at91: add USB kmods only for subtargets that support USB

Currently, kmod-usb-ohci,kmod-at91-udc and kmod-usb-gadget-eth are included
as the default packages for all at91 subtargets.

However, this is breaking image builder as kmod-at91-udc is not being built
on sama7 since it depends on USB_SUPPORT and sama7 does not have USB support
enabled in the kernel as its not supported upstream so its not even
selectable in the config.

So, move to include these as default packages only for sama5 and sama9x as
both of those have USB support enabled.

Fixes: #18407
Link: https://github.com/openwrt/openwrt/pull/18413
Signed-off-by: Robert Marko <robimarko@gmail.com>

bmips: add support for Actiontec T1200H

Specifications:
- SoC: Broadcom BCM63168 dual 400MHz MIPS
- Flash: 128MB NAND ESMT F59L1G81A
- RAM: 128MB DDR3
- Ethernet: 5x 1000M
- Wifi: BCM435F
- 1x USB 2.0 port
- 2x Button
- 11x LED
- Coax HPNA (unsupported)
- RJ11 xDSL (unsupported)

Install instructions:
The booloader will only install signed firmware so the image has to
be manually flashed.

- Set up a TFTP server on 192.168.1.0/24 to serve the initramfs image
- Interrupt the bootloader and run from RAM with
  r 192.168.1.100:openwrt-bmips-bcm63268-actiontec_t1200h-initramfs.elf
- On the openwrt console, copy the wfi image using wget/tftp/scp, i.e
  scp user@192.168.1.100:~/openwrt/bin/targets/bmips/bcm63268/openwrt-bmips-bcm63268-actiontec_t1200h-squashfs-cfe.bin /tmp/
- Erase half the flash partition where openwrt will be installed with
  flash_erase -j /dev/mtd1 0 491
- Flash the openwrt image with
  nandwrite -p /dev/mtd1 /tmp/openwrt-bmips-bcm63268-actiontec_t1200h-squashfs-cfe.bin
- Reboot
- Interrupt the bootloader again and use the c command to boot from
  previous firmware if vendor image is loaded

Signed-off-by: Kyle Hendry <kylehendrydev@gmail.com>
[Minor improvements to DTS file]
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>

bcm63xx-cfe: update to latest version

actiontec: t1200h: add cferam.000 file

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>

ipq40xx: dts: fix "qcom,coexist-support" property type

Convert the property variable type of "qcom,coexist-support" from
u32 to u8 to match the definition in the dt-bindings document.

Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/18393
Signed-off-by: Robert Marko <robimarko@gmail.com>

ath10k-ct: remove "qcom,coexist-support" property type hack

The ath10k dt-binding property "qcom,coexist-support" was
explicitly defined as type uint8 since upstream commit
ed09c61eb19d ("dt-bindings: net: Convert ath10k to YAML").
Therefore, this hack patch no longer makes sense.

Link: https://github.com/torvalds/linux/commit/ed09c61eb19d9889780c791cb316ac76468f5186
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/18393
Signed-off-by: Robert Marko <robimarko@gmail.com>

octeon: force pcs reset to fix qca833x traffic

There is a known bug with qca833x switches where they fail to pass
traffic without first resetting the PCS. U-Boot already has this fix,
though it uses a much newer networking stack from Marvell. This commit
backports the fix for OpenWrt.

References:
- https://github.com/u-boot/u-boot/blob/master/arch/mips/mach-octeon/cvmx-helper-sgmii.c#L197-L225
- https://github.com/u-boot/u-boot/blob/master/arch/mips/mach-octeon/cvmx-helper-sgmii.c#L701-L737

Signed-off-by: Andrew LaMarche <andrewjlamarche@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/18385
Signed-off-by: Robert Marko <robimarko@gmail.com>

tools/xz: update to 5.8.0

Changelogs:
https://github.com/tukaani-project/xz/releases/tag/v5.8.0

Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/18367
Signed-off-by: Nick Hainke <vincent@systemli.org>

realtek: refactor RTL930x MAC config to fix PHY ports

Currently, network ports using PHYs get a link, but there is no traffic.
Make it work again by moving the MAC config to phylink_mac_link_up.

A similiar change has been previously applied for RTL83xx in commit
cd958d945be0 ("realtek: 6.6: refactor mac config and link up for
RTL83xx").

Fixes: https://github.com/openwrt/openwrt/issues/17010
Signed-off-by: Jan Hoffmann <jan@3e8.eu>
Tested-by: Christoph Krapp <achterin@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/18268
Signed-off-by: Sander Vanheule <sander@svanheule.net>

mac80211: ath11k: Fix DMA buffer allocation to resolve SWIOTLB issues

Backport two commits to resolve issues with ath1kk causing it to fail
driver registration on iommuless systems with DRAM outside of 32bit
addressing such as a 4GiB imx8mm:

commit 1bcd20981834 ("wifi: ath11k: Fix DMA buffer allocation
to resolve SWIOTLB issues")
commit eeadc6baf8b3 ("wifi: ath11k: Use dma_alloc_noncoherent
for rx_tid buffer allocation")

Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Link: https://github.com/openwrt/openwrt/pull/17751
Signed-off-by: Robert Marko <robimarko@gmail.com>

kernel: modules: reenable led-group-multi-color patch

This reverts commit 1375a7bae0d5e8dddb6b6cfe0584a399cd6c20b4.

This version does not activate the CONFIG_LEDS_CLASS_MULTICOLOR option,
this option is controlled by the generic target configuration.

Signed-off-by: jonathan brophy <professor_jonny@hotmail.com>
Link: https://github.com/openwrt/openwrt/pull/17277
[Reword commit message]
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>

stm32: add default kernel config option CONFIG_LEDS_CLASS_MULTICOLOR

The generic target configuration activates the
CONFIG_LEDS_CLASS_MULTICOLOR option. Do not deactivate it for the stm32
target.

Signed-off-by: jonathan brophy <professor_jonny@hotmail.com>
Link: https://github.com/openwrt/openwrt/pull/17277
[Reword commit message]
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>

ath79: move TP-Link RE450 v1 & v2 and RE355 v1 to tiny target

This restores sysupgrade support

Since OpenWrt 23.05, the firmware selector no longer provides sysupgrade
images for RE450 V1 & V2 and RE355 v1 due to image size constraints
(~5.7MB limit), making the generic build unusable.

This commit moves RE450 V1 & V2 to the tiny target, enabling:
- Smaller image builds within the flash size limit.
- Restored sysupgrade support via the firmware selector.
- A secure-by-default wireless setup while allowing full management via UCI.
- Officially supported images, reducing the need for custom (potentially insecure) builds.

This ensures users can install a functional OpenWrt build without compromising security defaults.

Signed-off-by: Ivan Diaz <diaz.it@icloud.com>
[Squashed the commits together and just copied the target definition
from the generic subtarget.]
Link: https://github.com/openwrt/openwrt/pull/18126
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>

ramips: mt76x8: add support for Keenetic Launcher (KN-1221)

Specification:
SoC: MediaTek MT7628AN
RAM: 128M DDR2, ESMT M14D128168A (2Y)
Flash: 32M, cFeon EN25QH256A (Dual Boot on OEM, concatenated on OpenWrt,
SPI)
Switch: MediaTek MT7628AN, 3 ports 100 Mbps
WiFi: MediaTek MT7628AN 2.4 GHz 802.11n
USB: 1 port USB 2.0
GPIO: 1 button (Wi-Fi & Reset on OEM, Reset on OpenWrt), 3 LEDs (Power,
Internet, Wi-Fi), USB port power controls

Disassembly:
There are 2 screws at the bottom near the LEDs hidden by rubber mounts.
After removing the screws, pry the gray plastic part around (it is secured
with latches) and remove it.

UART Interface:
The UART interface can be connected to the 5 pin located between LAN
ports and the WAN one.
Pins (from the second LAN port to the WAN one): VCC, TX, RX, NC, GND
Settings: 115200, 8N1

Flashing via TFTP:
1. Connect your PC and router to the first LAN port, configure PC
interface using IP 192.168.1.2, mask 255.255.255.0
2. Serve the firmware image (for OpenWrt it is *-squashfs-factory.bin)
renamed to KN-1221_recovery.bin via TFTP
3. Power up the router while pressing Wi-Fi button
4. Release Wi-Fi button when Power LED starts blinking

To revert back to OEM firmware:
The return to the OEM firmware is carried out by using the methods
described above with the help of the appropriate firmware image found on
osvault.keenetic.net.

When using OEM bootloader, the firmware image size cannot exceed the size
of one OEM «Firmware_x» partition or Kernel + rootFS size.

Signed-off-by: Ivan Davydov <lotigara@lotigara.ru>
Link: https://github.com/openwrt/openwrt/pull/18164
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>

kernel: bump 6.6 to 6.6.85

Changelog: https://cdn.kernel.org/pub/linux/kernel/v6.x/ChangeLog-6.6.85

Removed upstreamed:
        bcm27xx/patches-6.6/950-1498-dts-bcm2711-PL011-UARTs-are-actually-r1p5.patch[1]
        bcm27xx/patches-6.6/950-1551-drm-v3d-Don-t-run-jobs-that-have-errors-flagged-in-i.patch[2]

Manually rebased:
        bcm27xx/patches-6.6/950-1512-dts-bcm2711-Don-t-mark-timer-regs-unconfigured.patch

All other patches automatically rebased.

1. https://web.git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v6.6.85&id=61820187b3ef5a15aed7ef49ed1fcc13398b449c
2. https://web.git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v6.6.85&id=7cd375d46afcce906cfcddf5aec6b318199d1f16

Build system: x86/64
Build-tested: flogic/xiaomi_redmi-router-ax6000-ubootmod, ramips/tplink_archer-a6-v3, x86/64
Run-tested: flogic/xiaomi_redmi-router-ax6000-ubootmod, ramips/tplink_archer-a6-v3, x86/64

Signed-off-by: John Audia <therealgraysky@proton.me>
Link: https://github.com/openwrt/openwrt/pull/18379
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>

ath10k-ct-firmware: remove QCA9888 board file symbolic link

Although ath10k pre-calibration data and board description file
have similar data structures, they are completely different things.
Therefore, let's remove these incorrect and confusing links.

Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/18069
Signed-off-by: Robert Marko <robimarko@gmail.com>

kernel: Mediatek: fix EEE registers init

After booting, a "transmit queue 0 timed out" warning followed by a
register dump was observed. The dump indicates that mtk_hw_init() does
not initialize the EEECR during probe. This occurs because the
netdev is allocated in mtk_add_mac(), which is called after
mtk_hw_init(). Consequently, the EEECR register remains uninitialized
until a reset is triggered, causing mtk_hw_init() to run again with a
valid netdev, at which point the register is finally set.

To address this, instead of modifying the probe sequence, latch the Tx
LPI enable state and timer value, and move the EEECR register
initialization to mtk_mac_link_up() to ensure proper setup when the
interface comes up.

Additionally, the splat reveals that LPI functionality is controlled by
the MAC_MCR_EEE bits in the MCR register. Update mtk_set_eee() to
modify these bits accordingly.

Fixes: d8315d5358d5 ("kernel: backport Mediatek SoC EEE support")
Fixes: edddbaf79ccf ("kernel: Mediatek: set default EEE Tx LPI timer")
Signed-off-by: Qingfang Deng <dqfext@gmail.com>

ath10k-ct: silence some harmless noisy logs

Users feel anxious about some ath10k driver logs. After further
investigation, in fact these logs are harmless. Only developers
need to care about them in order to optimize some parameters.
Let's just silence them to reduce these similar user reports.

Closes: https://github.com/openwrt/openwrt/issues/13148
Closes: https://github.com/openwrt/openwrt/issues/14422
Closes: https://github.com/openwrt/openwrt/issues/15959
Closes: https://github.com/openwrt/openwrt/issues/15997
Closes: https://github.com/openwrt/openwrt/issues/16896
Closes: https://github.com/openwrt/openwrt/issues/18046
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/18368
Signed-off-by: Robert Marko <robimarko@gmail.com>

ath10k-ct: update to version 6.14

This new version fixes some memory leak and NULL pointer issues.

Upstreamed patches:
[1] 010-api_update.patch
[2] 201-wifi-ath10k-add-LED-and-GPIO-controlling-support-for.patch

The new 003 patch was introduced to fix the build error on old LTS
kernel. The patch 004 was used to fix the issue of IPQ4019 radio
not being able to start.

Tested on QCA9882 and IPQ4019.

[1] https://github.com/torvalds/linux/commit/bca8bc0399ac2efd56e6adbed0307e10125a556c
[2] https://github.com/torvalds/linux/commit/8e1debd82466a3fe711784ab37e6b54e56011267

Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/18368
Signed-off-by: Robert Marko <robimarko@gmail.com>

rampis: revert fix tplink_mr200v1 wan interface

This reverts commit 7aa3dfdbda829c04475cffbd6708f1ff96e4849b.
As the kernel is now fixed with https://github.com/openwrt/openwrt/commit/ecd609f509f29ed1f75db5c7a623f359c64efb72

Signed-off-by: Marius Durbaca <mariusd84@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/18380
Signed-off-by: Robert Marko <robimarko@gmail.com>

mediatek: restrict compat_version override for BPi-R3

Only force compat_version to 1.2 if it was less than 1.2 before, as changes
1.1 and 1.2 were bootloader-related and a completed boot indicates that the
changes have been completed. Newer compat version 1.3 indicates a config change
and should not be forced on boot.

Fixes: 84fc59c0d5 ("mediatek: filogic: bpi-r3: set netdev-name for sfp1 port")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>

kernel: modules: ixgbe,ixgbevf,i40e: remove unused settings and depends

Remove settings and depends that are not used anywhere.

Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Link: https://github.com/openwrt/openwrt/pull/18291
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>

firewall4: update to Git HEAD (2025-03-17)

b6e5157527d3 fw4: fix reading kernel version
42d3b3d4ca21 fw4: allow family any for ipsets not matching IP addresses
edfdfc6df484 Revert "fw4: allow family any for ipsets not matching IP addresses"
97962771aa3c config: drop to-be-forwarded-nowhere packets on wans
00fc6943a297 init: remove unnecessary stop logic
ad3cba79c192 fw4: allow family any for ipsets not matching IP addresses

Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
[fix PKG_MIRROR_HASH]
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/18283
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>

generic: move backport patches 751-03 and 751-04 to pending

Patches 751-03 and 751-04 as a result of commit 6407ef8d2bcb4a0a6284de09cd77bd1868c1d6ea
were incorrectly placed in the backport folder.
So they return to their proper place.

Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Link: https://github.com/openwrt/openwrt/pull/18253
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>

generic: rename backport patch 752-03 to name with correct version

Rename 752-03-v6.6-net-ethernet-mtk_eth_soc-rely-on-mtk_pse_port-defini.patch
to 752-03-v6.7-net-ethernet-mtk_eth_soc-rely-on-mtk_pse_port-defini.patch
because it is used since kernel 6.7 (https://lore.kernel.org/lkml/20231028011741.2400327-1-kuba@kernel.org/).
Link: https://web.git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=linux-6.7.y&id=5c33c09c89789ea45d2aac2471a28c9f90b04c95
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Link: https://github.com/openwrt/openwrt/pull/18253
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>

generic: rename backport patches to names containing version

Rename 770-net-introduce-napi_is_scheduled-helper.patch
to 770-v6.7-net-introduce-napi_is_scheduled-helper.patch
because it is used since kernel 6.7 (https://lore.kernel.org/lkml/20231028011741.2400327-1-kuba@kernel.org/).
Link: https://web.git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=linux-6.7.y&id=7f3eb2174512fe6c9c0f062e96eccb0d3cc6d5cd
Rename 751-01-STABLE-net-ethernet-mediatek-split-tx-and-rx-fields-in-mtk_.patch
to 751-01-v6.8-net-ethernet-mediatek-split-tx-and-rx-fields-in-mtk_.patch
because it is used since kernel 6.8.12 (https://lore.kernel.org/lkml/2024053036-matron-confess-13e0@gregkh/).
Link: https://web.git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=linux-6.8.y&id=b411384df5814fe6fd861d4869607577bcec73a1
Rename 751-02-STABLE-net-ethernet-mediatek-use-QDMA-instead-of-ADMAv2-on-.patch
to 751-02-v6.8-net-ethernet-mediatek-use-QDMA-instead-of-ADMAv2-on-.patch
because it is used since kernel 6.8.12 (https://lore.kernel.org/lkml/2024053036-matron-confess-13e0@gregkh/).
Link: https://web.git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=linux-6.8.y&id=0849f56b5146b70f2da328b1d178d0a3c53d6846
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Link: https://github.com/openwrt/openwrt/pull/18253
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>

uboot-tools: add fit-check-sign package

Add fit-check-sign package which allows validating a uImage.FIT.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>

uboot-tools: dumpimage: get rid of libopenssl dependency

Get rid of of dependency on libopenssl and refresh patches.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>

uboot-tools: rename patches

Sanetize patch name scheme to always use 3 digits prefix.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>

mac80211: fix compilation error for old stable kernel version

Fix compilation error for old stable version caused by
genlmsg_multicast_allns backport fix pushed middle version.

Version 5.15 version 0-169, 6.1 version 0-115, 6.6 version 0-58 have the
old genlmsg_multicast_allns version with flags variable.

Compiling backport project with these version result in a compilation
error. To handle this, introduce a backport function for the affected
kernel version.

Link: https://github.com/openwrt/openwrt/pull/18373
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>

mediatek: filogic: add build for ASUS ZenWiFi BT8 with OpenWrt's U-Boot

Add 'ubootmod' variant for the ASUS ZenWiFi BT8.
An out-of-tree installer will be provided in Github to allow users an easy
transition from the stock loader to OpenWrt's bootchain which is built from
source.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>

uboot-envtools: add support for ASUS ZenWiFi BT8 (ubootmod)

We are using a replacement bootchain on that device, so add default UBI
environment settings.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>

uboot-mediatek: add ASUS ZenWiFi BT8 support

Add U-Boot build for the ASUS ZenWiFi BT8 intended to replace the
stock loader.

Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>

arm-trusted-firmware-mediatek: add MT7988 BL2 DDR4 images

Other than most boards with DDR4 the ASUS ZenWiFi BT8 cannot use the
"comb" DDR calibration option and needs only the "ddr4" option set
instead.

Build TF-A SPIM-NAND with UBI as well as to boot from RAM with
mtk_uartboot for MT7988 with DDR4 RAM.

Signed-off-by: John Crispin <john@phrozen.org>

mediatek: filogic: prepare for ubootmod build of ASUS ZenWiFi BT8

Break out all flash-layout dependent parts from device tree into separate
dtsi file to be used by both, stock layout and upcoming ubootmod variant.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>

mediatek: filogic: add Asus ZenWiFi BT8

Hardware
--------
MediaTek MT7988D SoC (3x Cortex-A73 @1.8 GHz max)
1GB DDR4 RAM
128MB SPI-NAND (Winbond)
MediaTek MT7996 BE14000 Tri-Band Wi-Fi 7
3x LAN (2x 1GE MT7988 built-in, 1x 2.5GE MaxLinear GPY211C)
1x WAN (2.5GE MT7988 built-in)
LED: RGB PWM (supported as 3x PWM LED)
USB: 1x USB 3
Buttons: RESET, WPS
UART: 115200 8N1 3.3V

Installation
------------
1. Hold down RESET button and power on the device until
   LED pulses red.

2. Assign IP 192.168.1.70/24 to your computer's Ethernet port

3. Connect Ethernet to one of the 1GE LAN ports

4. Open browser and visit http://192.168.1.1

5. Upload openwrt-mediatek-filogic-asus_zenwifi-bt8-factory.bin

6. Once OpenWrt initramfs system comes up, do sysupgrade using
   openwrt-mediatek-filogic-asus_zenwifi-bt8-squashfs-sysupgrade.bin

Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>

Revert "tools/libressl: update to 4.0.0"

This reverts commit 21cece29e9eebc397eadee259e60c7fc44828cce.

Unfortunately, LibreSSL 4.0 causes the host APK tools to segfault under
fakeroot when .apk is being generated and it is completely breaking
building under Debian and Ubuntu hosts.

So, until this is fixed lets revert the update.

Signed-off-by: Robert Marko <robimarko@gmail.com>

kernel: move accepted patch from pending-6.6 to backport-6.6

792-igc-enable-HW-vlan-tag-insertion-stripping-by-defaul.patch has been
accepted for Linux 6.16.

Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>

generic: fitblk: close block device if mapping image failed

In case a broken fit image is present on flash the fitblk driver would
not map any /dev/fit* devices, but also not always close the block device
the image resides on. In case of ubiblock devices this is fatal as one
then cannot remove the ubiblock device (-EBUSY), and hence cannot replace
the broken image.
Always close the block device in case no sub-image was mapped.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>

tools/libressl: update to 4.0.0

Stable version. Odd versions are betas.

Added static patch to rename some ecdsa symbols that conflict with
u-boot's mkimage.

These symbols are not exported by default but because OpenWrt uses a
static libressl, they are present and conflict with mkimage's libecdsa.

Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16901
Signed-off-by: Nick Hainke <vincent@systemli.org>

qualcommax: ipq60xx: add Linksys MR7500 support

Codename: Divo

Hardware specification:
========
SoC: Qualcomm IPQ6018
RAM: 512MB (2x ESMT 256MB DDR3L M15T2G16128A–DEBG2R)
NAND Flash: 512MB (Macronix MX30UF4G18AC or SK Hynix H27S4G8F2EDA-BC)
Ethernet: 1x 10/100/1000/2500/5000Mbps (Marvell AQR114C-B0)
Ethernet: 4x 10/100/1000Mbps (Qualcomm QCA8075)
WiFi1: 6GHz ax 4x4@20/40/160 MHz (Qualcomm QCN9024 + Skyworks SKY85784-11) - channels 33-229
WiFi2: 5GHz ax 2x2@20/40/80 MHz (Qualcomm QCN5052 + Skyworks SKY85755-11) - channels 36-177
WiFi3: 2.4GHz ax 2x2@20/40 MHz (Qualcomm QCN5022 + Skyworks SKY8340-11)
IoT: Bluetooth 5 (CSR8811) - not implemented
LED: 1x RGB status + USB Blue (PWM)
USB: 1x USB 3.0
Button: WPS, Reset

Flash instructions (Without Serial):
========
Open Linksys Web UI - http://192.168.1.1/ca or http://linksysxxxxx.lan/ca depending on your setup.
  xxxxx is the last 5 digits from the SN found on a sticker under the device.
Click on the Linksys Logo to by-pass smart app registration.
Login with your admin password. The default password can be found on the same sticker.
To enter into the support mode, click on the “CA” link and the bottom of the page.
Open the “Connectivity” menu and upload the squash-factory image with the “Choose file” button.
Click start. Ignore all the prompts and warnings by click “yes” in all the popups.

Flash instructions (With Serial):
========
1. Installation using serial connection from OEM firmware (default login: root, password: admin):
- fw_printenv -n boot_part
In case of 2:
- flash_erase /dev/mtd13 0 0
- nandwrite -p /dev/mtd13 openwrt-qualcommax-ipq60xx-linksys_mr7500-squashfs-factory.bin
or in case of 1:
- flash_erase /dev/mtd15 0 0
- nandwrite -p /dev/mtd15 openwrt-qualcommax-ipq60xx-linksys_mr7500-squashfs-factory.bin
After first boot install firmware on second partition:
- mtd -r -e kernel -n write openwrt-qualcommax-ipq60xx-linksys_mr7500-squashfs-factory.bin kernel
or:
- mtd -r -e alt_kernel -n write openwrt-qualcommax-ipq60xx-linksys_mr7500-squashfs-factory.bin alt_kernel

2. Installation from initramfs image using USB drive:
Put the initramfs image on the USB drive:
- dd bs=1M if=openwrt-qualcommax-ipq60xx-linksys_mr7500-initramfs-uImage.itb of=/dev/sda
Stop u-boot and run:
- usb start && usbboot $loadaddr 0 && bootm $loadaddr
Write firmware to the flash from initramfs:
- mtd -e kernel -n write openwrt-qualcommax-ipq60xx-linksys_mr7500-squashfs-factory.bin kernel
and:
- mtd -r -e alt_kernel -n write openwrt-qualcommax-ipq60xx-linksys_mr7500-squashfs-factory.bin alt_kernel

3. Back to the OEM firmware:
- mtd -e kernel -n write FW_MR7500_1.1.12.211919_prod.img kernel
and:
- mtd -r -e alt_kernel -n write FW_MR7500_1.1.12.211919_prod.img alt_kernel

4. USB recovery:
Put the initramfs image on the USB:
- dd bs=1M if=openwrt-qualcommax-ipq60xx-linksys_mr7500-initramfs-uImage.itb of=/dev/sda
Set u-boot env:
- fw_setenv bootusb 'usb start && usbboot $loadaddr 0 && bootm $loadaddr'
- fw_setenv bootcmd 'run bootusb; if test $auto_recovery = no; then bootipq; elif test $boot_part = 1; then run bootpart1; else run bootpart2; fi'

AQR firmware:
========
0. Firmware extracting:
To extract the firmware, use unblob (unblob.org)
1. Firmware loading:
To properly load the firmware and initialize AQR PHY, we must use the u-boot aq_load_fw function.
To do this, you need to modify u-boot env:
With USB recovery:
- fw_setenv bootcmd 'aq_load_fw; run bootusb; if test $auto_recovery = no; then bootipq; elif test $boot_part = 1; then run bootpart1; else run bootpart2; fi'
and without:
- fw_setenv bootcmd 'aq_load_fw; if test $auto_recovery = no; then bootipq; elif test $boot_part = 1; then run bootpart1; else run bootpart2; fi'
2. Firmware updating:
Newer firmware (AQR114C.cld) is available in the latest OEM firmware (https://downloads.linksys.com/support/assets/firmware/FW_MR7500_1.1.12.211919_prod.img).
Copy AQR114C.cld to /lib/firmware/marvell

Link: openwrt#17428

Signed-off-by: Weikai Kong <priv@pppig236.com>
Link: https://github.com/openwrt/openwrt/pull/18185
Signed-off-by: Robert Marko <robimarko@gmail.com>

target.mk: Fix features detection for PWM

kmod-leds-pwm depends on @PWM_SUPPORT, instead of adding pwm to the
features env for specific targets, use the existing detection method.

Signed-off-by: Weikai Kong <priv@pppig236.com>
Link: https://github.com/openwrt/openwrt/pull/18185
Signed-off-by: Robert Marko <robimarko@gmail.com>

ipq60xx: define common Linksys MR devices configuration

ipq60xx series MR devices share some common attributes such as LED for
USB port.

Signed-off-by: Weikai Kong <priv@pppig236.com>
Link: https://github.com/openwrt/openwrt/pull/18185
Signed-off-by: Robert Marko <robimarko@gmail.com>

ipq6018-ess: Add dp5-syn node

Linksys MR7500 features 4x QSGMII QCA8075 and 1x USXGMII (1/2.5/5 GbE)

Signed-off-by: Weikai Kong <priv@pppig236.com>
Link: https://github.com/openwrt/openwrt/pull/18185
Signed-off-by: Robert Marko <robimarko@gmail.com>

qca-ssdk: enable AQR for ipq60xx targets

MR7500 features IPQ6018 which is CPPE, however, it also utilizes AQR114CB0 as WAN.
Previously, without this patch, aquantia_phy_api_ops was never called.
Therefore, enable `IN_AQUATIA_PHY` so that AQR PHY gets initialized properly on boot.

[    3.973942] Aquantia AQR114C 90000.mdio-1:08: loading firmware version 'v5.6.5 Cybertan Divo 090221 14:43:44' from 'NVMEM'
[   16.059953] aquantia_phy_api_ops_init[1485]:INFO:qca probe aquantia phy driver succeeded!
[   17.930149] Aquantia AQR114C 90000.mdio-1:08: attached PHY driver (mii_bus:phy_addr=90000.mdio-1:08, irq=POLL)

Signed-off-by: Weikai Kong <priv@pppig236.com>
Link: https://github.com/openwrt/openwrt/pull/18185
Signed-off-by: Robert Marko <robimarko@gmail.com>

tools/isl: update to 0.27

version: 0.27
 date: Sun Sep  1 12:07:24 PM CEST 2024
 changes:
         - improved modulo detection
         - remove all unused local variables from affine expressions
         - minor improvements to coalescing
         - minor improvements to lexicographic optimization
         - improved constraint simplification
         - fix handling of empty piecewise expressions

Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Link: https://github.com/openwrt/openwrt/pull/18249
Signed-off-by: Nick Hainke <vincent@systemli.org>

qualcommax: ipq807x: Create working factory images for EAP620 HD v1 and EAP660 HD v1

Create factory tar for EAP620 HD v1 and EAP660 HD v1 which is accepted by the stock UI.
Fix bug in ipq807x and ipq60xx makefiles so TPLINK_SUPPORT_STRING is handled properly.
Modify tplink-mkimage-2022 script and relevant makefiles to allow spaces in support strings (required for EAP620 HD v1 and EAP660 HD v1).

Installation steps are identical to EAP610-Outdoor:
Web UI method
-------------

Set up the device using the vendor's web UI. After that go to
Management->SSH and enable the "SSH Login" checkbox. Select "Save".
The connect to the machine via SSH:

    ssh -o hostkeyalgorithms=ssh-rsa <ip_of_device>

Disable signature verification:

    cliclientd stopcs

Rename the "-web-ui-factory" image to something less than 63
characters, maintaining the ".bin" suffix.
 * Go to System -> Firmware Update.
 * Under "New Firmware File", click "Browse" and select the image
 * Select "Update" and confirm by clicking "OK".

If the update fails, the web UI should show an error message.
Otherwise, the device should reboot into OpenWRT.

Signed-off-by: Shymon Samsel <ssamsel@umass.edu>
Link: https://github.com/openwrt/openwrt/pull/18340
Signed-off-by: Robert Marko <robimarko@gmail.com>

generic: reorder settings

Move "# CONFIG_NVMEM_LAYOUT_ASCII_ENV is not set" to the correct location.

Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Link: https://github.com/openwrt/openwrt/pull/18335
Signed-off-by: Nick Hainke <vincent@systemli.org>

lldpd: bump to 1.0.19

Changes:
- Support of both Apple Silicon and Intel for macOS package.
- Add cvlan/svlan/tpmr capabilities.
- Disable LLDP in firmware for Intel X7xx cards on FreeBSD.
- Add lldpctl_watch_sync_unblock to liblldpctl.
- Add C++ wrapper for lldpctl.

Fix:
- Fix AppArmor policy for /run/lldpd/lldpd.socket.lock.
- Do not query stats for a down interface on Linux.

```
 # lldpd -vv
lldpd 1.0.19
  Built on 2025-03-24T17:43:44Z

Additional LLDP features:    LLDP-MED, Dot1, Dot3, Custom TLV
Additional protocols:        CDP, FDP, EDP, SONMP
SNMP support:                no
Old kernel support:          no (Linux 2.6.39+)
Privilege separation:        enabled
Privilege separation user:   lldp
Privilege separation group:  lldp
Privilege separation chroot: /var/run/lldp
Configuration directory:     /tmp

C compiler command: C compiler command is not available for reproducible builds
Linker command:     Linker compiler command is not available for reproducible builds
```

Tested on: 24.10.0

Signed-off-by: Paul Donald <newtwen+github@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/18345
Signed-off-by: Nick Hainke <vincent@systemli.org>

mbedtls: update to 3.6.3

This release of Mbed TLS provides the fix for a tls compatibility issue of handling fragmented handshake messages.
This release includes fixes for security issues.

* Potential authentication bypass in TLS handshake (CVE-2025-27810) [1]
* TLS clients may unwittingly skip server authentication (CVE-2025-27809) [2]

[1]: https://mbed-tls.readthedocs.io/en/latest/security-advisories/mbedtls-security-advisory-2025-03-2/
[2]: https://mbed-tls.readthedocs.io/en/latest/security-advisories/mbedtls-security-advisory-2025-03-1/

Full release announcement:
https://github.com/Mbed-TLS/mbedtls/releases/tag/mbedtls-3.6.3

Signed-off-by: Magnus Kroken <mkroken@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/18353
Signed-off-by: Nick Hainke <vincent@systemli.org>

rampis: fix tplink_mr200v1 wan interface

RNDIS interface name change from usb0 to eth1

Signed-off-by: Marius Durbaca <mariusd84@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/18298
Signed-off-by: Robert Marko <robimarko@gmail.com>

kernel: bump 6.6 to 6.6.84

Changelog: https://cdn.kernel.org/pub/linux/kernel/v6.x/ChangeLog-6.6.84

All patches automatically rebased.

Build system: x86/64
Build-tested: flogic/xiaomi_redmi-router-ax6000-ubootmod, x86/64
Run-tested: flogic/xiaomi_redmi-router-ax6000-ubootmod, x86/64

Signed-off-by: John Audia <therealgraysky@proton.me>
Link: https://github.com/openwrt/openwrt/pull/18326
Signed-off-by: Nick Hainke <vincent@systemli.org>

qualcommax: mr7350: switch to ascii-eq-delim-env

Using the pending ascii-eq-delim-env4 driver is a better way to read mac addresses since no
extra config is required

The change is like eacc4d8c9b31ac17df034d2140558bdaaa56c16b, except for using smem for devinfo

thanks to @musashino205 for pointing out the simplification that removes
the extra partition

Signed-off-by: Weikai Kong <priv@pppig236.com>
Link: https://github.com/openwrt/openwrt/pull/18186
Signed-off-by: Robert Marko <robimarko@gmail.com>

iw: backport he operation scan support

With this patch, iw can now scan APs in the 6 GHz band and shows
their operation parameters:
~~~
6 Ghz Operation Information: 0x0103070f06
Primary Channel: 1
Channel Width: 80+80 or 160 MHz
Regulatory Info: 0
Center Frequency Segment 0: 7
Center Frequency Segment 1: 15
Minimum Rate: 6
~~~

Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
Link: https://github.com/openwrt/openwrt/pull/18240
Signed-off-by: Robert Marko <robimarko@gmail.com>

mediatek: filogic: fix device sorting

arcadyan_mozart was incorrectly placed below asus devices

Signed-off-by: Christoph Krapp <achterin@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/18331
Signed-off-by: Robert Marko <robimarko@gmail.com>

qualcommax: ipq807x: Create working factory tar for WAX620 and WAX630.

Create factory tar for WAX620 and WAX630 which is accepted by the stock UI.
Must use 'Boot up Backup Firmware' button on stock upgrade page after install and reboot to swap partitions.

Signed-off-by: Erik Servili <serverror@serverror.com>
Link: https://github.com/openwrt/openwrt/pull/18334
Signed-off-by: Robert Marko <robimarko@gmail.com>

ramips: dts: remove redundant console bootargs

`bootargs = "console=ttyS0,57600";` is already defined on all
ramips target SoCs' dtsi. We don't need to override it with the
same value.

Signed-off-by: Shiji Yang <yangshiji66@qq.com>
Link: https://github.com/openwrt/openwrt/pull/18303
Signed-off-by: Robert Marko <robimarko@gmail.com>

strace: update to 6.14

Release Notes:
- https://github.com/strace/strace/releases/tag/v6.13
- https://github.com/strace/strace/releases/tag/v6.14

Link: https://github.com/openwrt/openwrt/pull/18350
Signed-off-by: Nick Hainke <vincent@systemli.org>

libtracefs: update to 1.8.1

ChangeLog
417c2e3 libtracefs: version 1.8.1
41efd9e libtracefs: Add meson build targets to Makefile
310b796 libtracefs utest: Add better logic to cause missed events
b589e32 libtracefs: Add cpu-map sample to trace mapped buffer
4ede86e libtracefs: Enable mmapped ring buffer
e6737d4 libtracefs: Initialize val in build_filter()
590e452 libtracefs: Close dir in the error path in tracefs_event_systems()
0309a87 libtracefs: Close dir in the error path in tracefs_system_events()
f34fb1f libtracefs: Prevent memory leak in tracefs_dynevent_get_all()
48e906b libtracefs: my_yyinput() should return 0 when no data can be read
5e5b2a7 libtracefs: Prevent memory leak in tracefs_instance_create()
8f2593f libtracefs: Prevent a memory leak in open_cpu_files()
7d77b83 libtracefs: Prevent a memory leak in tracefs_system_events()
7fcd8d2 libtracefs: Prevent a memory leak in add_func_str()
a01d0ba libtracefs: Don't leak socket file descriptor in open_vsock()
efdf7f7 libtracefs: Prevent memory leak in tracefs_event_systems()
2342293 libtracefs: Prevent a memory leak in tracefs_synth_add_end_field()
1c95394 libtracefs: Prevent a memory leak in update_fields()
6b35665 libtracefs: Prevent memory leak in append_filer()
aecc0b7 libtracefs: Call va_end() before exiting tracefs_hist_set_sort_key()
a5e37f7 libtracefs: Add trace-mmap.c to meson build
8f62e96 libtracefs meson: Use SemVer in the build description
e04fa01 meson: Add utest option
fb213a4 libtracefs: Update trace_buffer_meta
04505a0 libtracefs utest: Include libgen.h for basename()
7b4a9c9 libtracefs utest: Define _LARGEFILE64_SOURCE for lseek64() with musl
ba75081 libtracefs utest: Add PATH_MAX if it is not already defined
5f27b7f libtracefs: Update the kbuf for previous read in trace_mmap_load_subbuf()
73ac9c1 libtracefs: Fix tracefs_instance_reset() of triggers
7d15d77 libtracefs meson: build tracefs-mmap by default

Link: https://github.com/openwrt/openwrt/pull/18349
Signed-off-by: Nick Hainke <vincent@systemli.org>

libtraceevent: update to 1.8.4

ChangeLog:
bd47bd5 libtraceevent: 1.8.4
fe0bc49 libtraceevent: Print function pointer address when TEP_EVENT_FL_PRINTRAW is specified
f2224d5 libtraceevent: Have sizeof() parsing handle u8/s8 through u64/s64
5f570de libtraceevent: Print arrays like Linux does
645a883 libtraceevent: 1.8.3
d4c1fb4 libtraceevent: Add meson build targets to Makefile
c3dc220 libtraceevent: Fix a double free in process_op()
021da90 libtraceevent: Do not return a local stack pointer in get_field_str()
340e2e6 libtraceevent: Have unit test fail when any tests fail
c84155f libtraceevent: prevent a memory leak in tep_plugin_add_option()
03551eb libtraceevent: Prevent a memory leak in process_fields()
34ece90 libtraceevent: Close shared object in the error path of load_plugin()
8802f0f libtraceevent: Avoid a simple asprintf case
76a0eb8 libtraceevent: Fix event-parse memory leak in process_cond
5bc98bd libtraceevent: Have single quotes represent characters
ec8e0cc libtraceevent: Fix tests running on big endian arch
60ed6c3 libtraceevent: build: Various fixes for the Meson build of libtraceevent
0351241 libtraceevent utest: Include libgen.h for basename() with musl

Link: https://github.com/openwrt/openwrt/pull/18349
Signed-off-by: Nick Hainke <vincent@systemli.org>

ucode: update to Git HEAD (2025-03-24)

2824982da336 ubus: fix broken uc_ubus_defer()

Signed-off-by: Felix Fietkau <nbd@nbd.name>

mediatek: filogic: bpi-r3-mini: add kmod-eeprom-at24

The bpi-r3-mini has an eeprom onboard. Add the related driver to be
able to access this memory.

Signed-off-by: Martin Schiller <ms@dev.tdt.de>

uboot-tools: dont build tools unconditionally

Currently, both envtools and the rest of U-Boot tools are being built
regardless if the dumpimage package has been selected.

This will fail if only envtools are selected since the rest of tools
require OpenSSL while envtools do not require them.

So, only build tools if dumpimage is selected.

Fixes: 46e376c93514 ("uboot-tools: migrate uboot-envtools to uboot-tools")
Fixes: #18327
Tested-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Link: https://github.com/openwrt/openwrt/pull/18329
Signed-off-by: Robert Marko <robimarko@gmail.com>

uboot-tools: remove uboot-tools definition

This is completely unused and not even registered, so drop it.

Link: https://github.com/openwrt/openwrt/pull/18329
Signed-off-by: Robert Marko <robimarko@gmail.com>

uboot-tools: disable python build to fix build error

Signed-off-by: Felix Fietkau <nbd@nbd.name>

qualcommax: ipq60xx: add GL.iNet GL-AX1800/AXT1800 support

Specifications:
  SoC:     Qualcomm IPQ6000
  RAM:     512 MiB
  Flash:   128 MiB NAND
  ETH:     Qualcomm QCA8075
  WLAN1:   2.4GHz 802.11b/g/n/ax 2x2
  WLAN2:   5GHz 802.11a/n/ac/ax 2x2
  Button:  Reset, Switch
  USB:     1x 3.0
  SD slot: 1 in GL-AXT1800

Install via stock firmware:
  Upload factory.bin in stock firmware's upgrade page,
  do not preserve settings.

Install via uboot web failsafe:
  Push the reset button for 5 seconds, then use broswer
  to access http://192.168.1.1, and upload factory.ubi.

Afterwards upgrade can use sysupgrade image.

Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
Link: https://github.com/openwrt/openwrt/pull/14950
Signed-off-by: Robert Marko <robimarko@gmail.com>

qualcommax: backport cpufreq patch for ipq60xx

Make cpufreq work on different IPQ60xx SoC.
Also rebase ipq6018-cp-cpu.dtsi for mp5496.

Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
Link: https://github.com/openwrt/openwrt/pull/14950
Signed-off-by: Robert Marko <robimarko@gmail.com>

qualcommax: backport sdhci patches for ipq60xx

Refresh device tree, remove the useless sdhc2 aliases.

Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
Link: https://github.com/openwrt/openwrt/pull/14950
Signed-off-by: Robert Marko <robimarko@gmail.com>

qualcommax: backport some upstream dts changes

This is the minimal change for the upcoming patches.
Refresh the device tree of ipq807x at the same time.

Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
Link: https://github.com/openwrt/openwrt/pull/14950
Signed-off-by: Robert Marko <robimarko@gmail.com>

qualcommax: backport unmerged ipq60xx pwm support

Because of the dt-bindings error, these patches have not
been merged yet, and the driver part is fine.

Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
Link: https://github.com/openwrt/openwrt/pull/14950
Signed-off-by: Robert Marko <robimarko@gmail.com>

filogic: move append-gl-metadata to image-commands.mk

This can be used by GL.iNet devices from other target.

Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
Link: https://github.com/openwrt/openwrt/pull/14950
Signed-off-by: Robert Marko <robimarko@gmail.com>

lldpd: add `custom-tlv` handling

Do not verify the format of TLV. Leave that to lldpd.

These lldpd config entries:

config custom-tlv
list ports 'eth0'
option tlv 'replace oui 33,44,55 subtype 254 oui-info 55,55,55,55,55'

config custom-tlv
option tlv 'oui 33,44,44 subtype 232'
list ports 'br-lan'
list ports 'eth0'

config custom-tlv # oui-info truncated
option tlv 'add oui 33,44,33 subtype 66 oui-info 5555555555'

config custom-tlv
option tlv 'add oui 33,44,31 subtype 44'

config custom-tlv # invalid oui
option tlv 'add oui 3322 subtype 79'

config custom-tlv # invalid oui
option tlv 'oui 3312 subtype 74'

Produce the following lldpd.conf content:

configure ports eth0 lldp custom-tlv replace oui 33,44,55 subtype 254 oui-info 55,55,55,55,55
configure ports br-lan,eth0 lldp custom-tlv oui 33,44,44 subtype 232
configure lldp custom-tlv add oui 33,44,33 subtype 66 oui-info 5555555555
configure lldp custom-tlv add oui 33,44,31 subtype 44
configure lldp custom-tlv add oui 3322 subtype 79
configure lldp custom-tlv oui 3312 subtype 74

And lldpd (v1.0.13 on v22) logs the following:

Sat Mar 16 19:11:39 2024 daemon.info lldpd[10916]: custom TLV op replace oui 33:44:55 subtype fe
Sat Mar 16 19:11:39 2024 daemon.info lldpd[10916]: custom TLV op add oui 33:44:44 subtype e8
Sat Mar 16 19:11:39 2024 daemon.info lldpd[10916]: custom TLV op add oui 33:44:33 subtype 42
Sat Mar 16 19:11:39 2024 daemon.info lldpd[10916]: custom TLV op add oui 33:44:33 subtype 42
Sat Mar 16 19:11:39 2024 daemon.info lldpd[10916]: custom TLV op add oui 33:44:31 subtype 2c
Sat Mar 16 19:11:39 2024 daemon.info lldpd[10916]: custom TLV op add oui 33:44:31 subtype 2c
Sat Mar 16 19:11:39 2024 daemon.warn lldpcli[10915]: invalid OUI value '3322'
Sat Mar 16 19:11:39 2024 daemon.info lldpcli[10915]: an error occurred while executing last command
Sat Mar 16 19:11:39 2024 daemon.warn lldpcli[10915]: invalid OUI value '3312'
Sat Mar 16 19:11:39 2024 daemon.info lldpcli[10915]: an error occurred while executing last command
Sat Mar 16 19:11:39 2024 daemon.info lldpcli[10915]: lldpd should resume operations

( The last two TLV are invalid: their oui must be three hex bytes, comma
separated. Only the first hex byte of oui-info 5555555555 is used )

Depends on #14867 and its release version bump

Tested on: 22.03.6

Signed-off-by: Paul Donald <newtwen+github@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/14872
Signed-off-by: Robert Marko <robimarko@gmail.com>

lldpd: get_config_cid_ifaces() -> get_interface_csv()

where csv = comma separated value(s)

Make the function more generic. Can use it for not only 'config'.

Now it can be used to parse interfaces for additional lldpd settings,
e.g. custom-tlv.

Tested on: 22.03.6

Signed-off-by: Paul Donald <newtwen+github@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/14872
Signed-off-by: Robert Marko <robimarko@gmail.com>

uboot-tools: create dumpimage package

Ddd dumpimage package to uboot-tools.
Add patches to fix compile for uboot versions >= 2024.01

Signed-off-by: Scott Mercer <TheRootEd24@gmail.com>

uboot-tools: migrate uboot-envtools to uboot-tools

Generalize and merge uboot-envtools package into uboot-tools package.
Remove existing uboot-envtools package.

Signed-off-by: Scott Mercer <TheRootEd24@gmail.com>

uboot-tools: add stub package skeleton

Add uboot-tools stub package skeleton which will replace uboot-envtools
and also provide target-builds for other U-Boot tools.

Signed-off-by: Scott Mercer <TheRootEd24@gmail.com>

ubox: fix logging to external filesystem

As described in #13873, from 23.05.0 onwards logging to a file on an
external filesystem fails under some conditions.

This occurs because the log initscript had code added to prevent start
logging to an external filesystem on boot, and added a trigger to start
said logging when the external filesystem gets mounted.

The issue is that for filesystems mount with fstab uci, the fstab
scripts runs at START=11, while log runs at START=12, which means the
external filesystem may already be mounted by the time the log initscript
runs. Since the external filesystem is already mounted it does not
trigger a hotplug event to trigger the trigger to start logging. This
combination means the logging never automatically starts when the log
file is on an external filesystem.

We therefore add a check for the presence of a mounted filesystem when
the log file is being sent to an fstab mounted filesystem. If the
filesystem is mounted, we don't skip starting logging during boot.

If the filesystem is not mounted then file logging is not started and
the trigger will start the logging when the filesystem is mounted.

Signed-off-by: Daniel F. Dickinson <dfdpublic@wildtechgarden.ca>
[improved commit message]
Signed-off-by: Daniel Golle <daniel@makrotopia.org>

mediatek: filogic: fix case statement in 01_leds

Remove a stray '|' character from 01_leds which has accidentally
been added.

Reported-by: Chukun Pan <amadeus@jmu.edu.cn>
Fixes: 63d56af6c6 ("mediatek: filogic: migrate Netgate N60 to upstream PHY LED control")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>

kernel: igc: enable HW vlan tag insertion/stripping by default

Add a pending patch [1] in order to do so. This will be moved to the backports
section as soon as we know on which Linux version it will be merged.

[1] https://lore.kernel.org/netdev/20250313093615.8037-1-rsalvaterra@gmail.com/

Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>

mediatek: filogic: PHY LEDs do have an address, gpio-leds don't

Other than GPIO LEDs, PHY LEDs do have an address.

Fix node names such that all gpio-leds do *not* contain an '@' sign and
PHY leds which do have an address also do contain the '@' sign.

This is done to prevent more copy&paste'ry of non-complaint DT
fragments.

Fixes: 7cbe34170e ("mediatek: add support for the GL.iNet GL-MT3000")
Fixes: fe10f97439 ("filogic: add support for GL.iNet GL-MT6000")
Fixes: e8f7597317 ("mediatek: filogic: add support for Cudy RE3000 v1")
Fixes: c9cb6411c1 ("mediatek: add support for Cudy WR3000 v1")
Fixes: 7560af7647 ("mediatek: filogic: migrate ASUS TUF AX6000 to upstream PHY LED control")
Fixes: 25ea7ff393 ("mediatek: filogic: migrate Acer W6/W6d to upstream PHY LED control")
Fixes: d50d51d74e ("mediatek: filogic: migrate Zyxel NWA50AX Pro to upstream PHY LED control")
Fixes: b88de5d507 ("mediatek: filogic: migrate Zyxel EX5700 to upstream PHY LED control")
Fixes: 63d56af6c6 ("mediatek: filogic: migrate Netgate N60 to upstream PHY LED control")
Fixes: fd76a38190 ("mediatek: filogic: migrate SmartRG Bonanza to upstream PHY LED control")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>

Revert "mediatek: rename PHY LEDs to match upstream bindings"

This reverts commit 7103a1554aedbccc16a8beab759fcbd3b9d8e422.
It was merged by accident.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>

mediatek: rename PHY LEDs to match upstream bindings

Kernel docs recommends the following pattern "(^led-[0-9a-f]$|led)"[1].

1. https://elixir.bootlin.com/linux/v6.14-rc6/source/Documentation/devicetree/bindings/leds/leds-gpio.yaml#L24

Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>

kernel: drop Maxlinear PHY LED control hack

All devices have already been migrated to the upstream PHY LED
API. This prevents users from adding new devices using this hack.

Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>

mediatek: filogic: migrate SmartRG Bonanza to upstream PHY LED control

This commit switches the control of the leds connected to the Maxlinear
GPY211C PHY to an upstream solution. There should be no functional changes.

Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>

mediatek: filogic: migrate Netgate N60 to upstream PHY LED control

This commit switches the control of the leds connected to the Maxlinear
GPY211C PHY to an upstream solution. There should be no functional changes.

Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>

mediatek: filogic: migrate Zyxel EX5700 to upstream PHY LED control

This commit switches the control of the leds connected to the Maxlinear
GPY211C PHY to an upstream solution. There should be no functional changes.

Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>

libnl-tiny: update to Git HEAD (2025-03-19)

c0df580adbd4 attr.c: fix nla_reserve size check

Signed-off-by: Felix Fietkau <nbd@nbd.name>

kernel: move accepted patch from pending-6.6 to backport-6.6

742-net-phy-air_en8811h-reset-netdev-rules-when-LED-is-s.patch has been
accepted a while ago as
https://git.kernel.org/torvalds/linux/c/87bfdbbb1992

Signed-off-by: Daniel Golle <daniel@makrotopia.org>

ipq-wifi: fix PKG_MIRROR_HASH after update to 2024-02-17

PKG_MIRROR_HASH is incorrect and the package check is currently failing.

Fixes: 4990ce613b7d ("ipq-wifi: update to 2024-02-17")
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>

rockchip: fix missing ".patch" file extension

Fixes missing .patch file extension in:
- https://github.com/openwrt/openwrt/commit/de9ad11dac094b6074c9b23341acbc28806404ae
- https://github.com/openwrt/openwrt/commit/2e7d060fd1ba6160067df1a2ba303c7c2efe2a7e

Signed-off-by: Tomas Lara <tl849670@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/18281
Signed-off-by: Robert Marko <robimarko@gmail.com>

at91bootstrap: update at91bootstrap v4 targets to v4.0.10

Update AT91Bootstrap v4 capable targets to v4.0.10.

Signed-off-by: Nayab Sayed <nayabbasha.sayed@microchip.com>
Link: https://github.com/openwrt/openwrt/pull/18131
Signed-off-by: Robert Marko <robimarko@gmail.com>

ath79: om2p-v1: fix compatible string

This device uses AR9285, and not AR9280.

Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/18271
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>

ramips: Fix Hongdian H8922 v30 pinctrl default state

According to the MT7620A hardware datasheet, GPIO/14 was originally used for RIN of UARTF, but is now used as the WPS LED.

Corrected pinctrl to ensure it works properly in the future.

Signed-off-by: Coia Prant <coiaprant@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/18278
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>

ath79: support switch LEDs on TL-WR1043ND v2/v3

Add switch LED definitions for TP-Link TL-WR1043ND family, based on data
extracted from ar71xx board file. Update the LED labels to match current
pattern, i.e. drop the "tp-link:" prefix.

Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/12487
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>

ath79: TP-link TL-WR1043ND v2/v3: use fixed-link for AR8327 switch connection

Attaching PHY driver to the switch, while adding LEDs binding causes the
PHY driver to create additional LED instances, handled incorrectly by
the PHY driver, which are non-functional. Use fixed-link to attach the
switch driver, instead of PHY driver, to prevent that.

This has a side effect of not logging switch port up/down events in the kernel
log.

Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/12487
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>

ath79: support switch LEDs on Archer C7 family

Add switch LED definitions for TP-Link Archer C7 v1/2/3 family, based on data
extracted from ar71xx board file. Update the LED labels to match current
pattern, i.e. drop the "tp-link:" prefix.

Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/12487
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>

ath79: TP-link Archer C7v2: use fixed-link for AR8327 switch connection

Attaching PHY driver to the switch, while adding LEDs binding causes the
PHY driver to create additional LED instances, handled incorrectly by
the PHY driver, which are non-functional. Use fixed-link to attach the
switch driver, instead of PHY driver, to prevent that.

This has a side effect of not logging switch port up/down events in the kernel
log.

Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/12487
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>

ath79: support switch LEDs on TL-WDR4300 family

Add switch LED definitions for TP-Link TL-WDR4300 family, based on data
extracted from ar71xx board file. Update the LED labels to match current
pattern, i.e. drop the "tp-link:" prefix.

Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/12487
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>

ath79: TP-link TL-WDR4300: use fixed-link for AR8327 switch connection

Attaching PHY driver to the switch, while adding LEDs binding causes the
PHY driver to create additional LED instances, handled incorrectly by
the PHY driver, which are non-functional. Use fixed-link to attach the
switch driver, instead of PHY driver, to prevent that.

This has a side effect of not logging switch port up/down events in the kernel
log.

Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/12487
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>

kernel: ar8327: support LED device tree bindings

The ar8216 switch driver supports exposing configuration of AR8327 and
AR8337 switch LEDs to the userspace, however it is only configurable
through platform data, causing the devices ported from ar71xx target to
lack the support.
Since there is still a long way to go until we can migrate the target to
qca8k, an interim solution is needed.
Extend ar8327_hw_config_of function to parse a "leds"
subnode, which will populate the missing platform data based on device
tree contents, and restore the existing support for the LEDs.
Standard bindings apply, mapping "reg" property to LED index, with
addition of "qca,led-mode" property, which selects HW (0) or SW (1)
mode, defaulting to HW mode.

Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/12487
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>

kernel: ar8327: fix active-low LED initialization

Switch LEDs configured as active-low remain low instead of high upon
initialization, because in ar8327_leds_init, no distinction is made with
regards to LED pattern based on active_low property - only whether HW
mode is active. Select the proper initial pattern based also on
active_low to fix that.

While at that, simplify the equation ruling pattern selection for
setting brightness, avoiding unnecessary binary XOR operation, not
really valid for 'bool' type.

Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/12487
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>