ar71xx: fix port order on TP-Link Archer C60 v1/v2

The labels on the LAN ports of the TP-Link Archer C60 v1/v2 are
actually inverted compared to the ports of the internal switch.

Add this information to 02_network.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
(cherry picked from commit 14a07fa1f000f962d55bf53cfe9b128448b1f11f)

ar71xx: remove wrong MAC address adjustment for Archer C60 v2

The adjustment of the MAC address for Archer C60 v2 in 10_fix_wifi_mac
is broken since a "mac" partition is not set up for this device on
ar71xx. Instead, the MAC address is already patched correctly in
11-ath10k-caldata.

Remove the useless adjustment.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
(cherry picked from commit cbdc91902466dd113b9680566abb2eb2f8022dd4)

ar71xx: fix swapped LAN/WAN MAC address for Archer C60 v1/v2

The MAC addresses for lan/wan are swapped compared to the vendor
firmware. This adjusts to vendor configuration, which is:

lan   *:7b   label
wan   *:7c   label+1
2.4g  *:7b   label
5g    *:7a   label-1

Only one address is stored in <&mac 0x8>, corresponding to the label.

This has been checked on revisions v1, v2 and v3.

Since ar71xx calculates the ath10k MAC address based on the ethernet
addresses, the number there is adjusted, too.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
(cherry picked from commit 14eb54938b525d4c2d2847a6fad7670ed944650c)

ar71xx: ew-dorin, fix the trigger level for WPS button

Because the WPS button had the wrong trigger level,
the failsafe mode was triggered quite often,
after this commit:
https://git.openwrt.org/?p=openwrt/openwrt.git;a=commit;h=27f3f493de

Signed-off-by: Catrinel Catrinescu <cc@80211.de>
(cherry picked from commit 3e03b7ac4ada4966d058871d0a1f67f1f0f408d4)

kernel: backport out-of-memory fix for non-Ethernet devices

Doing up & down on non-Ethernet devices (e.g. monitor mode interface)
was consuming memory.

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
(cherry picked from commit ec8e8e2ef0826d82b4dfbd567a073b31dc27b764)

kernel: bump 4.14 to 4.14.172

Refreshed all patches.

Compile-tested on: cns3xxx
Runtime-tested on: cns3xxx

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>

kernel: bump 4.9 to 4.9.215

Refreshed all patches.

Compile-tested on: ar71xx
Runtime-tested on: ar71xx

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>

OpenWrt v18.06.8: revert to branch defaults

Signed-off-by: Jo-Philipp Wich <jo@mein.io>

OpenWrt v18.06.8: adjust config defaults

Signed-off-by: Jo-Philipp Wich <jo@mein.io>

libubox: backport blobmsg_check_array() fix

Fixes: FS#2833
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
(backported from commit 955634b473284847e3c8281a6ac85655329d8b06)

ppp: backport security fixes

8d45443bb5c9 pppd: Ignore received EAP messages when not doing EAP
8d7970b8f3db pppd: Fix bounds check in EAP code
858976b1fc31 radius: Prevent buffer overflow in rc_mksid()

Signed-off-by: Petr Štetiar <ynezz@true.cz>
(cherry picked from commit 215598fd03899c19a9cd26266221269dd5ec8cee)
Fixes: CVE-2020-8597
Signed-off-by: Jo-Philipp Wich <jo@mein.io>

Revert "ppp: backport security fixes"

This reverts commit cc78f934a9466a0ef404bb169cc42680c7501d02 since it
didn't contain a reference to the CVE it addresses. The next commit
will re-add the commit including a CVE reference in its commit message.

Signed-off-by: Jo-Philipp Wich <jo@mein.io>

uhttpd: update to latest Git HEAD

2ee323c file: poke ustream after starting deferred program

Signed-off-by: Jo-Philipp Wich <jo@mein.io>
(cherry picked from commit 04069fde19e86af7728111814afadf780bf08018)

kernel: bump 4.14 to 4.14.171

Refreshed all patches.

Fixes:
- CVE-2013-1798

Compile-tested on: cns3xxx
Runtime-tested on: cns3xxx

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>

kernel: bump 4.9 to 4.9.214

Refreshed all patches.

Fixes:
- CVE-2013-1798

Compile-tested on: ar71xx
Runtime-tested on: ar71xx

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>

ppp: backport security fixes

8d45443bb5c9 pppd: Ignore received EAP messages when not doing EAP
8d7970b8f3db pppd: Fix bounds check in EAP code
858976b1fc31 radius: Prevent buffer overflow in rc_mksid()

Signed-off-by: Petr Štetiar <ynezz@true.cz>
(cherry picked from commit 215598fd03899c19a9cd26266221269dd5ec8cee)

hostapd: remove erroneous $(space) redefinition

The $(space) definition in the hostapd Makefile ceased to work with
GNU Make 4.3 and later, leading to syntax errors in the generated
Kconfig files.

Drop the superfluous redefinition and reuse the working $(space)
declaration from rules.mk to fix this issue.

Fixes: GH#2713
Ref: https://github.com/openwrt/openwrt/pull/2713#issuecomment-583722469
Reported-by: Karel Kočí <cynerd@email.cz>
Suggested-by: Jonas Gorski <jonas.gorski@gmail.com>
Tested-by: Shaleen Jain <shaleen@jain.sh>
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
(backported from commit 766e778226f5d4c6ec49ce22b101a5dbd4306644)

kernel: add support for GD25D05 SPI NOR

This chip is used on newer RB912UAG-5HPnD r2 boards:

Before:

[    0.642553] m25p80 spi0.0: unrecognized JEDEC id bytes: c8, 40, 10
[    0.649381] NAND flash driver for the RouterBOARD 91x series

After:

[    0.641714] m25p80 spi0.0: found gd25d05, expected m25p80
[    0.649916] m25p80 spi0.0: gd25d05 (64 Kbytes)
[    0.655122] Creating 4 MTD partitions on "spi0.0":
[    0.660164] 0x000000000000-0x00000000c000 : "routerboot"
[    0.667782] 0x00000000c000-0x00000000d000 : "hard_config"
[    0.675073] 0x00000000d000-0x00000000e000 : "bios"
[    0.682613] 0x00000000e000-0x00000000f000 : "soft_config"
[    0.690304] NAND flash driver for the RouterBOARD 91x series

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>

kernel: bump 4.14 to 4.14.169

Refreshed all patches.

Fixes:
- CVE-2019-14896
- CVE-2019-14897

Remove upstreamed:
- 023-0007-crypto-crypto4xx-Fix-wrong-ppc4xx_trng_probe-ppc4xx_.patch

Altered patches:
- 102-MIPS-BCM63XX-move-code-touching-the-USB-private-regi.patch
- 105-MIPS-BCM63XX-add-support-for-the-on-chip-OHCI-contro.patch
- 106-MIPS-BCM63XX-register-OHCI-controller-if-board-enabl.patch
- 108-MIPS-BCM63XX-add-support-for-the-on-chip-EHCI-contro.patch
- 207-MIPS-BCM63XX-move-device-registration-code-into-its-.patch
- 350-MIPS-BCM63XX-support-settings-num-usbh-ports.patch
- 356-MIPS-BCM63XX-move-fallback-sprom-support-into-its-ow.patch
- 390-MIPS-BCM63XX-do-not-register-SPI-controllers.patch
- 391-MIPS-BCM63XX-do-not-register-uart.patch
- 392-MIPS-BCM63XX-remove-leds-and-buttons.patch
- 416-BCM63XX-add-a-fixup-for-ath9k-devices.patch
- 422-BCM63XX-add-a-fixup-for-rt2x00-devices.patch
-

Compile-tested on: brcm63xx, cns3xxx
Runtime-tested on: cns3xxx

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>

kernel: bump 4.9 to 4.9.212

Refreshed all patches.

Fixes:
- CVE-2019-14896
- CVE-2019-14897

Compile-tested on: ar71xx
Runtime-tested on: ar71xx

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>

OpenWrt v18.06.7: revert to branch defaults

Signed-off-by: Jo-Philipp Wich <jo@mein.io>

OpenWrt v18.06.7: adjust config defaults

Signed-off-by: Jo-Philipp Wich <jo@mein.io>

opkg: update to latest Git HEAD

80d161e opkg: Fix -Wformat-overflow warning
c09fe20 libopkg: fix skipping of leading whitespace when parsing checksums

Fixes: CVE-2020-7982
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
(cherry picked from commit c69c20c6670081d1eaab000734d89de57eb64148)

libubox: backport security patches

This backports some security relevant patches from libubox master. These
patches should not change the existing API and ABI so that old
applications still work like before without any recompilation.
Application can now also use more secure APIs.

The new more secure interfaces are also available, but not used.

OpenWrt master and 19.07 already have these patches by using a more
recent libubox version.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>

lantiq: ltq-ptm: vr9: fix skb handling in ptm_hard_start_xmit()

Call skb_orphan(skb) to call the owner's destructor function and make
the skb unowned.

This is necessary to prevent sk_wmem_alloc of a socket from overflowing,
which leads to ENOBUFS errors on application level.

Signed-off-by: Martin Schiller <ms@dev.tdt.de>
(cherry picked from commit 996f02e5bafad2815e72821c19d41fb5297e4dad)

tools/expat: Update to version 2.2.9

Fixes two CVEs:
- CVE-2019-15903 (Fix heap overflow triggered by XML_GetCurrentLineNumber)
- CVE-2018-20843 (Fix extraction of namespace prefixes from XML names)

Signed-off-by: Josef Schlehofer <pepe.schlehofer@gmail.com>
(cherry picked from commit b4af2c689fc8736777940b7bbf009bb1672296ec)

mbedtls: update to 2.16.4

Fixes side channel vulnerabilities in mbed TLS' implementation of ECDSA.

Release announcement:
https://tls.mbed.org/tech-updates/releases/mbedtls-2.16.4-and-2.7.13-released

Security advisory:
https://tls.mbed.org/tech-updates/security-advisories/mbedtls-security-advisory-2019-12

Fixes:
 * CVE-2019-18222: Side channel attack on ECDSA

Signed-off-by: Magnus Kroken <mkroken@gmail.com>
(cherry picked from commit 6e96fd90471a49185bcfe9dcb4844d444674ecab)

kernel: bump 4.14 to 4.14.167

Refreshed all patches.

Compile-tested on: cns3xxx
Runtime-tested on: cns3xxx

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>

kernel: bump 4.9 to 4.9.211

Refreshed all patches.

Compile-tested on: ar71xx
Runtime-tested on: ar71xx

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>

kirkwood: fix HDD LED labels for Zyxel NSA325 in 01_leds

Change the LED labels for hdd1/hdd2 in 01_leds to match their
counterpart in DTS.

Signed-off-by: Stephan Knauss <openwrt@stephans-server.de>
[improve commit title and message]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
(cherry picked from commit fbf297be38a93b9ca1119e5aaffecd2299087aa5)

brcm47xx: fix switch port order for Netgear WN2500RP V1

The Netgear WN2500RP V1 switch0 already works for LAN
however the port order for the LAN ports is inverted. Correct
physical port order watched from the back of the device is:
4 / 3 / 2 / 1
WAN port is absent on this device and therefore removed
from switch config.

Signed-off-by: Walter Sonius <walterav1984@gmail.com>
[move block to maintain alphabetic sorting]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
(cherry picked from commit 098cbc68ee23db589ed6f0d081fe26cc385462f2)

brcm47xx: fix switch port order for Netgear WNR3500 V2

The Netgear WNR3500 V2 switch0 already works for WAN/LAN
however the port order for the LAN ports is inverted. Correct
physical port order watched from the back of the device is:
Internet / 4 / 3 / 2 / 1 this resembles the Linksys E3000 V1.

Verfied with imagebuilder edit FILES=/etc/board.d/01_network

Signed-off-by: Walter Sonius <walterav1984@gmail.com>
(cherry picked from commit cf2f1fc6871da0320afeefaa799af87fc7c0d1db)

ramips: fix HiWiFi HC5962 switch configuration

HC5962 has only 3 LAN ports, switch port 0 is unused

Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
(backported from commit 68f49df31507454f86b72a5c1e250505176baed7)
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>

kernel: bump 4.14 to 4.14.166

Refreshed all patches.

Compile-tested on: cns3xxx
Runtime-tested on: cns3xxx

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>

kernel: bump 4.14 to 4.14.165

Refreshed all patches.

Compile-tested on: cns3xxx
Runtime-tested on: cns3xxx

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>

kernel: bump 4.9 to 4.9.210

Refreshed all patches.

Compile-tested on: ar71xx
Runtime-tested on: ar71xx

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>

kernel: bump 4.14 to 4.14.164

Refreshed all patches.

Compile-tested on: cns3xxx
Runtime-tested on: cns3xxx

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>

kernel: bump 4.9 to 4.9.209

Refreshed all patches.

Compile-tested on: ar71xx
Runtime-tested on: ar71xx

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>

ethtool: fix PKG_CONFIG_DEPENDS

Add missing CONFIG_ prefix.

Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
(cherry picked from commit 41c19dd542973dbc1336ecceaa32777506933cdf)

OpenWrt v18.06.6: revert to branch defaults

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>

OpenWrt v18.06.6: adjust config defaults

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>

ramips: remove duplicate dts nodes of MediaTek LinkIt Smart 7688

There are two identical wmac nodes in the dts file of MediaTek
LinkIt Smart 7688, so delete one of them.

Signed-off-by: Jack Chen <redchenjs@live.com>
(cherry picked from commit 4be271a4867dcf57a122eeb7b42407e7a506915e)

sunxi: Turn on CONFIG_PINCTRL_SUN4I_A10 for A20

CONFIG_PINCTRL_SUN4I_A10 controls both the A10 and the A20 enablong of
the pinctrl driver, this is necessary since upstream commit
5d8d349618a9464714c07414c5888bfd9416638f ("pinctrl: sunxi: add A20
support to A10 driver") which has been included in v4.13 and onwards.

Fixes: ad2b3bf310f7 ("sunxi: Add support for kernel 4.14")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
(cherry picked from commit 32e4eaef1b4c2a7fa44787813fdf715b2ba500d9)

kernel: bump 4.9 to 4.9.208

Refreshed all patches.

Compile-tested on: lantiq
Runtime-tested on: lantiq

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>

kernel: bump 4.14 to 4.14.162

Refreshed all patches.

Compile-tested on: ramips
Runtime-tested on: ramips

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>

ramips: fix inverted reset button for Ravpower WD03

The button events "pressed" and "released" were switched. Tested with v18.06.4.

Signed-off-by: Moritz Warning <moritzwarning@web.de>
(cherry picked from commit 3e1325b219fced91f01d5594503f61d326a93b90)

ar71xx: really fix Mikrotik board detection

commit e09da0169a08 ("ar71xx: fix Mikrotik board detection")
was generated based on testing a rb-912 board, on which detection failed.

Testing on more hardware shows something fun:

machine : MikroTik RouterBOARD 922UAGS-5HPacD
machine : Mikrotik RouterBOARD 912UAG-5HPnD

Both lowercase and uppercase are used.
So ensure we support both now ..

Fixes: e09da0169a08 ("ar71xx: fix Mikrotik board detection")
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
(cherry picked from commit 845b2a1cfe307394f3f2144cce085bbb5e171ecc)

ar71xx: fix Mikrotik board detection

Fix a typo in the machine type being extracted from /proc/cpuinfo
which causes all Mikrotik board to be undetected properly.

This lead to sysupgrade issues and probably some others too.

Fixes: acf2b6c8881b ("ar71xx: base-files: fix board detect on new MikroTik devices")
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
(cherry picked from commit e09da0169a088663f6dab1f71b2a4b690eab21d3)

ar71xx: base-files: fix board detect on new MikroTik devices

Move all MikroTik devices to new function to increase script execution
speed.

Machine name in new version of MikroTik RouterBOARD devices add "RB"
before model name:

 Old machine name: MikroTik RouterBOARD 951Ui-2nD
 New:              MikroTik RouterBOARD RB951Ui-2nD

So this patch should fix it for all currently supported MikroTik boards.

Signed-off-by: Henryk Heisig <hyniu@o2.pl>
[rebased,commit message facelift,script fixes]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
[spotted missing 922UAGS-5HPacD]
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
(cherry picked from commit acf2b6c8881b432530bd98fa86753bf6a3546ff7)
[backport: do not add boards not supported in 18.06]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>

ar71xx: fix RB941-2nD detection

Some hAP lite routers aren't detected because
/proc/cpuinfo shows "RouterBOARD RB941-2nD"
instead of "RouterBOARD 941-2nD".

Fix that.

Signed-off-by: Julien Rabier <taziden@flexiden.org>
[Alter string to include all flavours + slight rewrite of commit msg]
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
(cherry picked from commit 6570f3c93aa4110efd1466a6b89742c2e11d7c11)

kernel: bump 4.14 to 4.14.161

Refreshed all patches.

Compile-tested on: ipq40xx
Runtime-tested on: none

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>

e2fsprogs: Fix CVE-2019-5094 in libsupport

This adds the following patch from debian:
https://git.kernel.org/pub/scm/fs/ext2/e2fsprogs.git/commit/?h=debian/stable&id=09fe1fd2a1f9efc3091b4fc61f1876d0785956a8
libsupport: add checks to prevent buffer overrun bugs in quota code

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit 0062aad8ecc9bbe36c55895fd78fcaf9a406b006)

openssl: update to version 1.0.2u

Fixes CVE-2019-1551 (rsaz_512_sqr overflow bug) on x86_x64

Signed-off-by: Josef Schlehofer <pepe.schlehofer@gmail.com>

kernel: bump 4.9 to 4.9.207

Refreshed all patches.

Compile-tested on: lantiq
Runtime-tested on: none

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>

kernel: bump 4.14 to 4.14.160

Refreshed all patches.

Compile-tested on: ipq40xx
Runtime-tested on: none

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>

kernel: bump 4.14 to 4.14.159

Refreshed all patches.

Fixes:
- CVE-2019-19332

Compile-tested on: cns3xxx
Runtime-tested on: cns3xxx

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>

scripts/dowload.pl: add archive.apache.org to apache mirror list

apache mirrors holds only latest releases, to download
older releases, one must use archive.apache.org to get
them.

Signed-off-by: Jiri Kastner <cz172638@gmail.com>
(cherry picked from commit dc34c695c4faa46efc6e2367a2ba06a47caa4840)

kernel: fix *-gpio-custom module unloading

Unloading and reloading the modules fails, as platform_device_put() does not
release resources fully.

root@OpenWrt:/# insmod i2c-gpio-custom bus0=0,18,0,5
[  196.860620] Custom GPIO-based I2C driver version 0.1.1
[  196.871162] ------------[ cut here ]------------
[  196.880517] WARNING: CPU: 0 PID: 1365 at fs/sysfs/dir.c:31 0x80112158
[  196.893431] sysfs: cannot create duplicate filename '/devices/platform/i2c-gpio.0'
...
[  197.513200] kobject_add_internal failed for i2c-gpio.0 with -EEXIST, don't try to register things with the same name in the same directory.

This patch fixes it by replacing platform_device_put() to
platform_device_unregister().

Fixes: da7740853715 ("i2c-gpio-custom: minor bugfix")
Fixes: 3bc81edc70e8 ("package: fix w1-gpio-custom package (closes #6770)")
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
(cherry picked from commit a22b7a60d98836343c4f7b9ec0fcae68d9131522)

toolchain/gcc: correct the check expr for newer clang

This fixes gcc build error within clang 11.0, it tweaks the version
string from LLVM to clang.

Signed-off-by: Yorkie Liu <yorkiefixer@gmail.com>
(cherry picked from commit 65a561fd0919eafff2363ae8324db64be2a57f77)

lantiq: fix phys led

led2l and led2h value is incorrectly set by led3l and led3h.
Bug was introduced in commit: 863e79f8d5544a8a884375d7e867f350fddca9b9

Signed-off-by: Aleksander Jan Bajkowski <A.Bajkowski@stud.elka.pw.edu.pl>
Fixes: 863e79f8d554 ("lantiq: add support for kernel 4.9")
(cherry picked from commit 692390225d76de8f2daf582454e74942b82d090a)

uhttpd: update to latest Git HEAD

5f9ae57 client: fix invalid data access through invalid content-length values
6b03f96 ubus: increase maximum ubus request size to 64KB
91fcac3 uhttpd: Fix multiple format string problems

Signed-off-by: Jo-Philipp Wich <jo@mein.io>
(backported from commit f34f9a414dd32311bda950776eb77e63c0c772cb)

netifd: add support for suppressing the DHCP request hostname by setting it to *

dnsmasq (and probably other DHCP servers as well) does not like to hand out
leases with duplicate host names.
Adding support for skipping the hostname makes it easier to deploy setups
where it is not guaranteed to be unique

Signed-off-by: Felix Fietkau <nbd@nbd.name>
(cherry picked from commit fd8ca8deb3197a2867d85fc3513f5aa70912ee40)

ar71xx: fix MAC address setup for TL-WDR4300 board

The current ethernet MAC address setup of TL-WDR4300 board is different
from the setup of stock firmware:

OpenWrt: lan = label_mac -2, wan = label_mac -2
  stock: lan = label_mac,    wan = label_mac +1

This patch applies to all devices using TL-WDR4300 board:
TL-WDR3600 v1
TL-WDR4300 v1
TL-WDR4300 v1 (IL)
TL-WDR4310 v1
Mercury MW4530R v1

Signed-off-by: Sungbo Eo <mans0n@gorani.run>
(cherry picked from commit 9b02d32e34df2bb8821ec6f08f525bee22d0d1ba)

ramips: fix number of LAN Ports for Mikrotik RBM33G

The Mikrotik RBM33G has only 2 LAN ports.

Signed-off-by: Martin Schiller <ms@dev.tdt.de>
[moved node in 02_network to maintain alphabetic sorting; backport]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
(cherry picked from commit 3a55c7935d4efdc86575601cb4aa7bc94e3c5e44)

ramips: fix switch port order for TP-Link Archer C20i

Physical port order watched from the backside of the C20i
(from left to right) is: Internet / 1 / 2 / 3 / 4

Physical Port Switch port
WAN             0
LAN 3           1
LAN 4           2
LAN 1           3
LAN 2           4
(not used)      5
CPU             6

Signed-off-by: Walter Sonius <walterav1984@gmail.com>
[commit message/title improvements; backport to 18.06]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
(cherry picked from commit a065cd29bf2dfd1ce1f07becd65aef96cec658e7)

kernel: bump 4.14 to 4.14.158

Refreshed all patches.

Altered patches:
- 400-mtd-add-rootfs-split-support.patch

Compile-tested on: cns3xxx
Runtime-tested on: cns3xxx

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>

kernel: bump 4.9 to 4.9.206

Refreshed all patches.

Altered patches:
- 400-mtd-add-rootfs-split-support.patch

Compile-tested on: ar71xx
Runtime-tested on: ar71xx

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>

mac80211: Adapt to changes to skb_get_hash_perturb()

The skb_get_hash_perturb() function now takes a siphash_key_t instead of
an u32. This was changed in commit 55667441c84f ("net/flow_dissector:
switch to siphash"). Use the correct type in the fq header file
depending on the kernel version.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>
(cherry picked from commit eaa047179ad30d156d0c3da7ec225acfae7a9f00)

kernel: bump 4.9 to 4.9.205

Refreshed all patches.

Altered patches:
- 402-mtd-support-layerscape.patch

Fixes:
- CVE-2019-18660

Compile-tested on: ar71xx
Runtime-tested on: ar71xx

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>

kernel: bump 4.14 to 4.14.156

Refreshed all patches.

Compile-tested on: cns3xxx
Runtime-tested on: cns3xxx

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>

base-files: config_generate: split macaddr with multiple ifaces

netifd does not handle network.@device[x].name properly if it
contains multiple ifaces separated by spaces. Due to this, board.d
lan_mac setup does not work if multiple ifaces are set to LAN by
ucidef_set_interface_lan.

To fix this, create a device node for each member iface when
running config_generate instead. Those are named based on the
member ifname:

  ucidef_set_interface_lan "eth0 eth1.1"
  ucidef_set_interface_macaddr "lan" "yy:yy:yy:yy:yy:01"

will return

  config device 'lan_eth0_dev'
        option name 'eth0'
        option macaddr 'yy:yy:yy:yy:yy:01'

  config device 'lan_eth1_1_dev'
        option name 'eth1.1'
        option macaddr 'yy:yy:yy:yy:yy:01'

ref: https://github.com/openwrt/openwrt/pull/2542

Signed-off-by: Sungbo Eo <mans0n@gorani.run>
[always use new scheme, extend description, change commit title]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
(cherry picked from commit 298814e6be7640d89328de9e7c90d4349e30683f)

kernel: nf_conntrack_rtcache: fix WARNING on rmmod

Fixes b7c58a1ee ("kernel: nf_conntrack_rtcache: fix cleanup on netns
delete and rmmod")

Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
(cherry picked from commit b3779e920ebaa168eaf18ac1140774c32b6ec6b6)

kernel: nf_conntrack_rtcache: fix WARNING on forward path

Fixes b7c58a1ee ("kernel: nf_conntrack_rtcache: fix cleanup on netns
delete and rmmod")

Resolves FS#2624

Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
(cherry picked from commit 1c5df850a07690451f2878a310c0ea67d0690836)

kernel: nf_conntrack_rtcache: fix cleanup on netns delete and rmmod

Fixes FS#1472, FS#2353, FS#2426

Fixes: b3f95490 ("kernel: generic: Add kernel 4.14 support")
Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
Acked-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit b7c58a1eeba5be2e1f77ec05b417be9d87e26916)

kernel: Add missing configuration option

This was found by the build bot.

Fixes: 6e2e5d1bf8d5 ("kernel: bump 4.14 to 4.14.155")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit 103e49f62e72664ee0d5285007907a75960e8645)

kernel: bump 4.14 to 4.14.155

Refreshed all patches.

Altered patches:
- 707-dpaa-ethernet-support-layerscape.patch
- 421-rtc-initialize.patch

Remove upstreamed:
- 161-MIPS-BCM47XX-Enable-USB-power-on-Netgear-WNDR3400v3.patch

Compile-tested on: cns3xxx
Runtime-tested on: cns3xxx

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>

ar71xx: fix buttons for TP-Link TL-WDR4900 v2

TP-Link TL-WDR4900 v2 only has one combined WPS/Reset button, so
don't set up an RFKILL for this device.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
(cherry picked from commit 25127f58b42d794bd47d56ea107f3dfc9cc4816c)

ar71xx: fix LED setup for TL-WDR4900 v2

In ar71xx there is only one combined mach file for Archer C5/C7 and
TL-WDR4900 v2. This one uses the same LED struct for all devices,
defining "green" LEDs for them. However, WDR4900 uses blue front
LEDs, while only C5/C7 uses green ones. Despite, in base-files
WDR4900 is actually set up with "blue" for the mentioned LEDs.

Thus, this patch creates a separate LED struct for WDR4900, so the
LEDs can be set up correctly. Despite, the wlan5g LED is removed as
it is controlled by ath9k chip for WDR4900 (in contrast to C5/C7).

Note: While front LEDs are blue, USB LEDs (on the back) are green,
so colors are mixed intentionally for the WDR4900 v2.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
(cherry picked from commit 93f2bcc35e371ec0c4ceb76c06f90b898c726ba5)

ramips: set uImage name of WeVO 11AC NAS and W2914NS v2

The stock firmware and bootloader only accept uImage with names that
match certain patterns. This patch enables OpenWrt installation from
stock firmware without having to reflash the bootloader or access the
UART console.

Installation via web interface:
1.  Flash **initramfs** image through the stock web interface.
2.  Boot into OpenWrt and perform sysupgrade with sysupgrade image.

Signed-off-by: Sungbo Eo <mans0n@gorani.run>
(cherry picked from commit 19800ac095f6ddbba03ccab08e5197b1eec4a49e)
[backported]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>

ar71xx: fix MAC address setup for TL-WDR4900 v2

The MAC address setup of the TL-WDR4900 v2 is different from the
C5/C7. This aligns ar71xx with the setup in ath79:

wlan0 (5GHz) : -2
wlan1 (2.4GHz) : -1
eth1 (LAN) : 0
eth0 (WAN) : 1

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
(cherry picked from commit a9d3084b83bb2d0fa2c0b43bf2a0831b5ae1df13)

ar71xx: fix MAC addresses for Archer C5 v1, C7 v1/v2, WDR4900 v2

As discussed in 1d18a14a90c7 ("ath79: really fix TP-Link Archer C7
v2 MAC address"), stock firmware MAC address assignment is
actually as follows:

wlan0 (5GHz) : -1
wlan1 (2.4GHz) : 0
eth1 (LAN) : 0
eth0 (WAN) : 1

This has never been fixed for ar71xx, so let's do it now.
Note that with WDR4900 v2 even both wlan0 and wlan1 where assigned
to basemac-1 before ...

Fixes: FS#408
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
(cherry picked from commit a021268032fb64afdce7bafa91c7c7bf44fa6ff2)

ipq40xx: fix build error

Add missing brace which was accidentally omitted

Fixes: 6d6026021390 ("kernel: bump 4.14 to 4.14.154")
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>

kernel: bump 4.14 to 4.14.154

Refreshed all patches.

Altered patches:
- 902-debloat_proc.patch
- 040-dmaengine-qcom-bam-Process-multiple-pending-descript.patch

Remove upstreamed:
- 303-spi-nor-enable-4B-opcodes-for-mx66l51235l.patch

New symbols:
X86_INTEL_MPX
X86_INTEL_MEMORY_PROTECTION_KEYS
X86_INTEL_TSX_MODE_OFF
X86_INTEL_TSX_MODE_ON
X86_INTEL_TSX_MODE_AUTO
SGL_ALLOC

Compile-tested on: cns3xxx
Runtime-tested on: cns3xxx

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>

kernel: bump 4.9 to 4.9.202

Refreshed all patches.

Altered patches:
- 902-debloat_proc.patch
- 817-usb-support-layerscape.patch

New symbols:
X86_INTEL_MEMORY_PROTECTION_KEYS
X86_INTEL_TSX_MODE_OFF
X86_INTEL_TSX_MODE_ON
X86_INTEL_TSX_MODE_AUTO

Compile-tested on: ar71xx
Runtime-tested on: ar71xx

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>

ar71xx: fix WLAN LED names for Archer C7

Update WLAN LED colour identifier for both interfaces on Archer C7

Signed-off-by: Tomislav Požega <pozega.tomislav@gmail.com>
(cherry picked from commit 65762cdd2223d759f5836214143888e32ce5766b)
[backported to 18.06]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>

ar71xx: fix system LED names on Archer C5/C7

Move system LED board definitions of Archer C5/C7 to reflect
actual system LED colour used

Signed-off-by: Tomislav Požega <pozega.tomislav@gmail.com>
(cherry picked from commit a73934fc9ad05207e79a3e58abc3d14eee28b6f2)

mac80211: brcmfmac: fix PCIe reset crash and WARNING

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
(cherry picked from commit cde8c2f2fba019c4cd3b9f6ad463ff86cc783061)

ramips: assign correct key-code to wps buttons

The two ASUS WL-330N and WL-330N3G had the reset keycode
assigned to the WPS button. This patch changes both devices
to use KEY_WPS_BUTTON in the hopes that this fixes unwanted
restarts/ unexpected behavior from the users point of view.

[dropped RG21S]
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
(cherry picked from commit ad65d9d7b264d6d17293c59469e770905d2f785a)

ramips: rt3833: fix build breakage

Commit 60f41c6c9ef6 ("ramips: add usb-ledtrig-usbport to DEVICE_PACKAGES
of CY-SWR1100") added stray | during backport which caused build
breakage on the buildbots:

 bash: -c: line 0: syntax error near unexpected token `|'
 bash: -c: line 0: `echo kmod-usb-core kmod-usb-ledtrig-usbport kmod-usb-ohci kmod-usb2 swconfig | | mkhash md5 | head -c 8'

Fixes: 60f41c6c9ef6 ("ramips: add usb-ledtrig-usbport to DEVICE_PACKAGES of CY-SWR1100")
Signed-off-by: Petr Štetiar <ynezz@true.cz>
(cherry picked from commit a1ff175dbf807925a0bae537935455bd1aa44a98)

ramips: add usb-ledtrig-usbport to DEVICE_PACKAGES of CY-SWR1100

CY-SWR1100 has a USB LED but kmod-usb-ledtrig-usbport is missing
in default images. This commit adds it.

Signed-off-by: Sungbo Eo <mans0n@gorani.run>
[changed commit title, backported to 19.07]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
(cherry picked from commit 261c746631d2bf311a6b62a6d3bacce6fde90976)

ramips: fix MAC address setup for Samsung CY-SWR1100

Ethernet MAC address setup has been broken since c3e420f28cf1. Restore
original setting.

Fixes: c3e420f28cf1 ("ramips: Add support for D-Link DCH-M225")
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
(cherry picked from commit 7231c1edd99217c6baa8d7d5d841d75ad9de26f1)
[backported due to base-files split]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>

gitignore: ignore patches in OpenWrt root directory

This will have GIT ignore patches in root directory, as created
when using "git format-patch".

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
(cherry picked from commit 2c5413559880c54c5eec980121febfe6c7cd287a)

ar71xx: fix tl-wdr3320-v2 upgrade

Fix the error that tl-wdr3320-v2 can't upgrade firmware via web
interface by using magic_ver="0200" for this device.

Signed-off-by: 南浦月 <nanpuyue@gmail.com>
[commit message facelift]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
(cherry picked from commit 0ff2385a92c0a31769fce954b7bd571d6114dbc8)

ar71xx: update uboot-envtools for Netgear WNR routers

Boards added: WNR1000v2, WNR2000v3, WNR2200, WNR612v2, WNDR4300.
Boards changed: WNDR3700 (u-boot env size is 2 sectors not 1).

Signed-off-by: Michal Cieslakiewicz <michal.cieslakiewicz@wp.pl>
(cherry picked from commit 11052900494ec8216b9b39ba0b24d5e036f4d323)

kernel: bump 4.14 to 4.14.152

Refreshed all patches.

Compile-tested on: cns3xxx
Runtime-tested on: cns3xxx

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>

kernel: bump 4.9 to 4.9.199

Refreshed all patches.

Compile-tested on: ar71xx
Runtime-tested on: ar71xx

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>

sdk: fix GCC and Python dangling symlinks

Force prereq again in SDK in order to fix GCC and Python dangling
symlinks:

 staging_dir/host/bin/g++ -> /builder/ath79_generic/ccache_cxx.sh
 staging_dir/host/bin/gcc -> /builder/ath79_generic/ccache_cc.sh
 staging_dir/host/bin/python -> /usr/bin/python3.5
 staging_dir/host/bin/python3 -> /usr/bin/python3.5

Ref: FS#2424
Signed-off-by: Petr Štetiar <ynezz@true.cz>
(cherry picked from commit 200f2666fb1c8d9d128824dc5586e0e66386971f)

build: cleanup possibly dangling Python 3 host symlink

When switching from master branch to 19.07 or older, we need to ensure
that Python symlink in staging bin directory points to Python 2.

We can't rely completly just on SetupHostCommand as its executed only in
cases when the $(STAGING_DIR_HOST)/bin/python doesn't already exist, so
we need to remove it before running SetupHostCommand.

This is a cherry-pick of 3b68fb57c938af3948ae4c2da61501183fbef649
with python3 instead of python2

Signed-off-by: Petr Štetiar <ynezz@true.cz>
Signed-off-by: Etienne Champetier <champetier.etienne@gmail.com>
(cherry picked from commit 799de7c641ffa98323929a20a8d92c7cc4ebb251)

build: fixup python SetupHostCommand to use python2

Here is a way to break your build env without this patch:
1) have python point to python3, and no python2
2) start the build, SetupHostCommand will create a symlink
./staging_dir/host/bin/python -> /usr/bin/python
3) build fails on scons because it can't find any python2
4) install python2 and restart the build
5) the build fails on wireless-regdb compile because python is python3 instead of python

Signed-off-by: Etienne Champetier <champetier.etienne@gmail.com>
(cherry picked from commit 785d4f3efded4a5094ee8e1ce4535dd0933b956d)

OpenWrt v18.06.5: revert to branch defaults

Signed-off-by: Jo-Philipp Wich <jo@mein.io>