git.openwrt.org Git - openwrt/staging/blogic.git/log

igb: Fix the transmission mode of queue 0 for Qav mode

When Qav mode is enabled, queue 0 should be kept on Stream Reservation
mode. From the i210 datasheet, section 8.12.19:

"Note: Queue0 QueueMode must be set to 1b when TransmitMode is set to
Qav." ("QueueMode 1b" represents the Stream Reservation mode)

The solution is to give queue 0 the all the credits it might need, so
it has priority over queue 1.

A situation where this can happen is when cbs is "installed" only on
queue 1, leaving queue 0 alone. For example:

$ tc qdisc replace dev enp2s0 handle 100: parent root mqprio num_tc 3 \
map 2 2 1 0 2 2 2 2 2 2 2 2 2 2 2 2 queues 1@0 1@1 2@2 hw 0

$ tc qdisc replace dev enp2s0 parent 100:2 cbs locredit -1470 \
hicredit 30 sendslope -980000 idleslope 20000 offload 1

Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

ixgbevf: ensure xdp_ring resources are free'd on error exit

The current error handling for failed resource setup for xdp_ring
data is a break out of the loop and returning 0 indicated everything
was OK, when in fact it is not. Fix this by exiting via the
error exit label err_setup_tx that will clean up the resources
correctly and return and error status.

Detected by CoverityScan, CID#1466879 ("Logically dead code")

Fixes: 21092e9ce8b1 ("ixgbevf: Add support for XDP_TX action")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

team: fix netconsole setup over team

The same fix in Commit dbe173079ab5 ("bridge: fix netconsole
setup over bridge") is also needed for team driver.

While at it, remove the unnecessary parameter *team from
team_port_enable_netpoll().

v1->v2:
- fix it in a better way, as does bridge.

Fixes: 0fb52a27a04a ("team: cleanup netpoll clode")
Reported-by: João Avelino Bellomo Filho <jbellomo@redhat.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge branch 'amd-xgbe-fixes'

aTom Lendacky says:

====================
amd-xgbe: AMD XGBE driver fixes 2018-04-23

This patch series addresses some issues in the AMD XGBE driver.

The following fixes are included in this driver update series:

- Improve KR auto-negotiation and training (2 patches)
  - Add pre and post auto-negotiation hooks
  - Use the pre and post auto-negotiation hooks to disable CDR tracking
    during auto-negotiation page exchange in KR mode
- Check for SFP tranceiver signal support and only use the signal if the
  SFP indicates that it is supported

This patch series is based on net.
====================

Signed-off-by: David S. Miller <davem@davemloft.net>

amd-xgbe: Only use the SFP supported transceiver signals

The SFP eeprom indicates the transceiver signals (Rx LOS, Tx Fault, etc.)
that it supports. Update the driver to include checking the eeprom data
when deciding whether to use a transceiver signal.

Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

amd-xgbe: Improve KR auto-negotiation and training

Update xgbe-phy-v2.c to make use of the auto-negotiation (AN) phy hooks
to improve the ability to successfully complete Clause 73 AN when running
at 10gbps.  Hardware can sometimes have issues with CDR lock when the
AN DME page exchange is being performed.

The AN and KR training hooks are used as follows:
- The pre AN hook is used to disable CDR tracking in the PHY so that the
  DME page exchange can be successfully and consistently completed.
- The post KR training hook is used to re-enable the CDR tracking so that
  KR training can successfully complete.
- The post AN hook is used to check for an unsuccessful AN which will
  increase a CDR tracking enablement delay (up to a maximum value).

Add two debugfs entries to allow control over use of the CDR tracking
workaround.  The debugfs entries allow the CDR tracking workaround to
be disabled and determine whether to re-enable CDR tracking before or
after link training has been initiated.

Also, with these changes the receiver reset cycle that is performed during
the link status check can be performed less often.

Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

amd-xgbe: Add pre/post auto-negotiation phy hooks

Add hooks to the driver auto-negotiation (AN) flow to allow the different
phy implementations to perform any steps necessary to improve AN.

Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

pppoe: check sockaddr length in pppoe_connect()

We must validate sockaddr_len, otherwise userspace can pass fewer data
than we expect and we end up accessing invalid data.

Fixes: 224cf5ad14c0 ("ppp: Move the PPP drivers")
Reported-by: syzbot+4f03bdf92fdf9ef5ddab@syzkaller.appspotmail.com
Signed-off-by: Guillaume Nault <g.nault@alphalink.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>

l2tp: check sockaddr length in pppol2tp_connect()

Check sockaddr_len before dereferencing sp->sa_protocol, to ensure that
it actually points to valid data.

Fixes: fd558d186df2 ("l2tp: Split pppol2tp patch into separate l2tp and ppp parts")
Reported-by: syzbot+a70ac890b23b1bf29f5c@syzkaller.appspotmail.com
Signed-off-by: Guillaume Nault <g.nault@alphalink.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: phy: marvell: clear wol event before setting it

If WOL event happened once, the LED[2] interrupt pin will not be
cleared unless we read the CSISR register. If interrupts are in use,
the normal interrupt handling will clear the WOL event. Let's clear the
WOL event before enabling it if !phy_interrupt_is_valid().

Signed-off-by: Jingju Hou <Jingju.Hou@synaptics.com>
Signed-off-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge git://git./pub/scm/linux/kernel/git/pablo/nf

Pablo Neira Ayuso says:

====================
Netfilter/IPVS fixes for net

The following patchset contains Netfilter/IPVS fixes for your net tree,
they are:

1) Fix SIP conntrack with phones sending session descriptions for different
   media types but same port numbers, from Florian Westphal.

2) Fix incorrect rtnl_lock mutex logic from IPVS sync thread, from Julian
   Anastasov.

3) Skip compat array allocation in ebtables if there is no entries, also
   from Florian.

4) Do not lose left/right bits when shifting marks from xt_connmark, from
   Jack Ma.

5) Silence false positive memleak in conntrack extensions, from Cong Wang.

6) Fix CONFIG_NF_REJECT_IPV6=m link problems, from Arnd Bergmann.

7) Cannot kfree rule that is already in list in nf_tables, switch order
   so this error handling is not required, from Florian Westphal.

8) Release set name in error path, from Florian.

9) include kmemleak.h in nf_conntrack_extend.c, from Stepheh Rothwell.

10) NAT chain and extensions depend on NF_TABLES.

11) Out of bound access when renaming chains, from Taehee Yoo.

12) Incorrect casting in xt_connmark leads to wrong bitshifting.
====================

Signed-off-by: David S. Miller <davem@davemloft.net>

ipv6: add RTA_TABLE and RTA_PREFSRC to rtm_ipv6_policy

KMSAN reported use of uninit-value that I tracked to lack
of proper size check on RTA_TABLE attribute.

I also believe RTA_PREFSRC lacks a similar check.

Fixes: 86872cb57925 ("[IPv6] route: FIB6 configuration using struct fib6_config")
Fixes: c3968a857a6b ("ipv6: RTA_PREFSRC support for ipv6 route source address selection")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: syzbot <syzkaller@googlegroups.com>
Acked-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

bonding: do not set slave_dev npinfo before slave_enable_netpoll in bond_enslave

After Commit 8a8efa22f51b ("bonding: sync netpoll code with bridge"), it
would set slave_dev npinfo in slave_enable_netpoll when enslaving a dev
if bond->dev->npinfo was set.

However now slave_dev npinfo is set with bond->dev->npinfo before calling
slave_enable_netpoll. With slave_dev npinfo set, __netpoll_setup called
in slave_enable_netpoll will not call slave dev's .ndo_netpoll_setup().
It causes that the lower dev of this slave dev can't set its npinfo.

One way to reproduce it:

  # modprobe bonding
  # brctl addbr br0
  # brctl addif br0 eth1
  # ifconfig bond0 192.168.122.1/24 up
  # ifenslave bond0 eth2
  # systemctl restart netconsole
  # ifenslave bond0 br0
  # ifconfig eth2 down
  # systemctl restart netconsole

The netpoll won't really work.

This patch is to remove that slave_dev npinfo setting in bond_enslave().

Fixes: 8a8efa22f51b ("bonding: sync netpoll code with bridge")
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

tcp: don't read out-of-bounds opsize

The old code reads the "opsize" variable from out-of-bounds memory (first
byte behind the segment) if a broken TCP segment ends directly after an
opcode that is neither EOL nor NOP.

The result of the read isn't used for anything, so the worst thing that
could theoretically happen is a pagefault; and since the physmap is usually
mostly contiguous, even that seems pretty unlikely.

The following C reproducer triggers the uninitialized read - however, you
can't actually see anything happen unless you put something like a
pr_warn() in tcp_parse_md5sig_option() to print the opsize.

====================================
#define _GNU_SOURCE
#include <arpa/inet.h>
#include <stdlib.h>
#include <errno.h>
#include <stdarg.h>
#include <net/if.h>
#include <linux/if.h>
#include <linux/ip.h>
#include <linux/tcp.h>
#include <linux/in.h>
#include <linux/if_tun.h>
#include <err.h>
#include <sys/types.h>
#include <sys/stat.h>
#include <fcntl.h>
#include <string.h>
#include <stdio.h>
#include <unistd.h>
#include <sys/ioctl.h>
#include <assert.h>

void systemf(const char *command, ...) {
  char *full_command;
  va_list ap;
  va_start(ap, command);
  if (vasprintf(&full_command, command, ap) == -1)
    err(1, "vasprintf");
  va_end(ap);
  printf("systemf: <<<%s>>>\n", full_command);
  system(full_command);
}

char *devname;

int tun_alloc(char *name) {
  int fd = open("/dev/net/tun", O_RDWR);
  if (fd == -1)
    err(1, "open tun dev");
  static struct ifreq req = { .ifr_flags = IFF_TUN|IFF_NO_PI };
  strcpy(req.ifr_name, name);
  if (ioctl(fd, TUNSETIFF, &req))
    err(1, "TUNSETIFF");
  devname = req.ifr_name;
  printf("device name: %s\n", devname);
  return fd;
}

#define IPADDR(a,b,c,d) (((a)<<0)+((b)<<8)+((c)<<16)+((d)<<24))

void sum_accumulate(unsigned int *sum, void *data, int len) {
  assert((len&2)==0);
  for (int i=0; i<len/2; i++) {
    *sum += ntohs(((unsigned short *)data)[i]);
  }
}

unsigned short sum_final(unsigned int sum) {
  sum = (sum >> 16) + (sum & 0xffff);
  sum = (sum >> 16) + (sum & 0xffff);
  return htons(~sum);
}

void fix_ip_sum(struct iphdr *ip) {
  unsigned int sum = 0;
  sum_accumulate(&sum, ip, sizeof(*ip));
  ip->check = sum_final(sum);
}

void fix_tcp_sum(struct iphdr *ip, struct tcphdr *tcp) {
  unsigned int sum = 0;
  struct {
    unsigned int saddr;
    unsigned int daddr;
    unsigned char pad;
    unsigned char proto_num;
    unsigned short tcp_len;
  } fakehdr = {
    .saddr = ip->saddr,
    .daddr = ip->daddr,
    .proto_num = ip->protocol,
    .tcp_len = htons(ntohs(ip->tot_len) - ip->ihl*4)
  };
  sum_accumulate(&sum, &fakehdr, sizeof(fakehdr));
  sum_accumulate(&sum, tcp, tcp->doff*4);
  tcp->check = sum_final(sum);
}

int main(void) {
  int tun_fd = tun_alloc("inject_dev%d");
  systemf("ip link set %s up", devname);
  systemf("ip addr add 192.168.42.1/24 dev %s", devname);

  struct {
    struct iphdr ip;
    struct tcphdr tcp;
    unsigned char tcp_opts[20];
  } __attribute__((packed)) syn_packet = {
    .ip = {
      .ihl = sizeof(struct iphdr)/4,
      .version = 4,
      .tot_len = htons(sizeof(syn_packet)),
      .ttl = 30,
      .protocol = IPPROTO_TCP,
      /* FIXUP check */
      .saddr = IPADDR(192,168,42,2),
      .daddr = IPADDR(192,168,42,1)
    },
    .tcp = {
      .source = htons(1),
      .dest = htons(1337),
      .seq = 0x12345678,
      .doff = (sizeof(syn_packet.tcp)+sizeof(syn_packet.tcp_opts))/4,
      .syn = 1,
      .window = htons(64),
      .check = 0 /*FIXUP*/
    },
    .tcp_opts = {
      /* INVALID: trailing MD5SIG opcode after NOPs */
      1, 1, 1, 1, 1,
      1, 1, 1, 1, 1,
      1, 1, 1, 1, 1,
      1, 1, 1, 1, 19
    }
  };
  fix_ip_sum(&syn_packet.ip);
  fix_tcp_sum(&syn_packet.ip, &syn_packet.tcp);
  while (1) {
    int write_res = write(tun_fd, &syn_packet, sizeof(syn_packet));
    if (write_res != sizeof(syn_packet))
      err(1, "packet write failed");
  }
}
====================================

Fixes: cfb6eeb4c860 ("[TCP]: MD5 Signature Option (RFC2385) support.")
Signed-off-by: Jann Horn <jannh@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge git://git./pub/scm/linux/kernel/git/bpf/bpf

Daniel Borkmann says:

====================
pull-request: bpf 2018-04-21

The following pull-request contains BPF updates for your *net* tree.

The main changes are:

1) Fix a deadlock between mm->mmap_sem and bpf_event_mutex when
   one task is detaching a BPF prog via perf_event_detach_bpf_prog()
   and another one dumping through bpf_prog_array_copy_info(). For
   the latter we move the copy_to_user() out of the bpf_event_mutex
   lock to fix it, from Yonghong.

2) Fix test_sock and test_sock_addr.sh failures. The former was
   hitting rlimit issues and the latter required ping to specify
   the address family, from Yonghong.

3) Remove a dead check in sockmap's sock_map_alloc(), from Jann.

4) Add generated files to BPF kselftests gitignore that were previously
   missed, from Anders.
====================

Signed-off-by: David S. Miller <davem@davemloft.net>

ibmvnic: Clean actual number of RX or TX pools

Avoid using value stored in the login response buffer when
cleaning TX and RX buffer pools since these could be inconsistent
depending on the device state. Instead use the field in the driver's
private data that tracks the number of active pools.

Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge branch 'net-sched-ife-malformed-ife-packet-fixes'

Alexander Aring says:

====================
net: sched: ife: malformed ife packet fixes

As promised at netdev 2.2 tc workshop I am working on adding scapy support for
tdc testing. It is still work in progress. I will submit the patches to tdc
later (they are not in good shape yet). The good news is I have been able to
find bugs which normal packet testing would not be able to find.
With fuzzy testing I was able to craft certain malformed packets that IFE
action was not able to deal with. This patch set fixes those bugs.

changes since v4:
- use pskb_may_pull before pointer assign

changes since v3:
- use pskb_may_pull

changes since v2:
- remove inline from __ife_tlv_meta_valid
- add const to cast to meta_tlvhdr
- add acked and reviewed tags
====================

Signed-off-by: David S. Miller <davem@davemloft.net>

net: sched: ife: check on metadata length

This patch checks if sk buffer is available to dererence ife header. If
not then NULL will returned to signal an malformed ife packet. This
avoids to crashing the kernel from outside.

Signed-off-by: Alexander Aring <aring@mojatatu.com>
Reviewed-by: Yotam Gigi <yotam.gi@gmail.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: sched: ife: handle malformed tlv length

There is currently no handling to check on a invalid tlv length. This
patch adds such handling to avoid killing the kernel with a malformed
ife packet.

Signed-off-by: Alexander Aring <aring@mojatatu.com>
Reviewed-by: Yotam Gigi <yotam.gi@gmail.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: sched: ife: signal not finding metaid

We need to record stats for received metadata that we dont know how
to process. Have find_decode_metaid() return -ENOENT to capture this.

Signed-off-by: Alexander Aring <aring@mojatatu.com>
Reviewed-by: Yotam Gigi <yotam.gi@gmail.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

strparser: Do not call mod_delayed_work with a timeout of LONG_MAX

struct sock's sk_rcvtimeo is initialized to
LONG_MAX/MAX_SCHEDULE_TIMEOUT in sock_init_data. Calling
mod_delayed_work with a timeout of LONG_MAX causes spurious execution of
the work function. timer->expires is set equal to jiffies + LONG_MAX.
When timer_base->clk falls behind the current value of jiffies,
the delta between timer_base->clk and jiffies + LONG_MAX causes the
expiration to be in the past. Returning early from strp_start_timer if
timeo == LONG_MAX solves this problem.

Found while testing net/tls_sw recv path.

Fixes: 43a0c6751a322847 ("strparser: Stream parser for messages")
Reviewed-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Doron Roberts-Kedes <doronrk@fb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

ipv6: sr: fix NULL pointer dereference in seg6_do_srh_encap()- v4 pkts

In case of seg6 in encap mode, seg6_do_srh_encap() calls set_tun_src()
in order to set the src addr of outer IPv6 header.

The net_device is required for set_tun_src(). However calling ip6_dst_idev()
on dst_entry in case of IPv4 traffic results on the following bug.

Using just dst->dev should fix this BUG.

[  196.242461] BUG: unable to handle kernel NULL pointer dereference at 0000000000000000
[  196.242975] PGD 800000010f076067 P4D 800000010f076067 PUD 10f060067 PMD 0
[  196.243329] Oops: 0000 [#1] SMP PTI
[  196.243468] Modules linked in: nfsd auth_rpcgss nfs_acl nfs lockd grace fscache sunrpc crct10dif_pclmul crc32_pclmul ghash_clmulni_intel pcbc aesni_intel aes_x86_64 crypto_simd cryptd input_leds glue_helper led_class pcspkr serio_raw mac_hid video autofs4 hid_generic usbhid hid e1000 i2c_piix4 ahci pata_acpi libahci
[  196.244362] CPU: 2 PID: 1089 Comm: ping Not tainted 4.16.0+ #1
[  196.244606] Hardware name: innotek GmbH VirtualBox/VirtualBox, BIOS VirtualBox 12/01/2006
[  196.244968] RIP: 0010:seg6_do_srh_encap+0x1ac/0x300
[  196.245236] RSP: 0018:ffffb2ce00b23a60 EFLAGS: 00010202
[  196.245464] RAX: 0000000000000000 RBX: ffff8c7f53eea300 RCX: 0000000000000000
[  196.245742] RDX: 0000f10000000000 RSI: ffff8c7f52085a6c RDI: ffff8c7f41166850
[  196.246018] RBP: ffffb2ce00b23aa8 R08: 00000000000261e0 R09: ffff8c7f41166800
[  196.246294] R10: ffffdce5040ac780 R11: ffff8c7f41166828 R12: ffff8c7f41166808
[  196.246570] R13: ffff8c7f52085a44 R14: ffffffffb73211c0 R15: ffff8c7e69e44200
[  196.246846] FS:  00007fc448789700(0000) GS:ffff8c7f59d00000(0000) knlGS:0000000000000000
[  196.247286] CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[  196.247526] CR2: 0000000000000000 CR3: 000000010f05a000 CR4: 00000000000406e0
[  196.247804] Call Trace:
[  196.247972]  seg6_do_srh+0x15b/0x1c0
[  196.248156]  seg6_output+0x3c/0x220
[  196.248341]  ? prandom_u32+0x14/0x20
[  196.248526]  ? ip_idents_reserve+0x6c/0x80
[  196.248723]  ? __ip_select_ident+0x90/0x100
[  196.248923]  ? ip_append_data.part.50+0x6c/0xd0
[  196.249133]  lwtunnel_output+0x44/0x70
[  196.249328]  ip_send_skb+0x15/0x40
[  196.249515]  raw_sendmsg+0x8c3/0xac0
[  196.249701]  ? _copy_from_user+0x2e/0x60
[  196.249897]  ? rw_copy_check_uvector+0x53/0x110
[  196.250106]  ? _copy_from_user+0x2e/0x60
[  196.250299]  ? copy_msghdr_from_user+0xce/0x140
[  196.250508]  sock_sendmsg+0x36/0x40
[  196.250690]  ___sys_sendmsg+0x292/0x2a0
[  196.250881]  ? _cond_resched+0x15/0x30
[  196.251074]  ? copy_termios+0x1e/0x70
[  196.251261]  ? _copy_to_user+0x22/0x30
[  196.251575]  ? tty_mode_ioctl+0x1c3/0x4e0
[  196.251782]  ? _cond_resched+0x15/0x30
[  196.251972]  ? mutex_lock+0xe/0x30
[  196.252152]  ? vvar_fault+0xd2/0x110
[  196.252337]  ? __do_fault+0x1f/0xc0
[  196.252521]  ? __handle_mm_fault+0xc1f/0x12d0
[  196.252727]  ? __sys_sendmsg+0x63/0xa0
[  196.252919]  __sys_sendmsg+0x63/0xa0
[  196.253107]  do_syscall_64+0x72/0x200
[  196.253305]  entry_SYSCALL_64_after_hwframe+0x3d/0xa2
[  196.253530] RIP: 0033:0x7fc4480b0690
[  196.253715] RSP: 002b:00007ffde9f252f8 EFLAGS: 00000246 ORIG_RAX: 000000000000002e
[  196.254053] RAX: ffffffffffffffda RBX: 0000000000000040 RCX: 00007fc4480b0690
[  196.254331] RDX: 0000000000000000 RSI: 000000000060a360 RDI: 0000000000000003
[  196.254608] RBP: 00007ffde9f253f0 R08: 00000000002d1e81 R09: 0000000000000002
[  196.254884] R10: 00007ffde9f250c0 R11: 0000000000000246 R12: 0000000000b22070
[  196.255205] R13: 20c49ba5e353f7cf R14: 431bde82d7b634db R15: 00007ffde9f278fe
[  196.255484] Code: a5 0f b6 45 c0 41 88 41 28 41 0f b6 41 2c 48 c1 e0 04 49 8b 54 01 38 49 8b 44 01 30 49 89 51 20 49 89 41 18 48 8b 83 b0 00 00 00 <48> 8b 30 49 8b 86 08 0b 00 00 48 8b 40 20 48 8b 50 08 48 0b 10
[  196.256190] RIP: seg6_do_srh_encap+0x1ac/0x300 RSP: ffffb2ce00b23a60
[  196.256445] CR2: 0000000000000000
[  196.256676] ---[ end trace 71af7d093603885c ]---

Fixes: 8936ef7604c11 ("ipv6: sr: fix NULL pointer dereference when setting encap source address")
Signed-off-by: Ahmed Abdelsalam <amsalam20@gmail.com>
Acked-by: David Lebrun <dlebrun@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

llc: fix NULL pointer deref for SOCK_ZAPPED

For SOCK_ZAPPED socket, we don't need to care about llc->sap,
so we should just skip these refcount functions in this case.

Fixes: f7e43672683b ("llc: hold llc_sap before release_sock()")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: ethernet: ti: cpsw: fix tx vlan priority mapping

The CPDMA_TX_PRIORITY_MAP in real is vlan pcp field priority mapping
register and basically replaces vlan pcp field for tagged packets.
So, set it to be 1:1 mapping. Otherwise, it will cause unexpected
change of egress vlan tagged packets, like prio 2 -> prio 5.

Fixes: e05107e6b747 ("net: ethernet: ti: cpsw: add multi queue support")
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

llc: delete timers synchronously in llc_sk_free()

The connection timers of an llc sock could be still flying
after we delete them in llc_sk_free(), and even possibly
after we free the sock. We could just wait synchronously
here in case of troubles.

Note, I leave other call paths as they are, since they may
not have to wait, at least we can change them to synchronously
when needed.

Also, move the code to net/llc/llc_conn.c, which is apparently
a better place.

Reported-by: <syzbot+f922284c18ea23a8e457@syzkaller.appspotmail.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

l2tp: fix {pppol2tp, l2tp_dfs}_seq_stop() in case of seq_file overflow

Commit 0e0c3fee3a59 ("l2tp: hold reference on tunnels printed in pppol2tp proc file")
assumed that if pppol2tp_seq_stop() was called with non-NULL private
data (the 'v' pointer), then pppol2tp_seq_start() would not be called
again. It turns out that this isn't guaranteed, and overflowing the
seq_file's buffer in pppol2tp_seq_show() is a way to get into this
situation.

Therefore, pppol2tp_seq_stop() needs to reset pd->tunnel, so that
pppol2tp_seq_start() won't drop a reference again if it gets called.
We also have to clear pd->session, because the rest of the code expects
a non-NULL tunnel when pd->session is set.

The l2tp_debugfs module has the same issue. Fix it in the same way.

Fixes: 0e0c3fee3a59 ("l2tp: hold reference on tunnels printed in pppol2tp proc file")
Fixes: f726214d9b23 ("l2tp: hold reference on tunnels printed in l2tp/tunnels debugfs file")
Signed-off-by: Guillaume Nault <g.nault@alphalink.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge branch 's390-qeth-fixes'

Julian Wiedmann says:

====================
s390/qeth: fixes 2018-04-19

Please apply the following qeth fixes for 4.17. The common theme
seems to be error handling improvements in various areas of cmd IO.

Patches 1-3 should also go back to stable.
====================

Signed-off-by: David S. Miller <davem@davemloft.net>

s390/qeth: use Read device to query hypervisor for MAC

For z/VM NICs, qeth needs to consider which of the three CCW devices in
an MPC group it uses for requesting a managed MAC address.

On the Base device, the hypervisor returns a default MAC which is
pre-assigned when creating the NIC (this MAC is also returned by the
READ MAC primitive). Querying any other device results in the allocation
of an additional MAC address.

For consistency with READ MAC and to avoid using up more addresses than
necessary, it is preferable to use the NIC's default MAC. So switch the
the diag26c over to using a NIC's Read device, which should always be
identical to the Base device.

Fixes: ec61bd2fd2a2 ("s390/qeth: use diag26c to get MAC address on L2")
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

s390/qeth: fix request-side race during cmd IO timeout

Submitting a cmd IO request (usually on the WRITE device, but for IDX
also on the READ device) is currently done with ccw_device_start()
and a manual timeout in the caller.
On timeout, the caller cleans up the related resources (eg. IO buffer).
But 1) the IO might still be active and utilize those resources, and
2) when the IO completes, qeth_irq() will attempt to clean up the
same resources again.

Instead of introducing additional resource locking, switch to
ccw_device_start_timeout() to ensure IO termination after timeout, and
let the IRQ handler alone deal with cleaning up after a request.

This also removes a stray write->irq_pending reset from
clear_ipacmd_list(). The routine doesn't terminate any pending IO on
the WRITE device, so this should be handled properly via IO timeout
in the IRQ handler.

Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

s390/qeth: fix MAC address update sequence

When changing the MAC address on a L2 qeth device, current code first
unregisters the old address, then registers the new one.
If HW rejects the new address (or the IO fails), the device ends up with
no operable address at all.

Re-order the code flow so that the old address only gets dropped if the
new address was registered successfully. While at it, add logic to catch
some corner-cases.

Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

s390/qeth: handle failure on workqueue creation

Creating the global workqueue during driver init may fail, deal with it.
Also, destroy the created workqueue on any subsequent error.

Fixes: 0f54761d167f ("qeth: Support VEPA mode")
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

s390/qeth: avoid control IO completion stalls

For control IO, qeth currently tracks the index of the buffer that it
expects to complete the next IO on each qeth_channel. If the channel
presents an IRQ while this buffer has not yet completed, no completion
processing for _any_ completed buffer takes place.
So if the 'next buffer' is skipped for any sort of reason* (eg. when it
is released due to error conditions, before the IO is started), the
buffer obviously won't switch to PROCESSED until it is eventually
allocated for a _different_ IO and completes.
Until this happens, all completion processing on that channel stalls
and pending requests possibly time out.

As a fix, remove the whole 'next buffer' logic and simply process any
IO buffer right when it completes. A channel will never have more than
one IO pending, so there's no risk of processing out-of-sequence.

*Note: currently just one location in the code really handles this problem,
by advancing the 'next' index manually.

Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

s390/qeth: fix error handling in adapter command callbacks

Make sure to check both return code fields before(!) processing the
command response. Otherwise we risk operating on invalid data.

This matches an earlier fix for SETASSPARMS commands, see
commit ad3cbf613329 ("s390/qeth: fix error handling in checksum cmd callback").

Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

bpf: sockmap remove dead check

Remove dead code that bails on `attr->value_size > KMALLOC_MAX_SIZE` - the
previous check already bails on `attr->value_size != 4`.

Signed-off-by: Jann Horn <jannh@google.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>

Merge branch 'fixes' of git://git./linux/kernel/git/evalenti/linux-soc-thermal

Pull thermal fixes from Eduardo Valentin:
"A couple of fixes for the thermal subsystem"

* 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/evalenti/linux-soc-thermal:
dt-bindings: thermal: Remove "cooling-{min|max}-level" properties
dt-bindings: thermal: remove no longer needed samsung thermal properties

Merge tag 'mmc-v4.17-3' of git://git./linux/kernel/git/ulfh/mmc

Pull MMC fixes from Ulf Hansson:
"A couple of MMC host fixes:

   - sdhci-pci: Fixup tuning for AMD for eMMC HS200 mode

   - renesas_sdhi_internal_dmac: Avoid data corruption by limiting
     DMA RX"

* tag 'mmc-v4.17-3' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc:
  mmc: renesas_sdhi_internal_dmac: limit DMA RX for old SoCs
  mmc: sdhci-pci: Only do AMD tuning for HS200

Merge tag 'md/4.17-rc1' of git://git./linux/kernel/git/shli/md

Pull MD fixes from Shaohua Li:
"Three small fixes for MD:

   - md-cluster fix for faulty device from Guoqing

   - writehint fix for writebehind IO for raid1 from Mariusz

   - a live lock fix for interrupted recovery from Yufen"

* tag 'md/4.17-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/shli/md:
  raid1: copy write hint from master bio to behind bio
  md/raid1: exit sync request if MD_RECOVERY_INTR is set
  md-cluster: don't update recovery_offset for faulty device

vfs: Undo an overly zealous MS_RDONLY -> SB_RDONLY conversion

In do_mount() when the MS_* flags are being converted to MNT_* flags,
MS_RDONLY got accidentally convered to SB_RDONLY.

Undo this change.

Fixes: e462ec50cb5f ("VFS: Differentiate mount flags (MS_*) from internal superblock flags")
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

afs: Fix server record deletion

AFS server records get removed from the net->fs_servers tree when
they're deleted, but not from the net->fs_addresses{4,6} lists, which
can lead to an oops in afs_find_server() when a server record has been
removed, for instance during rmmod.

Fix this by deleting the record from the by-address lists before posting
it for RCU destruction.

The reason this hasn't been noticed before is that the fileserver keeps
probing the local cache manager, thereby keeping the service record
alive, so the oops would only happen when a fileserver eventually gets
bored and stops pinging or if the module gets rmmod'd and a call comes
in from the fileserver during the window between the server records
being destroyed and the socket being closed.

The oops looks something like:

  BUG: unable to handle kernel NULL pointer dereference at 000000000000001c
  ...
  Workqueue: kafsd afs_process_async_call [kafs]
  RIP: 0010:afs_find_server+0x271/0x36f [kafs]
  ...
  Call Trace:
   afs_deliver_cb_init_call_back_state3+0x1f2/0x21f [kafs]
   afs_deliver_to_call+0x1ee/0x5e8 [kafs]
   afs_process_async_call+0x5b/0xd0 [kafs]
   process_one_work+0x2c2/0x504
   worker_thread+0x1d4/0x2ac
   kthread+0x11f/0x127
   ret_from_fork+0x24/0x30

Fixes: d2ddc776a458 ("afs: Overhaul volume and server record caching and fileserver rotation")
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Merge git://git./linux/kernel/git/davem/net

Pull networking fixes from David Miller:

1) Unbalanced refcounting in TIPC, from Jon Maloy.

2) Only allow TCP_MD5SIG to be set on sockets in close or listen state.
    Once the connection is established it makes no sense to change this.
    From Eric Dumazet.

3) Missing attribute validation in neigh_dump_table(), also from Eric
    Dumazet.

4) Fix address comparisons in SCTP, from Xin Long.

5) Neigh proxy table clearing can deadlock, from Wolfgang Bumiller.

6) Fix tunnel refcounting in l2tp, from Guillaume Nault.

7) Fix double list insert in team driver, from Paolo Abeni.

8) af_vsock.ko module was accidently made unremovable, from Stefan
    Hajnoczi.

9) Fix reference to freed llc_sap object in llc stack, from Cong Wang.

10) Don't assume netdevice struct is DMA'able memory in virtio_net
    driver, from Michael S. Tsirkin.

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (62 commits)
  net/smc: fix shutdown in state SMC_LISTEN
  bnxt_en: Fix memory fault in bnxt_ethtool_init()
  virtio_net: sparse annotation fix
  virtio_net: fix adding vids on big-endian
  virtio_net: split out ctrl buffer
  net: hns: Avoid action name truncation
  docs: ip-sysctl.txt: fix name of some ipv6 variables
  vmxnet3: fix incorrect dereference when rxvlan is disabled
  llc: hold llc_sap before release_sock()
  MAINTAINERS: Direct networking documentation changes to netdev
  atm: iphase: fix spelling mistake: "Tansmit" -> "Transmit"
  net: qmi_wwan: add Wistron Neweb D19Q1
  net: caif: fix spelling mistake "UKNOWN" -> "UNKNOWN"
  net: stmmac: Disable ACS Feature for GMAC >= 4
  net: mvpp2: Fix DMA address mask size
  net: change the comment of dev_mc_init
  net: qualcomm: rmnet: Fix warning seen with fill_info
  tun: fix vlan packet truncation
  tipc: fix infinite loop when dumping link monitor summary
  tipc: fix use-after-free in tipc_nametbl_stop
  ...

Merge branch 'for-linus' of git://git./linux/kernel/git/viro/vfs

Pull vfs fixes from Al Viro:
"Assorted fixes.

  Some of that is only a matter with fault injection (broken handling of
  small allocation failure in various mount-related places), but the
  last one is a root-triggerable stack overflow, and combined with
  userns it gets really nasty ;-/"

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
  Don't leak MNT_INTERNAL away from internal mounts
  mm,vmscan: Allow preallocating memory for register_shrinker().
  rpc_pipefs: fix double-dput()
  orangefs_kill_sb(): deal with allocation failures
  jffs2_kill_sb(): deal with failed allocations
  hypfs_kill_super(): deal with failed allocations

Merge tag 'ecryptfs-4.17-rc2-fixes' of git://git./linux/kernel/git/tyhicks/ecryptfs

Pull eCryptfs fixes from Tyler Hicks:
"Minor cleanups and a bug fix to completely ignore unencrypted
  filenames in the lower filesystem when filename encryption is enabled
  at the eCryptfs layer"

* tag 'ecryptfs-4.17-rc2-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tyhicks/ecryptfs:
  eCryptfs: don't pass up plaintext names when using filename encryption
  ecryptfs: fix spelling mistake: "cadidate" -> "candidate"
  ecryptfs: lookup: Don't check if mount_crypt_stat is NULL

Merge tag 'for_v4.17-rc2' of git://git./linux/kernel/git/jack/linux-fs

- isofs memory leak fix

- two fsnotify fixes of event mask handling

- udf fix of UTF-16 handling

- couple other smaller cleanups

* tag 'for_v4.17-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/jack/linux-fs:
  udf: Fix leak of UTF-16 surrogates into encoded strings
  fs: ext2: Adding new return type vm_fault_t
  isofs: fix potential memory leak in mount option parsing
  MAINTAINERS: add an entry for FSNOTIFY infrastructure
  fsnotify: fix typo in a comment about mark->g_list
  fsnotify: fix ignore mask logic in send_to_group()
  isofs compress: Remove VLA usage
  fs: quota: Replace GFP_ATOMIC with GFP_KERNEL in dquot_init
  fanotify: fix logic of events on child

Merge branch 'for-linus' of git://git./linux/kernel/git/jikos/hid

Pull HID updates from Jiri Kosina:

- suspend/resume handling fix for Raydium I2C-connected touchscreen
   from Aaron Ma

- protocol fixup for certain BT-connected Wacoms from Aaron Armstrong
   Skomra

- battery level reporting fix on BT-connected mice from Dmitry Torokhov

- hidraw race condition fix from Rodrigo Rivas Costa

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid:
  HID: i2c-hid: fix inverted return value from i2c_hid_command()
  HID: i2c-hid: Fix resume issue on Raydium touchscreen device
  HID: wacom: bluetooth: send exit report for recent Bluetooth devices
  HID: hidraw: Fix crash on HIDIOCGFEATURE with a destroyed device
  HID: input: fix battery level reporting on BT mice

Merge branch 'for-linus' of git://git./linux/kernel/git/jikos/livepatching

Pull livepatching fix from Jiri Kosina:
"Shadow variable API list_head initialization fix from Petr Mladek"

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/livepatching:
livepatch: Allow to call a custom callback when freeing shadow variables
livepatch: Initialize shadow variables safely by a custom callback

Merge tag 'for-linus-4.17-rc2-tag' of git://git./linux/kernel/git/xen/tip

Pull xen fixes from Juergen Gross:

- some fixes of kmalloc() flags

- one fix of the xenbus driver

- an update of the pv sound driver interface needed for a driver which
   will go through the sound tree

* tag 'for-linus-4.17-rc2-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
  xen: xenbus_dev_frontend: Really return response string
  xen/sndif: Sync up with the canonical definition in Xen
  xen: xen-pciback: Replace GFP_ATOMIC with GFP_KERNEL in pcistub_reg_add
  xen: xen-pciback: Replace GFP_ATOMIC with GFP_KERNEL in xen_pcibk_config_quirks_init
  xen: xen-pciback: Replace GFP_ATOMIC with GFP_KERNEL in pcistub_device_alloc
  xen: xen-pciback: Replace GFP_ATOMIC with GFP_KERNEL in pcistub_init_device
  xen: xen-pciback: Replace GFP_ATOMIC with GFP_KERNEL in pcistub_probe

Merge tag 'mips_fixes_4.17_1' of git://git./linux/kernel/git/jhogan/mips

Pull MIPS fixes from James Hogan:

- io: Add barriers to read*() & write*()

- dts: Fix boston PCI bus DTC warnings (4.17)

- memset: Several corner case fixes (one 3.10, others longer)

* tag 'mips_fixes_4.17_1' of git://git.kernel.org/pub/scm/linux/kernel/git/jhogan/mips:
  MIPS: uaccess: Add micromips clobbers to bzero invocation
  MIPS: memset.S: Fix clobber of v1 in last_fixup
  MIPS: memset.S: Fix return of __clear_user from Lpartial_fixup
  MIPS: memset.S: EVA & fault support for small_memset
  MIPS: dts: Boston: Fix PCI bus dtc warnings:
  MIPS: io: Add barrier after register read in readX()
  MIPS: io: Prevent compiler reordering writeX()

Merge tag 'powerpc-4.17-3' of git://git./linux/kernel/git/powerpc/linux

Pull powerpc fixes from Michael Ellerman:

- Fix an off-by-one bug in our alternative asm patching which leads to
   incorrectly patched code. This bug lay dormant for nearly 10 years
   but we finally hit it due to a recent change.

- Fix lockups when running KVM guests on Power8 due to a missing check
   when a thread that's running KVM comes out of idle.

- Fix an out-of-spec behaviour in the XIVE code (P9 interrupt
   controller).

- Fix EEH handling of bridge MMIO windows.

- Prevent crashes in our RFI fallback flush handler if firmware didn't
   tell us the size of the L1 cache (only seen on simulators).

Thanks to: Benjamin Herrenschmidt, Madhavan Srinivasan, Michael Neuling.

* tag 'powerpc-4.17-3' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
  powerpc/kvm: Fix lockups when running KVM guests on Power8
  powerpc/eeh: Fix enabling bridge MMIO windows
  powerpc/xive: Fix trying to "push" an already active pool VP
  powerpc/64s: Default l1d_size to 64K in RFI fallback flush
  powerpc/lib: Fix off-by-one in alternate feature patching

Merge branch 'for-linus' of git://git./linux/kernel/git/s390/linux

Pull s390 fixes and kexec-file-load from Martin Schwidefsky:
"After the common code kexec patches went in via Andrew we can now push
  the architecture parts to implement the kexec-file-load system call.

  Plus a few more bug fixes and cleanups, this includes an update to the
  default configurations"

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
  s390/signal: cleanup uapi struct sigaction
  s390: rename default_defconfig to debug_defconfig
  s390: remove gcov defconfig
  s390: update defconfig
  s390: add support for IBM z14 Model ZR1
  s390: remove couple of duplicate includes
  s390/boot: remove unused COMPILE_VERSION and ccflags-y
  s390/nospec: include cpu.h
  s390/decompressor: Ignore file vmlinux.bin.full
  s390/kexec_file: add generated files to .gitignore
  s390/Kconfig: Move kexec config options to "Processor type and features"
  s390/kexec_file: Add ELF loader
  s390/kexec_file: Add crash support to image loader
  s390/kexec_file: Add image loader
  s390/kexec_file: Add kexec_file_load system call
  s390/kexec_file: Add purgatory
  s390/kexec_file: Prepare setup.h for kexec_file_load
  s390/smsgiucv: disable SMSG on module unload
  s390/sclp: avoid potential usage of uninitialized value

Don't leak MNT_INTERNAL away from internal mounts

We want it only for the stuff created by SB_KERNMOUNT mounts, *not* for
their copies. As it is, creating a deep stack of bindings of /proc/*/ns/*
somewhere in a new namespace and exiting yields a stack overflow.

Cc: stable@kernel.org
Reported-by: Alexander Aring <aring@mojatatu.com>
Bisected-by: Kirill Tkhai <ktkhai@virtuozzo.com>
Tested-by: Kirill Tkhai <ktkhai@virtuozzo.com>
Tested-by: Alexander Aring <aring@mojatatu.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>

net/smc: fix shutdown in state SMC_LISTEN

Calling shutdown with SHUT_RD and SHUT_RDWR for a listening SMC socket
crashes, because
commit 127f49705823 ("net/smc: release clcsock from tcp_listen_worker")
releases the internal clcsock in smc_close_active() and sets smc->clcsock
to NULL.
For SHUT_RD the smc_close_active() call is removed.
For SHUT_RDWR the kernel_sock_shutdown() call is omitted, since the
clcsock is already released.

Fixes: 127f49705823 ("net/smc: release clcsock from tcp_listen_worker")
Signed-off-by: Ursula Braun <ubraun@linux.vnet.ibm.com>
Reported-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

bnxt_en: Fix memory fault in bnxt_ethtool_init()

In some firmware images, the length of BNX_DIR_TYPE_PKG_LOG nvram type
could be greater than the fixed buffer length of 4096 bytes allocated by
the driver. This was causing HWRM_NVM_READ to copy more data to the buffer
than the allocated size, causing general protection fault.

Fix the issue by allocating the exact buffer length returned by
HWRM_NVM_FIND_DIR_ENTRY, instead of 4096. Move the kzalloc() call
into the bnxt_get_pkgver() function.

Fixes: 3ebf6f0a09a2 ("bnxt_en: Add installed-package firmware version reporting via Ethtool GDRVINFO")
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge branch 'virtio-ctrl-buffer-fixes'

Michael S. Tsirkin says:

====================
virtio: ctrl buffer fixes

Here are a couple of fixes related to the virtio control buffer.
Lightly tested on x86 only.
====================

Signed-off-by: David S. Miller <davem@davemloft.net>

virtio_net: sparse annotation fix

offloads is a buffer in virtio format, should use
the __virtio64 tag.

Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

virtio_net: fix adding vids on big-endian

Programming vids (adding or removing them) still passes
guest-endian values in the DMA buffer. That's wrong
if guest is big-endian and when virtio 1 is enabled.

Note: this is on top of a previous patch:
virtio_net: split out ctrl buffer

Fixes: 9465a7a6f ("virtio_net: enable v1.0 support")
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

virtio_net: split out ctrl buffer

When sending control commands, virtio net sets up several buffers for
DMA. The buffers are all part of the net device which means it's
actually allocated by kvmalloc so it's in theory (on extreme memory
pressure) possible to get a vmalloc'ed buffer which on some platforms
means we can't DMA there.

Fix up by moving the DMA buffers into a separate structure.

Reported-by: Mikulas Patocka <mpatocka@redhat.com>
Suggested-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: hns: Avoid action name truncation

When longer interface names are used, the action names exposed in
/proc/interrupts and /proc/irq/* maybe truncated. For example, when
using the predictable name algorithm in systemd on a HiSilicon D05,
I see:

  ubuntu@d05-3:~$  grep enahisic2i0-tx /proc/interrupts | sed 's/.* //'
  enahisic2i0-tx0
  enahisic2i0-tx1
  [...]
  enahisic2i0-tx8
  enahisic2i0-tx9
  enahisic2i0-tx1
  enahisic2i0-tx1
  enahisic2i0-tx1
  enahisic2i0-tx1
  enahisic2i0-tx1
  enahisic2i0-tx1

Increase the max ring name length to allow for an interface name
of IFNAMSIZE. After this change, I now see:

  $ grep enahisic2i0-tx /proc/interrupts | sed 's/.* //'
  enahisic2i0-tx0
  enahisic2i0-tx1
  enahisic2i0-tx2
  [...]
  enahisic2i0-tx8
  enahisic2i0-tx9
  enahisic2i0-tx10
  enahisic2i0-tx11
  enahisic2i0-tx12
  enahisic2i0-tx13
  enahisic2i0-tx14
  enahisic2i0-tx15

Signed-off-by: dann frazier <dann.frazier@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

docs: ip-sysctl.txt: fix name of some ipv6 variables

The name of the following proc/sysctl entries were incorrectly
documented:

    /proc/sys/net/ipv6/conf/<interface>/max_dst_opts_number
    /proc/sys/net/ipv6/conf/<interface>/max_hbt_opts_number
    /proc/sys/net/ipv6/conf/<interface>/max_dst_opts_length
    /proc/sys/net/ipv6/conf/<interface>/max_hbt_length

Their name was set to the name of the symbol in the .data field of the
control table instead of their .proc name.

Signed-off-by: Olivier Gayot <olivier.gayot@sigexec.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

vmxnet3: fix incorrect dereference when rxvlan is disabled

vmxnet3_get_hdr_len() is used to calculate the header length which in
turn is used to calculate the gso_size for skb. When rxvlan offload is
disabled, vlan tag is present in the header and the function references
ip header from sizeof(ethhdr) and leads to incorrect pointer reference.

This patch fixes this issue by taking sizeof(vlan_ethhdr) into account
if vlan tag is present and correctly references the ip hdr.

Signed-off-by: Ronak Doshi <doshir@vmware.com>
Acked-by: Guolin Yang <gyang@vmware.com>
Acked-by: Louis Luo <llouis@vmware.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

llc: hold llc_sap before release_sock()

syzbot reported we still access llc->sap in llc_backlog_rcv()
after it is freed in llc_sap_remove_socket():

Call Trace:
__dump_stack lib/dump_stack.c:77 [inline]
dump_stack+0x1b9/0x294 lib/dump_stack.c:113
print_address_description+0x6c/0x20b mm/kasan/report.c:256
kasan_report_error mm/kasan/report.c:354 [inline]
kasan_report.cold.7+0x242/0x2fe mm/kasan/report.c:412
__asan_report_load1_noabort+0x14/0x20 mm/kasan/report.c:430
llc_conn_ac_send_sabme_cmd_p_set_x+0x3a8/0x460 net/llc/llc_c_ac.c:785
llc_exec_conn_trans_actions net/llc/llc_conn.c:475 [inline]
llc_conn_service net/llc/llc_conn.c:400 [inline]
llc_conn_state_process+0x4e1/0x13a0 net/llc/llc_conn.c:75
llc_backlog_rcv+0x195/0x1e0 net/llc/llc_conn.c:891
sk_backlog_rcv include/net/sock.h:909 [inline]
__release_sock+0x12f/0x3a0 net/core/sock.c:2335
release_sock+0xa4/0x2b0 net/core/sock.c:2850
llc_ui_release+0xc8/0x220 net/llc/af_llc.c:204

llc->sap is refcount'ed and llc_sap_remove_socket() is paired
with llc_sap_add_socket(). This can be amended by holding its refcount
before llc_sap_remove_socket() and releasing it after release_sock().

Reported-by: <syzbot+6e181fc95081c2cf9051@syzkaller.appspotmail.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

MAINTAINERS: Direct networking documentation changes to netdev

Networking docs changes go through the networking tree, so patch the
MAINTAINERS file to direct authors to the right place.

Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

atm: iphase: fix spelling mistake: "Tansmit" -> "Transmit"

Trivial fix to spelling mistake in message text.

Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: qmi_wwan: add Wistron Neweb D19Q1

This modem is embedded on dlink dwr-960 router.
The oem configuration states:

T: Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 2 Spd=480 MxCh= 0
D: Ver= 2.10 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1
P: Vendor=1435 ProdID=d191 Rev=ff.ff
S: Manufacturer=Android
S: Product=Android
S: SerialNumber=0123456789ABCDEF
C:* #Ifs= 6 Cfg#= 1 Atr=80 MxPwr=500mA
I:* If#= 0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)
E: Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=42 Prot=01 Driver=(none)
E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=(none)
E: Ad=84(I) Atr=03(Int.) MxPS= 10 Ivl=32ms
E: Ad=83(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=(none)
E: Ad=86(I) Atr=03(Int.) MxPS= 10 Ivl=32ms
E: Ad=85(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=04(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 4 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=qmi_wwan
E: Ad=88(I) Atr=03(Int.) MxPS= 8 Ivl=32ms
E: Ad=87(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=05(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 5 Alt= 0 #EPs= 2 Cls=08(stor.) Sub=06 Prot=50 Driver=(none)
E: Ad=89(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=06(O) Atr=02(Bulk) MxPS= 512 Ivl=125us

Tested on openwrt distribution

Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
Acked-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: caif: fix spelling mistake "UKNOWN" -> "UNKNOWN"

Trivial fix to spelling mistake

Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: stmmac: Disable ACS Feature for GMAC >= 4

ACS Feature is currently enabled for GMAC >= 4 but the llc_snap status
is never checked in descriptor rx_status callback. This will cause
stmmac to always strip packets even that ACS feature is already
stripping them.

Lets be safe and disable the ACS feature for GMAC >= 4 and always strip
the packets for this GMAC version.

Fixes: 477286b53f55 ("stmmac: add GMAC4 core support")
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Joao Pinto <jpinto@synopsys.com>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: mvpp2: Fix DMA address mask size

PPv2 TX/RX descriptors uses 40bits DMA addresses, but 41 bits masks were
used (GENMASK_ULL(40, 0)).

This commit fixes that by using the correct mask.

Fixes: e7c5359f2eed ("net: mvpp2: introduce PPv2.2 HW descriptors and adapt accessors")
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: change the comment of dev_mc_init

The comment of dev_mc_init() is wrong. which use dev_mc_flush
instead of dev_mc_init.

Signed-off-by: Lianwen Sun <sunlw.fnst@cn.fujitsu.com
Signed-off-by: David S. Miller <davem@davemloft.net>

netfilter: xt_connmark: do not cast xt_connmark_tginfo1 to xt_connmark_tginfo2

These structures have different layout, fill xt_connmark_tginfo2 with
old fields in xt_connmark_tginfo1. Based on patch from Jack Ma.

Fixes: 472a73e00757 ("netfilter: xt_conntrack: Support bit-shifting for CONNMARK & MARK targets.")
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>

mmc: renesas_sdhi_internal_dmac: limit DMA RX for old SoCs

Early revisions of certain SoCs cannot do multiple DMA RX streams in
parallel. To avoid data corruption, only allow one DMA RX channel and
fall back to PIO, if needed.

Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Tested-by: Nguyen Viet Dung <dung.nguyen.aj@renesas.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Cc: stable@vger.kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

netfilter: nf_tables: fix out-of-bounds in nft_chain_commit_update

When chain name is changed, nft_chain_commit_update is called.
In the nft_chain_commit_update, trans->ctx.chain->name has old chain name
and nft_trans_chain_name(trans) has new chain name.
If new chain name is longer than old chain name, KASAN warns
slab-out-of-bounds.

[  175.015012] BUG: KASAN: slab-out-of-bounds in strcpy+0x9e/0xb0
[  175.022735] Write of size 1 at addr ffff880114e022da by task iptables-compat/1458

[  175.031353] CPU: 0 PID: 1458 Comm: iptables-compat Not tainted 4.16.0-rc7+ #146
[  175.031353] Hardware name: To be filled by O.E.M. To be filled by O.E.M./Aptio CRB, BIOS 5.6.5 07/08/2015
[  175.031353] Call Trace:
[  175.031353]  dump_stack+0x68/0xa0
[  175.031353]  print_address_description+0xd0/0x260
[  175.031353]  ? strcpy+0x9e/0xb0
[  175.031353]  kasan_report+0x234/0x350
[  175.031353]  __asan_report_store1_noabort+0x1c/0x20
[  175.031353]  strcpy+0x9e/0xb0
[  175.031353]  nf_tables_commit+0x1ccc/0x2990
[  175.031353]  nfnetlink_rcv+0x141e/0x16c0
[  175.031353]  ? nfnetlink_net_init+0x150/0x150
[  175.031353]  ? lock_acquire+0x370/0x370
[  175.031353]  ? lock_acquire+0x370/0x370
[  175.031353]  netlink_unicast+0x444/0x640
[  175.031353]  ? netlink_attachskb+0x700/0x700
[  175.031353]  ? _copy_from_iter_full+0x180/0x740
[  175.031353]  ? kasan_check_write+0x14/0x20
[  175.031353]  ? _copy_from_user+0x9b/0xd0
[  175.031353]  netlink_sendmsg+0x845/0xc70
[ ... ]

Steps to reproduce:
   iptables-compat -N 1
   iptables-compat -E 1 aaaaaaaaa

Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>

netfilter: nf_tables: NAT chain and extensions require NF_TABLES

Move these options inside the scope of the 'if' NF_TABLES and
NF_TABLES_IPV6 dependencies. This patch fixes:

   net/ipv6/netfilter/nft_chain_nat_ipv6.o: In function `nft_nat_do_chain':
>> net/ipv6/netfilter/nft_chain_nat_ipv6.c:37: undefined reference to `nft_do_chain'
   net/ipv6/netfilter/nft_chain_nat_ipv6.o: In function `nft_chain_nat_ipv6_exit':
>> net/ipv6/netfilter/nft_chain_nat_ipv6.c:94: undefined reference to `nft_unregister_chain_type'
   net/ipv6/netfilter/nft_chain_nat_ipv6.o: In function `nft_chain_nat_ipv6_init':
>> net/ipv6/netfilter/nft_chain_nat_ipv6.c:87: undefined reference to `nft_register_chain_type'

that happens with:

CONFIG_NF_TABLES=m
CONFIG_NFT_CHAIN_NAT_IPV6=y

Fixes: 02c7b25e5f54 ("netfilter: nf_tables: build-in filter chain type")
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>

HID: i2c-hid: fix inverted return value from i2c_hid_command()

i2c_hid_command() returns non-zero in error cases (the actual
errno). Error handling in for I2C_HID_QUIRK_RESEND_REPORT_DESCR
case in i2c_hid_resume() had the check inverted; fix that.

Fixes: 3e83eda467 ("HID: i2c-hid: Fix resume issue on Raydium touchscreen device")
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>

powerpc/kvm: Fix lockups when running KVM guests on Power8

When running KVM guests on Power8 we can see a lockup where one CPU
stops responding. This often leads to a message such as:

  watchdog: CPU 136 detected hard LOCKUP on other CPUs 72
  Task dump for CPU 72:
  qemu-system-ppc R  running task    10560 20917  20908 0x00040004

And then backtraces on other CPUs, such as:

  Task dump for CPU 48:
  ksmd            R  running task    10032  1519      2 0x00000804
  Call Trace:
    ...
    --- interrupt: 901 at smp_call_function_many+0x3c8/0x460
        LR = smp_call_function_many+0x37c/0x460
    pmdp_invalidate+0x100/0x1b0
    __split_huge_pmd+0x52c/0xdb0
    try_to_unmap_one+0x764/0x8b0
    rmap_walk_anon+0x15c/0x370
    try_to_unmap+0xb4/0x170
    split_huge_page_to_list+0x148/0xa30
    try_to_merge_one_page+0xc8/0x990
    try_to_merge_with_ksm_page+0x74/0xf0
    ksm_scan_thread+0x10ec/0x1ac0
    kthread+0x160/0x1a0
    ret_from_kernel_thread+0x5c/0x78

This is caused by commit 8c1c7fb0b5ec ("powerpc/64s/idle: avoid sync
for KVM state when waking from idle"), which added a check in
pnv_powersave_wakeup() to see if the kvm_hstate.hwthread_state is
already set to KVM_HWTHREAD_IN_KERNEL, and if so to skip the store and
test of kvm_hstate.hwthread_req.

The problem is that the primary does not set KVM_HWTHREAD_IN_KVM when
entering the guest, so it can then come out to cede with
KVM_HWTHREAD_IN_KERNEL set. It can then go idle in kvm_do_nap after
setting hwthread_req to 1, but because hwthread_state is still
KVM_HWTHREAD_IN_KERNEL we will skip the test of hwthread_req when we
wake up from idle and won't go to kvm_start_guest. From there the
thread will return somewhere garbage and crash.

Fix it by skipping the store of hwthread_state, but not the test of
hwthread_req, when coming out of idle. It's OK to skip the sync in
that case because hwthread_req will have been set on the same thread,
so there is no synchronisation required.

Fixes: 8c1c7fb0b5ec ("powerpc/64s/idle: avoid sync for KVM state when waking from idle")
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

powerpc/eeh: Fix enabling bridge MMIO windows

On boot we save the configuration space of PCIe bridges. We do this so
when we get an EEH event and everything gets reset that we can restore
them.

Unfortunately we save this state before we've enabled the MMIO space
on the bridges. Hence if we have to reset the bridge when we come back
MMIO is not enabled and we end up taking an PE freeze when the driver
starts accessing again.

This patch forces the memory/MMIO and bus mastering on when restoring
bridges on EEH. Ideally we'd do this correctly by saving the
configuration space writes later, but that will have to come later in
a larger EEH rewrite. For now we have this simple fix.

The original bug can be triggered on a boston machine by doing:
echo 0x8000000000000000 > /sys/kernel/debug/powerpc/PCI0001/err_injct_outbound
On boston, this PHB has a PCIe switch on it. Without this patch,
you'll see two EEH events, 1 expected and 1 the failure we are fixing
here. The second EEH event causes the anything under the PHB to
disappear (i.e. the i40e eth).

With this patch, only 1 EEH event occurs and devices properly recover.

Fixes: 652defed4875 ("powerpc/eeh: Check PCIe link after reset")
Cc: stable@vger.kernel.org # v3.11+
Reported-by: Pridhiviraj Paidipeddi <ppaidipe@linux.vnet.ibm.com>
Signed-off-by: Michael Neuling <mikey@neuling.org>
Acked-by: Russell Currey <ruscur@russell.cc>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

net: qualcomm: rmnet: Fix warning seen with fill_info

When the last rmnet device attached to a real device is removed, the
real device is unregistered from rmnet. As a result, the real device
lookup fails resulting in a warning when the fill_info handler is
called as part of the rmnet device unregistration.

Fix this by returning the rmnet flags as 0 when no real device is
present.

WARNING: CPU: 0 PID: 1779 at net/core/rtnetlink.c:3254
rtmsg_ifinfo_build_skb+0xca/0x10d
Modules linked in:
CPU: 0 PID: 1779 Comm: ip Not tainted 4.16.0-11872-g7ce2367 #1
Stack:
7fe655f0 60371ea3 00000000 00000000
60282bc6 6006b116 7fe65600 60371ee8
7fe65660 6003a68c 00000000 900000000
Call Trace:
[<6006b116>] ? printk+0x0/0x94
[<6001f375>] show_stack+0xfe/0x158
[<60371ea3>] ? dump_stack_print_info+0xe8/0xf1
[<60282bc6>] ? rtmsg_ifinfo_build_skb+0xca/0x10d
[<6006b116>] ? printk+0x0/0x94
[<60371ee8>] dump_stack+0x2a/0x2c
[<6003a68c>] __warn+0x10e/0x13e
[<6003a82c>] warn_slowpath_null+0x48/0x4f
[<60282bc6>] rtmsg_ifinfo_build_skb+0xca/0x10d
[<60282c4d>] rtmsg_ifinfo_event.part.37+0x1e/0x43
[<60282c2f>] ? rtmsg_ifinfo_event.part.37+0x0/0x43
[<60282d03>] rtmsg_ifinfo+0x24/0x28
[<60264e86>] dev_close_many+0xba/0x119
[<60282cdf>] ? rtmsg_ifinfo+0x0/0x28
[<6027c225>] ? rtnl_is_locked+0x0/0x1c
[<6026ca67>] rollback_registered_many+0x1ae/0x4ae
[<600314be>] ? unblock_signals+0x0/0xae
[<6026cdc0>] ? unregister_netdevice_queue+0x19/0xec
[<6026ceec>] unregister_netdevice_many+0x21/0xa1
[<6027c765>] rtnl_delete_link+0x3e/0x4e
[<60280ecb>] rtnl_dellink+0x262/0x29c
[<6027c241>] ? rtnl_get_link+0x0/0x3e
[<6027f867>] rtnetlink_rcv_msg+0x235/0x274

Fixes: be81a85f5f87 ("net: qualcomm: rmnet: Implement fill_info")
Signed-off-by: Subash Abhinov Kasiviswanathan <subashab@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

tools/bpf: fix test_sock and test_sock_addr.sh failure

The bpf selftests test_sock and test_sock_addr.sh failed
in my test machine. The failure looks like:
    $ ./test_sock
    Test case: bind4 load with invalid access: src_ip6 .. [PASS]
    Test case: bind4 load with invalid access: mark .. [PASS]
    Test case: bind6 load with invalid access: src_ip4 .. [PASS]
    Test case: sock_create load with invalid access: src_port .. [PASS]
    Test case: sock_create load w/o expected_attach_type (compat mode) .. [FAIL]
    Test case: sock_create load w/ expected_attach_type .. [FAIL]
    Test case: attach type mismatch bind4 vs bind6 .. [FAIL]
    ...
    Summary: 4 PASSED, 12 FAILED
    $ ./test_sock_addr.sh
    Wait for testing IPv4/IPv6 to become available .....
    ERROR: Timeout waiting for test IP to become available.

In test_sock, bpf program loads failed due to hitting memlock limits.
In test_sock_addr.sh, my test machine is a ipv6 only test box and using
"ping" without specifying address family for an ipv6 address does not work.

This patch fixed the issue by including header bpf_rlimit.h in test_sock.c
and test_sock_addr.c, and specifying address family for ping command.

Cc: Andrey Ignatov <rdna@fb.com>
Signed-off-by: Yonghong Song <yhs@fb.com>
Acked-by: Andrey Ignatov <rdna@fb.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>

MIPS: uaccess: Add micromips clobbers to bzero invocation

The micromips implementation of bzero additionally clobbers registers t7
& t8. Specify this in the clobbers list when invoking bzero.

Fixes: 26c5e07d1478 ("MIPS: microMIPS: Optimise 'memset' core library function.")
Reported-by: James Hogan <jhogan@kernel.org>
Signed-off-by: Matt Redfearn <matt.redfearn@mips.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-mips@linux-mips.org
Cc: <stable@vger.kernel.org> # 3.10+
Patchwork: https://patchwork.linux-mips.org/patch/19110/
Signed-off-by: James Hogan <jhogan@kernel.org>

MIPS: memset.S: Fix clobber of v1 in last_fixup

The label .Llast_fixup\@ is jumped to on page fault within the final
byte set loop of memset (on < MIPSR6 architectures). For some reason, in
this fault handler, the v1 register is randomly set to a2 & STORMASK.
This clobbers v1 for the calling function. This can be observed with the
following test code:

static int __init __attribute__((optimize("O0"))) test_clear_user(void)
{
  register int t asm("v1");
  char *test;
  int j, k;

  pr_info("\n\n\nTesting clear_user\n");
  test = vmalloc(PAGE_SIZE);

  for (j = 256; j < 512; j++) {
    t = 0xa5a5a5a5;
    if ((k = clear_user(test + PAGE_SIZE - 256, j)) != j - 256) {
        pr_err("clear_user (%px %d) returned %d\n", test + PAGE_SIZE - 256, j, k);
    }
    if (t != 0xa5a5a5a5) {
       pr_err("v1 was clobbered to 0x%x!\n", t);
    }
  }

  return 0;
}
late_initcall(test_clear_user);

Which demonstrates that v1 is indeed clobbered (MIPS64):

Testing clear_user
v1 was clobbered to 0x1!
v1 was clobbered to 0x2!
v1 was clobbered to 0x3!
v1 was clobbered to 0x4!
v1 was clobbered to 0x5!
v1 was clobbered to 0x6!
v1 was clobbered to 0x7!

Since the number of bytes that could not be set is already contained in
a2, the andi placing a value in v1 is not necessary and actively
harmful in clobbering v1.

Reported-by: James Hogan <jhogan@kernel.org>
Signed-off-by: Matt Redfearn <matt.redfearn@mips.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-mips@linux-mips.org
Cc: stable@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/19109/
Signed-off-by: James Hogan <jhogan@kernel.org>

Merge tag 'ceph-for-4.17-rc2' of git://github.com/ceph/ceph-client

Pull ceph fixes from Ilya Dryomov:
"A couple of follow-up patches for -rc1 changes in rbd, support for a
  timeout on waiting for the acquisition of exclusive lock and a fix for
  uninitialized memory access in CephFS, marked for stable"

* tag 'ceph-for-4.17-rc2' of git://github.com/ceph/ceph-client:
  rbd: notrim map option
  rbd: adjust queue limits for "fancy" striping
  rbd: avoid Wreturn-type warnings
  ceph: always update atime/mtime/ctime for new inode
  rbd: support timeout in rbd_wait_state_locked()
  rbd: refactor rbd_wait_state_locked()

tun: fix vlan packet truncation

Bogus trimming in tun_net_xmit() causes truncated vlan packets.

skb->len is correct whether or not skb_vlan_tag_present() is true. There
is no more reason to adjust the skb length on xmit in this driver than
any other driver. tun_put_user() adds 4 bytes to the total for tagged
packets because it transmits the tag inline to userspace.  This is
similar to a nic transmitting the tag inline on the wire.

Reproducing the bug by sending any tagged packet through back-to-back
connected tap interfaces:

socat TUN,tun-type=tap,iff-up,tun-name=in TUN,tun-type=tap,iff-up,tun-name=out &
ip link add link in name in.20 type vlan id 20
ip addr add 10.9.9.9/24 dev in.20
ip link set in.20 up
tshark -nxxi in -f arp -c1 2>/dev/null &
tshark -nxxi out -f arp -c1 2>/dev/null &
ping -c 1 10.9.9.5 >/dev/null 2>&1

The output from the 'in' and 'out' interfaces are different when the
bug is present:

Capturing on 'in'
0000  ff ff ff ff ff ff 76 cf 76 37 d5 0a 81 00 00 14   ......v.v7......
0010  08 06 00 01 08 00 06 04 00 01 76 cf 76 37 d5 0a   ..........v.v7..
0020  0a 09 09 09 00 00 00 00 00 00 0a 09 09 05         ..............

Capturing on 'out'
0000  ff ff ff ff ff ff 76 cf 76 37 d5 0a 81 00 00 14   ......v.v7......
0010  08 06 00 01 08 00 06 04 00 01 76 cf 76 37 d5 0a   ..........v.v7..
0020  0a 09 09 09 00 00 00 00 00 00                     ..........

Fixes: aff3d70a07ff ("tun: allow to attach ebpf socket filter")
Cc: Jason Wang <jasowang@redhat.com>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Acked-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

tipc: fix infinite loop when dumping link monitor summary

When configuring the number of used bearers to MAX_BEARER and issuing
command "tipc link monitor summary", the command enters infinite loop
in user space.

This issue happens because function tipc_nl_node_dump_monitor() returns
the wrong 'prev_bearer' value when all potential monitors have been
scanned.

The correct behavior is to always try to scan all monitors until either
the netlink message is full, in which case we return the bearer identity
of the affected monitor, or we continue through the whole bearer array
until we can return MAX_BEARERS. This solution also caters for the case
where there may be gaps in the bearer array.

Signed-off-by: Tung Nguyen <tung.q.nguyen@dektech.com.au>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

tipc: fix use-after-free in tipc_nametbl_stop

When we delete a service item in tipc_nametbl_stop() we loop over
all service ranges in the service's RB tree, and for each service
range we loop over its pertaining publications while calling
tipc_service_remove_publ() for each of them.

However, tipc_service_remove_publ() has the side effect that it also
removes the comprising service range item when there are no publications
left. This leads to a "use-after-free" access when the inner loop
continues to the next iteration, since the range item holding the list
we are looping no longer exists.

We fix this by moving the delete of the service range item outside
the said function. Instead, we now let the two functions calling it
test if the list is empty and perform the removal when that is the
case.

Reported-by: syzbot+d64b64afc55660106556@syzkaller.appspotmail.com
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

powerpc/xive: Fix trying to "push" an already active pool VP

When setting up a CPU, we "push" (activate) a pool VP for it.

However it's an error to do so if it already has an active
pool VP.

This happens when doing soft CPU hotplug on powernv since we
don't tear down the CPU on unplug. The HW flags the error which
gets captured by the diagnostics.

Fix this by making sure to "pull" out any already active pool
first.

Fixes: 243e25112d06 ("powerpc/xive: Native exploitation of the XIVE interrupt controller")
Cc: stable@vger.kernel.org # v4.12+
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

udf: Fix leak of UTF-16 surrogates into encoded strings

OSTA UDF specification does not mention whether the CS0 charset in case
of two bytes per character encoding should be treated in UTF-16 or
UCS-2. The sample code in the standard does not treat UTF-16 surrogates
in any special way but on systems such as Windows which work in UTF-16
internally, filenames would be treated as being in UTF-16 effectively.
In Linux it is more difficult to handle characters outside of Base
Multilingual plane (beyond 0xffff) as NLS framework works with 2-byte
characters only. Just make sure we don't leak UTF-16 surrogates into the
resulting string when loading names from the filesystem for now.

CC: stable@vger.kernel.org # >= v4.6
Reported-by: Mingye Wang <arthur200126@gmail.com>
Signed-off-by: Jan Kara <jack@suse.cz>

dt-bindings: thermal: Remove "cooling-{min|max}-level" properties

The "cooling-min-level" and "cooling-max-level" properties are not
parsed by any part of kernel currently and the max cooling state of a
CPU cooling device is found by referring to the cpufreq table instead.

Remove the unused bindings.

Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>

dt-bindings: thermal: remove no longer needed samsung thermal properties

Remove documentation for longer needed samsung thermal properties.

Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>

KEYS: DNS: limit the length of option strings

Adding a dns_resolver key whose payload contains a very long option name
resulted in that string being printed in full.  This hit the WARN_ONCE()
in set_precision() during the printk(), because printk() only supports a
precision of up to 32767 bytes:

    precision 1000000 too large
    WARNING: CPU: 0 PID: 752 at lib/vsprintf.c:2189 vsnprintf+0x4bc/0x5b0

Fix it by limiting option strings (combined name + value) to a much more
reasonable 128 bytes.  The exact limit is arbitrary, but currently the
only recognized option is formatted as "dnserror=%lu" which fits well
within this limit.

Also ratelimit the printks.

Reproducer:

    perl -e 'print "#", "A" x 1000000, "\x00"' | keyctl padd dns_resolver desc @s

This bug was found using syzkaller.

Reported-by: Mark Rutland <mark.rutland@arm.com>
Fixes: 4a2d789267e0 ("DNS: If the DNS server returns an error, allow that to be cached [ver #2]")
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

sfc: check RSS is active for filter insert

For some firmware variants - specifically 'capture packed stream' - RSS
filters are not valid. We must check if RSS is actually active rather
than merely enabled.

Fixes: 42356d9a137b ("sfc: support RSS spreading of ethtool ntuple filters")
Signed-off-by: Bert Kenward <bkenward@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

vlan: Fix reading memory beyond skb->tail in skb_vlan_tagged_multi

Syzkaller spotted an old bug which leads to reading skb beyond tail by 4
bytes on vlan tagged packets.
This is caused because skb_vlan_tagged_multi() did not check
skb_headlen.

BUG: KMSAN: uninit-value in eth_type_vlan include/linux/if_vlan.h:283 [inline]
BUG: KMSAN: uninit-value in skb_vlan_tagged_multi include/linux/if_vlan.h:656 [inline]
BUG: KMSAN: uninit-value in vlan_features_check include/linux/if_vlan.h:672 [inline]
BUG: KMSAN: uninit-value in dflt_features_check net/core/dev.c:2949 [inline]
BUG: KMSAN: uninit-value in netif_skb_features+0xd1b/0xdc0 net/core/dev.c:3009
CPU: 1 PID: 3582 Comm: syzkaller435149 Not tainted 4.16.0+ #82
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
Call Trace:
  __dump_stack lib/dump_stack.c:17 [inline]
  dump_stack+0x185/0x1d0 lib/dump_stack.c:53
  kmsan_report+0x142/0x240 mm/kmsan/kmsan.c:1067
  __msan_warning_32+0x6c/0xb0 mm/kmsan/kmsan_instr.c:676
  eth_type_vlan include/linux/if_vlan.h:283 [inline]
  skb_vlan_tagged_multi include/linux/if_vlan.h:656 [inline]
  vlan_features_check include/linux/if_vlan.h:672 [inline]
  dflt_features_check net/core/dev.c:2949 [inline]
  netif_skb_features+0xd1b/0xdc0 net/core/dev.c:3009
  validate_xmit_skb+0x89/0x1320 net/core/dev.c:3084
  __dev_queue_xmit+0x1cb2/0x2b60 net/core/dev.c:3549
  dev_queue_xmit+0x4b/0x60 net/core/dev.c:3590
  packet_snd net/packet/af_packet.c:2944 [inline]
  packet_sendmsg+0x7c57/0x8a10 net/packet/af_packet.c:2969
  sock_sendmsg_nosec net/socket.c:630 [inline]
  sock_sendmsg net/socket.c:640 [inline]
  sock_write_iter+0x3b9/0x470 net/socket.c:909
  do_iter_readv_writev+0x7bb/0x970 include/linux/fs.h:1776
  do_iter_write+0x30d/0xd40 fs/read_write.c:932
  vfs_writev fs/read_write.c:977 [inline]
  do_writev+0x3c9/0x830 fs/read_write.c:1012
  SYSC_writev+0x9b/0xb0 fs/read_write.c:1085
  SyS_writev+0x56/0x80 fs/read_write.c:1082
  do_syscall_64+0x309/0x430 arch/x86/entry/common.c:287
  entry_SYSCALL_64_after_hwframe+0x3d/0xa2
RIP: 0033:0x43ffa9
RSP: 002b:00007fff2cff3948 EFLAGS: 00000217 ORIG_RAX: 0000000000000014
RAX: ffffffffffffffda RBX: 00000000004002c8 RCX: 000000000043ffa9
RDX: 0000000000000001 RSI: 0000000020000080 RDI: 0000000000000003
RBP: 00000000006cb018 R08: 0000000000000000 R09: 0000000000000000
R10: 0000000000000000 R11: 0000000000000217 R12: 00000000004018d0
R13: 0000000000401960 R14: 0000000000000000 R15: 0000000000000000

Uninit was created at:
  kmsan_save_stack_with_flags mm/kmsan/kmsan.c:278 [inline]
  kmsan_internal_poison_shadow+0xb8/0x1b0 mm/kmsan/kmsan.c:188
  kmsan_kmalloc+0x94/0x100 mm/kmsan/kmsan.c:314
  kmsan_slab_alloc+0x11/0x20 mm/kmsan/kmsan.c:321
  slab_post_alloc_hook mm/slab.h:445 [inline]
  slab_alloc_node mm/slub.c:2737 [inline]
  __kmalloc_node_track_caller+0xaed/0x11c0 mm/slub.c:4369
  __kmalloc_reserve net/core/skbuff.c:138 [inline]
  __alloc_skb+0x2cf/0x9f0 net/core/skbuff.c:206
  alloc_skb include/linux/skbuff.h:984 [inline]
  alloc_skb_with_frags+0x1d4/0xb20 net/core/skbuff.c:5234
  sock_alloc_send_pskb+0xb56/0x1190 net/core/sock.c:2085
  packet_alloc_skb net/packet/af_packet.c:2803 [inline]
  packet_snd net/packet/af_packet.c:2894 [inline]
  packet_sendmsg+0x6444/0x8a10 net/packet/af_packet.c:2969
  sock_sendmsg_nosec net/socket.c:630 [inline]
  sock_sendmsg net/socket.c:640 [inline]
  sock_write_iter+0x3b9/0x470 net/socket.c:909
  do_iter_readv_writev+0x7bb/0x970 include/linux/fs.h:1776
  do_iter_write+0x30d/0xd40 fs/read_write.c:932
  vfs_writev fs/read_write.c:977 [inline]
  do_writev+0x3c9/0x830 fs/read_write.c:1012
  SYSC_writev+0x9b/0xb0 fs/read_write.c:1085
  SyS_writev+0x56/0x80 fs/read_write.c:1082
  do_syscall_64+0x309/0x430 arch/x86/entry/common.c:287
  entry_SYSCALL_64_after_hwframe+0x3d/0xa2

Fixes: 58e998c6d239 ("offloading: Force software GSO for multiple vlan tags.")
Reported-and-tested-by: syzbot+0bbe42c764feafa82c5a@syzkaller.appspotmail.com
Signed-off-by: Toshiaki Makita <makita.toshiaki@lab.ntt.co.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>

MIPS: memset.S: Fix return of __clear_user from Lpartial_fixup

The __clear_user function is defined to return the number of bytes that
could not be cleared. From the underlying memset / bzero implementation
this means setting register a2 to that number on return. Currently if a
page fault is triggered within the memset_partial block, the value
loaded into a2 on return is meaningless.

The label .Lpartial_fixup\@ is jumped to on page fault. In order to work
out how many bytes failed to copy, the exception handler should find how
many bytes left in the partial block (andi a2, STORMASK), add that to
the partial block end address (a2), and subtract the faulting address to
get the remainder. Currently it incorrectly subtracts the partial block
start address (t1), which has additionally been clobbered to generate a
jump target in memset_partial. Fix this by adding the block end address
instead.

This issue was found with the following test code:
      int j, k;
      for (j = 0; j < 512; j++) {
        if ((k = clear_user(NULL, j)) != j) {
           pr_err("clear_user (NULL %d) returned %d\n", j, k);
        }
      }
Which now passes on Creator Ci40 (MIPS32) and Cavium Octeon II (MIPS64).

Suggested-by: James Hogan <jhogan@kernel.org>
Signed-off-by: Matt Redfearn <matt.redfearn@mips.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-mips@linux-mips.org
Cc: stable@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/19108/
Signed-off-by: James Hogan <jhogan@kernel.org>

net: qrtr: add MODULE_ALIAS_NETPROTO macro

To ensure that qrtr can be loaded automatically, when needed, if it is compiled
as module.

Signed-off-by: Nicolas Dechesne <nicolas.dechesne@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

VSOCK: make af_vsock.ko removable again

Commit c1eef220c1760762753b602c382127bfccee226d ("vsock: always call
vsock_init_tables()") introduced a module_init() function without a
corresponding module_exit() function.

Modules with an init function can only be removed if they also have an
exit function.  Therefore the vsock module was considered "permanent"
and could not be removed.

This patch adds an empty module_exit() function so that "rmmod vsock"
works.  No explicit cleanup is required because:

1. Transports call vsock_core_exit() upon exit and cannot be removed
   while sockets are still alive.
2. vsock_diag.ko does not perform any action that requires cleanup by
   vsock.ko.

Fixes: c1eef220c176 ("vsock: always call vsock_init_tables()")
Reported-by: Xiumei Mu <xmu@redhat.com>
Cc: Cong Wang <xiyou.wangcong@gmail.com>
Cc: Jorgen Hansen <jhansen@vmware.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Jorgen Hansen <jhansen@vmware.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

xen: xenbus_dev_frontend: Really return response string

xenbus_command_reply() did not actually copy the response string and
leaked stack content instead.

Fixes: 9a6161fe73bd ("xen: return xenstore command failures via response instead of rc")
Signed-off-by: Simon Gaiser <simon@invisiblethingslab.com>
Reviewed-by: Juergen Gross <jgross@suse.com>
Signed-off-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>

xen/sndif: Sync up with the canonical definition in Xen

This is the sync up with the canonical definition of the sound
protocol in Xen:

1. Protocol version was referenced in the protocol description,
   but missed its definition. Fixed by adding a constant
   for current protocol version.

2. Some of the request descriptions have "reserved" fields
   missed: fixed by adding corresponding entries.

3. Extend the size of the requests and responses to 64 octets.
   Bump protocol version to 2.

4. Add explicit back and front synchronization
   In order to provide explicit synchronization between backend and
   frontend the following changes are introduced in the protocol:
    - add new ring buffer for sending asynchronous events from
      backend to frontend to report number of bytes played by the
      frontend (XENSND_EVT_CUR_POS)
    - introduce trigger events for playback control: start/stop/pause/resume
    - add "req-" prefix to event-channel and ring-ref to unify naming
      of the Xen event channels for requests and events

5. Add explicit back and front parameter negotiation
   In order to provide explicit stream parameter negotiation between
   backend and frontend the following changes are introduced in the protocol:
   add XENSND_OP_HW_PARAM_QUERY request to read/update
   configuration space for the parameters given: request passes
   desired parameter's intervals/masks and the response to this request
   returns allowed min/max intervals/masks to be used.

Signed-off-by: Oleksandr Andrushchenko <oleksandr_andrushchenko@epam.com>
Signed-off-by: Oleksandr Grytsov <oleksandr_grytsov@epam.com>
Reviewed-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Reviewed-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>

livepatch: Allow to call a custom callback when freeing shadow variables

We might need to do some actions before the shadow variable is freed.
For example, we might need to remove it from a list or free some data
that it points to.

This is already possible now. The user can get the shadow variable
by klp_shadow_get(), do the necessary actions, and then call
klp_shadow_free().

This patch allows to do it a more elegant way. The user could implement
the needed actions in a callback that is passed to klp_shadow_free()
as a parameter. The callback usually does reverse operations to
the constructor callback that can be called by klp_shadow_*alloc().

It is especially useful for klp_shadow_free_all(). There we need to do
these extra actions for each found shadow variable with the given ID.

Note that the memory used by the shadow variable itself is still released
later by rcu callback. It is needed to protect internal structures that
keep all shadow variables. But the destructor is called immediately.
The shadow variable must not be access anyway after klp_shadow_free()
is called. The user is responsible to protect this any suitable way.

Be aware that the destructor is called under klp_shadow_lock. It is
the same as for the contructor in klp_shadow_alloc().

Signed-off-by: Petr Mladek <pmladek@suse.com>
Acked-by: Josh Poimboeuf <jpoimboe@redhat.com>
Acked-by: Miroslav Benes <mbenes@suse.cz>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>

livepatch: Initialize shadow variables safely by a custom callback

The existing API allows to pass a sample data to initialize the shadow
data. It works well when the data are position independent. But it fails
miserably when we need to set a pointer to the shadow structure itself.

Unfortunately, we might need to initialize the pointer surprisingly
often because of struct list_head. It is even worse because the list
might be hidden in other common structures, for example, struct mutex,
struct wait_queue_head.

For example, this was needed to fix races in ALSA sequencer. It required
to add mutex into struct snd_seq_client. See commit b3defb791b26ea06
("ALSA: seq: Make ioctls race-free") and commit d15d662e89fc667b9
("ALSA: seq: Fix racy pool initializations")

This patch makes the API more safe. A custom constructor function and data
are passed to klp_shadow_*alloc() functions instead of the sample data.

Note that ctor_data are no longer a template for shadow->data. It might
point to any data that might be necessary when the constructor is called.

Also note that the constructor is called under klp_shadow_lock. It is
an internal spin_lock that synchronizes alloc() vs. get() operations,
see klp_shadow_get_or_alloc(). On one hand, this adds a risk of ABBA
deadlocks. On the other hand, it allows to do some operations safely.
For example, we could add the new structure into an existing list.
This must be done only once when the structure is allocated.

Reported-by: Nicolai Stange <nstange@suse.de>
Signed-off-by: Petr Mladek <pmladek@suse.com>
Acked-by: Josh Poimboeuf <jpoimboe@redhat.com>
Acked-by: Miroslav Benes <mbenes@suse.cz>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>

powerpc/64s: Default l1d_size to 64K in RFI fallback flush

If there is no d-cache-size property in the device tree, l1d_size could
be zero. We don't actually expect that to happen, it's only been seen
on mambo (simulator) in some configurations.

A zero-size l1d_size leads to the loop in the asm wrapping around to
2^64-1, and then walking off the end of the fallback area and
eventually causing a page fault which is fatal.

Just default to 64K which is correct on some CPUs, and sane enough to
not cause a crash on others.

Fixes: aa8a5e0062ac9 ('powerpc/64s: Add support for RFI flush of L1-D cache')
Signed-off-by: Madhavan Srinivasan <maddy@linux.vnet.ibm.com>
[mpe: Rewrite comment and change log]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

netfilter: conntrack: include kmemleak.h for kmemleak_not_leak()

After merging the netfilter tree, today's linux-next build (powerpc
ppc64_defconfig) failed like this:

net/netfilter/nf_conntrack_extend.c: In function 'nf_ct_ext_add':
net/netfilter/nf_conntrack_extend.c:74:2: error: implicit declaration of function 'kmemleak_not_leak' [-Werror=implicit-function-declaration]
kmemleak_not_leak(old);
^~~~~~~~~~~~~~~~~
cc1: some warnings being treated as errors

Fixes: 114aa35d06d4 ("netfilter: conntrack: silent a memory leak warning")
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>

s390/signal: cleanup uapi struct sigaction

The struct sigaction for user space in arch/s390/include/uapi/asm/signal.h
is ill defined. The kernel uses two structures 'struct sigaction' and
'struct old_sigaction', the correlation in the kernel for both 31 and
64 bit is as follows

    sys_sigaction -> struct old_sigaction
    sys_rt_sigaction -> struct sigaction

The correlation of the (single) uapi definition for 'struct sigaction'
under '#ifndef __KERNEL__':

    31-bit: sys_sigaction -> uapi struct sigaction
    31-bit: sys_rt_sigaction -> no structure available

    64-bit: sys_sigaction -> no structure available
    64-bit: sys_rt_sigaction -> uapi struct sigaction

This is quite confusing. To make it a bit less confusing make the
uapi definition of 'struct sigaction' usable for sys_rt_sigaction for
both 31-bit and 64-bit.

Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>

textsearch: fix kernel-doc warnings and add kernel-api section

Make lib/textsearch.c usable as kernel-doc.
Add textsearch() function family to kernel-api documentation.
Fix kernel-doc warnings in <linux/textsearch.h>:
../include/linux/textsearch.h:65: warning: Incorrect use of kernel-doc format:
* get_next_block - fetch next block of data
../include/linux/textsearch.h:82: warning: Incorrect use of kernel-doc format:
* finish - finalize/clean a series of get_next_block() calls

Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: David S. Miller <davem@davemloft.net>