Amit Cohen [Thu, 18 Apr 2019 07:14:16 +0000 (07:14 +0000)]
mlxsw: spectrum: Fix autoneg status in ethtool
If link is down and autoneg is set to on/off, the status in ethtool does
not change.
The reason is when the link is down the function returns with zero
before changing autoneg value.
Move the checking of link state (up/down) to be performed after setting
autoneg value, in order to be sure that autoneg will change in any case.
Fixes: 56ade8fe3fe1 ("mlxsw: spectrum: Add initial support for Spectrum ASIC")
Signed-off-by: Amit Cohen <amitc@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ido Schimmel [Thu, 18 Apr 2019 07:14:14 +0000 (07:14 +0000)]
mlxsw: pci: Reincrease PCI reset timeout
During driver initialization the driver sends a reset to the device and
waits for the firmware to signal that it is ready to continue.
Commit
d2f372ba0914 ("mlxsw: pci: Increase PCI SW reset timeout")
increased the timeout to 13 seconds due to longer PHY calibration in
Spectrum-2 compared to Spectrum-1.
Recently it became apparent that this timeout is too short and therefore
this patch increases it again to a safer limit that will be reduced in
the future.
Fixes: c3ab435466d5 ("mlxsw: spectrum: Extend to support Spectrum-2 ASIC")
Fixes: d2f372ba0914 ("mlxsw: pci: Increase PCI SW reset timeout")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Petr Machata [Thu, 18 Apr 2019 07:14:13 +0000 (07:14 +0000)]
mlxsw: spectrum: Put MC TCs into DWRR mode
Both Spectrum-1 and Spectrum-2 chips are currently configured such that
pairs of TC n (which is used for UC traffic) and TC n+8 (which is used
for MC traffic) are feeding into the same subgroup. Strict
prioritization is configured between the two TCs, and by enabling
MC-aware mode on the switch, the lower-numbered (UC) TCs are favored
over the higher-numbered (MC) TCs.
On Spectrum-2 however, there is an issue in configuration of the
MC-aware mode. As a result, MC traffic is prioritized over UC traffic.
To work around the issue, configure the MC TCs with DWRR mode (while
keeping the UC TCs in strict mode).
With this patch, the multicast-unicast arbitration results in the same
behavior on both Spectrum-1 and Spectrum-2 chips.
Fixes: 7b8195306694 ("mlxsw: spectrum: Configure MC-aware mode on mlxsw ports")
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Arnd Bergmann [Wed, 17 Apr 2019 16:29:13 +0000 (18:29 +0200)]
s390: ctcm: fix ctcm_new_device error return code
clang points out that the return code from this function is
undefined for one of the error paths:
../drivers/s390/net/ctcm_main.c:1595:7: warning: variable 'result' is used uninitialized whenever 'if' condition is true
[-Wsometimes-uninitialized]
if (priv->channel[direction] == NULL) {
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
../drivers/s390/net/ctcm_main.c:1638:9: note: uninitialized use occurs here
return result;
^~~~~~
../drivers/s390/net/ctcm_main.c:1595:3: note: remove the 'if' if its condition is always false
if (priv->channel[direction] == NULL) {
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
../drivers/s390/net/ctcm_main.c:1539:12: note: initialize the variable 'result' to silence this warning
int result;
^
Make it return -ENODEV here, as in the related failure cases.
gcc has a known bug in underreporting some of these warnings
when it has already eliminated the assignment of the return code
based on some earlier optimization step.
Reviewed-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Colin Ian King [Wed, 17 Apr 2019 13:15:00 +0000 (14:15 +0100)]
nfp: abm: fix spelling mistake "offseting" -> "offsetting"
There are a couple of spelling mistakes in NL_SET_ERR_MSG_MOD error
messages. Fix these.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Mukesh Ojha <mojha@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
YueHaibing [Wed, 17 Apr 2019 01:49:39 +0000 (09:49 +0800)]
net: stmmac: Use bfsize1 in ndesc_init_rx_desc
gcc warn this:
drivers/net/ethernet/stmicro/stmmac/norm_desc.c: In function ndesc_init_rx_desc:
drivers/net/ethernet/stmicro/stmmac/norm_desc.c:138:6: warning: variable 'bfsize1' set but not used [-Wunused-but-set-variable]
Like enh_desc_init_rx_desc, we should use bfsize1
in ndesc_init_rx_desc to calculate 'p->des1'
Fixes: 583e63614149 ("net: stmmac: use correct DMA buffer size in the RX descriptor")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Reviewed-by: Aaro Koskinen <aaro.koskinen@nokia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ZhangXiaoxu [Tue, 16 Apr 2019 01:47:24 +0000 (09:47 +0800)]
ipv4: set the tcp_min_rtt_wlen range from 0 to one day
There is a UBSAN report as below:
UBSAN: Undefined behaviour in net/ipv4/tcp_input.c:2877:56
signed integer overflow:
2147483647 * 1000 cannot be represented in type 'int'
CPU: 3 PID: 0 Comm: swapper/3 Not tainted
5.1.0-rc4-00058-g582549e #1
Call Trace:
<IRQ>
dump_stack+0x8c/0xba
ubsan_epilogue+0x11/0x60
handle_overflow+0x12d/0x170
? ttwu_do_wakeup+0x21/0x320
__ubsan_handle_mul_overflow+0x12/0x20
tcp_ack_update_rtt+0x76c/0x780
tcp_clean_rtx_queue+0x499/0x14d0
tcp_ack+0x69e/0x1240
? __wake_up_sync_key+0x2c/0x50
? update_group_capacity+0x50/0x680
tcp_rcv_established+0x4e2/0xe10
tcp_v4_do_rcv+0x22b/0x420
tcp_v4_rcv+0xfe8/0x1190
ip_protocol_deliver_rcu+0x36/0x180
ip_local_deliver+0x15b/0x1a0
ip_rcv+0xac/0xd0
__netif_receive_skb_one_core+0x7f/0xb0
__netif_receive_skb+0x33/0xc0
netif_receive_skb_internal+0x84/0x1c0
napi_gro_receive+0x2a0/0x300
receive_buf+0x3d4/0x2350
? detach_buf_split+0x159/0x390
virtnet_poll+0x198/0x840
? reweight_entity+0x243/0x4b0
net_rx_action+0x25c/0x770
__do_softirq+0x19b/0x66d
irq_exit+0x1eb/0x230
do_IRQ+0x7a/0x150
common_interrupt+0xf/0xf
</IRQ>
It can be reproduced by:
echo
2147483647 > /proc/sys/net/ipv4/tcp_min_rtt_wlen
Fixes: f672258391b42 ("tcp: track min RTT using windowed min-filter")
Signed-off-by: ZhangXiaoxu <zhangxiaoxu5@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Wed, 17 Apr 2019 17:25:25 +0000 (10:25 -0700)]
Merge tag 'for-linus-5.1-2' of git://github.com/cminyard/linux-ipmi
Pull IPMI fixes from Corey Minyard:
"Fixes for some bugs cause by recent changes. One crash if you feed bad
data to the module parameters, one BUG that sometimes occurs when a
user closes the connection, and one bug that cause the driver to not
work if the configuration information only comes in from SMBIOS"
* tag 'for-linus-5.1-2' of git://github.com/cminyard/linux-ipmi:
ipmi: fix sleep-in-atomic in free_user at cleanup SRCU user->release_barrier
ipmi: ipmi_si_hardcode.c: init si_type array to fix a crash
ipmi: Fix failure on SMBIOS specified devices
Linus Torvalds [Wed, 17 Apr 2019 16:57:45 +0000 (09:57 -0700)]
Merge git://git./linux/kernel/git/davem/net
Pull networking fixes from David Miller:
1) Handle init flow failures properly in iwlwifi driver, from Shahar S
Matityahu.
2) mac80211 TXQs need to be unscheduled on powersave start, from Felix
Fietkau.
3) SKB memory accounting fix in A-MDSU aggregation, from Felix Fietkau.
4) Increase RCU lock hold time in mlx5 FPGA code, from Saeed Mahameed.
5) Avoid checksum complete with XDP in mlx5, also from Saeed.
6) Fix netdev feature clobbering in ibmvnic driver, from Thomas Falcon.
7) Partial sent TLS record leak fix from Jakub Kicinski.
8) Reject zero size iova range in vhost, from Jason Wang.
9) Allow pending work to complete before clcsock release from Karsten
Graul.
10) Fix XDP handling max MTU in thunderx, from Matteo Croce.
11) A lot of protocols look at the sa_family field of a sockaddr before
validating it's length is large enough, from Tetsuo Handa.
12) Don't write to free'd pointer in qede ptp error path, from Colin Ian
King.
13) Have to recompile IP options in ipv4_link_failure because it can be
invoked from ARP, from Stephen Suryaputra.
14) Doorbell handling fixes in qed from Denis Bolotin.
15) Revert net-sysfs kobject register leak fix, it causes new problems.
From Wang Hai.
16) Spectre v1 fix in ATM code, from Gustavo A. R. Silva.
17) Fix put of BROPT_VLAN_STATS_PER_PORT in bridging code, from Nikolay
Aleksandrov.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (111 commits)
socket: fix compat SO_RCVTIMEO_NEW/SO_SNDTIMEO_NEW
tcp: tcp_grow_window() needs to respect tcp_space()
ocelot: Clean up stats update deferred work
ocelot: Don't sleep in atomic context (irqs_disabled())
net: bridge: fix netlink export of vlan_stats_per_port option
qed: fix spelling mistake "faspath" -> "fastpath"
tipc: set sysctl_tipc_rmem and named_timeout right range
tipc: fix link established but not in session
net: Fix missing meta data in skb with vlan packet
net: atm: Fix potential Spectre v1 vulnerabilities
net/core: work around section mismatch warning for ptp_classifier
net: bridge: fix per-port af_packet sockets
bnx2x: fix spelling mistake "dicline" -> "decline"
route: Avoid crash from dereferencing NULL rt->from
MAINTAINERS: normalize Woojung Huh's email address
bonding: fix event handling for stacked bonds
Revert "net-sysfs: Fix memory leak in netdev_register_kobject"
rtnetlink: fix rtnl_valid_stats_req() nlmsg_len check
qed: Fix the DORQ's attentions handling
qed: Fix missing DORQ attentions
...
Corey Minyard [Wed, 3 Apr 2019 20:58:16 +0000 (15:58 -0500)]
ipmi: fix sleep-in-atomic in free_user at cleanup SRCU user->release_barrier
free_user() could be called in atomic context.
This patch pushed the free operation off into a workqueue.
Example:
BUG: sleeping function called from invalid context at kernel/workqueue.c:2856
in_atomic(): 1, irqs_disabled(): 0, pid: 177, name: ksoftirqd/27
CPU: 27 PID: 177 Comm: ksoftirqd/27 Not tainted 4.19.25-3 #1
Hardware name: AIC 1S-HV26-08/MB-DPSB04-06, BIOS IVYBV060 10/21/2015
Call Trace:
dump_stack+0x5c/0x7b
___might_sleep+0xec/0x110
__flush_work+0x48/0x1f0
? try_to_del_timer_sync+0x4d/0x80
_cleanup_srcu_struct+0x104/0x140
free_user+0x18/0x30 [ipmi_msghandler]
ipmi_free_recv_msg+0x3a/0x50 [ipmi_msghandler]
deliver_response+0xbd/0xd0 [ipmi_msghandler]
deliver_local_response+0xe/0x30 [ipmi_msghandler]
handle_one_recv_msg+0x163/0xc80 [ipmi_msghandler]
? dequeue_entity+0xa0/0x960
handle_new_recv_msgs+0x15c/0x1f0 [ipmi_msghandler]
tasklet_action_common.isra.22+0x103/0x120
__do_softirq+0xf8/0x2d7
run_ksoftirqd+0x26/0x50
smpboot_thread_fn+0x11d/0x1e0
kthread+0x103/0x140
? sort_range+0x20/0x20
? kthread_destroy_worker+0x40/0x40
ret_from_fork+0x1f/0x40
Fixes: 77f8269606bf ("ipmi: fix use-after-free of user->release_barrier.rda")
Reported-by: Konstantin Khlebnikov <khlebnikov@yandex-team.ru>
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Cc: stable@vger.kernel.org # 5.0
Cc: Yang Yingliang <yangyingliang@huawei.com>
Arnd Bergmann [Tue, 16 Apr 2019 20:31:14 +0000 (22:31 +0200)]
socket: fix compat SO_RCVTIMEO_NEW/SO_SNDTIMEO_NEW
It looks like the new socket options only work correctly
for native execution, but in case of compat mode fall back
to the old behavior as we ignore the 'old_timeval' flag.
Rework so we treat SO_RCVTIMEO_NEW/SO_SNDTIMEO_NEW the
same way in compat and native 32-bit mode.
Cc: Deepa Dinamani <deepa.kernel@gmail.com>
Fixes: a9beb86ae6e5 ("sock: Add SO_RCVTIMEO_NEW and SO_SNDTIMEO_NEW")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Deepa Dinamani <deepa.kernel@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Tue, 16 Apr 2019 17:55:20 +0000 (10:55 -0700)]
tcp: tcp_grow_window() needs to respect tcp_space()
For some reason, tcp_grow_window() correctly tests if enough room
is present before attempting to increase tp->rcv_ssthresh,
but does not prevent it to grow past tcp_space()
This is causing hard to debug issues, like failing
the (__tcp_select_window(sk) >= tp->rcv_wnd) test
in __tcp_ack_snd_check(), causing ACK delays and possibly
slow flows.
Depending on tcp_rmem[2], MTU, skb->len/skb->truesize ratio,
we can see the problem happening on "netperf -t TCP_RR -- -r 2000,2000"
after about 60 round trips, when the active side no longer sends
immediate acks.
This bug predates git history.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Soheil Hassas Yeganeh <soheil@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Acked-by: Wei Wang <weiwan@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Claudiu Manoil [Tue, 16 Apr 2019 14:51:59 +0000 (17:51 +0300)]
ocelot: Clean up stats update deferred work
This is preventive cleanup that may save troubles later.
No need to cancel repeateadly queued work if code is properly
refactored.
Don't let the ethtool -s process interfere with the stat workqueue
scheduling.
Signed-off-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Claudiu Manoil [Tue, 16 Apr 2019 14:51:58 +0000 (17:51 +0300)]
ocelot: Don't sleep in atomic context (irqs_disabled())
Preemption disabled at:
[<
ffff000008cabd54>] dev_set_rx_mode+0x1c/0x38
Call trace:
[<
ffff00000808a5c0>] dump_backtrace+0x0/0x3d0
[<
ffff00000808a9a4>] show_stack+0x14/0x20
[<
ffff000008e6c0c0>] dump_stack+0xac/0xe4
[<
ffff0000080fe76c>] ___might_sleep+0x164/0x238
[<
ffff0000080fe890>] __might_sleep+0x50/0x88
[<
ffff0000082261e4>] kmem_cache_alloc+0x17c/0x1d0
[<
ffff000000ea0ae8>] ocelot_set_rx_mode+0x108/0x188 [mscc_ocelot_common]
[<
ffff000008cabcf0>] __dev_set_rx_mode+0x58/0xa0
[<
ffff000008cabd5c>] dev_set_rx_mode+0x24/0x38
Fixes: a556c76adc05 ("net: mscc: Add initial Ocelot switch support")
Signed-off-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Nikolay Aleksandrov [Tue, 16 Apr 2019 13:15:56 +0000 (16:15 +0300)]
net: bridge: fix netlink export of vlan_stats_per_port option
Since the introduction of the vlan_stats_per_port option the netlink
export of it has been broken since I made a typo and used the ifla
attribute instead of the bridge option to retrieve its state.
Sysfs export is fine, only netlink export has been affected.
Fixes: 9163a0fc1f0c0 ("net: bridge: add support for per-port vlan stats")
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Colin Ian King [Tue, 16 Apr 2019 11:43:17 +0000 (12:43 +0100)]
qed: fix spelling mistake "faspath" -> "fastpath"
There is a spelling mistake in a DP_INFO message, fix it.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Mukesh Ojha <mojha@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jie Liu [Tue, 16 Apr 2019 05:10:09 +0000 (13:10 +0800)]
tipc: set sysctl_tipc_rmem and named_timeout right range
We find that sysctl_tipc_rmem and named_timeout do not have the right minimum
setting. sysctl_tipc_rmem should be larger than zero, like sysctl_tcp_rmem.
And named_timeout as a timeout setting should be not less than zero.
Fixes: cc79dd1ba9c10 ("tipc: change socket buffer overflow control to respect sk_rcvbuf")
Fixes: a5325ae5b8bff ("tipc: add name distributor resiliency queue")
Signed-off-by: Jie Liu <liujie165@huawei.com>
Reported-by: Qiang Ning <ningqiang1@huawei.com>
Reviewed-by: Zhiqiang Liu <liuzhiqiang26@huawei.com>
Reviewed-by: Miaohe Lin <linmiaohe@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Tuong Lien [Tue, 16 Apr 2019 03:48:07 +0000 (10:48 +0700)]
tipc: fix link established but not in session
According to the link FSM, when a link endpoint got RESET_MSG (- a
traditional one without the stopping bit) from its peer, it moves to
PEER_RESET state and raises a LINK_DOWN event which then resets the
link itself. Its state will become ESTABLISHING after the reset event
and the link will be re-established soon after this endpoint starts to
send ACTIVATE_MSG to the peer.
There is no problem with this mechanism, however the link resetting has
cleared the link 'in_session' flag (along with the other important link
data such as: the link 'mtu') that was correctly set up at the 1st step
(i.e. when this endpoint received the peer RESET_MSG). As a result, the
link will become ESTABLISHED, but the 'in_session' flag is not set, and
all STATE_MSG from its peer will be dropped at the link_validate_msg().
It means the link not synced and will sooner or later face a failure.
Since the link reset action is obviously needed for a new link session
(this is also true in the other situations), the problem here is that
the link is re-established a bit too early when the link endpoints are
not really in-sync yet. The commit forces a resync as already done in
the previous commit
91986ee166cf ("tipc: fix link session and
re-establish issues") by simply varying the link 'peer_session' value
at the link_reset().
Acked-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: Tuong Lien <tuong.t.lien@dektech.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Yuya Kusakabe [Tue, 16 Apr 2019 01:22:28 +0000 (10:22 +0900)]
net: Fix missing meta data in skb with vlan packet
skb_reorder_vlan_header() should move XDP meta data with ethernet header
if XDP meta data exists.
Fixes: de8f3a83b0a0 ("bpf: add meta pointer for direct access")
Signed-off-by: Yuya Kusakabe <yuya.kusakabe@gmail.com>
Signed-off-by: Takeru Hayasaka <taketarou2@gmail.com>
Co-developed-by: Takeru Hayasaka <taketarou2@gmail.com>
Reviewed-by: Toshiaki Makita <makita.toshiaki@lab.ntt.co.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>
Gustavo A. R. Silva [Mon, 15 Apr 2019 20:57:23 +0000 (15:57 -0500)]
net: atm: Fix potential Spectre v1 vulnerabilities
arg is controlled by user-space, hence leading to a potential
exploitation of the Spectre variant 1 vulnerability.
This issue was detected with the help of Smatch:
net/atm/lec.c:715 lec_mcast_attach() warn: potential spectre issue 'dev_lec' [r] (local cap)
Fix this by sanitizing arg before using it to index dev_lec.
Notice that given that speculation windows are large, the policy is
to kill the speculation on the first load and not worry if it can be
completed with a dependent load/store [1].
[1] https://lore.kernel.org/lkml/
20180423164740.GY17484@dhcp22.suse.cz/
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ard Biesheuvel [Mon, 15 Apr 2019 17:14:45 +0000 (19:14 +0200)]
net/core: work around section mismatch warning for ptp_classifier
The routine ptp_classifier_init() uses an initializer for an
automatic struct type variable which refers to an __initdata
symbol. This is perfectly legal, but may trigger a section
mismatch warning when running the compiler in -fpic mode, due
to the fact that the initializer may be emitted into an anonymous
.data section thats lack the __init annotation. So work around it
by using assignments instead.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Gerald Schaefer <gerald.schaefer@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Nikolay Aleksandrov [Thu, 11 Apr 2019 10:56:39 +0000 (13:56 +0300)]
net: bridge: fix per-port af_packet sockets
When the commit below was introduced it changed two visible things:
- the skb was no longer passed through the protocol handlers with the
original device
- the skb was passed up the stack with skb->dev = bridge
The first change broke af_packet sockets on bridge ports. For example we
use them for hostapd which listens for ETH_P_PAE packets on the ports.
We discussed two possible fixes:
- create a clone and pass it through NF_HOOK(), act on the original skb
based on the result
- somehow signal to the caller from the okfn() that it was called,
meaning the skb is ok to be passed, which this patch is trying to
implement via returning 1 from the bridge link-local okfn()
Note that we rely on the fact that NF_QUEUE/STOLEN would return 0 and
drop/error would return < 0 thus the okfn() is called only when the
return was 1, so we signal to the caller that it was called by preserving
the return value from nf_hook().
Fixes: 8626c56c8279 ("bridge: fix potential use-after-free when hook returns QUEUE or STOLEN verdict")
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Tony Camuso [Tue, 9 Apr 2019 19:20:03 +0000 (15:20 -0400)]
ipmi: ipmi_si_hardcode.c: init si_type array to fix a crash
The intended behavior of function ipmi_hardcode_init_one() is to default
to kcs interface when no type argument is presented when initializing
ipmi with hard coded addresses.
However, the array of char pointers allocated on the stack by function
ipmi_hardcode_init() was not inited to zeroes, so it contained stack
debris.
Consequently, passing the cruft stored in this array to function
ipmi_hardcode_init_one() caused a crash when it was unable to detect
that the char * being passed was nonsense and tried to access the
address specified by the bogus pointer.
The fix is simply to initialize the si_type array to zeroes, so if
there were no type argument given to at the command line, function
ipmi_hardcode_init_one() could properly default to the kcs interface.
Signed-off-by: Tony Camuso <tcamuso@redhat.com>
Message-Id: <
1554837603-40299-1-git-send-email-tcamuso@redhat.com>
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Corey Minyard [Tue, 16 Apr 2019 21:26:45 +0000 (16:26 -0500)]
ipmi: Fix failure on SMBIOS specified devices
An extra memset was put into a place that cleared the interface
type.
Reported-by: Tony Camuso <tcamuso@redhat.com>
Fixes: 3cd83bac481dc4 ("ipmi: Consolidate the adding of platform devices")
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Linus Torvalds [Tue, 16 Apr 2019 17:46:37 +0000 (10:46 -0700)]
Merge tag 'riscv-for-linus-5.1-rc6' of git://git./linux/kernel/git/palmer/riscv-linux
Pull RISC-V fixes from Palmer Dabbelt:
"This contains an assortment of RISC-V-related fixups that we found
after rc4. They're all really unrelated:
- The addition of a 32-bit defconfig, to emphasize testing the 32-bit
port.
- A device tree bindings patch, which is pre-work for some patches
that target 5.2.
- A fix to support booting on systems with more physical memory than
the maximum supported by the kernel"
* tag 'riscv-for-linus-5.1-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/palmer/riscv-linux:
RISC-V: Fix Maximum Physical Memory 2GiB option for 64bit systems
dt-bindings: clock: sifive: add FU540-C000 PRCI clock constants
RISC-V: Add separate defconfig for 32bit systems
Linus Torvalds [Tue, 16 Apr 2019 15:52:00 +0000 (08:52 -0700)]
Merge tag 'for-linus' of git://git./virt/kvm/kvm
Pull KVM fixes from Paolo Bonzini:
"5.1 keeps its reputation as a big bugfix release for KVM x86.
- Fix for a memory leak introduced during the merge window
- Fixes for nested VMX with ept=0
- Fixes for AMD (APIC virtualization, NMI injection)
- Fixes for Hyper-V under KVM and KVM under Hyper-V
- Fixes for 32-bit SMM and tests for SMM virtualization
- More array_index_nospec peppering"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (21 commits)
KVM: x86: avoid misreporting level-triggered irqs as edge-triggered in tracing
KVM: fix spectrev1 gadgets
KVM: x86: fix warning Using plain integer as NULL pointer
selftests: kvm: add a selftest for SMM
selftests: kvm: fix for compilers that do not support -no-pie
selftests: kvm/evmcs_test: complete I/O before migrating guest state
KVM: x86: Always use 32-bit SMRAM save state for 32-bit kernels
KVM: x86: Don't clear EFER during SMM transitions for 32-bit vCPU
KVM: x86: clear SMM flags before loading state while leaving SMM
KVM: x86: Open code kvm_set_hflags
KVM: x86: Load SMRAM in a single shot when leaving SMM
KVM: nVMX: Expose RDPMC-exiting only when guest supports PMU
KVM: x86: Raise #GP when guest vCPU do not support PMU
x86/kvm: move kvm_load/put_guest_xcr0 into atomic context
KVM: x86: svm: make sure NMI is injected after nmi_singlestep
svm/avic: Fix invalidate logical APIC id entry
Revert "svm: Fix AVIC incomplete IPI emulation"
kvm: mmu: Fix overflow on kvm mmu page limit calculation
KVM: nVMX: always use early vmcs check when EPT is disabled
KVM: nVMX: allow tests to use bad virtual-APIC page address
...
Vitaly Kuznetsov [Wed, 27 Mar 2019 14:12:20 +0000 (15:12 +0100)]
KVM: x86: avoid misreporting level-triggered irqs as edge-triggered in tracing
In __apic_accept_irq() interface trig_mode is int and actually on some code
paths it is set above u8:
kvm_apic_set_irq() extracts it from 'struct kvm_lapic_irq' where trig_mode
is u16. This is done on purpose as e.g. kvm_set_msi_irq() sets it to
(1 << 15) & e->msi.data
kvm_apic_local_deliver sets it to reg & (1 << 15).
Fix the immediate issue by making 'tm' into u16. We may also want to adjust
__apic_accept_irq() interface and use proper sizes for vector, level,
trig_mode but this is not urgent.
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Paolo Bonzini [Thu, 11 Apr 2019 09:16:47 +0000 (11:16 +0200)]
KVM: fix spectrev1 gadgets
These were found with smatch, and then generalized when applicable.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Hariprasad Kelam [Sat, 6 Apr 2019 09:36:58 +0000 (15:06 +0530)]
KVM: x86: fix warning Using plain integer as NULL pointer
Changed passing argument as "0 to NULL" which resolves below sparse warning
arch/x86/kvm/x86.c:3096:61: warning: Using plain integer as NULL pointer
Signed-off-by: Hariprasad Kelam <hariprasad.kelam@gmail.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Vitaly Kuznetsov [Wed, 10 Apr 2019 09:38:33 +0000 (11:38 +0200)]
selftests: kvm: add a selftest for SMM
Add a simple test for SMM, based on VMX. The test implements its own
sync between the guest and the host as using our ucall library seems to
be too cumbersome: SMI handler is happening in real-address mode.
This patch also fixes KVM_SET_NESTED_STATE to happen after
KVM_SET_VCPU_EVENTS, in fact it places it last. This is because
KVM needs to know whether the processor is in SMM or not.
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Paolo Bonzini [Thu, 11 Apr 2019 13:51:19 +0000 (15:51 +0200)]
selftests: kvm: fix for compilers that do not support -no-pie
-no-pie was added to GCC at the same time as their configuration option
--enable-default-pie. Compilers that were built before do not have
-no-pie, but they also do not need it. Detect the option at build
time.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Paolo Bonzini [Thu, 11 Apr 2019 13:57:14 +0000 (15:57 +0200)]
selftests: kvm/evmcs_test: complete I/O before migrating guest state
Starting state migration after an IO exit without first completing IO
may result in test failures. We already have two tests that need this
(this patch in fact fixes evmcs_test, similar to what was fixed for
state_test in commit
0f73bbc851ed, "KVM: selftests: complete IO before
migrating guest state", 2019-03-13) and a third is coming. So, move the
code to vcpu_save_state, and while at it do not access register state
until after I/O is complete.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Sean Christopherson [Tue, 2 Apr 2019 15:10:48 +0000 (08:10 -0700)]
KVM: x86: Always use 32-bit SMRAM save state for 32-bit kernels
Invoking the 64-bit variation on a 32-bit kenrel will crash the guest,
trigger a WARN, and/or lead to a buffer overrun in the host, e.g.
rsm_load_state_64() writes r8-r15 unconditionally, but enum kvm_reg and
thus x86_emulate_ctxt._regs only define r8-r15 for CONFIG_X86_64.
KVM allows userspace to report long mode support via CPUID, even though
the guest is all but guaranteed to crash if it actually tries to enable
long mode. But, a pure 32-bit guest that is ignorant of long mode will
happily plod along.
SMM complicates things as 64-bit CPUs use a different SMRAM save state
area. KVM handles this correctly for 64-bit kernels, e.g. uses the
legacy save state map if userspace has hid long mode from the guest,
but doesn't fare well when userspace reports long mode support on a
32-bit host kernel (32-bit KVM doesn't support 64-bit guests).
Since the alternative is to crash the guest, e.g. by not loading state
or explicitly requesting shutdown, unconditionally use the legacy SMRAM
save state map for 32-bit KVM. If a guest has managed to get far enough
to handle SMIs when running under a weird/buggy userspace hypervisor,
then don't deliberately crash the guest since there are no downsides
(from KVM's perspective) to allow it to continue running.
Fixes: 660a5d517aaab ("KVM: x86: save/load state on SMM switch")
Cc: stable@vger.kernel.org
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Sean Christopherson [Tue, 2 Apr 2019 15:10:47 +0000 (08:10 -0700)]
KVM: x86: Don't clear EFER during SMM transitions for 32-bit vCPU
Neither AMD nor Intel CPUs have an EFER field in the legacy SMRAM save
state area, i.e. don't save/restore EFER across SMM transitions. KVM
somewhat models this, e.g. doesn't clear EFER on entry to SMM if the
guest doesn't support long mode. But during RSM, KVM unconditionally
clears EFER so that it can get back to pure 32-bit mode in order to
start loading CRs with their actual non-SMM values.
Clear EFER only when it will be written when loading the non-SMM state
so as to preserve bits that can theoretically be set on 32-bit vCPUs,
e.g. KVM always emulates EFER_SCE.
And because CR4.PAE is cleared only to play nice with EFER, wrap that
code in the long mode check as well. Note, this may result in a
compiler warning about cr4 being consumed uninitialized. Re-read CR4
even though it's technically unnecessary, as doing so allows for more
readable code and RSM emulation is not a performance critical path.
Fixes: 660a5d517aaab ("KVM: x86: save/load state on SMM switch")
Cc: stable@vger.kernel.org
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Sean Christopherson [Tue, 2 Apr 2019 15:03:11 +0000 (08:03 -0700)]
KVM: x86: clear SMM flags before loading state while leaving SMM
RSM emulation is currently broken on VMX when the interrupted guest has
CR4.VMXE=1. Stop dancing around the issue of HF_SMM_MASK being set when
loading SMSTATE into architectural state, e.g. by toggling it for
problematic flows, and simply clear HF_SMM_MASK prior to loading
architectural state (from SMRAM save state area).
Reported-by: Jon Doron <arilou@gmail.com>
Cc: Jim Mattson <jmattson@google.com>
Cc: Liran Alon <liran.alon@oracle.com>
Cc: Vitaly Kuznetsov <vkuznets@redhat.com>
Fixes: 5bea5123cbf0 ("KVM: VMX: check nested state and CR4.VMXE against SMM")
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Tested-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Sean Christopherson [Tue, 2 Apr 2019 15:03:10 +0000 (08:03 -0700)]
KVM: x86: Open code kvm_set_hflags
Prepare for clearing HF_SMM_MASK prior to loading state from the SMRAM
save state map, i.e. kvm_smm_changed() needs to be called after state
has been loaded and so cannot be done automatically when setting
hflags from RSM.
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Sean Christopherson [Tue, 2 Apr 2019 15:03:09 +0000 (08:03 -0700)]
KVM: x86: Load SMRAM in a single shot when leaving SMM
RSM emulation is currently broken on VMX when the interrupted guest has
CR4.VMXE=1. Rather than dance around the issue of HF_SMM_MASK being set
when loading SMSTATE into architectural state, ideally RSM emulation
itself would be reworked to clear HF_SMM_MASK prior to loading non-SMM
architectural state.
Ostensibly, the only motivation for having HF_SMM_MASK set throughout
the loading of state from the SMRAM save state area is so that the
memory accesses from GET_SMSTATE() are tagged with role.smm. Load
all of the SMRAM save state area from guest memory at the beginning of
RSM emulation, and load state from the buffer instead of reading guest
memory one-by-one.
This paves the way for clearing HF_SMM_MASK prior to loading state,
and also aligns RSM with the enter_smm() behavior, which fills a
buffer and writes SMRAM save state in a single go.
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Liran Alon [Mon, 25 Mar 2019 19:09:17 +0000 (21:09 +0200)]
KVM: nVMX: Expose RDPMC-exiting only when guest supports PMU
Issue was discovered when running kvm-unit-tests on KVM running as L1 on
top of Hyper-V.
When vmx_instruction_intercept unit-test attempts to run RDPMC to test
RDPMC-exiting, it is intercepted by L1 KVM which it's EXIT_REASON_RDPMC
handler raise #GP because vCPU exposed by Hyper-V doesn't support PMU.
Instead of unit-test expectation to be reflected with EXIT_REASON_RDPMC.
The reason vmx_instruction_intercept unit-test attempts to run RDPMC
even though Hyper-V doesn't support PMU is because L1 expose to L2
support for RDPMC-exiting. Which is reasonable to assume that is
supported only in case CPU supports PMU to being with.
Above issue can easily be simulated by modifying
vmx_instruction_intercept config in x86/unittests.cfg to run QEMU with
"-cpu host,+vmx,-pmu" and run unit-test.
To handle issue, change KVM to expose RDPMC-exiting only when guest
supports PMU.
Reported-by: Saar Amar <saaramar@microsoft.com>
Reviewed-by: Mihai Carabas <mihai.carabas@oracle.com>
Reviewed-by: Jim Mattson <jmattson@google.com>
Signed-off-by: Liran Alon <liran.alon@oracle.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Liran Alon [Mon, 25 Mar 2019 19:10:17 +0000 (21:10 +0200)]
KVM: x86: Raise #GP when guest vCPU do not support PMU
Before this change, reading a VMware pseduo PMC will succeed even when
PMU is not supported by guest. This can easily be seen by running
kvm-unit-test vmware_backdoors with "-cpu host,-pmu" option.
Reviewed-by: Mihai Carabas <mihai.carabas@oracle.com>
Signed-off-by: Liran Alon <liran.alon@oracle.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
WANG Chao [Fri, 12 Apr 2019 07:55:39 +0000 (15:55 +0800)]
x86/kvm: move kvm_load/put_guest_xcr0 into atomic context
guest xcr0 could leak into host when MCE happens in guest mode. Because
do_machine_check() could schedule out at a few places.
For example:
kvm_load_guest_xcr0
...
kvm_x86_ops->run(vcpu) {
vmx_vcpu_run
vmx_complete_atomic_exit
kvm_machine_check
do_machine_check
do_memory_failure
memory_failure
lock_page
In this case, host_xcr0 is 0x2ff, guest vcpu xcr0 is 0xff. After schedule
out, host cpu has guest xcr0 loaded (0xff).
In __switch_to {
switch_fpu_finish
copy_kernel_to_fpregs
XRSTORS
If any bit i in XSTATE_BV[i] == 1 and xcr0[i] == 0, XRSTORS will
generate #GP (In this case, bit 9). Then ex_handler_fprestore kicks in
and tries to reinitialize fpu by restoring init fpu state. Same story as
last #GP, except we get DOUBLE FAULT this time.
Cc: stable@vger.kernel.org
Signed-off-by: WANG Chao <chao.wang@ucloud.cn>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Vitaly Kuznetsov [Wed, 3 Apr 2019 14:06:42 +0000 (16:06 +0200)]
KVM: x86: svm: make sure NMI is injected after nmi_singlestep
I noticed that apic test from kvm-unit-tests always hangs on my EPYC 7401P,
the hanging test nmi-after-sti is trying to deliver 30000 NMIs and tracing
shows that we're sometimes able to deliver a few but never all.
When we're trying to inject an NMI we may fail to do so immediately for
various reasons, however, we still need to inject it so enable_nmi_window()
arms nmi_singlestep mode. #DB occurs as expected, but we're not checking
for pending NMIs before entering the guest and unless there's a different
event to process, the NMI will never get delivered.
Make KVM_REQ_EVENT request on the vCPU from db_interception() to make sure
pending NMIs are checked and possibly injected.
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Cc: stable@vger.kernel.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Suthikulpanit, Suravee [Tue, 26 Mar 2019 03:57:37 +0000 (03:57 +0000)]
svm/avic: Fix invalidate logical APIC id entry
Only clear the valid bit when invalidate logical APIC id entry.
The current logic clear the valid bit, but also set the rest of
the bits (including reserved bits) to 1.
Fixes: 98d90582be2e ('svm: Fix AVIC DFR and LDR handling')
Signed-off-by: Suravee Suthikulpanit <suravee.suthikulpanit@amd.com>
Cc: stable@vger.kernel.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Suthikulpanit, Suravee [Wed, 20 Mar 2019 08:12:28 +0000 (08:12 +0000)]
Revert "svm: Fix AVIC incomplete IPI emulation"
This reverts commit
bb218fbcfaaa3b115d4cd7a43c0ca164f3a96e57.
As Oren Twaig pointed out the old discussion:
https://patchwork.kernel.org/patch/
8292231/
that the change coud potentially cause an extra IPI to be sent to
the destination vcpu because the AVIC hardware already set the IRR bit
before the incomplete IPI #VMEXIT with id=1 (target vcpu is not running).
Since writting to ICR and ICR2 will also set the IRR. If something triggers
the destination vcpu to get scheduled before the emulation finishes, then
this could result in an additional IPI.
Also, the issue mentioned in the commit
bb218fbcfaaa was misdiagnosed.
Cc: Radim Krčmář <rkrcmar@redhat.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Reported-by: Oren Twaig <oren@scalemp.com>
Signed-off-by: Suravee Suthikulpanit <suravee.suthikulpanit@amd.com>
Cc: stable@vger.kernel.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Ben Gardon [Mon, 8 Apr 2019 18:07:30 +0000 (11:07 -0700)]
kvm: mmu: Fix overflow on kvm mmu page limit calculation
KVM bases its memory usage limits on the total number of guest pages
across all memslots. However, those limits, and the calculations to
produce them, use 32 bit unsigned integers. This can result in overflow
if a VM has more guest pages that can be represented by a u32. As a
result of this overflow, KVM can use a low limit on the number of MMU
pages it will allocate. This makes KVM unable to map all of guest memory
at once, prompting spurious faults.
Tested: Ran all kvm-unit-tests on an Intel Haswell machine. This patch
introduced no new failures.
Signed-off-by: Ben Gardon <bgardon@google.com>
Cc: stable@vger.kernel.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Paolo Bonzini [Mon, 15 Apr 2019 13:57:19 +0000 (15:57 +0200)]
KVM: nVMX: always use early vmcs check when EPT is disabled
The remaining failures of vmx.flat when EPT is disabled are caused by
incorrectly reflecting VMfails to the L1 hypervisor. What happens is
that nested_vmx_restore_host_state corrupts the guest CR3, reloading it
with the host's shadow CR3 instead, because it blindly loads GUEST_CR3
from the vmcs01.
For simplicity let's just always use hardware VMCS checks when EPT is
disabled. This way, nested_vmx_restore_host_state is not reached at
all (or at least shouldn't be reached).
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Paolo Bonzini [Mon, 15 Apr 2019 13:16:17 +0000 (15:16 +0200)]
KVM: nVMX: allow tests to use bad virtual-APIC page address
As mentioned in the comment, there are some special cases where we can simply
clear the TPR shadow bit from the CPU-based execution controls in the vmcs02.
Handle them so that we can remove some XFAILs from vmx.flat.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Colin Ian King [Mon, 15 Apr 2019 15:47:03 +0000 (16:47 +0100)]
bnx2x: fix spelling mistake "dicline" -> "decline"
There is a spelling mistake in a BNX2X_ERR message, fix it.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Mon, 15 Apr 2019 23:48:51 +0000 (16:48 -0700)]
Merge tag 'libnvdimm-fixes-5.1-rc6' of git://git./linux/kernel/git/nvdimm/nvdimm
Pull libnvdimm fixes from Dan Williams:
"I debated holding this back for the v5.2 merge window due to the size
of the "zero-key" changes, but affected users would benefit from
having the fixes sooner. It did not make sense to change the zero-key
semantic in isolation for the "secure-erase" command, but instead
include it for all security commands.
The short background on the need for these changes is that some NVDIMM
platforms enable security with a default zero-key rather than let the
OS specify the initial key. This makes the security enabling that
landed in v5.0 unusable for some users.
Summary:
- Compatibility fix for nvdimm-security implementations with a
default zero-key.
- Miscellaneous small fixes for out-of-bound accesses, cleanup after
initialization failures, and missing debug messages"
* tag 'libnvdimm-fixes-5.1-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm:
tools/testing/nvdimm: Retain security state after overwrite
libnvdimm/pmem: fix a possible OOB access when read and write pmem
libnvdimm/security, acpi/nfit: unify zero-key for all security commands
libnvdimm/security: provide fix for secure-erase to use zero-key
libnvdimm/btt: Fix a kmemdup failure check
libnvdimm/namespace: Fix a potential NULL pointer dereference
acpi/nfit: Always dump _DSM output payload
Linus Torvalds [Mon, 15 Apr 2019 22:10:20 +0000 (15:10 -0700)]
Merge tag 'fsdax-fix-5.1-rc6' of git://git./linux/kernel/git/nvdimm/nvdimm
Pull fsdax fix from Dan Williams:
"A single filesystem-dax fix. It has been lingering in -next for a long
while and there are no other fsdax fixes on the horizon:
- Avoid a crash scenario with architectures like powerpc that require
'pgtable_deposit' for the zero page"
* tag 'fsdax-fix-5.1-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm:
fs/dax: Deposit pagetable even when installing zero page
Jonathan Lemon [Sun, 14 Apr 2019 21:21:29 +0000 (14:21 -0700)]
route: Avoid crash from dereferencing NULL rt->from
When __ip6_rt_update_pmtu() is called, rt->from is RCU dereferenced, but is
never checked for null - rt6_flush_exceptions() may have removed the entry.
[ 1913.989004] RIP: 0010:ip6_rt_cache_alloc+0x13/0x170
[ 1914.209410] Call Trace:
[ 1914.214798] <IRQ>
[ 1914.219226] __ip6_rt_update_pmtu+0xb0/0x190
[ 1914.228649] ip6_tnl_xmit+0x2c2/0x970 [ip6_tunnel]
[ 1914.239223] ? ip6_tnl_parse_tlv_enc_lim+0x32/0x1a0 [ip6_tunnel]
[ 1914.252489] ? __gre6_xmit+0x148/0x530 [ip6_gre]
[ 1914.262678] ip6gre_tunnel_xmit+0x17e/0x3c7 [ip6_gre]
[ 1914.273831] dev_hard_start_xmit+0x8d/0x1f0
[ 1914.283061] sch_direct_xmit+0xfa/0x230
[ 1914.291521] __qdisc_run+0x154/0x4b0
[ 1914.299407] net_tx_action+0x10e/0x1f0
[ 1914.307678] __do_softirq+0xca/0x297
[ 1914.315567] irq_exit+0x96/0xa0
[ 1914.322494] smp_apic_timer_interrupt+0x68/0x130
[ 1914.332683] apic_timer_interrupt+0xf/0x20
[ 1914.341721] </IRQ>
Fixes: a68886a69180 ("net/ipv6: Make from in rt6_info rcu protected")
Signed-off-by: Jonathan Lemon <jonathan.lemon@gmail.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Reviewed-by: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Lukas Bulwahn [Sat, 13 Apr 2019 07:52:15 +0000 (09:52 +0200)]
MAINTAINERS: normalize Woojung Huh's email address
MAINTAINERS contains a lower-case and upper-case variant of
Woojung Huh' s email address.
Only keep the lower-case variant in MAINTAINERS.
Signed-off-by: Lukas Bulwahn <lukas.bulwahn@gmail.com>
Acked-by: Woojung Huh <woojung.huh@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Sabrina Dubroca [Fri, 12 Apr 2019 13:04:10 +0000 (15:04 +0200)]
bonding: fix event handling for stacked bonds
When a bond is enslaved to another bond, bond_netdev_event() only
handles the event as if the bond is a master, and skips treating the
bond as a slave.
This leads to a refcount leak on the slave, since we don't remove the
adjacency to its master and the master holds a reference on the slave.
Reproducer:
ip link add bondL type bond
ip link add bondU type bond
ip link set bondL master bondU
ip link del bondL
No "Fixes:" tag, this code is older than git history.
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Wang Hai [Fri, 12 Apr 2019 20:36:33 +0000 (16:36 -0400)]
Revert "net-sysfs: Fix memory leak in netdev_register_kobject"
This reverts commit
6b70fc94afd165342876e53fc4b2f7d085009945.
The reverted bugfix will cause another issue.
Reported by syzbot+
6024817a931b2830bc93@syzkaller.appspotmail.com.
See https://syzkaller.appspot.com/x/log.txt?x=
1737671b200000 for
details.
Signed-off-by: Wang Hai <wanghai26@huawei.com>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Mon, 15 Apr 2019 19:02:29 +0000 (12:02 -0700)]
Merge tag 'wireless-drivers-for-davem-2019-04-15' of git://git./linux/kernel/git/kvalo/wireless-drivers
Kalle Valo says:
====================
wireless-drivers fixes for 5.1
Second set of fixes for 5.1.
iwlwifi
* add some new PCI IDs (plus a struct name change they depend on)
* fix crypto with new devices, namely 22560 and above
* fix for a potential deadlock in the TX path
* a fix for offloaded rate-control
* support new PCI HW IDs which use a new FW
mt76
* fix lock initialisation and a possible deadlock
* aggregation fixes
rt2x00
* fix sequence numbering during retransmits
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Sean Christopherson [Sat, 13 Apr 2019 02:55:41 +0000 (19:55 -0700)]
KVM: x86/mmu: Fix an inverted list_empty() check when zapping sptes
A recently introduced helper for handling zap vs. remote flush
incorrectly bails early, effectively leaking defunct shadow pages.
Manifests as a slab BUG when exiting KVM due to the shadow pages
being alive when their associated cache is destroyed.
==========================================================================
BUG kvm_mmu_page_header: Objects remaining in kvm_mmu_page_header on ...
--------------------------------------------------------------------------
Disabling lock debugging due to kernel taint
INFO: Slab 0x00000000fc436387 objects=26 used=23 fp=0x00000000d023caee ...
CPU: 6 PID: 4315 Comm: rmmod Tainted: G B 5.1.0-rc2+ #19
Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS 0.0.0 02/06/2015
Call Trace:
dump_stack+0x46/0x5b
slab_err+0xad/0xd0
? on_each_cpu_mask+0x3c/0x50
? ksm_migrate_page+0x60/0x60
? on_each_cpu_cond_mask+0x7c/0xa0
? __kmalloc+0x1ca/0x1e0
__kmem_cache_shutdown+0x13a/0x310
shutdown_cache+0xf/0x130
kmem_cache_destroy+0x1d5/0x200
kvm_mmu_module_exit+0xa/0x30 [kvm]
kvm_arch_exit+0x45/0x60 [kvm]
kvm_exit+0x6f/0x80 [kvm]
vmx_exit+0x1a/0x50 [kvm_intel]
__x64_sys_delete_module+0x153/0x1f0
? exit_to_usermode_loop+0x88/0xc0
do_syscall_64+0x4f/0x100
entry_SYSCALL_64_after_hwframe+0x44/0xa9
Fixes: a21136345cb6f ("KVM: x86/mmu: Split remote_flush+zap case out of kvm_mmu_flush_or_zap()")
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Linus Torvalds [Sun, 14 Apr 2019 22:17:41 +0000 (15:17 -0700)]
Linux 5.1-rc5
Linus Torvalds [Sun, 14 Apr 2019 22:09:40 +0000 (15:09 -0700)]
Merge branch 'page-refs' (page ref overflow)
Merge page ref overflow branch.
Jann Horn reported that he can overflow the page ref count with
sufficient memory (and a filesystem that is intentionally extremely
slow).
Admittedly it's not exactly easy. To have more than four billion
references to a page requires a minimum of 32GB of kernel memory just
for the pointers to the pages, much less any metadata to keep track of
those pointers. Jann needed a total of 140GB of memory and a specially
crafted filesystem that leaves all reads pending (in order to not ever
free the page references and just keep adding more).
Still, we have a fairly straightforward way to limit the two obvious
user-controllable sources of page references: direct-IO like page
references gotten through get_user_pages(), and the splice pipe page
duplication. So let's just do that.
* branch page-refs:
fs: prevent page refcount overflow in pipe_buf_get
mm: prevent get_user_pages() from overflowing page refcount
mm: add 'try_get_page()' helper function
mm: make page ref count overflow check tighter and more explicit
David S. Miller [Sun, 14 Apr 2019 22:07:30 +0000 (15:07 -0700)]
Merge tag 'mlx5-fixes-2019-04-09' of git://git./linux/kernel/git/saeed/linux
Saeed Mahameed says:
====================
Mellanox, mlx5 fixes 2019-04-09
This series provides some fixes to mlx5 driver.
I've cc'ed some of the checksum fixes to Eric Dumazet and i would like to get
his feedback before you pull.
For -stable v4.19
('net/mlx5: FPGA, tls, idr remove on flow delete')
('net/mlx5: FPGA, tls, hold rcu read lock a bit longer')
For -stable v4.20
('net/mlx5e: Rx, Check ip headers sanity')
('Revert "net/mlx5e: Enable reporting checksum unnecessary also for L3 packets"')
('net/mlx5e: Rx, Fixup skb checksum for packets with tail padding')
For -stable v5.0
('net/mlx5e: Switch to Toeplitz RSS hash by default')
('net/mlx5e: Protect against non-uplink representor for encap')
('net/mlx5e: XDP, Avoid checksum complete when XDP prog is loaded')
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Sun, 14 Apr 2019 18:02:05 +0000 (11:02 -0700)]
rtnetlink: fix rtnl_valid_stats_req() nlmsg_len check
Jakub forgot to either use nlmsg_len() or nlmsg_msg_size(),
allowing KMSAN to detect a possible uninit-value in rtnl_stats_get
BUG: KMSAN: uninit-value in rtnl_stats_get+0x6d9/0x11d0 net/core/rtnetlink.c:4997
CPU: 0 PID: 10428 Comm: syz-executor034 Not tainted 5.1.0-rc2+ #24
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
Call Trace:
__dump_stack lib/dump_stack.c:77 [inline]
dump_stack+0x173/0x1d0 lib/dump_stack.c:113
kmsan_report+0x131/0x2a0 mm/kmsan/kmsan.c:619
__msan_warning+0x7a/0xf0 mm/kmsan/kmsan_instr.c:310
rtnl_stats_get+0x6d9/0x11d0 net/core/rtnetlink.c:4997
rtnetlink_rcv_msg+0x115b/0x1550 net/core/rtnetlink.c:5192
netlink_rcv_skb+0x431/0x620 net/netlink/af_netlink.c:2485
rtnetlink_rcv+0x50/0x60 net/core/rtnetlink.c:5210
netlink_unicast_kernel net/netlink/af_netlink.c:1310 [inline]
netlink_unicast+0xf3e/0x1020 net/netlink/af_netlink.c:1336
netlink_sendmsg+0x127f/0x1300 net/netlink/af_netlink.c:1925
sock_sendmsg_nosec net/socket.c:622 [inline]
sock_sendmsg net/socket.c:632 [inline]
___sys_sendmsg+0xdb3/0x1220 net/socket.c:2137
__sys_sendmsg net/socket.c:2175 [inline]
__do_sys_sendmsg net/socket.c:2184 [inline]
__se_sys_sendmsg+0x305/0x460 net/socket.c:2182
__x64_sys_sendmsg+0x4a/0x70 net/socket.c:2182
do_syscall_64+0xbc/0xf0 arch/x86/entry/common.c:291
entry_SYSCALL_64_after_hwframe+0x63/0xe7
Fixes: 51bc860d4a99 ("rtnetlink: stats: validate attributes in get as well as dumps")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: syzbot <syzkaller@googlegroups.com>
Cc: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Sun, 14 Apr 2019 20:59:49 +0000 (13:59 -0700)]
Merge branch 'qed-doorbell-overflow-recovery'
Denis Bolotin says:
====================
qed: Fix the Doorbell Overflow Recovery mechanism
This patch series fixes and improves the doorbell recovery mechanism.
The main goals of this series are to fix missing attentions from the
doorbells block (DORQ) or not handling them properly, and execute the
recovery from periodic handler instead of the attention handler.
Please consider applying the series to net.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Denis Bolotin [Sun, 14 Apr 2019 14:23:08 +0000 (17:23 +0300)]
qed: Fix the DORQ's attentions handling
Separate the overflow handling from the hardware interrupt status analysis.
The interrupt status is a single register and is common for all PFs. The
first PF reading the register is not necessarily the one who overflowed.
All PFs must check their overflow status on every attention.
In this change we clear the sticky indication in the attention handler to
allow doorbells to be processed again as soon as possible, but running
the doorbell recovery is scheduled for the periodic handler to reduce the
time spent in the attention handler.
Checking the need for DORQ flush was changed to "db_bar_no_edpm" because
qed_edpm_enabled()'s result could change dynamically and might have
prevented a needed flush.
Signed-off-by: Denis Bolotin <dbolotin@marvell.com>
Signed-off-by: Michal Kalderon <mkalderon@marvell.com>
Signed-off-by: Ariel Elior <aelior@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Denis Bolotin [Sun, 14 Apr 2019 14:23:07 +0000 (17:23 +0300)]
qed: Fix missing DORQ attentions
When the DORQ (doorbell block) is overflowed, all PFs get attentions at the
same time. If one PF finished handling the attention before another PF even
started, the second PF might miss the DORQ's attention bit and not handle
the attention at all.
If the DORQ attention is missed and the issue is not resolved, another
attention will not be sent, therefore each attention is treated as a
potential DORQ attention.
As a result, the attention callback is called more frequently so the debug
print was moved to reduce its quantity.
The number of periodic doorbell recovery handler schedules was reduced
because it was the previous way to mitigating the missed attention issue.
Signed-off-by: Denis Bolotin <dbolotin@marvell.com>
Signed-off-by: Michal Kalderon <mkalderon@marvell.com>
Signed-off-by: Ariel Elior <aelior@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Denis Bolotin [Sun, 14 Apr 2019 14:23:06 +0000 (17:23 +0300)]
qed: Fix the doorbell address sanity check
Fix the condition which verifies that doorbell address is inside the
doorbell bar by checking that the end of the address is within range
as well.
Signed-off-by: Denis Bolotin <dbolotin@marvell.com>
Signed-off-by: Michal Kalderon <mkalderon@marvell.com>
Signed-off-by: Ariel Elior <aelior@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Denis Bolotin [Sun, 14 Apr 2019 14:23:05 +0000 (17:23 +0300)]
qed: Delete redundant doorbell recovery types
DB_REC_DRY_RUN (running doorbell recovery without sending doorbells) is
never used. DB_REC_ONCE (send a single doorbell from the doorbell recovery)
is not needed anymore because by running the periodic handler we make sure
we check the overflow status later instead.
This patch is needed because in the next patches, the only doorbell
recovery type being used is DB_REC_REAL_DEAL, and the fixes are much
cleaner without this enum.
Signed-off-by: Denis Bolotin <dbolotin@marvell.com>
Signed-off-by: Michal Kalderon <mkalderon@marvell.com>
Signed-off-by: Ariel Elior <aelior@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Sun, 14 Apr 2019 00:32:21 +0000 (17:32 -0700)]
ipv4: ensure rcu_read_lock() in ipv4_link_failure()
fib_compute_spec_dst() needs to be called under rcu protection.
syzbot reported :
WARNING: suspicious RCU usage
5.1.0-rc4+ #165 Not tainted
include/linux/inetdevice.h:220 suspicious rcu_dereference_check() usage!
other info that might help us debug this:
rcu_scheduler_active = 2, debug_locks = 1
1 lock held by swapper/0/0:
#0:
0000000051b67925 ((&n->timer)){+.-.}, at: lockdep_copy_map include/linux/lockdep.h:170 [inline]
#0:
0000000051b67925 ((&n->timer)){+.-.}, at: call_timer_fn+0xda/0x720 kernel/time/timer.c:1315
stack backtrace:
CPU: 0 PID: 0 Comm: swapper/0 Not tainted 5.1.0-rc4+ #165
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
Call Trace:
<IRQ>
__dump_stack lib/dump_stack.c:77 [inline]
dump_stack+0x172/0x1f0 lib/dump_stack.c:113
lockdep_rcu_suspicious+0x153/0x15d kernel/locking/lockdep.c:5162
__in_dev_get_rcu include/linux/inetdevice.h:220 [inline]
fib_compute_spec_dst+0xbbd/0x1030 net/ipv4/fib_frontend.c:294
spec_dst_fill net/ipv4/ip_options.c:245 [inline]
__ip_options_compile+0x15a7/0x1a10 net/ipv4/ip_options.c:343
ipv4_link_failure+0x172/0x400 net/ipv4/route.c:1195
dst_link_failure include/net/dst.h:427 [inline]
arp_error_report+0xd1/0x1c0 net/ipv4/arp.c:297
neigh_invalidate+0x24b/0x570 net/core/neighbour.c:995
neigh_timer_handler+0xc35/0xf30 net/core/neighbour.c:1081
call_timer_fn+0x190/0x720 kernel/time/timer.c:1325
expire_timers kernel/time/timer.c:1362 [inline]
__run_timers kernel/time/timer.c:1681 [inline]
__run_timers kernel/time/timer.c:1649 [inline]
run_timer_softirq+0x652/0x1700 kernel/time/timer.c:1694
__do_softirq+0x266/0x95a kernel/softirq.c:293
invoke_softirq kernel/softirq.c:374 [inline]
irq_exit+0x180/0x1d0 kernel/softirq.c:414
exiting_irq arch/x86/include/asm/apic.h:536 [inline]
smp_apic_timer_interrupt+0x14a/0x570 arch/x86/kernel/apic/apic.c:1062
apic_timer_interrupt+0xf/0x20 arch/x86/entry/entry_64.S:807
Fixes: ed0de45a1008 ("ipv4: recompile ip options in ipv4_link_failure")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: syzbot <syzkaller@googlegroups.com>
Cc: Stephen Suryaputra <ssuryaextr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Matthew Wilcox [Fri, 5 Apr 2019 21:02:10 +0000 (14:02 -0700)]
fs: prevent page refcount overflow in pipe_buf_get
Change pipe_buf_get() to return a bool indicating whether it succeeded
in raising the refcount of the page (if the thing in the pipe is a page).
This removes another mechanism for overflowing the page refcount. All
callers converted to handle a failure.
Reported-by: Jann Horn <jannh@google.com>
Signed-off-by: Matthew Wilcox <willy@infradead.org>
Cc: stable@kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Thu, 11 Apr 2019 17:49:19 +0000 (10:49 -0700)]
mm: prevent get_user_pages() from overflowing page refcount
If the page refcount wraps around past zero, it will be freed while
there are still four billion references to it. One of the possible
avenues for an attacker to try to make this happen is by doing direct IO
on a page multiple times. This patch makes get_user_pages() refuse to
take a new page reference if there are already more than two billion
references to the page.
Reported-by: Jann Horn <jannh@google.com>
Acked-by: Matthew Wilcox <willy@infradead.org>
Cc: stable@kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Thu, 11 Apr 2019 17:14:59 +0000 (10:14 -0700)]
mm: add 'try_get_page()' helper function
This is the same as the traditional 'get_page()' function, but instead
of unconditionally incrementing the reference count of the page, it only
does so if the count was "safe". It returns whether the reference count
was incremented (and is marked __must_check, since the caller obviously
has to be aware of it).
Also like 'get_page()', you can't use this function unless you already
had a reference to the page. The intent is that you can use this
exactly like get_page(), but in situations where you want to limit the
maximum reference count.
The code currently does an unconditional WARN_ON_ONCE() if we ever hit
the reference count issues (either zero or negative), as a notification
that the conditional non-increment actually happened.
NOTE! The count access for the "safety" check is inherently racy, but
that doesn't matter since the buffer we use is basically half the range
of the reference count (ie we look at the sign of the count).
Acked-by: Matthew Wilcox <willy@infradead.org>
Cc: Jann Horn <jannh@google.com>
Cc: stable@kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Thu, 11 Apr 2019 17:06:20 +0000 (10:06 -0700)]
mm: make page ref count overflow check tighter and more explicit
We have a VM_BUG_ON() to check that the page reference count doesn't
underflow (or get close to overflow) by checking the sign of the count.
That's all fine, but we actually want to allow people to use a "get page
ref unless it's already very high" helper function, and we want that one
to use the sign of the page ref (without triggering this VM_BUG_ON).
Change the VM_BUG_ON to only check for small underflows (or _very_ close
to overflowing), and ignore overflows which have strayed into negative
territory.
Acked-by: Matthew Wilcox <willy@infradead.org>
Cc: Jann Horn <jannh@google.com>
Cc: stable@kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Sat, 13 Apr 2019 23:23:16 +0000 (16:23 -0700)]
Merge tag 'for-linus-
20190412' of git://git.kernel.dk/linux-block
Pull block fixes from Jens Axboe:
"Set of fixes that should go into this round. This pull is larger than
I'd like at this time, but there's really no specific reason for that.
Some are fixes for issues that went into this merge window, others are
not. Anyway, this contains:
- Hardware queue limiting for virtio-blk/scsi (Dongli)
- Multi-page bvec fixes for lightnvm pblk
- Multi-bio dio error fix (Jason)
- Remove the cache hint from the io_uring tool side, since we didn't
move forward with that (me)
- Make io_uring SETUP_SQPOLL root restricted (me)
- Fix leak of page in error handling for pc requests (Jérôme)
- Fix BFQ regression introduced in this merge window (Paolo)
- Fix break logic for bio segment iteration (Ming)
- Fix NVMe cancel request error handling (Ming)
- NVMe pull request with two fixes (Christoph):
- fix the initial CSN for nvme-fc (James)
- handle log page offsets properly in the target (Keith)"
* tag 'for-linus-
20190412' of git://git.kernel.dk/linux-block:
block: fix the return errno for direct IO
nvmet: fix discover log page when offsets are used
nvme-fc: correct csn initialization and increments on error
block: do not leak memory in bio_copy_user_iov()
lightnvm: pblk: fix crash in pblk_end_partial_read due to multipage bvecs
nvme: cancel request synchronously
blk-mq: introduce blk_mq_complete_request_sync()
scsi: virtio_scsi: limit number of hw queues by nr_cpu_ids
virtio-blk: limit number of hw queues by nr_cpu_ids
block, bfq: fix use after free in bfq_bfqq_expire
io_uring: restrict IORING_SETUP_SQPOLL to root
tools/io_uring: remove IOCQE_FLAG_CACHEHIT
block: don't use for-inside-for in bio_for_each_segment_all
Linus Torvalds [Sat, 13 Apr 2019 21:47:06 +0000 (14:47 -0700)]
Merge tag 'nfs-for-5.1-4' of git://git.linux-nfs.org/projects/trondmy/linux-nfs
Pull NFS client bugfixes from Trond Myklebust:
"Highlights include:
Stable fix:
- Fix a deadlock in close() due to incorrect draining of RDMA queues
Bugfixes:
- Revert "SUNRPC: Micro-optimise when the task is known not to be
sleeping" as it is causing stack overflows
- Fix a regression where NFSv4 getacl and fs_locations stopped
working
- Forbid setting AF_INET6 to "struct sockaddr_in"->sin_family.
- Fix xfstests failures due to incorrect copy_file_range() return
values"
* tag 'nfs-for-5.1-4' of git://git.linux-nfs.org/projects/trondmy/linux-nfs:
Revert "SUNRPC: Micro-optimise when the task is known not to be sleeping"
NFSv4.1 fix incorrect return value in copy_file_range
xprtrdma: Fix helper that drains the transport
NFS: Fix handling of reply page vector
NFS: Forbid setting AF_INET6 to "struct sockaddr_in"->sin_family.
Linus Torvalds [Sat, 13 Apr 2019 21:37:49 +0000 (14:37 -0700)]
Merge tag 'scsi-fixes' of git://git./linux/kernel/git/jejb/scsi
Pull SCSI fix from James Bottomley:
"One obvious fix for a ciostor data corruption on error bug"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: csiostor: fix missing data copy in csio_scsi_err_handler()
Linus Torvalds [Sat, 13 Apr 2019 21:33:56 +0000 (14:33 -0700)]
Merge tag 'clk-fixes-for-linus' of git://git./linux/kernel/git/clk/linux
Pull clk fixes from Stephen Boyd:
"Here's more than a handful of clk driver fixes for changes that came
in during the merge window:
- Fix the AT91 sama5d2 programmable clk prescaler formula
- A bunch of Amlogic meson clk driver fixes for the VPU clks
- A DMI quirk for Intel's Bay Trail SoC's driver to properly mark pmc
clks as critical only when really needed
- Stop overwriting CLK_SET_RATE_PARENT flag in mediatek's clk gate
implementation
- Use the right structure to test for a frequency table in i.MX's
PLL_1416x driver"
* tag 'clk-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux:
clk: imx: Fix PLL_1416X not rounding rates
clk: mediatek: fix clk-gate flag setting
platform/x86: pmc_atom: Drop __initconst on dmi table
clk: x86: Add system specific quirk to mark clocks as critical
clk: meson: vid-pll-div: remove warning and return 0 on invalid config
clk: meson: pll: fix rounding and setting a rate that matches precisely
clk: meson-g12a: fix VPU clock parents
clk: meson: g12a: fix VPU clock muxes mask
clk: meson-gxbb: round the vdec dividers to closest
clk: at91: fix programmable clock for sama5d2
Linus Torvalds [Sat, 13 Apr 2019 21:29:21 +0000 (14:29 -0700)]
Merge tag 'pci-v5.1-fixes-2' of git://git./linux/kernel/git/helgaas/pci
Pull PCI fixes from Bjorn Helgaas:
- Add a DMA alias quirk for another Marvell SATA device (Andre
Przywara)
- Fix a pciehp regression that broke safe removal of devices (Sergey
Miroshnichenko)
* tag 'pci-v5.1-fixes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci:
PCI: pciehp: Ignore Link State Changes after powering off a slot
PCI: Add function 1 DMA alias quirk for Marvell 9170 SATA controller
Linus Torvalds [Sat, 13 Apr 2019 16:03:09 +0000 (09:03 -0700)]
Merge tag 'powerpc-5.1-5' of git://git./linux/kernel/git/powerpc/linux
Pull powerpc fixes from Michael Ellerman:
"A minor build fix for 64-bit FLATMEM configs.
A fix for a boot failure on 32-bit powermacs.
My commit to fix CLOCK_MONOTONIC across Y2038 broke the 32-bit VDSO on
64-bit kernels, ie. compat mode, which is only used on big endian.
The rewrite of the SLB code we merged in 4.20 missed the fact that the
0x380 exception is also used with the Radix MMU to report out of range
accesses. This could lead to an oops if userspace tried to read from
addresses outside the user or kernel range.
Thanks to: Aneesh Kumar K.V, Christophe Leroy, Larry Finger, Nicholas
Piggin"
* tag 'powerpc-5.1-5' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
powerpc/mm: Define MAX_PHYSMEM_BITS for all 64-bit configs
powerpc/64s/radix: Fix radix segment exception handling
powerpc/vdso32: fix CLOCK_MONOTONIC on PPC64
powerpc/32: Fix early boot failure with RTAS built-in
Linus Torvalds [Sat, 13 Apr 2019 15:57:00 +0000 (08:57 -0700)]
Merge tag 'arm64-fixes' of git://git./linux/kernel/git/arm64/linux
Pull arm64 fixes from Will Deacon:
"The main thing is a fix to our FUTEX_WAKE_OP implementation which was
unbelievably broken, but did actually work for the one scenario that
GLIBC used to use.
Summary:
- Fix stack unwinding so we ignore user stacks
- Fix ftrace module PLT trampoline initialisation checks
- Fix terminally broken implementation of FUTEX_WAKE_OP atomics"
* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
arm64: futex: Fix FUTEX_WAKE_OP atomic ops with non-zero result value
arm64: backtrace: Don't bother trying to unwind the userspace stack
arm64/ftrace: fix inadvertent BUG() in trampoline check
Linus Torvalds [Sat, 13 Apr 2019 03:54:40 +0000 (20:54 -0700)]
Merge branch 'x86-urgent-for-linus' of git://git./linux/kernel/git/tip/tip
Pull x86 fixes from Ingo Molnar:
"Fix typos in user-visible resctrl parameters, and also fix assembly
constraint bugs that might result in miscompilation"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/asm: Use stricter assembly constraints in bitops
x86/resctrl: Fix typos in the mba_sc mount option
Linus Torvalds [Sat, 13 Apr 2019 03:52:28 +0000 (20:52 -0700)]
Merge branch 'timers-urgent-for-linus' of git://git./linux/kernel/git/tip/tip
Pull timer fix from Ingo Molnar:
"Fix the alarm_timer_remaining() return value"
* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
alarmtimer: Return correct remaining time
Linus Torvalds [Sat, 13 Apr 2019 03:50:43 +0000 (20:50 -0700)]
Merge branch 'sched-urgent-for-linus' of git://git./linux/kernel/git/tip/tip
Pull scheduler fix from Ingo Molnar:
"Fix a NULL pointer dereference crash in certain environments"
* 'sched-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
sched/fair: Do not re-read ->h_load_next during hierarchical load calculation
Linus Torvalds [Sat, 13 Apr 2019 03:42:30 +0000 (20:42 -0700)]
Merge branch 'perf-urgent-for-linus' of git://git./linux/kernel/git/tip/tip
Pull perf fixes from Ingo Molnar:
"Six kernel side fixes: three related to NMI handling on AMD systems, a
race fix, a kexec initialization fix and a PEBS sampling fix"
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
perf/core: Fix perf_event_disable_inatomic() race
x86/perf/amd: Remove need to check "running" bit in NMI handler
x86/perf/amd: Resolve NMI latency issues for active PMCs
x86/perf/amd: Resolve race condition when disabling PMC
perf/x86/intel: Initialize TFA MSR
perf/x86/intel: Fix handling of wakeup_events for multi-entry PEBS
Linus Torvalds [Sat, 13 Apr 2019 03:31:08 +0000 (20:31 -0700)]
Merge branch 'locking-urgent-for-linus' of git://git./linux/kernel/git/tip/tip
Pull locking fix from Ingo Molnar:
"Fixes a crash when accessing /proc/lockdep"
* 'locking-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
locking/lockdep: Zap lock classes even with lock debugging disabled
Linus Torvalds [Sat, 13 Apr 2019 03:21:59 +0000 (20:21 -0700)]
Merge branch 'irq-urgent-for-linus' of git://git./linux/kernel/git/tip/tip
Pull irq fixes from Ingo Molnar:
"Two genirq fixes, plus an irqchip driver error handling fix"
* 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
genirq: Respect IRQCHIP_SKIP_SET_WAKE in irq_chip_set_wake_parent()
genirq: Initialize request_mutex if CONFIG_SPARSE_IRQ=n
irqchip/irq-ls1x: Missing error code in ls1x_intc_of_init()
Linus Torvalds [Sat, 13 Apr 2019 03:13:13 +0000 (20:13 -0700)]
Merge branch 'core-urgent-for-linus' of git://git./linux/kernel/git/tip/tip
Pull core fixes from Ingo Molnar:
"Fix an objtool warning plus fix a u64_to_user_ptr() macro expansion
bug"
* 'core-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
objtool: Add rewind_stack_do_exit() to the noreturn list
linux/kernel.h: Use parentheses around argument in u64_to_user_ptr()
Stephen Suryaputra [Fri, 12 Apr 2019 20:19:27 +0000 (16:19 -0400)]
ipv4: recompile ip options in ipv4_link_failure
Recompile IP options since IPCB may not be valid anymore when
ipv4_link_failure is called from arp_error_report.
Refer to the commit
3da1ed7ac398 ("net: avoid use IPCB in cipso_v4_error")
and the commit before that (
9ef6b42ad6fd) for a similar issue.
Signed-off-by: Stephen Suryaputra <ssuryaextr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Fri, 12 Apr 2019 23:57:23 +0000 (16:57 -0700)]
Merge branch 'rxrpc-fixes'
David Howells says:
====================
rxrpc: Fixes
Here is a collection of fixes for rxrpc:
(1) rxrpc_error_report() needs to call sock_error() to clear the error
code from the UDP transport socket, lest it be unexpectedly revisited
on the next kernel_sendmsg() call. This has been causing all sorts of
weird effects in AFS as the effects have typically been felt by the
wrong RxRPC call.
(2) Allow a kernel user of AF_RXRPC to easily detect if an rxrpc call has
completed.
(3) Allow errors incurred by attempting to transmit data through the UDP
socket to get back up the stack to AFS.
(4) Make AFS use (2) to abort the synchronous-mode call waiting loop if
the rxrpc-level call completed.
(5) Add a missing tracepoint case for tracing abort reception.
(6) Fix detection and handling of out-of-order ACKs.
====================
Tested-by: Jonathan Billings <jsbillin@umich.edu>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jeffrey Altman [Fri, 12 Apr 2019 15:34:16 +0000 (16:34 +0100)]
rxrpc: Fix detection of out of order acks
The rxrpc packet serial number cannot be safely used to compute out of
order ack packets for several reasons:
1. The allocation of serial numbers cannot be assumed to imply the order
by which acks are populated and transmitted. In some rxrpc
implementations, delayed acks and ping acks are transmitted
asynchronously to the receipt of data packets and so may be transmitted
out of order. As a result, they can race with idle acks.
2. Serial numbers are allocated by the rxrpc connection and not the call
and as such may wrap independently if multiple channels are in use.
In any case, what matters is whether the ack packet provides new
information relating to the bounds of the window (the firstPacket and
previousPacket in the ACK data).
Fix this by discarding packets that appear to wind back the window bounds
rather than on serial number procession.
Fixes: 298bc15b2079 ("rxrpc: Only take the rwind and mtu values from latest ACK")
Signed-off-by: Jeffrey Altman <jaltman@auristor.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Tested-by: Marc Dionne <marc.dionne@auristor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David Howells [Fri, 12 Apr 2019 15:34:09 +0000 (16:34 +0100)]
rxrpc: Trace received connection aborts
Trace received calls that are aborted due to a connection abort, typically
because of authentication failure. Without this, connection aborts don't
show up in the trace log.
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Marc Dionne [Fri, 12 Apr 2019 15:34:02 +0000 (16:34 +0100)]
afs: Check for rxrpc call completion in wait loop
Check the state of the rxrpc call backing an afs call in each iteration of
the call wait loop in case the rxrpc call has already been terminated at
the rxrpc layer.
Interrupt the wait loop and mark the afs call as complete if the rxrpc
layer call is complete.
There were cases where rxrpc errors were not passed up to afs, which could
result in this loop waiting forever for an afs call to transition to
AFS_CALL_COMPLETE while the rx call was already complete.
Signed-off-by: Marc Dionne <marc.dionne@auristor.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Marc Dionne [Fri, 12 Apr 2019 15:33:54 +0000 (16:33 +0100)]
rxrpc: Allow errors to be returned from rxrpc_queue_packet()
Change rxrpc_queue_packet()'s signature so that it can return any error
code it may encounter when trying to send the packet.
This allows the caller to eventually do something in case of error - though
it should be noted that the packet has been queued and a resend is
scheduled.
Signed-off-by: Marc Dionne <marc.dionne@auristor.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Marc Dionne [Fri, 12 Apr 2019 15:33:47 +0000 (16:33 +0100)]
rxrpc: Make rxrpc_kernel_check_life() indicate if call completed
Make rxrpc_kernel_check_life() pass back the life counter through the
argument list and return true if the call has not yet completed.
Suggested-by: Marc Dionne <marc.dionne@auristor.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Marc Dionne [Fri, 12 Apr 2019 15:33:40 +0000 (16:33 +0100)]
rxrpc: Clear socket error
When an ICMP or ICMPV6 error is received, the error will be attached
to the socket (sk_err) and the report function will get called.
Clear any pending error here by calling sock_error().
This would cause the following attempt to use the socket to fail with
the error code stored by the ICMP error, resulting in unexpected errors
with various side effects depending on the context.
Signed-off-by: Marc Dionne <marc.dionne@auristor.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Tested-by: Jonathan Billings <jsbillin@umich.edu>
Signed-off-by: David S. Miller <davem@davemloft.net>
Colin Ian King [Fri, 12 Apr 2019 14:13:27 +0000 (15:13 +0100)]
qede: fix write to free'd pointer error and double free of ptp
The err2 error return path calls qede_ptp_disable that cleans up
on an error and frees ptp. After this, the free'd ptp is dereferenced
when ptp->clock is set to NULL and the code falls-through to error
path err1 that frees ptp again.
Fix this by calling qede_ptp_disable and exiting via an error
return path that does not set ptp->clock or kfree ptp.
Addresses-Coverity: ("Write to pointer after free")
Fixes: 035744975aec ("qede: Add support for PTP resource locking.")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Colin Ian King [Fri, 12 Apr 2019 13:45:12 +0000 (14:45 +0100)]
vxge: fix return of a free'd memblock on a failed dma mapping
Currently if a pci dma mapping failure is detected a free'd
memblock address is returned rather than a NULL (that indicates
an error). Fix this by ensuring NULL is returned on this error case.
Addresses-Coverity: ("Use after free")
Fixes: 528f727279ae ("vxge: code cleanup and reorganization")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Leonard Crestez [Fri, 12 Apr 2019 14:10:03 +0000 (14:10 +0000)]
clk: imx: Fix PLL_1416X not rounding rates
Code which initializes the "clk_init_data.ops" checks pll->rate_table
before that field is ever assigned to so it always picks
"clk_pll1416x_min_ops".
This breaks dynamic rate rounding for features such as cpufreq.
Fix by checking pll_clk->rate_table instead, here pll_clk refers to
the constant initialization data coming from per-soc clk driver.
Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
Fixes: 8646d4dcc7fb ("clk: imx: Add PLLs driver for imx8mm soc")
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Kalle Valo [Fri, 12 Apr 2019 18:34:27 +0000 (21:34 +0300)]
Merge tag 'iwlwifi-for-kalle-2019-04-03' of git://git./linux/kernel/git/iwlwifi/iwlwifi-fixes
Second batch of iwlwifi fixes intended for v5.1
* fix for a potential deadlock in the TX path;
* a fix for offloaded rate-control;
* support new PCI HW IDs which use a new FW;
Stanislaw Gruszka [Fri, 5 Apr 2019 11:42:56 +0000 (13:42 +0200)]
mt76x02: avoid status_list.lock and sta->rate_ctrl_lock dependency
Move ieee80211_tx_status_ext() outside of status_list lock section
in order to avoid locking dependency and possible deadlock reposed by
LOCKDEP in below warning.
Also do mt76_tx_status_lock() just before it's needed.
[ 440.224832] WARNING: possible circular locking dependency detected
[ 440.224833] 5.1.0-rc2+ #22 Not tainted
[ 440.224834] ------------------------------------------------------
[ 440.224835] kworker/u16:28/2362 is trying to acquire lock:
[ 440.224836]
0000000089b8cacf (&(&q->lock)->rlock#2){+.-.}, at: mt76_wake_tx_queue+0x4c/0xb0 [mt76]
[ 440.224842]
but task is already holding lock:
[ 440.224842]
000000002cfedc59 (&(&sta->lock)->rlock){+.-.}, at: ieee80211_stop_tx_ba_cb+0x32/0x1f0 [mac80211]
[ 440.224863]
which lock already depends on the new lock.
[ 440.224863]
the existing dependency chain (in reverse order) is:
[ 440.224864]
-> #3 (&(&sta->lock)->rlock){+.-.}:
[ 440.224869] _raw_spin_lock_bh+0x34/0x40
[ 440.224880] ieee80211_start_tx_ba_session+0xe4/0x3d0 [mac80211]
[ 440.224894] minstrel_ht_get_rate+0x45c/0x510 [mac80211]
[ 440.224906] rate_control_get_rate+0xc1/0x140 [mac80211]
[ 440.224918] ieee80211_tx_h_rate_ctrl+0x195/0x3c0 [mac80211]
[ 440.224930] ieee80211_xmit_fast+0x26d/0xa50 [mac80211]
[ 440.224942] __ieee80211_subif_start_xmit+0xfc/0x310 [mac80211]
[ 440.224954] ieee80211_subif_start_xmit+0x38/0x390 [mac80211]
[ 440.224956] dev_hard_start_xmit+0xb8/0x300
[ 440.224957] __dev_queue_xmit+0x7d4/0xbb0
[ 440.224968] ip6_finish_output2+0x246/0x860 [ipv6]
[ 440.224978] mld_sendpack+0x1bd/0x360 [ipv6]
[ 440.224987] mld_ifc_timer_expire+0x1a4/0x2f0 [ipv6]
[ 440.224989] call_timer_fn+0x89/0x2a0
[ 440.224990] run_timer_softirq+0x1bd/0x4d0
[ 440.224992] __do_softirq+0xdb/0x47c
[ 440.224994] irq_exit+0xfa/0x100
[ 440.224996] smp_apic_timer_interrupt+0x9a/0x220
[ 440.224997] apic_timer_interrupt+0xf/0x20
[ 440.224999] cpuidle_enter_state+0xc1/0x470
[ 440.225000] do_idle+0x21a/0x260
[ 440.225001] cpu_startup_entry+0x19/0x20
[ 440.225004] start_secondary+0x135/0x170
[ 440.225006] secondary_startup_64+0xa4/0xb0
[ 440.225007]
-> #2 (&(&sta->rate_ctrl_lock)->rlock){+.-.}:
[ 440.225009] _raw_spin_lock_bh+0x34/0x40
[ 440.225022] rate_control_tx_status+0x4f/0xb0 [mac80211]
[ 440.225031] ieee80211_tx_status_ext+0x142/0x1a0 [mac80211]
[ 440.225035] mt76x02_send_tx_status+0x2e4/0x340 [mt76x02_lib]
[ 440.225037] mt76x02_tx_status_data+0x31/0x40 [mt76x02_lib]
[ 440.225040] mt76u_tx_status_data+0x51/0xa0 [mt76_usb]
[ 440.225042] process_one_work+0x237/0x5d0
[ 440.225043] worker_thread+0x3c/0x390
[ 440.225045] kthread+0x11d/0x140
[ 440.225046] ret_from_fork+0x3a/0x50
[ 440.225047]
-> #1 (&(&list->lock)->rlock#8){+.-.}:
[ 440.225049] _raw_spin_lock_bh+0x34/0x40
[ 440.225052] mt76_tx_status_skb_add+0x51/0x100 [mt76]
[ 440.225054] mt76x02u_tx_prepare_skb+0xbd/0x116 [mt76x02_usb]
[ 440.225056] mt76u_tx_queue_skb+0x5f/0x180 [mt76_usb]
[ 440.225058] mt76_tx+0x93/0x190 [mt76]
[ 440.225070] ieee80211_tx_frags+0x148/0x210 [mac80211]
[ 440.225081] __ieee80211_tx+0x75/0x1b0 [mac80211]
[ 440.225092] ieee80211_tx+0xde/0x110 [mac80211]
[ 440.225105] __ieee80211_tx_skb_tid_band+0x72/0x90 [mac80211]
[ 440.225122] ieee80211_send_auth+0x1f3/0x360 [mac80211]
[ 440.225141] ieee80211_auth.cold.40+0x6c/0x100 [mac80211]
[ 440.225156] ieee80211_mgd_auth.cold.50+0x132/0x15f [mac80211]
[ 440.225171] cfg80211_mlme_auth+0x149/0x360 [cfg80211]
[ 440.225181] nl80211_authenticate+0x273/0x2e0 [cfg80211]
[ 440.225183] genl_family_rcv_msg+0x196/0x3a0
[ 440.225184] genl_rcv_msg+0x47/0x8e
[ 440.225185] netlink_rcv_skb+0x3a/0xf0
[ 440.225187] genl_rcv+0x24/0x40
[ 440.225188] netlink_unicast+0x16d/0x210
[ 440.225189] netlink_sendmsg+0x204/0x3b0
[ 440.225191] sock_sendmsg+0x36/0x40
[ 440.225193] ___sys_sendmsg+0x259/0x2b0
[ 440.225194] __sys_sendmsg+0x47/0x80
[ 440.225196] do_syscall_64+0x60/0x1f0
[ 440.225197] entry_SYSCALL_64_after_hwframe+0x49/0xbe
[ 440.225198]
-> #0 (&(&q->lock)->rlock#2){+.-.}:
[ 440.225200] lock_acquire+0xb9/0x1a0
[ 440.225202] _raw_spin_lock_bh+0x34/0x40
[ 440.225204] mt76_wake_tx_queue+0x4c/0xb0 [mt76]
[ 440.225215] ieee80211_agg_start_txq+0xe8/0x2b0 [mac80211]
[ 440.225225] ieee80211_stop_tx_ba_cb+0xb8/0x1f0 [mac80211]
[ 440.225235] ieee80211_ba_session_work+0x1c1/0x2f0 [mac80211]
[ 440.225236] process_one_work+0x237/0x5d0
[ 440.225237] worker_thread+0x3c/0x390
[ 440.225239] kthread+0x11d/0x140
[ 440.225240] ret_from_fork+0x3a/0x50
[ 440.225240]
other info that might help us debug this:
[ 440.225241] Chain exists of:
&(&q->lock)->rlock#2 --> &(&sta->rate_ctrl_lock)->rlock --> &(&sta->lock)->rlock
[ 440.225243] Possible unsafe locking scenario:
[ 440.225244] CPU0 CPU1
[ 440.225244] ---- ----
[ 440.225245] lock(&(&sta->lock)->rlock);
[ 440.225245] lock(&(&sta->rate_ctrl_lock)->rlock);
[ 440.225246] lock(&(&sta->lock)->rlock);
[ 440.225247] lock(&(&q->lock)->rlock#2);
[ 440.225248]
*** DEADLOCK ***
[ 440.225249] 5 locks held by kworker/u16:28/2362:
[ 440.225250] #0:
0000000048fcd291 ((wq_completion)phy0){+.+.}, at: process_one_work+0x1b5/0x5d0
[ 440.225252] #1:
00000000f1c6828f ((work_completion)(&sta->ampdu_mlme.work)){+.+.}, at: process_one_work+0x1b5/0x5d0
[ 440.225254] #2:
00000000433d2b2c (&sta->ampdu_mlme.mtx){+.+.}, at: ieee80211_ba_session_work+0x5c/0x2f0 [mac80211]
[ 440.225265] #3:
000000002cfedc59 (&(&sta->lock)->rlock){+.-.}, at: ieee80211_stop_tx_ba_cb+0x32/0x1f0 [mac80211]
[ 440.225276] #4:
000000009d7b9a44 (rcu_read_lock){....}, at: ieee80211_agg_start_txq+0x33/0x2b0 [mac80211]
[ 440.225286]
stack backtrace:
[ 440.225288] CPU: 2 PID: 2362 Comm: kworker/u16:28 Not tainted 5.1.0-rc2+ #22
[ 440.225289] Hardware name: LENOVO 20KGS23S0P/20KGS23S0P, BIOS N23ET55W (1.30 ) 08/31/2018
[ 440.225300] Workqueue: phy0 ieee80211_ba_session_work [mac80211]
[ 440.225301] Call Trace:
[ 440.225304] dump_stack+0x85/0xc0
[ 440.225306] print_circular_bug.isra.38.cold.58+0x15c/0x195
[ 440.225307] check_prev_add.constprop.48+0x5f0/0xc00
[ 440.225309] ? check_prev_add.constprop.48+0x39d/0xc00
[ 440.225311] ? __lock_acquire+0x41d/0x1100
[ 440.225312] __lock_acquire+0xd98/0x1100
[ 440.225313] ? __lock_acquire+0x41d/0x1100
[ 440.225315] lock_acquire+0xb9/0x1a0
[ 440.225317] ? mt76_wake_tx_queue+0x4c/0xb0 [mt76]
[ 440.225319] _raw_spin_lock_bh+0x34/0x40
[ 440.225321] ? mt76_wake_tx_queue+0x4c/0xb0 [mt76]
[ 440.225323] mt76_wake_tx_queue+0x4c/0xb0 [mt76]
[ 440.225334] ieee80211_agg_start_txq+0xe8/0x2b0 [mac80211]
[ 440.225344] ieee80211_stop_tx_ba_cb+0xb8/0x1f0 [mac80211]
[ 440.225354] ieee80211_ba_session_work+0x1c1/0x2f0 [mac80211]
[ 440.225356] process_one_work+0x237/0x5d0
[ 440.225358] worker_thread+0x3c/0x390
[ 440.225359] ? wq_calc_node_cpumask+0x70/0x70
[ 440.225360] kthread+0x11d/0x140
[ 440.225362] ? kthread_create_on_node+0x40/0x40
[ 440.225363] ret_from_fork+0x3a/0x50
Cc: stable@vger.kernel.org
Fixes: 88046b2c9f6d ("mt76: add support for reporting tx status with skb")
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Acked-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Vijayakumar Durai [Wed, 27 Mar 2019 10:03:17 +0000 (11:03 +0100)]
rt2x00: do not increment sequence number while re-transmitting
Currently rt2x00 devices retransmit the management frames with
incremented sequence number if hardware is assigning the sequence.
This is HW bug fixed already for non-QOS data frames, but it should
be fixed for management frames except beacon.
Without fix retransmitted frames have wrong SN:
AlphaNet_e8:fb:36 Vivotek_52:31:51 Authentication, SN=1648, FN=0, Flags=........C Frame is not being retransmitted 1648 1
AlphaNet_e8:fb:36 Vivotek_52:31:51 Authentication, SN=1649, FN=0, Flags=....R...C Frame is being retransmitted 1649 1
AlphaNet_e8:fb:36 Vivotek_52:31:51 Authentication, SN=1650, FN=0, Flags=....R...C Frame is being retransmitted 1650 1
With the fix SN stays correctly the same:
88:6a:e3:e8:f9:a2 8c:f5:a3:88:76:87 Authentication, SN=1450, FN=0, Flags=........C
88:6a:e3:e8:f9:a2 8c:f5:a3:88:76:87 Authentication, SN=1450, FN=0, Flags=....R...C
88:6a:e3:e8:f9:a2 8c:f5:a3:88:76:87 Authentication, SN=1450, FN=0, Flags=....R...C
Cc: stable@vger.kernel.org
Signed-off-by: Vijayakumar Durai <vijayakumar.durai1@vivint.com>
[sgruszka: simplify code, change comments and changelog]
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Felix Fietkau [Tue, 26 Mar 2019 08:34:21 +0000 (09:34 +0100)]
mt76: mt7603: send BAR after powersave wakeup
Now that the sequence number allocation is fixed, we can finally send a BAR
at powersave wakeup time to refresh the receiver side reorder window
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Felix Fietkau [Tue, 26 Mar 2019 08:34:20 +0000 (09:34 +0100)]
mt76: mt7603: fix sequence number assignment
If the MT_TXD3_SN_VALID flag is not set in the tx descriptor, the hardware
assigns the sequence number. However, the rest of the code assumes that the
sequence number specified in the 802.11 header gets transmitted.
This was causing issues with the aggregation setup, which worked for the
initial one (where the sequence numbers were still close), but not for
further teardown/re-establishing of sessions.
Additionally, the overwrite of the TID sequence number in WTBL2 was resetting
the hardware assigned sequence numbers, causing them to drift further apart.
Fix this by using the software assigned sequence numbers
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Felix Fietkau [Tue, 26 Mar 2019 08:34:19 +0000 (09:34 +0100)]
mt76: mt7603: add missing initialization for dev->ps_lock
Fixes lockdep complaint and a potential race condition
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
projects / openwrt / staging / blogic.git / log