drm/i915/icl: Fix DSS_CTL register names

This patch fixes the naming of the registers:

s/PIPE_DSS_CTL/ICL_PIPE_DSS_CTL

And also fix the hex values to lower case, to match
rest of the definitions.

Manasi noticed this with the patch that was merged.

v2: fix "Fixes" tag.

Fixes: 8b1b558d690a ("drm/i915/icl: Add DSS_CTL Registers")
Suggested-by: Manasi Navare <manasi.d.navare@intel.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Manasi Navare <manasi.d.navare@intel.com>
Signed-off-by: Anusha Srivatsa <anusha.srivatsa@intel.com>
Reviewed-by: Manasi Navare <manasi.d.navare@intel.com>
Signed-off-by: Manasi Navare <manasi.d.navare@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181101214216.8958-1-anusha.srivatsa@intel.com

drm/i915/icl+: Sanitize port to PLL mapping

BIOS can leave the PLL to port mapping enabled, even if the
corresponding encoder is disabled. Disable the port mapping in this
case.

Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: José Roberto de Souza <jose.souza@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181101140427.31026-9-imre.deak@intel.com

drm/i915: Configure AUX_CH_CTL when enabling the AUX power domain

Most of the AUX_CH_CTL flags are concerned with DP AUX transfer
parameters. As opposed to this the flag specifying the thunderbolt vs.
non-thunderbolt mode of the port is not related to AUX transfers at all
(rather it's repurposed to enable either TBT or non-TBT PHY HW blocks).
The programming has to be done before enabling the corresponding AUX
power well, so make it part of the power well code.

v3:
- Use existing enable/disable helpers instead of opencoding. (Jose)
- Fix type of is_tc_tbt to remain a bitfield. (Lucas)
- Add comment describing the is_tc_tbt power well flag. (Lucas)

Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=108548
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: José Roberto de Souza <jose.souza@intel.com>
Cc: Lucas De Marchi <lucas.demarchi@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181101140427.31026-8-imre.deak@intel.com

drm/i915: Enable AUX power for HDMI DDI/TypeC main link too

DDI/TypeC ports need the AUX power domain for main link functionality
even when they operate in HDMI static mode, so enable the power domain
for these ports too.

v4:
- Rebase on the upstream ICL pre_pll_enable change.

Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: José Roberto de Souza <jose.souza@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Manasi Navare <manasi.d.navare@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181101140427.31026-7-imre.deak@intel.com

drm/i915: Enable AUX power earlier

For DDI/TypeC ports the AUX power domain needs to be enabled before the
port's PLL is enabled, so move the enabling earlier accordingly.

v2:
- Preserve the pre_pll hook for GEN9_LP. (Ville)
v3:
- Add related BSpec entries to commit log. (Jose)
v4:
- Rebase on the upstream ICL pre_pll_enable change.

BSpec: 21750, 22243
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: José Roberto de Souza <jose.souza@intel.com>
Cc: Manasi Navare <manasi.d.navare@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181101140427.31026-6-imre.deak@intel.com

drm/i915: Use a helper to get the aux power domain

From ICL onwards the AUX power domain may change dynamically based on
whether a DDI/TypeC port is in thunderbolt or non-thunderbolt mode, so
use a helper function instead of a static field to get the current
domain.

Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: José Roberto de Souza <jose.souza@intel.com>
Cc: Lucas De Marchi <lucas.demarchi@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181101140427.31026-5-imre.deak@intel.com

drm/i915: Init aux_ch for HDMI ports too

From ICL onwards DDI/TypeC ports - even in HDMI static mode - need to know
which AUX CH belongs to them, so initialize aux_ch for those ports too.
For consistency do this for all HDMI ports, not only for DDI/TypeC ones.

Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: José Roberto de Souza <jose.souza@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181101140427.31026-4-imre.deak@intel.com

drm/i915: Move aux_ch to intel_digital_port

From ICL onwards all DDI/TypeC ports - even working in HDMI mode - need
to know their corresponding AUX CH, so move the field to a common
struct.

No functional change.

v3:
- Add code comment about which ports aux_ch is used for. (Jose)

Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: José Roberto de Souza <jose.souza@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181101140427.31026-3-imre.deak@intel.com

drm/i915: Move intel_aux_ch() to intel_bios.c

From ICL onwards all the DDI/TypeC ports - even working in HDMI mode -
need to know their corresponding AUX channel, so move the corresponding
helper to a common place.

No functional change.

v4:
- Fix 'no space is necessary after a cast' checkpatch warn.

Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: José Roberto de Souza <jose.souza@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181101140427.31026-2-imre.deak@intel.com

drm/i915/icl: WaAllowUMDToModifySamplerMode

Required for Bindless samplers.
Userspace consumer: mesa

V2: Rebase
V3: Update commit message

Cc: Anusha Srivatsa <anusha.srivatsa@intel.com>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Signed-off-by: Oscar Mateo <oscar.mateo@intel.com>
Signed-off-by: Radhakrishna Sripada <radhakrishna.sripada@intel.com>
Reviewed-by: Anusha Srivatsa <anusha.srivatsa@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181030084504.21537-4-radhakrishna.sripada@intel.com

drm/i915/icl: WaAllowUMDToModifyHalfSliceChicken7

Required to dinamically set 'Trilinear Filter Quality Mode'
Userpsace consumer is mesa.

V2: Rebase
V3: Update commit message

Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Cc: Anusha Srivatsa <anusha.srivatsa@intel.com>
Signed-off-by: Oscar Mateo <oscar.mateo@intel.com>
Signed-off-by: Radhakrishna Sripada <radhakrishna.sripada@intel.com>
Reviewed-by: Anusha Srivatsa <anusha.srivatsa@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181030084504.21537-3-radhakrishna.sripada@intel.com

drm/i915/icl: Implement Display WA_1405510057

Display WA_1405510057 asks to not enable YUV 420 HDMI
10bpc when horizontal blank size mod 8 reminder is 2.

V2: Rebase(r-b: Anusha)
V3: crtc_state->s/ycbcr420/output_format/

Cc: Anusha Srivatsa <anusha.srivatsa@intel.com>
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Radhakrishna Sripada <radhakrishna.sripada@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181030084504.21537-2-radhakrishna.sripada@intel.com

drm/i915/icl: Add WaEnable32PlaneMode

Gen11 Display suports 32 planes in total. Enable the new format in context
status to be used and expanded to 32 planes.

V2: Move the WA to display WA's(Chris)

Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Michel Thierry <michel.thierry@intel.com>
Cc: James Ausmus <james.ausmus@intel.com>
Reviewed-by: Anusha Srivatsa <anusha.srivatsa@intel.com>
Signed-off-by: Radhakrishna Sripada <radhakrishna.sripada@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181030084504.21537-1-radhakrishna.sripada@intel.com

drm/i915: Remove CNL from WA 827

CNL A stepping was the only affected there.
But also it is time to clean old pre-production
CNL Workarounds, so let's just remove and clean
this W/A.

Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Clint Taylor <Clinton.A.Taylor@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181031162845.12419-4-rodrigo.vivi@intel.com

drm/i915: Define WA 0870 and kill dead code.

Let's introduce the WA number that is the
cause of having NV12 disabled on both SLK and BXT.

According to Spec:

WA 0870: "Display flickers with NV12 video playback in
Y tiling mode.
WA: Use YUV422 surface format instead of NV12."

v2: remove the useless dead code and consequently
    avoiding device info flag. (Ville)

Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181031162845.12419-3-rodrigo.vivi@intel.com

drm/i915: Kill WA 0826

According to BSpec this is not needed anymore:

"This workaround is no longer needed since NV12
support is dropped for the affected projects.
"

Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181031162845.12419-2-rodrigo.vivi@intel.com

drm/i915: Kill WA 0528

First of all I believe this WA as written here was wrong.

Because it is listed on BSpec only for SKL and BXT, exactly
the only 2 platforms skipped here.

But also it is written there that we don't need this WA
anymore:
"This workaround is no longer needed since NV12 support is
dropped for the affected projects in #0870."

SO, let's kill it.

Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Vidya Srinivas <vidya.srinivas@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181031162845.12419-1-rodrigo.vivi@intel.com

drm/i915/icl: Fix DC9 Suspend for ICL.

Add missing block that takes care of inline intel_suspend_complete
for DC9 on ICL.

Daniele noticed this was part of original patch but missed on
on merged commit ("drm/i915/icl: Enable DC9 as lowest possible
 state during screen-off").

Fixes: 3e68928b7d4c ("drm/i915/icl: Enable DC9 as lowest possible state during screen-off")
Cc: Imre Deak <imre.deak@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Animesh Manna <animesh.manna@intel.com>
Cc: James Ausmus <james.ausmus@intel.com>
Cc: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Signed-off-by: Anusha Srivatsa <anusha.srivatsa@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
[Rodrigo added a commit message while merging]
Link: https://patchwork.freedesktop.org/patch/msgid/20181031202726.4021-1-anusha.srivatsa@intel.com

drm/i915/icl: Add DSS_CTL Registers

Add defines for DSS_CTL registers.
These registers specify the big joiner, splitter,
overlap pixels and info regarding
compression enabled on left or right branch.

v2:
- rebase. Remove overlapping defines(James Ausmus)
- Rename the register to ICL_DSS_CTL1/2_PIPE_ (manasi)
- take pixels as an argument for overlap.(Manasi)

v3:
- rebase. merge DSS_CTL1/2 introduced in Madhav's patch
  to avoid confusion (madhav chauhan)
- Rename registers in accordance to BSpec (Madhav, Rodrigo)
- Add define to conditionally check the buffer target depth (James Ausmus)

v4:
- remove redundant definitions.(madhav)

v5:
- Add mask for overlap pixels.
- Code Style changes.(Madhav)
v6:
- Code style changes. (Madhav)

Suggested-by: Madhav Chauhan <madhav.chauhan@intel.com>
Cc: Madhav Chauhan <madhav.chauhan@intel.com>
cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: James Ausmus <james.ausmus@intel.com>
Cc: Gaurav Singh <gaurav.k.singh@intel.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Manasi Navare <manasi.d.navare@intel.com>
Signed-off-by: Anusha Srivatsa <anusha.srivatsa@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/07021336cb87d09e8f97fbff709c4e686d7de536.1540900289.git.jani.nikula@intel.com

drm/i915/icl: Don't wait for empty FIFO

For Gen11 DSI, we don't need to wait for getting
DSI FIFO empty after sending DCS commands.

Signed-off-by: Madhav Chauhan <madhav.chauhan@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/5e078a0274c1fba2521cb14d7d02fd1038ec1b0e.1540900289.git.jani.nikula@intel.com

drm/i915/icl: Find DSI presence for ICL

This patch detects DSI presence for ICL platform
by reading VBT. DSI detection is done while initializing
DSI using newly added function intel_gen11_dsi_init.

v2 by Jani:
 - Preserve old behavour of intel_bios_is_dsi_present()
 - s/intel_gen11_dsi_init/icl_dsi_init/g

Signed-off-by: Madhav Chauhan <madhav.chauhan@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/2324cdfc8918bda3165354e5e0d15053b1074f14.1540900289.git.jani.nikula@intel.com

drm/i915/icl: Add DSI packet payload/header registers

This patch defines payload/header registers for each DSI
transcoder used for transmitting DSI packets.

v2 by Jani:
 - Drop full register mask and shift for payload
 - Use lower case for hex 0x

Signed-off-by: Madhav Chauhan <madhav.chauhan@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/18275c49215e512347a14bc38715314c2d6f95a4.1540900289.git.jani.nikula@intel.com

drm/i915/ICL: Add pre_pll_enable hook for ICL and set DFLEXDPMLE in this hook

In case of Legacy DP connector on TypeC port, the
flex IO DPMLE register is set to number of lanes configured
by the display driver which will be programmed into DDI_BUF_CTL
PORT_WIDTH_SELECTION.
This needs to be programmed before enabling the shared PLLs hence
add a pre_pll_enable hook for ICL and add this programming in that hook.

v2:
* Remove the check for combophy port (Jose)
* Simplify the port reversal check logic (Jose)

Cc: Lucas De Marchi <lucas.demarchi@intel.com>
Cc: Jose Roberto de Souza <jose.souza@intel.com>
Cc: Animesh Manna <animesh.manna@intel.com>
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Manasi Navare <manasi.d.navare@intel.com>
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Acked-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181023191248.26418-2-manasi.d.navare@intel.com

drm/i915/icl: Fix the macros for DFLEXDPMLE register bits

This patch fixes the macros used for defining the DFLEXDPMLE
register bit fields. This accounts for changes in the spec.

Fixes: a2bc69a1a9d6 ("drm/i915/icl: Add register definition for DFLEXDPMLE")
Cc: Animesh Manna <animesh.manna@intel.com>
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: Jose Roberto de Souza <jose.souza@intel.com>
Cc: <stable@vger.kernel.org> # v4.19+
Signed-off-by: Manasi Navare <manasi.d.navare@intel.com>
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181023191248.26418-1-manasi.d.navare@intel.com

drm/i915/icl: Fix crash when getting DPLL of a MST encoder in TC ports

enc_to_dig_port() returns NULL for encoders of type
INTEL_OUTPUT_DP_MST causing the crash bellow:

[ 2832.836101] BUG: unable to handle kernel paging request at 00000000000012b8
[ 2832.843062] PGD 0 P4D 0
[ 2832.845610] Oops: 0000 [#1] SMP
[ 2832.848764] CPU: 2 PID: 3577 Comm: kworker/2:0 Tainted: G        W         4.19.0-rc7+ #491
[ 2832.857106] Hardware name: Intel Corporation Ice Lake Client Platform/IceLake U DDR4 SODIMM PD RVP TLC, BIOS ICLSFWR1.R00.2352.A01.1808281852 08/28/2018
[ 2832.870734] Workqueue: events output_poll_execute
[ 2832.875480] RIP: 0010:icl_get_dpll+0xa4/0x5d0 [i915]
[ 2832.880449] Code: e9 03 f3 48 ab 8b 6e 74 41 8b 8c 24 5c 03 00 00 85 ed 0f 88 3f 02 00 00 83 fd 01 0f 8e ad 01 00 00 83 fd 05 0f 8f 2d 02 00 00 <83> ba b8 12 00 00 02 48 8b 36 0f 84 39 02 00 00 44 8b be ec 89 00
[ 2832.899176] RSP: 0018:ffffc90001b57a78 EFLAGS: 00010293
[ 2832.904404] RAX: 0000000000000000 RBX: ffffc90001b57a94 RCX: 0000000000083d60
[ 2832.911536] RDX: 0000000000000000 RSI: ffff8804a8c0dc00 RDI: ffffc90001b57b18
[ 2832.918668] RBP: 0000000000000003 R08: ffff8804a8c1f990 R09: ffff8804a8c1f990
[ 2832.925797] R10: 0000000000000000 R11: ffff8804a8e99600 R12: ffff8804a7760000
[ 2832.932930] R13: ffff88049e94d000 R14: ffff88049e94d000 R15: 000000000000000e
[ 2832.940063] FS:  0000000000000000(0000) GS:ffff8804b0300000(0000) knlGS:0000000000000000
[ 2832.948147] CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[ 2832.953893] CR2: 00000000000012b8 CR3: 0000000004a1d004 CR4: 0000000000760ee0
[ 2832.961027] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
[ 2832.968155] DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
[ 2832.975286] PKRU: 55555554
[ 2832.978003] Call Trace:
[ 2832.980496]  haswell_crtc_compute_clock+0x3d/0x68 [i915]
[ 2832.985841]  intel_crtc_atomic_check+0x61/0x340 [i915]
[ 2832.990987]  drm_atomic_helper_check_planes+0x130/0x1c0
[ 2832.996245]  intel_atomic_check+0x4d5/0x10f0 [i915]
[ 2833.001147]  drm_atomic_check_only+0x484/0x690
[ 2833.005629]  drm_atomic_commit+0x13/0x50
[ 2833.009564]  restore_fbdev_mode_atomic+0x1c9/0x1e0
[ 2833.014363]  drm_fb_helper_restore_fbdev_mode_unlocked+0x47/0x90
[ 2833.020368]  drm_fb_helper_set_par+0x29/0x50
[ 2833.024641]  drm_fb_helper_hotplug_event.part.33+0x92/0xb0
[ 2833.030130]  drm_kms_helper_hotplug_event+0x26/0x30
[ 2833.035013]  output_poll_execute+0x192/0x1b0
[ 2833.039293]  process_one_work+0x2a5/0x5f0
[ 2833.043315]  worker_thread+0x2d/0x3d0
[ 2833.046988]  ? rescuer_thread+0x340/0x340
[ 2833.051009]  kthread+0x112/0x130
[ 2833.054247]  ? kthread_create_worker_on_cpu+0x70/0x70
[ 2833.059307]  ret_from_fork+0x3a/0x50
[ 2833.062893] Modules linked in: i915 prime_numbers snd_hda_codec_realtek snd_hda_codec_generic asix snd_usb_audio snd_usbmidi_lib snd_seq_midi snd_seq_midi_event snd_rawmidi cdc_ether usbnet x86_pkg_temp_thermal xhci_pci xhci_hcd ucsi_acpi typec_ucsi typec efivarfs [last unloaded: prime_numbers]
[ 2833.088917] CR2: 00000000000012b8
[ 2833.092241] ---[ end trace 25f9fe3d47af2e75 ]---
[ 2833.096895] RIP: 0010:icl_get_dpll+0xa4/0x5d0 [i915]
[ 2833.101866] Code: e9 03 f3 48 ab 8b 6e 74 41 8b 8c 24 5c 03 00 00 85 ed 0f 88 3f 02 00 00 83 fd 01 0f 8e ad 01 00 00 83 fd 05 0f 8f 2d 02 00 00 <83> ba b8 12 00 00 02 48 8b 36 0f 84 39 02 00 00 44 8b be ec 89 00
[ 2833.120589] RSP: 0018:ffffc90001b57a78 EFLAGS: 00010293
[ 2833.125815] RAX: 0000000000000000 RBX: ffffc90001b57a94 RCX: 0000000000083d60
[ 2833.132946] RDX: 0000000000000000 RSI: ffff8804a8c0dc00 RDI: ffffc90001b57b18
[ 2833.140080] RBP: 0000000000000003 R08: ffff8804a8c1f990 R09: ffff8804a8c1f990
[ 2833.147213] R10: 0000000000000000 R11: ffff8804a8e99600 R12: ffff8804a7760000
[ 2833.154350] R13: ffff88049e94d000 R14: ffff88049e94d000 R15: 000000000000000e
[ 2833.161483] FS:  0000000000000000(0000) GS:ffff8804b0300000(0000) knlGS:0000000000000000
[ 2833.169565] CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[ 2833.175313] CR2: 00000000000012b8 CR3: 0000000004a1d004 CR4: 0000000000760ee0
[ 2833.182449] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
[ 2833.189578] DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
[ 2833.196712] PKRU: 55555554

MST ports are allocated from struct intel_dp_mst_encoder not from
struct intel_digital_port as regular ports, so to get the TC type it
is necessary check the primary digital port of the mst encoder.

Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181030215750.28213-5-jose.souza@intel.com

drm/i915: Initialize panel_vdd_work only for eDP ports

It is only used by eDP ports so no need to initialize it for each DP
port.

Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181030215750.28213-4-jose.souza@intel.com

drm/i915/icl: Set TC type to unknown when a sudden disconnection happen

Otherwise it would be in a inconsistent state as port is disconnected
but with a valid tc type.

Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181030215750.28213-3-jose.souza@intel.com

drm/i915/icl: Set TC type to unknown in the disconnection flow

Otherwise it would be in a inconsistent state as port is disconnected
but with a valid tc type.

Also setting it to unknown will earlier return
icl_tc_phy_disconnect() for any future calls to
intel_digital_port_connected(), this way we don't need to check if
port is marked as safe everytime.

Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181030215750.28213-2-jose.souza@intel.com

drm/i915/debugfs: Do not print cached information of a disconnected sink

Besides of give the expected output of i915_display_info it will also
avoid some aux ch transactions that would timeout by obvious reasons.

Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181030215750.28213-1-jose.souza@intel.com

drm/i915: Fix error handling for the NV12 fb dimensions check

Let's not leak obj->framebuffer_references when we decide that
the framebuffer domensions are not suitable for NV12.

Cc: stable@vger.kernel.org
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Vidya Srinivas <vidya.srinivas@intel.com>
Fixes: e44134f2673c ("drm/i915: Add NV12 support to intel_framebuffer_init")
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181029140031.11765-1-ville.syrjala@linux.intel.com
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>

drm/i915: Use intel_panel_actually_set_backlight() to disable PWM backlight

Use intel_panel_actually_set_backlight() instead of a direct
call to pwm_config() in pwm_disable_backlight().

The main benefit is consistent debug logging when we turn off the
backlight. Currently we see nothing in dmesg which made me wonder
whether the backlight was even getting turned off properly.

The second benefit is consistency; This is what we do for all
the other backlight implementations.

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181024155208.18987-1-ville.syrjala@linux.intel.com
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Acked-by: Jani Nikula <jani.nikula@intel.com>

drm/dp: Define payload size for DP SDP PPS packet

DP 1.4 spec defines DP secondary data packet for DSC
picture parameter set. This patch defines its payload size
according to the DP 1.4 specification.

Signed-off-by: Manasi Navare <manasi.d.navare@intel.com>
Cc: dri-devel@lists.freedesktop.org
Cc: Gaurav K Singh <gaurav.k.singh@intel.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Ville Syrjala <ville.syrjala@linux.intel.com>
Cc: Anusha Srivatsa <anusha.srivatsa@intel.com>
Acked-by: Sean Paul <seanpaul@chromium.org> (For merging through
drm-intel)
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181031001923.31442-7-manasi.d.navare@intel.com

drm/i915/dp: Validate modes using max Output BPP and slice count when DSC supported

When DSC is supported we need to validate the modes based on the
maximum supported compressed BPP and maximum supported slice count.
This allows us to allow the modes with pixel clock greater than the
available link BW as long as it meets the compressed BPP
and slice count requirements.

v3:
* Use the macro for dsc sink support (Jani N)
v2:
* Properly comment why we are right shifting the bpp value (Anusha)

Cc: Gaurav K Singh <gaurav.k.singh@intel.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Ville Syrjala <ville.syrjala@linux.intel.com>
Cc: Anusha Srivatsa <anusha.srivatsa@intel.com>
Signed-off-by: Manasi Navare <manasi.d.navare@intel.com>
Reviewed-by: Anusha Srivatsa <anusha.srivatsa@intel.com>
Reviewed-by: Gaurav K Singh <gaurav.k.singh@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181031001923.31442-6-manasi.d.navare@intel.com

drm/i915/dp: Add helpers for Compressed BPP and Slice Count for DSC

This patch adds helpers for calculating the maximum compressed BPP
supported with small joiner.
This also adds a helper for calculating the slice count in case
of small joiner.
These are inside intel_dp since they take into account hardware
limitations.

v6:
* Take mode_clock and mode_hdisplay as input arguments
so that this can be called in intel_dp_mode_valid (Manasi)
v5:
* Get the max slice width from DPCD
* Check against Min_Slice_width of 2560 (Anusha)
v4:
* #defines for PPR in slice count helper (Gaurav)
v3:
* Simply logic for bpp (DK)
* Limit the valid slice count by max supported by Sink (Manasi)
v2:
* Change the small joiner RAM buffer constant as bspec changed (Manasi)
* rename it as SMALL_JOINER since we are not enabling
big joiner yet (Anusha)

Cc: Gaurav K Singh <gaurav.k.singh@intel.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Ville Syrjala <ville.syrjala@linux.intel.com>
Cc: Anusha Srivatsa <anusha.srivatsa@intel.com>
Cc: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Signed-off-by: Manasi Navare <manasi.d.navare@intel.com>
Reviewed-by: Anusha Srivatsa <anusha.srivatsa@intel.com>
Reviewed-by: Gaurav K Singh <gaurav.k.singh@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181031001923.31442-5-manasi.d.navare@intel.com

drm/dp: DRM DP helper/macros to get DP sink DSC parameters

This patch adds inline functions and helpers for obtaining
DP sink's supported DSC parameters like DSC sink support,
eDP compressed BPP supported, maximum slice count supported
by the sink devices, DSC line buffer bit depth supported on DP sink,
DSC sink maximum color depth by parsing corresponding DPCD registers.

v4:
* Add helper to give line buf bit depth (Manasi)
* Correct the bit masking in color depth helper (manasi)
v3:
* Use SLICE_CAP_2 for DP (Anusha)
v2:
* Add DSC sink support macro (Jani N)

Cc: Gaurav K Singh <gaurav.k.singh@intel.com>
Cc: dri-devel@lists.freedesktop.org
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Ville Syrjala <ville.syrjala@linux.intel.com>
Cc: Anusha Srivatsa <anusha.srivatsa@intel.com>
Signed-off-by: Manasi Navare <manasi.d.navare@intel.com>
Reviewed-by: Anusha Srivatsa <anusha.srivatsa@intel.com>
Reviewed-by: Gaurav K Singh <gaurav.k.singh@intel.com>
Acked-by: Sean Paul <seanpaul@chromium.org> (For merging through
drm-intel)
Link: https://patchwork.freedesktop.org/patch/msgid/20181031001923.31442-4-manasi.d.navare@intel.com

drm/i915/dp: Cache the DP/eDP DSC DPCD register set on Hotplug/eDP Init

DSC is supported on eDP starting GEN 10 display (on GLK) and on DP starting
GEN 11.
This patch implements the discovery phase of DSC. On hotplug,
source reads the DSC DPCD register set (0x00060 - 0x0006F) to
read the decompression capabilities of the sink device.
This entire block of registers is cached in intel_dp so that
capability information can be used during DSC configuration
phase during compute_config phase of the modeset.
For eDP, this caching happens during the eDP initialization.
This caching is done only for eDP and DP rev >= 1.4

v5:
* Fix the block comment (Gaurav)
* Fix the commit message DSC DPCD addresses (Gaurav)
* Use DRM_ERROR for dpcd_read fail (Gaurav,Anusha)
v4:
* Cache these only for Gen >= 11
v3:
* Remove the dsc_sink_support field in intel_dp (Jani N)
v2:
* Clear the cached registers on hotplug always (Jani N)
* Combine the eDP and DP caching in same function (Jani N)

Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Ville Syrjala <ville.syrjala@linux.intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Anusha Srivatsa <anusha.srivatsa@intel.com>
Cc: Gaurav K Singh <gaurav.k.singh@intel.com>
Signed-off-by: Manasi Navare <manasi.d.navare@intel.com>
Reviewed-by: Anusha Srivatsa <anusha.srivatsa@intel.com>
Reviewed-by: Gaurav K Singh <gaurav.k.singh@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181031001923.31442-3-manasi.d.navare@intel.com

drm/dp: Add DP DSC DPCD receiver capability size define and missing SHIFT

This patch defines the DP DSC receiver capability size that gives
total number of DP DSC DPCD registers.
This also adds a missing #defines for DP DSC support missed in the
commit id (ab6a46ea6842ce "Add DPCD definitions for DP 1.4 DSC feature")

v3:
* MIN_SLICE_WIDTH = 2560 (Anusha)
* Define DP_DSC_SLICE_WIDTH_MULTIPLIER = 320
v2:
* Add SHIFT define and DECOMPRESSION_EN define missed in prev patch

Cc: dri-devel@lists.freedesktop.org
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Ville Syrjala <ville.syrjala@linux.intel.com>
Cc: Anusha Srivatsa <anusha.srivatsa@intel.com>
Cc: Gaurav K Singh <gaurav.k.singh@intel.com>
Signed-off-by: Manasi Navare <manasi.d.navare@intel.com>
Acked-by: Sean Paul <seanpaul@chromium.org> (For merging through
drm-intel)
Reviewed-by: Anusha Srivatsa <anusha.srivatsa@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181031001923.31442-2-manasi.d.navare@intel.com

drm/i915/dsc: Add slice_row_per_frame in DSC PPS programming

Add the newly added slice_row_per_frame parameter
in the Picture Parameter Set registers.
This defines the number of vertically stacked slices
in a frame.

Credits to Manasi for noticing bSpec change.

Suggested-by: Manasi Navare <manasi.d.navare@intel.com>
Cc: Manasi Navare <manasi.d.navare@intel.com>
Signed-off-by: Anusha Srivatsa <anusha.srivatsa@intel.com>
Reviewed-by: Manasi Navare <manasi.d.navare@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181031001923.31442-1-manasi.d.navare@intel.com

drm/i915/icl: Program HS_TX_TIMEOUT/LP_RX_TIMEOUT/TA_TIMEOUT registers

Program the timeout values (in escape clock) for HS TX, LP RX and TA
timeout.

HX TX: Ensure that host does not continuously transmit in the HS
state. If this timer expires, then host will gracefully end its HS
transmission and allow the link to enter into LP state.

LP RX: Monitor the length of LP receptions from Peripheral. If timeout
happens then host will drive the stop state onto all data lanes (only
Data Lane 0 should be receiving anything from the Peripheral). This
effectively takes back ownership of the bus transmit in the HS state.

TA timeout: Timeout valuefor monitoring Bus Turn-Around (BTA) sequence.
BTA sequence should complete within a bounded amount of time, with
peripheral acknowledging BTA by driving the stop state.

v2 by Jani:
 - Rebase
 - Use intel_dsi_bitrate() and intel_dsi_tlpx_ns(intel_dsi)
 - Squash HX TX, LP RX and TA timeout into one patch
 - Fix bspec mode set sequence reference
 - Add FIXME about two timeouts

Signed-off-by: Madhav Chauhan <madhav.chauhan@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/60e610ccffe5f8c09dee1c65828f28f25227efce.1540900289.git.jani.nikula@intel.com

drm/i915/icl: Define DSI timeout registers

This patch defines DSI_HTX_TO, DSI_LRX_H_TO, DSI_PWAIT_TO
and DSI_TA_TO registers for DSI transcoders '0' and '1'.
They are used for contention recovery on DPHY.

v2: Define SHIFT for bitfields.

v3 by Jani:
- Fix timeout bit definitions

Signed-off-by: Madhav Chauhan <madhav.chauhan@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/0b943c028a05edfd61c511d712c65c7e8bf70211.1540900289.git.jani.nikula@intel.com

drm/i915/icl: Disable DSI IO power

This patch configures mode of combo phy as DDI and
disable IO power for DDI ports used by DSI.

Signed-off-by: Madhav Chauhan <madhav.chauhan@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/b68d767717a3b86c26042d0b16abb3943756fcc4.1540900289.git.jani.nikula@intel.com

drm/i915/icl: Disable DSI ports

This patch disables both DSI ports by writing to
DDI_BUF_CTL registers as part of DSI encoder disable
sequence.

Signed-off-by: Madhav Chauhan <madhav.chauhan@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/be9a7dc1ed89ad38679c67ff1c1552f0b4604494.1540900289.git.jani.nikula@intel.com

drm/i915/icl: Disable portsync mode

This patch disables portsync mode if DSI link
is operating in dual link mode by writing to
TRANS_DDI_FUNC_CTL2 registers.

Signed-off-by: Madhav Chauhan <madhav.chauhan@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/3e608420b58930b6da478801bff018c6e964eb94.1540900289.git.jani.nikula@intel.com

drm/i915/icl: Disable DDI function

This patch disables DDI function by writing to
TRANS_DDI_FUNC_CTL registers of DSI ports as part
of DSI disable sequence.

Signed-off-by: Madhav Chauhan <madhav.chauhan@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/b0088d643247135ba96943fa14625f5a43f43633.1540900289.git.jani.nikula@intel.com

drm/i915/icl: Put DSI link in ULPS

As part of DSI disabling sequence, DSI link need to enter
in ULPS by writing into DSI_LP_MSG register. This patch
does the same using a wrapper function.

Signed-off-by: Madhav Chauhan <madhav.chauhan@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/50812f4bd37f95c053bef7eef4a95e5da029546f.1540900289.git.jani.nikula@intel.com

drm/i915/icl: Power down DSI panel

This patch sends command and executes display off,
assert reset, power off VBT seqeuences to power
down DSI panel. Patch also adds high level function
to wrap all the panel sepcific programming during
DSI disabling.

Signed-off-by: Madhav Chauhan <madhav.chauhan@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/efdafbf6b4d31123738b87b2d8264a9b5553eb32.1540900289.git.jani.nikula@intel.com

drm/i915/icl: Disable DSI transcoders

This patch disables transcoders by writing to TRANS_CONF
registers for each DSI ports.

v2 by Jani:
 - Wait for pipeconf active to go low

Signed-off-by: Madhav Chauhan <madhav.chauhan@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/c76035309fa721322cf9c1ca7fc42b822937c2f3.1540900289.git.jani.nikula@intel.com

drm/i915/icl: Turn OFF panel backlight

This patch disbles backlight of DSI panel by using VBT
BACKLIGHT_OFF sequence and panel specific disable functions.

Signed-off-by: Madhav Chauhan <madhav.chauhan@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/93cfbb198104deef4a281bbdef721385e4b6d954.1540900289.git.jani.nikula@intel.com

drm/i915/icl: Turn ON panel backlight

This patch enables backlight of DSI panel by using VBT
BACKLIGHT_ON sequence and panel specific functions.

Signed-off-by: Madhav Chauhan <madhav.chauhan@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/05987eea297689af0b9defcf745a921f76f9011d.1540900289.git.jani.nikula@intel.com

drm/i915/icl: Wait for header/payload credits release

Driver needs payload/header credits for sending any command
and data over DSI link. These credits are released once command
or data sent to link. This patch adds functions to wait for releasing
of payload and header credits.

As per BSPEC, driver needs to ensure that all of commands/data
has been dispatched to panel before the transcoder is enabled.
This patch implement those steps i.e. sending NOP DCS command,
wait for header/payload credit to be released etc.

v2 by Jani:
 - squash the credit wait helpers patch with the first user
 - pass dev_priv to the credit wait helpers
 - bikeshed credit helper names
 - wait for *at least* the current maximum number of credits
 - indentation fix
 - add helpers for credits available

Signed-off-by: Madhav Chauhan <madhav.chauhan@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/84bc509beabf2a2d1324a9f2a67ab4ebe05b10a6.1540900289.git.jani.nikula@intel.com

drm/i915/ringbuffer: change header SPDX identifier to MIT

Commit b24413180f56 ("License cleanup: add SPDX GPL-2.0 license
identifier to files with no license") added "SPDX-License-Identifier:
GPL-2.0" to files which previously had no license, change this to MIT
for intel_ringbuffer.h matching the license text of intel_ringbuffer.c.

Signed-off-by: Jonathan Gray <jsg@jsg.id.au>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181031005331.20775-1-jsg@jsg.id.au

drm/i915/icl: Power on DSI panel

This patch execute poweron, deassert reset, display on
VBT sequences and send TURN_ON DSI command to panel for
powering it up.

Signed-off-by: Madhav Chauhan <madhav.chauhan@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/8acb06fa634fe9637fdc09a3f5d2588b9138224f.1540900289.git.jani.nikula@intel.com

drm/i915/icl: Set max return packet size for DSI panel

This patch programs maximum size of the payload transmitted
from peripheral back to the host processor using short packet
as a part of panel programming.

v2: Rebase

v3 by Jani:
 - Add FIXME note.

Signed-off-by: Madhav Chauhan <madhav.chauhan@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/ed9df910326adf32eb2bc1cd1a5097d0dda94da8.1540900289.git.jani.nikula@intel.com

drm/i915/dsi: move connector mode functions to common file

Move DSI connector functions to intel_dsi.c and make them available to
both legacy and ICL DSI.

v2 by Jani:
 - Move the functions to intel_dsi.c
 - Don't reuse intel_dsi_connector_destroy()

Signed-off-by: Madhav Chauhan <madhav.chauhan@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/99244c6edf4a26ef2e279c7160d22dbbb5cd95f2.1540900289.git.jani.nikula@intel.com

drm/i915/icl: Move dsi host init code to common file

This patch moves intl_dsi_host_init() code to intel_dsi.c so that legacy
and gen11 DSI code can share this code.

v2 by Jani:
 - Move the shared stuff to intel_dsi.c

Signed-off-by: Madhav Chauhan <madhav.chauhan@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1ee42b2d3c639e3f3c14a2c1595b8778901574d4.1540900289.git.jani.nikula@intel.com

drm/i915/selftest: test aligned offsets for 64K

When using softpin it's not enough to just pad the vma size, we also
need to ensure the vma offset is at the start of the pt boundary, if we
plan to utilize 64K pages. Therefore to improve test coverage we should
use both aligned and unaligned gtt offsets in igt_write_huge.

Suggested-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Matthew Auld <matthew.auld@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20181029203734.21936-1-matthew.auld@intel.com

drm/i915/gtt: Revert "Disable read-only support under GVT"

This reverts commit c9e666880de5a1fed04dc412b046916d542b72dd.

Checked GVT codes that guest PPGTT PTE flag bits are propagated
to shadow PTE. Read/write bit is not changed. Further tested by
i915 self-test case "igt_ctx_readonly". No error or GPU hang was
detected. So enable read-only support under GVT.

Signed-off-by: Hang Yuan <hang.yuan@linux.intel.com>
Acked-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1540883281-11359-1-git-send-email-hang.yuan@linux.intel.com
Acked-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>

drm/i915/icl: Enable DC9 as lowest possible state during screen-off

ICL supports DC5, DC6, and DC9. Enable DC9 during screen-off, and enable
DC5/6 when appropriate.

v2: (James Ausmus)
 - Also handle ICL as GEN9_LP in i915_drm_suspend_late and
   i915_drm_suspend_early
 - Add DC9 to gen9_dc_mask for ICL
 - Re-order GEN checks for newest platform first
 - Use INTEL_GEN instead of INTEL_INFO->gen
 - Use INTEL_GEN >= 11 instead of IS_ICELAKE
 - Consolidate GEN checks

v3: (James Ausmus)
 - Also allow DC6 for ICL (Imre, Art)
 - Simplify !(GEN >= 11) to GEN < 11 (Imre)

v4: (James Ausmus)
 - Don't call intel_power_sequencer_reset after DC9 for Gen11+, as the
   PPS regs are Always On
 - Rebase against upstream changes

v5: (Anusha Srivatsa)
- rebased against the latest upstream changes.

v6: (Anusha Srivatsa)
- rebased.Use INTEL_GEN consistently.
- Simplify the code (Rodrigo)

v7: rebased. Change order according to platforms(Jyoti)

v8: rebased. Change the check from platform specific to
HAS_PCH_SPLIT(). Add comment in code to be more clear.(Rodrigo)

Cc: Imre Deak <imre.deak@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Animesh Manna <animesh.manna@intel.com>
Signed-off-by: James Ausmus <james.ausmus@intel.com>
Signed-off-by: Anusha Srivatsa <anusha.srivatsa@intel.com>
Tested-by: Jyoti Yadav <jyoti.r.yadav@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181029221410.4423-1-anusha.srivatsa@intel.com

drm/i915: Stop calling intel_opregion unregister/register in suspend/resume

If we reduce the suspend function for intel_opregion to do the minimum
required, the resume function can also do the simple task of notifier
the ACPI bios that we are back. This avoid some nasty restrictions on
the likes of register_acpi_notifier() that are not allowed during the
early phase of resume.

v2: Keep the order of acpi notify vs turning off ardy/drdy the same.

Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Imre Deak <imre.deak@intel.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Acked-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181030110554.4111-1-chris@chris-wilson.co.uk

drm/i915/gtt: Reuse the read-only 64KiB scratch page and directories

If we can prevent stray writes from landing in the scratch page, we can
reuse the same page and same scratch PT for all contexts without fear of
information leaks and side-channels.

Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Matthew Auld <matthew.auld@intel.com>
Reviewed-by: Matthew Auld <matthew.auld@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181029182721.29568-2-chris@chris-wilson.co.uk

drm/i915/gtt: Record the scratch pte

Record the scratch PTE encoding upon creation rather than recomputing
the bits everytime. This is important for the next patch where we forgo
having a valid scratch page with which we may compute the bits and so
require keeping the PTE value instead.

v2: Fix up scrub_64K to use scratch_pte as well.

Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Matthew Auld <matthew.auld@intel.com>
Reviewed-by: Matthew Auld <matthew.auld@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181029182721.29568-1-chris@chris-wilson.co.uk

drm/i915: Switch the order of function parameters

intel_fb_pitch_limit() has the parameters pixel_format and fb_modifier
switched in their positions. The parameters are however used correctly,
but change the order for consistency.

Also use kernel data types for both parameters.

Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181026195342.16828-1-dhinakaran.pandiyan@intel.com

drm/i915: Do not program aux plane offsets on gen11+

The PLANE_AUX_OFFSET mmio does not exist on ICL, do not program it.  We'll
still calculate the aux offset as it is required for adjusing x-y offsets.

Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181026193805.11077-2-dhinakaran.pandiyan@intel.com

drm/i915: Add function to check for linear surfaces

A framebuffer can comprise surfaces with distinct tiling formats,
making checks against modifier alone insufficient. Make use of a
function to identify a linear surface based on both modifier and color
plane.

v2: Typo fix
v3: remove 'inline' from function definition (Ville)

Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181026193805.11077-1-dhinakaran.pandiyan@intel.com

drm/i915: Move VIDEO_DIP_CTL definitions to their right place.

The bits weren't defined in descending order.
v2: Move definitions in a separate patch (Manasi)

Cc: Manasi Navare <manasi.d.navare@intel.com>
Signed-off-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Reviewed-by: Manasi Navare <manasi.d.navare@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181005185643.31660-2-dhinakaran.pandiyan@intel.com

drm/i915: Fix VIDEO_DIP_CTL bit shifts

The shifts for VSC_SELECT bits are wrong, fix it. Good thing is the
definitions are unused.

v2: Moves definitions in another patch (Manasi)
Cc: Manasi Navare <manasi.d.navare@intel.com>
Cc: Anusha Srivatsa <anusha.srivatsa@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Fixes: 7af2be6d54d4 ("drm/i915/icl: Add VIDEO_DIP registers")
Signed-off-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Reviewed-by: Manasi Navare <manasi.d.navare@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181005185643.31660-1-dhinakaran.pandiyan@intel.com

drm/i915: Simplify has_sagv function

The specially case for SKL for not controlled sagv
is already taken care inside intel_enable_sagv, so there's
no need to duplicate the check here.

v2: Go one step further and remove skl special case. (Jani)
v3: Separate runtime status handle from has_sagv flag.
v4: Go back and accept simple Jani proposed solution.

Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181026200317.21726-1-rodrigo.vivi@intel.com

drm/i915/selftests: Test vm isolation

The vm of two contexts are supposed to be independent, such that a stray
write by one cannot be detected by another. Normally the GTT is filled
explicitly by userspace, but the space in between objects is filled with
a scratch page -- and that scratch page should not be able to form an
inter-context backchannel.

Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Matthew Auld <matthew.auld@intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Reviewed-by: Matthew Auld <matthew.auld@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181029172925.10159-1-chris@chris-wilson.co.uk

drm/i915/glk: Remove 99% limitation.

While checking the opportunity to add a display_gen
check to allow glk and cnl to be on same bucket I noticed
these FIXME cases here.

So I got the confirmation from HW architect that we actually
never needed this workaround.

"GLK supports 2 pixel per clock, so pixel clock can be up to 2 * cdclk."

So, this reverts commit 97f55ca5b662 ("drm/i915/glk: limit pixel
 clock to 99% of cdclk workaround")

Fixes: 97f55ca5b662 ("drm/i915/glk: limit pixel clock to 99% of cdclk workaround")
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Madhav Chauhan <madhav.chauhan@intel.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Clinton Taylor <clinton.a.taylor@intel.com>
Cc: Arthur J Runyan <arthur.j.runyan@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181026005636.22274-1-rodrigo.vivi@intel.com

drm/i915: Kill GEN_FOREVER

commit ac657f6461e5 ("drm/i915: Introduce IS_GEN macro") introduced
GEN_FOREVER that was never used.

My first attempt was to rename it to FOREVER since GEN is
already part of the macro. Then I used coccinelle to change all
-INTEL_GEN(e1) >= e2
+INTEL_GEN_RANGE(e1, e2, FOREVER)
-INTEL_GEN(e1) <= e2
+INTEL_GEN_RANGE(e1, 0, e2)

and I liked it.

However I didn't like very much the remaining
INTEL_GEN(dev_priv) < n

and:
INTEL_GEN(e1) < n
INTEL_GEN_RANGE(e1, 0, n - 1)

didn't make much sense either.

So INTEL_GEN use for > or < seems a better unified way for unlimited
bounds. So, no reason to keep GEN_FOREVER here.

Let's kill before someone start using it.

v2: Remove remaining GEN_FOREVER forgotten in a comment. (Daniel)

Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20181026195143.20353-2-rodrigo.vivi@intel.com

drm/i915: Prefer IS_GEN<n> check with bitmask.

Whenever possible we should stick with IS_GEN<n> checks.

Bitmaks has been introduced on commit ae7617f0ef18 ("drm/i915:
Allow optimized platform checks") for efficiency.

Let's stick with it whenever possible.

This patch was generated with coccinelle:

spatch -sp_file is_gen.cocci *{c,h} --in-place

is_gen.cocci:
@gen2@ expression e; @@
-INTEL_GEN(e) == 2
+IS_GEN2(e)
@gen3@ expression e; @@
-INTEL_GEN(e) == 3
+IS_GEN3(e)
@gen4@ expression e; @@
-INTEL_GEN(e) == 4
+IS_GEN4(e)
@gen5@ expression e; @@
-INTEL_GEN(e) == 5
+IS_GEN5(e)
@gen6@ expression e; @@
-INTEL_GEN(e) == 6
+IS_GEN6(e)
@gen7@ expression e; @@
-INTEL_GEN(e) == 7
+IS_GEN7(e)
@gen8@ expression e; @@
-INTEL_GEN(e) == 8
+IS_GEN8(e)
@gen9@ expression e; @@
-INTEL_GEN(e) == 9
+IS_GEN9(e)
@gen10@ expression e; @@
-INTEL_GEN(e) == 10
+IS_GEN10(e)
@gen11@ expression e; @@
-INTEL_GEN(e) == 11
+IS_GEN11(e)

Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181026195143.20353-1-rodrigo.vivi@intel.com

drm/i915: Define Intel HDCP2.2 registers

Intel HDCP2.2 registers are defined with addr offsets and bit details.

v2:
  Replaced the arith calc with _PICK [Sean Paul]
v3:
  No changes.
v4:
  %s/HDCP2_CTR_DDI/HDCP2_CTL_DDI [Uma]
v5:
  Added parentheses for the parameters of macro.
v6:
  No changes
v7:
  No changes

Signed-off-by: Ramalingam C <ramalingam.c@intel.com>
Reviewed-by: Sean Paul <seanpaul@chromium.org>
Reviewed-by: Uma Shankar <uma.shankar@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/1540806351-7137-7-git-send-email-ramalingam.c@intel.com

drm: HDMI and DP specific HDCP2.2 defines

This patch adds HDCP register definitions for HDMI and DP HDCP
adaptations.

HDMI specific HDCP2.2 register definitions are added into drm_hdcp.h,
where as HDCP2.2 register offsets in DPCD offsets are defined at
drm_dp_helper.h.

v2:
  bit_field definitions are replaced by macros. [Tomas and Jani]
v3:
  No Changes.
v4:
  Comments style and typos are fixed [Uma]
v5:
  Fix for macros.
v6:
  Adds _MS to the timeouts to represent units [Sean Paul]
v7:
  Macro DP_HDCP_2_2_REG_EKH_KM_OFFSET renamed [Uma]
  Redundant macro is removed [Uma]

Signed-off-by: Ramalingam C <ramalingam.c@intel.com>
Reviewed-by: Sean Paul <seanpaul@chromium.org>
Acked-by: Sean Paul <seanpaul@chromium.org> (for merging through drm-intel)
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/1540806351-7137-6-git-send-email-ramalingam.c@intel.com

drm: hdcp2.2 authentication msg definitions

This patch defines the hdcp2.2 protocol messages for authentication.

v2:
  bit_fields are removed. Instead bitmasking used. [Tomas and Jani]
  prefix HDCP_2_2_ is added to the macros. [Tomas]
v3:
  No Changes.
v4:
  Style and spellings are fixed [Uma]
v5:
  Fix for macros.
v6:
  comment for Type is improved [Sean Paul]
v7:
  %s/HDCP_2_2_LPRIME_HALF_LEN/HDCP_2_2_V_PRIME_HALF_LEN [Uma]
  %s/uintxx_t/uxx
v8:
  %s/eceiver_id/receiver_id

Signed-off-by: Ramalingam C <ramalingam.c@intel.com>
Reviewed-by: Uma Shankar <uma.shankar@intel.com>
Acked-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/1540806351-7137-5-git-send-email-ramalingam.c@intel.com

drm/i915: Reassigning log level for HDCP failures

As a policy, this change considers all I915 programming failures and
HW failures as ERRORS. Where as all HDCP failures due to the sink is
considered as DEBUG logs.

Signed-off-by: Ramalingam C <ramalingam.c@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/1540806351-7137-3-git-send-email-ramalingam.c@intel.com

drm/i915: wrapping all hdcp var into intel_hdcp

Considering significant number of HDCP specific variables, it will
be clean to have separate struct for HDCP.

New structure called intel_hdcp is added within intel_connector.

v2:
  struct hdcp statically allocated. [Sean Paul]
  enable and disable function parameters are retained.[Sean Paul]
v3:
  No Changes.
v4:
  Commit msg is rephrased [Uma]
v5:
  Comment for mutex definition.
v6:
  hdcp_ prefix from all intel_hdcp members are removed [Sean Paul]
  inline function intel_hdcp_to_connector is defined [Sean Paul]
v7:
  %s/uint64_t/u64
v8:
  Rebased

Signed-off-by: Ramalingam C <ramalingam.c@intel.com>
Reviewed-by: Sean Paul <seanpaul@chromium.org>
Reviewed-by: Uma Shankar <uma.shankar@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/1540806351-7137-2-git-send-email-ramalingam.c@intel.com

drm/i915: Park signaling thread while wrapping the seqno

A danger encountered when resetting the seqno (using
debugfs/i915_next_seqno) is that as we change the breadcrumb stored in
the HWSP, it may be inspected by the signaler thread leading to
confusion in our sanity checks.

<0> [136.331342] i915/sig-347     3..s1 136336154us : execlists_submission_tasklet: rcs0 awake?=1, active=5
<0> [136.331373] i915/sig-347     3d.s2 136336155us : process_csb: rcs0 cs-irq head=5, tail=0
<0> [136.331402] i915/sig-347     3d.s2 136336155us : process_csb: rcs0 csb[0]: status=0x00000018:0x00000002, active=0x5
<0> [136.331434] i915/sig-347     3d.s2 136336156us : process_csb: rcs0 out[0]: ctx=2.1, global=219 (fence 46:8455) (current 219), prio=0
<0> [136.331466] i915/sig-347     3d.s2 136336156us : process_csb: rcs0 completed ctx=2
<0> [136.332027] gem_exec-1049    0.... 136336246us : reset_all_global_seqno.part.5: rcs0 seqno 219 (current 219) -> -43
<0> [136.332056] gem_exec-1049    0.... 136336251us : reset_all_global_seqno.part.5: bcs0 seqno 183 (current 183) -> -43
<0> [136.332085] gem_exec-1049    0.... 136336255us : reset_all_global_seqno.part.5: vcs0 seqno 191 (current 191) -> -43
<0> [136.332114] gem_exec-1049    0.... 136336259us : reset_all_global_seqno.part.5: vcs1 seqno 180 (current 180) -> -43
<0> [136.332143] gem_exec-1049    0.... 136336262us : reset_all_global_seqno.part.5: vecs0 seqno 212 (current 212) -> -43
<0> [136.332174] i915/sig-347     3.... 136336280us : intel_breadcrumbs_signaler: intel_breadcrumbs_signaler:673 GEM_BUG_ON(!i915_request_completed(rq))

Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181024104939.2861-1-chris@chris-wilson.co.uk

drm/i915/selftests: Check for hangs mid context execution tests

Use the live_test struct to record the reset count before and compare it
at the end of the test to assert that no mystery hang occurred during the
test.

v2: Check per-engine resets as well

Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181012122404.10874-1-chris@chris-wilson.co.uk

drm/i915/icl: Store available engine masks in INTEL_INFO

Upcoming GuC code will need to read the fused off engine masks as well,
and will also want to have them as enabled instead of disabled masks.

To consolidate the read-out place we can store them in this fashion inside
INTEL_INFO so they can be easily referenced in the future.

Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Reviewed-by: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181018104106.30147-1-tvrtko.ursulin@linux.intel.com

drm/i915: Compare user's 64b GTT offset even on 32b

Beware mixing unsigned long constants and 64b values, as on 32b the
constant will be zero extended and discard the high 32b when used as
a mask!

Reported-by: Sergii Romantsov <sergii.romantsov@globallogic.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=108282
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: stable@vger.kernel.org
Reviewed-by: Matthew Auld <matthew.auld@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181025091823.20571-2-chris@chris-wilson.co.uk

drm/i915: Mark up GTT sizes as u64

Since we use a 64b virtual GTT irrespective of the system, we want to
ensure that the GTT computations remains 64b even on 32b systems,
including treatment of huge virtual pages.

No code generation changes on 64b:

Reported-by: Sergii Romantsov <sergii.romantsov@globallogic.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=108282
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: stable@vger.kernel.org
Reviewed-by: Matthew Auld <matthew.auld@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181025091823.20571-1-chris@chris-wilson.co.uk

drm/i915/hdmi: Add HDMI 2.0 audio clock recovery N values

HDMI 2.0 594Mhz modes were incorrectly selecting 25.200Mhz Automatic N value
mode instead of HDMI specification values.

V2: Fix 88.2 Hz N value

Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: stable@vger.kernel.org
Signed-off-by: Clint Taylor <clinton.a.taylor@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1540493521-1746-2-git-send-email-clinton.a.taylor@intel.com

drm/i915: Ensure proper HDA suspend/resume ordering with a device link

In order to ensure that our system suspend and resume callbacks are
called in the correct order wrt. those of the HDA driver add a device
link to the HDA driver during audio component binding time. With i915 as
the supplier and HDA as the consumer the PM framework will guarantee
the HDA->i915 suspend (and shutdown) and i915->HDA resume order.

Atm, the lack of this ordering is not a problem, since all the i915
suspend/resume steps that need to be ordered wrt. the HDA driver's
suspend/resume steps are separated out to the i915
suspend_late/resume_early hooks. That will change in a follow-up
patchset where we'll need this ordering guarantee for steps that are in
the i915 suspend/resume hooks (and which can't be moved to
suspend_late/resume_early for other reasons). So this patch is a
preparation for that follow-up patchset.

The change also allows us to move towards removing the i915
suspend_late/resume_early hooks alltogether.

Since we only need to ensure the ordering during suspend/resume and not
during driver probing create the link with DL_FLAG_STATELESS. Since the
probe time ordering has to be optional we use the component framework
for that.

Similarly for runtime PM we depend on the audio driver getting/putting
an i915 runtime PM reference whenever it needs it (along with the proper
i915 display power domain) via the audio component ops get_power /
put_power hooks. So we create the device link without
DL_FLAG_PM_RUNTIME.

v2: (Ville)
- Add a note to the commit message about not using the device link
  runtime PM ordering.
- Handle the error return from device_link_add().

Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Takashi Iwai <tiwai@suse.de>
Cc: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181023144310.8272-1-imre.deak@intel.com

drm/i915: Mark skl_update_plane and skl_disable_plane as static

make W=1 caught the implicit prototypes (as would sparse):

drivers/gpu/drm/i915/intel_sprite.c:462:1: error: no previous prototype for ‘skl_update_plane’ [-Werror=missing-prototypes]
 skl_update_plane(struct intel_plane *plane,
 ^~~~~~~~~~~~~~~~
drivers/gpu/drm/i915/intel_sprite.c:487:1: error: no previous prototype for ‘skl_disable_plane’ [-Werror=missing-prototypes]
 skl_disable_plane(struct intel_plane *plane, struct intel_crtc *crtc)
 ^~~~~~~~~~~~~~~~~

Fixes: 1e364f9008a7 ("drm/i915/gen11: Program the Y and UV plane for planar mode correctly, v3.")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181024105402.18915-1-chris@chris-wilson.co.uk

drm/i915/perf: Fix warning in documentation

Forgot to add the description of this option in a previous commit.

Signed-off-by: Lionel Landwerlin <lionel.g.landwerlin@intel.com>
Fixes: cd956bfcd0f58d ("drm/i915/perf: add a parameter to control the size of OA buffer")
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20181024105158.4732-1-lionel.g.landwerlin@intel.com

drm/i915: Don't apply the 16Gb DIMM wm latency w/a to BXT/GLK

The 16Gb DIMM w/a is not applicable to BXT or GLK. Limit it to
the appropriate platforms.

This was especially harsh on GLK since we don't even try to read
the DIMM information on that platforms, hence valid_dimm was
always false and thus we always tried to apply the w/a.
Furthermore the w/a pushed the level 0 latency above the
level 1 latency, which doesn't really make sense.

v2: Do the check when populating is_16gb_dimm (Mahesh)

Cc: Mahesh Kumar <mahesh1.kumar@intel.com>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Fixes: 86b592876cb6 ("drm/i915: Implement 16GB dimm wa for latency level-0")
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181023182102.31549-1-ville.syrjala@linux.intel.com
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Mahesh Kumar <mahesh1.sh.kumar@gmail.com>

drm/i915/gen11: Expose planar format support on gen11, v2.

Now that we implemented support for planar formats on gen11, we can
finally advertise it.

Changes since v1:
- Re-add change to skl_plane_has_planar(), was lost in rebase noise.

Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181022134514.14756-1-maarten.lankhorst@linux.intel.com

drm/i915/gen11: Program the Y and UV plane for planar mode correctly, v3.

The UV plane is the master plane that does all color correction etc.
It needs to be programmed with the dimensions for color plane 1 (UV).

The Y plane just feeds the Y pixels to it. Program the scaler from the
master only, and set PLANE_CTL_YUV420_Y_PLANE on the slave plane.

Changes since v1:
- Make a common skl_program_plane, and use it for both plane updates.
Changes since v2:
- Make color_plane explicit, to clarify skl_update_plane(). (Ville)

Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181018115134.9061-8-maarten.lankhorst@linux.intel.com

drm/i915/gen11: Program the chroma upsampler for HDR planes.

We configure the chroma upsampler with the same chroma siting as
used by the scaler for consistency, the chroma upsampler is used
instead of the scaler for YUV 4:2:0 on ICL's HDR planes.

Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181018115134.9061-7-maarten.lankhorst@linux.intel.com

drm/i915/gen11: Program the scalers correctly for planar formats, v3.

The first 3 planes (primary, sprite 0 and 1) have a dedicated chroma
upsampler to upscale YUV420 to YUV444 and the scaler should only be
used for upscaling. Because of this we shouldn't program the scalers
in planar mode if NV12 and the chroma upsampler are used. Instead
program the scalers like on normal planes.

Sprite 2 and 3 have no dedicated scaler, and need to program the
selected Y plane in the scaler mode.

Changes since v1:
- Make the comment less confusing.
Changes since v2:
- Fix checkpatch warning (Matt)
- gen10- -> Pre-gen11 (Ville)
- PS_SCALER_MODE_PACKED -> PS_SCALER_MODE_NORMAL. (Matt)
- Add comment about scaler mode in intel_atomic_setup_scaler(). (Matt)
- Rename need_scaling to need_scaler. (Matt)
- Move the crtc need_scaling check to skl_update_scaler_crtc().

Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181018115134.9061-6-maarten.lankhorst@linux.intel.com

drm/i915/gen11: Handle watermarks correctly for separate Y/UV planes, v2.

Skylake style watermarks program the UV parameters into wm->uv_wm,
and have a separate DDB allocation for UV blocks into the same plane.

Gen11 watermarks have a separate plane for Y and UV, with separate
mechanisms. The simplest way to make it work is to keep the current
way of programming watermarks and calculate the Y and UV plane
watermarks from the master plane.

Changes since v1:
- Constify crtc_state where possible.
- Make separate paths for planar formats in skl_build_pipe_wm() (Matt)
- Make separate paths for calculating total data rate. (Matt)
- Make sure UV watermarks are unused on gen11+ by adding a WARN. (Matt)

Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181018115134.9061-5-maarten.lankhorst@linux.intel.com

drm/i915/gen11: Link nv12 Y and UV planes in the atomic state, v5.

To make NV12 working on icl, we need to update 2 planes simultaneously.
I've chosen to do this in the CRTC step after plane validation is done,
so we know what planes are (in)visible. The linked Y plane will get
updated in intel_plane_update_planes_on_crtc(), by the call to
update_slave, which gets the master's plane_state as argument.

The link requires both planes for atomic_update to work,
so make sure skl_ddb_add_affected_planes() adds both states.

Changes since v1:
- Introduce icl_is_nv12_y_plane(), instead of hardcoding sprite numbers.
- Put all the state updating login in intel_plane_atomic_check_with_state().
- Clean up changes in intel_plane_atomic_check().
Changes since v2:
- Fix intel_atomic_get_old_plane_state() to actually return old state.
- Move visibility changes to preparation patch.
- Only try to find a Y plane on gen11, earlier platforms only require
  a single plane.
Changes since v3:
- Fix checkpatch warning about to_intel_crtc() usage.
- Add affected planes from icl_add_linked_planes() before check_planes(),
  it's a cleaner way to do this. (Ville)
Changes since v4:
- Clear plane links in icl_check_nv12_planes() for clarity.
- Only pass crtc_state to icl_check_nv12_planes().
- Use for_each_new_intel_plane_in_state() in icl_check_nv12_planes.
- Rename aux to linked. (Ville)

Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181022135152.15324-1-maarten.lankhorst@linux.intel.com
[mlankhorst: Change bool slave to u32, to satisfy checkpatch]
[mlankhorst: Add WARN_ON's based on Ville's suggestion]

drm/i915/gen11: Enable 6 sprites on gen11

Gen11 supports 7 planes + 1 cursor on each pipe. Bump
I915_MAX_PLANES to 8, and set num_sprites correctly.

Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
[mlankhorst: Move the skl/bxt comment to the BXT branch. (Matt)]
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181018115134.9061-3-maarten.lankhorst@linux.intel.com

drm/i915: Fix unsigned overflow when calculating total data rate, v2.

On gen11, we can definitely smash the 32-bits barrier with just a
when we enable all planes in the next patch.

Changes since v1:
- Use div64_u64 (ickle).

Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181022102000.30255-1-maarten.lankhorst@linux.intel.com

drm/i915: Move the DDC/AUX failure msgs to debug log

When a HDCP authentication is in progress, if the display sink is
hot unplugged, all DDC/AUX transaction related to the HDCP
authentication will fail.

This patch moves those kind of HDCP DDC/AUX failures into the debug
logs instead of errors.

v2:
  Bksv invalid state is provided as debug msg

Signed-off-by: Ramalingam C <ramalingam.c@intel.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/1540291288-22185-1-git-send-email-ramalingam.c@intel.com

drm/i915/debugfs: hdcp capability of a sink

Add a debugfs entry for providing the hdcp capabilities of the sink
connected to the HDCP capable connectors.

v2:
  Squashed the sink's hdcp capability into this patch. [Daniel]

Signed-off-by: Ramalingam C <ramalingam.c@intel.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/1540286550-20399-4-git-send-email-ramalingam.c@intel.com

drm/i915: hdcp_check_link only on CP_IRQ

HDCP check link is invoked only on CP_IRQ detection, instead of all
short pulses.

v3:
  No Changes.
v4:
  Added sean in cc and collected the reviewed-by received.
v5:
  No Change.
v6:
  No Change.
v7:
  No Change.
v8:
  Rebased.

Signed-off-by: Ramalingam C <ramalingam.c@intel.com>
cc: Sean Paul <seanpaul@chromium.org>
Reviewed-by: Uma Shankar <uma.shankar@intel.com>
Reviewed-by: Sean Paul <seanpaul@chromium.org>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/1540286550-20399-3-git-send-email-ramalingam.c@intel.com

drm/i915: Pullout the bksv read and validation

For reusability purpose, this patch implements the hdcp1.4 bksv's
read and validation as a functions.

For detecting the HDMI panel's HDCP capability this fucntions will be
used.

v2:
  Rebased.
v3:
  No Changes.
v4:
  inline tag is removed with modified error msg.
v5:
  No Changes.
v6:
  No Changes.
v7:
  Realigned the code.

Signed-off-by: Ramalingam C <ramalingam.c@intel.com>
Reviewed-by: Sean Paul <seanpaul@chromium.org>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/1540286550-20399-2-git-send-email-ramalingam.c@intel.com

drm/i915/guc: Propagate the fw xfer timeout

Propagate the timeout on transferring the fw back to the caller where it
may act upon it, usually by restarting the xfer before failing.

v2: Simplify the wait to only wait upon the guc signaling completion,
with an assertion that the fw xfer must have completed for it to be
ready!

Testcase: igt/drv_selftest/live_hangcheck
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Michal Wajdeczko <michal.wajdeczko@intel.com>
Cc: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Reviewed-by: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181018195536.11522-1-chris@chris-wilson.co.uk

drm/i915/sdvo: Utilize intel_panel for fixed_mode

Remove the local lvds fixed mode pointer from the sdvo encoder
structure and instead utilize intel_panel like everyone else.

v2: intel_sdvo_destroy() is gone

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180917151504.8754-2-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>