Piotr Dymacz [Thu, 23 Mar 2017 22:49:28 +0000 (23:49 +0100)]
ar71xx: tp-link.mk: always include device version in image and DEVICE_TITLE
There are currently several supported TP-Link devices without specified
version number in image name and/or DEVICE_TITLE (e.g. WBS210, WBS510,
TL-WR810N, TL-WA7510N, TL-WPA8630), but vendor website shows that there
are already more than one version of them on the market.
For devices like Archer C5, which second version is based on a total
different platform, missing version number in DEVICE_TITLE (used in
menuconfig) might be misleading for users.
To make it less confusing for users and easier to maintain in future,
include version number in image name and DEVICE_TITLE for all TP-Link
devices, even if there is only one version of device at the moment.
Also, keep DEVICE_TITLE in same format for all TP-Link devices.
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
Acked-by: John Crispin <john@phrozen.org>
Ron Angeles [Tue, 28 Mar 2017 01:55:48 +0000 (18:55 -0700)]
ar71xx: add userspace support for Mikrotik RB2011iL
Kernel/hardware support for this board has been implemented since
Chaos Calmer. This set of patches is to get the board identified in
userland. This will allow support for things like sysupgrade,
configuring initial LED state, configuring initial switch state, etc.
Signed-off-by: Ron Angeles <ronangeles@gmail.com>
Vittorio Gambaletta [Sun, 26 Mar 2017 07:55:44 +0000 (09:55 +0200)]
ar71xx: add TP-LINK TL-WR841N/ND v12 image
This router has the same hardware as TP-LINK TL-WR841N/ND v11 (same FCC
ID, same TFTP image name...).
If the stock firmware web interface doesn't accept LEDE factory image,
it can be flashed via the U-Boot TFTP recovery mode, by long-pressing
the reset button after power on.
The TFTP image name is wr841nv11_tp_recovery.bin (yes, v11, not v12).
Signed-off-by: Vittorio Gambaletta <openwrt@vittgam.net>
Hans Dedecker [Sun, 2 Apr 2017 19:13:08 +0000 (21:13 +0200)]
netifd: fix fw3 warnings in dhcp script
Fix fw3 warnings in dhcp script in case fw3 is not enabled
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
Felix Fietkau [Mon, 27 Mar 2017 08:21:24 +0000 (10:21 +0200)]
build: move PKG_CONFIG_DEPENDS from feeds.mk to opkg
Normal packages don't rely on the feed configuration variables for the
build step
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Philip Prindeville [Tue, 7 Feb 2017 03:33:36 +0000 (20:33 -0700)]
build: allow specifying flow-control to grub on serial console
On the more sophisticated (i.e. deeper FIFO) serial controllers,
flow-control might be needed to avoid dropping output.
Signed-off-by: Philip Prindeville <philipp@redfish-solutions.com>
Philip Prindeville [Wed, 22 Mar 2017 03:55:23 +0000 (21:55 -0600)]
kexec-tools: get kexec running on MUSL and x86 hardware
Couple of important upstream patches (slated for 2.0.15) that
are necessary for kexec to run on MUSL and on x86 hardware.
Signed-off-by: Philip Prindeville <philipp@redfish-solutions.com>
Philip Prindeville [Mon, 6 Feb 2017 22:26:49 +0000 (15:26 -0700)]
busybox: don't install NTP scripts if NTP isn't configured
If you're using Chrony or NTPD you don't want the busybox NTP server
as well. Make it's installation truly conditional.
Signed-off-by: Philip Prindeville <philipp@redfish-solutions.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name> [simplify]
Ye Tao [Sun, 19 Feb 2017 12:57:11 +0000 (21:57 +0900)]
modules: Add kmod-igbvf kernel module for Intel(R) 82576 Virtual Function Ethernet adapters
Intel(R) 82576 is an adapter which supports SR-IOV. Thus the host can
assign Virtual Functions (VFs) to different VMs by the PCI-E Passthrough
(e.g. VFIO for KVM), to gain different advantages (performance, VF to VF
communications, host kernel offload, etc.).
The driver of the passthroughed VFs is the igbvf (igb is NOT
compatible).
This is essential for VM guests, to enable them to utilize this feature.
Signed-off-by: Ye Tao <tydus@hongo.wide.ad.jp>
Hauke Mehrtens [Sun, 2 Apr 2017 09:01:30 +0000 (11:01 +0200)]
kernel: update kernel 4.4 to 4.4.59
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Hauke Mehrtens [Sun, 2 Apr 2017 08:29:55 +0000 (10:29 +0200)]
kernel: update kernel 4.9 to 4.9.20
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
John Crispin [Sun, 2 Apr 2017 05:50:41 +0000 (07:50 +0200)]
kernel: fix ubi auto attach logging
The patch is missing a trailing new line
Signed-off-by: John Crispin <john@phrozen.org>
Hans Dedecker [Sat, 1 Apr 2017 11:56:44 +0000 (13:56 +0200)]
odhcpd: update to git HEAD version (FS#635)
3d9f406 rework IPv6 dns address selection (FS#635)
bc6c3ac ndp: keep an exact copy of IPv6 interface addresses
6eb1e01 ndp: code cleanup
eea7d03 rework IPv6 address dump logic
24d21c7 ndp: add syslog debug tracing
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
Daniel Golle [Thu, 30 Mar 2017 16:08:49 +0000 (18:08 +0200)]
mac80211: rt2x00: import upstream changes and rebase our patches
Some of our local patches have been accepted upstream. And there are
some more relevant changes (mostly for rt2800usb). Import them and
rebase our remaining local patches on top.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Christian Mehlis [Sun, 26 Feb 2017 11:25:57 +0000 (12:25 +0100)]
ar71xx: Compex WPJ563 support
Specification:
- SoC: Qualcomm Atheros QCA9563 (775 MHz, MIPS 74Kc)
- RAM: 128 MiB
- Storage: 16MB NOR flash
- Wireless: Built into QCA9563 (Dragonfly), PHY modes b/g/n, 3x3 MIMO
- Ethernet: 2x1G
Tested and working:
- ethernet / switch / lan / wan
- 2.4GHz SoC wifi
- PCIe
- leds
- buzzer
Ramload:
- tftpboot 0x84000000 lede-ar71xx-generic-wpj563-16M-initramfs-uImage.bin
- bootm 0x84000000
Install:
- tftpboot 0x80500000 lede-ar71xx-generic-wpj563-16M-squashfs-sysupgrade.bin
- erase 0x9f030000 +$filesize
- erase 0x9f680000 +1
- cp.b $fileaddr 0x9f030000 $filesize
Erasing 0x9f680000 is required because uboot defines
"bootcmd=bootm 0x9f680000 || bootm 0x9f030000", so it first tries to boot
the higher address. I think the 16 mb flash are intended to be used as
8+8mb for a fallback image. In my hardware only the lower address has a
bootable image. But to make sure future hardware will boot lede too, I
erase one block, so uboot will skip this address.
Signed-off-by: Christian Mehlis <christian@m3hlis.de>
Vittorio Gambaletta [Sun, 26 Mar 2017 08:08:20 +0000 (10:08 +0200)]
ar8327: Add workarounds for AR8337 switch.
RGMII RX delay setting needs to be always specified for AR8337 to
avoid port 5 RX hang on high traffic / flood conditions.
Also, the HOL registers that set per-port and per-packet-priority
buffer sizes are updated with the reduced values suggested by the
QCA switch team.
Finally, AR8327 reserved register fixups are disabled for the AR8337.
This patch is adapted from the Code Aurora QSDK, but with magic
values mapped to proper defines.
Signed-off-by: Vittorio Gambaletta <openwrt@vittgam.net>
Karl Vogel [Wed, 29 Mar 2017 09:39:35 +0000 (11:39 +0200)]
dnsmasq: use logical interface name for dhcp relay config
The relay section should use the logical interface name and
not the linux network device name directly. This to be
consistent with other sections of the dnsmasq config where
'interface' means the logical interface.
Signed-off-by: Karl Vogel <karl.vogel@gmail.com>
John Crispin [Wed, 29 Mar 2017 07:22:46 +0000 (09:22 +0200)]
ar71xx: drop default CONSOLE values
Compex boards dont need to set these as they are default.
Signed-off-by: John Crispin <john@phrozen.org>
John Crispin [Wed, 29 Mar 2017 07:18:13 +0000 (09:18 +0200)]
fstools: update to latest git HEAD
20c16fc cmake: Make blockd link against libjson-c
92b4c2c libfstools: add basic documentation of mount functions
Signed-off-by: John Crispin <john@phrozen.org>
Christian Mehlis [Tue, 28 Mar 2017 19:16:43 +0000 (21:16 +0200)]
ar71xx: move Compex WPJ342 to generic build target
Signed-off-by: Christian Mehlis <christian@m3hlis.de>
Christian Mehlis [Tue, 28 Mar 2017 19:14:49 +0000 (21:14 +0200)]
ar71xx: move Compex WPJ344 to generic build target
Signed-off-by: Christian Mehlis <christian@m3hlis.de>
Christian Mehlis [Tue, 28 Mar 2017 19:12:48 +0000 (21:12 +0200)]
ar71xx: move Compex WPJ531 to generic build target
Signed-off-by: Christian Mehlis <christian@m3hlis.de>
Christian Mehlis [Tue, 28 Mar 2017 19:09:37 +0000 (21:09 +0200)]
ar71xx: move Compex WPJ558 to generic build target
Signed-off-by: Christian Mehlis <christian@m3hlis.de>
Philip Prindeville [Tue, 10 Jan 2017 00:18:21 +0000 (17:18 -0700)]
kernel: add w83627hf-wdt watchdog timer module
This is a 3rd party chipset which is not present on all Intel
reference designs, so make it a module rather than baked in (this
will also alleviate conflicts with drivers which also detect some
of the same chipsets).
Signed-off-by: Philip Prindeville <philipp@redfish-solutions.com>
Philip Prindeville [Tue, 20 Dec 2016 20:26:48 +0000 (13:26 -0700)]
kernel: kmod packaging for Intel 10G ethernet ixgbe driver
A lot of Ivybridge and Haswell servers have the 82598/82599 Ethernet
controllers.
Signed-off-by: Philip Prindeville <philipp@redfish-solutions.com>
Yousong Zhou [Tue, 28 Mar 2017 09:41:14 +0000 (17:41 +0800)]
firewall: document rules for IPSec ESP/ISAKMP with 'name' option
These are recommended practices by REC-22 and REC-24 of RFC6092:
"Recommended Simple Security Capabilities in Customer Premises Equipment
(CPE) for Providing Residential IPv6 Internet Service"
Fixes FS#640
Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
Thomas Reifferscheid [Mon, 27 Mar 2017 22:01:59 +0000 (00:01 +0200)]
ipq8064: fix dwc3-of-simple module unloading
Without patch unloading the dwc3-of-simple module went stuck after
successfully removing hcd.1 during the hcd.0 removal:
root@LEDE:/# rmmod dwc3-of-simple
[ 21.391846] xhci-hcd xhci-hcd.1.auto: remove, state 1
[ 21.391931] usb usb4: USB disconnect, device number 1
[ 21.397038] xhci-hcd xhci-hcd.1.auto: USB bus 4 deregistered
[ 21.401111] xhci-hcd xhci-hcd.1.auto: remove, state 1
[ 21.406685] usb usb3: USB disconnect, device number 1
[ 21.412848] xhci-hcd xhci-hcd.1.auto: USB bus 3 deregistered
[ 21.417248] xhci-hcd xhci-hcd.0.auto: remove, state 1
[ 21.422521] usb usb2: USB disconnect, device number 1
followed by nothing.
Sometimes a stall CPU was detected, or a kernel panic,
or a reboot occurred after a couple of minutes.
At the same time unloading the dwc3 module followed by dwc3-of-simple
module was working repeatedly.
root@LEDE:/# rmmod dwc3
[ 53.827328] xhci-hcd xhci-hcd.1.auto: remove, state 1
[ 53.827412] usb usb4: USB disconnect, device number 1
[ 53.832630] xhci-hcd xhci-hcd.1.auto: USB bus 4 deregistered
[ 53.836452] xhci-hcd xhci-hcd.1.auto: remove, state 1
[ 53.842314] usb usb3: USB disconnect, device number 1
[ 53.848412] xhci-hcd xhci-hcd.1.auto: USB bus 3 deregistered
[ 53.852542] xhci-hcd xhci-hcd.0.auto: remove, state 1
[ 53.857882] usb usb2: USB disconnect, device number 1
[ 53.863956] xhci-hcd xhci-hcd.0.auto: USB bus 2 deregistered
[ 53.867875] xhci-hcd xhci-hcd.0.auto: remove, state 1
[ 53.873696] usb usb1: USB disconnect, device number 1
[ 53.879742] xhci-hcd xhci-hcd.0.auto: USB bus 1 deregistered
root@LEDE:/# rmmod dwc3-of-simple
root@LEDE:/#
For the non-working case, the code was stuck in a readl() in
http://lxr.free-electrons.com/source/drivers/usb/host/xhci.c#L91
because
http://lxr.free-electrons.com/source/drivers/usb/dwc3/dwc3-of-simple.c#L126
was disabling the wrong clocks when removing hcd.1 (it was disabling
the clock of hcd.0). That's why the readl() went stuck when removing
hcd.0
The patch however addresses the clock assignment from the .dtsi
file. Most probably it went into openwrt here:
https://dev.openwrt.org/browser/trunk/target/linux/ipq806x/patches-3.18/101-ARM-qcom-add-USB-nodes-to-ipq806x-ap148.patch?rev=45261
copied from Qualcomms attempt here: https://lkml.org/lkml/2015/11/20/116
Now unloading and repeated module loading is working just fine,
no matter if you'd remove dwc3-of-simple or dwc3.
root@LEDE:/# rmmod dwc3-of-simple
[ 24.089679] xhci-hcd xhci-hcd.1.auto: remove, state 1
[ 24.089765] usb usb4: USB disconnect, device number 1
[ 24.094856] xhci-hcd xhci-hcd.1.auto: USB bus 4 deregistered
[ 24.098963] xhci-hcd xhci-hcd.1.auto: remove, state 1
[ 24.104522] usb usb3: USB disconnect, device number 1
[ 24.111194] xhci-hcd xhci-hcd.1.auto: USB bus 3 deregistered
[ 24.115086] xhci-hcd xhci-hcd.0.auto: remove, state 1
[ 24.120396] usb usb2: USB disconnect, device number 1
[ 24.126503] xhci-hcd xhci-hcd.0.auto: USB bus 2 deregistered
[ 24.130347] xhci-hcd xhci-hcd.0.auto: remove, state 1
[ 24.135948] usb usb1: USB disconnect, device number 1
[ 24.142085] xhci-hcd xhci-hcd.0.auto: USB bus 1 deregistered
root@LEDE:/#
Fixes: dwc3-of-simple module unloading
Signed-off-by: Thomas Reifferscheid <thomas@reifferscheid.org>
Thomas Reifferscheid [Mon, 27 Mar 2017 21:52:06 +0000 (23:52 +0200)]
ipq8064: Fix dwc3 module unloading
Allow module unloading by fixing a mistake.
qcom_dwc3_phy_write_readback() is expecting (phy, offset, mask, value)
while the mistake was calling it with (phy, offset, value, mask)
The patch is swapping value and mask.
Without the patch unloading the dwc3 module was showing a
write to QSCRATCH failed and repeated module loading was
failing:
root@LEDE:/# rmmod dwc3
[ 19.167998] xhci-hcd xhci-hcd.1.auto: remove, state 1
[ 19.168084] usb usb4: USB disconnect, device number 1
[ 19.173371] xhci-hcd xhci-hcd.1.auto: USB bus 4 deregistered
[ 19.177134] xhci-hcd xhci-hcd.1.auto: remove, state 1
[ 19.182960] usb usb3: USB disconnect, device number 1
[ 19.189023] xhci-hcd xhci-hcd.1.auto: USB bus 3 deregistered
[ 19.192989] qcom-dwc3-usb-phy
110f8830.phy: write:
8000000 to QSCRATCH: 0 FAILED
[ 19.199064] xhci-hcd xhci-hcd.0.auto: remove, state 1
[ 19.205912] usb usb2: USB disconnect, device number 1
[ 19.211611] xhci-hcd xhci-hcd.0.auto: USB bus 2 deregistered
[ 19.215905] xhci-hcd xhci-hcd.0.auto: remove, state 1
[ 19.221751] usb usb1: USB disconnect, device number 1
[ 19.227307] xhci-hcd xhci-hcd.0.auto: USB bus 1 deregistered
[ 19.231795] qcom-dwc3-usb-phy
100f8830.phy: write:
8000000 to QSCRATCH: 0 FAILED
root@LEDE:/# modprobe dwc3
[ 29.583343] phy phy-
100f8830.phy.4: phy init failed --> -110
[ 29.583399] dwc3
10000000.dwc3: failed to initialize core
[ 29.588169] dwc3: probe of
10000000.dwc3 failed with error -110
[ 29.652943] phy phy-
110f8830.phy.2: phy init failed --> -110
[ 29.652988] dwc3
11000000.dwc3: failed to initialize core
[ 29.657735] dwc3: probe of
11000000.dwc3 failed with error -110
root@LEDE:/#
With patch repeated module unloading and loading is working good:
root@LEDE:/# rmmod dwc3
[ 22.622214] xhci-hcd xhci-hcd.1.auto: remove, state 1
[ 22.622298] usb usb4: USB disconnect, device number 1
[ 22.627401] xhci-hcd xhci-hcd.1.auto: USB bus 4 deregistered
[ 22.631492] xhci-hcd xhci-hcd.1.auto: remove, state 1
[ 22.637054] usb usb3: USB disconnect, device number 1
[ 22.643721] xhci-hcd xhci-hcd.1.auto: USB bus 3 deregistered
[ 22.647421] xhci-hcd xhci-hcd.0.auto: remove, state 1
[ 22.652910] usb usb2: USB disconnect, device number 1
[ 22.659219] xhci-hcd xhci-hcd.0.auto: USB bus 2 deregistered
[ 22.662768] xhci-hcd xhci-hcd.0.auto: remove, state 1
[ 22.668604] usb usb1: USB disconnect, device number 1
[ 22.674803] xhci-hcd xhci-hcd.0.auto: USB bus 1 deregistered
root@LEDE:/# modprobe dwc3
[ 25.404592] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller
[ 25.404694] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 1
[ 25.409444] xhci-hcd xhci-hcd.0.auto: hcc params 0x0228f065 hci version 0x100 quirks 0x00010010
[ 25.416589] xhci-hcd xhci-hcd.0.auto: irq 168, io mem 0x10000000
[ 25.426509] hub 1-0:1.0: USB hub found
[ 25.431626] hub 1-0:1.0: 1 port detected
[ 25.435472] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller
[ 25.439206] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 2
[ 25.444573] usb usb2: We don't know the algorithms for LPM for this host, disabling LPM.
[ 25.452926] hub 2-0:1.0: USB hub found
[ 25.460420] hub 2-0:1.0: 1 port detected
[ 25.525037] xhci-hcd xhci-hcd.1.auto: xHCI Host Controller
[ 25.525099] xhci-hcd xhci-hcd.1.auto: new USB bus registered, assigned bus number 3
[ 25.529750] xhci-hcd xhci-hcd.1.auto: hcc params 0x0228f065 hci version 0x100 quirks 0x00010010
[ 25.537002] xhci-hcd xhci-hcd.1.auto: irq 169, io mem 0x11000000
[ 25.546583] hub 3-0:1.0: USB hub found
[ 25.551997] hub 3-0:1.0: 1 port detected
[ 25.555734] xhci-hcd xhci-hcd.1.auto: xHCI Host Controller
[ 25.559621] xhci-hcd xhci-hcd.1.auto: new USB bus registered, assigned bus number 4
[ 25.564942] usb usb4: We don't know the algorithms for LPM for this host, disabling LPM.
[ 25.573063] hub 4-0:1.0: USB hub found
[ 25.580842] hub 4-0:1.0: 1 port detected
root@LEDE:/#
Fixes: dwc3 module unloading
Signed-off-by: Thomas Reifferscheid <thomas@reifferscheid.org>
Hannu Nyman [Thu, 23 Mar 2017 14:53:17 +0000 (16:53 +0200)]
mac80211: ath10k: allow failure getting board id via otp
ath10k tries to fetch board id via otp, but that fails for many chips
like QCA988x, QCA9984 etc. Recent commit
cc189c0b7f removed the earlier
hack that had allowed QCA radios to work, as that hack was incompatible
with the new wifi chips being introduced to the source tree.
Restore functionality for the existing wifi chips by modifying the
return value of the 'board id via otp' function to a value that is recognised
as a harmless error, so that name evaluation continues by using the board file.
Patch originally suggested by Christian Lamparter in forum discussion.
Signed-off-by: Hannu Nyman <hannu.nyman@iki.fi>
John Crispin [Fri, 24 Mar 2017 07:31:17 +0000 (08:31 +0100)]
ramips: fix pcie irq mapping for mt7621 on v4.9
Signed-off-by: John Crispin <john@phrozen.org>
Rafał Miłecki [Fri, 24 Mar 2017 17:25:23 +0000 (18:25 +0100)]
bcm53xx: put kernel into TRX when building initramfs images
Many (most?) devices can't boot raw kernel using tftp and probably none
allows flashing it. It's way more usable to have TRX with kernel
containing initrams as such an image can be actually flashed.
An exception are Buffalo devices which have recovery mode with support
for booting kernels over TFTP. For them keep building default images.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Leon M. George [Fri, 24 Mar 2017 11:18:57 +0000 (12:18 +0100)]
ar71xx: wpj531: fix GPIOs for LED
/sys/devices/platform/leds-gpio/leds/ was not initialised with working LEDs.
Signed-off-by: Leon M. George <leon@georgemail.eu>
Thomas Reifferscheid [Fri, 24 Mar 2017 23:11:43 +0000 (00:11 +0100)]
ipq8064: enable 2nd USB port on R7500
Makes use of the syscon tcsr and enables both USB ports. Cleans up
qcom-ipq8064.dtsi from previous attempts.
Fixes FS#497
Signed-off-by: Thomas Reifferscheid <thomas@reifferscheid.org>
Shane Peelar [Fri, 24 Mar 2017 15:49:45 +0000 (11:49 -0400)]
kernel: Fix F2FS module dependencies
F2FS depends on the crc32_generic module (NOT crc32c_generic)
Signed-off-by: Shane Peelar <lookatyouhacker@gmail.com>
Shane Peelar [Fri, 24 Mar 2017 14:44:24 +0000 (10:44 -0400)]
kernel: Add kmod-crypto-crc32 (crc32_generic.ko)
This is needed for F2FS support (it depends on crc32_generic,
not crc32c_generic).
Signed-off-by: Shane Peelar <lookatyouhacker@gmail.com>
Paul Wassi [Sat, 25 Mar 2017 10:46:10 +0000 (11:46 +0100)]
package/boot/uboot-kirkwood: fix build errors for nsa310 and nsa325
With upstream changes, the last update to U-Boot 2017.03
broke the nsa310 and nsa325 targets. Also fix some redefines.
Signed-off-by: Paul Wassi <p.wassi@gmx.at>
Stefan Koch [Fri, 24 Mar 2017 16:18:06 +0000 (17:18 +0100)]
lantiq: align falcon code with ar9-vr9 code
Signed-off-by: Stefan Koch <stefan.koch10@gmail.com>
Stefan Koch [Fri, 24 Mar 2017 16:08:59 +0000 (17:08 +0100)]
lantiq: cleanup code ar9-vr9 parts
- remove unused code within 500-ar9_vr9.patch
- fixed return of IFX_ERROR (solves SIGSEGV in asterisk at failure)
- align it a bit with 400-falcon.patch
- remove 600-kernel-4.9.patch since changed parts
are removed during cleanup
Signed-off-by: Stefan Koch <stefan.koch10@gmail.com>
Pavel Kubelun [Fri, 24 Mar 2017 13:12:40 +0000 (16:12 +0300)]
ipq806x: tsens: convert degrees to millicelsius
Current driver shows temp in full degrees while other apps await it
to be in millidegrees.
Initially the driver represents termal data in millidegrees but then
it gets divided by TSENS_FACTOR. So lets just set it to '1'.
Signed-off-by: Pavel Kubelun <be.dissent@gmail.com>
Pavel Kubelun [Thu, 23 Mar 2017 14:59:30 +0000 (17:59 +0300)]
ipq806x: add ipq806x specific tsens driver
Current upstream driver doesnt fully support ipq806x devices
ipq806x has 11 sensors, the upstream one doesn't allow to check
sensors 0-4, only 5-10.
A specific driver for ipq806x has been found in Qualcomm SDK repo.
https://source.codeaurora.org/quic/qsdk/oss/kernel/linux-msm/commit/?h=release/endive_preview_cc&id=
c089e464cd7ce652419a0dc44d7959ce4d24b8a5
https://source.codeaurora.org/quic/qsdk/oss/kernel/linux-msm/commit/?h=release/endive_preview_cc&id=
c23d94b702c4182862e7f5051a2b7d00bb922a29
https://source.codeaurora.org/quic/qsdk/oss/kernel/linux-msm/commit/?h=release/endive_preview_cc&id=
742f3684b62a6b9f082cb49404b1a92dc0b16bf5
https://source.codeaurora.org/quic/qsdk/oss/kernel/linux-msm/commit/?h=release/endive_preview_cc&id=
c0a9b2e2a382c152fa128f5b864c800dd6dfb311
Merging it into LEDE with this commit.
Signed-off-by: Pavel Kubelun <be.dissent@gmail.com>
Hauke Mehrtens [Sun, 26 Mar 2017 17:20:33 +0000 (19:20 +0200)]
kernel: add arm64 erratums into config
Deactivate all the ARM64 erratums by default. The target code should
activate them if needed. This fixes a problem with a new erratum added
in kernel 4.9.17 breaking brcm2708.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Hauke Mehrtens [Sun, 12 Feb 2017 22:48:11 +0000 (23:48 +0100)]
lantiq: update spi driver to upstream version
These patches are backported from upstream Linux kernel.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Hauke Mehrtens [Sun, 26 Mar 2017 10:22:27 +0000 (12:22 +0200)]
kernel: update kernel 4.9 to 4.9.17
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Hauke Mehrtens [Sun, 26 Mar 2017 10:01:22 +0000 (12:01 +0200)]
kernel: update kernel 4.4 to 4.4.56
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Matthias Schiffer [Sat, 25 Mar 2017 12:43:29 +0000 (13:43 +0100)]
iw: enable MESH ID in scan output
Make scan output useful for 802.11s meshes. The common print_ssid function
is used, so this doesn't add any additional code.
Based-on-patch-by: Jan-Tarek Butt <tarek@ring0.de>
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
Yousong Zhou [Sat, 25 Mar 2017 04:16:36 +0000 (12:16 +0800)]
busybox: vi: backporting patches to fix ZZ and :x command
Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
Rafał Miłecki [Wed, 22 Mar 2017 22:35:39 +0000 (23:35 +0100)]
brcm2708: backport upstream ARM dts commits
This gets us in sync with dts from kernel 4.11. Two patches were already
backported earlier.
I decided to use 03x prefix as it's kind of similar to the 3xx prefix:
3xx - architecture specific patches
It isn't any documented or strict rule though. We don't need to stick to
it if we hit any problems.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Acked-by: Álvaro Fernández Rojas <noltari@gmail.com>
Stefan Koch [Wed, 22 Mar 2017 11:05:54 +0000 (12:05 +0100)]
lantiq: vr9 fxs support: remove unused wdog declarations and initializers
modify 0152-lantiq-VPE.patch from
commit
e0229a16b000 ("lantiq: added support for VPE1")
- remove wdog function declarations from header (asm/vpe.h)
- remove wdog command line init functions (vpe.c)
Signed-off-by: Stefan Koch <stefan.koch10@gmail.com>
Stefan Koch [Tue, 21 Mar 2017 16:21:58 +0000 (17:21 +0100)]
lantiq: vr9 fxs support: remove soft-watchdog functionality
- remove patched header (vpe.h) because kernel
already provides one (asm/vpe.h)
- remove module softdog_vpe since watchdog functionality is unused
- remove module softdog_vpe from Makefile
Signed-off-by: Stefan Koch <stefan.koch10@gmail.com>
Stefan Koch [Tue, 21 Mar 2017 16:21:17 +0000 (17:21 +0100)]
lantiq: remove residual watchdog parts from ltq-vmmc
modify 500-ar9_vr9.patch from
commit
29367aac42d6 ("lantiq: ltq-vmmc add support for ar9-vr9")
- remove unused dependencies to external watchdog functions
(wdog setup is already disabled)
- using header file from kernel (asm/vpe.h) instead patched file (vpe.h)
- cleanup whitspace warning
Signed-off-by: Stefan Koch <stefan.koch10@gmail.com>
Mathias Kresin [Thu, 23 Mar 2017 19:30:25 +0000 (20:30 +0100)]
ramips: fix Xiaomi MiWiFi Nano firmware partition size
Even the commit message of the patch adding support for the MiWiFi Nano
says that a 16 MB flash chip is used. Extend the firmware partition to
make use of all available flash space.
Fixes: FS#622
Signed-off-by: Mathias Kresin <dev@kresin.me>
Mathias Kresin [Fri, 17 Mar 2017 18:54:55 +0000 (19:54 +0100)]
ath10k-firmware: do not select the qca988x by default
Do not select the qca988x by default as soon as kmod-ath10k is
selected. We do support more ath10k chips than the qca988x in the
meantime, so this dependency doesn't make sense any longer.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Mathias Kresin [Fri, 17 Mar 2017 18:36:06 +0000 (19:36 +0100)]
treewide: select ath10k firmware explicit
Do not rely on the default firmware selected by ath10k.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Thomas Reifferscheid [Fri, 17 Mar 2017 13:01:34 +0000 (14:01 +0100)]
ipq806x: fix Netgear X4 R7500 ath10k firmware selection
Netgear X4 R7500 comes with a QCA988X. Select a firmware that matches
the ath10k chipset
Signed-off-by: Thomas Reifferscheid <thomas@reifferscheid.org>
Mathias Kresin [Fri, 10 Mar 2017 21:46:30 +0000 (22:46 +0100)]
lantiq: fix pci with kernel 4.9
Commit
23dac14d058f ("MIPS: PCI: Use struct list_head lists") changed
the controller list from reverse to straight order. Use the last entry
in the controller list to get the fist conroller of the system.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Mathias Kresin [Fri, 17 Mar 2017 06:29:16 +0000 (07:29 +0100)]
kernel: add MIPS pci fix send upstream
Upstream commit
23dac14d058f ("MIPS: PCI: Use struct list_head lists")
changed the controller list from reverse to straight order without
taking care of the changed order for the scan of the recorded PCI
controllers.
Traverse the list in reverse order to restore the former behaviour.
This patches fixes the following PCI error on lantiq:
pci 0000:01:00.0: BAR 0: error updating (0x1c000004 != 0x000000)
Signed-off-by: Mathias Kresin <dev@kresin.me>
Rafał Miłecki [Wed, 22 Mar 2017 20:09:00 +0000 (21:09 +0100)]
brcm2708: rename all patches from raspberrypi git tree to use 950 prefix
Right now all brcm2708 patches are extracted from the non-mainline
raspberrypi/linux git tree. Many of them are hacks and/or are unneeded
in LEDE. Raspberry Pi is getting better and better mainline support so
it would be nice to finally start maintaining patches in a cleaner way:
1) Backport patches accepted in upstream tree
2) Start using upstream drivers
3) Pick only these patches that are needed for more complete support
Handling above tasks requires grouping patches - ideally using the same
prefixes as generic ones. It means we should rename existing patches to
use some high prefix. This will allow e.g. use 0xx for backported code.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Stijn Tintel <stijn@linux-ipv6.be>
Yousong Zhou [Fri, 24 Mar 2017 02:37:08 +0000 (10:37 +0800)]
gdb: fix invalid sigprocmask call
Fixes FS#637
Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
Piotr Dymacz [Wed, 22 Mar 2017 19:36:22 +0000 (20:36 +0100)]
ar71xx: image: fix indentation
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
Piotr Dymacz [Wed, 15 Mar 2017 23:54:08 +0000 (00:54 +0100)]
ar71xx: add support for P&W R602N and CPE505N
P&W (full name: Shenzhen Progress&Win Technologies) R602N (could be also
labeled as R602F, R602, etc.) is a simple N300 router with 5-port
10/100 Mbps switch, non-detachable antennas and USB.
CPE505 is an outdoor CPE with PoE support and detachable antennas.
Both devices are based on Qualcomm/Atheros QCA9531 v2.
Common specification:
- 650/597/216 MHz (CPU/DDR/AHB)
- 64 MB of RAM (DDR2)
- 16 MB of FLASH
- UART (J2) header on PCB
R602N specification:
- 5x 10/100 Mbps Ethernet
- 1x USB 2.0
- 2T2R 2.4 GHz with external LNA and PA (SE2576L), up to 28 dBm
- 2x external, non-detachable antennas
- 7x LED, 1x button
CPE505N specification:
- 2x 10/100 Mbps Ethernet (both ports support passive PoE 12-24 V)
- 2T2R 2.4 GHz with external LNA and PA (SKY65174-21), up to 30 dBm
- 2x external, detachable antennas (RP-SMA connectors)
- 1x RGB LED, 2x LEDs (in RJ45 sockets), 1x button
Flash instructions:
It seems that there are many different versions of the firmware which
these devices are shipped with. The generic/standard one is based on
some modified OpenWrt and LEDE firmware can be flashed directly from
vendor's webgui or with sysupgrade (root password is "admin123").
Before flashing, make sure (use "fw_printenv") that the kernel load
address in your device is set to "0x9f050000" (bootcmd variable is
"bootm 0x9f050000"). If your device uses different load address, you
should first change it, under vendor's firmware, with command:
fw_setenv bootcmd "bootm 0x9f050000 || bootm OLD_ADDRESS"
Where OLD_ADDRESS is previous kernel load address (in CPE505 version
I got access to, it was "0x9fe80000"). This will allow you to use
both the vendor's and LEDE firmware.
If version of your device contains empty U-Boot environment (you will
get information about this after issuing "fw_printenv"), you should
use U-Boot, serial line access and TFTP to perform firmware upgrade:
1. tftp 0x80060000 lede-ar71xx-generic-...-squashfs-sysupgrade.bin
2. erase 0x9f050000 +$filesize
3. cp.b $fileaddr 0x9f050000 $filesize
4. setenv bootcmd "bootm 0x9f050000 || bootm OLD_ADDRESS"
5. saveenv && reset
These devices contain also web recovery mode inside U-Boot. It can be
started with pressing the reset button for around 3 seconds just after
the device powerup. Web recovery panel is available on "192.168.10.9"
and to be able to use it, IP on your PC must be set to "192.168.10.10".
Make sure to change kernel load address before using recovery mode or
the U-Boot will not be able to load LEDE firmware.
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
Vaclav Svoboda [Thu, 16 Mar 2017 00:43:43 +0000 (01:43 +0100)]
ar71xx: add support for TP-LINK TL-WR840N v2 and v3
This patch adds support for the TP-LINK TL-WR840N v2 and v3.
- SoC: Qualcomm QCA9533-BL3A (650 MHz)
- RAM: 32 MiB (Zentel A3S56D40GTP)
- Flash: 4 MiB
(v2: Macronix MX 25L323F)
(v3: Winbond 25Q32FVSIG)
- LAN: 4x 100M
- WAN: 1x 100M
Signed-off-by: Vaclav Svoboda <svoboda@neng.cz>
Ryan Mounce [Fri, 17 Mar 2017 04:00:33 +0000 (14:30 +1030)]
ar71xx: add support for MikroTik hAP ac
This patch adds initial support for the MikroTik RouterBOARD hAP ac
(RB962UiGS-5HacT2HnT).
All functions are supported except:
-SFP cage (eth1) is not working
-WLAN LEDs are not working
Signed-off-by: Ryan Mounce <ryan@mounce.com.au>
Ryan Mounce [Wed, 8 Mar 2017 09:07:00 +0000 (19:37 +1030)]
ar71xx: add support for MikroTik hAP ac lite
This patch adds support for the MikroTik RouterBOARD hAP ac lite
(RB952Ui-5ac2nD).
The hAP ac lite is nearly identical to the hAP, with an added QCA9887
5GHz radio. The 2.4GHz radio ID is also changed in the hAP ac lite.
Signed-off-by: Ryan Mounce <ryan@mounce.com.au>
John Crispin [Thu, 23 Mar 2017 08:18:42 +0000 (09:18 +0100)]
ramips: fix mt7621 boot on v4.9
v4.9 CM code has a few bugs on this HW. Disable the GCR register access
during boot. This caused a cpu stall.
Signed-off-by: John Crispin <john@phrozen.org>
John Crispin [Thu, 23 Mar 2017 07:29:21 +0000 (08:29 +0100)]
Revert "ipq806x: make the dwc3 driver and required phy drivers built-in"
This reverts commit
d5b10bb560c2c3c615babfcfb64519bfc65818d9.
This caused boot errors on some ipq8 boards
Signed-off-by: John Crispin <john@phrozen.org>
Hans Dedecker [Wed, 22 Mar 2017 20:56:05 +0000 (21:56 +0100)]
odhcp6c: update to git HEAD version
0463b05 dhcpv6: rebind capability support in reconfigure message (rfc6644)
53767fc dhcpv6: respect renew end point when handling reconfigure message
dd892e2 dhcpv6: calculate T1, T2 and T3 in a more sane manner
8a6ca6e md5: use libubox md5 library as local implementation
89822de dhcpv6: don't return renew msg in case of invalid msg type in reconfigure msg
4160c0e treewide: align coding style
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
Felix Fietkau [Wed, 22 Mar 2017 19:46:14 +0000 (20:46 +0100)]
ath9k: fix power limits on init
The tx power applied by set_txpower is limited by the CTL (conformance
test limit) entries in the EEPROM. These can change based on the user
configured regulatory domain.
Depending on the EEPROM data this can cause the tx power to become too
limited, if the original regdomain CTLs impose lowr limits than the CTLs
of the user configured regdomain.
To fix this issue, set the initial channel limits without any CTL
restrictions and only apply the CTL at run time when setting the channel
and the real tx power.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Felix Fietkau [Wed, 22 Mar 2017 19:24:32 +0000 (20:24 +0100)]
ath: do not apply broken power limits with ATH_USER_REGD
If a device uses the default EEPROM code, typically only the main CTLs
are valid, and they do not apply properly when switching to a different
regulatory domain. If the regdomain deviates from the EEPROM one, force
the world roaming regdomain to ensure that power limits are sane
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Felix Fietkau [Wed, 22 Mar 2017 19:16:15 +0000 (20:16 +0100)]
build: fix STAMP_PREPARED with quilt
quilt.mk needs to be included first, to ensure that STAMP_PREPARED does
not include the hash if quilt is used.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Felix Fietkau [Wed, 22 Mar 2017 12:22:57 +0000 (13:22 +0100)]
util-linux: re-enable parallel builds
The original build error in 'more' seems to be gone
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Felix Fietkau [Wed, 22 Mar 2017 12:49:05 +0000 (13:49 +0100)]
util-linux: unconditionally enable ncursesw support
The build dependency is unconditional, and some components might fail if
ncurses is not available
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Daniel Engberg [Mon, 20 Mar 2017 08:51:26 +0000 (09:51 +0100)]
utils/util-linux: Update to 2.29.2
Update util-linux to 2.29.2
Remote 0001-fix-uClibc-ng-scanf-check.patch as it's been merged upstream.
Refresh patches
Change ncurses to ncursesw to fix compilation and avoid confusion
Signed-off-by: Daniel Engberg <daniel.engberg.lists@pyret.net>
Signed-off-by: Felix Fietkau <nbd@nbd.name> [remove faulty dependency changes]
Rafał Miłecki [Wed, 22 Mar 2017 13:22:07 +0000 (14:22 +0100)]
kernel: disable DRM_HISI_KIRIN and USB_DWC3_OF_SIMPLE
They were triggering config prompts on brcm2710.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Rafał Miłecki [Wed, 22 Mar 2017 11:22:33 +0000 (12:22 +0100)]
kernel: fix builds with kmod-drm-vc4 and CONFIG_SPI enabled
This fixes:
Samsung LD9040 RGB/SPI panel (DRM_PANEL_SAMSUNG_LD9040) [N/m] (NEW) aborted!
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
John Crispin [Wed, 22 Mar 2017 11:13:12 +0000 (12:13 +0100)]
Revert "utils/util-linux: Update to 2.29.2"
This reverts commit
eac1a548573a0262e9f36aeee95ed071f6040703.
This patch caused the builders to blow up.
Signed-off-by: John Crispin <john@phrozen.org>
Daniel Engberg [Wed, 15 Mar 2017 16:14:55 +0000 (17:14 +0100)]
utils/f2fs-tools: Update to 1.8.0
Update f2fs-tools to 1.8.0
Refresh patches
Remove selinux patch, use configure argument instead.
Switch to xz tarball
Adjust url to avoid redirects
Signed-off-by: Daniel Engberg <daniel.engberg.lists@pyret.net>
Felix Fietkau [Mon, 6 Mar 2017 09:12:50 +0000 (10:12 +0100)]
x86: enable ACPI support for the Geode subtarget
Most or all newer Geode device have ACPI hardware support
Should fix FS#577
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Felix Fietkau [Fri, 17 Mar 2017 16:02:55 +0000 (17:02 +0100)]
pistachio: remove custom board detection override
Use device tree based model string
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Felix Fietkau [Fri, 17 Mar 2017 16:00:39 +0000 (17:00 +0100)]
pistachio: fix indentation in image makefile
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Felix Fietkau [Fri, 17 Mar 2017 15:56:40 +0000 (16:56 +0100)]
pistachio: remove pistachio_board_name, use the generic function
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Ian Pozella [Thu, 2 Feb 2017 09:42:04 +0000 (09:42 +0000)]
target: add pistachio
The Pistachio target is a MIPS interaptiv based SoC developed by
Imagination Technologies. It includes blocks for i2c, spi, audio,
usb and WiFi.
This also adds the base support for the 'Creator Ci40 (marduk)'
device which uses the Pistachio SoC to create an IoT hub by
including Bluetooth, WiFi and 6lowpan on one board. Additionally 2x
Mikrobus ports are available to expand with further RF technologies
or add sensors. You can find out more here http://creatordev.io.
Note, this commit is just the initial board support hence the
following are not expected to work yet:
* WiFi
* Bluetooth
* 6lowpan
* Audio
* Mikrobus uarts, user leds (clock dependency of 6lowpan chip)
The aim of this commit is to essentially have the same level of
support that currently exists in the mainline kernel.
Signed-off-by: Abhijit Mahajani <Abhijit.Mahajani@imgtec.com>
Signed-off-by: Francois Berder <francois.berder@imgtec.com>
Signed-off-by: Ian Pozella <Ian.Pozella@imgtec.com>
Signed-off-by: Mayank Sirotiya <Mayank.Sirotiya@imgtec.com>
Signed-off-by: Sean Kelly <Sean.Kelly@imgtec.com>
Ian Pozella [Wed, 15 Feb 2017 09:05:24 +0000 (09:05 +0000)]
pistachio: add 4.9 kernel support
This adds kernel support for the Pistachio SoC and the Marduk (Ci40)
board which uses it.
Much of the code for Pistachio has been upstreamed however some
patches are still required to boot from the Marduk board:
* spi bug fixes
* dma bug fixes
* pistachio internal clock tree bug fixes
* spi-nand implementation
* dts based mtd device naming scheme
* dts backports and bug fixes
Signed-off-by: Abhijit Mahajani <Abhijit.Mahajani@imgtec.com>
Signed-off-by: Francois Berder <francois.berder@imgtec.com>
Signed-off-by: Ian Pozella <Ian.Pozella@imgtec.com>
Felix Fietkau [Fri, 17 Mar 2017 19:37:52 +0000 (20:37 +0100)]
kernel: do not try to copy vmlinux out of arch/$(ARCH)/boot
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Felix Fietkau [Fri, 17 Mar 2017 15:21:49 +0000 (16:21 +0100)]
lantiq: remove lantiq_board_model, it is unused
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Felix Fietkau [Fri, 17 Mar 2017 15:21:30 +0000 (16:21 +0100)]
lantiq: remove lantiq_board_name, use the generic function instead
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Felix Fietkau [Fri, 17 Mar 2017 15:17:42 +0000 (16:17 +0100)]
lantiq: move lantiq_board_detect() to 03_preinit_board.sh
It is only used there
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Felix Fietkau [Fri, 17 Mar 2017 15:12:27 +0000 (16:12 +0100)]
base-files: add generic board_name function to functions.sh
This will be used to replace all those nasty board specific scripts
that do basically the same thing
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Felix Fietkau [Thu, 16 Mar 2017 15:54:16 +0000 (16:54 +0100)]
busybox: enable the "ip neigh" command (FS#618)
It is useful for creating static ARP entries.
Adds about 1.9 KiB after gzip on MIPS.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Vittorio Gambaletta [Tue, 14 Mar 2017 13:45:15 +0000 (14:45 +0100)]
mac80211: Fix race condition leading to wifi interfaces not coming up at boot sometimes.
In the drv_mac80211_setup function, mac80211_interface_cleanup
is called to ask the kernel to delete all existing interfaces
for the phy that is being configured via netlink.
Later in the first function, mac80211_prepare_vif is called to
set up the new interfaces as required.
But sometimes, when mac80211_prepare_vif (and so the relevant
`iw phy x interface add y` command) runs, the kernel might still
be cleaning up the old interface with the same ifname. It usually
takes very few time to do that; possibly a few milliseconds of
sleep in the script after detecting this error condition could be
enough, but the busybox sh does not support sub-second sleep
intervals.
When this happens, iw obviously fails to create the new interface;
and the following message is printed in the system log, followed by
subsequent failure messages from hostapd in case this would have been
an AP interface.
Tue Mar 14 04:21:57 2017 daemon.notice netifd: radio1 (2767): command failed: Too many open files in system (-23)
This was a long-standing issue existing since at least OpenWrt Backfire,
and today I finally managed to debug and (hopefully) solve it.
It was happening very few times on most devices; but it was happening
a lot more frequently on fast platforms with multiple radios, such as
the powerpc-based dual-ath9k-radio tl-wdr4900-v1.
Signed-off-by: Vittorio Gambaletta <openwrt@vittgam.net>
John Crispin [Wed, 22 Mar 2017 08:43:01 +0000 (09:43 +0100)]
ipq806x: remove v4.4 support
Signed-off-by: John Crispin <john@phrozen.org>
John Crispin [Wed, 15 Mar 2017 10:49:43 +0000 (11:49 +0100)]
ipq806x: set v4.9 as default
Signed-off-by: John Crispin <john@phrozen.org>
Christian Lamparter [Wed, 15 Mar 2017 10:49:14 +0000 (11:49 +0100)]
firmware: add custom IPQ wifi board definitions
On the ath10k-devel ML Michael Kazior stated:
"board-2 is a key-value store of actual board files.
Some devices, notably qca61x4 hw3+ and qca4019 need
distinct board files to be uploaded. Otherwise they
fail in various ways." [0].
Later on Rajkumar Manoharan explained:
"In QCA4019 platform, only radio specific calibration
(pre-cal-data) is stored in flash. Board specific contents
are read from board-2.bin. For each radio appropriate board
data should be loaded. To fetch correct board data from
board-2.bin bundle, pre-cal/radio specific caldata should
be loaded first to get proper board id.
|My understanding until now was that:
|
| * pre-cal data + board-2.bin info == actual calibration data
Correct." [1].
The standard board-2.bin from the ath10k-firmware-qca4019
barely works on the RT-AC58U. Especially 5GHz clients fail
to connect at all and if they do, they have very low
throughput even right next to the router.
Currently, the solution for this problem is to supply a
custom board-2.bin for every device.
To implement this feature, this method makes use of:
Rafał Miłecki's "base-files: add support for overlaying
rootfs content". This comes with a few limitations:
1. Since there can only be one board-2.bin at the right
location, there can only one board overwrite installed
at any time. (All packages CONFLICT with each other.
It's also not possible to "builtin" multiple package.)
2. updating ath10k-firmware-qca4019 will also replace
the board-2.bin. For this cases the user needs to
manually reinstall the wifi-board package once the
ath10k-firmware-qca4019 is updated.
To create the individual board-2.bin: Use the ath10k-bdencoder
utility from the qca-swiss-army-knife repository:
<https://github.com/qca/qca-swiss-army-knife>
The raw board.bin files have to be extracted from the
vendor's source GPL.tar archieves.
Signed-off-by: Alexis Green <agreen@cococorp.com>
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Christian Lamparter [Wed, 15 Mar 2017 10:48:56 +0000 (11:48 +0100)]
firmware: add IPQ fritz-tools FW extraction tool
Adds tools to access tffs3 and pre-calibration data required for ipq4019
based FritBoxes.
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
John Crispin [Wed, 22 Mar 2017 08:36:00 +0000 (09:36 +0100)]
ipq806x: make the dwc3 driver and required phy drivers built-in
Signed-off-by: John Crispin <john@phrozen.org>
John Crispin [Wed, 22 Mar 2017 08:29:11 +0000 (09:29 +0100)]
ipq806x: enable QCE hardware crypto inside the kernel
Signed-off-by: John Crispin <john@phrozen.org>
Christian Lamparter [Tue, 14 Mar 2017 16:04:28 +0000 (17:04 +0100)]
ipq806x: add ipq4019 fritz4040 support
This patch adds support for AVM FRITZ!Box 4040.
hardware highlights:
SOC: IPQ4018 / QCA Dakota
CPU: Quad-Core ARMv7 Processor rev 5 (v7l) Cortex-A7
DRAM: 256 MiB Nanya NT5CC128M16IP
FLASH: 32 MiB MXIC MX25L25635FMI
ETH: Qualcomm Atheros QCA8075 Gigabit Switch (4 x LAN, 1 x WAN)
USB: 1 x 3.0 (via Synopsys DesignWare DWC3 controller in the SoC)
1 x 2.0 (via Synopsys DesignWare DWC3 controller in the SoC)
WLAN1: Qualcomm Atheros QCA4018 2.4GHz 802.11bgn 2:2x2
WLAN2: Qualcomm Atheros QCA4018 5GHz 802.11a/n/ac 2:2x2
INPUT: one WLAN and one WPS button
LEDS: Power, WAN/Internet, WIFI, INFO (red and amber) and LAN.
Serial:
WARNING: The serial port needs a TTL/RS-232 v3.3 level converter!
The Serial setting is 115200-8-N-1. The SoC's serial port is right
next to the MXIC FLASH chip. The board has a unpopulated 1x4 0.1"
header for it. Use a multimeter to figure out the pinout!
This board currently needs an additional u-boot image in order to boot
properly. Booting with EVA isn't possible ATM.
Install Procedure:
0. It's highly recommended to connect to the serial port.
The serial settings are listed above.
1. install a u-boot image for AVM Fritz!Box 4040
(see <https://github.com/chunkeey/FritzBox-4040-UBOOT/releases> and
<https://github.com/chunkeey/FritzBox-4040-UBOOT/blob/master/upload-to-f4040.sh>)
2. upload the initramfs.itb image via tftp (u-boot listens to
192.168.1.1 - use binary transfer mode!)
3. connect to the FB4040 and use sysupgrade sysupgrade.bin
to install the image.
Works:
- Switch and Ethernet (99%)
- Buttons (WLAN, WPS)
- FLASH (1 x 32MiB NOR Chip)
- WLAN2G and WLAN5G
- CPUFREQ scaling
- PRNG
- serial
- Crypto Accelerator
- sysupgrade (Read the flash instructions to avoid bricking)
- full LEDE Install (Read the flash instructions to avoid bricking)
- LEDs (Power, WAN, Info (red and amber), LAN)
The LEDs are connected to the QCA8075 LED ports.
The AR40xx driver contains a gpio-controller to
handle these special "GPIOs".
- USB Both 3.0 and 2.0 ports
- many packages from other ARMv7 boards
(This does include the RaspberryPi Model 2!)
- ...
Not planned:
- WAN<->LAN short-cut
- Qualcomm Secure Execution Environment
- ...
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John Crispin <john@phrozen.org>
Christian Lamparter [Tue, 14 Mar 2017 16:02:20 +0000 (17:02 +0100)]
ipq806x: add ipq4019 support
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John Crispin <john@phrozen.org>
Felix Fietkau [Tue, 14 Mar 2017 09:19:17 +0000 (10:19 +0100)]
uboot-fritz4040: add an ipq806x u-boot for FritzBox 4040
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Christian Lamparter [Sun, 20 Nov 2016 02:33:03 +0000 (03:33 +0100)]
procd: nand: make it possible to configure kernel and ubi partition
With this patch, the nand.sh script no longer overwrites
CI_KERNELPART and CI_UBIPART if they have been set before.
This allows platforms specify alternative values for these
variables.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Christian Lamparter [Mon, 14 Nov 2016 03:57:38 +0000 (04:57 +0100)]
mac80211: enable ath10k AHB support for QCA4019
This patch enables the ATH10K_AHB support for the QCA4019
devices on the AHB bus.
This patch also removes 936-ath10k_skip_otp_check.patch
because it breaks the AHB device identification.
"Patch is wrong. I find it frustrating OpenWRT/LEDE doesn't
try to work with upstream on ixing these things right."
[1] <https://www.mail-archive.com/ath10k@lists.infradead.org/msg05896.html>
It also limits ath10k memory hunger (This is a problem with 128MiB RAM)
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
projects / openwrt / staging / chunkeey.git / log