wireless: unify QoS control field definitions

Move all that mac80211 has into the generic
ieee80211.h header file and use them. At the
same time move them from mask+shift to just
bits and rename them for consistent names.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ssb: fix ssb clock rate according to broadcom source

This fix was done according to si_clock_rate function in broadcom siutils.c

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rtlwifi: rtl8192de: Modify Kconfig and Makefile routines for new driver

Set up Kconfig and Makefile for new driver for RTL8192DE.

Signed-off-by: Chaoming_Li <chaoming_li@realsil.com.cn>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rtlwifi: Fix build problems introduced by merging rtl8192de

These patches allow compilation of rtlwifi, rtl8192c_common,
rtl8192ce, rtl8192cu and rtl8192se to compile after rtl8192de
was added.

Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rtlwifi: rtl8192de: Merge TX and RX routines

Merge routines trx.c and trx.h for RTL8192DE.

Signed-off-by: Chaoming_Li <chaoming_li@realsil.com.cn>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rtlwifi: rtl8192de: Merge table routines

Merge routines table.c and table.h for RTL8192DE.

Signed-off-by: Chaoming_Li <chaoming_li@realsil.com.cn>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rtlwifi: rtl8192de: Merge main (sw) routines

Merge routines sw.c and sw.h for RTL8192SE.

Signed-off-by: Chaoming_Li <chaoming_li@realsil.com.cn>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rtlwifi: rtl8192de: Merge rf routines

Merge routines rf.c and rf.h for RTL8192DE.

Signed-off-by: Chaoming_Li <chaoming_li@realsil.com.cn>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rtlwifi: rtl8192de: Merge register definitions

Merge routines reg.h for RTL8192DE.

Signed-off-by: Chaoming_Li <chaoming_li@realsil.com.cn>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rtlwifi: rtl8192de: Merge phy routines

Merge routines phy.c and phy.h for RTL8192DE.

Signed-off-by: Chaoming_Li <chaoming_li@realsil.com.cn>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rtlwifi: rtl8192de: Merge led routines

Merge routines led.c and led.h for RTL8192DE.

Signed-off-by: Chaoming_Li <chaoming_li@realsil.com.cn>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rtlwifi: rtl8192de: Merge hardware routines

Merge routines hw.c and hw.h for RTL8192DE.

Signed-off-by: Chaoming_Li <chaoming_li@realsil.com.cn>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rtlwifi: rtl8192de: Merge firmware routines

Merge routines fw.c and fw.h for RTL8192DE.

Signed-off-by: Chaoming_Li <chaoming_li@realsil.com.cn>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rtlwifi: rtl8192de: Merge dynamic management routines

Merge routines dm.c and dm.h for RTL8192DE.

Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Chaoming_Li <chaoming_li@realsil.com.cn>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rtlwifi: rtl8192de: Merge def.h

Introduce routine def.h for rtl8192de.

Signed-off-by: Chaoming_Li <chaoming_li@realsil.com.cn>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Merge branch 'wireless-next-2.6' of git://git./linux/kernel/git/iwlwifi/iwlwifi-2.6

Bluetooth: include scatterlist.h where needed

net/bluetooth/smp.c: In function 'smp_e':
net/bluetooth/smp.c:49:21: error: storage size of 'sg' isn't known
net/bluetooth/smp.c:67:2: error: implicit declaration of function 'sg_init_one'
net/bluetooth/smp.c:49:21: warning: unused variable 'sg'

Caused by commit d22ef0bc83c5 ("Bluetooth: Add LE SMP Cryptoolbox
functions").  Missing include file, presumably.  This batch has been in
the bluetooth tree since June 14, so it may have been exposed by the
removal of linux/mm.h from netdevice.h ...

Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

iwlagn: don't use CCK rates for P2P interfaces

P2P interfaces must not use CCK rates, only OFDM
rates are allowed. To set this up, we need to set
up the broadcast station to start with 6M instead
of starting with 1M.

Since the interface type can change, also reset
the broadcast station when RXON changes.

This will affect beacons as well.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>

iwlagn: fill beacon TX rate properly

Use the rate that mac80211 requested to fill the
uCode TX command for the beacon. Unfortunately,
the uCode is (currently?) ignoring it, but now
at least fill it properly.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>

iwlagn: extend host command timeout

We've infrequently seen timeouts, make the wait time
match the windows driver; hopefully our driver is
just too impatient.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>

iwlagn: fix cmd queue unmap

When we stop the device while a command is in
flight that uses multiple TBs, we can leak the
DMA buffers for the second and higher TBs. Fix
this by using iwlagn_unmap_tfd() as we do when
we normally recover the entry.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>

iwlagn: use PM ops macro

Simplify the code and use SIMPLE_DEV_PM_OPS
to define iwl_dev_pm_ops instead of doing the
same thing manually.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>

ssb: add __devinit to some functions

Two functions in ssb are using register_pci_controller() which is
__devinit. The functions ssb_pcicore_init_hostmode() and
ssb_gige_probe() should also be __devinit.

This fixes the following warning:
WARNING: vmlinux.o(.text+0x2727b8): Section mismatch in reference from the function ssb_pcicore_init_hostmode() to the function .devinit.text:register_pci_controller()
The function ssb_pcicore_init_hostmode() references
the function __devinit register_pci_controller().
This is often because ssb_pcicore_init_hostmode lacks a __devinit
annotation or the annotation of register_pci_controller is wrong.

WARNING: vmlinux.o(.text+0x273398): Section mismatch in reference from the function ssb_gige_probe() to the function .devinit.text:register_pci_controller()
The function ssb_gige_probe() references
the function __devinit register_pci_controller().
This is often because ssb_gige_probe lacks a __devinit
annotation or the annotation of register_pci_controller is wrong.

Reported-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: enable support for AR9330

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: add external_reset callback to ath9k_platfom_data for AR9330

The patch adds a callback to ath9k_platform_data. If the
callback is provided by the platform code, then it can be
used to hard reset the WMAC device.

The callback is required for doing a hard reset of the AR9330
chips to get them working again after a hang.

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: configure internal regulator for AR9330

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: configure diversity based on eeprom contents for AR9330

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: fix few register offsets for AR9330

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: set diversity group for AR9330

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: add fast_div_bias configuration for diversity group 1

The patch adds the missing configuration code for diversity
group 1.

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: remove superfluous parentheses

Also remove two empty lines.

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: fix antenna diversity configuration for non AR9485 chips

The current values must be used only on AR9485 chips. Other chips
requires different values.

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: add a missing case statement to ath_ant_div_comb_alt_check

The 'ar9003_hw_antdiv_comb_conf_get' function sets div_group to 2
however that value is not used in 'ath_ant_div_comb_alt_check'.

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: use correct max_streams for AR9330

The AR9330 is a single stream chip.

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: enable antenna diversity for AR9330

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: set NF limits for AR9330

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: configure xpa bias level for AR9330

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: use correct EEPROM base for AR9330

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: enable tuning capacitance configuration for AR9330

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: skip internal regulator configuration for AR9330

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: enable TX/RX data byte swap for AR9330

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: configure RF channel frequency for AR9330

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: fix channel frequency calculation for AR9340

A multiplication is missing from the current formula.

Cc: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: read spur frequency information from eeprom for AR9330

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: don't enable LDPC for AR9330

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: use different BB watchdog timeout value for AR9330

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: add AR9330 specific PLL initialization

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: initialize rx gain table for AR9330

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: initialize tx gain table for AR9330

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: initialize mode registers for AR9330

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: add AR9330 initvals

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: add platform device id for AR9330

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: add MAC revision detection for AR9330

The AR9330 1.0 and 1.1 are using the same revision,
thus it is not possible to distinguish the two chips.
The platform setup code can distinguish the chips based
on the SoC revision.

Add a callback function to ath9k_platform_data in order
to allow getting the revision number from the platform code.

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: define device id for AR9330

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: define mac version for AR9330

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k_hw: Fix calculation of PAPRD training power at 5Ghz

higher the chainmask, lesser the power_delta to be added
to the paprd_training_power

Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

nl80211: use netlink consistent dump feature for BSS dumps

Use the new consistent dump feature from (generic) netlink
to advertise when dumps are incomplete.

Readers may note that this does not initialize the
rdev->bss_generation counter to a non-zero value. This is
still OK since the value is modified only under spinlock
when the list is modified. Since the dump code holds the
spinlock, the value will either be > 0 already, or the
list will still be empty in which case a consistent dump
will actually be made (and be empty).

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mwifiex: remove casts of void pointers

In some cases local pointers are used to cast void pointers passed to
the function. Those unnecessary local pointers are also removed.

This patch was inspired by Joe Perches' patch
[PATCH net-next 1/2] wireless: Remove casts of void *;
and the comments from Julian Calaby.

Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Cc: Joe Perches <joe@perches.com>
Cc: Julian Calaby <julian.calaby@gmail.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

zd1211rw: detect stalled beacon interrupt faster

As USB_INT_ID_RETRY_FAILED can override USB_INT_ID_REGS, beacon interrupt
(CR_INTERRUPT) might be lost. Problem is that when device trigger CR_INTERRUPT
it disables HW interrupt. Now if USB_INT_ID_REGS with CR_INTERRUPT gets lost,
beacon interrupt stays disabled until beacon watchdog notices the stall. This
happen very often on heavy TX. Improve watchdog to trigger earlier, after three
missing beacon interrupts.

Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

zd1211rw: don't let zd_mac_config_beacon() run too long from beacon interrupt handler

zd_mac_config_beacon() has only limited time to set up beacon when called from
beacon interrupt handler/worker. So do not let it retry acquiring beacon fifo
semaphore in interrupt handler. Beacon fifo semaphore should not be locked by
firmware anyway at this time, it's only locked when device is using/txing
beacon.

Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

zd1211rw: handle lost read-reg interrupts

Device losses read-reg interrupts. By looking at usbmon it appears that
USB_INT_ID_RETRY_FAILED can override USB_INT_ID_REGS. This causes read
command to timeout, usually under heavy TX.

Fix by retrying read registers again if USB_INT_ID_RETRY_FAILED is received
while waiting for USB_INT_ID_REGS.

However USB_INT_ID_REGS is not always lost but is received after
USB_INT_ID_RETRY_FAILED and is usually received by the retried read
command. USB_INT_ID_REGS of the retry is then left unhandled and might
be received by next read command. Handle this by ignoring previous
USB_INT_ID_REGS that doesn't match current read command request.

Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

zd1211rw: only update HW beacon if new beacon differs from currect

Update HW beacon only when needed. This appears to make device work in AP-mode
(dtim_period=1) somewhat more stable.

Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

zd1211rw: make 'handle_rx_packet: invalid, small RX packet' message debug-only

This message is should be debug-only as it tells almost nothing useful. It also
happens very often and just floods logs.

Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

zd1211rw: fix invalid signal values from device

Driver uses IEEE80211_HW_SIGNAL_UNSPEC and so signal values reported to
mac80211 should be in range 0..100. Sometimes device return out of range
values. These out of range values can then trigger warning in
cfg80211_inform_bss_frame.

This patch adds checks to enforce range returned from driver to
mac80211 be in 0..100 range.

Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

netlink: advertise incomplete dumps

Consider the following situation:
 * a dump that would show 8 entries, four in the first
   round, and four in the second
 * between the first and second rounds, 6 entries are
   removed
 * now the second round will not show any entry, and
   even if there is a sequence/generation counter the
   application will not know

To solve this problem, add a new flag NLM_F_DUMP_INTR
to the netlink header that indicates the dump wasn't
consistent, this flag can also be set on the MSG_DONE
message that terminates the dump, and as such above
situation can be detected.

To achieve this, add a sequence counter to the netlink
callback struct. Of course, netlink code still needs
to use this new functionality. The correct way to do
that is to always set cb->seq when a dumpit callback
is invoked and call nl_dump_check_consistent() for
each new message. The core code will also call this
function for the final MSG_DONE message.

To make it usable with generic netlink, a new function
genlmsg_nlhdr() is needed to obtain the netlink header
from the genetlink user header.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

b43: HT-PHY: calibrate radio after switching channel

After uploading radio values calibration goes in. In MMIO dump it is:
 radio_read(0x002b) -> 0x0008
radio_write(0x002b) <- 0x0008
 radio_read(0x002e) -> 0x0004
radio_write(0x002e) <- 0x0000
 radio_read(0x002e) -> 0x0000
radio_write(0x002e) <- 0x0004
 radio_read(0x002b) -> 0x0008
radio_write(0x002b) <- 0x0009
To find masks and sets, MMIO hacks were used to fool closed driver.

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rt2x00: reset usb devices at probe

When module is reloaded, device may fail to work, with messages:

[  342.211926] phy40 -> rt2x00lib_rxdone_read_signal: Warning - Frame received with unrecognized signal, mode=0x0000, signal=0x0059, type=2.
[  342.314254] phy40 -> rt2x00lib_rxdone_read_signal: Warning - Frame received with unrecognized signal, mode=0x0000, signal=0x004a, type=2.
[  342.416458] phy40 -> rt2x00lib_rxdone: Warning - Wrong frame size 3183 max 2432.
[  342.518605] phy40 -> rt2x00lib_rxdone_read_signal: Warning - Frame received with unrecognized signal, mode=0x0000, signal=0x00c9, type=2.
[  342.620836] phy40 -> rt2x00lib_rxdone_read_signal: Warning - Frame received with unrecognized signal, mode=0x0000, signal=0x00ae, type=1.
[  342.723201] phy40 -> rt2x00lib_rxdone: Warning - Wrong frame size 0 max 2432.
[  342.825399] phy40 -> rt2x00lib_rxdone: Warning - Wrong frame size 0 max 2432.
[  342.927624] phy40 -> rt2x00lib_rxdone: Warning - Wrong frame size 0 max 2432.
[  343.029804] phy40 -> rt2x00lib_rxdone: Warning - Wrong frame size 2491 max 2432.
[  343.132008] phy40 -> rt2x00lib_rxdone: Warning - Wrong frame size 2576 max 2432.
[  343.234326] phy40 -> rt2x00lib_rxdone_read_signal: Warning - Frame received with unrecognized signal, mode=0x0000, signal=0x004c, type=1.
[  343.438723] phy40 -> rt2x00lib_rxdone_read_signal: Warning - Frame received with unrecognized signal, mode=0x0000, signal=0x00e6, type=1.

Whereas replugging device make it functional. To solve that problem
force reset device during probe.

With patch messages are gone. Unfortunately device may sometimes
still does not operate correctly after module reload (fail to receive
data after associate), but such cases are rarer than without the patch.

Signed-off-by: Stanislaw Gruszka <stf_xl@wp.pl>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rt2x00: fix possible memory corruption in case of invalid rxdesc.size

Sometimes rxdesc descriptor provided by hardware contains invalid
(random) data. For example rxdesc.size can be bigger than actual
size of the buffer. When this happen rt2x00crypto_rx_insert_iv()
corrupt memory doing memmove outside of buffer boundaries.

Signed-off-by: Stanislaw Gruszka <stf_xl@wp.pl>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

b43: N-PHY: move declarations of chantables functions to correct files

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

b43: N-PHY: update switching analog on/off

Specs were recently updated.

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

b43: HT-PHY: switch radio to requested channel

Switching channel happens after specific SHM write to B43_SHM_SH_CHAN.
This is the way we found it in BCM4331 MMIO dumps. By comparing with
N-PHY code we noticed there is routing used for SYN and TX/RX.

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

b43: HT-PHY: add place for implementing channel switching

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

b43: HT-PHY: define standard structs for channel switching

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

b43: HT-PHY: enable radio

The trick was to find 0x810 PHY reg ops close to analog enabling code.
To find out proper masks and sets, MMIO hacks were used.

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

b43: HT-PHY: implement killing radio

Closed drivers kill radio right after reading radio version and MACCTL,
so it was easy to find related PHY ops:
 phy_read(0x0810) -> 0x0000
phy_write(0x0810) <- 0x0000
To find out the mask of above OP, MMIO hack was used to fake read val:
 phy_read(0x0810) -> 0xffff
phy_write(0x0810) <- 0x0000

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Merge branch 'master' of /linux/kernel/git/padovan/bluetooth-next-2.6

Bluetooth: Fix not setting the chan state

When the connection is ready we should set the connection
to CONNECTED so userspace can use it.

Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@openbossa.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>

Merge /linux/kernel/git/padovan/bluetooth-2.6

Conflicts:
net/bluetooth/l2cap_core.c

rtlwifi: rtl8192{c,ce,cu,se}: Remove comparisons of booleans with true

These are a potential source of confusion, as most C code treats all
non-zero values as true.

Signed-off-by: Mike McCormack <mikem@ring3k.org>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rtlwifi: rtl8192cu: Remove unused parameter

rtl_ps_set_rf_state's protect_or_not parameter is not set to
true anywhere, except for commented out code.

It enables some legacy locking code, which is no longer used,
so delete the parameter and the old locking code.

Signed-off-by: Mike McCormack <mikem@ring3k.org>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rtlwifi: Fix typo in variable name

offchan_deley should be offchan_delay

Signed-off-by: Mike McCormack <mikem@ring3k.org>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

bcma: clean exports of functions

Function managing IRQs is needed for external drivers like b43.
On the other side we do not expect writing any hosts drivers outside of
bcma, so this is safe to do not export functions related to this.

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath5k: add missing ieee80211_free_hw() on unload in AHB code

Signed-off-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath5k: free sc->ah in ath5k_deinit_softc

Nothing else is freeing it, and this mirrors the error handling path
already in ath5k_init_softc.

https://bugzilla.kernel.org/show_bug.cgi?id=37592

Signed-off-by: John W. Linville <linville@tuxdriver.com>
Reported-by: Tsyvarev Andrey <tsyvarev@ispras.ru>

bcma: fix BCM43224 rev 0 workaround

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

bcma: enable support for 14e4:4357 (BCM43225)

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k_hw: make sure PAPRD training is properly done

checking the status of PAPRD_AGC2_POWER(Log(ADC_power) measured after
last gain-change in dB) field suggests whether the PAPRD is completely/properly
done. This is an additional check apart from polling for PAPRD done bit being set.
        Susinder suggests that the ideal power range value should be
0xf0 to 0xfe. With AR9382 we do have the values in this range. to have a
common check for all platforms we take agc2_power should be atleast greater
than 0xe0

Cc: susinder@qca.qualcomm.com
Cc: senthilb@qca.qualcomm.com
Cc: kmuthusa@qca.qualcomm.com
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: Fix a corner case failure in sending PAPRD frames in HT40

when the AP is configured with HT40/2.4GHz and when PAPRD is enabled in station
we have PAPRD training frames never sent out because of the following
failure "PAPRD target power delta out of range". This consistently happens
in channel 10,11 in Over The Air testing and rarely in channel 6 under wired
setup.
        the reason behind this issue is all the HT40 rates target power
are 0 when we operate in channel 10/11 at 2.4GHz

Signed-off-by: Mohammed Shafi Shajakhan <mshajakhan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mac80211: quiesce vif before suspending

Cancel all relevant timers/works before suspending (wowlan).

This patch handles the following warning:
WARNING: at net/mac80211/util.c:565 queueing ieee80211 work while going to suspend
Backtrace:
[<bf07b598>] (ieee80211_can_queue_work+0x0/0x4c [mac80211])
[<bf07c28c>] (ieee80211_queue_work+0x0/0x30 [mac80211])
[<bf0690dc>] (ieee80211_sta_timer+0x0/0x3c [mac80211])
[<c00a3008>] (run_timer_softirq+0x0/0x220)
[<c009e530>] (__do_softirq+0x0/0x130)
[<c009e660>] (irq_exit+0x0/0xb4)
[<c004c4a0>] (ipi_timer+0x0/0x4c)
[<c0046350>] (do_local_timer+0x0/0x88)
[<c00488ec>] (cpu_idle+0x0/0xe0)
[<c05294e8>] (rest_init+0x0/0xe0)
[<c0008958>] (start_kernel+0x0/0x314)

Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Bluetooth: Remove useless access to the socket

We already have access to the chan, we don't have to access the
socket to get its imtu.

Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@openbossa.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>

Bluetooth: Fix crash when setting a LE socket to ready

We should not try to do any other type of configuration for
LE links when they become ready.

Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@openbossa.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>

Merge branch 'wireless-next-2.6' of git://git./linux/kernel/git/iwlwifi/iwlwifi-2.6

rtlwifi: include mac80211.h from core.h

core.h references ieee80211_ops but doesn't include mac80211.h, which issues
a warning once mac80211-compat.h is taken into use.

Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@adurom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

zd1211rw: include mac80211.h from zd_chip.h

zd_chip.h contains one function with a pointer to ieee80211_hw but doesn't
include mac80211.h. As a temporary solution include mac80211.h to avoid
a warning.

Signed-off-by: Kalle Valo <kvalo@adurom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

iwlwifi: fix stop/wake queue hacks

The hacks break once mac80211-compat.h is taken into use. Fix it by adding
an ifdef check.

Signed-off-by: Kalle Valo <kvalo@adurom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

iwlegacy: fix stop/wake queue hacks

The hacks break once mac80211-compat.h is taken into use. Fix it by adding
an ifdef check.

Signed-off-by: Kalle Valo <kvalo@adurom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

iwlagn: remove incorrect define

Remove unused and incorrect EEPROM define

Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>

iwlagn: merge duplicate code into single function

Same operation needed by multiple devices, move to single function.

Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>

iwlagn: code alignment

Code alignment, no functional changes.

Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>

iwlagn: add offset define for subsystem id

Add offset define for subsystem id in EEPROM

Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>