Felix Fietkau [Sat, 23 Mar 2019 08:59:35 +0000 (09:59 +0100)]
mac80211: improve performance by deferring tx queue selection
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Felix Fietkau [Sat, 23 Mar 2019 13:29:00 +0000 (14:29 +0100)]
ramips: implement vlan rx offload on MT7621
Avoids the overhead of software VLAN untagging in the network stack
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Magnus Kroken [Tue, 2 Apr 2019 20:18:44 +0000 (22:18 +0200)]
openvpn: openssl: explicitly depend on deprecated APIs
OpenVPN as of 2.4.7 uses some OpenSSL APIs that are deprecated in
OpenSSL >= 1.1.0.
Signed-off-by: Magnus Kroken <mkroken@gmail.com>
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com> [white space fix]
Adrian Schmutzler [Mon, 25 Mar 2019 17:46:26 +0000 (18:46 +0100)]
ath79: Add support for TP-Link CPE210 v2
This PR adds support for a popular low-cost 2.4GHz N based AP
Specifications:
- SoC: Qualcomm Atheros QCA9533 (650MHz)
- RAM: 64MB
- Storage: 8 MB SPI NOR
- Wireless: 2.4GHz N based built into SoC 2x2
- Ethernet: 1x 100/10 Mbps, integrated into SoC, 24V POE IN
Installation:
Flash factory image through stock firmware WEB UI
or through TFTP
To get to TFTP recovery just hold reset button while powering on
for around 4-5 seconds and release.
Rename factory image to recovery.bin
Stock TFTP server IP:192.168.0.100
Stock device TFTP adress:192.168.0.254
This is based on the support patch for the identical CPE210 v3
by Mario Schroen <m.schroen@web.de>.
Tested-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
[renamed dtsi filename]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Mario Schroen [Sun, 31 Mar 2019 19:07:03 +0000 (21:07 +0200)]
ath79: Add support for TP-Link CPE210 v3
Specifications:
* SoC: Qualcomm Atheros QCA9533 (650MHz)
* RAM: 64MB
* Storage: 8 MB SPI NOR
* Wireless: 2.4GHz N based built into SoC 2x2
* Ethernet: 1x 100/10 Mbps, integrated into SoC, 24V POE IN
Installation:
Flash factory image through stock firmware WEB UI or TFTP
To get to TFTP recovery just hold reset button while powering
on for around 4-5 seconds and release.
Rename factory image to recovery.bin
Stock TFTP server IP:192.168.0.100
Stock device TFTP adress:192.168.0.254
Thanks to robimarko for the work inside the ar71xx tree.
Thanks to adrianschmutzler for deep discussion and fixes.
Signed-off-by: Mario Schroen <m.schroen@web.de>
[Split into DTS/DTSI, read-only config partition in DTSI]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
[renamed dtsi filename, light subject touches]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Robert Marko [Sat, 11 Aug 2018 15:32:48 +0000 (17:32 +0200)]
ar71xx: Add support for TP-Link CPE210 v3
Looks identical to the v2.
This PR adds support for a popular low-cost 2.4GHz N based AP
Specifications:
- SoC: Qualcomm Atheros QCA9533 (650MHz)
- RAM: 64MB
- Storage: 8 MB SPI NOR
- Wireless: 2.4GHz N based built into SoC 2x2
- Ethernet: 1x 100/10 Mbps, integrated into SoC, 24V POE IN
Installation:
Flash factory image through stock firmware WEB UI
or through TFTP
To get to TFTP recovery just hold reset button while powering on for
around 4-5 seconds and release.
Rename factory image to recovery.bin
Stock TFTP server IP:192.168.0.100
Stock device TFTP adress:192.168.0.254
Tested-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Signed-off-by: Robert Marko <robimarko@gmail.com>
[Rebased, adjusted for separate tplink-safeloader entry, dynamic partitioning]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Adrian Schmutzler [Tue, 26 Mar 2019 10:41:57 +0000 (11:41 +0100)]
ar71xx: Use dynamic partitions for TP-Link CPE210 v2
This is also helpful to add support in ath79.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Tested-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Hans Dedecker [Mon, 1 Apr 2019 21:08:58 +0000 (23:08 +0200)]
netifd: update to latest git HEAD
361b3e4 proto-shell: return error in case setup fails
a97297d interface: set interface in TEARDOWN state when checking link state
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
Petr Štetiar [Mon, 1 Apr 2019 11:53:31 +0000 (13:53 +0200)]
build: image: Fix off-by-one in DTC kernel version checks
It was reported to me on IRC today, that my change causes issues with
kernel versions between 4.14 and 4.19.
It's because I've wrongly used `git describe` in order to get kernel
version where we should disable noisy DTC checks, but I should've used
`git tag --contains` instead.
Fixes: cbbef976e2b ("build: dtc: Disable noisy warnings by default")
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Petr Štetiar [Mon, 1 Apr 2019 10:03:50 +0000 (12:03 +0200)]
ar71xx: ens202ext: Fix whitespace issues
I've missed leading whitespace issues in the original patch, so fixing
it in this commit. Thanks to pepe2k for letting me know.
Fixes: d260813d ("ar71xx: ens202ext: Fix VLAN switch")
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Magnus Kroken [Wed, 27 Mar 2019 19:07:58 +0000 (20:07 +0100)]
openvpn: update to 2.4.7
Signed-off-by: Magnus Kroken <mkroken@gmail.com>
Kabuli Chana [Sun, 3 Mar 2019 20:53:23 +0000 (13:53 -0700)]
mwlwifi: Fix pcie timeout issue
Increase MAX_WAIT_FW_COMPLETE_ITERATIONS to 10000 as before commit
e5e0700 to prevent timeout as reported here: #308 (Original OP issue is
probably not related though as his post preceeds commit
e5e0700).
compile/test target mvebu/mamba, rango
Signed-off-by: Kabuli Chana <newtownBuild@gmail.com>
[commit subject and message tweaks]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
David Bauer [Fri, 29 Mar 2019 15:16:18 +0000 (16:16 +0100)]
ramips: add missing SPDX identifier for EX6150
This adds the SPDX license identifier for the NETGEAR EX6150. It was
missed when submitting the original patch.
Signed-off-by: David Bauer <mail@david-bauer.net>
Michael Pratt [Fri, 22 Feb 2019 05:28:50 +0000 (00:28 -0500)]
ar71xx: ens202ext: Fix VLAN switch
The target ENS202EXT was just recently added right before the stable
release of Openwrt 18.
It flashes fine, but the physical switch is almost impossible to use
until you have a VLAN set up. Tested on two devices.
The actual problem is that eth0 represents nothing for whatever reason.
In other words, both WAN and LAN are running from eth1. There may be an
underlying problem in the build, but for now, I assume that this is
correct and that a VLAN switch is an appropriate fix.
Also, it's virtually impossible to get the switch running right through
LuCI. It is one thing to get a switch to appear, but attempting to
configure it breaks the whole thing. The VLAN has to be set up
perfectly, otherwise, interfaces will not start up, and one is forced to
reset settings, OR, the new LuCI feature kicks in and reverses any
steps. It is extremely difficult to determine which virtual ports
correspond to which physical ethernet ports without being able to set up
the switch in LuCI.
Temporary Workaround: followed directions here
[openwrt/luci#867](https://github.com/openwrt/luci/issues/867)
Reviewed-by: Marty Plummer <hanetzer@startmail.com>
Signed-off-by: Michael Pratt <mpratt51@gmail.com>
[commit author fix, subject fix, message text wrap]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Christian Lamparter [Sat, 30 Mar 2019 09:33:47 +0000 (10:33 +0100)]
ath10k-firmware: update Candela Tech firmware images
Release notes since last time:
Release notes for wave-1 / 10.1:
2019-03-28: Fix sometimes using bad TID for management frames
in htt-mgt mode. (Backported from wave2, looks
like bug would be the same though.)
Release notes for wave-2 / 10.4:
2019-03-28: Fix off-channel scanning while associated in
proxy-station mode.
2019-03-29: Fix sometimes sending mgt frames on wrong tid when
using htt-mgt. This bug has been around since I first
enabled htt-mgt mode.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Hans Dedecker [Fri, 29 Mar 2019 14:45:28 +0000 (15:45 +0100)]
odhcpd: update to latest git HEAD
7798d50 netlink: rework IPv4 address refresh logic
0b20876 netlink: rework IPv6 address refresh logic
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
Koen Vandeputte [Thu, 28 Mar 2019 11:59:20 +0000 (12:59 +0100)]
kernel: bump 4.14 to 4.14.109
Refreshed all patches.
Compile-tested on: ar71xx, cns3xxx, imx6, x86_64
Runtime-tested on: ar71xx, cns3xxx, imx6, x86_64
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Koen Vandeputte [Thu, 28 Mar 2019 11:57:03 +0000 (12:57 +0100)]
kernel: bump 4.9 to 4.9.166
Refreshed all patches.
Compile-tested on: ar7
Runtime-tested on: none
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Rosen Penev [Thu, 14 Feb 2019 21:15:29 +0000 (13:15 -0800)]
ramips: Increase GB-PC1 SPI frequency to 80MHz
The specific flash chip used (W25Q256FVEM) accepts 50MHz for read
requests and higher for others. 104MHz for fast reads. ramips seems to
be limited to 80MHz based on testing with higher values (no speedup).
Based on upstream commit:
97738374a310b9116f9c33832737e517226d3722
time dd if=/dev/mtdblock3 of=/dev/null bs=64k from 42.96s to 7.01s
[test done with backported upstream v4.19 driver[1], for numbers on
stock 4.14 driver please take a look at `ramips: Increase GB-PC2 SPI
frequency to 80MHz` commit message]
1. https://github.com/openwrt/openwrt/pull/1578
Signed-off-by: Rosen Penev <rosenp@gmail.com>
[expanded note about spi driver version]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Rosen Penev [Fri, 29 Mar 2019 06:01:30 +0000 (23:01 -0700)]
ramips: Increase GB-PC2 SPI frequency to 80MHz
The flash chip on the board (Spansion S25FL256SAIF00) is rated to
support at least 50MHz for normal read requests according to the
datasheet. 133MHz for fast reads. However, ramips seems to be limited to
80MHz.
>From testing this, higher values do not improve speeds.
time dd if=/dev/mtdblock3 of=/dev/null bs=64k from
42.82s to 14.09s.
boot speed is also faster:
[ 66.884087] procd: - init - vs
[ 48.976049] procd: - init -
Since spi speed was requested:
[ 3.538884] spi-mt7621
1e000b00.spi: sys_freq:
225000000
CPU is 900MHz:
[ 0.000000] CPU Clock: 900MHz
Signed-off-by: Rosen Penev <rosenp@gmail.com>
[fixed commit message by adding missing 0 in the spi-mt7621 clock output]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
David Bauer [Thu, 21 Mar 2019 14:55:09 +0000 (15:55 +0100)]
ramips: add Netgear EX6150
SoC: MediaTek MT7621
RAM: 64M (Winbond W9751G6KB-25)
FLASH: 16MB (Macronix MX25L12835F)
WiFi: MediaTek MT7662E bgn 2SS
WiFi: MediaTek MT7662E nac 2SS
BTN: ON/OFF - Reset - WPS - AP/Extender toggle
LED: - Arrow Right (blue)
- Arrow Left (blue)
- WiFi 1 (red/green)
- WiFi 2 (red/green)
- Power (green/amber)
- WPS (Green)
UART: UART is present as Pads on the backside of the PCB. They are
located on the other side of the Ethernet port.
3.3V - GND - TX - RX / 57600-8N1
3.3V is the nearest one to the antenna connectors
Installation
------------
Update the factory image via the Netgear web-interfaces (by default:
192.168.1.250/24).
You can also use the factory image with the nmrpflash tool.
For more information see https://github.com/jclehner/nmrpflash
Signed-off-by: David Bauer <mail@david-bauer.net>
[merge conflict in 02_network, flash@0 node rename, wlan DTS triggers]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Vladimir Kot [Sat, 12 Jan 2019 09:43:28 +0000 (18:43 +0900)]
ramips: add support for ZyXEL Keenetic Start
Device specification:
- SoC: RT5350F
- CPU Frequency: 360 MHz
- Flash Chip: Winbond 25Q32 (4096 KiB)
- RAM: 32768 KiB
- 5x 10/100 Mbps Ethernet (4x LAN, 1x WAN)
- 1x external, non-detachable antenna
- UART (J1) header on PCB (57800 8n1)
- Wireless: SoC-intergated: 2.4GHz 802.11bgn
- USB: None
- 3x LED, 2x button
Flash instruction:
1. Configure PC with static IP 192.168.1.2/24 and start TFTP server.
2. Rename "openwrt-ramips-rt305x-kn_st-squashfs-sysupgrade.bin"
to "kstart_recovery.bin" and place it in TFTP server directory.
3. Connect PC with one of LAN ports, press the reset button, power up
the router and keep button pressed until power LED start blinking.
4. Router will download file from TFTP server, write it to flash and reboot.
Signed-off-by: Vladimir Kot <vova28rus@gmail.com>
[fixed git commit author and whitespace issues in DTS]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Tobias Welz [Fri, 11 Jan 2019 23:37:43 +0000 (00:37 +0100)]
ramips: add support for WIZnet WizFi630S board
The WIZnet WizFi630S board is in the miniPCIe form factor.
SoC: Mediatek MT7688AN
RAM: 128MB
Flash: 32Mb
WiFi: 2.4GHz
Ethernet: 3x 100Mbit
USB: 1 (USB 2.0)
serial ports: 2 (1x full, 1xlite)
Flash and recovery instructions: Use the factory installed u-boot boot
loader. It is available on UART2 (115200,8,n,1). Then get the
sysupgrade image from a tftp server.
Signed-off-by: Tobias Welz <tw@wiznet.eu>
[whitespace and device name in makefile fixes]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Daniel Golle [Thu, 28 Mar 2019 14:09:38 +0000 (15:09 +0100)]
iwinfo: Fix 802.11ad channel to frequency
c2cfe9d iwinfo: Fix 802.11ad channel to frequency
Fixes
9725aa271a ("iwinfo: update to latest git HEAD")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Petr Štetiar [Thu, 28 Mar 2019 11:57:08 +0000 (12:57 +0100)]
fstools: update to the latest master branch
ff1ded6 libfstools: Fix overflow of F2FS_MINSIZE constant
bc2c876 libfstools: Print error in case of loop blkdev failure
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Alexander Couzens [Sat, 16 Mar 2019 22:19:04 +0000 (23:19 +0100)]
package/uboot-omap: backport patches to fix build
* 106: fix build when libfdt-devel is installed on host
* 107: fix stdbool.h includes
Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
Daniel Golle [Wed, 27 Mar 2019 21:59:03 +0000 (22:59 +0100)]
wireguard: introduce 'nohostroute' option
Instead of creating host-routes depending on fwmark as (accidentally)
pushed by commit
1e8bb50b93 ("wireguard: do not add host-dependencies if fwmark is set")
use a new config option 'nohostroute' to explicitely prevent creation
of the route to the endpoint.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Daniel Golle [Wed, 27 Mar 2019 21:52:05 +0000 (22:52 +0100)]
IB: fix generating .profile.mk for profiles without metadata
Fixes
d6fa04a437 ("IB: include SUPPORTED_DEVICES in 'make info' output")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Daniel Golle [Tue, 19 Mar 2019 15:47:17 +0000 (16:47 +0100)]
wireguard: do not add host-dependencies if fwmark is set
The 'fwmark' option is used to define routing traffic to
wireguard endpoints to go through specific routing tables.
In that case it doesn't make sense to setup routes for
host-dependencies in the 'main' table, so skip setting host
dependencies if 'fwmark' is set.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Hans Dedecker [Wed, 27 Mar 2019 20:03:02 +0000 (21:03 +0100)]
odhcpd: update to latest git HEAD (FS#2204)
420945c netlink: fix IPv6 address updates (FS#2204)
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
Koen Vandeputte [Wed, 27 Mar 2019 15:46:39 +0000 (16:46 +0100)]
kernel: fix missing dependency in 4.14.108
The 4.14.108 bump introduced a missing dependency when building
specific netfilters.
Thsi was not seen as the error does not occur on all targets.
Thanks to Jo-Philipp Wich for providing the fix
Fixes: af6c86dbe56e ("kernel: bump 4.14 to 4.14.108")
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Felix Fietkau [Wed, 27 Mar 2019 12:03:01 +0000 (13:03 +0100)]
mt76: update to the latest version
f2a18f5 mt76x02: introduce mt76x02_beacon.c
91ade88 mt76x02: add hrtimer for pre TBTT for USB
6370485 mt76x02: introduce beacon_ops
37af803 mt76x02u: implement beacon_ops
41d6190 mt76x02: generalize some mmio beaconing functions
dcccc04 mt76x02u: add sta_ps
5ac5289 mt76x02: disable HW encryption for group frames
e284cc2 mt76x02u: implement pre TBTT work for USB
77e56b8 mt76x02: make beacon slots bigger for USB
d4c740f mt76x02u: add mt76_release_buffered_frames
65e6344 mt76: unify set_tim
f720e49 mt76x02: enable AP mode for USB
cf1838d mt76usb: change mt76u_submit_buf
16b2ccf mt76: remove rx_page_lock
e1bfbeb mt76usb: change mt76u_fill_rx_sg arguments
e9c0171 mt76usb: use usb_dev private data
a4eb5db mt76usb: remove mt76u_buf redundant fileds
3f9b68d mt76usb: move mt76u_buf->done to queue entry
4a366bd mt76usb: remove mt76u_buf and use urb directly
0904bc4 mt76usb: remove MT_RXQ_MAIN queue from mt76u_urb_alloc
42f2899 mt76usb: resue mt76u_urb_alloc for tx
4d4d73a mt76usb: remove unneded sg_init_table
57309c7 mt76usb: allocate urb and sg as linear data
2e89721 mt76usb: remove queue variable from rx_tasklet
30a256a mt76x02: remove extra_tx_headroom (obsoleted by mac8211 skb aligning)
ae166b0 Revert "mt76: mt7603: store software PN/IV in wcid"
bf6e72d Revert "mt76: mt76x02: store software PN/IV in wcid"
a11b673 mt76: fix tx power issues
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Koen Vandeputte [Mon, 25 Mar 2019 10:40:22 +0000 (11:40 +0100)]
kernel: bump 4.14 to 4.14.108
Refreshed all patches.
Altered patches:
- 950-0033-i2c-bcm2835-Add-debug-support.patch
Compile-tested on: ar71xx, cns3xxx, imx6, x86_64
Runtime-tested on: ar71xx, cns3xxx, imx6
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Koen Vandeputte [Mon, 25 Mar 2019 10:37:17 +0000 (11:37 +0100)]
kernel: bump 4.9 to 4.9.165
Refreshed all patches.
Compile-tested on: ar7
Runtime-tested on: none
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Stijn Tintel [Tue, 26 Mar 2019 17:35:55 +0000 (19:35 +0200)]
scripts/gen_image_generic.sh: fail on errors
The script always exits with value 0, even if some of the commands fail.
This can potentially create broken, unbootable images, e.g. when
make_ext4fs fails due to TARGET_KERNEL_PARTSIZE being too small for the
kernel. Avoid this by failing the script when any command fails.
Acked-by: Jo-Philipp Wich <jo@mein.io>
Acked-by: Petr Štetiar <ynezz@true.cz>
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Koen Vandeputte [Fri, 22 Mar 2019 12:02:40 +0000 (13:02 +0100)]
ar71xx: add support for MikroTik RouterBOARD 922UAGS-5HPacD
This patch adds support for the MikroTik RouterBOARD 922UAGS-5HPacD
with a built-in 802.11ac High-Power radio (31dBm).
See https://mikrotik.com/product/RB922UAGS-5HPacD for more info.
Specifications:
- SoC: Qualcomm Atheros QCA9557 (720 MHz)
- RAM: 128 MB
- Storage: 128 MB NAND
- Wireless: external QCA9882 802.11a/ac 2x2:2
- Ethernet: 1x 1000/100/10 Mbps, integrated, via AR8031 PHY, passive PoE-in 24V
- SFP: 1x host
- USB: 1x 2.0 type A
- PCIe: 1x Mini slot (also contains USB 2.0 for 3G/LTE modems)
- SIM slot: 1x mini-SIM
Working:
- Board/system detection
- NAND storage detection
- PCIe
- USB: Type A & mini PCIe
- Wireless
- Ethernet
- LED's (excl. SFP and RSSI levels)
- Reset button
- Sysupgrade
Not working:
- SFP cage
Installation:
- Boot vmlinux-initramfs image via BOOTP/TFTP and then flash sysupgrade
image using "sysupgrade -n"
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
Hauke Mehrtens [Thu, 21 Mar 2019 16:57:00 +0000 (17:57 +0100)]
mvebu: Add dependency to kmod-i2c-mux-pca954x for armada-macchiatobin
This driver is needed for the I2C mux on the board.
Signed-off-by: Hauke Mehrtens <hauke.mehrtens@intel.com>
Hauke Mehrtens [Tue, 26 Mar 2019 00:23:24 +0000 (01:23 +0100)]
mvebu: Refresh kernel configuration
This refreshes the current kernel configuration to remove unneeded
options, add some automatically added ones and reorders them. The normal
build did this automatically, so the builds already used this
configuration.
CONFIG_HW_RANDOM_OMAP is explicitly activated for the cortexa72
subtarget because it has an inside-secure,safexcel-eip76 IP core.
This was done with this command on the cortexa9 subtarget:
make kernel_oldconfig
and this one on the other subtargets:
make kernel_oldconfig CONFIG_TARGET=subtarget
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Hauke Mehrtens [Thu, 21 Mar 2019 16:56:59 +0000 (17:56 +0100)]
mvebu: Fix typo in MACCHIATOBin detection
The name in the device tree file is written with two C.
Signed-off-by: Hauke Mehrtens <hauke.mehrtens@intel.com>
Hauke Mehrtens [Thu, 21 Mar 2019 18:16:18 +0000 (19:16 +0100)]
linux: Add kmod-sched-act-vlan
This allows to configure rules to push or pop vlan headers.
Signed-off-by: Hauke Mehrtens <hauke.mehrtens@intel.com>
Hauke Mehrtens [Thu, 21 Mar 2019 18:16:17 +0000 (19:16 +0100)]
linux: Add kmod-sched-flower
This allows to classify packets based on a configurable combination
of packet keys and masks.
Signed-off-by: Hauke Mehrtens <hauke.mehrtens@intel.com>
Hauke Mehrtens [Thu, 21 Mar 2019 18:16:16 +0000 (19:16 +0100)]
linux: Add kmod-sched-mqprio
This adds Multi-queue priority scheduler (MQPRIO).
Signed-off-by: Hauke Mehrtens <hauke.mehrtens@intel.com>
Hauke Mehrtens [Thu, 21 Mar 2019 18:16:15 +0000 (19:16 +0100)]
linux: Add kmod-crxypto-xcbc
This can be used for IPsec.
Signed-off-by: Hauke Mehrtens <hauke.mehrtens@intel.com>
Konstantin Demin [Mon, 25 Mar 2019 19:00:28 +0000 (22:00 +0300)]
dropbear: split ECC support to basic and full
- limit ECC support to ec*-sha2-nistp256:
* DROPBEAR_ECC now provides only basic support for ECC
- provide full ECC support as an option:
* DROPBEAR_ECC_FULL brings back support for ec{dh,dsa}-sha2-nistp{384,521}
- update feature costs in binary size
Signed-off-by: Konstantin Demin <rockdrilla@gmail.com>
Konstantin Demin [Mon, 25 Mar 2019 18:59:47 +0000 (21:59 +0300)]
dropbear: rewrite init script startup logic to handle both host key files
Signed-off-by: Konstantin Demin <rockdrilla@gmail.com>
Konstantin Demin [Mon, 25 Mar 2019 18:42:09 +0000 (21:42 +0300)]
dropbear: change type of config option "Port" to scalar type "port"
it was never used anywhere, even LuCI works with "Port" as scalar type.
Signed-off-by: Konstantin Demin <rockdrilla@gmail.com>
Konstantin Demin [Mon, 25 Mar 2019 18:42:01 +0000 (21:42 +0300)]
dropbear: introduce config option "keyfile" (replacement for "rsakeyfile")
* option "keyfile" is more generic than "rsakeyfile".
* option "rsakeyfile" is considered to be deprecated and should be removed
in future releases.
* warn user (in syslog) if option "rsakeyfile" is used
* better check options ("rsakeyfile" and "keyfile"): don't append
"-r keyfile" to command line if file is absent (doesn't exist or empty),
warn user (in syslog) about such files
Signed-off-by: Konstantin Demin <rockdrilla@gmail.com>
Konstantin Demin [Mon, 25 Mar 2019 18:41:45 +0000 (21:41 +0300)]
dropbear: add initial support for ECC host key
Signed-off-by: Konstantin Demin <rockdrilla@gmail.com>
Konstantin Demin [Mon, 25 Mar 2019 18:41:37 +0000 (21:41 +0300)]
dropbear: fix regression where TTY modes weren't reset for client
cherry-pick upstream commit
7bc6280613f5ab4ee86c14c779739070e5784dfe
Signed-off-by: Konstantin Demin <rockdrilla@gmail.com>
Konstantin Demin [Mon, 25 Mar 2019 18:41:27 +0000 (21:41 +0300)]
dropbear: honour CFLAGS while building bundled libtomcrypt/libtommath
Felix Fietkau pointed out that bundled libtomcrypt/libtommath do funny stuff with CFLAGS.
fix this with checking environment variable OPENWRT_BUILD in both libs.
change in dropbear binary size is drastical: 221621 -> 164277.
Signed-off-by: Konstantin Demin <rockdrilla@gmail.com>
Konstantin Demin [Mon, 25 Mar 2019 18:40:59 +0000 (21:40 +0300)]
dropbear: fix hardening flags during configure
compiler complains about messed up CFLAGS in build log:
<command-line>: warning: "_FORTIFY_SOURCE" redefined
<command-line>: note: this is the location of the previous definition
and then linker fails:
mips-openwrt-linux-musl-gcc [...] -o dropbearmulti [...]
collect2: fatal error: ld terminated with signal 11 [Segmentation fault]
compilation terminated.
/staging_dir/toolchain-mips_24kc_gcc-8.2.0_musl/mips-openwrt-linux-musl/bin/ld: /tmp/cc27zORz.ltrans0.ltrans.o: relocation R_MIPS_HI16 against `cipher_descriptor' can not be used when making a shared object; recompile with -fPIC
/staging_dir/toolchain-mips_24kc_gcc-8.2.0_musl/mips-openwrt-linux-musl/bin/ld: /tmp/cc27zORz.ltrans1.ltrans.o: relocation R_MIPS_HI16 against `ses' can not be used when making a shared object; recompile with -fPIC
/staging_dir/toolchain-mips_24kc_gcc-8.2.0_musl/mips-openwrt-linux-musl/bin/ld: /tmp/cc27zORz.ltrans2.ltrans.o: relocation R_MIPS_HI16 against `cipher_descriptor' can not be used when making a shared object; recompile with -fPIC
/staging_dir/toolchain-mips_24kc_gcc-8.2.0_musl/mips-openwrt-linux-musl/bin/ld: BFD (GNU Binutils) 2.31.1 assertion fail elfxx-mips.c:6550
[...]
/staging_dir/toolchain-mips_24kc_gcc-8.2.0_musl/mips-openwrt-linux-musl/bin/ld: BFD (GNU Binutils) 2.31.1 assertion fail elfxx-mips.c:6550
make[3]: *** [Makefile:198: dropbearmulti] Error 1
make[3]: *** Deleting file 'dropbearmulti'
make[3]: Leaving directory '/build_dir/target-mips_24kc_musl/dropbear-2018.76'
make[2]: *** [Makefile:158: /build_dir/target-mips_24kc_musl/dropbear-2018.76/.built] Error 2
make[2]: Leaving directory '/package/network/services/dropbear'
This FTBFS issue was caused by hardening flags set up by dropbear's configure script.
By default, Dropbear offers hardening via CFLAGS and LDFLAGS,
but this may break or confuse OpenWrt settings.
Remove most Dropbear's hardening settings in favour of precise build,
but preserve Spectre v2 mitigations:
* -mfunction-return=thunk
* -mindirect-branch=thunk
Signed-off-by: Konstantin Demin <rockdrilla@gmail.com>
Konstantin Demin [Mon, 25 Mar 2019 18:40:38 +0000 (21:40 +0300)]
dropbear: bump to 2019.77
- drop patches applied upstream:
* 010-runtime-maxauthtries.patch
* 020-Wait-to-fail-invalid-usernames.patch
* 150-dbconvert_standalone.patch
* 610-skip-default-keys-in-custom-runs.patch
- refresh patches
- move OpenWrt configuration from patch to Build/Configure recipe,
thus drop patch 120-openwrt_options.patch
Signed-off-by: Konstantin Demin <rockdrilla@gmail.com>
Christian Lamparter [Mon, 25 Mar 2019 17:27:59 +0000 (18:27 +0100)]
ath10k-ct: Update to 2019-03-25
2e917efb607f ath10k: Add slow-pci bus work-around, sw-crypt blockack support.
cc73ceb0dbc7 ath10k: Fix out-of-tree compile for 4.16 driver.
4b3cf7c20972 ath10k: Improve tx-status reporting.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Christian Lamparter [Mon, 25 Mar 2019 17:14:05 +0000 (18:14 +0100)]
ath10k-firmware: update Candela Tech firmware images
Release notes since last time:
Release notes for wave-1:
- 2019-03-12: Add btcoex feature flag for 2.4Ghz only adapters,
backported from upstream 10.2 firmware.
- 2019-03-12: Support offloading decrypt of PMF blockack frames
to the host. This lets us do blockack with PMF and
rx-sw-crypt. Normal hwcrypt scenarios would not need this.
Release notes for wave-2:
- 2019-03-12: Fix crash when tearing down VI TID when pending frames
exist. Could reproduce this while doing rmmod when VI
traffic was flowing and PMF was enabled but broken.
Bad luck could rarely cause it to happen in more normal
config too.
- 2019-03-12: Support offloading decrypt of PMF blockack frames to
the host. This lets us do blockack with PMF and
rx-sw-crypt. Normal hwcrypt scenarios would not need this.
- 2019-03-12: Re-work problematic patch that attempted to fix transmit
on non-QOS tids. It appears buggy in several ways,
hopefully improved now. This was introduced last fall.
See github bug 78.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Christian Lamparter [Sun, 24 Mar 2019 21:00:15 +0000 (22:00 +0100)]
gemini: Classify Raidsonic NAS IB-4220-B as a NAS
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Christian Lamparter [Sun, 24 Mar 2019 20:59:06 +0000 (21:59 +0100)]
gemini: D-Link DNS-313 is a NAS
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Christian Lamparter [Sun, 24 Mar 2019 20:53:29 +0000 (21:53 +0100)]
apm821xx: MBL: set DEVICE_TYPE to NAS
The MyBook Live is a NAS.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Boris Krasnovskiy [Thu, 21 Mar 2019 03:00:51 +0000 (23:00 -0400)]
toolchain: ARM: Fix option conflict with multiarch
This problem exposed when compiling glibc, but applicable across the
board. gcc compiles runtime libraries for all supported architectures,
unless otherwise specified, and later selects applicable library based
-m[arch,cpu,*] options, thus these options should not be passed to gcc
as they break the compilation process.
Signed-off-by: Boris Krasnovskiy <borkra@gmail.com>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
[modified so it only touches ARM - I'm too chicken, changed authors email]
Boris Krasnovskiy [Sun, 10 Mar 2019 01:45:43 +0000 (20:45 -0500)]
toolchain: ARM: Fix toolchain compilation for gcc 8.x
Set the toolchain's ARM CPU and FPU architectures by utilizing' gcc's
--with-cpu / --with-fpu configure options that: "Specify which cpu
variant the compiler should generate code for by default. cpu will
be used as the default value of the -mcpu= switch."
This will resolve the following kernel compilation failures under
gcc 8.x on ARM because the kernel wants to set (possibly conflicting)
optimization flags.
.../ccyVnmrs.s:204: Error: selected processor does not support `dmb ish' in ARM mode
.../ccyVnmrs.s:215: Error: architectural extension `mp' is not allowed for the current base architecture
.../ccyVnmrs.s:216: Error: selected processor does not support `pldw [r4]' in ARM mode
Because this is a big change, the .config and toolchain need to be
refreshed (as in removed and regenerated).
Reported-by: Ansuel Smith <ansuelsmth@gmail.com>
Reported-by: Daniel Engberg <daniel.engberg.lists@pyret.net> [#1203]
Signed-off-by: Boris Krasnovskiy <borkra@gmail.com>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com> [extended commit message,
removed now-deprecated CPU_CFLAGS, changed author to gmail address]
Christian Lamparter [Tue, 19 Mar 2019 15:44:21 +0000 (16:44 +0100)]
ipq40xx: essedma: Add fix for memory allocation issues
This patch adds a ChromiumOS 3.18 patch [0] that fixes memory
allocation issues under memory pressure by keeping track
of missed allocs and rectify the omission at a later date.
It also adds ethtool counters for memory allocation
failures accounting so this can be verified.
[0] <https://chromium.googlesource.com/chromiumos/third_party/kernel/+/
d4e1e4ce6801f9eddce056c58f5a288864955265>
Reported-by: Chen Minqiang <ptpt52@gmail.com>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Deng Qingfang [Fri, 15 Mar 2019 18:05:04 +0000 (02:05 +0800)]
tools/ccache: update to 3.6
Update ccache to 3.6
Signed-off-by: Deng Qingfang <dengqf6@mail2.sysu.edu.cn>
Felix Fietkau [Sun, 24 Mar 2019 11:05:56 +0000 (12:05 +0100)]
ramips: allow packets with ttl=0
Some broken ISPs (e.g. Comcast) send DHCPv6 packets with hop limit=0.
This trips up the TTL=0 check in the PPE if enabled.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Ding Tengfei [Thu, 21 Mar 2019 11:50:01 +0000 (19:50 +0800)]
ath79: add support for COMFAST CF-E5/E7
COMFAST CF-E5/E7 is a outdoor 4G LTE AP with PoE support, based on
Qualcomm/Atheros QCA9531.
Short specification:
2x 10/100 Mbps Ethernet, with 24v PoE support
64 MB of RAM (DDR2)
16 MB of FLASH (SPI)
2T2R 2.4 GHz, 802.11b/g/n
built-in 1x 3 dBi antennas
output power (max): 80 mW (19 dBm)
Qucetel EC20 LTE MODULE(1x external detachable antenna)
Flash instruction:
Original firmware is based on OpenWrt.
Use sysupgrade image directly in vendor GUI.
Signed-off-by: Ding Tengfei <dtf@comfast.cn>
[commit subject fix]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Marcin Jurkowski [Sun, 16 Dec 2018 01:22:45 +0000 (02:22 +0100)]
ath79: add TP-Link TL-WR710N v1
This commit adds support for TP-Link TL-WR710N v1 router.
CPU: Atheros AR9331 400MHz
RAM: 32MB
FLASH: 8MiB
PORTS: 1 Port 100/10 LAN (connected to a switch), 1 Port 100/10 WAN
WiFi: Atheros AR9331 1x2:1 bgn
USB: ChipIdea HDRC USB2.0
LED: SYS
BTN: Reset
Sysupgrade from `ar71xx` works without glitches.
Network interfaces assigned for LAN and WAN ports are `eth1` and `eth0`
respectively, what's consistent with `ar71xx` target. Wireless radio
path is automatically upgraded from `platform/ar933x_wmac` to
`platform/ahb/
18100000.wmac`.
Signed-off-by: Marcin Jurkowski <marcin1j@gmail.com>
Chuanhong Guo [Sun, 20 Jan 2019 15:30:27 +0000 (23:30 +0800)]
ath79: add support for TP-Link TL-WR941N v7 (CN)
This adds support for the Chinese version of TL-WR941N v7.
It uses QCA9558+AR8236 while the international version
uses TP9343 instead.
Specification:
- SoC: Qualcomm Atheros QCA9558
- Flash: 4 MB
- RAM: 64 MB
- Ethernet: Atheros AR8236 with 5 FE ports
Flash instruction:
Upload the generated factory firmware on web interface.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
Chuanhong Guo [Fri, 11 Jan 2019 06:00:03 +0000 (14:00 +0800)]
ath79: ag71xx: remove switch driver in ag71xx
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
Chuanhong Guo [Fri, 11 Jan 2019 05:58:28 +0000 (13:58 +0800)]
ath79: use ar8216 for builtin switch
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
Chuanhong Guo [Wed, 23 Jan 2019 05:46:15 +0000 (13:46 +0800)]
generic: ar8216: introduce qca,mib-poll-interval property
This allows users to specify a shorter mib poll interval so that the
swconfig leds could behave normal with current get_port_stats()
implementation.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
Chuanhong Guo [Sun, 20 Jan 2019 14:25:25 +0000 (22:25 +0800)]
generic: ar8216: do a software reset for switch during hw_init
This applies to ar8216 and ar8236. QCA's newer U-boot will enable
the switch mdio master for FE switches which makes phy inaccessible
from CPU mdio. (e.g. on TP-Link TL-WR941N v7 Chinese version which
uses QCA9558+AR8236.) For these devices PHY probing is broken and
mdio device probing is a must. We also need to disable switch mdio
master in driver for later PHY initialization.
Do a soft reset during hw_init so that mdio master can be disabled
and expose PHYs to CPU mdio for later PHY accessing.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
Chuanhong Guo [Fri, 11 Jan 2019 05:18:30 +0000 (13:18 +0800)]
generic: ar8216: mib_work_func: read all port mibs everytime
ar8xxx_mib_capture will update mib counters for all ports. Current
code only update one port at a time and the data for other ports
are lost.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
Chuanhong Guo [Fri, 11 Jan 2019 03:51:54 +0000 (11:51 +0800)]
generic: ar8216: add support for get_port_stats()
Partially reverts commit
eff3549c5883a9abc5dbff00c084cabbcfdf4437.
AR7240 and AR9341 have buggy hardware switch LED trigger. The AR7240
one doesn't blink and the blinking of port0/port5 is reversed on
AR9341 if we swap PHY0 and PHY4. (Only blinking is reversed, which
means LED for PHY0 will lit when PHY0 is link up and will blink when
PHY4 has active link and vice versa.) On these two chips a software
swconfig LED trigger is required.
This commit adds swconfig port stats back but:
1. move checking of mib_t/rxb_id into ar8xxx_chip since we can't
distinguish ar7240sw and ar8216 using only chip id.
2. don't update mib counter in get_port_stat. This function is called
every 0.01s and this capturing procedure will take up a lot of CPU.
We already have a mib_work_func updating mib counters every 2s so
return the saved counter instead of fetching new data. The blinking
rate will be weird but it should solve the previously mentioned CPU
time problem.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
Chuanhong Guo [Thu, 10 Jan 2019 15:53:23 +0000 (23:53 +0800)]
generic: ar8216: add support for ar724x/ar933x builtin switch
This builtin switch is a bugless ar8216 with different mib counters
and gigabit cpu port.
Atheros uses the same device ID and it's impossible to distinguish
the standalone one and the builtin one. So we add support to mdio
device probe only.
This switch doesn't have buggy vlan tag so it's not needed to enable
atheros header. This commit changed ar8216_setup_port so that it can
be reused for this switch.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
Chuanhong Guo [Thu, 10 Jan 2019 15:31:35 +0000 (23:31 +0800)]
generic: ar8216: mdiodev: add qca,phy4-mii-enable option
This option allows setting phy4 as a phy connected directly to CPU.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
Chuanhong Guo [Thu, 10 Jan 2019 14:38:13 +0000 (22:38 +0800)]
generic: ar8216: ar8229: add phy_read/phy_write
the added function also works for ar8216 and will be used in the
following ar7240 support.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
Chuanhong Guo [Thu, 10 Jan 2019 11:30:35 +0000 (19:30 +0800)]
generic: ar8216: add support for separated mdio bus for phy access
Atheros FE switches have a builtin mdio master available for PHY
accessing and on ar724x/ar933x builtin switches this mdio master
is the only way of accessing PHYs.
After this patch if there is phy_read/phy_write method available
in ar8xxx_chip we register a separated mdio bus for accessing PHYs.
Still adds support for mdio device probing only since this isn't
needed for those switches registered using PHY probing.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
Chuanhong Guo [Thu, 10 Jan 2019 10:55:27 +0000 (18:55 +0800)]
generic: ar8216: add support for ar8229
ar8229 is the builtin switch in ar934x and later chips. There is
also a standalone version available and their registers/functions
are the same.
This commit added support for the builtin ar8229. The only thing
missing for standalone ar8229 should be phy modes. Since I don't
have a router using that, this commit doesn't add support for
other phy modes.
Only add its support for mdio-device probing method because the
current PHY probing can't return 1G speed when it's a FE switch.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
Chuanhong Guo [Thu, 10 Jan 2019 07:31:53 +0000 (15:31 +0800)]
generic: ar8216: add mdio-device probing support
currently only ar8327 and ar8236 are added since they are the only
two I could verify.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
Chuanhong Guo [Thu, 10 Jan 2019 06:54:56 +0000 (14:54 +0800)]
generic: ar8216: move ar8xxx_id_chip into ar8xxx_phy_probe
ar8xxx_id_chip is used to determine current ar8xxx_chip using switch
id and this isn't needed during mdiodev probing.
Move it out of ar8xxx_probe_switch so that we can skip it.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
Chuanhong Guo [Thu, 10 Jan 2019 05:23:42 +0000 (13:23 +0800)]
generic: ar8216: add device struct into struct ar8xxx_priv
dev has been taken up by switch_dev so it's named pdev instead.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
Chuanhong Guo [Thu, 10 Jan 2019 05:16:33 +0000 (13:16 +0800)]
generic: ar8216: drop duplicated include
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
Chuanhong Guo [Thu, 10 Jan 2019 05:05:00 +0000 (13:05 +0800)]
generic: ar8216: move chip id reading into a separate function
for mdio-device probing we still need to read chip id but ar8xxx_chip
can be determined using drvdata. We can't distinguish the buggy
standalone ar8216 and the builtin ar8216 in ar724x/ar933x using chip
id.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
Chuanhong Guo [Thu, 13 Dec 2018 07:14:10 +0000 (15:14 +0800)]
ath79: add support for linux 4.19
The following patches are dropped because they are merged upstream:
-0001-tty-serial-drop-QCA-pecific-SoC-symbols.patch
-0006-usb-drop-deprecated-symbols.patch
-0009-MIPS-ath79-add-lots-of-missing-registers.patch
-0010-MIPS-ath79-add-support-for-QCA953x-QCA956x-TP9343.patch
-0014-MIPS-ath79-finetune-cpu-overrides.patch
-0015-MIPS-ath79-enable-uart-during-early_prink.patch
-0016-MIPS-ath79-get-PCIe-controller-out-of-reset.patch
This patch is dropped due to the introduction of spi-mem framework:
-461-spi-ath79-add-fast-flash-read.patch
Thank to Michael Marley @mamarley for his work on this patch:
-910-unaligned_access_hacks.patch
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
[synchronized kernel config with make kernel_oldconfig]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Chuanhong Guo [Thu, 13 Dec 2018 07:12:01 +0000 (15:12 +0800)]
ath79: ag71xx: pass correct device pointer to dma functions
linux 4.19 doesn't accept a NULL device for these functions.
It also complains that the device struct in net_device doesn't have
a dma_mask set.
Pass the device struct from platform_device for these functions.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
Chuanhong Guo [Wed, 12 Dec 2018 11:09:35 +0000 (19:09 +0800)]
ath79: ag71xx: add support for timer functions in linux 4.15+
Kernel newer than 4.15 dropped "data" field and used from_timer
to cast out the parent struct pointer for current timer.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
Pawel Dembicki [Mon, 19 Mar 2018 18:15:29 +0000 (19:15 +0100)]
ramips: add support for DLINK DIR-510L
The DIR-510L Wireless Router are based on the MT7620A SoC.
Specification:
-MediaTek MT7620A (580 Mhz)
-128 MB of RAM
-16 MB of FLASH
-802.11bgn radio
-1x 10/100 Mbps Ethernet
-2x internal, non-detachable antennas
-UART (J3) header on PCB (57600 8n1)
-1x bi-color LED (GPIO-controlled), 2x button
-JBOOT bootloader
Known issues:
-Ethernet port is used as LAN
-No communication with charger IC. (uart bitbang needed)
Installation:
Apply factory image via d-link http web-gui.
How to revert to OEM firmware:
1.) Push the reset button and turn on the power. Wait until LED start blinking (~10sec.)
2.) Upload original factory image via JBOOT http (IP: 192.168.123.254)
3.) If http doesn't work, it can be done with curl command:
curl -F FN=@XXXXX.bin http://192.168.123.254/upg
where XXXXX.bin is name of firmware file.
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
[fixed whitespace issue in 10-rt2x00-eeprom]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Pawel Dembicki [Thu, 19 Apr 2018 17:36:55 +0000 (19:36 +0200)]
firmware-utils: mkdlinkfw: add kernel image offset
Some boards with JBOOT have partiton between bootloader
and kernel image. This patch add possibility to change kernel
partition start address.
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
Qin Wei [Tue, 5 Mar 2019 01:58:55 +0000 (09:58 +0800)]
ramips: fix wrong i2s clock unit from kHz to MHz
clk_get_rate returns the current clock rate in Hz for a clock source so
if we divide it by 1M, then we get frequency in MHz and not kHz.
Signed-off-by: Qin Wei <support@vocore.io>
[added missing commit message, and fixed author with SoB from PR message]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Felix Fietkau [Sat, 23 Mar 2019 17:00:00 +0000 (18:00 +0100)]
mt76: update to the latest version
4d8c7e8 mt76: mt76x02: send no-skb tx status without holding the status lock
7e9e9ad mt76: mt7603: add missing initialization for dev->ps_lock
3a7e6bb mt76: fix potential deadlock on cancelling workqueues
deacb8f mt76: fix using mac80211 tx skb header padding
c9402eb mt76: use napi polling for tx cleanup
60e508e mt76: use readl/writel instead of ioread32/iowrite32
5912e8a mt7603: fix sequence number assignment
95a83cc mt7603: send BAR after powersave wakeup
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Koen Vandeputte [Wed, 20 Mar 2019 12:28:57 +0000 (13:28 +0100)]
kernel: bump 4.14 to 4.14.107
Refreshed all patches.
Compile-tested on: ar71xx, cns3xxx, imx6, x86_64
Runtime-tested on: ar71xx, cns3xxx, imx6, x86_64
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Koen Vandeputte [Wed, 20 Mar 2019 12:27:16 +0000 (13:27 +0100)]
kernel: bump 4.9 to 4.9.164
Refreshed all patches.
Compile-tested on: ar7
Runtime-tested on: none
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Koen Vandeputte [Thu, 21 Mar 2019 14:08:26 +0000 (15:08 +0100)]
imx6: fix legacy IRQ support (4.19)
The PCIe DWC host controller is now using MSI
(Message-signaled-interrupts) by default.
While ath9k itself does support MSI here, a lot of wlan adapters do not.
Avoid non-functioning cards by simply continue to disable MSI for now.
This can be done by appending "pci=nomsi" to the boot cmdline.
Also an extra fix needs to be backported which avoids MSI initialization
which prevented legacy IRQ's init from taking over.
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Koen Vandeputte [Thu, 21 Mar 2019 14:02:43 +0000 (15:02 +0100)]
imx6: enable PCIe (4.19)
The DWC host controller symbols are now depending on a few others
Fixes: ca1b93f038a5 ("imx6: add support for kernel 4.19")
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Koen Vandeputte [Thu, 21 Mar 2019 16:00:24 +0000 (17:00 +0100)]
imx6: enable crypto acceleration (4.19)
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Koen Vandeputte [Thu, 21 Mar 2019 16:38:44 +0000 (17:38 +0100)]
imx6: enable crypto acceleration
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Koen Vandeputte [Thu, 21 Mar 2019 13:56:13 +0000 (14:56 +0100)]
imx6: refresh kernel configs
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Hans Dedecker [Fri, 22 Mar 2019 08:23:48 +0000 (09:23 +0100)]
glibc: update to latest 2.27 commit
1ab314d8d3 S390: Mark vx and vxe as important hwcap.
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
Tobias Schramm [Tue, 8 Jan 2019 14:27:57 +0000 (15:27 +0100)]
ath79: Add support for Ubiquiti NanoBeam AC
The NanoBeam is a small AR9342 based directional 5 GHz AC CPE with hardware
almost identical to the Ubiquiti NanoStation AC loco. Over the NanoStation
AC loco it has 5 additional LEDs. Four of those LEDs are used as rssi
indicators, the fifth LED is used as an ethernet link/activity indicator.
CPU: Atheros AR9342 SoC
RAM: 64 MB DDR2
Flash: 16 MB NOR SPI
WLAN: QCA988X
Ports: 1x GbE
Flashing procedure is identical to the NanoStation AC loco and can be performed
either via serial or the factory firmware upgrade.
Serial flashing:
1. Connect to serial header on device (8N1 115200)
2. Power on device and enter uboot console
3. Set up tftp server serving an openwrt initramfs build
4. Load initramfs build using the command tftpboot in the uboot cli
5. Boot the loaded image using the command bootm
6. Copy squashfs openwrt sysupgrade build to the booted device
7. Use mtd to write sysupgrade to partition "firmware"
8. Reboot and enjoy
Flashing through factory firmware:
1. Ensure firmware version v8.5.0.36727 is installed. Up/downgrade to this exact version.
2. Patch fwupdate.real binary using `hexdump -Cv /bin/ubntbox | sed 's/14 40 fe fe/00 00 00 00/g' | hexdump -R > /tmp/fwupdate.real`
3. Make the patched fwupdate.real binary executable using `chmod +x /tmp/fwupdate.real`
4. Copy the squashfs factory image to /tmp on the device
5. Flash OpenWRT using `/tmp/fwupdate.real -m <squashfs-factory image>`
6. Wait for the device to reboot
Thanks to @cybermaus for testing!
Tested-by: Maurits van Dueren den Hollander <cybermaus@gmail.com>
Signed-off-by: Tobias Schramm <tobleminer@gmail.com>
Xavier Douville [Thu, 21 Mar 2019 13:21:34 +0000 (09:21 -0400)]
ar71xx: Add support for Mikrotik RB SXT 2nD r3
The Mikrotik RouterBOARD SXT 2nD r3 is an outdoor WiFi AP / CPE
with a single 2.4 GHz radio and a 100 Mbps Ethernet port.
The device similar to the SXT 2nD r2, but it has SPI NOR flash instead
of NAND flash.
Hardware
--------
CPU: Atheros AR9344 (600 MHz)
RAM: 64 MiB
FLASH: 16 MiB SPI NOR W25Q128
ETH: 1x 100 Mbps Atheros AG71xx
WiFi: 2T2R 802.11b/g/n (ath9k)
Power: Passive PoE 8-30 V
Installation instructions:
1. Boot openwrt-ar71xx-mikrotik-vmlinux-initramfs.elf using a
DHCP+TFTP server.
2. Erase the "firmware" partition using the mtd command. This should
no longer be required once this patch is merged.
3. Use sysupgrade to install to flash. The file
openwrt-ar71xx-mikrotik-rb-nor-flash-16M-squashfs-sysupgrade.bin
should be used.
Signed-off-by: Xavier Douville <github@douville.org>
Florian Eckert [Mon, 28 May 2018 09:26:50 +0000 (11:26 +0200)]
build: suppress error output in feeds.mk
If no feed.conf or feeds.conf.default is found on image generation with
the imagebuilder we always get the following message "Unable to open
feeds configuration at <dir>/scripts/feeds line 48." on std error.
To get rid off this needless warning on image generation with the
imagebuilder supress the output in feeds.mk.
Signed-off-by: Florian Eckert <fe@dev.tdt.de>
Hauke Mehrtens [Thu, 21 Mar 2019 15:40:53 +0000 (16:40 +0100)]
netifd: update to latest git HEAD
a8cf037 netifd: wireless: Add support for GCMP cipher
34a70b6 netifd: wireless: Add support for 802.11ad
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
projects / openwrt / staging / nbd.git / log