Aleksander Jan Bajkowski [Sat, 12 Dec 2020 15:28:39 +0000 (16:28 +0100)]
lantiq: xrx200: remove unused lan/wan labels from dts
These labels are not used anywhere and can be removed.
Signed-off-by: Aleksander Jan Bajkowski <A.Bajkowski@stud.elka.pw.edu.pl>
Martin Blumenstingl [Sat, 28 Nov 2020 11:08:42 +0000 (12:08 +0100)]
ath79: add support for the Belkin F9K1115 v2 (AC1750 DB Wi-Fi)
This device has (almost?) identical hardware to the F9J1108 v2 but uses
a different firmware magic and model number.
Specifications:
SoC: QCA9558
CPU: 720 MHz
Flash: 16 MiB NOR
RAM: 128 MiB
WiFi 2.4 GHz: QCA9558-AT4A 3x3 MIMO 802.11b/g/n
WiFi 5 GHz: QCA9880-2R4E 3x3 MIMO 802.11a/n/ac
Ethernet: 4x LAN and 1x WAN (all 1Gbit/s ports)
USB: 1 x USB 2.0 (lower), 1 x USB 3.0 (upper)
MAC addresses based on OEM firmware:
Interface Address Location
--------- ------- --------
lan *:5A sometimes in 0x6
wan *:5B 0x0
2.4Ghz *:5A 0x1002
5Ghz As per mini PCIe EEPROM
Flashing instructions:
The factory.bin can be flashed via the Belkin web UI or via the uboot
HTTP upgrade page (which is by default listening on 192.168.2.1). Once
the factory.bin has been written, sysupgrade.bin will work as usual.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Martin Blumenstingl [Sat, 28 Nov 2020 11:04:00 +0000 (12:04 +0100)]
ath79: create shared DTSI/definition for Belkin F9J1108/F9K1115 v2
Belkin F9J1108 v2 and F9K1115 v2 are (seemingly) identical hardware
with different model numbers. Extract all non-device specific code to a
common .dtsi so it can be re-used when adding support for the
F9K1115 v2.
Similar to the .dtsi most of the image building recipe code can be
re-used. Move everything except the device model, edimax header magic
and edimax header model into a shared build recipe.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
[drop duplicate TARGET_DEVICES, add EDIMAX_* to DEVICE_VARS, edit title]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Gioacchino Mazzurco [Mon, 14 Dec 2020 09:48:43 +0000 (10:48 +0100)]
tplink-safeloader: add support for TP-Link CPE510 v3.20
This adds new strings for the v3.20 to the support list of the
already supported TP-Link CPE510 v3.
The underlying hardware appears to be the same, similar to the
situation with CPE210 v3.20 in
4a2380a1e778 ("tplink-safeloader:
expand support list for TP-Link CPE210 v3")
Signed-off-by: Gioacchino Mazzurco <gio@altermundi.net>
[extended commit message]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Petr Štetiar [Thu, 10 Dec 2020 14:31:26 +0000 (15:31 +0100)]
uclient: update to Git version 2020-12-10
2c843b2bc04c Add initial GitLab CI support
073f89f567c0 uclient-fetch: wolfSSL: fix certificate validation
086c292160ac uclient-fetch: init_ca_cert: fix memory leak
a3c1a88b031a cmake: enable extra compiler checks
32ff717ed316 uclient-http: fix extra compiler warnings on mips_24kc and cortex-a9+neon
86a2ac6ac46f uclient-fetch: fix potential memory leaks
158dd9dd289c uclient: fix initialized but never read variable
66b4420856a7 uclient-fetch: fix statement may fallt hrough
436f9b3af2ad uclient-http: fix freeing of stack allocated memory
e6b5b8a98ce2 Fix extra compiler warnings
12df67e45bb0 Add basic cram based unit tests
b6e34845124f cmake: fix building out of the tree
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Petr Štetiar [Thu, 10 Dec 2020 14:29:12 +0000 (15:29 +0100)]
ustream-ssl: update to Git version 2020-12-10
68d09243b6fd Add initial GitLab CI support
8280140db9d1 wolfssl: remove now deprecated compatibility code
cee6791b362a ustream-mbedtls: fix certificate verification
55c3fd89d508 ustream-mbedtls: implement set_require_validation
c6b4c48689a3 ustream-openssl: wolfSSL: fix certificate validation
3bc05402bfab cmake: enable extra compiler checks
cd2c3d12db43 ustream-mbedtls: fix comparison of integers of different signs
5896991e46a3 ustream-openssl: fix BIO_method memory leak
2c342ae57c5b ustream-openssl: fix wolfSSL includes
fa8ecd6ed140 cmake: fix linking when mbed TLS not in default paths
63656f81045f cmake: fix linking when wolfSSL not in default paths
c26f71e844df cmake: fix building out of the tree
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Paul Spooren [Mon, 14 Dec 2020 00:36:17 +0000 (14:36 -1000)]
build/json: add filesystem information
Some images are created using different filesystems, most popular
squashfs and ext4. To allow downstream projects to distinguesh between
those, add the `filesystem` information to created json files.
Signed-off-by: Paul Spooren <mail@aparcar.org>
David Bauer [Tue, 1 Dec 2020 17:55:27 +0000 (18:55 +0100)]
ipq40xx: revert usage of VLAN S-TAG
This reverts the usage of the S-Tag for separating LAN and WAN port on
the embedded switch. Many users complained about not being able to
manage C-Tag addition / removal on the switch as well as degraded
performance.
Fixes: commit 9da2b567605b ("ipq40xx: fix ethernet vlan double tagging")
Signed-off-by: David Bauer <mail@david-bauer.net>
Rui Salvaterra [Mon, 19 Oct 2020 18:21:13 +0000 (19:21 +0100)]
zram-swap: remove the compression streams settings
Zram switched to per-cpu compression streams since Linux 4.7 [1]. Drop the
irrelevant configuration (no-op).
[1] https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/commit/drivers/block/zram?h=v4.7&id=
43209ea2d17aae1540d4e28274e36404f72702f2
Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
Christian Lamparter [Sun, 13 Dec 2020 15:14:35 +0000 (16:14 +0100)]
bcm53xx: MR32: fix DEVICE_VENODR typo
DEVICE_VENDOR was misspelled as DEVICE_VENODR.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Yushi Nishida [Fri, 27 Nov 2020 20:54:22 +0000 (21:54 +0100)]
ipq40xx: fix 5Ghz tx/rx power on the ASUS MAP-AC2200
The ASUS MAP-AC2200 suffers from a lower transmit/receive
signal power as compared to the stock firmware.
Upon investigation, it was discovered that stock firmware from
the GPL_MAP-AC2200_3
.0.0.4.384.46249-g97d05bb.tar archive.
set the following GPIOs in "release/src/router/rc/init.c".
GPIO 44 and 46 have to be set to output high
GPIO 45 and 47 have to be set to output low
Here are some results, after activating the relevant
gpios through cmdline:
<https://forum.openwrt.org/t/asus-map-ac2200-low-transmit-receive-signal-5ghz/69005/12>
THX @ slh
Fixes: 9ad3967f140 ("ipq40xx: add support for ASUS Lyra")
Signed-off-by: Yushi Nishida <kyro2man@gmx.net>
[slightly rewritten commit, added missing <>)
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Luis Araneda [Sun, 2 Aug 2020 23:34:42 +0000 (19:34 -0400)]
uboot-zynq: fix dtc compilation on host gcc 10
gcc 10 defaults to -fno-common, which causes an error
when linking.
Back-port the following Linux kernel commit to fix it:
e33a814e772c (scripts/dtc: Remove redundant YYLOC global declaration)
Tested on an Arch Linux host with gcc 10.1.0
Signed-off-by: Luis Araneda <luaraneda@gmail.com>
Daniel Golle [Sun, 13 Dec 2020 00:12:37 +0000 (00:12 +0000)]
odhcpd: remove local mkdir_p implementation
Replace local mkdir_p implementation in favour of using mkdir_p now
added to libubox.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Daniel Golle [Sat, 12 Dec 2020 23:33:14 +0000 (23:33 +0000)]
procd: update to git HEAD
111416d jail: remove unreachable code
7f12c89 treewide: replace local mkdir_p implementations
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Daniel Golle [Sat, 12 Dec 2020 23:29:59 +0000 (23:29 +0000)]
fstools: update to git HEAD
0c6fb90 jffs2-reset: allow doing a factory reset and passing a sysupgrade.tgz
4862530 mount: restorecon: guard against execl() errors
f415323 block: replace local mkdir_p implementation
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Daniel Golle [Sat, 12 Dec 2020 23:26:16 +0000 (23:26 +0000)]
libubox: utils: introduce mkdir_p
Add new utility function mkdir_p(char *path, mode_t mode) to replace
the partially buggy implementations found accross fstools and procd.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Daniel Golle [Sat, 12 Dec 2020 14:45:16 +0000 (14:45 +0000)]
selinux-policy: update to version 0.4
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Philip Prindeville [Mon, 7 Dec 2020 20:19:30 +0000 (13:19 -0700)]
xfrm: support 'multicast' attribute on interfaces
You shouldn't need the overhead of GRE just to add multicast
capability on a point-to-point interface (for instance, you might
want to run mDNS over IPsec transport connections, and Avahi
requires IFF_MULTICAST be set on interfaces, even point-to-point
ones).
Borrowed heavily from:
b3c9321b9e gre: Support multicast configurable gre interfaces
Signed-off-by: Philip Prindeville <philipp@redfish-solutions.com>
Eneas U de Queiroz [Fri, 11 Dec 2020 11:39:35 +0000 (08:39 -0300)]
openssl: update to 1.1.1i
Fixes: CVE-2020-1971, defined as high severity, summarized as:
NULL pointer deref in GENERAL_NAME_cmp function can lead to a DOS
attack.
Signed-off-by: Eneas U de Queiroz <cotequeiroz@gmail.com>
Marty Jones [Tue, 24 Nov 2020 02:49:10 +0000 (21:49 -0500)]
kernel: add Aquantia AQtion USB-to-5GbE adapters
This add support for USB-to-Ethernet Aquantia AQtion
5/2.5GbE adapters based on the AQC111U controllers.
Run-tested: x86
Adapter-tested: Sabrent NT-SS5G
Signed-off-by: Marty Jones <mj8263788@gmail.com>
Karel Kočí [Thu, 22 Oct 2020 11:29:57 +0000 (13:29 +0200)]
mvebu: fix initramfs/kernel image for CZNIC Turris Omnia
This adds DTB to kernel and that way makes it possible to easily boot
initramfs image and also kernel.
The sequence to boot initramfs on Omnia is then just:
env set bootargs earlyprintk console=ttyS0,115200
dhcp 0x1000000 192.168.1.1:openwrt-mvebu-cortexa9-cznic_turris-omnia-initramfs-kernel.bin
bootz 0x1000000
Without this change kernel boot won't proceed and is stuck on "Starting
kernel".
Signed-off-by: Karel Kočí <karel.koci@nic.cz>
[fixed From: to match with SoB:]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Konstantin Demin [Wed, 25 Nov 2020 03:16:06 +0000 (06:16 +0300)]
dropbear: bump package version
Bump package version after previous changes.
Signed-off-by: Konstantin Demin <rockdrilla@gmail.com>
[added missing commit description]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Konstantin Demin [Wed, 25 Nov 2020 03:14:30 +0000 (06:14 +0300)]
dropbear: add ssh-askpass support in configuration
binary size cost is much less than 1k.
tested on ath79/generic:
bin: 215128 -> 215132 (+4b)
ipk: 111183 -> 111494 (+311b)
Signed-off-by: Konstantin Demin <rockdrilla@gmail.com>
Konstantin Demin [Wed, 25 Nov 2020 03:12:41 +0000 (06:12 +0300)]
dropbear: roll up recipes into mapping lists
this commit removes manual recipes for options and introduces mapping lists:
- DB_OPT_COMMON holds option mappings which are common for all builds;
- DB_OPT_CONFIG holds option mappings which are depend on config settings.
DB_OPT_COMMON is space-separated list of 'words', each of them is in format:
'header_option|value'
'header_option' is added with value 'value' to 'localoptions.h'.
if 'header_option' is preceded by two exclamation marks ('!!')
then option is not added to 'localoptions.h' but replaced in 'sysoptions.h'.
in short:
option|value - add option to localoptions.h
!!option|value - replace option in sysoptions.h
DB_OPT_CONFIG is space-separated list of 'words', each of them is in format:
'header_option|config_variable|value_enabled|value_disabled'
'header_option' is handled likewise in DB_OPT_COMMON.
if 'config_variable' is enabled (technically: not disabled)
then 'header_option' is set to 'value_enabled' and 'value_disabled' otherwise.
in short:
option|config|enabled|disabled = add option to localoptions.h
!!option|config|enabled|disabled = replace option in sysoptions.h
option := (config) ? enabled : disabled
If you're not sure that option's value doesn't have '|' within - add your recipe
manually right after '$(Build/Configure/dropbear_headers)' and write some words
about your decision.
PS about two exclamation marks:
early idea was to use one exclamation mark to denote such header options
but then i thought single exclamation mark may be overlooked by mistake.
Signed-off-by: Konstantin Demin <rockdrilla@gmail.com>
Konstantin Demin [Wed, 25 Nov 2020 04:33:25 +0000 (07:33 +0300)]
dropbear: rework recipes that configure build
- add two helper functions to avoid mistakes with
choice of correct header file to work with
- update rules accordingly
Signed-off-by: Konstantin Demin <rockdrilla@gmail.com>
Konstantin Demin [Tue, 24 Nov 2020 23:59:59 +0000 (02:59 +0300)]
dropbear: reorder options in Configure recipe
put static options at first place, then place configurable options.
also put DROPBEAR_ECC right before DROPBEAR_ECC_FULL to ease maintainance.
Signed-off-by: Konstantin Demin <rockdrilla@gmail.com>
Konstantin Demin [Tue, 24 Nov 2020 22:54:05 +0000 (01:54 +0300)]
dropbear: enable back DROPBEAR_USE_PASSWORD_ENV
this option was disabled in 2011 and these long nine years showed us that change was definitely wrong.
binary size cost is much less than 1k.
tested on ath79/generic:
bin: 215128 -> 215128 (no change)
ipk: 111108 -> 111183 (+75b)
Fixes: 3c801b3dc0359 ("tune some more options by default to decrease size")
Signed-off-by: Konstantin Demin <rockdrilla@gmail.com>
Rafał Mikrut [Tue, 8 Dec 2020 21:01:14 +0000 (22:01 +0100)]
realtek: Add missing case in switch statement
Cppcheck shows here duplicated break.
Code `state->speed = SPEED_1000;` will be never executed because above
it there is break statement.
Almost identical statement is placed in another realtek driver
https://github.com/openwrt/openwrt/blob/
18a53d43d646290053eff4736ec852efcf6bf510/target/linux/realtek/files-5.4/drivers/net/dsa/rtl83xx/dsa.c#L286-L294
Signed-off-by: Rafał Mikrut <mikrutrafal@protonmail.com>
Rafał Mikrut [Tue, 8 Dec 2020 20:54:40 +0000 (21:54 +0100)]
realtek: Fix self assignment
Cppcheck shows self initialization error, which is an obvious bug.
Basing on logic of similar fragment below I assigned to this variable,
value `RTL838X_LED_GLB_CTRL` which I think is proper.
Signed-off-by: Rafał Mikrut <mikrutrafal@protonmail.com>
John Thomson [Wed, 9 Dec 2020 03:03:04 +0000 (13:03 +1000)]
package/base-files: caldata: use dd iflag fullblock
This dd flag ensures that the requested size
is retrieved from pipes or special filesystems (if available).
Without this flag, on multi-core systems,
Piped or special filesystem data can be truncated
when a size greater than PIPE_BUF is requested.
Fixes: FS#3494
Fixes: 7557e7f ("package/base-files: caldata: work around dd's
limitation")
Cc: Thibaut VARÈNE <hacks@slashdirt.org>
Signed-off-by: John Thomson <git@johnthomson.fastmail.com.au>
Petr Štetiar [Mon, 7 Dec 2020 09:10:49 +0000 (10:10 +0100)]
wolfssl: fix broken wolfSSL_X509_check_host
Backport upstream post 4.5.0 fix for broken wolfSSL_X509_check_host().
References: https://github.com/wolfSSL/wolfssl/issues/3329
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Eneas U de Queiroz [Mon, 7 Dec 2020 02:43:48 +0000 (23:43 -0300)]
wolfssl: compile with --enable-opensslall
This enables all OpenSSL API available. It is required to avoid some
silent failures, such as when performing client certificate validation.
Package size increases from 356.6K to 374.7K for
arm_cortex-a9_vfpv3-d16.
Signed-off-by: Eneas U de Queiroz <cotequeiroz@gmail.com>
Eneas U de Queiroz [Mon, 7 Dec 2020 02:43:47 +0000 (23:43 -0300)]
wolfssl: add lighty support, skip crypttests
Tnis adds the --enable-lighty option to configure, enabling the minimum
API needed to run lighttpd, in the packages feed. Size increase is
about 120 bytes for arm_cortex-a9_vfpv3-d16.
While at it, speed up build by disabling crypt bench/test.
Signed-off-by: Eneas U de Queiroz <cotequeiroz@gmail.com>
Daniel González Cabanelas [Thu, 10 Dec 2020 09:26:46 +0000 (10:26 +0100)]
bcm63xx: DGND3700v1: use the real board name
The Netgear DGND3700v1/DGND3800B shows kernel redundant info at the board
message, already provided by the machine info message.
Use the real board name which is silkscreened on the PCB and used in the
stock firmware header.
Signed-off-by: Daniel González Cabanelas <dgcbueu@gmail.com>
Daniel Golle [Thu, 10 Dec 2020 19:29:03 +0000 (19:29 +0000)]
config: add big EXPERIMENTAL option
As discussed in the today's (2020-12-10) meeting, add a new option to
menuconfig to group the selection of all experimental features to be
selected by default.
Developers are recommended to make use of this new symbol to guard
new features.
Other developers and community members should feel encouraged to
build with this flag enabled to help testing and provide feedback.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Karel Kočí [Tue, 10 Dec 2019 12:04:19 +0000 (13:04 +0100)]
scripts/feeds: fix preference of package install
The previous behavior prefered same feed for dependent packages as
initial package. This caused inconsitency in installation of packages.
The difference was if two feeds provide same package (different version)
there was different result if you executed install for that specific
version compared to install for package depending on it from different
feed.
This ensures that preferred feed is propagated without change and
selected feed is used only really for package it was selected for.
Signed-off-by: Karel Kočí <karel.koci@nic.cz>
Paul Spooren [Sun, 6 Dec 2020 19:24:52 +0000 (09:24 -1000)]
opkg: remove legacy dist and extra_data
efb26a3 libopkg: remove "extra_data" option
1d67ab7 libopkg: remove support for "dist" config
Reduces opkg size by about 400 Bytes.
Signed-off-by: Paul Spooren <mail@aparcar.org>
Paul Spooren [Wed, 9 Dec 2020 21:20:49 +0000 (11:20 -1000)]
iftop: remove package
The package has no reason to be in openwrt.git. Move it to packages.git.
Signed-off-by: Paul Spooren <mail@aparcar.org>
Acked-by: Jo-Philipp Wich <jo@mein.io>
Hans Dedecker [Wed, 9 Dec 2020 21:30:38 +0000 (22:30 +0100)]
odhcp6c: update to latest git HEAD
0ffa3a3 dhcpv6: harden reconfigure logic
3999b6d dhcpv6: rework DHCPv6 message to string implementation
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
Brian Norris [Sat, 4 Jul 2020 02:51:57 +0000 (19:51 -0700)]
scripts/feeds: warn when skipping core package override
Otherwise, a n00b like myself can get quite confused when moving a
package from core to feeds, for example.
(Hint: one *really* needs to clear out the tmp/info/.packageinfo...
entries for the stale package, but '-f' works as well.)
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
John Audia [Tue, 8 Dec 2020 14:27:08 +0000 (09:27 -0500)]
kernel: bump 5.4 to 5.4.82
Removed since included upstream and could be reverse-applied by quilt:
backport-5.4/315-v5.10-usbnet-ipeth-fix-connectivity-with-ios-14.patch
Remaining modifications made by update_kernel.sh
Build system: x86_64
Build-tested: ipq806x/R7800, ath79/generic, bcm27xx/bcm2711
Run-tested: ipq806x/R7800
No dmesg regressions, everything functional
Signed-off-by: John Audia <graysky@archlinux.us>
Tested-by: Curtis Deptuck <curtdept@me.com> [build/run x86_64]
Jo-Philipp Wich [Wed, 9 Dec 2020 10:53:04 +0000 (11:53 +0100)]
lldpd: fix autoreconf failure
The lldpd sources ship a modified local AX_LIB_READLINE M4 macro which
conflicts with the official macro shipped by autoconf-archive.
Due to the official macro having the same name and a higher serial
number, autoconf will prefer including that one instead of the local
copy, preventing the substitution of @READLINE_LIBS@ in Makefile.in
templates, ultimately leading to the following build failure when
linking lldpcli:
...-gcc: error: READLINE_LIBS@: No such file or directory
Avoid this problem by renaming the locally shipped macro to not clash
with the official implementation anymore.
Ref: https://github.com/lldpd/lldpd/pull/423
Acked-by: Stijn Tintel <stijn@linux-ipv6.be>
Tested-by: Rosen Penev <rosenp@gmail.com>
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Sieng Piaw Liew [Fri, 9 Oct 2020 09:04:03 +0000 (17:04 +0800)]
bcm63xx: add support for Innacomm W3400V6
Innacomm W3400V6 is an xDSL B/G wireless router based on Broadcom BCM6328 SoC.
Hardware:
SoC: Broadcom BCM6328
CPU: BMIPS4350 V8.0, 320 MHz, 1 core
Flash: SPI-NOR 8MB, MX25L6406E
RAM: 64 MB
Ethernet: 4x 10/100 Mbps
Switch: Integrated
Wireless: 802.11b/g, BCM4312
LEDs/Buttons: 9x / 2x
Flash instruction, web UI:
1) Set a static IP on your computer compatible
with 192.168.1.1, i.e 192.168.1.100
2) Connect the ethernet cable from your computer to the router.
3) Make sure the router is powered off.
4) Press the reset button, don't release it yet!
5) While pressing reset, power on the router.
6) Wait 10 seconds or more.
Note: The power LED is red at first then turns to solid
green when ready.
8) Release the reset button.
9) Browse to 192.168.1.1
10) Select .bin file.
10) Upgrade the image.
11) Wait for it to reboot.
Signed-off-by: Sieng Piaw Liew <liew.s.piaw@gmail.com>
[Ammend commit description, merge patches, DT improvements]
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Sieng Piaw Liew [Fri, 9 Oct 2020 09:01:20 +0000 (17:01 +0800)]
kernel: unlock MX25L6406E with 4 bit Block Protect
Hacked in basic support for 4 bit Block Protection register, copied from
linux-master. Needed to unlock Innacomm W3400V's SPI flash MX25L6406E,
compatible with MX25L6405D.
Signed-off-by: Sieng Piaw Liew <liew.s.piaw@gmail.com>
[Amend commit description, refresh patch]
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Adrian Schmutzler [Tue, 8 Dec 2020 22:45:10 +0000 (23:45 +0100)]
uboot-envtools: ramips: use full names for Xiaomi Mi Routers
This updates uboot-envtools with the updated names from ramips
target.
Fixes: 6d4382711a65 ("ramips: use full names for Xiaomi Mi Router devices")
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Adrian Schmutzler [Tue, 8 Dec 2020 14:05:47 +0000 (15:05 +0100)]
ramips: use full names for Xiaomi Mi Router devices
This aligns the device/image names of the older Xiaomi Mi Router
devices with their "friendly" model and DEVICE_MODEL properties.
This also reintroduces consistency with the newer devices already
following that scheme.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Adrian Schmutzler [Tue, 8 Dec 2020 14:33:32 +0000 (15:33 +0100)]
ramips: mt7628: create shared DTSI for Xiaomi Mi Router 4A/4C
The Xiaomi Mi Router 4A (100M) and 4C are relatively similar in
their specs. Create a shared DTSI for them.
Partitions are split in preparation for Mi Router 4AC.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
John Beckett [Mon, 21 Sep 2020 12:34:17 +0000 (13:34 +0100)]
build: find_md5 list with mod time and sorted
It was observed that the MD5 would not change after source files had been
modified, looking deeper into the build process it was discovered that
find_md5 build function makes a list of the files being built and then
passes the list to a summing utility on stdin. The resultant MD5 is of
the file list, not the contents of the files.
The MD5 would change if the ordering of the list changed, or items were
removed or deleted.
The proposed fix is to add the modification time after the filename and
then sort the list to prevent find returning files in a different order
falsely re-triggering a rebuild. The MD5 will now change when a file is
modified or files are added/removed from the list.
Using 'T@' to show time in epoch for timezone independent behaviour.
Signed-off-by: John Beckett <john.beckett@net2edge.com>
Rosen Penev [Sat, 5 Dec 2020 09:21:05 +0000 (01:21 -0800)]
libcxx[abi]: remove
This is a neat project, but offers no benefit to OpenWrt. The initial
reason for it was to be a replacement for libstdcpp as it is smaller
and lacks compatibility for C++98. Unfortunately, compiling several
packages with it results in larger ipk sizes.
While not a member of the packages feed, this will be moved to
packages-abandoned to keep it somewhere.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Stijn Tintel [Fri, 4 Dec 2020 17:16:26 +0000 (19:16 +0200)]
build: require rsync
It seems to be required to build toolchain/kernel-headers.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Stijn Tintel [Fri, 4 Dec 2020 16:32:46 +0000 (18:32 +0200)]
rules.mk: use -fPIC instead of -fpic on arm64
Some packages fail to build on arm64 when PKG_ASLR_PIE_ALL=y, due to
machine-specific size restrictions on the global offset table.
While the manual instructs to recompile with -fPIC if it fails with
-fpic, by doing this per package, there is still a risk of random
breakage due to version bumps or other changes, so let's use -fPIC on
arm64 by default.
While comparing the sizes of 141 packages built with -fpic vs -fPIC,
most packages are either equal or smaller in size. Only 9 of the
compared packages turned out slightly larger.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Adrian Schmutzler [Tue, 1 Dec 2020 13:48:42 +0000 (14:48 +0100)]
ramips: remove redundant status for USB controllers
mt7621, mt7628an and rt5350 have USB controllers (ehci/ohci or xhci)
enabled by default. Thus, this patch drops redundant status=okay
statements in derived device DTS files.
While at it, also drop an explicit status=okay in mt7621.dtsi, as
this is default.
Note:
For rt5350, about 50 % of the devices enabled ehci/ohci in the DTS
files, and there is actually no device actively disabling it.
It looks like only a few people are aware that the controllers are
enabled by default here.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Adrian Schmutzler [Tue, 1 Dec 2020 13:48:41 +0000 (14:48 +0100)]
ramips: simplify status for ehci/ohci on mt7628 TP-Link devices
At the moment, ehci/ohci is enabled in mt7628an SoC DTSI, then
disabled in the TP-Link-specific DTSI files, and finally enabled
again in the DTS files of the devices needing it.
This on-off-on scheme is hard to grasp on a quick look. Thus, this
patch drops the status in the TP-Link-specific DTSI files, having
the TP-Link devices treated like the rest of mt7628an DTSes, i.e.
ehci/ohci is enabled by default and needs to be disabled explicitly
where needed.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Damien Mascord [Mon, 7 Dec 2020 02:01:38 +0000 (13:01 +1100)]
ath79: add support for Belkin F9J1108v2 (AC1750 DB Wi-Fi)
This device is the non-US build of the F9K1115 v2, with a different
firmware magic.
Specifications:
SoC: QCA9558
CPU: 720 MHz
Flash: 16 MiB NOR
RAM: 128 MiB
WiFi 2.4 GHz: QCA9558-AT4A 3x3 MIMO 802.11b/g/n
WiFi 5 GHz: QCA9880-2R4E 3x3 MIMO 802.11a/n/ac
Ethernet: 4x LAN and 1x WAN (all 1gbps)
USB: 1 x USB 2.0 (lower), 1 x USB 3.0 (upper)
MAC addresses based on OEM firmware:
Interface Address Location
--------- ------- --------
lan *:5A sometimes in 0x6
wan *:5B 0x0
2.4Ghz *:5A 0x1002
5Ghz As per mini PCIe EEPROM
Flashing instructions:
The factory.bin can be flashed via the Belkin web UI or via the uboot
http upgrade page.
Once the factory.bin has been written, sysupgrade.bin will work as usual.
Signed-off-by: Damien Mascord <tusker@tusker.org>
Acked-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
[wrap commit message/code, adjust label-mac-device, whitespace fixes,
merge block in 02_network]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Sander Vanheule [Sat, 15 Aug 2020 07:51:18 +0000 (09:51 +0200)]
firmware-utils: tplink-safeloader: refactor meta-partition padding
Because some padding values in the TP-Link safeloader image generation
were hardcoded, different values were sometimes used throughout a
factory image. TP-Link's upgrade images use the same value everywhere,
so let's do the same here.
Although a lot of TP-Link's safeloader images have padded partition
payloads, images for the EAP-series of AC devices don't. This padding is
therefore also made optional.
By replacing the type of the padding value byte with a wider datatype,
new values outside of the previously valid range become available. Use
these new values to denote that padding should not be performed.
Because char might be signed, also replace the char literals by a
numeric literal. Otherwise '\xff' might be sign extended to 0xffff.
This results in factory images differing by 1 byte for:
* C2600
* ARCHER-C5-V2
* ARCHERC9
* TLWA850REV2
* TLWA855REV1
* TL-WPA8630P-V2-EU
* TL-WPA8630P-V2-INT
* TL-WPA8630P-V2.1-EU
* TLWR1043NDV4
* TL-WR902AC-V1
* TLWR942NV1
* RE200-V2
* RE200-V3
* RE220-V2
* RE305-V1
* RE350-V1
* RE350K-V1
* RE355
* RE450
* RE450-V2
* RE450-V3
* RE500-V1
* RE650-V1
The following factory images no longer have padding, shrinking the
factory images by a few bytes for:
* EAP225-OUTDOOR-V1
* EAP225-V3
* EAP225-WALL-V2
* EAP245-V1
* EAP245-V3
Signed-off-by: Sander Vanheule <sander@svanheule.net>
Sander Vanheule [Wed, 5 Aug 2020 18:49:44 +0000 (20:49 +0200)]
firmware-utils: tplink-safeloader: refactor meta-partition generation
TP-Link safeloader firmware images contain a number of (small)
partitions with information about the device. These consist of:
* The data length as a 32-bit integer
* A 32-bit zero padding
* The partition data, with its length set in the first field
The OpenWrt factory image partitions that follow this structure are
soft-version, support-list, and extra-para. Refactor the code to put all
common logic into one allocation call, and let the rest of the data be
filled in by the original functions.
Due to the extra-para changes, this patch results in factory images that
change by 2 bytes (not counting the checksum) for three devices:
* ARCHER-A7-V5
* ARCHER-C7-V4
* ARCHER-C7-V5
These were the devices where the extra-para blob didn't match the common
format. The hardcoded data also didn't correspond to TP-Link's (recent)
upgrade images, which actually matches the meta-partition format.
A padding byte is also added to the extra-para partition for EAP245-V3.
Signed-off-by: Sander Vanheule <sander@svanheule.net>
Rosen Penev [Sat, 5 Dec 2020 03:20:14 +0000 (19:20 -0800)]
lzo: remove
This is not used by any package in base. It will be moved to packages.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Rosen Penev [Sun, 6 Dec 2020 08:36:05 +0000 (00:36 -0800)]
mtd-utils: remove lzo build dependency
The build option `--withouth-lzo` is added in the Makefile which makes
the existence of lzo obsolete. To remove the lzo package from
openwrt.git entirely, remove the legacy dependency.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
[improved commit message]
Signed-off-by: Paul Spooren <mail@aparcar.org>
Rui Salvaterra [Tue, 27 Oct 2020 09:42:31 +0000 (09:42 +0000)]
kernel: kmod-lib-zstd: enable crypto API support
Zstd is supported by the crypto API since Linux 4.18. Enable this feature and
reveal the package in the configuration section, so the user can select it.
This allows zstd to be used as a compression algorithm in zram, for example.
Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
Nick Lowe [Fri, 4 Dec 2020 17:47:47 +0000 (17:47 +0000)]
hostapd: Disable 802.11b data rates by default
Set legacy_rates to 0 by default to disable 802.11b data rates by default.
The time has long come where 802.11b DSSS/CCK data rates should be disabled
by default in OpenWRT. Users in need of 802.11b client support can reasonably
enable these where they are needed.
The balance of equities has significantly, and for a long time, tipped
such that dropping backwards compatibility by default with 802.11b
devices is appropriate, proportionate and justified. By doing so,
management and control traffic is moved by default to a 20
MHz wide 6 Mb/s OFDM data rate instead of a 22 MHz wide 1 Mb/s DSSS data
rate. This is significantly more airtime efficient.
Signed-off-by: Nick Lowe <nick.lowe@gmail.com>
Álvaro Fernández Rojas [Sun, 6 Dec 2020 18:20:04 +0000 (19:20 +0100)]
bcm63xx: fix ADB P.DG A4001N A-000-1A1-AX LEDs
There's no eth0.2 since all ethernet ports as configured as LAN.
LAN LED is unneeded since all ethernet ports have their own LED.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Daniele Castro [Thu, 10 Sep 2020 19:14:11 +0000 (21:14 +0200)]
bcm63xx: add support for Technicolor TG582n
Technicolor TG582n has a similar PCB as the OpenWrt's ADB P.DG A4001N1
with LEDs connected to different GPIO PINs in active low configuration.
Hardware:
* Board ID: DANT-1
* SoC: Broadcom BCM6328 (rev b0) @ 320MHz, CPU BMIPS4350
* RAM DDR2: 64 Mbyte - Winbond W9751G6KB-25
* Serial flash: 16 Mbyte - MXIC MX25L6445EMI
* Ethernet: 4x Ethernet 10/100 baseT
* Wifi 2.4GHz: Broadcom Corporation BCM43227 Wireless Network Adapter (rev 30)
* LEDs: 2x Power, 1x Ethernet, 1x Broadband, 2x Wi-Fi, 2x WPS, 4x ethernet
* Buttons: 1x Reset, 1x WPS, 1x WiFi
* UART: 1x TTL 115200n8, VCC GND TX RX, on J3 connector (short R62 and R63)
Installation via CFE:
* Stock CFE has to be overwritten with a generic 6328 one that can upload
.bin images with no signature check (cfe6328_configured.bin)
* Connect a serial port to the board
* Stop the CFE boot process after power on by pressing enter
* Set static IP 192.168.2.10 and subnet mask 255.255.255.0
* Navigate to http://192.168.2.50/
* Upload the OpenWrt image file
PCB: |GPIO: |TG582n:
LED2R |488(08) |red Power
LED2G |484(04) |green Power
LED10R |486(06) |
LED13G |485(05) |green Ethernet
LED11R |494(14) |
LED14G |491(11) |green Broadband
LED5R |487(07) |red Internet
LED5G |481(01) |green Internet
LED12R |498(18) |
LED12G |499(19) |
LED6R |482(02) |red Wi-Fi
LED6G |483(03) |green Wi-Fi
LED7R |490(10) |red WPS
LED7G |489(09) |green WPS
LED4 |508(28) |ethernet port 4
LED3 |507(27) |ethernet port 3
LED9 |506(26) |ethernet port 2
LED8 |505(25) |ethernet port 1
SW3 |503(23) |key Reset
SW5 |504(24) |key WPS
SW4 |495(15) |key Wi-Fi
SW6 |493(13) |
SW1 |492(12) |
Signed-off-by: Daniele Castro <danielecastro@hotmail.it>
[Fix base-files, refresh patch]
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Daniele Castro [Tue, 8 Sep 2020 15:16:06 +0000 (17:16 +0200)]
bcm63xx: add support for Technicolor TG582n Telecom Italia branded
Technicolor TG582n Telecom Italia branded a.k.a.
Telecom Italia ADSL2+ Wi-Fi N (AGTWI)
has the same PCB as the unbranded Technicolor TG582n with LEDs
connected to different GPIO PINs in active low configuration and
different LED names. It has a PCB similar to the OpenWrt's ADB P.DG A4001N1 one.
Hardware:
* Board ID: DANT-V
* SoC: Broadcom BCM6328 (rev b0) @ 320MHz, CPU BMIPS4350
* RAM DDR2: 64 Mbyte - EtronTech EM68B16CWQD-25H
* Serial flash: 16 Mbyte - Spansion FL 128SAIF00
* Ethernet: 4x Ethernet 10/100 baseT
* Wifi 2.4GHz: Broadcom Corporation BCM43227 Wireless Network Adapter (rev 30)
* LEDs: 2x Power, 1x ADSL, 2x Internet, 2x Wi-Fi, 2x Service, 4x ethernet
* Buttons: 1x Reset, 1x WPS (named WiFi/LED)
* UART: 1x TTL 115200n8, VCC GND TX RX, on J3 connector (short R62 and R63)
Installation via CFE:
* Stock CFE has to be overwritten with a generic 6328 one that can upload
.bin images with no signature check (cfe6328_configured.bin)
* Connect a serial port to the board
* Stop the CFE boot process after power on by pressing enter
* Set static IP 192.168.2.10 and subnet mask 255.255.255.0
* Navigate to http://192.168.2.50/
* Upload the OpenWrt image file
PCB: |GPIO: |TG582n: |AGTWI:
LED2R |488(08) |red Power |red Power
LED2G |484(04) |green Power |green Power
LED10R |486(06) | |missing R85 end LED
LED13G |485(05) |green Ethernet |green ADSL
LED11R |494(14) | |red Internet
LED14G |491(11) |green Broadband |green Internet
LED5R |487(07) |red Internet |red Wi-Fi
LED5G |481(01) |green Internet |green Wi-Fi
LED12R |498(18) | |red Service
LED12G |499(19) | |green Service
LED6R |482(02) |red Wi-Fi |missing R108 end LED
LED6G |483(03) |green Wi-Fi |missing R107 end LED
LED7R |490(10) |red WPS |missing R91 end LED
LED7G |489(09) |green WPS |missing R92 end LED
LED4 |508(28) |ethernet port 4 |ethernet port 4
LED3 |507(27) |ethernet port 3 |ethernet port 3
LED9 |506(26) |ethernet port 2 |ethernet port 2
LED8 |505(25) |ethernet port 1 |ethernet port 1
SW3 |503(23) |key Reset |key Reset
SW5 |504(24) |key WPS |key Wi-Fi/LED
SW4 |495(15) |key Wi-Fi |missing R127 end key
SW6 |493(13) | |missing R171 end key
SW1 |492(12) | |missing R1 end key
Signed-off-by: Daniele Castro <danielecastro@hotmail.it>
[DT fixes, base-files fixes and device variant]
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Eneas U de Queiroz [Sat, 28 Nov 2020 21:06:33 +0000 (18:06 -0300)]
openssl: use --cross-compile-prefix in Configure
This sets the --cross-compile-prefix option when running Configure, so
that that it will not use the host gcc to figure out, among other
things, compiler defines. It avoids errors, if the host 'gcc' is
handled by clang:
mips-openwrt-linux-musl-gcc: error: unrecognized command-line option
'-Qunused-arguments'
Signed-off-by: Eneas U de Queiroz <cotequeiroz@gmail.com>
Tested-by: Rosen Penev <rosenp@gmail.com>
Daniele Castro [Wed, 9 Sep 2020 01:21:14 +0000 (03:21 +0200)]
bcm63xx: add support for ADB P.DG A4101N A-000-1A1-AE
ADB P.DG A4101N A-000-1A1-AE has a similar PCB as the OpenWrt's ADB P.DG A4001N1
with LEDs connected to different GPIO PINs in active low configuration.
Hardware:
* Board ID: 96328avngv
* SoC: Broadcom BCM6328 (rev b0) @ 320MHz, CPU BMIPS4350
* RAM DDR2: 64 Mbyte - Winbond W9751G6KB-25
* Serial flash: 16 Mbyte - Winbond 25Q128BVFG
* Ethernet: 4x Ethernet 10/100 baseT
* Wifi 2.4GHz: Broadcom Corporation BCM43225 Wireless Network Adapter (rev 23)
* LEDs: 1x Power, 1x DSL, 1x Internet, 4x ETH, 1x USB, 1x WLAN, 1x WPS, 1x TEL
* Buttons: 1x Reset, 1x WPS, 1x unnamed
* UART: 1x TTL 115200n8, VCC RX TX GND, on J502 connector
Installation via CFE:
* Stock CFE has to be overwritten with a generic 6328 one that can upload
.bin images with no signature check (cfe6328_configured.bin)
* Connect a serial port to the board
* Stop the cfe boot process after power on by pressing enter
* Set static IP 192.168.2.10 and subnet mask 255.255.255.0
* Navigate to http://192.168.2.50/
* Upload the OpenWrt image file
A4101N GPIO LAYOUT:
Power always on
DSL GPIO483(03)
Internet GPIO491(11)
ETH1 GPIO505(25)
ETH2 GPIO506(26)
ETH3 GPIO507(27)
ETH4 GPIO508(28)
USB GPIO490(10)
WLAN controlled by BCM43225
WPS GPIO489(09)
TEL GPIO511(31)
Key RESET GPIO503(23)
Key WPS GPIO504(24)
Key unnamed GPIO492(12)
Signed-off-by: Daniele Castro <danielecastro@hotmail.it>
[Amend commit description, DTS improvements, refresh patches]
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Sven Roederer [Sat, 5 Dec 2020 22:15:53 +0000 (23:15 +0100)]
procd: also depend on jshn
fixes "file no found" error on stripped down images, caused by prod.sh:43.
Signed-off-by: Sven Roederer <devel-sven@geroedel.de>
Paul Spooren [Mon, 21 Sep 2020 22:43:43 +0000 (12:43 -1000)]
build: reduce cleanup binary calls in rootfs.mk
Both `find` and `rm` only need to be called once for folders and files.
Signed-off-by: Paul Spooren <mail@aparcar.org>
Rosen Penev [Tue, 1 Dec 2020 20:37:02 +0000 (12:37 -0800)]
openvpn: remove
This will be moved to packages.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Acked-by: Paul Spooren <mail@aparcar.org>
Rosen Penev [Tue, 1 Dec 2020 20:37:01 +0000 (12:37 -0800)]
openvpn-easy-rsa: remove
This will be moved to packages.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Hans Dedecker [Sat, 5 Dec 2020 19:52:27 +0000 (20:52 +0100)]
glibc: update to latest 2.32 commit (BZ# 26224)
050022910b iconv: Accept redundant shift sequences in IBM1364 [BZ #26224]
ac0a6929c5 sh: Add sh4 fpu Implies folder
3ea24955bf struct _Unwind_Exception alignment should not depend on compiler flags
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
Hans Dedecker [Sat, 5 Dec 2020 19:45:29 +0000 (20:45 +0100)]
odhcp6c: update to git HEAD
faed29a dhcpv6: only refresh timers when reconfigure is valid
9c50975 dhcpv6: fix printing identity association id
a7b2221 dhcpv6: avoid sending continuous renew/rebind messages
d7afa2b dhcpv6: add extra syslog info traces
f5728e4 odhcp6c_find_entry: exclude priority from the list of fields that must match
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
Felix Fietkau [Thu, 26 Nov 2020 15:12:12 +0000 (16:12 +0100)]
build: make testing kernel decompression more portable
On non-GNU systems, zcat often does not handle gzip decompression.
Use gzip -dc like the regular unpack command
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Felix Fietkau [Thu, 26 Nov 2020 16:29:11 +0000 (17:29 +0100)]
kernel: remove an unused callback from the ip17xx switch driver
Also remove the leftover kernel hack that adds support for it
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Ahmed Naseef [Tue, 18 Aug 2020 12:22:20 +0000 (17:52 +0530)]
bcm63xx: Add support for D-Link DSL-2750u rev C1
This adds support for the D-Link DSL-2750u rev C1.
(https://deviwiki.com/wiki/D-Link_DSL-2750U_rev_C1)
It uses the same hardware as ADB P.DG A4001N.
CPU: Broadcom BCM63281 (320 MHz)
RAM: 32M (Winbond W9725G6JB)
Flash: 8M (MXIC MX25L6445E)
Ethernet: 4x 100 Mbps
Wireless: 802.11b/g/n: BCM43225
USB: 1x 2.0
Flash instructions:
1. Assign static IP 192.168.1.100 to PC
2. Unplug the power source
3. Press the RESET button at the router, don't release it yet!
4. Plug the power source.Wait some seconds
5. Release the RESET button
6. Browse to http://192.168.1.1
7. Send the openwrt-bcm63xx-generic-DSL2750U-C1-squashfs-cfe.bin and
wait some minutes until the firmware upgrade finish.
Signed-off-by: Ahmed Naseef <naseefkm@gmail.com>
[DTS improvements, proper board patch, refresh patches]
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Daniele Castro [Sat, 5 Sep 2020 15:33:23 +0000 (17:33 +0200)]
bcm63xx: A4001N A-000-1A1-AX: remove PSI (nvram) partition
ADB P.DG A4001N A-000-1A1-AX a.k.a. Telecom Italia ADSL2+ Wi-Fi N (AGPWI)
is a Telecom Italia braded router and it seems that there are no public
available unbranded versions of this router.
The stock Telecom Italia braded firmware has many partitions and the
partition layout changes with every firmware relase.
The PSI nvram partition is present in the stock firmware under the
"UNKNOWN" name but it's empty, full of FFs. Since removing partitions
does not cause problems with the stock firmware reflashing procedure,
I removed from the dts the PSI nvram partition from OpenWrt, expanded
the rootfs one and added the NVRAM partition contained in the
cfe bootloader.
Furthermore this router's flash needs to be entirely reprogrammed
and a new generic bcm6328 cfe must be flashed to boot OpenWrt. The
same process takes place when reflashing the stock firmware.
Here follows the original flash layout for AGPWI_1.1.0_013, the last
stock Telecom Italia braded firmware for which we have root
credentials (admin/riattizzati).
Flash layout:
Section 00 Type BOOT Range 0x00000000-0x00020000 MaxSize 0x00020000
No more information.
Section 01 Type IMAGE Range 0x00020000-0x007C0000 MaxSize 0x0079FF6C
Uninitialized.
Section 02 Type IMAGE Range 0x00800000-0x00FA0000 MaxSize 0x0079FF6C
Uninitialized.
Section 03 Type CONF Range 0x00FA0000-0x00FC0000 MaxSize 0x0001FF6C
Size 0x0000841E Name 'rg_conf'
Checksum 0x0041E03B Counter 0x0000051F Start Offset 0x00000000
Section 04 Type CONF Range 0x00FC0000-0x00FE0000 MaxSize 0x0001FF6C
Size 0x0000838E Name 'rg_conf'
Checksum 0x00419A5A Counter 0x00000522 Start Offset 0x00000000
Section 05 Type FACTORY Range 0x00FE0000-0x00FF0000 MaxSize 0x0000FF6C
Size 0x00000554 Name 'rg_factory'
Checksum 0x0001255E Counter 0x000004D3 Start Offset 0x00000000
Section 06 Type UNKNOWN Range 0x00FF0000-0x01000000 MaxSize 0x00010000
No more information.
Total 7 sections found.
The last AGPWI firmware relase should be AGPWI_4.0.6 and it has much more
partitions than AGPWI_1.1.0_013.
The cfe partition in the stock firmware is 0x00020000 bytes long unlike the
OpenWrt dts in wich it's 0x00010000 bytes long because from 0x00010000 to
0x00020000 in the stock cfe there are only 00s and also because the cfe must
anyway be reflashed with a generic bcm6328 cfe 0x00010000 bytes long to
run OpenWrt.
Signed-off-by: Daniele Castro <danielecastro@hotmail.it>
[Amend commit, remove unneeded cfe_nvram partition]
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Sieng Piaw Liew [Thu, 12 Nov 2020 18:21:07 +0000 (02:21 +0800)]
bcm63xx: support xmit_more in BQL
Support bulking hardware TX queue by using xmit_more.
Signed-off-by: Sieng Piaw Liew <liew.s.piaw@gmail.com>
[Amend commit description, fix kernel xmit_more exceptions]
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Sieng Piaw Liew [Thu, 12 Nov 2020 18:20:30 +0000 (02:20 +0800)]
bcm63xx: add BQL support
Add Byte Queue Limits support to reduce/remove bufferbloat in bcm63xx target.
Signed-off-by: Sieng Piaw Liew <liew.s.piaw@gmail.com>
[Amend commit description]
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Adrian Schmutzler [Fri, 14 Aug 2020 11:09:12 +0000 (13:09 +0200)]
ath79: add support for TP-Link TL-WDR7500 v3
This ports support for the TP-Link TL-WDR7500 v3 from ar71xx to ath79.
The basic features appear to be identical to the Archer C7 v1, however
it has the (supported) QCA9880-BR4A chip of the C7 v2.
Specifications:
SoC: QCA9558
CPU: 720 MHz
Flash: 8 MiB
RAM: 128 MiB
WLAN: 2.4 GHz b/g/n, 5 GHz a/n/ac
Qualcomm Atheros QCA9880-BR4A
Ethernet: 5x Gbit ports
USB: 2x 2.0 ports
Flashing instructions:
Upload the factory image via the OEM firmware GUI.
TFTP recovery appears to be available as well.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
John Audia [Wed, 2 Dec 2020 11:45:04 +0000 (06:45 -0500)]
kernel: bump 5.4 to 5.4.81
All modifications made by update_kernel.sh/no human intervention needed
Build system: x86_64
Build-tested: ipq806x/R7800, ath79/generic, bcm27xx/bcm2711
Run-tested: ipq806x/R7800
No dmesg regressions, everything functional
Signed-off-by: John Audia <graysky@archlinux.us>
[another refresh]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Adrian Schmutzler [Tue, 1 Dec 2020 13:14:59 +0000 (14:14 +0100)]
ramips: drop redundant status for gpio/gpio0
The first gpio controller (gpio or gpio0) is always enabled by
default in the SoC DTSI files. No need to set status=okay in the
device DTS files a second time.
Remove the redundant statements.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Adrian Schmutzler [Sun, 29 Nov 2020 17:03:48 +0000 (18:03 +0100)]
ath79: drop num-cs for SPI controller
None of the spi drivers on ath79 uses the num-cs property.
Cc: Chuanhong Guo <gch981213@gmail.com>
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Acked-by: Chuanhong Guo <gch981213@gmail.com>
Adrian Schmutzler [Sun, 29 Nov 2020 16:07:17 +0000 (17:07 +0100)]
ath79: remove num-chipselects from SPI controller
The num-chipselects property is only valid for bit-banged spi-gpio [1].
For the generic SPI controller bindings, num-cs would be the correct
property [2].
Since num-cs is not required on ath79 either, just drop the lines.
[1] https://www.kernel.org/doc/Documentation/devicetree/bindings/spi/spi-gpio.yaml
[2] https://www.kernel.org/doc/Documentation/devicetree/bindings/spi/spi-controller.yaml
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Daniel Golle [Fri, 4 Dec 2020 14:39:40 +0000 (14:39 +0000)]
procd: output warning if user 'ubus' doesn't exist
6acc48c early: fall-back to run ubus as root if user can't be found
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Daniel Golle [Fri, 4 Dec 2020 14:38:24 +0000 (14:38 +0000)]
ubus: make sure ubusd starts in case user 'ubus' doesn't exist
d1d9ddf ubusd: attempt to create socket folder
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Mengyang Li [Sat, 24 Oct 2020 00:07:18 +0000 (17:07 -0700)]
x86: enable CONFIG_MMC_SDHCI_ACPI for x86_64
Some x86_64 single board computer (including Atomic Pi)
has onboard emmc, but requires CONFIG_MMC_SDHCI_ACPI driver
to use or boot from it.
Here is boot message for the mmc device
[ 2.838008] mmc0: SDHCI controller on ACPI [
80860F14:00] using ADMA
[ 2.857536] mmc1: SDHCI controller on ACPI [
80860F14:01] using ADMA
[ 2.950019] mmc0: new HS200 MMC card at address 0001
[ 3.158271] mmcblk0: mmc0:0001 M52516 14.6 GiB
[ 3.170290] mmcblk0boot0: mmc0:0001 M52516 partition 1 4.00 MiB
[ 3.177191] mmcblk0boot1: mmc0:0001 M52516 partition 2 4.00 MiB
[ 3.183963] mmcblk0rpmb: mmc0:0001 M52516 partition 3 4.00 MiB, \
chardev (248:0)
Other lines changed in this config file are introduced by menuconfig.
Signed-off-by: Mengyang Li <mayli.he@gmail.com>
Stan Grishin [Mon, 12 Oct 2020 22:03:15 +0000 (22:03 +0000)]
base-files: informative service command in /etc/shinit. service command shows services enabled/disabled and running status, when the service command is invoked with no/invalid arguments, like this:
Usage: service <service> [command]
The following services are available:
/etc/init.d/acme enabled stopped
/etc/init.d/boot enabled stopped
/etc/init.d/cron enabled running
/etc/init.d/dnsmasq enabled running
...
Signed-off-by: Stan Grishin <stangri@melmac.net>
Daniele Castro [Mon, 14 Sep 2020 01:49:30 +0000 (03:49 +0200)]
brcm63xx: add USB status LED in 01_leds for ADP P.DG A4001N
Add a status LED in 01_leds for USB 2-1 connected devices.
Signed-off-by: Daniele Castro <danielecastro@hotmail.it>
Hauke Mehrtens [Wed, 23 Sep 2020 01:25:30 +0000 (03:25 +0200)]
build: Extract trusted-firmware-a.mk
The include/trusted-firmware-a.mk file is based on the
include/u-boot.mk file and should be used to build a Trusted Firmware-A
(TFA) which was previously named Arm trusted firmware.
This is useful for targets where the TFA is board specific like for
Marvell SoCs and probably also NXP Layerscape SoCs.
This also makes use of this abstraction in the
arm-trusted-firmware-mvebu package to build board specific ATF binaries.
The ATF binaries will be automatically activated and build when the
board is selected in the normal build or all boards are selected. This
should also activate the build when build bot creates images.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Hauke Mehrtens [Wed, 2 Dec 2020 21:06:34 +0000 (22:06 +0100)]
toolchain: musl: refresh patches
Refresh the musl patches
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
David Bauer [Sun, 29 Nov 2020 13:48:15 +0000 (14:48 +0100)]
ath79: remove ar934x MDIO reset from MAC node
Remove the MDIO reset from the MAC mode for the AR934x SoC family.
The reset is currently also defined for the MDIO node, where the reset
is acquired exclusively.
In case the ethernet node is enabled, this triggers a warning, as the
reset is already acquired by the MAC.
Signed-off-by: David Bauer <mail@david-bauer.net>
Sieng Piaw Liew [Mon, 2 Nov 2020 03:12:19 +0000 (11:12 +0800)]
bcm63xx: enetsw: switch to netdev_alloc_skb_ip_align
Increases packet processing performance by 30%.
Tested on BCM6328 320 MHz and iperf3 -M 512 for packet/sec performance.
Before:
[ ID] Interval Transfer Bandwidth Retr
[ 4] 0.00-30.00 sec 120 MBytes 33.7 Mbits/sec 277 sender
[ 4] 0.00-30.00 sec 120 MBytes 33.5 Mbits/sec receiver
After:
[ ID] Interval Transfer Bandwidth Retr
[ 4] 0.00-30.00 sec 155 MBytes 43.3 Mbits/sec 354 sender
[ 4] 0.00-30.00 sec 154 MBytes 43.1 Mbits/sec receiver
Signed-off-by: Sieng Piaw Liew <liew.s.piaw@gmail.com>
[Merge patches, amend commit and add patch description]
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Sieng Piaw Liew [Mon, 30 Nov 2020 03:32:18 +0000 (11:32 +0800)]
bcm63xx: batch process RX path
Use netif_receive_skb_list to batch process skb in RX.
Tested on BCM6328 320 MHz using iperf3 -M 512, increasing performance by 12.5%.
Before:
[ ID] Interval Transfer Bandwidth Retr
[ 4] 0.00-30.00 sec 120 MBytes 33.7 Mbits/sec 277 sender
[ 4] 0.00-30.00 sec 120 MBytes 33.5 Mbits/sec receiver
After:
[ ID] Interval Transfer Bandwidth Retr
[ 4] 0.00-30.00 sec 136 MBytes 37.9 Mbits/sec 203 sender
[ 4] 0.00-30.00 sec 135 MBytes 37.7 Mbits/sec receiver
Signed-off-by: Sieng Piaw Liew <liew.s.piaw@gmail.com>
[Amend commit description]
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Thomas Huehn [Wed, 2 Dec 2020 10:24:07 +0000 (11:24 +0100)]
ath79: enable LNA for all ar9344 TPLink CPE devices
The TPLink CPE devices CPE210/CPE510 based on ar9344 have a build-in
Low Noise Amplifier on both of the 2x2 mimo rx chains.
This patch activates those two LNAs in the respective receiving chains
and hence improves the RX sensitivity by about 20dB.
Tested on CPE510 v2 & v3.
Signed-off-by: Thomas Huehn <thomas.huehn@hs-nordhausen.de>
Acked-by: Robert Marko <robimarko@gmail.com>
Felix Fietkau [Wed, 2 Dec 2020 11:08:17 +0000 (12:08 +0100)]
netifd: update to the latest version
d6bd1047d004 vlandev: dump vlan id in device status
e0c838bd06a6 vlandev: support bridge-vlan aliases in the vid config parameter
574dc4a17105 system-dummy: print configured mac address
14f0e8ff928f system-linux: simplify mask check in system_if_apply_settings
524310276f20 system-linux: move device settings handling to device.c
42c48866f1c1 config: parse default mac address from board.json
Signed-off-by: Felix Fietkau <nbd@nbd.name>
John Crispin [Wed, 2 Dec 2020 09:41:19 +0000 (10:41 +0100)]
realtek: fix SFP ports on the dlink 10port switch
Signed-off-by: John Crispin <john@phrozen.org>
John Crispin [Tue, 1 Dec 2020 16:13:39 +0000 (17:13 +0100)]
realtek: add zyxel_gs1900-10hp support
Signed-off-by: John Crispin <john@phrozen.org>
John Crispin [Sat, 28 Nov 2020 10:50:43 +0000 (11:50 +0100)]
realtek: cleanup package selection
Signed-off-by: John Crispin <john@phrozen.org>
John Crispin [Sat, 28 Nov 2020 10:44:44 +0000 (11:44 +0100)]
realtek: clean up board.json generation
In this new setup the switch is treated as wan, lan1.100 is used as
our mgmt vlan.
The board mac is applied to eth0, switch and switch.1
The board mac is assigned with the LA bit set to all lan ports while
incrementing it.
Signed-off-by: John Crispin <john@phrozen.org>
John Crispin [Sat, 28 Nov 2020 10:43:47 +0000 (11:43 +0100)]
base-files: allow setting device and bridge macs
Add code for setting mac addresses inside board.json and rendering
them out to uci. On switches we want to have a unique MAC on each port.
With 48 port switches that would require 48 device sections in
/etc/config/network. Doing so via board.json is easier.
Signed-off-by: John Crispin <john@phrozen.org>
John Crispin [Sat, 28 Nov 2020 10:46:47 +0000 (11:46 +0100)]
uboot-envtools: add support for the realtek target
On most boards the MAC is located inside the u-boot-env.
Signed-off-by: John Crispin <john@phrozen.org>
projects / openwrt / staging / aparcar.git / log