Daniel Danzberger [Tue, 25 Jun 2019 08:58:25 +0000 (10:58 +0200)]
ramips: mt7621: Add new device AsiaRF AP7621-001
Hardware specs:
SoC: Mediatek MT7621A
CPU: 4x 880Mhz
Cache: 32 KB I-Cache and 32 KB D-Cach
256 KB L2 Cache (shared by Dual-Core)
RAM: DDR3 512MB 16bits BUS
FLASH: 16MB
Switch: Mediatek Gigabit Switch (1 x LAN, 1 x WAN)
USB: 1x 3.0
PCI: 3x Mini PCIe
GPS: Quectel L70B
BTN: Reset
LED: - Power
- Ethernet
- Wifi
- USB
UART: UART is present as Pads with throughholes on the PCB.
They are located on left side.
3.3V - RX - GND - TX / 57600-8N1
3.3V is the square pad
Installation:
The stock image is a modified openwrt and can be overflashed via
# sysupgrade -F image.bin
Signed-off-by: Daniel Danzberger <daniel@dd-wrt.com>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
[removed unused label, formatting]
Christian Lamparter [Tue, 25 Jun 2019 12:47:02 +0000 (14:47 +0200)]
ath79: fix "spi-gpio: convert deprecated binding"
This patch fixes the previous commit that rendered the
devices (mostly leds) useless.
Fixes: 1fa24de8c29b ("ath79: spi-gpio: convert deprecated binding")
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Jonas Gorski [Sat, 22 Jun 2019 12:02:27 +0000 (14:02 +0200)]
build: warn when packages have no associated install section
Declaring a package without the appropriate install section is an easy
mistake to make, especially when renaming packages. Since this is also
easy to detect, warn about it when it happens.
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
No-objections-at-all-by: Jo-Philipp Wich <jo@mein.io>
Felix Fietkau [Fri, 7 Jun 2019 17:07:14 +0000 (19:07 +0200)]
mt76: update to the latest version, adds preliminary mt7615 support
b3a2965 mt76x02: fix crash on device reset
ffddb68 mt76x02u: check chip version on probe
7fc5f92 mt76x2u: remove duplicated entry in mt76x2u_device_table
61311d9 mt76: introduce mt76_free_device routine
a7dfcf2 mt76: move mac_work in mt76_dev
334b4ce mt76: add mac80211 driver for MT7615 PCIe-based chipsets
edb2a00 mt76: add unlikely() for dma_mapping_error() check
355c079 mt76: use macro for sn and seq_ctrl conversion
133bffb add firmware for MT7615E
49d9c1b mt76: usb: reduce locking in mt76u_tx_tasklet
3e371ca mt76: set txwi_size according to the driver value
5007326 mt76: add skb pointer to mt76_tx_info
c47a568 mt76: dma: introduce skb field in mt76_txwi_cache
9029560 mt76: dma: add skb check for dummy pointer
e9eea39 mt76: mt7615: use sizeof instead of sizeof_field
98c5359 Revert "mt76: fix potential deadlock on cancelling workqueues"
bc9baa7 mt76x02u: remove bogus stop on suspend
6c1cab9 mt76usb: fix tx/rx stop
0e674c5 mt76x02: remove bogus mutex usage
59f7bb6 Revert "mt76: mt76x02: send no-skb tx status without holding the status lock"
b0f2a30 mt76x02: avoid status_list.lock and sta->rate_ctrl_lock dependency
62054de mt76: mt7603: remove query from mt7603_mcu_msg_send signature
e79d96a mt76: mt7603: use standard signature for mt7603_mcu_msg_send
be8f039 mt76: mt7603: initialize mt76_mcu_ops data structure
9a9c656 mt76: introduce mt76_mcu_restart macro
980b91e mt76: mt7603: init mcu_restart function pointer
a97db3f mt76: mt7603: run __mt76_mcu_send_msg in mt7603_mcu_send_firmware
151115f mt76: mt76x02: mt76x02_poll_tx() can be static
7391f98 mt76: fix endianness sparse warnings
6c06f73 mt76: mt7603: report firmware version using ethtool
f06647e mt76: usb: use EP max packet aligned buffer sizes for rx
f43fccf mt76: move beacon_int in mt76_dev
74ab2cf mt76: move beacon_mask in mt76_dev
23c2f94 mt76: add TX/RX antenna pattern capabilities
6e790e1 mt76: move pre_tbtt_tasklet in mt76_dev
7606c08 mt76: mt7603: enable/disable pre_tbtt_tasklet in mt7603_set_channel
ff22eee mt76: do not enable/disable pre_tbtt_tasklet in scan_start/scan_complete
3157385 mt76: mt7603: dynamically alloc mcu req in mt7603_mcu_set_eeprom
cc674e2 mt76: mt76x02: remove useless return in mt76x02_resync_beacon_timer
6b18427 mt76: move tx_napi in mt76_dev
bce63c4 mt76: mt7603: use napi polling for tx cleanup
4afd89e mt76: mt7615: use napi polling for tx cleanup
2cb4683 mt76: move netif_napi_del in mt76_dma_cleanup
b4ceb9f mt76: Fix a signedness bug in mt7615_add_interface()
d00dc95 mt76: mt7615: Use after free in mt7615_mcu_set_bcn()
4e0ccc6 mt76: mt7615: Make mt7615_irq_handler static
0fd552a mt7615: mcu: simplify __mt7615_mcu_set_wtbl
50f7094 mt7615: mcu: simplify __mt7615_mcu_set_sta_rec
4434d04 mt7615: mcu: remove bss_info_convert_vif_type routine
083fbb9 mt7615: mcu: use proper msg size in mt7615_mcu_add_wtbl_bmc
f61ca80 mt7615: mcu: use proper msg size in mt7615_mcu_add_wtbl
35bd12d mt7615: mcu: unify mt7615_mcu_add_wtbl_bmc and mt7615_mcu_del_wtbl_bmc
f8f990b mt7615: mcu: remove unused parameter in mt7615_mcu_del_wtbl
965bca1 mt7615: remove query from mt7615_mcu_msg_send signature
9b9ca18 mt7615: remove dest from mt7615_mcu_msg_send signature
935b7e5 mt7615: mcu: remove skb_ret from mt7615_mcu_msg_send
2442db4 mt7615: mcu: unify __mt7615_mcu_set_dev_info and mt7615_mcu_set_dev_info
645bc45 mt7615: mcu: do not use function pointers whenever possible
40c4201 mt7615: mcu: remove unused structure in mcu.h
a8834a2 mt7615: mcu: use standard signature for mt7615_mcu_msg_send
824d25c mt7615: initialize mt76_mcu_ops data structure
d943427 mt7615: mcu: init mcu_restart function pointer
c2211e4 mt7615: mcu: run __mt76_mcu_send_msg in mt7615_mcu_send_firmware
cb63a06 mt76: mt7603: stop mac80211 queues before setting the channel
c6aaa3a mt76: mt7615: rearrange cleanup operations in mt7615_unregister_device
97609f3 mt76: mt7615: add static qualifier to mt7615_rx_poll_complete
f9dadd2 mt76: mt7603: add debugfs knob to enable/disable edcca
89cda5d mt7603: fix reading target tx power from eeprom
77d0e33 mt76: fix setting chan->max_power
f575da2 mt76: mt76x02: fix tx status reporting issues
a5d18dc mt76: mt76x02: fix tx reordering on rate control probing without a-mpdu
bd32a93 mt76: mt76x02: remove enable from mt76x02_edcca_init signature
18386ee mt76: mt76x2u: remove mt76x02_edcca_init in mt76x2u_set_channel
da3514f mt76: mt76x2: move mutex_lock inside mt76x2_set_channel
0d4719c mt76: mt76x02: run mt76x02_edcca_init atomically in mt76_edcca_set
fd5af73 mt76: mt76x02: fix edcca file permission
a0f51f2 mt76: mt7615: do not process rx packets if the device is not initialized
753cdee mt76: mt7615: stop mcu first in mt7615_unregister_device
899efe7 mt76: move mt76_insert_ccmp_hdr in mt76-module
6960b6e mt76: mt7615: add support for mtd eeprom parsing
4bcb057 mt76: mt7615: select wifi band according to eeprom
866f2c6 mt76: generalize mt76_get_txpower for 4x4:4 devices
514fb04 mt76: mt7615: add the capability to configure tx power
ced9d43 mt76: mt7615: init get_txpower mac80211 callback
8abd502 mt76: mt7615: rearrange locking in mt7615_config
5b9b62e mt76: move mt76_get_rate in mt76-module
661c7c8 mt76: Remove set but not used variables 'pid' and 'final_mpdu'
f072c7b mt76: mt7615: enable support for mesh
28d9496 mt76: mt7615: fix slow performance when enable encryption
827b9ad mt76: mt7615: remove unused variable in mt7615_mcu_set_bcn
34eea14 mt76: mt7615: remove key check in mt7615_mcu_set_wtbl_key
2bfae5a mt76: usb: fix rx A-MSDU support
b033532 mt76: usb: do not always copy the first part of received frames
3e7fc15 mt76x02: fix reporting of non-probing frames with tx status requested
0d5caea Revert "mt76: usb: do not always copy the first part of received frames"
335e8c6 Revert "mt76: usb: fix rx A-MSDU support"
47ddf4b mt76: revert support for TX_NEEDS_ALIGNED4_SKBS
0b6520b mt7603: rework and fix tx status reporting
539b679 mt7603: improve hardware rate switching configuration
d86d6ef mt76x0: fix RF frontend initialization for external PA
f476a14 mt76x02: fix endian issue in tx status reporting patch
f8d0517 mt76: mt7615: simplify mt7615_mcu_set_sta_rec routine
73ff45f mt76: mt7615: add support for per-chain signal strength reporting
9b67ae6 mt76: mt7615: init per-channel target power
160fdc0 mt76: mt7615: take into account extPA when configuring tx power
2211d93 mt76: mt76x02u: fix sparse warnings: should it be static?
3750533 mt76: mt7615: fix incorrect settings in mesh mode
c37c1ca mt76: mt7615: update peer's bssid when state transition occurs
9dd1089 mt76: mt76u: reduce rx memory footprint
0789f45 mt76: mt7615: remove cfg80211_chan_def from mt7615_set_channel signature
2dca431 mt76: move nl80211_dfs_regions in mt76_dev data structure
3386ccf mt76: mt76u: get rid of {out,in}_max_packet
d680ab0 mt76: usb: fix rx A-MSDU support
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Felix Fietkau [Fri, 7 Jun 2019 17:10:25 +0000 (19:10 +0200)]
mac80211: add rate control support for 4 spatial streams, improve precision
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Adrian Schmutzler [Fri, 21 Jun 2019 23:53:57 +0000 (01:53 +0200)]
ath79: Code style improvements in 10_fix_wifi_mac
This fixes one comparison and several useless echos.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Eneas U de Queiroz [Mon, 24 Jun 2019 19:24:00 +0000 (16:24 -0300)]
ustream-ssl: update to 2019-06-24
This adds chacha20-poly1305 support to the mbedtls variant.
Signed-off-by: Eneas U de Queiroz <cotequeiroz@gmail.com>
Chris Blake [Mon, 24 Jun 2019 11:32:45 +0000 (06:32 -0500)]
mpc85xx: Use uncompressed kernel on the HiveAP-330
It seems that newer builds of OpenWRT have a gzip kernel
larger than 2MB~, which for some reason fails to boot on this board.
However, we have 8MB of kernel space and currently the uncompressed
kernel is 6.5MB~, so we have some space to grow until a better
solution is worked out.
Before:
## Booting kernel from Legacy Image at
ee840000 ...
Image Name: Linux-4.19.53
Created: 2019-06-22 11:17:48 UTC
Image Type: PowerPC Linux Kernel Image (gzip compressed)
Data Size:
2315724 Bytes = 2.2 MB
Load Address:
00000000
Entry Point:
00000000
Verifying Checksum ... OK
## Loading init Ramdisk from Legacy Image at
02000000 ...
Image Name: OpenWrt fake ramdisk
Created: 2019-06-22 11:17:48 UTC
Image Type: PowerPC Linux RAMDisk Image (uncompressed)
Data Size: 0 Bytes = 0 kB
Load Address:
00000000
Entry Point:
00000000
Verifying Checksum ... OK
## Flattened Device Tree blob at
ec000000
Booting using the fdt blob at 0xec000000
Uncompressing Kernel Image ... Error: Bad gzipped data
GUNZIP: uncompress, out-of-mem or overwrite error -
must RESET board to recover
Loading Ramdisk to
10000000, end
10000000 ... OK
Loading Device Tree to
00ffa000, end
00fffc78 ... OK
ft_fixup_l2cache: FDT_ERR_NOTFOUND
After:
## Booting kernel from Legacy Image at
ee840000 ...
Image Name: POWERPC OpenWrt Linux-4.19.53
Created: 2019-06-22 11:17:48 UTC
Image Type: PowerPC Linux Kernel Image (uncompressed)
Data Size:
6724584 Bytes = 6.4 MB
Load Address:
00000000
Entry Point:
00000000
Verifying Checksum ... OK
## Loading init Ramdisk from Legacy Image at
02000000 ...
Image Name: OpenWrt fake ramdisk
Created: 2019-06-22 11:17:48 UTC
Image Type: PowerPC Linux RAMDisk Image (uncompressed)
Data Size: 0 Bytes = 0 kB
Load Address:
00000000
Entry Point:
00000000
Verifying Checksum ... OK
## Flattened Device Tree blob at
ec000000
Booting using the fdt blob at 0xec000000
Loading Kernel Image ... OK
OK
Loading Ramdisk to
10000000, end
10000000 ... OK
Loading Device Tree to
00ffa000, end
00fffc78 ... OK
Signed-off-by: Chris Blake <chrisrblake93@gmail.com>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com> [75 cpl limit]
Christian Lamparter [Sun, 23 Jun 2019 10:02:04 +0000 (12:02 +0200)]
apm821xx: move to 4.19 kernels
The 4.19 code has been available for some time now.
Since the f2fs / loop issue has been under control
I think it's time the target gets to move to it.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Christian Lamparter [Sat, 22 Jun 2019 14:17:58 +0000 (16:17 +0200)]
apm821xx: switch out kernel's CRC32 method
This patch replaces the OpenWrt' favoured
CRC32 Sarwate algorithm with the kernel
recommended SLICE8 CRC32 version.
This change alone lifted btrfs writes from 40 MiB/s
to 54 MiB/s on my My Book Live (SLICE4 managed 48 MiB/s).
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Andrew Cameron [Tue, 15 Jan 2019 02:14:54 +0000 (20:14 -0600)]
ath79: add support for TP-Link CPE610-v1
TP-Link CPE610-v1 is an outdoor wireless CPE for 5 GHz with
one Ethernet port based on Atheros AR9344
Specifications:
- Based on the same underlying hardware as the TP-Link CPE510
- Power, LAN, WLAN5G green LEDs
- 23dBi high-gain directional 2×2 MIMO antenna and a dedicated metal reflector
Flashing instructions:
Flash factory image through stock firmware WEB UI
or through TFTP
To get to TFTP recovery just hold reset button while powering on for
around 4-5 seconds and release.
Rename factory image to recovery.bin
Stock TFTP server IP:192.168.0.100
Stock device TFTP adress:192.168.0.254
Signed-off-by: Andrew Cameron <apcameron@softhome.net>
Joseph Tingiris [Sun, 13 Jan 2019 21:43:50 +0000 (16:43 -0500)]
rssileds: change rssileds.init STOP index
This patch is in a series to allow additional STOP indexes after
umount, so that other block devices may stop cleanly.
rssileds.init is now STOP=89
Signed-off-by: Joseph Tingiris <joseph.tingiris@gmail.com>
Joseph Tingiris [Sun, 13 Jan 2019 21:43:49 +0000 (16:43 -0500)]
kexec-tools: change kdump.init STOP index
This patch is in a series to allow additional STOP indexes after umount,
so that other block devices may stop cleanly.
kdumpinit is now STOP=90
Signed-off-by: Joseph Tingiris <joseph.tingiris@gmail.com>
Joseph Tingiris [Sun, 13 Jan 2019 21:43:48 +0000 (16:43 -0500)]
base-files: change boot & umount STOP indexes
This patch is in a series to allow additional STOP indexes after umount,
so that other block devices may stop cleanly.
boot is now STOP=90
umount is now STOP=90
After this patch series, the resulting STOP indexes in the 80s & 90s
will be:
STOP=85 odhcpd.init
STOP=89 conntrackd.init
STOP=89 log.init
STOP=89 rssileds.init
STOP=90 boot
STOP=90 kdump.init
STOP=90 network
STOP=90 sysfixtime
STOP=90 umount
STOP=98 mdadm.init (note: will be addressed in a separate patch)
Signed-off-by: Joseph Tingiris <joseph.tingiris@gmail.com>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
[PKG_RELEASE is now 200]
Josef Schlehofer [Tue, 18 Jun 2019 22:31:03 +0000 (00:31 +0200)]
mbedtls: Update to version 2.16.2
Signed-off-by: Josef Schlehofer <josef.schlehofer@nic.cz>
Christian Lamparter [Sat, 22 Jun 2019 15:28:06 +0000 (17:28 +0200)]
ath79: spi-gpio: convert deprecated binding
The old gpio-{sck,miso and mosi} binding is
deprecated in favour of {sck,miso and mosi}-gpios.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Christian Lamparter [Sat, 22 Jun 2019 14:56:59 +0000 (16:56 +0200)]
ipq40xx: spi-gpio: convert deprecated binding
The old gpio-{sck,miso and mosi} binding is
deprecated in favour of {sck,miso and mosi}-gpios.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Adrian Schmutzler [Thu, 20 Jun 2019 20:58:02 +0000 (22:58 +0200)]
ath79: Remove redundant LED GPIO definitions for Archer C25 v1
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
HsiuWen Yen [Thu, 20 Jun 2019 16:44:42 +0000 (00:44 +0800)]
netfilter: fix crash in flow offload by adding netns support
Commit
fcb41decf6c6 ("config: enable some useful features on
!SMALL_FLASH devices") enabled netns, which in turn lead to the crash in
the flow offload target.
When the flow offloading framework intends to delete a flow from the
hardware table, it is necessary to retrieve the namespace from
nf_flowtable->ft_net. However, no one ever wrote the namespace into
nf_flowtable->ft_net in advance. So the framework will mistakenly use a
NULL namespace to execute dev_get_by_index_rcu(net, ifindex), leading to
the kernel panic.
Ref: FS#2321
Fixes: fcb41decf6c6 ("config: enable some useful features on !SMALL_FLASH devices")
Tested-by: Simon Tretter <simon@mediaarchitectu.re>
Signed-off-by: HsiuWen Yen <y.hsiuwen@gmail.com>
[merged patch into offload patch, fix for 4.19, SOB fix, commit subj/msg touches]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Koen Vandeputte [Mon, 24 Jun 2019 13:26:44 +0000 (15:26 +0200)]
cns3xxx: switch to kernel 4.19
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Koen Vandeputte [Mon, 24 Jun 2019 11:39:12 +0000 (13:39 +0200)]
kernel: bump 4.19 to 4.19.55
Refreshed all patches.
Compile-tested on: imx6
Runtime-tested on: imx6
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Koen Vandeputte [Mon, 24 Jun 2019 11:38:47 +0000 (13:38 +0200)]
kernel: bump 4.14 to 4.14.129
Refreshed all patches.
Compile-tested on: cns3xxx
Runtime-tested on: cns3xxx
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Koen Vandeputte [Mon, 24 Jun 2019 11:35:40 +0000 (13:35 +0200)]
kernel: bump 4.9 to 4.9.183
Refreshed all patches.
Compile-tested on: none
Runtime-tested on: none
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Christian Lamparter [Sat, 22 Jun 2019 10:23:10 +0000 (12:23 +0200)]
linux-firmware: update to
20190618
Update linux-firmware to
20190618.
git log --pretty=oneline --abbrev-commit
20190416..
20190618
acb56f2 cavium: Add firmware for CNN55XX crypto driver.
a03f1a0 linux-firmware: Update firmware file for Intel Bluetooth 22161
abb7cb6 linux-firmware: Update firmware file for Intel Bluetooth 9560
1e8253b linux-firmware: Update firmware file for Intel Bluetooth 9260
c436aaf linux-firmware: Update AMD SEV firmware
6ae3652 linux-firmware: update licence text for Marvell firmware
1884732 linux-firmware: update firmware for mhdp8546
87b35ca linux-firmware: rsi: update firmware images for Redpine 9113 chipset
55edf52 imx: sdma: update firmware to v3.5/v4.5
93d56c0 nvidia: update GP10[2467] SEC2 RTOS with the one already used on GP108
1f8ebdf linux-firmware: Update firmware file for Intel Bluetooth 8265
bccb385 linux-firmware: Update firmware file for Intel Bluetooth 9260
29a536a linux-firmware: Update firmware file for Intel Bluetooth 9560
cedd500 linux-firmware: Update firmware file for Intel Bluetooth 22161
e04cc56 amlogic: add video decoder firmwares
95a9353 iwlwifi: update -46 firmwares for 22260 and 9000 series
68040ce iwlwifi: add firmware for 22260 and update 9000 series -46 firmwares
fdfb153 iwlwifi: add -46.ucode firmwares for 9000 series
92e17d0 amdgpu: update vega20 to the latest 19.10 firmware
7536c3b amdgpu: update vega12 to the latest 19.10 firmware
2579167 amdgpu: update vega10 to the latest 19.10 firmware
4ea5c73 amdgpu: update polaris11 to the latest 19.10 firmware
4475802 amdgpu: update polaris10 to the latest 19.10 firmware
f9551dc amdgpu: update raven2 to the latest 19.10 firmware
9eaa40d amdgpu: update raven to the latest 19.10 firmware
3c1ab75 amdgpu: update picasso to the latest 19.10 firmware
8e3e08c linux-firmware: update fw for qat devices
cdef971 Mellanox: Add new mlxsw_spectrum firmware 13.2000.1122
13d6bc8 drm/i915/firmware: Add ICL HuC v8.4.3238
1dbb095 drm/i915/firmware: Add ICL GuC v32.0.3
77b6b40 drm/i915/firmware: Add GLK HuC v03.01.2893
f8521cc drm/i915/firmware: Add GLK GuC v32.0.3
9fb9526 drm/i915/firmware: Add KBL GuC v32.0.3
3fbec60 drm/i915/firmware: Add SKL GuC v32.0.3
c7e32a1 drm/i915/firmware: Add BXT GuC v32.0.3
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Christian Lamparter [Fri, 21 Jun 2019 17:21:30 +0000 (19:21 +0200)]
kernel: add promising "fix loop discard errors" hack
This patch adds a promising upstream patch that claims
to help for the treated I/O errors happening on f2fs
or ext4 on real block devices.
|print_req_error: I/O error, dev loop1, sector 1334
Link: <https://patchwork.kernel.org/cover/
10931787/>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Stefan Lippers-Hollmann [Sun, 26 May 2019 03:28:53 +0000 (05:28 +0200)]
kernel: alx driver for AR816x/AR817x Ethernet
These ethernet cards can be found onboard various x86 and
x86_64 Gigabyte mainboards since the sandy-bridge/ ivy-bridge era.
This driver supports the following QCA/"Killer" ethernet cards:
1969:1091 - AR8161 Gigabit Ethernet
1969:1090 - AR8162 Fast Ethernet
1969:10A1 - AR8171 Gigabit Ethernet
1969:10A0 - AR8172 Fast Ethernet
1969:E091 - Killer E2200 Gigabit Ethernet
1969:E0A1 - Killer E2400 Gigabit Ethernet
1969:E0B1 - Killer E2500 Gigabit Ethernet
Successfully runtime tested with the onboard ethernet card of a
Gigabyte GA-H77M-D3H ivy-bridge mainboard (x86_64/EFI image):
02:00.0 Ethernet controller [0200]: Qualcomm Atheros AR8161 [...]
Subsystem: Gigabyte Technology Co., Ltd AR8161 [...]
Kernel driver in use: alx
Kernel modules: alx
alx 0000:02:00.0 eth0: Qualcomm Atheros AR816x/AR817x Ethernet [...]
alx 0000:02:00.0 eth0: NIC Up: 1 Gbps Full
Signed-off-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com> [fix typo,
shorten subject to <50 characters, shorten lines to <76 chars.]
Christian Lamparter [Sun, 16 Jun 2019 11:36:54 +0000 (13:36 +0200)]
toolchain: musl: switch to https instead of git
Daniel Engberg requested switching over to https transport
since he seems to be stuck behind a corporate firewall that
does all the wrong things.
Rick Felker noted that this is "experimental and might break".
<https://www.openwall.com/lists/musl/2019/03/27/1>.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Stefan Lippers-Hollmann [Sat, 15 Jun 2019 04:35:06 +0000 (06:35 +0200)]
mac80211: update WDS/4addr fix to the version accepted upstream
This updates "{nl,mac}80211: allow 4addr AP operation on crypto
controlled devices" to the version (v3), which was accepted into
upstream mac80211.git and which is tagged for -stable backporting
(v4.18+).
https://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211.git/commit/?id=
33d915d9e8ce811d8958915ccd18d71a66c7c495
Signed-off-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
[format-patch]
Christian Lamparter [Thu, 20 Jun 2019 19:46:55 +0000 (21:46 +0200)]
kernel: fix kmod-tpm 4.19 dependencies
This patch fixes the ath79-nand build error:
|Package kmod-tpm is missing dependencies for the following libraries:
|rng-core.ko
by making it depend on rng-core from 4.19 onwards.
This should work as 4.9 is gone so only 4.14 and 4.19
are there.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Deng Qingfang [Fri, 21 Jun 2019 03:10:36 +0000 (11:10 +0800)]
package/network: add PKGARCH:=all to non-binary packages
Packages such as xfrm contain only script files, add PKGARCH:=all
Signed-off-by: Deng Qingfang <dengqf6@mail2.sysu.edu.cn>
Eneas U de Queiroz [Sat, 22 Jun 2019 08:17:21 +0000 (10:17 +0200)]
nghttp2: deduplicate files in staging_dir
'
38b22b1e: deduplicate files in libnghttp2' missed duplicates in
staging_dir by Build/InstallDev.
Signed-off-by: Eneas U de Queiroz <cote2004-github@yahoo.com>
Daniel Engberg [Sat, 15 Jun 2019 02:26:56 +0000 (02:26 +0000)]
tools/bison: Update to 3.4.1
Update bison to 3.4.1
Remove 010-intl-stub-compat.patch
Signed-off-by: Daniel Engberg <daniel.engberg.lists@pyret.net>
Jo-Philipp Wich [Fri, 21 Jun 2019 15:41:28 +0000 (17:41 +0200)]
rpcd: add direct dependency on libjson-c
The OpenWrt buildroot ABI version rebuild tracker does not handle
transient dependencies, therefor add all libraries linked by rpcd
as direct dependencies to the corresponding binary package definition.
This ensures that rpcd is automatically rebuilt and relinked if any
of these libraries has its ABI_VERSION updated in the future.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Petr Štetiar [Tue, 18 Jun 2019 21:45:37 +0000 (21:45 +0000)]
build: fix kernel_*config targets on 4.19
Recent kernel versions need toolchain in order to properly configure
kernel, for example to set CC_HAS_ASM_GOTO config symbol, so missing
toolchain leads to the following error while running `make
kernel_oldconfig` on ath79 target with 4.19 kernel in the clean tree:
init/Kconfig:17: syntax error
init/Kconfig:16: invalid option
./scripts/clang-version.sh: line 15: mips-openwrt-linux-musl-gcc: command not found
./scripts/gcc-plugin.sh: line 11: mips-openwrt-linux-musl-gcc: command not found
net/sched/Kconfig:44: warning: menuconfig statement without prompt
make[4]: *** [scripts/kconfig/Makefile:69: oldconfig] Error 1
So in order to support this new kernel versions, this patch adds
toolchain as a hard dependency to the kernel_*config targets.
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Karel Kočí [Wed, 5 Jun 2019 11:18:41 +0000 (13:18 +0200)]
fstools: block-mount: fix restart of fstab service
Restarting service causes file-systems to be unmounted without being
mounted back. When this service was obsoleted it should have been
implemented in a way that all actions are ignored. Up to this commit
default handler was called when restart was requested. This default
handler just simply calls stop and start. That means that stop called
unmount but start just printed that this service is obsoleted.
This instead implements restart that just prints same message like start
does. It just calls start in reality. This makes restart unavailable for
call.
Signed-off-by: Karel Kočí <karel.koci@nic.cz>
Jo-Philipp Wich [Thu, 20 Jun 2019 19:02:06 +0000 (21:02 +0200)]
metadata: handle ABI version rebuild tracking for transient dependencies
Extend the packageauxvars database to keep a list of possible package
dependencies for each provider, then utilize this information in buildroot
to resolve the ABI version dependencies of dependent packages up to five
levels deep.
This should properly trigger rebuilds for packages indirectly depending
on other packages whose ABI_VERSION changed.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Yousong Zhou [Thu, 20 Jun 2019 10:29:53 +0000 (10:29 +0000)]
base-files: apply new sysctl.conf at postinst
This is mainly for kmod-br-netfilter. To turn off
bridge-netfilter-call-xxx immediately after installation
While at it
- Define filelist="/usr/lib/opkg/info/${pkgname}.list"
- Reuse "[ -z "$root" ]"
- Grep with "-m1"
Fixes FS#2300
Reported-by: Marco Sartorius <tidbits@ormoorgmen.info>
Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
Kevin Darbyshire-Bryant [Wed, 19 Jun 2019 19:25:43 +0000 (20:25 +0100)]
iproute2: update ctinfo support
Follow upstream changes - header file changes only
no functional or executable changes, hence no package bump
required
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
Kevin Darbyshire-Bryant [Wed, 19 Jun 2019 19:21:35 +0000 (20:21 +0100)]
kernel: update act_ctinfo
Follow upstream changes - header file changes
no executable difference at all
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
Linus Walleij [Thu, 20 Jun 2019 11:19:06 +0000 (13:19 +0200)]
gemini: Fix up DNS-313 compatible string
It's a simple typo in the DNS file, which was pretty serious.
No scripts were working properly. Fix it up.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
[integrate upstream patch into openwrt target]
Chris Koying Browet [Thu, 27 Dec 2018 12:07:40 +0000 (13:07 +0100)]
kernel: dm: add dm-raid for LVM raid
This adds the dm-raid kmod, which is needed for
LVM builtin raid configurations, aka "MD-over-LVM"
Signed-off-by: Chris Koying Browet <cbro@semperpax.com>
Christian Lamparter [Tue, 11 Dec 2018 17:40:04 +0000 (18:40 +0100)]
hostapd: remove stale WPA_SUPPLICANT_NO_TIMESTAMP_CHECK option
Support to disable the timestamp check for certificates in
wpa_supplicant (Useful for devices without RTC that cannot
reliably get the real date/time) has been accepted in the
upstream hostapd. It's implemented in wpa_supplicant as a
per-AP flag tls_disable_time_checks=[0|1].
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Petko Bordjukov [Sun, 9 Jun 2019 14:27:26 +0000 (17:27 +0300)]
kernel: package Broadcom BNX2X driver
bnx2x driver support for the x86 architecture. Includes module and
firmware for Broadcom QLogic 5771x/578xx 10/20-Gigabit ethernet
adapters.
Signed-off-by: Petko Bordjukov <bordjukov@gmail.com>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
[added +kmod-lib-zlib-inflate as well]
Jeff Kletsky [Sat, 15 Jun 2019 21:40:56 +0000 (14:40 -0700)]
ipq40xx: Linksys: sysupgrade: Ensure OEM volumes are removed
When OEM volumes are present in the [alt_]firmware partition,
sysupgrade will write a new kernel, but will fail to write
the root file system. The next boot will hang indefinitely
Waiting for root device /dev/ubiblock0_0...
Modified ipq40xx/base-files/lib/upgrade/linksys.sh
to remove both `squashfs` and `ubifs` if found
on the target firmware partition's UBI device.
Run-tested-on: Linksys EA8300
Signed-off-by: Jeff Kletsky <git-commits@allycomm.com>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
[applied some shellcheck suggestions as well]
Robinson Wu [Tue, 4 Jun 2019 03:13:39 +0000 (11:13 +0800)]
base-files: fix uci led oneshot/timer trigger
This patch adds a missing type property. This fixes
the creation of oneshot and timer led triggers like:
| ucidef_set_led_timer "system" "system" "zhuotk:green:system" "1000" "1000"
from /etc/init.d/01_leds.
Fixes: b06a286a4861 ("base-files: cleanup led functions in uci-defaults.sh")
Signed-off-by: Robinson Wu <wurobinson@qq.com>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Christian Lamparter [Sat, 15 Jun 2019 17:13:30 +0000 (19:13 +0200)]
apm821xx: fix bogus key-presses on boot
"There are often transient line events when
the system is powered up and initialized and it
is often necessary for the gpio_chip driver to
clear any interrupt flags in hardware before
setting up the gpio chip, especially the
irqchip portions of it."
<http://lists.infradead.org/pipermail/openwrt-devel/2019-June/017630.html>
This patch adds a fix for the APM821XX's interrupt
controller to clear any bogus pending toggled
interrupts that happens on various APM821XX boards
on boot.
The patch also changes the debouce-interval from the
default 5ms debounce interval to 60ms all around.
The default setting caused on occasions that the button
state became stuck in a pressed state, even though the
button was released.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Jo-Philipp Wich [Thu, 20 Jun 2019 16:07:49 +0000 (18:07 +0200)]
uhttpd: add direct dependency on libjson-c
The OpenWrt buildroot ABI version rebuild tracker does not handle
transient dependencies, therefor add all libraries linked by uhttpd
as direct dependencies to the corresponding binary package definition.
This ensures that uhttpd is automatically rebuilt and relinked if any
of these libraries has its ABI_VERSION updated in the future.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Jonas Gorski [Thu, 20 Jun 2019 15:02:30 +0000 (17:02 +0200)]
scripts/config: fix *c_shipped build depency tracking
The Makefile was missing dependencies on *c_shipped, so changes never
triggered a rebuild. Add these as optional dependencies so their absence
isn't treated as an error.
In addition, fix a typo preventing the zconf.lex.o from being removed on
clean.
Fixes: 9d5510a500a1 ("build: add new menuconfig code based on linux 3.9")
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Acked-by: Jo-Philipp Wich <jo@mein.io>
Koen Vandeputte [Thu, 20 Jun 2019 09:10:18 +0000 (11:10 +0200)]
kernel: bump 4.19 to 4.19.53
Refreshed all patches.
Compile-tested on: imx6
Runtime-tested on: imx6
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Koen Vandeputte [Thu, 20 Jun 2019 07:47:47 +0000 (09:47 +0200)]
kernel: bump 4.14 to 4.14.128
Refreshed all patches.
Compile-tested on: cns3xxx
Runtime-tested on: cns3xxx
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Kevin Darbyshire-Bryant [Tue, 18 Jun 2019 18:44:35 +0000 (19:44 +0100)]
kernel: generic: fix MIPS build on non-linux hosts
calc_vmlinuz_load_addr.c requires SZ_64K to be defined for alignment
purposes. It included "../../../../include/linux/sizes.h" to define
that size, however "sizes.h" tries to include <linux/const.h> which
assumes linux system headers. These may not exist eg. the following
error was encountered when building Linux for OpenWrt under macOS:
In file included from arch/mips/boot/compressed/calc_vmlinuz_load_addr.c:16:
arch/mips/boot/compressed/../../../../include/linux/sizes.h:11:10: fatal error: 'linux/const.h' file not found
Change makefile to force building on local linux headers instead of
system headers. Also change eye-watering relative reference in include
file spec.
Thanks to Jo-Philip Wich & Petr Štetiar for assistance in tracking this
down & fixing.
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
Jonas Gorski [Sat, 15 Jun 2019 13:04:53 +0000 (15:04 +0200)]
metadata: ensure one dependency provider to be y if a package is y
When there are multiple packages providing a meta-package, it is
possible to to create a config where a package is selected as =y, but
all of its dependency providers are just selected as =m. This is due to
the selection statement being just
config PACKAGE_foo
select PACKAGE_bar if !PACKAGE_baz
which is already fulfilled by PACKAGE_bar=m. Fix this by properly
comparing the selection states:
config PACKAGE_foo
select PACKAGE_bar if PACKAGE_baz<PACKAGE_foo
Also invert the select conditions to improve readability.
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
[slightly reword commit message]
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Jo-Philipp Wich [Sat, 15 Jun 2019 12:57:14 +0000 (14:57 +0200)]
treewide: fix syntax errors exposed after kconfig update
After commit
e82a4d9cfb ("config: regenerate *_shipped sources") the mconf
parser became more strict as a side effect and started to spew a series of
warnings when evaluating our generated kconfig sources:
tmp/.config-package.in:705:warning: ignoring unsupported character '@'
The root cause of these warnings is a wrong use of the @SYMBOL dependency
syntax in various Makefile. Fix the corresponding Makefiles by turning
`@SYM||@SYM2` expressions into the proper `@(SYM||SYM2)` form.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Nicolas Pitre [Sat, 15 Jun 2019 15:07:08 +0000 (17:07 +0200)]
config: fix relational operators for bool and tristate symbols
Since commit
31847b67bec0 ("kconfig: allow use of relations other than
(in)equality") it is possible to use relational operators in Kconfig
statements. However, those operators give unexpected results when
applied to bool/tristate values:
(n < y) = y (correct)
(m < y) = y (correct)
(n < m) = n (wrong)
This happens because relational operators process bool and tristate
symbols as strings and m sorts before n. It makes little sense to do a
lexicographical compare on bool and tristate values though.
Documentation/kbuild/kconfig-language.txt states that expression can have
a value of 'n', 'm' or 'y' (or 0, 1, 2 respectively for calculations).
Let's make it so for relational comparisons with bool/tristate
expressions as well and document them. If at least one symbol is an
actual string then the lexicographical compare works just as before.
Signed-off-by: Nicolas Pitre <nico@linaro.org>
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Tested-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
[rebased against OpenWrt kconfig, slightly reword commit message]
(backported from upstream
9059a3493efea6492451430c7e2fa0af799a2abb)
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Jonas Gorski [Sat, 15 Jun 2019 12:54:07 +0000 (14:54 +0200)]
config: regenerate *_shipped sources
The pregenerated `zconf.hash.c` and `zconf.lex.c` files have not been
kept in sync with their respective `*.y` and `*.l` sources in the past
causing our kconfig implementation to not recognize important kconfig
grammer elements such as relational `<`, `<=`, `>` and `>=` operators.
Fixes: 2d7e602381f3 ("scripts/config: sync with latest linux upstream")
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
[reword commit message]
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Jo-Philipp Wich [Thu, 20 Jun 2019 10:54:02 +0000 (12:54 +0200)]
procd: add direct dependencies on libblobmsg-json and libjson-c
The OpenWrt buildroot ABI version rebuild tracker does not handle
transient dependencies, therefor add all libraries linked by procd
as direct dependencies to the corresponding binary package definition.
This ensures that procd is automatically rebuilt and relinked
if any of these libraries has its ABI_VERSION updated in the
future.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Petr Štetiar [Thu, 20 Jun 2019 10:44:32 +0000 (12:44 +0200)]
ramips: fix EW-7478AC model name in DTS
This fixes lower case AC in the DTS model name.
Fixes: 88f7a29f99fb ("ramips: add support for Edimax EW-7476RPC / EW-7478AC")
Reported-by: Cezary Jackiewicz <cezary@eko.one.pl>
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Yousong Zhou [Thu, 20 Jun 2019 08:22:44 +0000 (08:22 +0000)]
netsupport: add kmod-nsh
This is required by kmod-openvswitch since linux 4.15.
Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
David Bauer [Tue, 18 Jun 2019 22:07:12 +0000 (00:07 +0200)]
ath79: correct various phy-mode properties
Upstream commit
6d4cd04 changes how the internal delays of the AR803x
based PHYs are enabled. With this commit, all internal delays are
disabled on driver probe and enabled based on the 'phy-mode' property in
the device-tree.
Before this commit, the RX delay was always enabled upon soft-reset
while the TX delay retained it's previous state. A hard reset enabled
the RX delay while the TX delay was disabled.
Because of this inconsistency, wrongly specified PHY-modes were working
correctly while the hardware was in a different state.
Fix the PHY-modes of some affected devices (and clean up misplaced
properties along the way) to keep the devices working flawlessly with
kernels >= 5.1.
Signed-off-by: David Bauer <mail@david-bauer.net>
Pawel Dembicki [Mon, 29 Oct 2018 20:50:13 +0000 (20:50 +0000)]
ramips: fix GELAN port in D-Link DWR-118-A2
This patch fix and enable GELAN port in D-LINK DWR-118-A2.
Tested-by: Richard Toth <trtk1992@gmail.com>
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
Pawel Dembicki [Mon, 29 Oct 2018 20:31:25 +0000 (20:31 +0000)]
ramips: mt7620: add EPHY base mdio address changing possibility
In some boards is requred to change the ephy mdio base address.
This patch add of property "mediatek,ephy-base-address" in gsw
part, which allows to change ephy base address.
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
[fixed indentation in header file]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Pawel Dembicki [Mon, 29 Oct 2018 17:30:22 +0000 (17:30 +0000)]
ramips: mt7620: fix external PHY autopolling
The port initialisation is based on assumption that phy address and
port number is the same. SoC allow different numbers and some board
have it.
Use phy address instead the port number to make sure that correct
addresses are polled.
In situation when only one PHY with address 0x0 is conected to
port 4, autopolling is broken.
This patch make autopolling correct when port number and phy address
are different.
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
Mathias Kresin [Tue, 17 Apr 2018 16:51:42 +0000 (18:51 +0200)]
ramips: handle mdio address and switch port seperate
The phy handling code forces a phy mdio address and the switch port to
which a phy is attached to be the same. Albeit such a configuration is
used for most boards, it isn't for all.
Pass the switch port number to the ethernet phy connect functions, to
ensure the correct list entry is edited and not the list entry that
matches th phys mdio address.
Use the mdio address with mdiobus_get_phy instead of the port number,
to make sure the expected ethernet phy gets connected.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Mathias Kresin [Wed, 4 Apr 2018 16:26:24 +0000 (18:26 +0200)]
ramips: ignore already handled ethernet phys
The whole logic in fe_phy_connect() is based on the asumption that mdio
address and switch port id are equal. Albeit it is true for most
boards, it doesn't is for all.
It isn't yet clear which subtargets/boards require the devicetree less
ethernet phy handling. Hence change the code in a way that it doesn't
touch ethernet phys which were early attached and are already handled.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Birger Koblitz [Tue, 18 Jun 2019 16:49:41 +0000 (18:49 +0200)]
ramips: add support for Edimax EW-7478APC
SoC: MediaTek MT7620a @ 580MHz
RAM: 64M (Winbond W9751G6KB-25)
FLASH: 8MB (Macronix)
WiFi: SoC-integrated: MediaTek MT7620a bgn
WiFi: MediaTek MT7612EN nac
Switch: Mediatek MT7530W Gigabit Switch (4 x LAN, 1 x WAN)
USB: Yes 1 x 2.0 (+ 1 x 2.0 unpopulated header)
BTN: Reset/WPS
LED: - Power (white)
- Internet (blue)
- Wifi (blue)
- USB (blue)
UART: UART is present as Pads with throughholes on the PCB. They are
located in the lower right corner (GbE ports facing up)
3.3V - RX - GND - TX / 57600-8N1
3.3V is the square pad
Installation
------------
Update the factory image via the web-interfaces (by default:
http://edimax.setup)
Signed-off-by: Birger Koblitz <mail@birger-koblitz.de>
[merge conflicts in 01_leds and mt7620.mk, dts whitespace issues]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Birger Koblitz [Mon, 3 Jun 2019 20:04:12 +0000 (22:04 +0200)]
ramips: add support for Edimax EW-7476RPC / EW-7478AC
SoC: MediaTek MT7620a @ 580MHz
RAM: 64M (Winbond W9751G6KB-25)
FLASH: 8MB (Macronix)
WiFi: SoC-integrated: MediaTek MT7620a bgn
WiFi: MediaTek MT7612EN nac
GbE: 1x (RTL8211E)
BTN: WPS - RFKILL/RF 50%/RF 100% toggle
LED: - Wifi 5g (blue)
- Wifi 2g (blue)
- Crossband (green)
- Power (green)
- WPS (green)
- LAN (Green)
UART: UART is present as Pads with throughholes on the PCB. They are
located next to the switch for the wifi configuration
3.3V - RX - GND - TX / 57600-8N1
3.3V is the square pad
Installation
------------
Update the factory image via the web-interfaces (by default:
192.168.9.2/24).
http://192.168.9.2/index.asp
ramips: add Edimax EW-7478AC
SoC: MediaTek MT7620a @ 580MHz
RAM: 64M (Winbond W9751G6KB-25)
FLASH: 8MB (Macronix)
WiFi: SoC-integrated: MediaTek MT7620a bgn
WiFi: MediaTek MT7612EN nac
GbE: 1x (RTL8211E)
BTN: WPS - RFKILL/RF 50%/RF 100% toggle
LED: - Wifi 5g (blue)
- Wifi 2g (blue)
- Crossband (green)
- Power (green)
- WPS (green)
- LAN (Green)
UART: UART is present as Pads with throughholes on the PCB. They are
located next to the switch for the wifi configuration
3.3V - RX - GND - TX / 57600-8N1
3.3V is the square pad
Installation
------------
Update the factory image via the web-interfaces (by default:
http://edimaxext.setup)
Or push wpa button on power on and send firmware via tftp to 192.168.1.6
The EW-7478AC is identical to the EW-7476RPC, except instead of 2 internal
antennas it has 2 external ones.
Signed-off-by: Birger Koblitz <mail@birger-koblitz.de>
[merge conflict in 01_leds]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Deng Qingfang [Tue, 30 Apr 2019 13:43:25 +0000 (21:43 +0800)]
libjson-c: update to 0.13.1
Signed-off-by: Deng Qingfang <dengqf6@mail2.sysu.edu.cn>
Vladimir Vid [Fri, 7 Jun 2019 13:50:50 +0000 (15:50 +0200)]
mvebu: fix regression for non-generic ESPRESSObin versions
When targets for multiple ESPRESSObin devices were added, not all
files were updated which means any ESPRESSObin version beside generic
won't have proper networking, sysupgrade and uboot-env. This patch
fixes the issue.
* fixup network detection
* fixup uboot-env
* fixup platform.sh for sysupgrade
Signed-off-by: Vladimir Vid <vladimir.vid@sartura.hr>
Vladimir Vid [Fri, 7 Jun 2019 13:58:15 +0000 (15:58 +0200)]
mvebu: image: fix generic-arm64.bootscript mmc selection
Not all versions of ESPRESSObin require SD card, but can
be booted from the internal emmc flash (mmc dev 1) instead.
Add a simple check in the bootscript to see which mmc device
is detected and boot from it using mmcdev variable.
Tested-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
Signed-off-by: Vladimir Vid <vladimir.vid@sartura.hr>
Petr Štetiar [Thu, 13 Jun 2019 11:48:27 +0000 (13:48 +0200)]
treewide: kernel: bump some targets to 4.19
Lets bump kernel to 4.19 on targets which were run tested or got ACKed
so we've enough time to make it ready for next release:
armvirt/32 (runtested in qemu)
armvirt/64 (runtested in qemu)
ath79/generic (runtested on Carambola2)
gemini/generic (runtested on DIR-685, DNS-313, SQ201, SL93512R)
imx6/generic (runtested on Apalis)
ipq40xx/generic (runtested on nbg6617)
malta/be64 (runtested in qemu)
malta/be (runtested in qemu)
malta/le (runtested in qemu)
malta/le64 (runtested in qemu)
mpc85xx/generic (runtested on TL-WDR4900)
mpc85xx/p2020 (runtested on P2020RDB)
mvebu/cortexa53
mvebu/cortexa72
mvebu/cortexa10
octeon/generic (runtested on EdgeRouter Lite)
sunxi/cortexa53 (build tested only)
sunxi/cortexa7 (runtested on Lime2-K)
sunxi/cortexa8 (build tested only)
tegra/generic
x86/64 (runtested in qemu)
Acked-by: Zoltan HERPAI <wigyori@uid0.hu> [sunxi]
Tested-by: Linus Walleij <linus.walleij@linaro.org> [gemini]
Tested-by: Tomasz Maciej Nowak <tomek_n@o2.pl> [mvebu, tegra]
Tested-by: Daniel Engberg <daniel.engberg.lists@pyret.net> [octeon]
Tested-by: Pawel Dembicki <paweldembicki@gmail.com> [mpc85xx/generic mpc85xx/p2020]
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Petr Štetiar [Thu, 13 Jun 2019 22:26:44 +0000 (22:26 +0000)]
kernel: generic: add missing DRM panel 4.19 config symbols
While building tegra/generic on 4.19, I've discovered few missing
symbols related to DRM panel symbols.
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Petr Štetiar [Thu, 13 Jun 2019 12:34:59 +0000 (12:34 +0000)]
kernel: generic: add missing 4.19 config symbol
Fixes following kernel build issue on ath79/generic:
Enable support for latency based cgroup IO protection (BLK_CGROUP_IOLATENCY) [N/y/?] (NEW)
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Petr Štetiar [Mon, 17 Jun 2019 05:27:46 +0000 (05:27 +0000)]
armvirt: refresh 4.19 kernel config
Refresh kernel configs with 4.19 bits, while at it, add common symbols
into the target config.
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Petr Štetiar [Sun, 16 Jun 2019 19:39:32 +0000 (19:39 +0000)]
armvirt: add kernel configs for 4.19
It's just copy of 4.14 and will be refreshed in the upcoming commit,
renamed config-default to config-4.14 as well.
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Koen Vandeputte [Tue, 18 Jun 2019 11:19:59 +0000 (13:19 +0200)]
kernel: bump 4.19 to 4.19.52
Refreshed all patches.
Fixes:
- CVE-2019-11479
- CVE-2019-11478
- CVE-2019-11477
Also fix a malformed patch issue caught during refresh.
It was caused by removing a whitespace without altering
the index values in a patch which alters a patch.
Compile-tested on: cns3xxx
Runtime-tested on: cns3xxx
Fixes: cf6526249298 ("kernel: bump 4.19 to 4.19.51")
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Koen Vandeputte [Tue, 18 Jun 2019 10:37:27 +0000 (12:37 +0200)]
kernel: bump 4.14 to 4.14.127
Refreshed all patches.
Fixes:
- CVE-2019-11479
- CVE-2019-11478
- CVE-2019-11477
Compile-tested on: cns3xxx
Runtime-tested on: cns3xxx
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Koen Vandeputte [Tue, 18 Jun 2019 09:49:03 +0000 (11:49 +0200)]
kernel: bump 4.9 to 4.9.182
Refreshed all patches.
Fixes:
- CVE-2019-11479
- CVE-2019-11478
- CVE-2019-11477
Compile-tested on: none
Runtime-tested on: none
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Koen Vandeputte [Mon, 17 Jun 2019 11:31:05 +0000 (13:31 +0200)]
kernel: bump 4.19 to 4.19.51
Refreshed all patches.
Altered patches:
- 370-netfilter-nf_flow_table-fix-offloaded-connection-tim.patch
- 220-optimize_inlining.patch
- 640-netfilter-nf_flow_table-add-hardware-offload-support.patch
This patch also restores the initial implementation
of the ath79 perfcount IRQ issue. (
78ee6b1a40b5)
It was wrongfully backported upstream initially and got reverted now.
Compile-tested on: cns3xxx, imx6
Runtime-tested on: cns3xxx, imx6
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
Koen Vandeputte [Mon, 17 Jun 2019 11:24:31 +0000 (13:24 +0200)]
kernel: bump 4.14 to 4.14.126
Refreshed all patches.
Altered patches:
- 220-optimize_inlining.patch
- 816-pcie-support-layerscape.patch
This patch also restores the initial implementation
of the ath79 perfcount IRQ issue. (
78ee6b1a40b5)
It was wrongfully backported upstream initially and got reverted now.
Compile-tested on: ar71xx, cns3xxx, imx6, x86_64
Runtime-tested on: ar71xx, cns3xxx, imx6
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
Petr Štetiar [Mon, 17 Jun 2019 13:25:40 +0000 (15:25 +0200)]
urngd: move project to git.openwrt.org
Let's move project to a proper place.
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Petr Štetiar [Thu, 13 Jun 2019 13:07:10 +0000 (15:07 +0200)]
ar71xx: make target source-only
Lets make it really explicit, that we should now focus only on ath79 in
order to make it ready for next release, where ar71xx is going to be
removed for good.
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Henryk Heisig [Sat, 23 Mar 2019 08:35:11 +0000 (08:35 +0000)]
ar71xx: base-files: fix board detect on new MikroTik devices
Move all MikroTik devices to new function to increase script execution
speed.
Machine name in new version of MikroTik RouterBOARD devices add "RB"
before model name:
Old machine name: MikroTik RouterBOARD 951Ui-2nD
New: MikroTik RouterBOARD RB951Ui-2nD
So this patch should fix it for all currently supported MikroTik boards.
Signed-off-by: Henryk Heisig <hyniu@o2.pl>
[rebased,commit message facelift,script fixes]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
[spotted missing 922UAGS-5HPacD]
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Petr Štetiar [Sat, 15 Jun 2019 09:28:05 +0000 (09:28 +0000)]
gpio-button-hotplug: fix 4.19 build breakage on malta/be64
While testing 4.19 build on malta/be64, I've encountered following
error:
gpio-button-hotplug/gpio-button-hotplug.c:529:18: error: implicit
declaration of function 'gpio_to_desc'
which is caused by the missing include fixed by this patch.
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Petr Štetiar [Thu, 13 Jun 2019 22:38:22 +0000 (22:38 +0000)]
tegra: add missing kernel symbol to 4.19 config
This patch adds missing kernel config symbol to 4.19 kernel config.
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Petr Štetiar [Thu, 13 Jun 2019 22:32:46 +0000 (22:32 +0000)]
tegra: refresh 4.19 kernel config
This patch refreshes Tegra's 4.19 kernel config.
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Marko Ratkaj [Thu, 13 Jun 2019 14:40:46 +0000 (16:40 +0200)]
mvebu: add kernel 4.19 support
Signed-off-by: Marko Ratkaj <marko.ratkaj@sartura.hr>
[added sfp related patches from Russell King]
Signed-off-by: Marek Behún <marek.behun@nic.cz>
[rebase; rework patches; separate and cleanup kernel configs;
add espessobin dts; adjust venom dts]
Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
Tomasz Maciej Nowak [Thu, 13 Jun 2019 14:40:47 +0000 (16:40 +0200)]
kernel: package module for SafeXcel crypto engine
Supports EIP97 and EIP197 found on Armada 37xx, 7k and 8k SoCs.
Unfortunately firmware for EIP197 is not easily obtainable, therefore
to not cause lot of user requests directed at OpenWrt, package it as
module with explanation where to obtain the firmware.
Cc: Marek Behún <marek.behun@nic.cz>
Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
Rafał Miłecki [Mon, 17 Jun 2019 04:53:07 +0000 (06:53 +0200)]
kernel: backport 4.18 patch adding DMI_PRODUCT_SKU
It's needed for applying some hardware quirks. This fixes:
drivers/net/wireless/broadcom/brcm80211/brcmfmac/dmi.c:60:20: error: 'DMI_PRODUCT_SKU' undeclared here (not in a function); did you mean 'DMI_PRODUCT_UUID'?
DMI_EXACT_MATCH(DMI_PRODUCT_SKU, "T8"),
Fixes: 8888cb725d49 ("mac80211: brcm: backport remaining brcmfmac 5.2 patches")
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Hauke Mehrtens [Sun, 16 Jun 2019 20:54:23 +0000 (22:54 +0200)]
uhttpd: Fix format string build problems
91fcac34ac uhttpd: Fix multiple format string problems
Fixes: fc454ca15305 libubox: update to latest git HEAD
Reported-by: Hannu Nyman <hannu.nyman@iki.fi>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Hans Dedecker [Sun, 16 Jun 2019 19:27:04 +0000 (21:27 +0200)]
nghttp2: bump to 1.39.1
7ffc239b Bump up version number to 1.39.1
bc886a0e Fix FPE with default backend
a3a14a9c Fix log-level is not set with cmd-line or configuration file
acfb3607 Update manual pages
bdfd14c2 Bump up version number to 1.39.0, LT revision to 31:4:17
cddc09fe Update AUTHORS
3c3b6ae8 Add missing colon
2f83aa9e Fix multi-line text travis issue
fc591d0c Run nghttpx integration test with cmake build
9a17c3ef travis: use multi-line text
b7220f07 cmake: Remove SPDY related files
a1556fd1 Merge pull request #1356 from nghttp2/fix-log-level-on-reload
77f1c872 nghttpx: Fix unchanged log level on configuration reload
49ce44e1 Merge pull request #1352 from nghttp2/travis-osx
f54b3ffc Fix libxml2 CFLAGS output
b0f5e5cc Implement daemon() using fork() for OSX
8d6ecd66 Enable osx build on travis
f82fb521 Update doc
2e1975dd clang-format-8
97ce392b Merge pull request #1347 from nghttp2/nghttpx-ignore-cl-te-on-upgrade
afefbda5 Ignore content-length in 200 response to CONNECT request
4fca2502 nghttpx: Ignore Content-Length and Transfer-Encoding in 1xx or 200 to CONNECT
6975c336 Update llhttp to 1.1.3
0288093c Fix llhttp_get_error_pos usage
a3a03481 Merge pull request #1340 from nghttp2/nghttpx-llhttp
c64d2573 Replace http-parser with llhttp
f028cc43 clang-format
302e3746 Merge pull request #1337 from nghttp2/upgrade-mruby
3cdbc5f5 Merge pull request #1335 from adamgolebiowski/boost-1.70
a6925186 Fix mruby build error
45d63d20 Upgrade mruby to 2.0.1
cbba1ebf asio: support boost-1.70
e86d1378 Bump up version number to 1.39.0-DEV
4a9d2005 Update manual pages
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
Hauke Mehrtens [Sun, 16 Jun 2019 16:59:04 +0000 (18:59 +0200)]
urngd: Fix more wrong type in format string
Also the other type is worng and causes compile problems on ARM64
platforms.
Fixes: 9b53201d9c53 ("urngd: Fix wrong type in format string")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
George Amanakis [Thu, 13 Jun 2019 04:03:38 +0000 (00:03 -0400)]
mvebu: fixes commit
a7e68927d0
err_free_stats has been deprecated. Replace with err_netdev.
Compile-tested on: mvebu
Runtime-tested on: mvebu
Fixes: a7e68927d047 ("kernel: bump 4.14 to 4.14.125 (FS#2305 FS#2297)")
Signed-off-by: George Amanakis <gamanakis@gmail.com>
Rafał Miłecki [Sun, 16 Jun 2019 16:56:15 +0000 (18:56 +0200)]
mac80211: brcm: backport remaining brcmfmac 5.2 patches
This improves FullMAC firmware compatibility, adds logging in case of
firmware crash and *may* fix "Invalid packet id" errors.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Hauke Mehrtens [Sun, 12 May 2019 16:49:24 +0000 (18:49 +0200)]
kernel: Activate CONFIG_OPTIMIZE_INLINING
This will reduce the size of the kernel if CONFIG_CC_OPTIMIZE_FOR_SIZE is
set like for all targets with small_flash feature flag.
I haven't seen any changes for an ARM64 target which optimizes the
kernel for speed instead.
On the ath79/tiny target the uncompressed kernel size was reduced by
3.2% and the compressed kernel size by 2.1%
kernel size with CONFIG_OPTIMIZE_INLINING=n
4346412 build_dir/target-mips_24kc_musl/linux-ath79_tiny/vmlinux
1391169 build_dir/target-mips_24kc_musl/linux-ath79_tiny/tplink_tl-wr941-v4-kernel.bin
Kernel size with CONFIG_OPTIMIZE_INLINING=y
4212396 build_dir/target-mips_24kc_musl/linux-ath79_tiny/vmlinux
1362051 build_dir/target-mips_24kc_musl/linux-ath79_tiny/tplink_tl-wr941-v4-kernel.bin
This change is currently pending for kernel 5.2 and already in
linux-next, this updates our patch to match the upstream version.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
André Valentin [Fri, 14 Jun 2019 11:09:46 +0000 (13:09 +0200)]
netsupport: improve xfrm module support
-switch to module autoprobe
-exclude 4.9 kernel
Signed-off-by: André Valentin <avalentin@marcant.net>
Hauke Mehrtens [Sun, 16 Jun 2019 14:36:13 +0000 (16:36 +0200)]
libubox: update to latest git HEAD
9dd2dcf libubox: add format string checking to ulog()
ecf5617 ustream: Add format string checks to ustream_(v)printf()
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Joseph Benden [Wed, 8 May 2019 18:52:56 +0000 (11:52 -0700)]
toolchain: Add GCC 9.1.0 release
Most of the patches are copied over from GCC 8.3.
The following patches are backported from the GCC 9.X development branch:
toolchain/gcc/patches/9.1.0/970-recompute-dom-fast-queries-before-vn.patch
toolchain/gcc/patches/9.1.0/975-g++-ICE-with-generic-lambda.patch
The specs file changed with gcc 9, now it contains "%@{L*}" instead of
"%{L*}" in older GCC versions.
Signed-off-by: Joseph Benden <joe@benden.us>
Hauke Mehrtens [Sun, 16 Jun 2019 14:38:56 +0000 (16:38 +0200)]
urngd: Fix wrong type in format string
GCC 9.1 complains about this wrong type used in the format string, fix
this to make the compiler happy.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Hauke Mehrtens [Sun, 16 Jun 2019 13:48:44 +0000 (15:48 +0200)]
ubox: bump to git HEAD
4df34a4 kmodloader: Increase path array size to make it always fit
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Hans Dedecker [Sat, 15 Jun 2019 19:25:03 +0000 (21:25 +0200)]
netifd: xfrm fixes
9932ed0 netifd: fix xfrm interface deletion and standardize netlink call
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
projects / openwrt / staging / chunkeey.git / log