviour has also been
implemented in this patch.
Note on GPIOs:
In vendor firmware the gpio controlling mini pci-e slot is named
3gcontrol while it actually controls power supply to the entire mini
pci-e slot. Therefore a more descriptive name (minipcie) was chosen.
Also during development of this patch it became apparent that the
polarity of the signal is actually active low rather than active high
that can be found in vendor firmware.
Acknowledgements:
This patch is based on earlier work[1] done by Kyson Lok. Since the
initial mailing-list submission the patch has been modified to comply
with current openwrt naming schemes and dts conventions.
[1] http://lists.openwrt.org/pipermail/openwrt-devel/2018-September/019576.html
Signed-off-by: Antti Seppälä <a.seppala@gmail.com>
John Audia [Sun, 28 Jun 2020 10:24:46 +0000 (06:24 -0400)]
ipq806x: refresh config
Based on "make kernel_menuconfig CONFIG_TARGET=generic" and 5.4.49
CONFIG_LEDS_TRIGGER_DISK has been removed by the refresh and added
back manually in order to not revert
f93fcf8923aa ("ipq806x: enable
disk-activity LED trigger").
Signed-off-by: John Audia <graysky@archlinux.us>
[extend commit message]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Sungbo Eo [Fri, 3 Jul 2020 16:15:52 +0000 (01:15 +0900)]
kirkwood: support for button in Pogoplug V4
Pogoplug V4 has a reset button on a GPIO pin.
To use it, kmod-gpio-button-hotplug package needs to be installed.
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
Adrian Schmutzler [Fri, 3 Jul 2020 15:33:10 +0000 (17:33 +0200)]
ath79: drop redundant status for gpio target-wide
All definitions of gpio in SoC DTSI files do not set status, i.e.
have it enabled. This drops all remaining redundant "status = okay"
definitions in descendent files (mostly older ones).
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Adrian Schmutzler [Fri, 3 Jul 2020 15:21:12 +0000 (17:21 +0200)]
ath79: enable gpio on ar933x by default
All other SoC DTSI files have gpio enabled by default, only
ar9330/ar9331 disable it by default, only to have it enabled again
afterwards for each individual device.
So, do not disable it in the first place, and drop all device-specific
status statements afterwards.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Leon M. George [Fri, 26 Jul 2019 18:32:55 +0000 (20:32 +0200)]
ath79: add support for Compex WPJ344
Specifications:
SoC: AR9344
DRAM: 128MB DDR2
Flash: 16MB SPI-NOR
2 Gigabit ethernet ports
2×2 2.4GHz on-board radio
miniPCIe slot that supports 5GHz radio
PoE 48V IEEE 802.3af/at - 24V passive optional
USB 2.0 header
Installation:
To install, either start tftp in bin/targets/ath79/generic/ and use
the u-boot prompt over UART:
tftpboot 0x80500000 openwrt-ath79-generic-compex_wpj344-16m-squashfs-sysupgrade.bin
erase 0x9f030000 +$filesize
erase 0x9f680000 +1
cp.b $fileaddr 0x9f030000 $filesize
boot
The cpximg file can be used with sysupgrade in the stock firmware (add
SSH key in luci for root access) or with the built-in cpximg loader.
The cpximg loader can be started either by holding the reset button
during power up or by entering the u-boot prompt and entering 'cpximg'.
Once it's running, a TFTP-server under 192.168.1.1 will accept the image
appropriate for the board revision that is etched on the board.
For example, if the board is labelled '6A08':
tftp -v -m binary 192.168.1.1 -c put openwrt-ath79-generic-compex_wpj344-16m-squashfs-cpximg-6a08.bin
MAC addresses:
<&uboot 0x2e010> *:99 (label)
<&uboot 0x2e018> *:9a
<&uboot 0x2e020> *:9b
<&uboot 0x2e028> *:9c
Only the first two are used (for ethernet), the WiFi modules have
separate (valid) addresses. The latter two addresses are not used.
Signed-off-by: Leon M. George <leon@georgemail.eu>
[minor commit message adjustments, drop gpio in DTS, DTS style fixes,
sorting, drop unused cpximg recipe]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Paul Spooren [Wed, 1 Jul 2020 02:00:25 +0000 (16:00 -1000)]
build,json: store arch_packages in profiles.json
The `arch_packages` contains the supported package architecture.
Previously it was necessary to parse the `Packages` index for the line
`Architecture:`, requiring both an additional parser and file download.
Signed-off-by: Paul Spooren <mail@aparcar.org>
Hans Dedecker [Thu, 2 Jul 2020 20:24:39 +0000 (22:24 +0200)]
odhcpd: bump to latest git HEAD
5da5299 odhcpd: fix compilation with GCC10
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
Sungbo Eo [Thu, 2 Jul 2020 12:50:08 +0000 (21:50 +0900)]
ath79: rearrange nand node by register address
All other nodes in the DTS are placed in order of address space. Harmonize
the nand nodes as well.
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
Hans Dedecker [Tue, 30 Jun 2020 20:21:24 +0000 (22:21 +0200)]
curl: bump to 7.71.0
For changes in 7.71.0; see https://curl.haxx.se/changes.html#7_71_0
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
Álvaro Fernández Rojas [Wed, 1 Jul 2020 09:46:48 +0000 (11:46 +0200)]
ath10k-ct: update to version 2020-06-30
Backports commit "
a1769bb68a850508a492e3674ab1e5e479b11254", which reverts
upstream commit "
76d164f582150fd0259ec0fcbc485470bcd8033e" (ath10k: fix DMA
related firmware crashes on multiple devices).
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Paul Spooren [Tue, 30 Jun 2020 11:02:43 +0000 (01:02 -1000)]
build: store default/device packages in JSON
With this commit the `profiles.json` contain both the target specific
`default_packages` as well as the device specific `device_packages` as a
array of strings.
This information is required for downstream projects like the various
web-based interactive firmware generators.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Signed-off-by: Paul Spooren <mail@aparcar.org>
Hans Dedecker [Tue, 30 Jun 2020 20:02:20 +0000 (22:02 +0200)]
dropbear: bump to 2020.80
- drop patches (applied upstream)
* 001-backport_GNU_SOURCE-for-random.patch
* 002-backport-move-GNU_SOURCE-earlier.patch
* 010-backport-disable-toom-and-karatsuba.patch
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
Rui Salvaterra [Tue, 30 Jun 2020 16:23:12 +0000 (17:23 +0100)]
zram-swap: init: replace backticks with $()
This replaces deprecated backticks by more versatile $(...) syntax.
Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
[add commit description]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Rui Salvaterra [Tue, 30 Jun 2020 16:22:10 +0000 (17:22 +0100)]
dropbear: init: replace backticks with $()
This replaces deprecated backticks by more versatile $(...) syntax.
Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
[add commit description]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Rowan Border [Tue, 30 Jun 2020 13:35:56 +0000 (14:35 +0100)]
ramips: add support for TP-Link RE220 v2
TP-Link RE220 v2 is a wireless range extender with Ethernet and 2.4G and 5G
WiFi with internal antennas. It's based on MediaTek MT7628AN+MT7610EN.
This port of OpenWRT leverages work done by Andreas Böhler <dev@aboehler.at>
for the TP-Link RE200 v2 as both devices share the same SoC, flash layout
and GPIO pinout.
Specifications
MediaTek MT7628AN (580 Mhz)
64 MB of RAM
8 MB of FLASH
2T2R 2.4 GHz and 1T1R 5 GHz
1x 10/100 Mbps Ethernet
UART header on PCB (57600 8n1)
8x LED (GPIO-controlled), 2x button
There are 2.4G and 5G LEDs in red and green which are controlled separately.
Web Interface Installation
It is possible to upgrade to OpenWrt via the web interface. Simply flash
the -factory.bin from OEM. In contrast to a stock firmware, this will not
overwrite U-Boot.
Signed-off-by: Rowan Border <rowanjborder@gmail.com>
Kevin Darbyshire-Bryant [Sat, 18 Jan 2020 15:35:38 +0000 (15:35 +0000)]
kernel: cake: backport upstream tweaks & fixes
From upstream:
b8392808eb3f sch_cake: add RFC 8622 LE PHB support to CAKE diffserv handling
3f608f0c4136 sch_cake: fix a few style nits
8c95eca0bb8c sch_cake: don't call diffserv parsing code when it is not needed
9208d2863ac6 sch_cake: don't try to reallocate or unshare skb unconditionally
From netdev not yet accepted:
sch_cake: fix IP protocol handling in the presence of VLAN tags
The VLAN tag handling is actually wider than just cake so upstream are
working out how to fix it generically. We fix it here just for cake.
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
Kevin Darbyshire-Bryant [Mon, 29 Jun 2020 18:52:10 +0000 (19:52 +0100)]
kernel: cake: backport unused var patch to 5.4
This was backported to 4.19 and I clearly expected it to land in 5.4 but
it didn't (5.5) so backport it to 5.4 for consistency.
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
Kevin Darbyshire-Bryant [Thu, 25 Jun 2020 13:23:32 +0000 (14:23 +0100)]
kernel: cake: skb hash backport to 419
Commit
7b4877c2040a63332cd1f10023c51698fec2ed98 backported to 5.4 only,
backport to 4.19 as well.
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
Kevin Darbyshire-Bryant [Thu, 25 Jun 2020 12:39:54 +0000 (13:39 +0100)]
kernel: cake: renumber backport patches
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
David Bauer [Mon, 29 Jun 2020 13:51:37 +0000 (15:51 +0200)]
ramips: remove duplicate MAC assignment case
Cudy WR1000 and Wavlink WL-WN577A2 store WAN as well as label MAC address
at the same position in flash.
Suggested-by: Sungbo Eo <mans0n@gorani.run>
Signed-off-by: David Bauer <mail@david-bauer.net>
David Bauer [Mon, 29 Jun 2020 10:24:04 +0000 (12:24 +0200)]
package: add ravpower-mcu package
This package allows to read battery status information and control the
power state of the RAVPower RP-WD009 power management IC.
Signed-off-by: David Bauer <mail@david-bauer.net>
David Bauer [Mon, 29 Jun 2020 10:24:01 +0000 (12:24 +0200)]
ramips: add support for RAVPower RP-WD009
The RAVPower RP-WD009 is a batter-powered pocket sized router with SD
card lot and USB port.
Hardware
--------
CPU: MediaTek MT7628AN
RAM: 64M DDR2
FLASH: 16M GigaDevices SPI-NOR
WLAN: MediaTek MT7628AN 2T2R b/g/n
MediaTek MT7610E 1T1R n/ac
ETH: 1x FastEthernet
SD: SD Card slot
USB: USB 2.0
Custom PMIC on the I2C bus (address 0x0a).
Installation
------------
1. Press and hold down the reset button.
2. Power up the Device. Keep pressing the reset button for 10
more seconds until the Globe LED lights up.
3. Attach your Computer to the Ethernet port. Assign yourself the
address 10.10.10.1/24.
4. Access the recovery page at 10.10.10.128 and upload the OpenWrt
factory image.
5. The flashing will take around 1 minute. The device will reboot
automatically into OpenWrt.
Signed-off-by: David Bauer <mail@david-bauer.net>
David Bauer [Sun, 28 Jun 2020 23:07:00 +0000 (01:07 +0200)]
ath79: replace custom uImageArcher generation
The replaces the custom uImageArcher build step with the generic uImage
build step. The only different between these two is the difference in
the generated name.
Tested on: TP-Link Archer C59 v1
Acked-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Signed-off-by: David Bauer <mail@david-bauer.net>
Lars Wessels [Thu, 25 Jun 2020 19:09:59 +0000 (21:09 +0200)]
ramips: add support for WAVLINK WL-WN577A2
This commit adds support for the Wavlink WL-WN577A2 (black case) dual-band
wall-plug wireless router. In Germany this device is sold under the brand
name Maginon WL-755 (white case):
Device specifications:
- CPU: MediaTek MT7628AN (580MHz)
- Flash: 8MB
- RAM: 64MB
- Bootloader: U-Boot
- Ethernet: 2x 10/100 Mbps (Ralink RT3050)
- 2.4 GHz: 802.11b/g/n SoC
- 5 GHz: 802.11a/n/ac MT7610E
- Antennas: internal
- 4 green LEDs: 1 programmable (WPS) + LAN, WAN, POWER
- Buttons: Reset, WPS
- Small sliding power switch
Flashing instructions (U-boot):
- Configure a TFTP server on your PC/Laptop and set its IP
to 192.168.10.100
- Rename the OpenWrt image to firmware.bin and place it in the
root folder of the TFTP server
- Power off (using the small sliding power switch on the left
side) the device and connect an ethernet cable from its LAN
or WAN port to your PC/Laptop
- Press the WPS button (and keep it pressed)
- Power on the device (using the small power switch)
- After a few seconds, when the WAN/LAN LED stops blinking
very fast, release the WPS button
- Flashing OpenWrt takes less than a minute, system will
reboot automatically
- After reboot the WPS LED will indicate the current OpenWrt
running status
Signed-off-by: Lars Wessels <software@bytebox.org>
[removed unused labels - fix whitespace errors - wrap commit message]
Signed-off-by: David Bauer <mail@david-bauer.net>
Adrian Schmutzler [Wed, 24 Jun 2020 17:56:23 +0000 (19:56 +0200)]
mvebu: move definition of factory.img out of Device/Default
The Device/Default definition in mvebu defines an IMAGE/factory.img
which is not included in IMAGES, and only used twice in the
individual definitions. Move it out of the default definition
to keep it closer to the reassignment of IMAGES and make it more
consistent with respect to other values of IMAGE/factory.img
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Adrian Schmutzler [Wed, 24 Jun 2020 17:47:06 +0000 (19:47 +0200)]
ipq806x: set IMAGES in Device/Default definition
The Device/Default definition sets a default IMAGE/sysupgrade.bin,
but does not enable it by setting IMAGES. This is not consistent,
and has led to IMAGES being defined at various other places in the
file.
Thus, this patch consolidates the default value for IMAGES by putting
it in Device/Default. Since it's still overwritten where necessary,
this patch is cosmetic.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Adrian Schmutzler [Wed, 24 Jun 2020 17:40:45 +0000 (19:40 +0200)]
ipq40xx: set IMAGES in Device/Default definition
The Device/Default definition sets a default IMAGE/sysupgrade.bin,
but does not enable it by setting IMAGES. This is not consistent,
and has led to IMAGES being defined at various other places in the
file.
Thus, this patch consolidates the default value for IMAGES by putting
it in Device/Default. Since it's still overwritten where necessary,
this patch is cosmetic.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Sungbo Eo [Sat, 30 May 2020 16:33:03 +0000 (01:33 +0900)]
firmware-utils: sort tools alphabetically
Also remove leading whitespace after comma.
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
Adrian Schmutzler [Mon, 22 Jun 2020 11:41:27 +0000 (13:41 +0200)]
ath79: do not build TP-Link tiny images by default
For quite some time, the tiny (4M flash) TP-Link sysupgrade and
factory images cannot be built anymore by the buildbots, just
the initramfs-kernel.bin files are still there.
Disable these images for the buildbots and prevent useless builds.
Note that these devices still build fine with default settings,
even for kernel 5.4.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Adrian Schmutzler [Tue, 9 Jun 2020 17:46:22 +0000 (19:46 +0200)]
mvebu: remove non-existant board name solidrun,clearfog-a1
In 02_network, the board name solidrun,clearfog-a1 is used in a
case, but it does not seem to be used/exist anywhere else in OpenWrt.
The valid strings are:
- solidrun,clearfog-pro-a1
- solidrun,clearfog-base-a1
Fixes: 12795ec9f16b ("mvebu: split interface configuration for
clearfog pro and base")
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Leon M. George [Thu, 25 Jul 2019 09:59:56 +0000 (11:59 +0200)]
ath79: build Compex WPJ531 cpximg files
Generate additional images that are compatible to the cpximg loader.
The cpximg loader can be started either by holding the reset button during
power up or by entering the u-boot prompt and entering 'cpximg'.
Once it's running, a TFTP-server under 192.168.1.1 will accept the image
appropriate for the board revision that is etched on the board.
For example, if the board is labelled '7A04':
tftp -v -m binary 192.168.1.1 -c put openwrt-ath79-generic-compex_wpj531-16m-squashfs-cpximg-7A04.bin
These files can also be used with the sysupgrade utility in stock images (add
SSH key in luci for root access).
Signed-off-by: Leon M. George <leon@georgemail.eu>
[fix sorting of definitions]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Leon M. George [Thu, 25 Jul 2019 01:06:32 +0000 (03:06 +0200)]
ath79: add support for Compex WPJ531 (16M)
Specifications:
SoC: QCA9531
DRAM: 128MB DDR2
Flash: 16MB SPI-NOR
2 100MBit ethernet ports
2×2 2.4GHz on-board radio
miniPCIe slot that supports 5GHz radio
PoE 24V - 48V IEEE 802.3af optional
USB 2.0 header
Installation:
To install, start a tftp server in bin/targets/ath79/generic/ and use the
u-boot prompt over UART:
tftpboot 0x80500000 openwrt-ath79-generic-compex_wpj531-16m-squashfs-sysupgrade.bin
erase 0x9f030000 +$filesize
erase 0x9f680000 +1
cp.b $fileaddr 0x9f030000 $filesize
boot
The cpximg file can be used with sysupgrade in the stock firmware (add SSH key
in luci for root access).
Another way is to hold the reset button during power up or running 'cpximg' in
the u-boot prompt.
Once the last LED starts flashing regularly, a TFTP-server under 192.168.1.1
will accept the image appropriate for the board revision that is etched on the
board.
For example, if the board is labelled '7A04':
tftp -v -m binary 192.168.1.1 -c put openwrt-ath79-generic-compex_wpj531-16m-squashfs-cpximg-7A04.bin
MAC addresses:
<&uboot 0x2e010> *:cb (label)
<&uboot 0x2e018> *:cc
<&uboot 0x2e020> *:cd
<&uboot 0x2e028> *:ce
Only the first two are used (for ethernet), the WiFi modules have
separate (valid) addresses. The latter two addresses are not used.
Signed-off-by: Leon M. George <leon@georgemail.eu>
[commit title/message facelift, fix rssileds, add led aliases]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Hauke Mehrtens [Sat, 27 Jun 2020 16:38:12 +0000 (18:38 +0200)]
uboot-kirkwood: Revert "uboot-kirkwood: enable sata in nsa310 uboot"
This reverts commit
930f3c014821df423507c878415c7fb4910a454d.
The build fails with the following build error:
arm-openwrt-linux-muslgnueabi-ld.bfd: drivers/built-in.o: in function `ide_init':
build_dir/target-arm_xscale_musl_eabi/u-boot-nsa310/u-boot-2020.04/drivers/block/ide.c:750: undefined reference to `ide_preinit'
make[4]: *** [Makefile:1700: u-boot] Error 1
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Jan Hoffmann [Fri, 26 Jun 2020 21:46:19 +0000 (23:46 +0200)]
ramips: add support for NETGEAR WAC124
The WAC124 hardware appears to be identical to R6260/R6350/R6850.
SoC: MediaTek MT7621AT
RAM: 128M DDR3
FLASH: 128M NAND (Macronix MX30LF1G18AC)
WiFI: MediaTek MT7603 bgn 2T2R
MediaTek MT7615 nac 4T4R
ETH: SoC Integrated Gigabit Switch (1x WAN, 4x LAN)
USB: 1x USB 2.0
BTN: Reset, WPS
LED: Power, Internet, WiFi, USB (all green)
Installation:
The factory image can be flashed from the stock firmware web interface
or using nmrpflash. With nmrpflash it is also possible to revert to
stock firmware.
Signed-off-by: Jan Hoffmann <jan@3e8.eu>
Alex Lewontin [Fri, 21 Feb 2020 20:56:44 +0000 (15:56 -0500)]
ramips: add support for Netgear R6080
This adds support for the Netgear R6080, aka Netgear AC1000.
The R6080 has almost the same hardware as the Netgear R6120,
aka Netgear AC1200, but it lacks the USB port, has only 8 MiB flash and
uses a different SERCOMM_HWID.
Specification:
SoC: MediaTek MT7628 (580 MHz)
Flash: 8 MiB
RAM: 64 MiB
Wireless: 2.4Ghz (builtin) and 5Ghz (MT7612E)
LAN speed: 10/100
LAN ports: 4
WAN speed: 10/100
WAN ports: 1
UART (57600 8N1) on PCB
Installation:
Flashing OpenWRT from stock firmware requires nmrpflash. Use an ethernet
cable to connect to LAN port 1 of the R6080, and power the R6080 off.
From the connected workstation, run
`nmrpflash -i eth0 -f openwrt-ramips-mt76x8-netgear_r6080-squashfs-factory.img`,
replacing eth0 with the appropriate interface (can be identified by
running `nmrpflash -L`). Then power on the R6080. After flashing has finished,
power cycle the R6080, and it will boot into OpenWRT. Once OpenWRT has been
installed, subsequent flashes can use the web interface and sysupgrade files.
Signed-off-by: Alex Lewontin <alex.c.lewontin@gmail.com>
[rebase and adjust for 5.4]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Javier Marcet [Wed, 3 Jun 2020 12:01:37 +0000 (14:01 +0200)]
kernel: rename CONFIG_NETPRIO_CGROUP to CONFIG_CGROUP_NET_PRIO
This has been changed in kernel 3.14.
Signed-off-by: Javier Marcet <javier@marcet.info>
Hauke Mehrtens [Wed, 13 May 2020 21:42:15 +0000 (23:42 +0200)]
ath79: Fix ubnt_edgeswitch-8xp DEVICE_PACKAGES
switch-bcm53xx-mdio does not exists, use kmod-switch-bcm53xx-mdio
instead.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Cc: Tobias Schramm <tobleminer@gmail.com>
Daniel González Cabanelas [Sun, 26 Apr 2020 20:20:24 +0000 (22:20 +0200)]
mvebu: LS421DE: dts file improvements
- Delete useless HDD presence inputs: they aren't buttons, and probably
they are outputs in the stock firmware.
- Change the Function Button keycode: the current one isn't mapped by
the kernel module.
- Use the recommended property names for the ethernet stuff.
- Add missing i2c pinmux.
- Minor cosmetic changes.
Signed-off-by: Daniel González Cabanelas <dgcbueu@gmail.com>
Aleksander Jan Bajkowski [Sat, 2 May 2020 16:26:29 +0000 (18:26 +0200)]
lantiq: remove unused PHY drivers on xrx200
All boards on xrx200 use builtin switch and there is no supported device
with external switch.
It was copy paste from xway subtarget and was added in commit
18b76c66fbfea0e21ff66c6df432fa109c5bbb43.
Save 20.3 kB flash memory.
Signed-off-by: Aleksander Jan Bajkowski <A.Bajkowski@stud.elka.pw.edu.pl>
Qin Wei [Sat, 16 May 2020 07:51:36 +0000 (15:51 +0800)]
ramips: fix sd polling
This is fixed in 18.06, it appears again in 19.07.
Currently mt7628 sdcard driver do not support polling mode which is for
the device do not have card-detect pin to detect sd card insert. Without
this patch, device will not detect sdcard is inserted. This patch is a
fix of that.
Signed-off-by: Qin Wei <support@vocore.io>
Scott Roberts [Wed, 20 May 2020 19:28:39 +0000 (13:28 -0600)]
kernel: i2c-pxa: remove slave
Removing i2c pxa slave
The i2c-pxa is typically not use in slave mode. It does not make sense
to have slave mode enabled by default.
Having slave mode enabled prevents the i2c controller from being reset
if a real slave device such as an SFP is attached to the i2c-pxa bus and
locks it up.
Disable slave mode so that the i2c controller can be reset if the bus is
locked up.
If someone actually has a need for pxa slave mode this can be enabled in
kernel config.
Signed-off-by: Scott Roberts <ttocsr@gmail.com>
Sukru Senli [Fri, 22 May 2020 14:33:04 +0000 (16:33 +0200)]
netifd: replace timesvr with timesrv
/lib/netifd/dhcp.script:
Keep support for 'timesvr' while also supporting 'timesrv'
Add log message indicating deprecation of 'timesvr'
Signed-off-by: Sukru Senli <sukru.senli@iopsys.eu>
Alberto Bursi [Fri, 22 May 2020 16:49:15 +0000 (18:49 +0200)]
uboot-kirkwood: enable sata in nsa310 uboot
the uboot of nsa310 cannot use the network chip
as it is a realtek on the PCIe lanes and not a
Marvell ethernet from the SoC.
Therefore tftp is not possible on this device
and the only way to install is by loading files
from a USB drive.
If the USB subsystem is dead there is no way to
install OpenWrt.
Enable sata support and commands so it can be
used as a fallback in case of USB issues.
Signed-off-by: Alberto Bursi <bobafetthotmail@gmail.com>
Rogan Dawes [Wed, 27 May 2020 08:43:26 +0000 (10:43 +0200)]
sunxi: add text referencing Allwinner H3 and H5 CPUs
This makes it a little easier to figure out which options to choose.
Signed-off-by: Rogan Dawes <rogan@dawes.za.net>
Huangbin Zhan [Thu, 4 Jun 2020 13:49:54 +0000 (21:49 +0800)]
base-files: coreutil-sha256sum breaks status code
With package "coreutil-sha256sum" installed "sysupgrade" fails to perform 'sha256sum -s' and instead returns 'invalid option -- 's''.
This is caused due to:
different syntax for a sha256sum status check ('sha256sum --status' with "coreutil-sha256sum")
'/usr/bin/sha256sum' being symlinked to '/usr/bin/gnu-sha256sum' (after installation of "coreutil-sha256sum")
"coreutil-sha256sum" package from the packages feed replaces the Busybox sha256sum
This patch restores for 'sysupgrade' the busybox call to its sha256sum applet.
Signed-off-by: Huangbin Zhan <zhanhb88@gmail.com>
Gregory L. Dietsche [Sun, 7 Jun 2020 04:30:23 +0000 (23:30 -0500)]
x86: Support Intel 10 Gigabit Ethernet Cards
Support Intel 10 Gigabit Ethernet Cards in x86/64 images by default.
This ensures that systems with cards such as the Intel x520 will work properly.
Signed-off-by: Gregory L. Dietsche <Gregory.Dietsche@cuw.edu>
Huangbin Zhan [Wed, 3 Jun 2020 02:24:52 +0000 (10:24 +0800)]
ubox: add ALTERNATIVES
This avoids a conflict with the kmod util from the package feed.
Signed-off-by: Huangbin Zhan <zhanhb88@gmail.com>
Huangbin Zhan [Tue, 9 Jun 2020 23:11:08 +0000 (07:11 +0800)]
logger: enable alternatives support
Avoid conflict with busybox
Signed-off-by: Huangbin Zhan <zhanhb88@gmail.com>
Florian Eckert [Fri, 27 Mar 2020 15:23:14 +0000 (16:23 +0100)]
target/hack-5.4: platform/x86/pcengines: revert led simswich compromise
With this change the LED subsystem is abused in the kernel to switch the
simswap. This change will be reverted, so we could use again the gpio
subsystem.
Signed-off-by: Florian Eckert <fe@dev.tdt.de>
Florian Eckert [Tue, 2 Jul 2019 10:04:58 +0000 (12:04 +0200)]
kernel: add pcengines-apu2 module description
Add a module description for the new pcengnies-apu2 device driver.
This driver supports the front button and LEDs on the PC Engines
APUv2/APUv3 boards.
Signed-off-by: Florian Eckert <fe@dev.tdt.de>
Florian Eckert [Tue, 2 Jul 2019 10:04:27 +0000 (12:04 +0200)]
kernel: add gpio-amd-fch module description
Add a module description for the new gpio-amd-fch device driver.
Signed-off-by: Florian Eckert <fe@dev.tdt.de>
Florian Eckert [Mon, 30 Jul 2018 06:24:03 +0000 (08:24 +0200)]
kernel/leds-apu2: remove deprecated leds-apu2 driver
Remove leds-apu2 out of tree driver. There is a new upstream device gpio
and leds driver stack available for the APUv2 and APUv3 boards from pc
egnines. This new driver stack was add in kernel version 4.15.
Signed-off-by: Florian Eckert <fe@dev.tdt.de>
Adrian Schmutzler [Thu, 25 Jun 2020 21:09:05 +0000 (23:09 +0200)]
ath79: drop and consolidate redundant chosen/bootargs
In ath79, for several SoCs the console bootargs are defined to the
very same value in every device's DTS. Consolidate these definitions
in the SoC dtsi files and drop further redundant definitions elsewhere.
The only device without any bootargs set has been OpenMesh OM5P-AC V2.
This will now inherit the setting from qca955x.dtsi
Note that while this tidies up master a lot, it might develop into a
frequent pitfall for backports.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Adrian Schmutzler [Thu, 25 Jun 2020 20:31:40 +0000 (22:31 +0200)]
ramips: drop redundant chosen/bootargs
chosen/bootargs are defined to the same value in device DTS files
that is already set in the SoC DTSI. Remove the redundant definitions.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
David Bauer [Thu, 25 Jun 2020 00:36:19 +0000 (02:36 +0200)]
mac80211: ath9k: enable MFP capability unconditionally
ath9k will already fallback on software-crypto for chipsets not
supporting IEEE802.11w (MFP). So advertising MFP is not dependent
on disabling HW crypto for all traffic entirely.
Tested on Sonicwall SonicPoint Ni (AR9132)
Signed-off-by: David Bauer <mail@david-bauer.net>
Natalie Kagelmacher [Thu, 14 May 2020 08:44:21 +0000 (10:44 +0200)]
ath79: add support for AVM FRITZ!WLAN Repeater DVB-C
This commit adds support for the AVM FRITZ!WLAN Repeater DVB-C
SOC: Qualcomm Atheros QCA9556
RAM: 64 MiB
FLASH: 16 MB SPI-NOR
WLAN: QCA9556 3T3R 2.4 GHZ b/g/n and
QCA9880 3T3R 5 GHz n/ac
ETH: Atheros AR8033 1000 Base-T
DVB-C: EM28174 with MaxLinear MXL251 tuner
BTN: WPS Button
LED: Power, WLAN, TV, RSSI0-4
Tested and working:
- Ethernet (correct MAC, gigabit, iperf3 about 200 Mbit/s)
- 2.4 GHz Wi-Fi (correct MAC)
- 5 GHz Wi-Fi (correct MAC)
- WPS Button (tested using wifitoggle)
- LEDs
- Installation via EVA bootloader (FTP recovery)
- OpenWrt sysupgrade (both CLI and LuCI)
- Download of "urlader" (mtd0)
Not working:
- Internal USB
- DVB-C em28174+MxL251 (depends on internal USB)
Installation via EVA bootloader (FTP recovery):
Set NIC to 192.168.178.3/24 gateway 192.168.178.1 and power on the device,
connect to 192.168.178.1 through FTP and sign in with adam2/adam2:
ftp> quote USER adam2
ftp> quote PASS adam2
ftp> binary
ftp> debug
ftp> passive
ftp> quote MEDIA FLSH
ftp> put openwrt-sysupgrade.bin mtd1
Wait for "Transfer complete" together with the transfer details.
Wait two minutes to make sure flash is complete (just to be safe).
Then restart the device (power off and on) to boot into OpenWrt.
Revert your NIC settings to reach OpenWrt at 192.168.1.1
Signed-off-by: Natalie Kagelmacher <nataliek@pm.me>
[fixed sorting - removed change to other board -
prettified commit message]
Signed-off-by: David Bauer <mail@david-bauer.net>
Hans Dedecker [Wed, 24 Jun 2020 20:30:58 +0000 (22:30 +0200)]
dropbear: fix compilation for uClibc
Backport patches which fix compile issue for uClibc-ng :
dbrandom.c:174:8: warning: implicit declaration of function 'getrandom'; did you mean 'genrandom'? [-Wimplicit-function-declaration]
ret = getrandom(buf, sizeof(buf), GRND_NONBLOCK);
^~~~~~~~~
genrandom
dbrandom.c:174:36: error: 'GRND_NONBLOCK' undeclared (first use in this function); did you mean 'SOCK_NONBLOCK'?
ret = getrandom(buf, sizeof(buf), GRND_NONBLOCK);
^~~~~~~~~~~~~
SOCK_NONBLOCK
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
Sungbo Eo [Sun, 23 Feb 2020 12:39:26 +0000 (21:39 +0900)]
urandom-seed: update Makefile
- update SPDX license identifier
- use https in URL
- use default PKG_BUILD_DIR
Suggested-by: Josef Schlehofer <josef.schlehofer@nic.cz>
Tested-by: Josef Schlehofer <josef.schlehofer@nic.cz>
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
Sven Roederer [Mon, 11 May 2020 19:29:10 +0000 (21:29 +0200)]
feeds: add freifunk feed
Read the freifunk packages, that have been moved from the LuCI feed
into its own feed in January 2019.
Signed-off-by: Sven Roederer <freifunk@it-solutions.geroedel.de>
Jason A. Donenfeld [Tue, 23 Jun 2020 22:18:06 +0000 (16:18 -0600)]
wireguard: bump to 1.0.
20200623
* compat: drop centos 8.1 support as 8.2 is now out
Of note, as well, is that we now have both RHEL7 and RHEL8 in our CI at
<https://www.wireguard.com/build-status/>.
* Kbuild: remove -fvisibility=hidden from cflags
This fixes an issue when compiling wireguard as a module for ARM kernels in
THUMB2 mode without the JUMP11 workaround.
* noise: do not assign initiation time in if condition
Style fix.
* device: avoid circular netns references
Fixes a circular reference issue with network namespaces.
* netns: workaround bad 5.2.y backport
This works around a back backport in the 5.2.y series.
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
projects / openwrt / staging / chunkeey.git / log