Florian Fainelli [Fri, 10 Aug 2012 07:04:16 +0000 (07:04 +0000)]
set a compatible command-line to boot from flash
SVN-Revision: 33078
Gabor Juhos [Fri, 10 Aug 2012 06:32:00 +0000 (06:32 +0000)]
generic: rtl8366_smi: increase delay after switch hw reset
SVN-Revision: 33077
Jo-Philipp Wich [Thu, 9 Aug 2012 22:44:52 +0000 (22:44 +0000)]
netifd: call "wifi down" before "wifi up"
When the underlying /etc/config/wireless got changed since the last "wifi up"
has been performed, the uci vap ifname state vars become inconsistent on a
subsequent "wifi up" and multiple vaps get mapped to the same ifnames which
confuses the gui and other processes relying on them.
For now call an explicit "wifi down" prior to each "wifi up" which will clear
up the state accordingly.
SVN-Revision: 33076
Jo-Philipp Wich [Thu, 9 Aug 2012 18:30:47 +0000 (18:30 +0000)]
base-files: fix option parsing of -F/--force parameter
SVN-Revision: 33075
Jonas Gorski [Thu, 9 Aug 2012 13:13:26 +0000 (13:13 +0000)]
package: linux-atm: br2684ct: fix nas interface bringup on boot
Give nas interface time to setup them selves before configuring them.
Should fix #11826.
Contributed by T-Labs, Deutsche Telekom Innovation Laboratories
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
SVN-Revision: 33074
Jo-Philipp Wich [Thu, 9 Aug 2012 09:41:22 +0000 (09:41 +0000)]
Fix hard reset of alix/soekris hardware under heavy NIC load
The following patch corrects a hard reset that occurs on alix and
soekris net5501 hardware. Specifically, this is an issue with the via
rhine NIC driver. Under periods of extreme load, the via rhine driver
can cause a reset of the entire system. When this happens no output is
seen on the console, the device simply reboots. This was reported in the
following ticket:
Consistent crash on Soekris NET5501
https://dev.openwrt.org/ticket/11882
I was able to reproduce the problem locally with numerous alix 2d13
platforms. Under heavy 64 byte frame size load from a Smartbits traffic
generator, the alix hardware will hard reset in under 5 minutes. The
same hardware, under the same load, on FreeBSD 9.0 does not reset.
The patch below backports most of the via rhine changes from kernel 3.5.
With OpenWrt trunk being on kernel 3.3.8, it seemed prudent to bring
these changes in to avoid this serious issue.
I've tested this heavily in my test environment and was able to keep the
device stable under load for extended periods of time without any resets.
Also, a nice side effect of this change is that it significantly raises
the performance the platform. Without this patch the alix 2d13 can move
approximately 29,000 packets per second at 64 byte frame sizes. After
this patch the alix can move 52,000 packets per second at 64 byte frame
sizes.
I put this patch under the x86 patches as those are the only platforms
with via rhine hardware that I'm aware of. If it needs to go some place
else please let me know.
Thanks,
Adam
Signed-off-by: Adam Gensler <openwrt@kristenandadam.net>
SVN-Revision: 33072
Florian Fainelli [Thu, 9 Aug 2012 09:06:35 +0000 (09:06 +0000)]
nuport-mac: use dma_mapping_error() instead of checking pointers
Thanks Gabor for spotting this
SVN-Revision: 33071
Florian Fainelli [Wed, 8 Aug 2012 21:51:18 +0000 (21:51 +0000)]
nuport-mac: rework PHY interrupt configuration to avoid races
SVN-Revision: 33070
Florian Fainelli [Wed, 8 Aug 2012 21:51:13 +0000 (21:51 +0000)]
nuport-mac: close possible race condition during start
SVN-Revision: 33069
Florian Fainelli [Wed, 8 Aug 2012 21:51:09 +0000 (21:51 +0000)]
nuport-mac: unmap the DMA buffer when closing device
SVN-Revision: 33068
Florian Fainelli [Wed, 8 Aug 2012 21:51:04 +0000 (21:51 +0000)]
nuport-mac: check dma_map_single address return values
SVN-Revision: 33067
Florian Fainelli [Wed, 8 Aug 2012 21:51:00 +0000 (21:51 +0000)]
build a Devolo dLAN USB Extender specific image
The kernel has to be rounded up to the nearest 1MB, then we append
the root filesystem at its end.
SVN-Revision: 33066
Florian Fainelli [Wed, 8 Aug 2012 21:50:55 +0000 (21:50 +0000)]
cleanup image generation
SVN-Revision: 33065
Felix Fietkau [Wed, 8 Aug 2012 18:23:04 +0000 (18:23 +0000)]
ath9k: fix handling of decryption errors, should improve link stability
SVN-Revision: 33063
Felix Fietkau [Wed, 8 Aug 2012 18:23:00 +0000 (18:23 +0000)]
ath5k: revert a buggy tx power related patch
SVN-Revision: 33062
Florian Fainelli [Wed, 8 Aug 2012 15:37:34 +0000 (15:37 +0000)]
base-files: check for ldd presence and executability (#11991)
SVN-Revision: 33057
Felix Fietkau [Wed, 8 Aug 2012 12:56:44 +0000 (12:56 +0000)]
ath9k: fix hang issues on hw reset caused by interrupt storms
SVN-Revision: 33055
John Crispin [Wed, 8 Aug 2012 12:14:43 +0000 (12:14 +0000)]
pci gpio mapping
This patch fixes the GPIO ALTSEL settings for some of the GPIOs used by the PCI subsystem in Lantiq Danube. These changes are required for more than one PCI device to work. Tested with an ARV7510PW having two PCI-devices; a VIA USB controller and a Ralink WLAN mini-PCI card.
Signed-off-by: Matti Laakso <malaakso@elisanet.fi>
SVN-Revision: 33054
Jo-Philipp Wich [Wed, 8 Aug 2012 11:13:12 +0000 (11:13 +0000)]
hostapd: fix ap/sta regression which got accidentally introduced by r32829 (#11914)
SVN-Revision: 33053
Florian Fainelli [Tue, 7 Aug 2012 16:08:11 +0000 (16:08 +0000)]
busybox: support V=c toplevel verboseness flag (#11799)
Signed-off-by: Gregory M. Turner <gmt@malth.us>
SVN-Revision: 33035
Florian Fainelli [Tue, 7 Aug 2012 16:08:08 +0000 (16:08 +0000)]
w1-gpio-custom: set enable_external_pullup to null (#8952)
SVN-Revision: 33034
Felix Fietkau [Tue, 7 Aug 2012 09:36:24 +0000 (09:36 +0000)]
ath9k: completely disable the MIB interrupt from the interrupt mask register to prevent potential interrupt storms
SVN-Revision: 33032
Felix Fietkau [Mon, 6 Aug 2012 22:11:30 +0000 (22:11 +0000)]
ath9k: extend and enable PA predistortion
SVN-Revision: 33031
Felix Fietkau [Mon, 6 Aug 2012 20:18:07 +0000 (20:18 +0000)]
mac80211: do not delete linux/*_platform.h, they are touched by patches. instead make the build fail if they differ from the ones in the kernel tree to prevent subtle runtime issues (see #11981)
SVN-Revision: 33030
John Crispin [Mon, 6 Aug 2012 18:56:38 +0000 (18:56 +0000)]
fixes tapi dependencies
SVN-Revision: 33029
John Crispin [Mon, 6 Aug 2012 18:54:36 +0000 (18:54 +0000)]
fixes package description
SVN-Revision: 33028
Felix Fietkau [Mon, 6 Aug 2012 15:33:24 +0000 (15:33 +0000)]
ath5k: add various pending tx power fixes, vastly improves stability and performance with various cards
SVN-Revision: 33014
Hauke Mehrtens [Sun, 5 Aug 2012 23:43:36 +0000 (23:43 +0000)]
mac80211: remove header files used to share struct with platform code.
The structs defined in these header files should be the same as the
structes used by the platform code otherwise it will cause strange
runtime errors. By removing them from compat-wireless we will get a
compile error instead of a runtime error if they are out of sync.
SVN-Revision: 33006
Jonas Gorski [Sun, 5 Aug 2012 23:18:22 +0000 (23:18 +0000)]
bcm63xx: fix USB base registers and IRQs for BCM6328
SVN-Revision: 33005
Hauke Mehrtens [Sun, 5 Aug 2012 20:27:40 +0000 (20:27 +0000)]
update tg3 driver
SVN-Revision: 33004
Hauke Mehrtens [Sun, 5 Aug 2012 13:14:00 +0000 (13:14 +0000)]
generate image for Linksys e3200
SVN-Revision: 33003
Hauke Mehrtens [Sun, 5 Aug 2012 13:10:43 +0000 (13:10 +0000)]
switch: clean up robo switch driver
* remove use_et, all supported drivers are using mii ioctls
* remove robo.phy_addr, phy_addr was always set to ROBO_PHY_ADDR.
* remove support for old kernel versions
* do_ioctl is allways called with buff == NULL
* use if_mii
SVN-Revision: 33002
Hauke Mehrtens [Sun, 5 Aug 2012 12:40:05 +0000 (12:40 +0000)]
brcm47xx: update gpio patch
SVN-Revision: 33001
Hauke Mehrtens [Sun, 5 Aug 2012 12:39:15 +0000 (12:39 +0000)]
brcm47xx: fix patch which moves the flash struct in wgt634u code
SVN-Revision: 33000
John Crispin [Sun, 5 Aug 2012 08:16:50 +0000 (08:16 +0000)]
fix xen pci module, partially fixes #11970
SVN-Revision: 32996
John Crispin [Sat, 4 Aug 2012 20:14:52 +0000 (20:14 +0000)]
W502V/ARV4525 wireless mac bugfix
The ARV4525 board init is passing the wrong offset to
arv_register_ath5k() resulting in a bogus mac.
Signed-off-by: Tobias Diedrich <ranma+openwrt@tdiedrich.de>
SVN-Revision: 32993
Hauke Mehrtens [Sat, 4 Aug 2012 19:46:25 +0000 (19:46 +0000)]
brcm47xx: use libgpio instaed of implementing the gpio interface ourself.
SVN-Revision: 32992
John Crispin [Sat, 4 Aug 2012 19:17:49 +0000 (19:17 +0000)]
gspca-sn9c20x.ko was not insmod'ed due to typo
fixes #11973
SVN-Revision: 32991
John Crispin [Fri, 3 Aug 2012 09:38:24 +0000 (09:38 +0000)]
wrt55agv2-spidevs needs <linux/modules.h>
SVN-Revision: 32956
John Crispin [Fri, 3 Aug 2012 08:53:02 +0000 (08:53 +0000)]
cleanup patches
SVN-Revision: 32953
Florian Fainelli [Thu, 2 Aug 2012 18:13:17 +0000 (18:13 +0000)]
nuport-mac: properly protect the phy interrupt handler
SVN-Revision: 32951
John Crispin [Thu, 2 Aug 2012 13:39:50 +0000 (13:39 +0000)]
Codel: avoid a nul rec_inv_sqrt
One condition before codel_Newton_step() was not good if
we never left the dropping state for a flow. As a result
rec_inv_sqrt was 0, instead of the ~0 initial value.
codel control law was then set to a very aggressive mode, dropping
many packets before reaching 'target' and recovering from this problem.
Brought over from 3.5-stable
Signed-off-by: Dave Taht <dave.taht@bufferbloat.net>
SVN-Revision: 32950
John Crispin [Thu, 2 Aug 2012 13:29:49 +0000 (13:29 +0000)]
fixes i2c clock enable
SVN-Revision: 32949
Gabor Juhos [Thu, 2 Aug 2012 11:25:49 +0000 (11:25 +0000)]
ar71xx: simplify misc IRQ handling
SVN-Revision: 32948
Gabor Juhos [Thu, 2 Aug 2012 11:25:46 +0000 (11:25 +0000)]
ar71xx: fix AR934X_EHCI_SIZE
SVN-Revision: 32947
Gabor Juhos [Thu, 2 Aug 2012 09:54:41 +0000 (09:54 +0000)]
ar71xx: image: stop the switch from the lzma-loader on the TL-WR1043ND
SVN-Revision: 32946
Gabor Juhos [Thu, 2 Aug 2012 09:54:33 +0000 (09:54 +0000)]
ar71xx: image: allow to use board specific code in the lzma-loader
SVN-Revision: 32945
Gabor Juhos [Thu, 2 Aug 2012 09:54:28 +0000 (09:54 +0000)]
ar71xx: init switch hw_reset on the TL-WR1043ND board
SVN-Revision: 32944
Gabor Juhos [Thu, 2 Aug 2012 09:54:21 +0000 (09:54 +0000)]
generic: rtl836x: add hw_reset field to struct rtl8366_smi
It will be used to start/stop the switch if that is
supported by the given board.
SVN-Revision: 32943
Gabor Juhos [Thu, 2 Aug 2012 09:54:13 +0000 (09:54 +0000)]
generic: rtl8366_smi: use __rtl8366_smi_cleanup instead of gpio_free calls
SVN-Revision: 32942
Florian Fainelli [Wed, 1 Aug 2012 22:09:13 +0000 (22:09 +0000)]
add missing netmask to the network config
SVN-Revision: 32941
Florian Fainelli [Wed, 1 Aug 2012 21:56:54 +0000 (21:56 +0000)]
assume the link is up and full-duplex by default
SVN-Revision: 32940
Florian Fainelli [Wed, 1 Aug 2012 21:56:49 +0000 (21:56 +0000)]
add a default and suitable network config file
SVN-Revision: 32939
Gabor Juhos [Wed, 1 Aug 2012 12:24:57 +0000 (12:24 +0000)]
ar71xx: ew-dorin: added router firmware generation
[juhosg: remove dead code]
Signed-off-by: embedded wireless GmbH <info@embeddedwireless.de>
SVN-Revision: 32934
Gabor Juhos [Wed, 1 Aug 2012 12:24:56 +0000 (12:24 +0000)]
ar71xx: ew-dorin: added USB support
Signed-off-by: embedded wireless GmbH <info@embeddedwireless.de>
SVN-Revision: 32933
Gabor Juhos [Wed, 1 Aug 2012 12:24:54 +0000 (12:24 +0000)]
ar71xx: Buffalo WLAE-AG300N wireless led patch
Here is the uci-defaults version of the led support for
the Buffalo WLAE-AG300N.
Signed-off-by: Yoichi Shinoda <shinoda@jaist.ac.jp>
SVN-Revision: 32932
Gabor Juhos [Wed, 1 Aug 2012 12:24:52 +0000 (12:24 +0000)]
ar71xx: Buffalo WLAE-AG300N initial support
The patch set for Buffalo WLAE-AG300N initial support.
There is another patch for wireless led support that
is posted separately.
Note on serial console:
This unit has buffalo standard 4 pin console, but the unit may not power
on if some console apparatus is connected. This is probably due to some
electronic interaction between the unit's electronic power switch circuit
and the serial console apparatus. If this happens, it is required to power
on the unit without the console, then quickly (re-)attach it.
[juhosg: fix coding style]
Signed-off-by: Yoichi Shinoda <shinoda@jaist.ac.jp>
SVN-Revision: 32931
Florian Fainelli [Wed, 1 Aug 2012 12:01:27 +0000 (12:01 +0000)]
resync defconfig enable XZ compression
SVN-Revision: 32930
Florian Fainelli [Wed, 1 Aug 2012 12:01:24 +0000 (12:01 +0000)]
uclibc++: update to 0.2.4
SVN-Revision: 32929
Florian Fainelli [Wed, 1 Aug 2012 12:01:18 +0000 (12:01 +0000)]
uclibc++: stage g++-uc wrappers in $(TOOLCHAIN_DIR)
Since we are overriding TARGET_CXX with the g++-uc wrapper when
we use cmake it expects to find g++-uc in the TOOLCHAIN_DIR.
SVN-Revision: 32928
Florian Fainelli [Tue, 31 Jul 2012 23:09:50 +0000 (23:09 +0000)]
properly generate squashfs, jffs2 and initramfs images and kernels
SVN-Revision: 32927
Florian Fainelli [Tue, 31 Jul 2012 23:09:46 +0000 (23:09 +0000)]
disable crashlog on ARM platforms for the moment
It is currently badly broken on ARM, until fixed, disable it
SVN-Revision: 32926
John Crispin [Tue, 31 Jul 2012 18:49:54 +0000 (18:49 +0000)]
add lantiq svip support
SVN-Revision: 32925
Jonas Gorski [Tue, 31 Jul 2012 14:27:47 +0000 (14:27 +0000)]
bcm63xx: Add nb6 support (BCM6362 SoC base boards)
Signed-off-by: Miguel GAIO <miguel.gaio@efixo.com>
Signed-off-by: Jonas Gorski <jonas.gorski+openwrt@gmail.com>
[jonas.gorski@gmail.com: add network config for nb6, make switch fix a
platform patch]
SVN-Revision: 32924
Jonas Gorski [Tue, 31 Jul 2012 14:27:42 +0000 (14:27 +0000)]
bcm63xx: add basic bcm6362 support
Signed-off-by: Jonas Gorski <jonas.gorski+openwrt@gmail.com>
SVN-Revision: 32923
Jonas Gorski [Tue, 31 Jul 2012 14:27:34 +0000 (14:27 +0000)]
bcm63xx: enable usb for bcm6328
Signed-off-by: Jonas Gorski <jonas.gorski+openwrt@gmail.com>
SVN-Revision: 32922
Jonas Gorski [Tue, 31 Jul 2012 14:27:31 +0000 (14:27 +0000)]
bcm63xx: update enetswitch driver
Update enetswith driver with latest fixes and additions.
Signed-off-by: Jonas Gorski <jonas.gorski+openwrt@gmail.com>
SVN-Revision: 32921
Jonas Gorski [Tue, 31 Jul 2012 14:27:25 +0000 (14:27 +0000)]
bcm63xx: reorder patches
Fix the order and names of patches.
Signed-off-by: Jonas Gorski <jonas.gorski+openwrt@gmail.com>
SVN-Revision: 32920
Florian Fainelli [Sun, 29 Jul 2012 13:20:51 +0000 (13:20 +0000)]
move i2c module to target modules.mk
SVN-Revision: 32910
Florian Fainelli [Sun, 29 Jul 2012 13:20:47 +0000 (13:20 +0000)]
partially revert r32855
Too many modules were removed, while only the octeon module was meant to be
removed, fix that.
SVN-Revision: 32909
Florian Fainelli [Sun, 29 Jul 2012 13:20:39 +0000 (13:20 +0000)]
resync config
SVN-Revision: 32908
Florian Fainelli [Sun, 29 Jul 2012 13:20:35 +0000 (13:20 +0000)]
use the same description as other omap platforms (without the dash)
SVN-Revision: 32907
John Crispin [Sun, 29 Jul 2012 11:53:06 +0000 (11:53 +0000)]
refresh pwm patch
SVN-Revision: 32905
John Crispin [Sun, 29 Jul 2012 09:07:47 +0000 (09:07 +0000)]
dont build on arm as kernel headers are missing/have a different layout
SVN-Revision: 32904
John Crispin [Sat, 28 Jul 2012 21:06:59 +0000 (21:06 +0000)]
fix up scons vs ccache
SVN-Revision: 32902
John Crispin [Sat, 28 Jul 2012 20:47:08 +0000 (20:47 +0000)]
clean up pwm patches and drivers
SVN-Revision: 32901
Hauke Mehrtens [Sat, 28 Jul 2012 11:36:52 +0000 (11:36 +0000)]
add config option CONFIG_I2C_MV64XXX to fix kirkwood build
SVN-Revision: 32898
Florian Fainelli [Fri, 27 Jul 2012 15:35:15 +0000 (15:35 +0000)]
resync config
SVN-Revision: 32895
Florian Fainelli [Fri, 27 Jul 2012 15:35:12 +0000 (15:35 +0000)]
fix DVA-G3810BN image generation
Attached patch fixes a typo in the image Makefile, and overrides the
board name for DVA-G3810BN to set the correct board properties
Signed-Off-By: Jeroen van Bemmel <jbemmel@zonnet.nl>
SVN-Revision: 32894
Florian Fainelli [Fri, 27 Jul 2012 15:35:09 +0000 (15:35 +0000)]
add D-link DVA-G3810BN-TL-1 support
Signed-Off-By: Jeroen van Bemmel <jbemmel@zonnet.nl>
SVN-Revision: 32893
Florian Fainelli [Fri, 27 Jul 2012 15:35:05 +0000 (15:35 +0000)]
Add CT6376-1 board support
Added CT6373 devices instead of using NB4's devices, as Florian suggested.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
SVN-Revision: 32892
Florian Fainelli [Fri, 27 Jul 2012 15:35:00 +0000 (15:35 +0000)]
base-files: fix detection of standalone ldd
When standalone ldd is selected in config the binary is installed in /usr/bin/ldd.
Signed-off-by: Michael Heimpold <mhei@heimpold.de>
SVN-Revision: 32891
Florian Fainelli [Fri, 27 Jul 2012 15:34:57 +0000 (15:34 +0000)]
Add brcmsmac profile
Add brcmsmac profile (kmod-brcmsmac + wpad-mini).
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
SVN-Revision: 32890
John Crispin [Fri, 27 Jul 2012 08:30:05 +0000 (08:30 +0000)]
mae brcmutil depend on PCI and USB. This broke ar7 fullbuilds
SVN-Revision: 32886
John Crispin [Thu, 26 Jul 2012 17:06:55 +0000 (17:06 +0000)]
Add leds back after migration to sysfs
atheros trunk moved to full sysfs gpiolib, but the leds were forgotten.
This restores the wlan led that was missing after switching from backfire
to trunk.
Signed-off-by: Karl Palsson <karlp@remake.is>
SVN-Revision: 32885
Florian Fainelli [Thu, 26 Jul 2012 17:03:08 +0000 (17:03 +0000)]
add more missing config symbols
SVN-Revision: 32884
Florian Fainelli [Thu, 26 Jul 2012 17:03:05 +0000 (17:03 +0000)]
add more USB-related config symbols
SVN-Revision: 32883
Florian Fainelli [Thu, 26 Jul 2012 17:03:02 +0000 (17:03 +0000)]
make sure target modules depend on the target
SVN-Revision: 32882
Hauke Mehrtens [Thu, 26 Jul 2012 15:42:18 +0000 (15:42 +0000)]
bcma: update to version from wireless-testing tag master-2012-07-16
I did not add the last patch, because it add some stubs for the flash drivers and our patches have to be changed for that, if the flash support in bcma is able to do something I will integrate it.
This also contains 3 additional patches fixing some bugs in bcma.
SVN-Revision: 32880
Florian Fainelli [Thu, 26 Jul 2012 09:29:22 +0000 (09:29 +0000)]
make kmod-mvsas depend on x86 since it fails building on other targets (eg: brcm63xx)
SVN-Revision: 32878
John Crispin [Wed, 25 Jul 2012 19:52:30 +0000 (19:52 +0000)]
fix typo in modules.mk
This patch fixes a small typo in kmod-leds-wndr3700-usb description, where the board is for some reason made by NETGWR, not NETGEAR.
Signed-off-by: Roman A. aka BasicXP <x12ozmouse@ya.ru>
SVN-Revision: 32870
Florian Fainelli [Wed, 25 Jul 2012 19:36:19 +0000 (19:36 +0000)]
make kmod-fb dependent on DISPLAY_SUPPORT and update targets accordingly
SVN-Revision: 32869
Felix Fietkau [Wed, 25 Jul 2012 17:28:32 +0000 (17:28 +0000)]
mtd: fix trx_fixup
With the BRCM47xx image I have built (Linksys E3000), there are additional
writes following the completion of "mtd_replace_jffs2" which invalidate the
'trx_fixup' performed by 'mtd_replace_jffs2'. Moving the 'trx_fixup' to somewhere
after all writes have completed fixes the problem. I also noticed that 'erasesize'
used to compute 'block_offset' in 'mtd_fixtrx' is used before it is computed by
'mtd_check_open'; moving the call to 'mtd_check_open' up a few lines fixes this.
Unlike 'mtd_fixtrx', 'trx_fixup' appears to assume that the TRX header is always at
offset 0; which may be the cause of the problem described in Ticket #8960.
Signed-off-by: Nathan Hintz <nlhintz@hotmail.com>
SVN-Revision: 32866
Florian Fainelli [Wed, 25 Jul 2012 15:50:45 +0000 (15:50 +0000)]
move isp116x driver to target specific modules.mk
SVN-Revision: 32865
Florian Fainelli [Wed, 25 Jul 2012 15:50:42 +0000 (15:50 +0000)]
move rt305x-dwc driver to target specific modules.mk
SVN-Revision: 32864
Florian Fainelli [Wed, 25 Jul 2012 15:50:38 +0000 (15:50 +0000)]
move ubsec-ssb driver to target specific modules.mk
SVN-Revision: 32863
Florian Fainelli [Wed, 25 Jul 2012 15:50:36 +0000 (15:50 +0000)]
move ssb-gige to target specific modules.mk
SVN-Revision: 32862
Florian Fainelli [Wed, 25 Jul 2012 15:50:33 +0000 (15:50 +0000)]
move usb driver to target specific modules.mk
SVN-Revision: 32861
Florian Fainelli [Wed, 25 Jul 2012 15:50:29 +0000 (15:50 +0000)]
kmod-r6040 depends on PCI_SUPPORT
SVN-Revision: 32860
Florian Fainelli [Wed, 25 Jul 2012 15:50:26 +0000 (15:50 +0000)]
move mmc driver to target specific modules.mk
SVN-Revision: 32859
projects / openwrt / staging / yousong.git / log