Szabolcs Hubai [Wed, 28 Sep 2022 00:55:01 +0000 (02:55 +0200)]
ramips: mt7621: use seama-lzma-loader for D-Link DIR-860L B1
Fix the LZMA ERROR 1 with a single line of recipe instead of duplicating
"uimage-lzma-loader".
While reviewing my original submission of commit
ce1957100411 David
suggested to use $(Device/uimage-lzma-loader), but due to the specific
needs of the vendor bootloader that simple oneliner didn't work.
The new $(Device/seama-lzma-loader) is for those SEAMA capable
bootloaders.
Signed-off-by: Szabolcs Hubai <szab.hu@gmail.com>
Szabolcs Hubai [Tue, 27 Sep 2022 22:54:36 +0000 (00:54 +0200)]
ramips: rt3883: use seama-lzma-loader for D-Link DIR-645
In the support topic [0] of the GitHub issue #10634 it was found out
(based on boot logs) that the uimage-lzma-loader (commit
09faa73c53bd)
never worked, as an earlier workaround (commit
6fba88de1913) negated
the recipe:
3: System Boot system code via Flash.
## Booting image at
bc050000 ...
raspi_read: from:50000 len:40
.raspi_read: from:50000 len:c
.raspi_read: from:50000 len:1fa000
................................We have SEAMA, Image Size =
2072512
Verifying Checksum ...
Uncompressing SEAMA linux.lzma ... OK
## Transferring control to Linux (at address
80000000) ...
## Giving linux memsize in MB, 64
Starting kernel ...
[ 0.000000] Linux version 5.4.188 (builder@buildhost) (gcc version 8.4.0 (OpenWrt GCC 8.4.0 r16554-
1d4dea6d4f)) #0 Sat Apr 16 12:59:34 2022
[ 0.000000] SoC Type: Ralink RT3883 ver:1 eco:5
[ 0.000000] printk: bootconsolde [early0] enabled
[ 0.000000] CPU0 revision is:
0001974c (MIPS 74Kc)
[ 0.000000] MIPS: machine is D-Link DIR-645
[ 0.000000] Initrd not found or empty - disabling initrd
Using the new seama-lzma-loader it's able to boot OpenWrt 22.03
and OpenWrt SNAPSHOT too:
3: System Boot system code via Flash.
## Booting image at
bc050000 ...
raspi_read: from:50000 len:40
.raspi_read: from:50000 len:c
.raspi_read: from:50000 len:48b004
.........................................................................We have SEAMA, Image Size =
4763588
Verifying Checksum ...
Uncompressing SEAMA linux.lzma ... OK
## Transferring control to Linux (at address
80000000) ...
## Giving linux memsize in MB, 64
Starting kernel ...
OpenWrt kernel loader for MIPS based SoC
Copyright (C) 2011 Gabor Juhos <juhosg@openwrt.org>
Decompressing kernel... done!
Starting kernel at
80000000...
[ 0.000000] Linux version 5.10.144 (xabolcs@ut2004) (mipsel-openwrt-linux-musl-gcc (OpenWrt GCC 11.3.0 r20774+2-
b71affaf8b) 11.3.0, GNU ld (GNU Binutils) 2.37) #0 Tue Sep 27 23:02:30 2022
[ 0.000000] SoC Type: Ralink RT3883 ver:1 eco:5
[ 0.000000] printk: bootconsole [early0] enabled
[ 0.000000] CPU0 revision is:
0001974c (MIPS 74Kc)
[ 0.000000] MIPS: machine is D-Link DIR-645
[ 0.000000] Initrd not found or empty - disabling initrd
[ 0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
[ 0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
[ 0.000000] Zone ranges:
[ 0.000000] Normal [mem 0x0000000000000000-0x0000000003ffffff]
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x0000000000000000-0x0000000003ffffff]
[ 0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x0000000003ffffff]
[ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 16256
[ 0.000000] Kernel command line: console=ttyS0,57600 rootfstype=squashfs,jffs2
The OKLI Loader is unable to read the flash on this SoC:
Looking for OpenWrt image... not found! ('0xddbaddba' at 0xbc051000)
0: https://forum.openwrt.org/t/136435
Fixes: GitHub issue #10634 ("V22.03.0 release currently does not work on D-Link DIR-645")
Fixes: 09faa73c53bd ("ramips: rt3883: use lzma-loader for DIR-645")
Tested-by: Glenn Fowler <gfowler1@outlook.com>
Signed-off-by: Szabolcs Hubai <szab.hu@gmail.com>
Szabolcs Hubai [Mon, 26 Sep 2022 06:42:54 +0000 (08:42 +0200)]
ramips: define lzma-loader recipe for SEAMA devices
Define "Device/seama-lzma-loader" recipe for SEAMA devices to help
contributors avoid doing recipe mistakes.
In a forum topic [0] I was under the impression that the good old
uimage-lzma-loader didn't fix the LZMA ERROR 1 for a device.
It was found out, that the uimage-lzma-loader never worked because the
KERNEL variable was overriden earlier (also an LZMA ERROR 1 related
commit,
6fba88de1913), and the "use lzma-loader" fix (commit
09faa73c53bd) didn't catch that to include the "loader-kernel" part.
I contributed an LZMA ERROR 1 fix (commit
ce1957100411) for the SEAMA
device D-Link DIR-860L B1, where I had to duplicate the whole
uimage-lzma-loader recipe because of the special needs of the vendor
bootloader.
This new recipe reuse most of uimage-lzma-loader's KERNEL definiton to
avoid duplication.
It uses "relocate-kernel" as it needed for D-Link DIR-860L B1 to
boot from flash, and it's compatible with D-Link DIR-645 too.
It repacks lzma-loader with lzma for kernel (without uImage), because
these weird hacked vendor bootloaders accepts only LZMA compressed
kernels from flash:
We have SEAMA, Image Size =
4759794
Verifying Checksum ...
Uncompressing SEAMA linux.lzma ... OK
It uses uImage header for initramfs kernel to be little bit verbose.
0: https://forum.openwrt.org/t/136435/10
Signed-off-by: Szabolcs Hubai <szab.hu@gmail.com>
Arne Zachlod [Sat, 6 Aug 2022 13:35:15 +0000 (15:35 +0200)]
ramips: add support for Mikrotik LtAP-2HnD
Mikrotik LtAP-2HnD is a outdoor/automotive WLAN 4 router with integrated GPS
receiver and two mPCIe slots.
Specifications:
* SoC: MT7621A
* RAM: 128 MiB Nanya NT5CC64M16GP-DI
* Flash: 16 MiB winbond W25Q128JV
* WLAN:
* Atheros AR9382 with power amplifier SKY 85330 (2x2 internal antennas,
with RF switches for external connectors)
* Ethernet: 1 Gbps, single port
* USB Host: USB 2.0 Speeds
* Serial: 115200 baud
* LEDs: Power, System, GPS, 5* RSSI
* mPCIe:
* miniPCIe slot 1: PCIe and USB 2.0 Host (via switch shared with USB Host)
* miniPCIe slot 2: USB 2.0 and 3.0
* SIM Cards:
* Slot 1 Connected to mPCIe slot 1
* Slot 2 and 3 connected to mPCIe slot 2 via switch
* GPS: MTK 3333 on serial port 2 (/dev/ttyS1), 115200 baud and PPS on gpio 14
gpios are exposed to /sys/class/gpio:
* usb-select: swithes USB 2.0 interface between external port and internal
mPCIe slot 1 default is the external USB interface
* gps-reset: resets the GPS interface chip
* sim-select: switches between sim slot 2 and 3 connected to mPCIe slot 2
* gps-ant-select: switches GPS antenna between internal antenna and SMA
connected antenna
* lte-reset: resets mPCIe slot 2
Flashing:
TFTP boot initramfs image and then perform sysupgrade. Follow common
MikroTik procedure as in https://openwrt.org/toh/mikrotik/common.
Signed-off-by: Arne Zachlod <arne@nerdkeller.org>
Will Moss [Wed, 3 Aug 2022 11:37:47 +0000 (11:37 +0000)]
ath79: fix MAC address assignment for TP-Link ar7241 devices
On TP-Link ar7241 devices LAN and WAN interfaces are swapped. Keeping
that in mind fix MAC address assignment as used in vendor firmware:
LAN MAC - main MAC stored in u-boot and printed on label
WAN MAC - LAN MAC + 1
Signed-off-by: Will Moss <willormos@gmail.com>
Shiji Yang [Mon, 24 Oct 2022 04:01:12 +0000 (12:01 +0800)]
ath79: move usb led trigger node to SoC dtsi
These frequently used usb led triggers are universal. They should be
moved to SoC dtsi.
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
John Audia [Thu, 10 Nov 2022 20:42:42 +0000 (15:42 -0500)]
kernel: bump 5.10 to 5.10.154
All patches automatically rebased.
Signed-off-by: John Audia <therealgraysky@proton.me>
John Audia [Fri, 11 Nov 2022 04:59:20 +0000 (23:59 -0500)]
kernel: bump 5.15 to 5.15.78
All patches automatically rebased
Build system: x86_64
Build-tested: bcm2711/RPi4B, mt7622/RT3200
Run-tested: bcm2711/RPi4B, mt7622/RT3200
Signed-off-by: John Audia <therealgraysky@proton.me>
Quintin Hill [Tue, 1 Nov 2022 22:41:18 +0000 (22:41 +0000)]
kernel: backport some Bluetooth RTL8761 USB IDs
These USB IDs appear in the 5.15 stable kernel series but not the 5.10
stable series.
Signed-off-by: Quintin Hill <stuff@quintin.me.uk>
Quintin Hill [Sun, 23 Oct 2022 08:22:37 +0000 (09:22 +0100)]
kernel: backport RTL8761B FW name change to v5.10
Make the firmware filenames referenced by the module consistent for
v5.10 and v5.15 kernels. Backport two upstream patches a cleanup commit
and the commit making the change, the former is required for the latter
to apply cleanly.
Signed-off-by: Quintin Hill <stuff@quintin.me.uk>
Quintin Hill [Sat, 22 Oct 2022 07:15:57 +0000 (08:15 +0100)]
linux-firmware: add rtl8761 bluetooth firmware
Realtek bluetooth devices need firmware. Add packages for some of
these.
Tested on a WNDR3700v4 with rtl8761bu firmware.
Signed-off-by: Quintin Hill <stuff@quintin.me.uk>
Quintin Hill [Sat, 22 Oct 2022 07:14:42 +0000 (08:14 +0100)]
kernel: support for Realtek USB bluetooth devices
USB adaptors with the RTL8761B chipset are cheap and readily available
but so far support is missing in Openwrt. Enable the relevant kernel
options and add a module to the kmod-bluetooth package. Increases size
of kmod-bluetooth ipk from 279140 bytes to 285320 bytes on my ath79 build.
Tested on a WNDR3700v4 with rtl8761bu firmware.
Signed-off-by: Quintin Hill <stuff@quintin.me.uk>
Chen Minqiang [Mon, 7 Nov 2022 08:20:15 +0000 (16:20 +0800)]
dnsmasq: add support for filter-AAAA/A
This add --filter-A and --filter-AAAA options, to remove IPv4 or IPv6
addresses from DNS answers. these options is supported since version 2.87.
Co-authored-by: NueXini <nuexini@alumni.tongji.edu.cn>
Signed-off-by: Chen Minqiang <ptpt52@gmail.com>
Nick Hainke [Thu, 10 Nov 2022 15:24:40 +0000 (16:24 +0100)]
libnftnl: update to 1.2.4
Release Announcement:
https://lore.kernel.org/netfilter-devel/Y20W+LT%2F+sq%2Fi2rz@salvia/T/#u
Signed-off-by: Nick Hainke <vincent@systemli.org>
Nick Hainke [Sat, 12 Nov 2022 09:02:37 +0000 (10:02 +0100)]
linux-firmware: update to
20221109
Changes:
712460c linux-firmware: Update firmware file for Intel Bluetooth 9462
90d5f7e linux-firmware: Update firmware file for Intel Bluetooth 9462
48954ba linux-firmware: Update firmware file for Intel Bluetooth 9560
0e205fd linux-firmware: Update firmware file for Intel Bluetooth 9560
06b941e linux-firmware: Update firmware file for Intel Bluetooth AX201
ba958ff linux-firmware: Update firmware file for Intel Bluetooth AX201
02bdea2 linux-firmware: Update firmware file for Intel Bluetooth AX211
7044d46 linux-firmware: Update firmware file for Intel Bluetooth AX211
1b99bcd linux-firmware: Update firmware file for Intel Bluetooth AX210
4668ae9 linux-firmware: Update firmware file for Intel Bluetooth AX200
5bdfdba linux-firmware: Update firmware file for Intel Bluetooth AX201
b0f995c amdgpu: update DMCUB firmware for DCN 3.1.6
d991031 rtl_bt: Update RTL8822C BT UART firmware to 0xFFB8_ABD6
fd62f01 rtl_bt: Update RTL8822C BT USB firmware to 0xFFB8_ABD3
b15fc21 WHENCE: mrvl: prestera: Add WHENCE entries for newly updated 4.1 FW images
bf5a337 mrvl: prestera: Update Marvell Prestera Switchdev FW to v4.1
4a733c2 iwlwifi: add new FWs from core74_pv-60 release
7d2bb50 qcom: drop split a530_zap firmware file
7d56713 qcom/vpu-1.0: drop split firmware in favour of the mbn file
1431496 qcom/venus-4.2: drop split firmware in favour of the mbn file
cf95783 qcom/venus-4.2: replace split firmware with the mbn file
1fe6f49 qcom/venus-1.8: replace split firmware with the mbn file
abc0302 linux-firmware: Add firmware for Cirrus CS35L41 on new ASUS Laptop
20d9516 iwlwifi: add new PNVM binaries from core74-44 release
06dbfbc iwlwifi: add new FWs from core69-81 release
05df8e6 qcom: update venus firmware files for VPU-2.0
cd6fcdb qcom: remove split SC7280 venus firmware images
1612706 qcom: update venus firmware file for v5.4
ad9fdba qcom: replace split SC7180 venus firmware images with symlink
dae5d46 rtw89: 8852b: update fw to v0.27.32.1
a8e86ec rtlwifi: update firmware for rtl8192eu to v35.7
9aa8db1 rtlwifi: Add firmware v4.0 for RTL8188FU
8f86b5a i915: Add HuC 7.10.3 for DG2
48407ff cnm: update chips&media wave521c firmware.
bd31846 brcm: add symlink for Pi Zero 2 W NVRAM file
771968c linux-firmware: Add firmware for Cirrus CS35L41 on ASUS Laptops
6f9620e linux-firmware: Add firmware for Cirrus CS35L41 on Lenovo Laptops
1d18cb9 linux-firmware: Add firmware for Cirrus CS35L41 on HP Laptops
e497757 rtw89: 8852b: add initial fw v0.27.32.0
98b5577 iwlwifi: add new FWs from core72-129 release
604026c iwlwifi: update 9000-family firmwares to core72-129
Signed-off-by: Nick Hainke <vincent@systemli.org>
Rafał Miłecki [Sat, 12 Nov 2022 09:42:51 +0000 (10:42 +0100)]
kernel: update U-Boot nvmem driver to v6.2 release version
Backport queued patches that
1. Fix CRC32 calculation for redundant images
2. Fix CRC32 on big-endian
3. Fix parting images with Broadcom header
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Felix Fietkau [Fri, 11 Nov 2022 19:03:45 +0000 (20:03 +0100)]
mt76: update to the latest version
8cc34bdc9ef0 wifi: mt76: mt7921: set MT_DRV_AMSDU_OFFLOAD for USB/SDIO
2182de50a37c wifi: mt76: fix receiving LLC packets on mt7615/mt7915
269df4b01f27 wifi: mt76: fix rx checksum offload on mt7615/mt7915/mt7921
fa4ace8e3b58 ieee80211: add EHT 1K aggregation definitions
176df35e7e80 wifi: mt76: mt7915: improve accuracy of time_busy calculation
94b335fa88e1 wifi: mt76: mt7915: add ack signal support
3365c129f73c wifi: mt76: mt7915: enable use_cts_prot support
ad9bd2ba361e wifi: mt76: mt7615: enable use_cts_prot support
68bdcccb0aa7 wifi: mt76: mt7915: fix reporting of TX AGGR histogram
242fece4323f wifi: mt76: mt7921: fix reporting of TX AGGR histogram
75003c69a9bd wifi: mt76: mt7615: rely on mt7615_phy in mt7615_mac_reset_counters
65c70a32f1cf wifi: mt76: move aggr_stats array in mt76_phy
b1ddf8bec058 wifi: mt76: mt7915: rework mt7915_dma_reset()
1ad31c3f76f4 wifi: mt76: mt7915: enable full system reset support
6b0668de7a53 wifi: mt76: mt7915: add full system reset into debugfs
a5e48378d2a6 wifi: mt76: mt7915: enable coredump support
1e9060420c92 wifi: mt76: mt7915: fix incorrect tx path number configuration
0263711ba362 wifi: mt76: mt7915: fix antenna selection with bad eeprom.
869815e5ef86 wifi: mt76: mt7915: Fix chainmask calculation on mt7915 DBDC
fc410557b7e1 wifi: mt76: mt7915: Fix VHT beamforming capabilities with DBDC
daa30a31cf70 wifi: mt76: mt7915: don't claim 160MHz support with mt7915 DBDC
80bcecdbc2ff wifi: mt76: connac: update nss calculation in txs
465219c1f56c wifi: mt76: do not run mt76u_status_worker if the device is not running
c7db15903e5c wifi: mt76: connac: add mt76_connac_mcu_uni_set_chctx
7a2b1a13b1b0 wifi: mt76: mt7921: add chanctx parameter to mt76_connac_mcu_uni_add_bss signature
dece6921e606 wifi: mt76: mt7921: add unified ROC cmd/event support
d4da182389b6 wifi: mt76: mt7921: drop ieee80211_[start, stop]_queues in driver
0c3ef988d8dc wifi: mt76: connac: accept hw scan request at a time
c477225fd10e mt7615: update cr4 firmware to
20190415154149
413a4bf39513 mt76: mt7915: fix unused-but-set variable
f5034abea899 mt76: mt7915: fix format string
a9ac73ed8275 wifi: mt76: mt7615: increase eeprom size for mt7663
4a27f23fc4f2 linux-firmware: update firmware for MT7921 WiFi device
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Rafał Miłecki [Fri, 11 Nov 2022 16:04:18 +0000 (17:04 +0100)]
bcm4908: refresh kernel 5.15 config
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Rafał Miłecki [Fri, 11 Nov 2022 15:51:29 +0000 (16:51 +0100)]
bcm4908: prepare support for kernel 5.15
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Rafał Miłecki [Fri, 11 Nov 2022 13:54:46 +0000 (14:54 +0100)]
bcm4908: update DTS files with the latest changes
The most affecting change is move of files from bcm4908/ to the bcmbca/.
That required updating few paths.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Daniel Golle [Thu, 10 Nov 2022 20:34:15 +0000 (20:34 +0000)]
procd: update to git HEAD
24f6bc4 jail: correctly check for null pointer
93b2c2d jail: ignore missing .dynamic sect
039b88f sysupgrade: print errno on failure
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Daniel Golle [Thu, 10 Nov 2022 14:16:32 +0000 (14:16 +0000)]
ath79: add support for Teltonika RUT300
Add support for the Teltonika RUT300 rugged industrial Ethernet router
Hardware
--------
SoC: Qualcomm Atheros QCA9531
RAM: 64M DDR2 (EtronTech EM68B16CWQK-25IH)
FLASH: 16M SPI-NOR (Winbond W25Q128)
ETH: 4x 100M LAN (QCA9533 internal AR8229 switch, eth0)
1x 100M WAN (QCA9533 internal PHY, eth1)
UART: 115200 8n1, same debug port as other Teltonika devices
USB: 1 single USB 2.0 host port
BUTTON: Reset
LED: 1x green power LED (always on)
5x yellow Ethernet port LED (controlled by Linux)
WAN port LED is used as boot status and upgrade indicator as
the power LED cannot be controlled in software.
Use the *-factory.bin file to intially flash the device using the
vendor firmware's Web-UI.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Felix Fietkau [Thu, 10 Nov 2022 21:24:54 +0000 (22:24 +0100)]
kernel: more fixes for mtk_eth_soc performance optimization
- fix features sync between netdevs
- fix crash in dsa_switch_rcv
Fixes: ceb1451c10c1 ("kernel: add mediatek soc ethernet performance improvements")
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Felix Fietkau [Thu, 10 Nov 2022 13:46:21 +0000 (14:46 +0100)]
mac80211: fix mesh airtime link metric estimation
fix reading the per-packet rate on devices with firmware rate control
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Rafał Miłecki [Thu, 10 Nov 2022 12:58:19 +0000 (13:58 +0100)]
fstools: update to git HEAD
3affe9e block: try multiple NTFS filesystem implementations
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Felix Fietkau [Thu, 10 Nov 2022 12:20:55 +0000 (13:20 +0100)]
kernel: fix vlan parsing issue in mediatek ethernet driver
Check the vlan rx offload flag
Sync features across netdevs
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Felix Fietkau [Thu, 10 Nov 2022 12:08:28 +0000 (13:08 +0100)]
hostapd: remove invalid dtim_period option processing
dtim_period is a bss property, not a device one.
It is already handled properly in mac80211.sh
Fixes: 30c64825c7ed ("hostapd: add dtim_period, local_pwr_constraint, spectrum_mgmt_required")
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Rafał Miłecki [Tue, 8 Nov 2022 11:22:51 +0000 (12:22 +0100)]
kernel: support "linux,rootfs" DT property for splitting rootfs
OpenWrt's support for splitting rootfs (to create an extra "rootfs_data"
partition) is limited to partitions called "rootfs". Upstream kernel
allows any name partition to be rootfs if it has "linux,rootfs" property
set. Add split support to such partitions in OpenWrt code.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Rafał Miłecki [Thu, 10 Nov 2022 08:28:23 +0000 (09:28 +0100)]
bcm53xx: update DTS files with the latest changes
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Weiping Yang [Mon, 19 Sep 2022 09:47:40 +0000 (05:47 -0400)]
ipq40xx: add support for GL.iNet GL-A1300
Specifications:
SOC: Qualcomm IPQ4018 (DAKOTA) ARM Quad-Core
RAM: 256 MiB
FLASH1: 4 MiB NOR
FLASH2: 128 MiB NAND
ETH: Qualcomm QCA8075
WLAN1: Qualcomm Atheros QCA4018 2.4GHz 802.11b/g/n 2x2
WLAN2: Qualcomm Atheros QCA4018 5G 802.11n/ac W2 2x2
USB: 1 x USB 3.0 port
Button: 1 x Reset button
Switch: 1 x Mode switch
LED: 1 x Blue LED + 1 x White LED
Install via uboot tftp or uboot web failsafe.
By uboot tftp:
(IPQ40xx) # tftpboot 0x84000000 openwrt-ipq40xx-generic-glinet_gl-a1300-squashfs-nand-factory.ubi
(IPQ40xx) # nand erase 0 0x8000000
(IPQ40xx) # nand write 0x84000000 0 $filesize
By uboot web failsafe:
Push the reset button for 10 seconds util the power led flash faster,
then use broswer to access http://192.168.1.1
Afterwards upgrade can use sysupgrade image.
Signed-off-by: Weiping Yang <weiping.yang@gl-inet.com>
Edward Chow [Sat, 5 Nov 2022 06:29:03 +0000 (14:29 +0800)]
ath79: calibrate TL-WDR4900 v2 with nvmem-cells
Driver for both soc (2.4GHz Wifi) and pci (5 GHz) now pull the calibration
data from the nvmem subsystem.
This allows us to move the userspace caldata extraction for the pci-e ath9k
supported wifi into the device-tree definition of the device.
wmac's nodes are also changed over to use nvmem-cells over OpenWrt's
custom mtd-cal-data property.
Signed-off-by: Edward Chow <equu@openmail.cc>
Shiji Yang [Thu, 27 Oct 2022 05:17:12 +0000 (13:17 +0800)]
ath79: add missing clock name strings in SoC dtsi
For all SoC in the ath79 target, the PLL controller provides 3 main
clocks "cpu", "ddr" and "ahb" through the input clock "ref".
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
Shiji Yang [Sat, 8 Oct 2022 08:06:00 +0000 (16:06 +0800)]
ath79: move reference clock node to SoC dtsi
AR7161, AR724x, AR9132 and QCA95xx only support fixed frequency external
crystal oscillator, so move reference clock node to SoC dtsi files.
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
Christian Marangi [Wed, 9 Nov 2022 21:28:53 +0000 (22:28 +0100)]
Revert "build: fix for sourcing target image config a when target is being replaced"
This reverts commit
ce1346a8fc0ce9640a4ecbc37bc1686a25c1165d.
Seems to cause buildbot compilation to fail and require more testing.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Prasun Maiti [Wed, 12 Oct 2022 08:32:43 +0000 (14:02 +0530)]
build: fix for sourcing target image config a when target is being replaced
Sourcing of image/Config.in will not happen
When a target is installed from target/linux/feeds/
Signed-off-by: Prasun Maiti <prasunmaiti87@gmail.com>
Felix Fietkau [Wed, 12 Oct 2022 10:54:30 +0000 (12:54 +0200)]
mac80211: remove old legacy legacy drivers
Get rid of drivers that are either limited to 802.11b/g or don't even support
cfg80211/mac80211. Most of these are either limited to boards that we don't even
support anymore because of firmware size, or were only used for custom hacks by
a really small number of users in the past.
Let's get rid of those to reduce the maintenance effort and the number of useless
packages
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Felix Fietkau [Sun, 30 Oct 2022 17:23:00 +0000 (18:23 +0100)]
mediatek: filogic: enable maxlinear PHY support, refresh config
Needed for the 7986 RFB1 board
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Felix Fietkau [Sun, 30 Oct 2022 06:15:36 +0000 (07:15 +0100)]
mediatek: filogic: fix mt7986a ethernet devicetree entries
Add all ports, rename DSA ports to start at lan1
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Felix Fietkau [Sat, 29 Oct 2022 21:03:08 +0000 (23:03 +0200)]
mediatek: drop the use of device tree overlays on mt7986a-rfb board
The boot loader does not support it. Instead make NAND the default image for
this board
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Felix Fietkau [Sat, 29 Oct 2022 17:01:48 +0000 (19:01 +0200)]
scripts/mkits.sh: fix portability issue
BSD wc can output more whitespaces, which breaks the cut usage.
Replace the cut invocation with awk, which is more portable.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Andrew Powers-Holmes [Tue, 1 Nov 2022 06:06:32 +0000 (17:06 +1100)]
mt76: add firmware package for mt7916
Add kernel package 'mt7916-firmware' with firmware files for MT7916E devices.
These share the same driver as the MT7915 chipset, but use their own firmware.
Tested using a pair of AsiaRF AW7916-NPD cards.
Signed-off-by: Andrew Powers-Holmes <aholmes@omnom.net>
Felix Fietkau [Fri, 28 Oct 2022 11:15:37 +0000 (13:15 +0200)]
kernel: add mediatek soc ethernet performance improvements
- implement multiqueue via qdma hardware shaper to deal with ports with different speeds
- implement hardware DSA untagging
- add NETIF_F_ALL_TSO to reduce unnecessary segmentation
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Nick Hainke [Sun, 6 Nov 2022 15:48:32 +0000 (16:48 +0100)]
mac80211: subsys: add tags to upstreamed patches
Some patches were already upstreamed.
Signed-off-by: Nick Hainke <vincent@systemli.org>
Nick Hainke [Sun, 6 Nov 2022 15:05:44 +0000 (16:05 +0100)]
mac80211: rt2x00: add tags to upstreamed patches
Some patches are already upstreamed.
Signed-off-by: Nick Hainke <vincent@systemli.org>
Nick Hainke [Sun, 6 Nov 2022 14:48:45 +0000 (15:48 +0100)]
mac80211: brcm: add tag to upstreamed patch
Add tag to upstreamed patch.
Signed-off-by: Nick Hainke <vincent@systemli.org>
Nick Hainke [Sun, 6 Nov 2022 14:37:05 +0000 (15:37 +0100)]
mac80211: ath9k: add tag to upstreamed patch
Add tag to upstreamed patch.
Signed-off-by: Nick Hainke <vincent@systemli.org>
Nick Hainke [Sun, 6 Nov 2022 14:14:58 +0000 (15:14 +0100)]
mac80211: ath10k: add tags for upstreamed patches
Add tags to already upstreamed patches.
Signed-off-by: Nick Hainke <vincent@systemli.org>
Edward Matijevic [Sun, 6 Nov 2022 19:12:36 +0000 (13:12 -0600)]
ipq806x: kernel ramoops storage for C2600/AD7200
Define the kernel crash log storage ramoops/pstore feature
for C2600/AD7200 and add kmod-ramoops to default.
Tested with C2600 only.
Signed-off-by: Edward Matijevic <motolav@gmail.com>
David Bauer [Sun, 6 Nov 2022 23:42:57 +0000 (00:42 +0100)]
ramips: define loadaddr for U6 Lite DTB
The Ubiquiti UniFi 6 Lite does not correctly align the FDT by always
setting fdt_high to 0xffffffff when invoking the bootubnt command.
Work around this issue by loading the DTB to a valid,aligned address, so
the bootloader does not have to relocate the FDT automatically.
Note: The device does read the kernel before invoking bootm on the FIT
image to 0x86000000.
Signed-off-by: David Bauer <mail@david-bauer.net>
David Bauer [Sun, 6 Nov 2022 23:42:40 +0000 (00:42 +0100)]
mkits: support definition of DTB loadaddr
Support defining a per-device loadaddress for the DTB. This is required
for devices which to not align the DTB from the bootloader correctly.
Signed-off-by: David Bauer <mail@david-bauer.net>
Rafał Miłecki [Wed, 2 Nov 2022 19:26:33 +0000 (20:26 +0100)]
kernel: improve description of NTFS kernel packages
This helps choosing the right NTFS driver from two available options.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Rafał Miłecki [Mon, 7 Nov 2022 18:24:48 +0000 (19:24 +0100)]
kernel: backport support for "linux,rootfs" in DT
This DT property allows marking flash partition that Linux should use as
a root device. It's useful for devices that don't use U-Boot and cmdline
parser for partitioning. It may be used with "fixed-partitions" or some
dynamic partitioning based on flash content.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Rafał Miłecki [Mon, 7 Nov 2022 22:39:52 +0000 (23:39 +0100)]
kernel: split out mtd hack for CONFIG_FIT_PARTITION + rootfs
This is some hack on top of our old hack. Use separated patch for it so
it's easier to understand and actually possible to describe. We should
ideally get rid of this (and we actually did with kernels 5.15+).
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Michael Lyle [Sun, 30 Oct 2022 04:00:41 +0000 (21:00 -0700)]
ramips: gl-mt1300: downclock SPI to 50MHz
The SPI max frequency was set to 80MHz, considerably higher than the
vendor clocks it in their firmware (10MHz). Multiple users reported
jffs2 corruption/instability in GitHub issue #10461.
My unit has a W25Q256; datasheet specifies maximum SPI frequency for
read command of 50MHz.
Thanks to @DragonBlueP for suggesting to eliminate m25p,fast-read;
and @MPannen1979 for identifying the problem.
Fixes: #10461
Signed-off-by: Michael Lyle <mlyle@lyle.org>
Sungbo Eo [Sun, 20 Feb 2022 01:20:35 +0000 (10:20 +0900)]
ramips: fix TP-Link RE200 v3/v4 LEDs
Set power LED to gpio 43 instead of 44 for v3 and v4.
Set red wifi LED to gpio 40 (was assigned to `red:wifi5g`).
Tested by the author of the initial v3 and v4 commit.
Reported-by: Richard Fröhning <misanthropos@gmx.de>
Tested-by: Richard Fröhning <misanthropos@gmx.de>
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
Signed-off-by: Jan-Niklas Burfeind <git@aiyionpri.me>
Kevin Darbyshire-Bryant [Sun, 6 Nov 2022 20:38:23 +0000 (20:38 +0000)]
dnsmasq: remove backported CVE patch
Patch no longer applies/required since bump to v2.87
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
Kevin Darbyshire-Bryant [Mon, 29 Nov 2021 17:16:39 +0000 (17:16 +0000)]
dnsmasq: Support nftables nftsets
Add build option for nftables sets. By default disable iptables ipset
support. By default enable nftable nftset support since this is what
fw4 uses.
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
dnsmasq: nftset: serve from ipset config
Use existing ipset configs as source for nftsets to be compatible with
existing configs. As the OS can either have iptables XOR nftables
support, it's fine to provide both to dnsmasq. dnsmasq will silently
fail for the present one. Depending on the dnsmasq compile time options,
the ipsets or nftsets option will not be added to the dnsmasq config
file.
dnsmasq will try to add the IP addresses to all sets, regardless of the
IP version defined for the set. Adding an IPv6 to an IPv4 set and vice
versa will silently fail.
Signed-off-by: Mathias Kresin <dev@kresin.me>
dnsmasq: support populating nftsets in addition to ipsets
Tell dnsmasq to populate nftsets instead of ipsets, if firewall4 is present in
the system. Keep the same configuration syntax in /etc/config/dhcp, for
compatibility purposes.
Huge thanks to Jo-Philipp Wich for basically writing the function.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
dnsmasq: obtain nftset ip family from nft
Unfortunately dnsmasq nft is noisy if an attempt to add a mismatched ip address
family to an nft set is made.
Heuristic to guess which ip family a nft set might belong by inferring
from the set name.
In order of preference:
If setname ends with standalone '4' or '6' use that, else
if setname has '4' or '6' delimited by '-' or '_' use that (eg
foo-4-bar) else
If setname begins with '4' or '6' standalone use that.
By standalone I mean not as part of a larger number eg. 24
If the above fails then use the existing nft set query mechanism and if
that fails, well you're stuffed!
With-thanks-to: Jo-Philipp Wich <jo@mein.io> who improved my regexp
knowledge.
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
dnsmasq: specify firewall table for nftset
Permit ipsets to specify an nftables table for the set. New config
parameter is 'table'. If not specified the default of 'fw4' is used.
config ipset
list name 'BK_4,BK_6'
option table 'dscpclassify'
option table_family 'ip'
option family '4'
list domain 'ms-acdc.office.com'
list domain 'windowsupdate.com'
list domain 'update.microsoft.com'
list domain 'graph.microsoft.com'
list domain '1drv.ms'
list domain '1drv.com'
The table family can also be specified, usually 'ip' or 'ip6' else the
default 'inet' capable of both ipv4 & ipv6 is used.
If the table family is not specified then finally a family option is
available to specify either '4' or '6' for ipv4 or ipv6 respectively.
This is all in addition to the existing heuristic that will look in the
nftset name for an ip family clue, or in total desperation, query the
value from the nftset itself.
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
Mathias Kresin [Wed, 4 May 2022 19:50:41 +0000 (21:50 +0200)]
dnsmasq: add uci-defaults script for ipset migration
When running sysupgrade from an existing configuration, move existing
ipset definitions to a dedicated config section. Later on, it will allow
to serve ipset as well as nftable sets from the same configuration.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Kevin Darbyshire-Bryant [Wed, 15 Sep 2021 20:15:33 +0000 (21:15 +0100)]
dnsmasq: bump to 2.87
Bump dnsmasq to 2.87 & refresh patches
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
Kuan-Yi Li [Fri, 4 Nov 2022 16:16:36 +0000 (00:16 +0800)]
sdk: use git-src-full to allow Git versioning
$(AUTORELEASE) uses Git log to determine releases and package timestamps.
Base feed is shallow cloned by default in generated SDK, resulting in
an incomplete Git log and therefore different local package versions than
offered upstream.
This patch complements commit
7fae1e5677 by setting the base feed to use
`src-git-full` to solve that.
Signed-off-by: Kuan-Yi Li <kyli@abysm.org>
Alan Luck [Fri, 14 Oct 2022 06:26:27 +0000 (17:26 +1100)]
ath79: expand rootfs for DIR-825-B1 with unused space
Expand currently unused flash space to roofs for DIR-825-B1 by using the same
flash space as the old ar71xx big image without moving the caldata.
With some testing this partition is use by the OEM firmware
but if changed is regenerated which allows reverting to OEM firmware
Signed-off-by: Alan Luck <luckyhome2008@gmail.com>
Korey Caro [Sun, 13 Mar 2022 04:36:30 +0000 (23:36 -0500)]
ath79: add support to TrendNet TEW-673GRU
Add support for the TrendNet TEW-673GRU to ath79.
This device was supported in 19.07.9 but was deprecated with ar71xx.
This is mostly a copy of D-Link DIR-825 B1.
Updates have been completed to enable factory.bin and sysupgrade.bin both.
Code improvements to DTS file and makefile.
Architecture | MIPS
Vendor | Qualcomm Atheros
bootloader | U-Boot
System-On-Chip | AR7161 rev 2 (MIPS 24Kc V7.4)
CPU/Speed | 24Kc V7.4 680 MHz
Flash-Chip | Macronix MX25L6405D
Flash size | 8192 KiB
RAM Chip: | ProMOS V58C2256164SCI5 × 2
RAM size | 64 MiB
Wireless | 2 x Atheros AR922X 2.4GHz/5.0GHz 802.11abgn
Ethernet | RealTek RTL8366S Gigabit w/ port based vlan support
USB | Yes 2 x 2.0
Initial Flashing Process:
1) Download 22.03 tew-673gru factory bin
2) Flash 22.03 using TrendNet GUI
OpenWRT Upgrade Process
3) Download 22.03 tew-673gru sysupgrade.bin
4) Flash 22.03 using OpenWRT GUI
Signed-off-by: Korey Caro <korey.caro@gmail.com>
Hauke Mehrtens [Wed, 2 Nov 2022 21:17:51 +0000 (22:17 +0100)]
CI: packages.yml: Fix usage of pre-build tools
Activate CONFIG_AUTOREMOVE to match the settings used to build the
pre-build tools. This has to match the pre-build tools to not rebuild
them.
This prevents the tools being rebuild in packages.yml.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Linos Giannopoulos [Sun, 2 Oct 2022 22:30:28 +0000 (01:30 +0300)]
ramips: add support for TP-Link MR600 V2(EU)
MR600 V2(EU) is an LTE router that also supports 4G+ band aggregation
etc. and can reportedly achieve higher bandwidth with it.
- Specifications:
* SoC: Mediatek MT7621DAT 880MHz
* RAM: 128MB DDR3
* Flash: 16MB SPI NOR flash (GD25Q128C)
* LTE Modem: Qualcomm MDM9240
* WiFi 5GHz: Mediatek MT7613BEN
* WiFi 2.4GHz: Mediatek MT7603EN
* Ethernet: MT7530, 4x 1000Base-T.
* UART: Serial console (115200 8n1), J1(GND:3)
* Buttons: Reset, WPS.
* LED: Power, WAN, LTE, WiFi 2GHz and 5GHz, LAN, Signal1, Signal2,
Signal3
- MAC Addresses:
OEM firmware configuration:
54:af:97:xx:xx:7b : 2.4G
54:af:97:xx:xx:7a : 5G
54:af:97:xx:xx:7c : LTE
54:af:97:xx:xx:7b : LAN (label)
54:af:97:xx:xx:7c : WAN
- Installation:
1. Download the OpenWrt initramfs-image.
Place it into a TFTP server root directory and rename it to openwrt.img
Configure the TFTP server to listen at 192.168.0.5/24.
3. Connect to the serial console.
Attach power and interrupt the boot procedure when prompted (type `tpl`).
Credentials are admin / 1234
4. Configure U-Boot for booting OpenWrt from ram
$ tftpboot
$ bootm
5. Transfer the OpenWrt sysupgrade image to the device.
- LTE:
In order to setup the wwan0 interface:
1. Add a `qmi` proto interface under `/etc/config/network`, e.g.:
```
config interface 'wwan0'
option device '/dev/cdc-wdm0'
option proto 'qmi'
option pincode 'XXXX'
option apn 'your_isp_apn'
```
2. Add `wwan0` interface to the `wan` firewall zone
3. `/etc/init.d/network restart`
Signed-off-by: Linos Giannopoulos <linosgian00@gmail.com>
Shiji Yang [Thu, 15 Sep 2022 17:10:52 +0000 (01:10 +0800)]
ramips: add support for SIM SIMAX1800T and Haier HAR-20S2U1
SIM AX18T and Haier HAR-20S2U1 Wi-Fi6 AX1800 routers are designed based
on Tenbay WR1800K. They have the same hardware circuits and u-boot.
SIM AX18T has three carrier customized models: SIMAX1800M (China Mobile),
SIMAX1800T (China Telecom) and SIMAX1800U (China Unicom). All of these
models run the same firmware.
Specifications:
SOC: MT7621 + MT7905 + MT7975
ROM: 128 MiB
RAM: 256 MiB
LED: status *3 R/G/B
Button: reset *1 + wps/mesh *1
Ethernet: lan *3 + wan *1 (10/100/1000Mbps)
TTL Baudrate: 115200
TFTP Server: 192.168.1.254
TFTP IP: 192.168.1.28 or 192.168.1.160 (when envs is broken)
MAC Address:
use address source
label 30:xx:xx:xx:xx:62 wan
lan 30:xx:xx:xx:xx:65 factory.0x8004
wan 30:xx:xx:xx:xx:62 factory.0x8004 -3
wlan2g 30:xx:xx:xx:xx:64 factory.0x0004
wlan5g 32:xx:xx:xx:xx:64 factory.0x0004 set 7th bit
TFTP Installation (initramfs image only & recommend):
1. Set local tftp server IP: 192.168.1.254 and NetMask: 255.255.255.0
2. Rename initramfs-kernel.bin to "factory.bin" and put it in the root
directory of the tftp server. (tftpd64 is a good choice for Windows)
3. Start the TFTP server, plug in the power supply, and wait for the
system to boot.
4. Backup "firmware" partition and rename it to "firmware.bin", we need
it to back to stock firmware.
5. Use "fw_printenv" command to list envs.
If "firmware_select=2" is observed then set u-boot enviroment:
/# fw_setenv firmware_select 1
6. Apply sysupgrade.bin in OpenWrt LuCI.
Web UI Installation:
1. Apply update by uploading initramfs-factory.bin to the web UI.
2. Use "fw_printenv" command to list envs.
If "firmware_select=2" is observed then set u-boot enviroment:
/# fw_setenv firmware_select 1
3. Apply squashfs-sysupgrade.bin in OpenWrt LuCI.
Recovery to stock firmware:
a. Upload "firmware.bin" to OpenWrt /tmp, then execute:
/# mtd -r write /tmp/firmware.bin firmware
b. We can also write factory image "UploadBrush-bin.img" to firmware
partition to recovery. Upload image file to /tmp, then execute:
/# mtd erase firmware
/# mtd -r write /tmp/UploadBrush-bin.img firmware
How to extract stock firmware image:
Download stock firmware, then use openssl:
openssl aes-256-cbc -d -salt -in [Downloaded_Firmware] \
-out "firmware.tar.tgz" -k QiLunSmartWL
Signed-off-by: Chen Minqiang <ptpt52@gmail.com>
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
Hauke Mehrtens [Tue, 1 Nov 2022 22:18:08 +0000 (23:18 +0100)]
ltq-tapi: Fix compile with kernel 5.15
Do not use find_vpid(), but get_task_pid() to get the pid from
pThrCntrl->tid. This is now a ponter to struct task_struct instead of
an integer.
This fixes the build of ltq-tapi with lantiq/xway.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Hauke Mehrtens [Tue, 1 Nov 2022 22:14:58 +0000 (23:14 +0100)]
ltq-ifxos: Fix compile with ltq-tapi
Do not include asm/irq.h directly, but include linux/interrupt.h instead.
This fixes the build of ltq-tapi with lantiq/xway.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Hauke Mehrtens [Tue, 1 Nov 2022 14:23:17 +0000 (15:23 +0100)]
busybox: awk: fix use after free (CVE-2022-30065)
This backports a commit which fixes a use after free bug in awk.
CVE-2022-30065 description:
A use-after-free in Busybox 1.35-x's awk applet leads to denial of
service and possibly code execution when processing a crafted awk
pattern in the copyvar function.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Hauke Mehrtens [Tue, 1 Nov 2022 14:17:03 +0000 (15:17 +0100)]
dnsmasq: Backport DHCPv6 server fix (CVE-2022-0934)
This backports a commit from upstream dnsmasq to fix CVE-2022-0934.
CVE-2022-0934 description:
A single-byte, non-arbitrary write/use-after-free flaw was found in
dnsmasq. This flaw allows an attacker who sends a crafted packet
processed by dnsmasq, potentially causing a denial of service.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Alexander Horner [Mon, 26 Sep 2022 19:17:40 +0000 (20:17 +0100)]
ramips: add support for Zbtlink ZBT-WG1602-V04
Description heavily based on commit
7e89421a7c3855d66a20350a5bf9ca4cc7a2caf9 by
Sergey Ryazanov <ryazanov.s.a@gmail.com> Details I cannot confirm have
been removed
Completed with great help from \x on IRC. Thanks, \x!
Zbtlink ZBT-WG1602-V04 is a Wi-Fi router intendend for use with WWAN
(UMTS/LTE/3G/4G) modems. The router board offers a couple of miniPCIe
slots with USB and SIM only and another one which is a pure miniPCIe
slot as well as five Gigabit Ethernet ports (4xLAN + WAN).
Specification:
* SoC: MT7621A
* RAM: 256/512 MiB
* Flash: 16/32 MiB
* Eth: 10/100/1000 Mbps Ethernet x5 ports (4xLAN + WAN)
* WLAN 2GHz: MT7603E (.11bgn, MIMO 2x2)
* WLAN 5GHz: MT7662E (.11nac, MIMO 2x2)
* WLAN Ants: detachable x2, shared by 2GHz & 5GHz radios
* miniPCIe: 2x slots with USB&SIM + 1x slot with regular PCIe bus
* WWAN Ants: detachable x4
* External storage: microSD (SDXC) slot
* USB: 3.0 Type-A port
* LED: 11 (5 per Eth phy, 3 SoC controlled, 2 WLAN 2/5 controlled,
1 power indicator)
* Button: 1 (reset)
* UART: console (115200 baud)
* Power: DC jack (12 V / 2.5 A)
Additional HW information:
* SoC USB port 1 is shared by internal miniPCIe slot and external
Type-A USB port, USB D+/D- lines are toggled between ports using a
GPIO controlled DPDT switch.
Installation:
The kernel image can be installed directly onto the device via a browser
to 192.168.1.1 using the built in firmware recovery Web UI available.
It can be accessed by pushing the reset button in, applying power and
holding the reset button for approximately 10 seconds. When the kernel
image has been flashed, you can access LuCI and upload the sysupgrade
as normal.
Signed-off-by: Alexander Horner <ahorner@programmer.net>
Shiji Yang [Sat, 5 Nov 2022 11:52:08 +0000 (19:52 +0800)]
ramips: add support for Youku X2
Specifications:
SOC: MT7620AN + MT7612EN
RAM: 128 MiB DDR2
Flash: 16 MiB (Winbond W25Q28FVFG)
WLAN: 2.4G + 5G
LAN: LAN ports *2
WAN: WAN port *1
USB: USB2.0 *1
SD Card: MicroSD *1
Buttons: Reset *1
LEDs: ethernet *3, system, usb, wlan2g, wlan5g
MAC Address:
use address source
label 54:36:9b:xx:xx:ac lan
lan 54:36:9b:xx:xx:ac factory.0x0028
wan 54:36:9b:xx:xx:ad factory.0x002e
wlan2g 54:36:9b:xx:xx:ae factory.0x0004
wlan5g 54:36:9b:xx:xx:af factory.0x8004
Installation:
1. Apply initramfs-kernel.bin in stock firmware Web UI.
2. Install sysupgrade.bin on OpenWrt and do not retain any configuration.
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
Shiji Yang [Sat, 5 Nov 2022 11:52:08 +0000 (19:52 +0800)]
ramips: improve compatibility for Youku YK-L2 and YK-L1 series
Add UIMAGE_NAME and UIMAGE_MAGIC to allow users to directly install
initramfs-kernel.bin from the stock firmware Web UI. At the same time,
this change makes it possible to boot OpenWrt with the official u-boot.
Notice:
Since the stock firmware is based on OpenWrt and the configuration
will be retained by default during the upgrade process, so we must use
initramfs-kernel.bin to do a initial installation. After the system
restarts, install sysupgrade.bin and do not retain any configuration.
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
Pawel Dembicki [Mon, 24 Oct 2022 13:11:07 +0000 (15:11 +0200)]
uboot-layerscape: adjust LS1012A-IOT config and env
In
a254279a6c30 LS1012A-IOT kernel image was switched to FIT.
But u-boot config is lack of FIT and ext4 support.
This patch enables it.
It also fix envs, because for some reason this board need to use "loadaddr"
variable in brackets.
Fixes: #9894
Fixes: a254279a6c30 ("layerscape: Change to combined rootfs on sd images")
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
Nick Hainke [Mon, 31 Oct 2022 23:36:37 +0000 (00:36 +0100)]
valgrind: update to 3.20.0
Release Notes:
https://valgrind.org/docs/manual/dist.news.html
Signed-off-by: Nick Hainke <vincent@systemli.org>
Martin Schiller [Wed, 2 Nov 2022 06:41:04 +0000 (07:41 +0100)]
kernel: further cleanup of xfrm[4|6]_mode*
In my commit
da5c45f4d886 ("kernel: remove handling of xfrm[4|6]_mode_*
modules") I missed a few default config options and description entries.
Those should be gone as well.
Fixes: da5c45f4d886 ("kernel: remove handling of xfrm[4|6]_mode_* modules")
Signed-off-by: Martin Schiller <ms@dev.tdt.de>
Luiz Angelo Daros de Luca [Thu, 3 Nov 2022 16:34:22 +0000 (13:34 -0300)]
realtek: fix typo in debug message
vid_end was mentioned twice.
Signed-off-by: Luiz Angelo Daros de Luca <luizluca@gmail.com>
John Audia [Thu, 3 Nov 2022 16:07:30 +0000 (12:07 -0400)]
kernel: bump 5.15 to 5.15.77
Manually rebased:
bcm27xx/patches-5.15/950-0600-xhci-quirks-add-link-TRB-quirk-for-VL805.patch
bcm27xx/patches-5.15/950-0606-usb-xhci-add-VLI_TRB_CACHE_BUG-quirk.patch
bcm27xx/patches-5.15/950-0717-usb-xhci-add-a-quirk-for-Superspeed-bulk-OUT-transfe.patch
bcm53xx/patches-5.15/180-usb-xhci-add-support-for-performing-fake-doorbell.patch
lantiq/patches-5.15/0028-NET-lantiq-various-etop-fixes.patch
All other patches automatically rebased
Build system: x86_64
Build-tested: bcm2711/RPi4B, mt7622/RT3200
Run-tested: bcm2711/RPi4B, mt7622/RT3200
Signed-off-by: John Audia <therealgraysky@proton.me>
John Audia [Thu, 3 Nov 2022 16:54:01 +0000 (12:54 -0400)]
kernel: bump 5.10 to 5.10.153
Manually rebased:
bcm53xx/patches-5.10/180-usb-xhci-add-support-for-performing-fake-doorbell.patch
lantiq/patches-5.10/0028-NET-lantiq-various-etop-fixes.patch
All patches automatically rebased.
Signed-off-by: John Audia <therealgraysky@proton.me>
Nick Hainke [Fri, 4 Nov 2022 22:34:02 +0000 (23:34 +0100)]
tools/fakeroot: update to 1.30.1
Release Notes:
https://tracker.debian.org/news/
1381350/accepted-fakeroot-1301-1-source-into-unstable/
Refresh patches:
- 600-macOS.patch
Signed-off-by: Nick Hainke <vincent@systemli.org>
John Audia [Thu, 3 Nov 2022 13:27:49 +0000 (09:27 -0400)]
openssl: bump to 1.1.1s
Changes between 1.1.1r and 1.1.1s [1 Nov 2022]
*) Fixed a regression introduced in 1.1.1r version not refreshing the
certificate data to be signed before signing the certificate.
[Gibeom Gwon]
Changes between 1.1.1q and 1.1.1r [11 Oct 2022]
*) Fixed the linux-mips64 Configure target which was missing the
SIXTY_FOUR_BIT bn_ops flag. This was causing heap corruption on that
platform.
[Adam Joseph]
*) Fixed a strict aliasing problem in bn_nist. Clang-14 optimisation was
causing incorrect results in some cases as a result.
[Paul Dale]
*) Fixed SSL_pending() and SSL_has_pending() with DTLS which were failing to
report correct results in some cases
[Matt Caswell]
*) Fixed a regression introduced in 1.1.1o for re-signing certificates with
different key sizes
[Todd Short]
*) Added the loongarch64 target
[Shi Pujin]
*) Fixed a DRBG seed propagation thread safety issue
[Bernd Edlinger]
*) Fixed a memory leak in tls13_generate_secret
[Bernd Edlinger]
*) Fixed reported performance degradation on aarch64. Restored the
implementation prior to commit
2621751 ("aes/asm/aesv8-armx.pl: avoid
32-bit lane assignment in CTR mode") for 64bit targets only, since it is
reportedly 2-17% slower and the silicon errata only affects 32bit targets.
The new algorithm is still used for 32 bit targets.
[Bernd Edlinger]
*) Added a missing header for memcmp that caused compilation failure on some
platforms
[Gregor Jasny]
Build system: x86_64
Build-tested: bcm2711/RPi4B
Run-tested: bcm2711/RPi4B
Signed-off-by: John Audia <therealgraysky@proton.me>
Nick Hainke [Wed, 2 Nov 2022 15:18:34 +0000 (16:18 +0100)]
elfutils: update to 1.88
Release Notes:
https://sourceware.org/pipermail/elfutils-devel/2022q4/005561.html
Refresh patches:
- 003-libintl-compatibility.patch
- 100-musl-compat.patch
- 101-no-fts.patch
Signed-off-by: Nick Hainke <vincent@systemli.org>
Nick Hainke [Wed, 2 Nov 2022 15:14:22 +0000 (16:14 +0100)]
tools/elfutils: update to 1.88
Release Notes:
https://sourceware.org/pipermail/elfutils-devel/2022q4/005561.html
Signed-off-by: Nick Hainke <vincent@systemli.org>
Nick Hainke [Wed, 2 Nov 2022 15:04:52 +0000 (16:04 +0100)]
strace: update to 6.0
Release Notes:
https://github.com/strace/strace/releases/tag/v6.0
Signed-off-by: Nick Hainke <vincent@systemli.org>
Nick Hainke [Wed, 2 Nov 2022 14:25:36 +0000 (15:25 +0100)]
tools/mtd-utils: update to 2.1.5
Release Notes:
https://lore.kernel.org/buildroot/
c0992bbb-9487-9a51-ea9f-
39cf074b61ec@sigma-star.at/
Refresh patches:
- 130-lzma_jffs2.patch
- 320-mkfs.jffs2-SOURCE_DATE_EPOCH.patch
Signed-off-by: Nick Hainke <vincent@systemli.org>
Nick Hainke [Wed, 2 Nov 2022 14:13:53 +0000 (15:13 +0100)]
tools/mtools: update to 4.0.42
Release Notes:
https://lists.gnu.org/archive/html/info-mtools/2022-10/msg00000.html
Signed-off-by: Nick Hainke <vincent@systemli.org>
Nick Hainke [Thu, 3 Nov 2022 12:48:25 +0000 (13:48 +0100)]
mediatek: replace mt7986 watchdog assert patch with upstream
Replace "920-watchdog-add-mt7986-assert.patch" with upstreamed
- 920-v5.16-watchdog-mtk-add-disable_wdt_extrst-support.patch
- 921-v5.19-watchdog-mtk_wdt-mt7986-Add-toprgu-reset-controller.patch
Signed-off-by: Nick Hainke <vincent@systemli.org>
Nick Hainke [Thu, 3 Nov 2022 12:00:17 +0000 (13:00 +0100)]
mediatek: mt7629: add tag to upstreamed patches
The patches were upstreamed.
Signed-off-by: Nick Hainke <vincent@systemli.org>
Nick Hainke [Thu, 3 Nov 2022 10:41:44 +0000 (11:41 +0100)]
mediatek: add tag for upstreamed patches
The patches were upstreamed.
Signed-off-by: Nick Hainke <vincent@systemli.org>
Nick Hainke [Thu, 3 Nov 2022 10:18:49 +0000 (11:18 +0100)]
mediatek: mt7986: add tag to upstreamed patches
The patch "210-pinctrl-mediatek-add-support-for-MT7986-SoC.patch" and
"212-clk-mediatek-add-mt7986-clock-support.patch" are upstreamed.
Signed-off-by: Nick Hainke <vincent@systemli.org>
Nick Hainke [Thu, 3 Nov 2022 10:02:02 +0000 (11:02 +0100)]
mediatek: mt7622: add tag to upstreamed patches
The patches "191-arm64-dts-mt7622-specify-the-L2-cache-topology.patch"
and "192-arm64-dts-mt7622-specify-the-number-of-DMA-requests.patch" are
upstreamed to 5.19.
Signed-off-by: Nick Hainke <vincent@systemli.org>
Aleksander Jan Bajkowski [Sat, 22 Oct 2022 14:16:14 +0000 (16:16 +0200)]
mediatek: filogic: disable swconfig
This subtarget supports 3 devices:
* Bananapi BPi-R3 (added in
a96382c1bb204698cd43e82193877c10e4b63027),
* MediaTek MTK7986 rfba AP (added in
cffc77ae55ed0e5b9e70417d6a1e1d280cea92cf),
* MediaTek MTK7986 rfbb AP (added in
cffc77ae55ed0e5b9e70417d6a1e1d280cea92cf).
This subtarget supports DSA from the beginning. It looks like CONFIG_SWCONFIG
was copied from another config when the subtarget was created.
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
Aleksander Jan Bajkowski [Sat, 22 Oct 2022 14:13:32 +0000 (16:13 +0200)]
mediatek: filogic: refresh config
This was done by executing these command:
$ time make kernel_oldconfig CONFIG_TARGET=subtarget
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
Glen Huang [Mon, 24 Oct 2022 15:39:55 +0000 (23:39 +0800)]
uhttpd: use procd to reload on acme renew
Calling /etc/init.d/uhttpd reload directly in the acme hotplug script
can inadvertently start a stopped instance.
Signed-off-by: Glen Huang <i@glenhuang.com>
Rafał Miłecki [Thu, 3 Nov 2022 06:37:42 +0000 (07:37 +0100)]
bcm4908: backport upstream BQL support for bcm4908_enet
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Hauke Mehrtens [Wed, 2 Nov 2022 23:20:30 +0000 (00:20 +0100)]
kernel: Refresh generic patches
This patch was out of sync.
Fixes: 1673b7dca384 ("kernel: backport fixes for MediaTek Ethernet driver")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Rafał Miłecki [Wed, 2 Nov 2022 19:09:04 +0000 (20:09 +0100)]
kernel: sort filesystems symbols alphabetically
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Daniel Golle [Wed, 2 Nov 2022 12:41:40 +0000 (12:41 +0000)]
kernel: backport fixes for MediaTek Ethernet driver
Backport patches from net-next which fix possible memory and resource
leaks in the error codepaths of WED initialization.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Daniel Golle [Wed, 2 Nov 2022 11:24:56 +0000 (11:24 +0000)]
kernel: support hw flow-offloading counters on newer MediaTek SoCs
The packet processing engine (PPE) found in newer ARM-based MediaTek
SoCs provides packet and byte counters for offloaded streams.
Import pending patch reading and using those counters.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Daniel Golle [Wed, 2 Nov 2022 11:27:47 +0000 (11:27 +0000)]
mediatek: remove obsolete patch
The patch enabling hardware flow offloading support on the MT7623 SoC
has been merged upstream as of Linux 5.13. Remove our local patch which
wrongly got forward-ported and now actually enables hardware flow
offloading for the MT2701 SoC family (unsupported in OpenWrt).
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Baptiste Jonglez [Wed, 19 Oct 2022 14:49:03 +0000 (16:49 +0200)]
firewall: config: drop input traffic by default
This is necessary with firewall4 to avoid a hard-to-diagnose race
condition during boot, causing DNAT rules not to be taken into account
correctly.
The root cause is that, during boot, the ruleset is mostly empty, and
interface-related rules (including DNAT rules) are added incrementally.
If a packet hits the input chain before the DNAT rules are setup, it can
create buggy conntrack entries that will persist indefinitely.
This new default should be safe because firewall4 explicitly accepts
authorized traffic and rejects the rest. Thus, in normal operations, the
default policy is not used.
Fixes: #10749
Ref: https://github.com/openwrt/openwrt/issues/10749
Signed-off-by: Baptiste Jonglez <git@bitsofnetworks.org>
projects / openwrt / staging / jow.git / log