[media] drxk: Lock I2C bus during firmware load

Don't allow other devices at the same I2C bus to use it during
firmware load, in order to prevent using the device while it is
not on a sane state.

Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] drxk: pass drxk priv struct instead of I2C adapter to i2c calls

As it will be using the unlocked version of i2c_transfer during
firmware loads, make sure that the priv state routine will be
used on all I2C calls, in preparation for the next patch that
will implement an exclusive lock mode to be used during firmware
load, at drxk_init.

Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] drxk: change it to use request_firmware_nowait()

The firmware blob may not be available when the driver probes.

Instead of blocking the whole kernel use request_firmware_nowait() and
continue without firmware.

This shouldn't be that bad on drx-k devices, as they all seem to have an
internal firmware. So, only the firmware update will take a little longer
to happen.

Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] i2c: Export an unlocked flavor of i2c_transfer

Some drivers (in particular for TV cards) need exclusive access to
their I2C buses for specific operations. Export an unlocked flavor
of i2c_transfer to give them full control.

The unlocked flavor has the following limitations:
* Obviously, caller must hold the i2c adapter lock.
* No debug messages are logged. We don't want to log messages while
  holding a rt_mutex.
* No check is done on the existence of adap->algo->master_xfer. It
  is thus the caller's responsibility to ensure that the function is
  OK to call.

Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

Merge branch 'v4l_for_linus' into staging/for_v3.6

* v4l_for_linus: (44 commits)
  [media] smia: Fix compile failures
  [media]  Fix VIDIOC_DQEVENT docbook entry
  [media] s5p-fimc: Fix control creation function
  [media] s5p-mfc: Fix checkpatch error in s5p_mfc_shm.h file
  [media] s5p-mfc: Fix setting controls
  [media] v4l/s5p-mfc: added image size align in VIDIOC_TRY_FMT
  [media] v4l/s5p-mfc: corrected encoder v4l control definitions
  [media] v4l: mem2mem_testdev: Fix race conditions in driver
  [media] s5p-mfc: Bug fix of timestamp/timecode copy mechanism
  [media] cxd2820r: Fix an incorrect modulation type bitmask
  [media] em28xx: Show a warning if the board does not support remote controls
  [media] em28xx: Add remote control support for Terratec's Cinergy HTC Stick HD
  [media] USB: Staging: media: lirc: initialize spinlocks before usage
  [media] Revert "[media] media: mx2_camera: Fix mbus format handling"
  [media] bw-qcam: driver and pixfmt documentation fixes
  [media] cx88: fix firmware load on big-endian systems
  [media] cx18: support big-endian systems
  [media] ivtv: fix support for big-endian systems
  [media] tuner-core: return the frequency range of the correct tuner
  [media] v4l2-dev.c: fix g_parm regression in determine_valid_ioctls()
  ...

Conflicts:
Documentation/DocBook/media/v4l/vidioc-create-bufs.xml
drivers/media/video/em28xx/em28xx-cards.c

[media] media: gpio-ir-recv: switch to module_platform_driver

Cc: Ravi Kumar V <kumarrav@codeaurora.org>
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] media: gpio-ir-recv: add map name

Make it possible for gpio-ir-recv users to choose a map name.

Cc: Ravi Kumar V <kumarrav@codeaurora.org>
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] media: gpio-ir-recv: fix missing udev by-path entry

Add missing information so that udev can create an entry for gpio-ir-recv under
/dev/input/by-path/ .

Cc: Ravi Kumar V <kumarrav@codeaurora.org>
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] radio-sf16fmi: Use LM7000 driver

Convert radio-sf16fmi to use generic LM7000 driver.
Tested with SF16-FMI, SF16-FMP and SF16-FMD.

Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] radio-aimslab: Use LM7000 driver

Convert radio-aimslab to use generic LM7000 driver.
Tested with Reveal RA300.

Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] radio: Add Sanyo LM7000 tuner driver

Add very simple driver for Sanyo LM7000 AM/FM tuner chip. Only FM is supported
as there is no known HW with AM implemented.

This will be used by radio-aimslab and radio-sf16fmi.

Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

Revert "[media] radio: Add Sanyo LM7000 tuner driver"

This reverts commit 4ecbb69414c61af3594209e081d6e834ea68a16d.

As requested by Hans Verkuil:
> You accidentally merged the wrong first version of the lm7000 patch series.
>
> These are the correct second version patches:
>
> http://patchwork.linuxtv.org/patch/11689/
> http://patchwork.linuxtv.org/patch/11690/
> http://patchwork.linuxtv.org/patch/11691/
>
> The second version is much simpler and doesn't require the creation of a whole
> new driver.

Requested-by: Hans Verkuil <hverkuil@xs4all.nl>
Cc: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

Revert "[media] radio-aimslab: Use LM7000 driver"

This reverts commit bece083a6b2b242c7ab74117640396e1bd851e49.

As requested by Hans Verkuil:
> You accidentally merged the wrong first version of the lm7000 patch series.
>
> These are the correct second version patches:
>
> http://patchwork.linuxtv.org/patch/11689/
> http://patchwork.linuxtv.org/patch/11690/
> http://patchwork.linuxtv.org/patch/11691/
>
> The second version is much simpler and doesn't require the creation of a whole
> new driver.

Requested-by: Hans Verkuil <hverkuil@xs4all.nl>
Cc: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

Revert "[media] radio-sf16fmi: Use LM7000 driver"

This reverts commit 1e70a6cf7e965bafd89bf363772eb1a4b8e35934.

As requested by Hans Verkuil:
> You accidentally merged the wrong first version of the lm7000 patch series.
>
> These are the correct second version patches:
>
> http://patchwork.linuxtv.org/patch/11689/
> http://patchwork.linuxtv.org/patch/11690/
> http://patchwork.linuxtv.org/patch/11691/
>
> The second version is much simpler and doesn't require the creation of a whole
> new driver.

Requested-by: Hans Verkuil <hverkuil@xs4all.nl>
Cc: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] tvaudio: rename getmode and setmode

This is basically s/getmode/getrxsubchans/ and s/setmode/setaudmode/
with some whitespace adjustment in affected lines to please the eye.
The rename is done to point out their relation to the rxsubchans and
audmode fields of struct v4l2_tuner.

I also corrected a commented out call to v4l_dbg in one of the lines.

Signed-off-by: Daniel Glöckner <daniel-gl@gmx.net>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] s5h1420: Unused variable clock_setting

The switch/case was setting clock_setting that is not being used. Both switch/case and the variable definition were removed.

Currently clock is being calculated by the formula:
(state->fclk/1000000 - 8)

Tested by compilation only.

Signed-off-by: Peter Senna Tschudin <peter.senna@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] stv090x: variable 'no_signal' set but not used

Tested by compilation only.

Signed-off-by: Peter Senna Tschudin <peter.senna@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] stv0367: variable 'tps_rcvd' set but not used

Tested by compilation only.

Signed-off-by: Peter Senna Tschudin <peter.senna@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] saa7164: Variable set but not used

In function saa7164_api_i2c_read variable regval was set but not used.

Tested by compilation only.

Signed-off-by: Peter Senna Tschudin <peter.senna@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] pvrusb2: Variables set but not used

Tested by compilation only.

Signed-off-by: Peter Senna Tschudin <peter.senna@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] cx231xx: Paranoic stack memory save

Saves 255 bytes of stack memory on cx231xx_usb_probe() by removing a char array.

Tested by compilation only.

Signed-off-by: Peter Senna Tschudin <peter.senna@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] [trivial] v4l drivers: typo, change ctruct to struct in comment

Signed-off-by: Peter Meerwald <p.meerwald@bct-electronic.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] stradis: remove unused V4L1 headers

Commit 39c3d488452ae206cfc8afda0db041ee55d01c3c ("[media] cpia, stradis:
remove deprecated V4L1 drivers") removed the last file including these
five headers. Apparently it was just an oversight to keep them in the
tree. They can safely be removed now.

Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] em28xx: Improve support for the Terratec Cinergy HTC Stick HD

The windows driver used different values for the GPIOs and analog
decoder configuration. The values from the windows driver are now
used.
It also seems that the windows driver has LNA always disabled.
Thus we are doing the same (using the same flags as on windows).

I (only) tested with DVB-T and it worked quite well.

[mchehab@redhat.com: Fix merge conflicts and tested with DVB-C]
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Tested-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] em28xx: Add the DRX-K at I2C address 0x29 to the list of known I2C devices

Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] Add support for downloading the firmware of the Terratec Cinergy HTC Stick HD's firmware

As of June 2012 it uses the same firmware as the Hauppauge WinTV HVR 930C.

Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] radio-sf16fmi: Use LM7000 driver

Convert radio-sf16fmi to use generic LM7000 driver.
Tested with SF16-FMI, SF16-FMP and SF16-FMD.

radio.");
@@ -48,37 +50,40 @@ struct fmi
  bool mute;
  unsigned long curfreq; /* freq in kHz */
  struct mutex lock;
+ struct lm7000 lm;
 };

 static struct fmi fmi_card;
 static struct pnp_dev *dev;
 bool pnp_attached;

-/* freq is in 1/16 kHz to internal number, hw precision is 50 kHz */
-/* It is only useful to give freq in interval of 800 (=0.05Mhz),
- * other bits will be truncated, e.g 92.7400016 -> 92.7, but
- * 92.7400017 -> 92.75
- */
-#define RSF16_ENCODE(x) ((x) / 800 + 214)
 #define RSF16_MINFREQ (87 * 16000)
 #define RSF16_MAXFREQ (108 * 16000)

-static void outbits(int bits, unsigned int data, int io)
+#define FMI_BIT_TUN_CE (1 << 0)
+#define FMI_BIT_TUN_CLK (1 << 1)
+#define FMI_BIT_TUN_DATA (1 << 2)
+#define FMI_BIT_VOL_SW (1 << 3)
+#define FMI_BIT_TUN_STRQ (1 << 4)
+
+void fmi_set_pins(struct lm7000 *lm, u8 pins)
 {
- while (bits--) {
- if (data & 1) {
- outb(5, io);
- udelay(6);
- outb(7, io);
- udelay(6);
- } else {
- outb(1, io);
- udelay(6);
- outb(3, io);
- udelay(6);
- }
- data >>= 1;
- }

Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] radio-aimslab: Use LM7000 driver

Convert radio-aimslab to use generic LM7000 driver.
Tested with Reveal RA300.

Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] radio: Add Sanyo LM7000 tuner driver

Add very simple driver for Sanyo LM7000 AM/FM tuner chip. Only FM is supported
as there is no known HW with AM implemented.

This will be used by radio-aimslab and radio-sf16fmi.

Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] em28xx: Make a few drxk_config structs static

Signed-off-by: Ezequiel Garcia <elezegarcia@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] em28xx: Remove unused AC97 register definitions

There is a specific header sound/ac97_codec.h that defines these.
All drivers should use it instead of rolling its own set of macros.

Signed-off-by: Ezequiel Garcia <elezegarcia@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] em28xx: Rename AC97 registers to use sound/ac97_codec.h definitions

Signed-off-by: Ezequiel Garcia <elezegarcia@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] em28xx: Fix wrong AC97 mic register usage

Signed-off-by: Ezequiel Garcia <elezegarcia@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] zr364xx: add suspend/resume support

And fix initial control setup.

Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] zr364xx: allow multiple opens

This driver allowed only one open filehandle. This is against the spec, so
fix the driver by assigning proper ownership when streaming.

Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] zr364xx: add support for control events

Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] zr364xx: fix querycap and fill in colorspace

Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] zr364xx: convert to the control framework

Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] zr364xx: introduce v4l2_device

Implement struct v4l2_device: use the core lock and use the v4l2_device
release() callback.

Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] zr364xx: embed video_device and register it at the end of probe

Embed the video_device struct instead of allocating it and register it as
the last thing in probe().

Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] V4L2 Spec: fix typo: NTSC -> NRSC

Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] V4L2 spec: clarify a few modulator issues

Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] S_HW_FREQ_SEEK: set capability flags and return ENODATA instead of EAGAIN

Set the new capability flags in G_TUNER and return ENODATA if no channels
were found.

Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] v4l2 spec: document the new v4l2_tuner capabilities

Update the spec with the new capabilities and specify new error codes for
S_HW_FREQ_SEEK.

Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] videodev2.h: add new hwseek capability bits

Tell the application whether the hardware seek is bounded and/or wraps around.

Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] tvaudio: don't report mono when stereo is received

The V4L2 spec says reporting mono and stereo at the same time means
the hardware can not distinguish between the two. So when we can,
we should report only one of them.

Signed-off-by: Daniel Glöckner <daniel-gl@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] tvaudio: support V4L2_TUNER_MODE_LANG1_LANG2

Many of the audio decoders handled by the driver support this mode,
so the driver should support it as well.

Coding style errors are done to blend into the surrounding code.

Signed-off-by: Daniel Glöckner <daniel-gl@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] tvaudio: obey V4L2 tuner audio matrix

V4L2 specifies the audio mode to use for combinations of possible
(rxsubchans) and requested (audmode) audio modes. Up to now tvaudio
has made these decisions automatically based on the possible audio
modes from setting of the frequency until VIDIOC_S_TUNER was called.
It then forced the hardware to use the mode requested by the user.
With this patch it continues to adjust the audio mode while taking
the requested mode into account.

Signed-off-by: Daniel Glöckner <daniel-gl@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] tvaudio: use V4L2_TUNER_SUB_* for bitfields

The V4L2_TUNER_MODE_* constants are not suited for use in bitfields.

Signed-off-by: Daniel Glöckner <daniel-gl@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] tvaudio: don't use thread for TA8874Z

Judging from the data sheet it will automatically switch to the next
best audio mode in accordance with the V4L2 tuner audio matrix.

Signed-off-by: Daniel Glöckner <daniel-gl@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] tvaudio: remove watch_stereo

It is never read and only assigned 0.

Signed-off-by: Daniel Glöckner <daniel-gl@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] tvaudio: use V4L2_TUNER_MODE_SAP for TDA985x SAP

As V4L2_TUNER_MODE_SAP == V4L2_TUNER_MODE_LANG2, we make
V4L2_TUNER_MODE_LANG1 equal to V4L2_TUNER_MODE_STEREO.

Signed-off-by: Daniel Glöckner <daniel-gl@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] tvaudio: fix tda8425_setmode

The passed audio mode is not a bitfield.

Signed-off-by: Daniel Glöckner <daniel-gl@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] tvaudio: fix TDA9873 constants

These constants were unused so far but need | instead of &.

Signed-off-by: Daniel Glöckner <daniel-gl@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] saa7146: Variable set but not used

In function fops_open variable type was set but not used. Tested by compilation only.

Signed-off-by: Peter Senna Tschudin <peter.senna@gmail.com>
Acked-by: Michael Hunold <michael@mihu.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] em28xx: Make em28xx_ir_change_protocol a static function

Signed-off-by: Ezequiel Garcia <elezegarcia@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] staging: solo6x10: fix | vs &

The test here is never true because '&' was used instead of '|'.  It was
the same as:

if (status & ((1<<16) & (1<<17)) ...

Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] videobuf2: correct the #ifndef text mistake in videobuf2-dma-contig.h

It should be a mistake due to copy & paste in header file
  Correct it in videobuf2-dma-config.h for avoiding duplicate include it

Change-Id: I1f71fcec2889c033c7db380c58d9a1369c5afb35

Signed-off-by: Albert Wang <twang13@marvell.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] smia: Fix compile failures

Fix compile of smia code.

Resolves-bug: https://bugzilla.kernel.org/show_bug.cgi?id=43337

Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Sakari Ailus <sakari.ailus@maxwell.research.nokia.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media]  Fix VIDIOC_DQEVENT docbook entry

Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Sakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] s5p-fimc: Fix control creation function

Fixed the size of the V4L2_CID_COLORFX control cluster.
Prior to this fix V4L2_CID_ROTATE was also icluded in
the cluster preventing application from enabling rotation.

Reported-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] s5p-mfc: Fix checkpatch error in s5p_mfc_shm.h file

Fixes the following error:
ERROR: open brace '{' following enum go on the same line
+enum MFC_SHM_OFS
+{

Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Acked-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] s5p-mfc: Fix setting controls

Fixed s_ctrl function when setting the following controls:
- V4L2_CID_MPEG_VIDEO_DECODER_MPEG4_DEBLOCK_FILTER
- V4L2_CID_MPEG_MFC51_VIDEO_DECODER_H264_DISPLAY_DELAY

Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] v4l/s5p-mfc: added image size align in VIDIOC_TRY_FMT

Image size for MFC encoder should have size between
8x4 and 1920x1080 with even width and height.

Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] v4l/s5p-mfc: corrected encoder v4l control definitions

Patch corrects definition of H264 level control and
changes bare numbers to enums in two other cases.

Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] v4l: mem2mem_testdev: Fix race conditions in driver

The mem2mem_testdev allows multiple instances to be opened in parallel.
Source and destination queue data are being shared between all
instances, which can lead to kernel oops due to race conditions (most
likely to happen inside device_run()).

Attached patch fixes mentioned problem by storing queue data per device
context.

Signed-off-by: Tomasz Moń <desowin@gmail.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] s5p-mfc: Bug fix of timestamp/timecode copy mechanism

Fixed the code copying timecode/timestamp to corresponding
frames between OUTPUT and CAPTURE.

Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] lirc_sir: make device registration work

For one, the driver device pointer needs to be filled in, or the lirc core
will refuse to load the driver. And we really need to wire up all the
platform_device bits. This has been tested via the lirc sourceforge tree
and verified to work, been sitting there for months, finally getting
around to sending it. :\

CC: Josh Boyer <jwboyer@redhat.com>
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] DVB: stb0899: speed up getting BER values

stb0899_read_ber() takes 500ms (half a second!) to deliver the current
BER value. Apparently it takes 5 subsequent readings, with a 100ms pause
between them (and even before the first one). This is a real performance
brake if an application freqeuently reads the BER of several devices.
The attached patch reduces this to a single reading, with no more pausing.
I didn't observe any negative side effects of this change.

Signed-off-by: Klaus Schmidinger <Klaus.Schmidinger@tvdr.de>
Cc: Manu Abraham <abraham.manu@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] media: video: bt8xx: Remove duplicated pixel format entry

Signed-off-by: Volokh Konstantin <volokh84@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] cxd2820r: Fix an incorrect modulation type bitmask

Fix an incorrect modulation type bitmask. This allows QAM256 also to be
correctly reported.

Signed-off-by: Janne Huttunen <jahuttun@gmail.com>
Acked-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] em28xx: Show a warning if the board does not support remote controls

This simply shows a little warning if the board does not have remote
control support. This should make it easier for users to see if they
have misconfigured their system or if the driver simply does not have
rc-support for their card (yet).

Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] em28xx: Add remote control support for Terratec's Cinergy HTC Stick HD

The Cinergy HTC Stick HD uses the same remote control as the TerraTec
Cinergy XS products. Thus the same keymap could be re-used.

Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] USB: Staging: media: lirc: initialize spinlocks before usage

Initialize the spinlock for each hardware time.

Signed-off-by: Sasha Levin <levinsasha928@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] s5p-fimc: Add missing static storage class specifiers

Fixes the following sparse warnings:

drivers/media/video/s5p-fimc/fimc-lite-reg.c:218:6: warning: symbol
'flite_hw_set_out_order' was not declared. Should it be static?

drivers/media/video/s5p-fimc/fimc-mdevice.c:183:5: warning: symbol '__fimc_pipeline_shutdown' was not declared. Should it be static?
drivers/media/video/s5p-fimc/fimc-mdevice.c:1013:12: warning: symbol 'fimc_md_init' was not declared. Should it be static?
drivers/media/video/s5p-fimc/fimc-mdevice.c:1024:13: warning: symbol 'fimc_md_exit' was not declared. Should it be static?

drivers/media/video/s5p-fimc/fimc-core.c:466:5: warning: symbol 'fimc_set_color_effect' was not declared. Should it be static?

drivers/media/video/s5p-fimc/fimc-capture.c:1163:5: warning: symbol 'enclosed_rectangle' was not declared. Should it be static?

Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Acked-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] videobuf-dma-contig: use gfp_t for GFP flags

Sparse complains if about using unsigned long.
videobuf-dma-contig.c:47:67: warning: restricted gfp_t degrades to integer
videobuf-dma-contig.c:47:65: warning: incorrect type in argument 2 (different base types)
videobuf-dma-contig.c:47:65:    expected restricted gfp_t [usertype] gfp_mask
videobuf-dma-contig.c:47:65:    got unsigned long

Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] gspca: Maintainer change

Hans de Goede accepted to be the new gspca maintainer.

Signed-off-by: Jean-François Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] Revert "[media] media: mx2_camera: Fix mbus format handling"

This reverts commit d509835e32bd761a2b7b446034a273da568e5573. That commit
breaks support for the generic pass-through mode in the driver for formats,
not natively supported by it. Besides due to a merge conflict it also breaks
driver compilation:

drivers/media/video/mx2_camera.c: In function 'mx2_camera_set_bus_param':
drivers/media/video/mx2_camera.c:937: error: 'pixfmt' undeclared (first use in this function)
drivers/media/video/mx2_camera.c:937: error: (Each undeclared identifier is reported only once
drivers/media/video/mx2_camera.c:937: error: for each function it appears in.)

Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Cc: Javier Martin <javier.martin@vista-silicon.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] v4l: Correct create_bufs documentation

Patch id 6016af82eafcb6e086a8f2a2197b46029a843d68 ("[media] v4l2: use __u32
rather than enums in ioctl() structs") unintentionally changes the type of
the format field in struct v4l2_create_buffers from struct v4l2_format to
__u32. Revert that change.

Signed-off-by: Sakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] bw-qcam: driver and pixfmt documentation fixes

Fix the documentation of the Y4 and Y6 formats.
Fix a poll() issue, add support for enum_frmsizes, set the proper
parent device and fix a few compliance issues.

Tested with an actual Connectix B&W parallel port webcam, both on a
little-endian and a big-endian platform. This driver has never been
so good, doing 320x240 at 1 frame per second :-)

I know, nobody cares, but still it is cool that linux can still support
this old webcam.

Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] cx88: fix firmware load on big-endian systems

Tested with a HVR-1300.

Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] cx18: support big-endian systems

base_addr has type resource_size_t, which may be 64 bits.

Also fix a few endian issues related to mailboxes and firmware loading.

Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] ivtv: fix support for big-endian systems

base_addr has type resource_size_t, which may be 64 bits on a 32-bit ppc.

Tested on my ppc board.

Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] tuner-core: return the frequency range of the correct tuner

The frequency range of the current tuner (radio or TV) was returned
instead of the frequency range of the requested tuner (which depends
on the device node).

This bug caused the frequency range of the radio tuner to be returned
when G_TUNER was called on a video node.

Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] v4l2-dev.c: fix g_parm regression in determine_valid_ioctls()

The field current_norm does not have to be set for g_parm to be a valid
ioctl. Remove that check, but add a check whether this is a video node
instead as g_parm only makes sense for those nodes.

Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] v4l2-ioctl: set readbuffers to 2 in g_parm

If g_parm is handled automatically, then set readbuffers to 2, which is the
minimum number of buffers videobuf uses.

Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] smsusb: add autodetection support for USB ID 2040:f5a0

Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Cc: stable@kernel.org
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] vino: fix compiler warnings

v4l-dvb-git/drivers/media/video/vino.c: In function 'vino_acquire_input':
v4l-dvb-git/drivers/media/video/vino.c:2602:18: warning: 'data_norm' may be used uninitialized in this function [-Wuninitialized]
v4l-dvb-git/drivers/media/video/vino.c: In function 'vino_set_input':
v4l-dvb-git/drivers/media/video/vino.c:2690:19: warning: 'data_norm' may be used uninitialized in this function [-Wuninitialized]

Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] cx24110: fix compiler warning

v4l-dvb-git/drivers/media/dvb/frontends/cx24110.c: In function â€˜cx24110_read_ucblocks’:
v4l-dvb-git/drivers/media/dvb/frontends/cx24110.c:520:40: warning: value computed is not used [-Wunused-value]

Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] saa7146_fops: remove unused variable

Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] gspca - sonixj: Fix bad values of webcam 0458:7025

The webcam 0458:7025 (Eye911Q) has:
- an inverted power pin,
- a sensor mi0360b which cannot be probed.

Signed-off-by: Jean-François Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] gspca - ov534/ov534_9: Fix sccd_read/write errors

The ov534 bridge is too slow to handle the sensor accesses
requested by fast hosts giving 'sccb_reg_write failed'.
A small delay fixes the problem.

Signed-off-by: Jean-François Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] gspca-core: Fix buffers staying in queued state after a stream_off

This fixes a regression introduced by commit f7059ea and should be
backported to all supported stable kernels which have this commit.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Tested-by: Antonio Ospite <ospite@studenti.unina.it>
CC: stable@vger.kernel.org
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] gspca_ov534: make AGC and AWB controls independent

Even if the best results are indeed achieved with both AGC and AWB
enabled, the webcam is capable of setting these independently, and the
user can see the difference of any of the 4 combinations of these two
boolean controls.

Removing the dependency from one another simplifies the code and gives
more control to the user.

Signed-off-by: Antonio Ospite <ospite@studenti.unina.it>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] gscpa_sn9c20x: Move clustering of controls to after error checking

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] gspca_pac7311: Correct number of controls

This avoids the need for a re-alloc during init.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] bttv: The Hauppauge 61334 needs the msp3410 to do radio demodulation

The (radio) audio out from the tuner (which can also demod FM radio) does not
seem to be hooked up to the msp3410 on this board in any way, so the only way
to get sound from the radio part is to make the msp3410 do the FM radio demod.

The msp3410 can handle this fine, but it is a bit weird compared to how it
is handled on other boards.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] bttv: Remove unused needs_tvaudio card variable

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] bttv: Use btv->has_radio rather then the card info when registering the tuner

bttv_init_card2() sets btv->has_audio to a *default* value from the tvcards
array and then may update it by reading a card specific eeprom or gpio
detection.

After bttv_init_card2(), bttv_init_tuner() gets called, and it should clearly
use the updated, dynamic has_radio value from btv->has_radio, rather then
the const value in the tvcards array.

This fixes the radio not working on my Hauppauge WinTV.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] snd_tea575x: set_freq: update cached freq to the actual achieved frequency

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
CC: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>