Simon Glass [Tue, 11 Nov 2014 00:16:46 +0000 (17:16 -0700)]
dm: spl: Allow driver model to be used
When enabled, set up driver model for SPL. This allows SPL to use the same
drivers as the main U-Boot.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Tom Rini <trini@ti.com>
Simon Glass [Tue, 11 Nov 2014 00:16:45 +0000 (17:16 -0700)]
dm: spl: Make simple malloc() available when enabled
Set up the simple malloc() implementation when requested, in preference to
the full malloc().
Signed-off-by: Simon Glass <sjg@chromium.org>
Simon Glass [Tue, 11 Nov 2014 00:16:44 +0000 (17:16 -0700)]
dm: arm: spl: Allow simple malloc() in SPL
For SPL it is sometimes useful to have a simple malloc() just to permit
driver model to work, in the cases where the full malloc() is not made
available by the board config.
Signed-off-by: Simon Glass <sjg@chromium.org>
Simon Glass [Tue, 11 Nov 2014 00:16:43 +0000 (17:16 -0700)]
dm: Split the simple malloc() implementation into its own file
The simple malloc() implementation is used when memory is tight. It provides
a simple buffer with an incrementing pointer.
At present the implementation is inside dlmalloc. Move it into its own file
so that it is easier to find.
Rather than using relocation as a signal that the full malloc() is
available, add a special GD_FLG_FULL_MALLOC_INIT flag. This signals that the
simple malloc() should no longer be used.
In some cases, such as SPL, even the code space used by the full malloc() is
wasteful. Add a CONFIG_SYS_MALLOC_SIMPLE option to provide only the simple
malloc. In this case the full malloc is not available at all. It saves about
1KB of code space and about 0.5KB of data on Thumb 2.
Acked-by: Tom Rini <trini@ti.com>
Signed-off-by: Simon Glass <sjg@chromium.org>
Simon Glass [Tue, 11 Nov 2014 00:16:42 +0000 (17:16 -0700)]
dm: tegra: Avoid using arch-specific memcpy() in SPL
The faster functions are not actually available in SPL and the code size
likely isn't worth it. Use the normal memcpy() in SPL.
Signed-off-by: Simon Glass <sjg@chromium.org>
Simon Glass [Wed, 29 Oct 2014 19:09:03 +0000 (13:09 -0600)]
dm: serial: Support changing the baud rate
Implement this feature in the uclass so that the baudrate can be changed
with 'setenv baudrate <rate>'.
Signed-off-by: Simon Glass <sjg@chromium.org>
Simon Glass [Wed, 29 Oct 2014 19:09:02 +0000 (13:09 -0600)]
dm: at91: Add myself as maintainer for snapper9260
The old maintainer has left, so take this over.
Signed-off-by: Simon Glass <sjg@chromium.org>
Simon Glass [Wed, 29 Oct 2014 19:09:01 +0000 (13:09 -0600)]
dm: at91: Convert snapper9260 to use driver model
Convert this at91sam9260-based board to use driver model. This should serve
as an example for other similar boards. Serial and GPIO are supported so
far.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Andreas Bießmann <andreas.devel@googlemail.com>
Simon Glass [Wed, 29 Oct 2014 19:09:00 +0000 (13:09 -0600)]
dm: at91: Add driver model support for the serial driver
Add driver model support while retaining the existing legacy code. This
allows the driver to support boards that have converted to driver model
as well as those that have not.
Signed-off-by: Simon Glass <sjg@chromium.org>
Simon Glass [Wed, 29 Oct 2014 19:08:59 +0000 (13:08 -0600)]
dm: at91: Refactor serial driver slightly for driver model
Before adding driver model support, split out a few of the functions so
that they can be used by the driver model code.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Andreas Bießmann <andreas.devel@googlemail.com>
Simon Glass [Wed, 29 Oct 2014 19:08:58 +0000 (13:08 -0600)]
dm: at91: Add platform data for GPIO on at91sam9260-based boards
These boards all have the same GPIO arrangement, so add some common platform
data that can be used by all boards. Remove the configs which are no longer
required.
Signed-off-by: Simon Glass <sjg@chromium.org>
Simon Glass [Wed, 29 Oct 2014 19:08:57 +0000 (13:08 -0600)]
dm: at91: Add driver model support for atmel GPIO driver
Modify this driver to support driver model, with platform data required to
determine the GPIOs that it controls.
Signed-off-by: Simon Glass <sjg@chromium.org>
Simon Glass [Wed, 29 Oct 2014 19:08:56 +0000 (13:08 -0600)]
dm: at91: Move snapper9260 to generic baord
This works correctly, so switch it over before the deadline.
Signed-off-by: Simon Glass <sjg@chromium.org>
Simon Glass [Wed, 29 Oct 2014 19:08:55 +0000 (13:08 -0600)]
dm: at91: Correct text base for snapper9260
The value should be 0x21f00000. Fix it.
Signed-off-by: Simon Glass <sjg@chromium.org>
Tom Rini [Thu, 20 Nov 2014 04:18:29 +0000 (23:18 -0500)]
Merge branch 'master' of git://git.denx.de/u-boot-ubi
Tom Rini [Thu, 20 Nov 2014 04:18:19 +0000 (23:18 -0500)]
Merge branch 'master' of git://git.denx.de/u-boot-i2c
Tom Rini [Thu, 20 Nov 2014 04:17:13 +0000 (23:17 -0500)]
Merge branch 'master' of git://git.denx.de/u-boot-mpc5xxx
Stefan Roese [Wed, 19 Nov 2014 08:37:48 +0000 (09:37 +0100)]
powerpc: mpc52xx: Clear GD in the main U-Boot stage for SPL usage
When an MPC5200 based board is used with SPL support, the main
U-Boot needs to clear the GD (global data) struct again.
Otherwise the generic board init code in board_init_f (when
CONFIG_SYS_GENERIC_BOARD is defined) will not initialize all
GD variables correctly. Resulting in a hangup on the a4m2k
board.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Wolfgang Denk <wd@denx.de>
Stefan Roese [Wed, 19 Nov 2014 08:37:47 +0000 (09:37 +0100)]
powerpc: mpc52xx: a3m071/a4m2k: Convert to generic board
a3m071 and a4m2k share one config header. So adding the generic board defines
in this one file is enough to convert both boards.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Wolfgang Denk <wd@denx.de>
Stefan Roese [Wed, 19 Nov 2014 08:37:46 +0000 (09:37 +0100)]
powerpc: mpc52xx: a4m072: Convert to generic board
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Wolfgang Denk <wd@denx.de>
Dirk Eibach [Thu, 13 Nov 2014 18:21:18 +0000 (19:21 +0100)]
mpc83xx: Add gdsys hrcon board
The gdsys hrcon board is based on a Freescale MPC8308 SOC.
It boots from NOR-Flash, kernel and rootfs are stored on
SD-Card.
On board peripherals include:
- 1x GbE (optional)
- Lattice ECP3 FPGA connected via eLBC and PCIe
Signed-off-by: Dirk Eibach <dirk.eibach@gdsys.cc>
Signed-off-by: Stefan Roese <sr@denx.de>
Dirk Eibach [Thu, 13 Nov 2014 18:21:17 +0000 (19:21 +0100)]
board: iocon: Fix uninitialized access
Wolfgang Denk found this issue using cppcheck:
(error) Uninitialized variable: fpga_features
Signed-off-by: Dirk Eibach <dirk.eibach@gdsys.cc>
Signed-off-by: Stefan Roese <sr@denx.de>
Dirk Eibach [Thu, 13 Nov 2014 18:21:16 +0000 (19:21 +0100)]
board: iocon: Fix fpga index in print_fpga_info()
Signed-off-by: Dirk Eibach <dirk.eibach@gdsys.cc>
Signed-off-by: Stefan Roese <sr@denx.de>
Dirk Eibach [Thu, 13 Nov 2014 18:21:15 +0000 (19:21 +0100)]
board: dlvision-10g: Compile fix
Signed-off-by: Dirk Eibach <dirk.eibach@gdsys.cc>
Signed-off-by: Stefan Roese <sr@denx.de>
Dirk Eibach [Thu, 13 Nov 2014 18:21:14 +0000 (19:21 +0100)]
common: Fix cmd_fpgad addressing
Addressing was completely broken for cmd_fpgad.
Signed-off-by: Dirk Eibach <dirk.eibach@gdsys.cc>
Signed-off-by: Stefan Roese <sr@denx.de>
Dirk Eibach [Thu, 13 Nov 2014 18:21:13 +0000 (19:21 +0100)]
mtd: Handle 29LV800BT
The device id makes u-boot think that this chip needs
cfi_reverse_geometry(), which is not the case.
Add it to jedec_flash, so it is handled properly.
Signed-off-by: Dirk Eibach <dirk.eibach@gdsys.cc>
Signed-off-by: Stefan Roese <sr@denx.de>
Dirk Eibach [Thu, 13 Nov 2014 18:21:12 +0000 (19:21 +0100)]
board: dlvision: Reduce memory footprint
Tune dlvision configuration similar to other gdsys boards to reduce memory
footprint.
Signed-off-by: Dirk Eibach <dirk.eibach@gdsys.cc>
Signed-off-by: Stefan Roese <sr@denx.de>
Andrew Ruder [Wed, 5 Nov 2014 19:31:57 +0000 (13:31 -0600)]
ubi: enable error reporting in initialization
The UBI layer will disable much of its error reporting when it is
compiled into the linux kernel to avoid stopping boot. We want this
error reporting in U-Boot since we don't initialize the UBI layer until
it is used and want the error reporting.
We force this by telling the UBI layer we are building as a module.
Signed-off-by: Andrew Ruder <andrew.ruder@elecsyscorp.com>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Heiko Schocher <hs@denx.de>
Cc: Kyungmin Park <kmpark@infradead.org>
Heiko Schocher [Fri, 31 Oct 2014 10:29:45 +0000 (11:29 +0100)]
mtd, cfi, ubi: add missing writebufsize initialization
ff94bc40af3481d47546595ba73c136de6af6929 "mtd, ubi, ubifs: resync with Linux-3.14"
introduced the writebufsize field in struct mtd_info, which
is not initialized in the cfi_flash driver, which leads in
not working ubi on cfi flashes. Fix it
Signed-off-by: Heiko Schocher <hs@denx.de>
Reported-by: Andrew Ruder <andrew.ruder@elecsyscorp.com>
Acked-by: Stefan Roese <sr@denx.de>
Acked-by: Andrew Ruder <andrew.ruder@elecsyscorp.com>
Bo Shen [Mon, 10 Nov 2014 07:46:22 +0000 (15:46 +0800)]
ARM: atmel: add sama5d4 xplained ultra board support
The code for this board supports following features:
- Boot media support: NAND flash/SD card/SPI flash
- Support LCD display (optional, disabled by default)
- Support ethernet
- Support USB mass storage
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
Bo Shen [Mon, 10 Nov 2014 07:24:02 +0000 (15:24 +0800)]
ARM: atmel: add sama5d4ek board support
The code for this board supports following features:
- Boot media support: NAND flash/SD card/SPI flash
- Support LCD display
- Support ethernet
- Support USB mass storage
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
Bo Shen [Mon, 10 Nov 2014 07:24:01 +0000 (15:24 +0800)]
net: macb: enable GMAC IP without GE feature support
The User Register in GMAC IP is used to select interface type.
When with GE feature, it is used to select interface between
RGMII and GMII. If without GE feature, it is used to select
interface between MII and RMII.
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
Josh Wu [Mon, 10 Nov 2014 07:24:00 +0000 (15:24 +0800)]
mtd: atmel_nand: runtime to build gf table for pmecc
As in SAMA5D4 SoC, the gf table in ROM code can not be seen.
So, when we try to use PMECC, we need to build it when do
initialization.
Add a macro NO_GALOIS_TABLE_IN_ROM in soc header file. If it
is defined we will build gf table runtime.
The PMECC use the BCH algorithm, so based on the build_gf_tables()
function in lib/bch.c, we can build the Galois Field lookup table.
Signed-off-by: Josh Wu <josh.wu@atmel.com>
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
Heiko Schocher [Fri, 31 Oct 2014 07:31:06 +0000 (08:31 +0100)]
arm, spl, at91: add spl support for the corvus board
replaces the at91bootstrap code with SPL code.
make the spl image with:
./tools/mkimage -T atmelimage -d spl/u-boot-spl.bin spl/boot.bin
this writes the length of the spl image into the 6th
execption vector. This is needed from the ROM bootloader.
Signed-off-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Bo Shen <voice.shen@atmel.com>
Reviewed-by: Andreas Bießmann <andreas.devel@googlemail.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
Heiko Schocher [Fri, 31 Oct 2014 07:31:05 +0000 (08:31 +0100)]
arm, at91, spl: add spl support for the taurus board
replaces the at91bootstrap code with SPL code.
make the spl image with:
./tools/mkimage -T atmelimage -d spl/u-boot-spl.bin spl/boot.bin
this writes the length of the spl image into the 6th
execption vector. This is needed from the ROM bootloader.
Signed-off-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
Heiko Schocher [Fri, 31 Oct 2014 07:31:04 +0000 (08:31 +0100)]
arm, spl, at91: add at91sam9260 and at91sam9g45 spl support
add support for using spl code on at91sam9260 and at91sam9g45
based boards.
Signed-off-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Bo Shen <voice.shen@atmel.com>
Reviewed-by: Andreas Bießmann <andreas.devel@googlemail.com>
[adopt Bo's change in spl.c]
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
Heiko Schocher [Fri, 31 Oct 2014 07:31:03 +0000 (08:31 +0100)]
spl, mtd, nand, atmel_nand: invert device ready pin logic
device ready pin is signalling that the device is ready on state 1
not on 0. Simmiliar as it is in drivers/mtd/nand/nand_spl_simple.c
Signed-off-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Andreas Bießmann <andreas.devel@googlemail.com>
Reviewed-by: Bo Shen <voice.shen@atmel.com>
Acked-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
Heiko Schocher [Fri, 31 Oct 2014 07:31:02 +0000 (08:31 +0100)]
spl, nand, atmel_nand: add erase one block function
erase one nand block in spl code. keep it simple, as size matters
This is used on the upcoming taurus spl support.
Signed-off-by: Heiko Schocher <hs@denx.de>
Acked-by: Scott Wood <scottwood@freescale.com>
Reviewed-by: Bo Shen <voice.shen@atmel.com>
Reviewed-by: Andreas Bießmann <andreas.devel@googlemail.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
Heiko Schocher [Fri, 31 Oct 2014 07:31:01 +0000 (08:31 +0100)]
mtd: atmel_nand: add missing include
using this driver in SPL code with CONFIG_SPL_NAND_ECC
configured leads in an compileerror. Fix this.
Signed-off-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Andreas Bießmann <andreas.devel@googlemail.com>
Reviewed-by: Bo Shen <voice.shen@atmel.com>
[fix subject]
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
Heiko Schocher [Fri, 31 Oct 2014 07:31:00 +0000 (08:31 +0100)]
spl, nand: add option to boot raw u-boot.bin image only
enable to boot only a raw u-boot.bin image from nand with the
CONFIG_SPL_NAND_RAW_ONLY define. This option saves space on
boards where spl space is low.
Signed-off-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Andreas Bießmann <andreas.devel@googlemail.com>
Reviewed-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
Heiko Schocher [Fri, 31 Oct 2014 07:30:59 +0000 (08:30 +0100)]
arm, at91: add missing ddr2 cr register MPDDRC_CR_EBISHARE define
Signed-off-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
Heiko Schocher [Fri, 31 Oct 2014 07:30:58 +0000 (08:30 +0100)]
arm, at91: compile mpddrc ram init code also for AT91SAM9M10G45
- compile mpddrc ram init code also for AT91SAM9M10G45
based boards.
- in CONFIG_SAMA5D3 case, look for the ATMEL_MPDDRC_CR_DECOD_INTERLEAVED
in the cr configuration
Signed-off-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Andreas Bießmann <andreas.devel@googlemail.com>
Reviewed-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
Heiko Schocher [Fri, 31 Oct 2014 07:30:57 +0000 (08:30 +0100)]
arm, at91, mpddrc: fix typo in ddr2_init()
use the configure value for computing the ba_off value
not the value from the cr register. This leaded in a
wrong ram configuration on the upcoming corvus spl board
support.
Signed-off-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Andreas Bießmann <andreas.devel@googlemail.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
Heiko Schocher [Fri, 31 Oct 2014 07:30:56 +0000 (08:30 +0100)]
arm, at91: add spi dataflash support for the taurus board
Signed-off-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Bo Shen <voice.shen@atmel.com>
Reviewed-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
Heiko Schocher [Fri, 31 Oct 2014 07:30:55 +0000 (08:30 +0100)]
spi, atmel: move CONFIG_SYS_SPI_WRITE_TOUT into common header
move CONFIG_SYS_SPI_WRITE_TOUT into drivers/spi/atmel_spi.h
and define a default value. Delete this define in the board
config files, where it is possible (all boards use currently
the same value).
Signed-off-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
Reviewed-by: Andreas Bießmann <andreas.devel@googlemail.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
Heiko Schocher [Thu, 30 Oct 2014 08:59:59 +0000 (09:59 +0100)]
arm, at91: generate boot.bin file for all atmel SoC
generate the boot.bin file for all atmel SoC (arm920, arm926, armv7)
Signed-off-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Andreas Bießmann <andreas.devel@googlemail.com>
Reviewed-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
[fix subject]
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
Bo Shen [Fri, 24 Oct 2014 08:13:26 +0000 (16:13 +0800)]
ARM: atmel: spl: make css field configurable
The clock source for master clock can be slow clock, main clock,
plla clock or upll clock. So, make the clock source selection
field in mckr can be configured.
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
Bo Shen [Fri, 24 Oct 2014 08:13:25 +0000 (16:13 +0800)]
ARM: atmel: spl: make initialization more stable
We need to make sure the main clock ready field in MCFR is set
after switch to main crystal oscillator.
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
Bo Shen [Wed, 22 Oct 2014 10:01:23 +0000 (18:01 +0800)]
ARM: at91 series: convert to generic board
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Reviewed-by: Andreas Bießmann <andreas.devel@googlemail.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
Bo Shen [Wed, 22 Oct 2014 06:45:56 +0000 (14:45 +0800)]
net: macb: write mac address when initialization
When boot up without mac address setting, it will give the warning
message like: "Warning: failed to set MAC address", however when
execute network related command, it still execute them without any
warning information.
With this patch, it will exit directly with following information:
"gmac0: mac address is not valid"
It also solve the problem after bootup then set mac address and the
mac address won't set to net device issue.
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Tested-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
Tom Rini [Mon, 17 Nov 2014 13:43:40 +0000 (08:43 -0500)]
Merge branch 'master' of git://git.denx.de/u-boot-sh
Tom Rini [Mon, 17 Nov 2014 13:43:21 +0000 (08:43 -0500)]
Merge branch 'rmobile' of git://git.denx.de/u-boot-sh
Scott Jiang [Thu, 13 Nov 2014 07:30:55 +0000 (15:30 +0800)]
blackfin: convert to use CONFIG_SYS_I2C framework
Signed-off-by: Scott Jiang <scott.jiang.linux@gmail.com>
Scott Jiang [Thu, 13 Nov 2014 07:30:54 +0000 (15:30 +0800)]
adi_i2c: convert to use general io accessors.
Signed-off-by: Scott Jiang <scott.jiang.linux@gmail.com>
Scott Jiang [Thu, 13 Nov 2014 07:30:53 +0000 (15:30 +0800)]
blackfin: rename bfin-twi_i2c driver to adi_i2c
Signed-off-by: Scott Jiang <scott.jiang.linux@gmail.com>
Nobuhiro Iwamatsu [Mon, 10 Nov 2014 05:34:07 +0000 (14:34 +0900)]
arm: rmobile: replacement of common parts of config by rcar-gen2-common.h
Common part of config for lager, koelsch, alt and gose board will be able to
replace rcar-gen2-common.h.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Nobuhiro Iwamatsu [Thu, 6 Nov 2014 07:30:56 +0000 (16:30 +0900)]
arm: rmobile: configs: Collect up common part of config for R-Car SoCs
The lager, koelsch, alt, gose board supported in rmobile is
distinguished as the R-Car Gen2 series and has much common setting.
This collect up the common part of config as rcar-gen2-common.h.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Nobuhiro Iwamatsu [Mon, 10 Nov 2014 04:58:50 +0000 (13:58 +0900)]
arm: rmobile: gose: Remove dram_init_banksize function
Gose board is defined CONFIG_SYS_SDRAM_BASE, and this can use a basic function of
dram_init_banksize instead.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Nobuhiro Iwamatsu [Mon, 10 Nov 2014 04:58:50 +0000 (13:58 +0900)]
arm: rmobile: lager: Remove dram_init_banksize function
Lager board is defined CONFIG_SYS_SDRAM_BASE, and this can use a basic function of
dram_init_banksize instead.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Nobuhiro Iwamatsu [Mon, 10 Nov 2014 04:58:50 +0000 (13:58 +0900)]
arm: rmobile: koelsch: Remove dram_init_banksize function
Koesch board is defined CONFIG_SYS_SDRAM_BASE, and this can use a basic function of
dram_init_banksize instead.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Nobuhiro Iwamatsu [Mon, 10 Nov 2014 04:58:50 +0000 (13:58 +0900)]
arm: rmobile: alt: Remove dram_init_banksize function
Alt board is defined CONFIG_SYS_SDRAM_BASE, and this can use a basic function of
dram_init_banksize instead.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Nobuhiro Iwamatsu [Fri, 14 Nov 2014 03:52:47 +0000 (12:52 +0900)]
sh: Move SH_32BIT to Kconfig
This moves SH_32BIT to Kconfig, and removes SH_32BIT from config
files.
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Tom Rini [Fri, 14 Nov 2014 21:39:32 +0000 (16:39 -0500)]
Merge branch 'master' of git://git.denx.de/u-boot-mpc85xx
Tom Rini [Fri, 14 Nov 2014 20:05:53 +0000 (15:05 -0500)]
Merge branch 'master' of git://git.denx.de/u-boot-video
Yangbo Lu [Thu, 16 Oct 2014 02:58:55 +0000 (10:58 +0800)]
powerpc/85xx: enable some P1/P2 boards mtdparts for nor flash
Enable these boards mtdparts for nor flash:
p1020rdb-pd, p1021rdb-pc, p1022ds, p1025twr, and p2020rdb-pc.
Signed-off-by: Xie Xiaobo <X.Xie@freescale.com>
Signed-off-by: Yangbo Lu <yangbo.lu@freescale.com>
Cc: York Sun <yorksun@freescale.com>
Cc: Scott Wood <scottwood@freescale.com>
Valentin Longchamp [Fri, 3 Oct 2014 09:45:24 +0000 (11:45 +0200)]
keymile/powerpc: move to the architecture-generic board system
This converts all the Keymile powerpc boards to the generic board
initialization.
This includes the 3 Keymile powerpc subsystems: km82xx, km83xx,
and kmp204x.
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Valentin Longchamp [Fri, 3 Oct 2014 09:45:23 +0000 (11:45 +0200)]
powerpc/mpc83xx: Zero boot_flags arg for calling board_init_f()
The argument boot_flags of board_init_f() is not used at all in the
powerpc specific board.c init sequence. Now with the generic init
sequence, this boot_flags arg is used by board_init_f().
This patch sets the r3 register that is used to pass the boot_flags
argument from the start.S board_init_f() call to 0 prior to the function
call to avoid unknown content to end up in gd->flags.
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Ashish Kumar [Tue, 7 Oct 2014 12:32:23 +0000 (18:02 +0530)]
powerpc/BSC9131RDB: Enable creation of dynamic partitions for NAND
* fdt_fixup_mtdparts is called from ft_board_setup
* Run "mtdparts default" to create NAND partition on uboot
* Use mtdparts to create partitions dynamically rather
than using static partitions in device tree
Signed-off-by: Ashish Kumar <Ashish.Kumar@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Ashish Kumar [Mon, 6 Oct 2014 12:54:56 +0000 (18:24 +0530)]
powerpc/BSC9132QDS: Enable creation of dynamic partition for NAND and NOR
* fdt_fixup_mtdparts is called from ft_board_setup
* run "mtdparts default" to create NAND, NOR partition on uboot
* Use mtdparts to create partitions dynamically rather
than using static partitions in device tree
Signed-off-by: Ashish Kumar <Ashish.Kumar@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Prabhakar Kushwaha [Tue, 23 Sep 2014 05:27:12 +0000 (10:57 +0530)]
powerpc/mpc85xx: Use IFC accessor function
IFC registers can be of type Little Endian or big Endian depending upon
Freescale SoC. Here SoC defines the register type of IFC IP.
So use IFC acessor functions instead of in_be32().
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Priyanka Jain [Wed, 17 Sep 2014 10:27:54 +0000 (15:57 +0530)]
t104xrdb: Add Errata A_007662, A_008007 workaround in pbi.cfg
-A_007662 states that for x1 link width, PCIe2 controller trains in
Gen1 speed while configured for Gen2 speed.
Workaround:Set the width to x1 and speed to Gen2 by writing to
CCSR registers in PBI phase
-A_008007 states that PVR register may show random value.
Workaround: Reset PVR register using DCSR space in PBI phase
Add PBI based software workaround for A_007662 and A_008007
in t104x_pbi.cfg. This is required for SPL-based bootloaders
like NAND-boot, SD-boot, SPI-boot
Signed-off-by: Priyanka Jain <Priyanka.Jain@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Chunhe Lan [Fri, 12 Sep 2014 06:47:09 +0000 (14:47 +0800)]
powerpc/t4rdb: Add support of CPLD
This support of CPLD includes
- Files and register definitions
- Command to switch alternate bank
- Command to switch default bank
Signed-off-by: Chunhe Lan <Chunhe.Lan@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
ramneek mehresh [Thu, 21 Aug 2014 12:22:17 +0000 (17:52 +0530)]
85xx/b4:Correct USB DR controller liodn entry
LIODN entry for B4860/B4420 mentions USB controller as "mph"
insread of "dr". This results in PAMU not permitting bus
transactions for USB DR controller on B4860 resulting in
USB function failure. Replacing "fsl-usb2-mph" with
"fsl-usb2-dr" allows USB DR controller bus transactions
Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Signed-off-by: Ramneek Mehresh <ramneek.mehresh@freescale.com>
Reviewed-by: Sethi Varun-B16395 <Varun.Sethi@freescale.com>
Reviewed-by: Sun Yusong-R58495 <yorksun@freescale.com>
Paul Gortmaker [Thu, 14 Aug 2014 14:42:52 +0000 (10:42 -0400)]
sbc8548: enable and test CONFIG_SYS_GENERIC_BOARD
Tested on the following baseline (note "dirty" since I enabled
ALT_BOOT in the config in order to use the alternate boot bank.)
Everything seems to work fine with no additional changes. The
banner warning message is now gone.
---
U-Boot
2014.10-rc1-00075-ge49f14af1349-dirty (Aug 14 2014 - 10:26:15)
CPU: 8548E, Version: 2.1, (0x80390021)
Core: e500, Version: 2.2, (0x80210022)
Clock Configuration:
CPU0:990 MHz,
CCB:396 MHz,
DDR:198 MHz (396 MT/s data rate), LBC:99 MHz
L1: D-cache 32 KiB enabled
I-cache 32 KiB enabled
I2C: ready
DRAM: Detected UDIMM
SDRAM: 128 MiB
256 MiB (DDR2, 64-bit, CL=3, ECC off)
Flash: 72 MiB
L2: 512 KiB enabled
*** Warning - bad CRC, using default environment
PCI: Host, 64 bit, 66 MHz, sync, arbiter
00:01.0 - 8086:1026 - Network controller
PCI1: Bus 00 - 00
PCIe1: Root Complex, x1 gen1, regs @ 0xe000a000
02:00.0 - 1148:9e00 - Network controller
PCIe1: Bus 01 - 02
In: serial
Out: serial
Err: serial
Net: eTSEC0 [PRIME], eTSEC1
Hit any key to stop autoboot: 0
=> ver
U-Boot
2014.10-rc1-00075-ge49f14af1349-dirty (Aug 14 2014 - 10:26:15)
powerpc-linux-gcc (GCC) 4.5.2
GNU ld (GNU Binutils) 2.21
=>
---
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Shaohui Xie [Wed, 13 Aug 2014 10:38:09 +0000 (18:38 +0800)]
driver/net/fm/memac_phy: set NEG bit for external MDIOs
NEG bit default is '1' for external MDIOs as per FMAN-v3 RM, but on some
platforms, e.g. T2080QDS, this bit is '0', which leads to MDIO failure
on XAUI PHY, so set this bit definitely to align with the RM.
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Shaohui Xie [Wed, 13 Aug 2014 10:32:19 +0000 (18:32 +0800)]
Fman/mEMAC: mEMAC fix for 10G MAC and PHY
1. use Payload length check disable when enable MAC;
2. add XGMII support for setting MAC interface mode;
3. only enable auto negotiation for Non-XGMII mode;
4. return 0xffff if clause 22 is used to read 10G phy_id;
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Acked-By: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Valentin Longchamp [Fri, 24 Oct 2014 08:11:16 +0000 (10:11 +0200)]
mpc85xx/kmp204x: raise u-boot size to 768KB
Until now this defined to be 512KB and the total binary size actually
was on the edge of this limit. Most of the powerpc boards have thus
moved to 768KB.
Since on the current kmp204x boards there is 1MB reserved for u-boot on
the SPI boot flash, there is no problem to set the limit to 768KB as
well to be on line with the other powerpc boards and to eventually
configure in some additional features (and binary size) to u-boot.
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Tom Rini [Fri, 14 Nov 2014 18:53:49 +0000 (13:53 -0500)]
Merge branch 'master' of git://denx.de/git/u-boot-imx
Soeren Moch [Mon, 3 Nov 2014 12:57:01 +0000 (13:57 +0100)]
arm: mx6: add support for TBS2910 Matrix ARM miniPC
Add initial support for TBS2910 Matrix ARM miniPC.
Support includes MMC, Ethernet, UARTs, HDMI, USB, SATA, PCI, I2C, RTC.
Signed-off-by: Soeren Moch <smoch@web.de>
Fabio Estevam [Thu, 6 Nov 2014 14:24:25 +0000 (12:24 -0200)]
mx6sabresd: Staticize when possible
Annotate 'static' when appropriate for the variables used locally.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Fabio Estevam [Thu, 6 Nov 2014 14:24:24 +0000 (12:24 -0200)]
mx6sabresd: Fix error handling in board_mmc_init()
When an invalid USDHC port is passed we should return -EINVAL instead of 0.
Also, return the error immediately on fsl_esdhc_initialize() failure.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Nikolay Dimitrov [Wed, 5 Nov 2014 08:55:33 +0000 (10:55 +0200)]
mx6: video_skip: Fix crash on NULL pointer
Signed-off-by: Nikolay Dimitrov <picmaster@mail.bg>
Cc: Stefano Babic <sbabic@denx.de>
Tom Rini [Thu, 13 Nov 2014 15:35:13 +0000 (10:35 -0500)]
Merge branch 'master' of git://git.denx.de/u-boot-sunxi
John Tobias [Wed, 12 Nov 2014 22:27:45 +0000 (14:27 -0800)]
imx6: SPL support for iMX6 SabreSD
This patch will enable the support for SPL on iMX6 SabreSD.
It tested on SD2 and SD3 mmc port (Switch 1 or 2 of SW6)
Signed-off-by: John Tobias <john.tobias.ph@gmail.com>
Acked-by: Stefano Babic <sbabic@denx.de>
John Tobias [Wed, 12 Nov 2014 22:27:44 +0000 (14:27 -0800)]
imx6: add spl in the header file
add the spl info in the header file.
Also, added a macro statement in m6sabre_common.h to avoid compiler
warning.
Signed-off-by: John Tobias <john.tobias.ph@gmail.com>
John Tobias [Wed, 12 Nov 2014 22:27:43 +0000 (14:27 -0800)]
kconfig: imx6: add SUPPORT_SPL
add SUPPORT_SPL feature for iMX6 SabreSD. It need to use
mx6sabresd_spl_defconfig to compile it.
Signed-off-by: John Tobias <john.tobias.ph@gmail.com>
John Tobias [Wed, 12 Nov 2014 22:27:42 +0000 (14:27 -0800)]
imx6: add data configuration file for SPL
It's a trim version of mx6q_4x_mt41j128.cfg. It just removed
the related settings for DDR
Signed-off-by: John Tobias <john.tobias.ph@gmail.com>
John Tobias [Wed, 12 Nov 2014 22:27:41 +0000 (14:27 -0800)]
imx6: add spl config for mx6sabresd
add a build configuration file for mx6sabresd with spl support
Signed-off-by: John Tobias <john.tobias.ph@gmail.com>
Ye.Li [Wed, 12 Nov 2014 06:02:05 +0000 (14:02 +0800)]
imx: mx6q/dlsabreauto: And NAND flash support
The i.MX6Q/DL sabreauto board has one NAND socket, set the
CONFIG_NAND_MXS and relevant NAND configurations to enable the
MXS NAND flash driver.
Add board level codes to set IOMUX and clock for GPMI-NAND and
BCH module.
Signed-off-by: Ye.Li <B37916@freescale.com>
Reviewed-by: Fabio Estevam <fabio.estevam@freescale.com>
Ye.Li [Wed, 12 Nov 2014 06:02:04 +0000 (14:02 +0800)]
imx: mx6q/dl sabre_common: Move MMC ENV offset to 512KB position
Set the CONFIG_ENV_OFFSET from 384KB to 512KB offset, so we will have larger space
for u-boot image.
When enabling NAND flash support feature, the u-boot image size has exceeded the
384KB, which causes overlay to the environment variables storage.
Signed-off-by: Ye.Li <B37916@freescale.com>
Acked-by: Fabio Estevam <fabio.estevam@freescale.com>
Christian Gmeiner [Tue, 11 Nov 2014 11:57:05 +0000 (12:57 +0100)]
ot1200: fix card detect for usdhc4
Today I got the final board and found out that a different
connector is used as the one on my development board. The
new connector has swaped pins for cd and wp.
This change is tested on a production ready board.
Signed-off-by: Christian Gmeiner <christian.gmeiner@gmail.com>
Fabio Estevam [Mon, 10 Nov 2014 19:38:19 +0000 (17:38 -0200)]
mx53loco: Change 'fdt_file' dynamically
Since kernel 3.15 there are two dtb's for the imx53-qsb board:
imx53-qsb.dtb - For the boards with DA9053 PMIC
imx53-qsrb.dtb - For the boards with MC34708 PMIC
Change the 'fdt_file' dynamically, so that the correct dtb can be used depending
on the board variant.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Otavio Salvador <otavio@ossystems.com.br>
Christian Gmeiner [Mon, 10 Nov 2014 13:35:48 +0000 (14:35 +0100)]
ot1200: add support for EHCI
U-Boot
2014.10-17457-g0b23780-dirty (Nov 10 2014 - 11:41:04)
CPU: Freescale i.MX6D rev1.2 at 792 MHz
Reset cause: WDOG
Board: ot1200
I2C: ready
DRAM: 1 GiB
MMC: FSL_SDHC: 0, FSL_SDHC: 1
SF: Detected M25P16 with page size 256 Bytes, erase size 64 KiB, total 2 MiB
In: serial
Out: serial
Err: serial
Net: using phy at 0
FEC [PRIME]
Hit any key to stop autoboot: 0
=> usb start
(Re)start USB...
USB0: Port not available.
USB1: USB EHCI 1.00
scanning bus 1 for devices... 4 USB Device(s) found
=> usb tree
USB device tree:
1 Hub (480 Mb/s, 0mA)
| u-boot EHCI Host Controller
|
+-2 Hub (480 Mb/s, 2mA)
|
+-3 Mass Storage (480 Mb/s, 80mA)
| USBest Technology USB Mass Storage Device
0000000000028B
|
+-4 Vendor specific (480 Mb/s, 2mA)
=>
Signed-off-by: Christian Gmeiner <christian.gmeiner@gmail.com>
Tom Rini [Thu, 13 Nov 2014 14:32:45 +0000 (09:32 -0500)]
Merge branch 'master' of git://git.denx.de/u-boot-arm
Marek Vasut [Thu, 13 Nov 2014 10:06:21 +0000 (11:06 +0100)]
arm: mx6: Fix missing Kconfig option for Novena
Add two missing Kconfig options for Novena and drop the SPL
from the Novena config.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Sean Cross <xobs@kosagi.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Zoltan HERPAI [Tue, 11 Nov 2014 12:21:26 +0000 (13:21 +0100)]
sunxi: gmac: Update bananapi fixup to the new CONFIG_TARGET_<BOARD> structure
The magic bit toucher needs to be updated to reflect the new board Kconfig structure
Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Hans de Goede [Fri, 7 Nov 2014 13:51:12 +0000 (14:51 +0100)]
sun6i: ehci: Add sun6i ehci support
Add support for the 2 ehci controllers found on the sun6i (A31) soc.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Acked-by: Marek Vasut <marex@denx.de>
Hans de Goede [Fri, 7 Nov 2014 15:09:00 +0000 (16:09 +0100)]
sunxi: ehci: Add proper Kconfig options to select the usb Vbus gpio-s
Add proper Kconfig options to select the usb Vbus gpio-s, besides moving to
Kconfig being the right thing to do, an added advantage of this is that it
allows for boards without Vbus gpio-s.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Hans de Goede [Mon, 27 Oct 2014 22:29:49 +0000 (23:29 +0100)]
sun6i: Add Mele M9 board
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Hans de Goede [Sat, 25 Oct 2014 18:18:10 +0000 (20:18 +0200)]
sun6i: Enable SPL
Enable the SPL now that we've all the necessary bits in place.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
projects / project / bcm63xx / u-boot.git / log