From: Maxim Anisimov Date: Sat, 13 Jan 2018 07:16:20 +0000 (+0300) Subject: ramips: rename TP-Link Archer C20 to TP-Link Archer C20 v1 X-Git-Url: http://git.lede-project.org./?a=commitdiff_plain;h=ff1e89553078cb1f8851276537d1267930d740df;p=openwrt%2Fstaging%2Fstintel.git ramips: rename TP-Link Archer C20 to TP-Link Archer C20 v1 This changes device name from "TP-Link Archer C20" to "TP-Link Archer C20 v1" because of TPLINK released new TP-Link Archer C20 v4. Additionally migration to the generic board detection has been made. Signed-off-by: Maxim Anisimov --- diff --git a/target/linux/ramips/base-files/etc/board.d/01_leds b/target/linux/ramips/base-files/etc/board.d/01_leds index 3e26493e54..37393eeb27 100755 --- a/target/linux/ramips/base-files/etc/board.d/01_leds +++ b/target/linux/ramips/base-files/etc/board.d/01_leds @@ -91,12 +91,6 @@ c108) ucidef_set_led_netdev "lan" "lan" "$boardname:green:lan" "eth0" ucidef_set_led_netdev "modem" "modem" "$boardname:green:modem" "wwan0" ;; -c20) - ucidef_set_led_switch "lan" "lan" "$boardname:blue:lan" "switch0" "0x1e" - ucidef_set_led_switch "wan" "wan" "$boardname:blue:wan" "switch0" "0x01" - set_usb_led "$boardname:blue:usb" - ucidef_set_led_netdev "wlan2g" "wlan2g" "$boardname:blue:wlan2g" "wlan0" - ;; c20i) ucidef_set_led_switch "lan" "lan" "$boardname:blue:lan" "switch0" "0x1e" ucidef_set_led_switch "wan" "wan" "$boardname:blue:wan" "switch0" "0x01" @@ -388,6 +382,12 @@ tl-wr841n-v13) ucidef_set_led_switch "lan4" "lan4" "$boardname:green:lan4" "switch0" "0x10" ucidef_set_led_switch "wan" "wan" "$boardname:green:wan" "switch0" "0x01" ;; +tplink,c20-v1) + ucidef_set_led_switch "lan" "lan" "$boardname:blue:lan" "switch0" "0x1e" + ucidef_set_led_switch "wan" "wan" "$boardname:blue:wan" "switch0" "0x01" + set_usb_led "$boardname:blue:usb" + ucidef_set_led_netdev "wlan2g" "wlan2g" "$boardname:blue:wlan2g" "wlan0" + ;; tplink,tl-mr3420-v5) set_usb_led "$boardname:green:usb" set_wifi_led "$boardname:green:wlan" diff --git a/target/linux/ramips/base-files/etc/board.d/02_network b/target/linux/ramips/base-files/etc/board.d/02_network index 105f5e9e32..a90fe96f91 100755 --- a/target/linux/ramips/base-files/etc/board.d/02_network +++ b/target/linux/ramips/base-files/etc/board.d/02_network @@ -190,8 +190,8 @@ ramips_setup_interfaces() ucidef_add_switch "switch0" \ "1:lan" "2:lan" "3:lan" "4:lan" "0:wan" "6@eth0" ;; - c20|\ - c50) + c50|\ + tplink,c20-v1) ucidef_add_switch "switch0" \ "1:lan:3" "2:lan:4" "3:lan:1" "4:lan:2" "0:wan" "6@eth0" ;; diff --git a/target/linux/ramips/base-files/etc/diag.sh b/target/linux/ramips/base-files/etc/diag.sh index e1d29152f1..df9858cb32 100644 --- a/target/linux/ramips/base-files/etc/diag.sh +++ b/target/linux/ramips/base-files/etc/diag.sh @@ -124,7 +124,6 @@ get_status_led() { w502u) status_led="$boardname:blue:wps" ;; - c20|\ d240|\ dap-1350|\ na930|\ @@ -136,6 +135,7 @@ get_status_led() { rt-n14u|\ rt-n15|\ rt-n56u|\ + tplink,c20-v1|\ wl-330n|\ wl-330n3g|\ wli-tx4-ag300n|\ diff --git a/target/linux/ramips/base-files/lib/ramips.sh b/target/linux/ramips/base-files/lib/ramips.sh index e85b293610..3ba6d0f0f5 100755 --- a/target/linux/ramips/base-files/lib/ramips.sh +++ b/target/linux/ramips/base-files/lib/ramips.sh @@ -85,9 +85,6 @@ ramips_board_detect() { *"C108") name="c108" ;; - *"C20") - name="c20" - ;; *"C20i") name="c20i" ;; diff --git a/target/linux/ramips/base-files/lib/upgrade/platform.sh b/target/linux/ramips/base-files/lib/upgrade/platform.sh index e2ab3a643e..71ad0c1b83 100755 --- a/target/linux/ramips/base-files/lib/upgrade/platform.sh +++ b/target/linux/ramips/base-files/lib/upgrade/platform.sh @@ -237,10 +237,10 @@ platform_check_image() { } return 0 ;; - c20|\ c20i|\ c50|\ mr200|\ + tplink,c20-v1|\ tplink,tl-mr3420-v5|\ tl-wr840n-v4|\ tl-wr840n-v5|\ diff --git a/target/linux/ramips/dts/ArcherC20.dts b/target/linux/ramips/dts/ArcherC20.dts deleted file mode 100644 index f0281c37c3..0000000000 --- a/target/linux/ramips/dts/ArcherC20.dts +++ /dev/null @@ -1,187 +0,0 @@ -/dts-v1/; - -#include "mt7620a.dtsi" - -#include -#include - -/ { - compatible = "tplink,c20", "ralink,mt7620a-soc"; - model = "TP-Link Archer C20"; - - chosen { - bootargs = "console=ttyS0,115200"; - }; - - gpio-leds { - compatible = "gpio-leds"; - - lan { - label = "c20:blue:lan"; - gpios = <&gpio0 1 GPIO_ACTIVE_LOW>; - }; - - power { - label = "c20:blue:power"; - gpios = <&gpio0 7 GPIO_ACTIVE_LOW>; - default-state = "keep"; - }; - - usb { - label = "c20:blue:usb"; - gpios = <&gpio2 4 GPIO_ACTIVE_LOW>; - }; - - wan { - label = "c20:blue:wan"; - gpios = <&gpio0 11 GPIO_ACTIVE_HIGH>; - }; - - wan_orange { - label = "c20:orange:wan"; - gpios = <&gpio0 9 GPIO_ACTIVE_HIGH>; - }; - - wlan5g { - label = "c20:blue:wlan5g"; - gpios = <&gpio0 17 GPIO_ACTIVE_LOW>; - }; - - wlan2g { - label = "c20:blue:wlan2g"; - gpios = <&gpio3 0 GPIO_ACTIVE_LOW>; - }; - - wps { - label = "c20:blue:wps"; - gpios = <&gpio1 15 GPIO_ACTIVE_LOW>; - }; - }; - - gpio-keys-polled { - compatible = "gpio-keys-polled"; - #address-cells = <1>; - #size-cells = <0>; - poll-interval = <20>; - - reset { - label = "reset"; - gpios = <&gpio0 13 GPIO_ACTIVE_LOW>; - linux,code = ; - }; - - rfkill { - label = "rfkill"; - gpios = <&gpio0 2 GPIO_ACTIVE_LOW>; - linux,code = ; - }; }; -}; - -&gpio1 { - status = "okay"; -}; - -&gpio2 { - status = "okay"; -}; - -&gpio3 { - status = "okay"; -}; - -&spi0 { - status = "okay"; - - m25p80@0 { - #address-cells = <1>; - #size-cells = <1>; - compatible = "jedec,spi-nor"; - reg = <0>; - spi-max-frequency = <10000000>; - - partition@0 { - label = "u-boot"; - reg = <0x0 0x20000>; - read-only; - }; - - partition@20000 { - label = "firmware"; - reg = <0x20000 0x7a0000>; - }; - - partition@7c0000 { - label = "config"; - reg = <0x7c0000 0x10000>; - read-only; - }; - - rom: partition@7d0000 { - label = "rom"; - reg = <0x7d0000 0x10000>; - read-only; - }; - - partition@7e0000 { - label = "romfile"; - reg = <0x7e0000 0x10000>; - read-only; - }; - - radio: partition@7f0000 { - label = "radio"; - reg = <0x7f0000 0x10000>; - read-only; - }; - }; -}; - -&pinctrl { - state_default: pinctrl0 { - gpio { - ralink,group = "i2c", "uartf", "wled", "ephy", "spi refclk", "wdt"; - ralink,function = "gpio"; - }; - }; -}; - -ðernet { - pinctrl-names = "default"; - mtd-mac-address = <&rom 0xf100>; - mediatek,portmap = "wllll"; - }; - -&ehci { - status = "okay"; -}; - -&ohci { - status = "okay"; -}; - -&gsw { - mediatek,port4 = "ephy"; -}; - -&wmac { - ralink,mtd-eeprom = <&radio 0>; - mtd-mac-address = <&rom 0xf100>; - mtd-mac-address-increment = <(-2)>; - pinctrl-names = "default"; - pinctrl-0 = <&pa_pins>; -}; - -&pcie { - status = "okay"; - - pcie-bridge { - mt76@0,0 { - reg = <0x0000 0 0 0 0>; - device_type = "pci"; - mediatek,mtd-eeprom = <&radio 32768>; - ieee80211-freq-limit = <5000000 6000000>; - mtd-mac-address = <&rom 0xf100>; - mtd-mac-address-increment = <(-1)>; - }; - }; -}; diff --git a/target/linux/ramips/dts/ArcherC20v1.dts b/target/linux/ramips/dts/ArcherC20v1.dts new file mode 100644 index 0000000000..9d8a2b595c --- /dev/null +++ b/target/linux/ramips/dts/ArcherC20v1.dts @@ -0,0 +1,188 @@ +/dts-v1/; + +#include "mt7620a.dtsi" + +#include +#include + +/ { + compatible = "tplink,c20-v1", "ralink,mt7620a-soc"; + model = "TP-Link Archer C20 v1"; + + chosen { + bootargs = "console=ttyS0,115200"; + }; + + gpio-leds { + compatible = "gpio-leds"; + + lan { + label = "c20-v1:blue:lan"; + gpios = <&gpio0 1 GPIO_ACTIVE_LOW>; + }; + + power { + label = "c20-v1:blue:power"; + gpios = <&gpio0 7 GPIO_ACTIVE_LOW>; + default-state = "keep"; + }; + + usb { + label = "c20-v1:blue:usb"; + gpios = <&gpio2 4 GPIO_ACTIVE_LOW>; + }; + + wan { + label = "c20-v1:blue:wan"; + gpios = <&gpio0 11 GPIO_ACTIVE_HIGH>; + }; + + wan_orange { + label = "c20-v1:orange:wan"; + gpios = <&gpio0 9 GPIO_ACTIVE_HIGH>; + }; + + wlan5g { + label = "c20-v1:blue:wlan5g"; + gpios = <&gpio0 17 GPIO_ACTIVE_LOW>; + }; + + wlan2g { + label = "c20-v1:blue:wlan2g"; + gpios = <&gpio3 0 GPIO_ACTIVE_LOW>; + }; + + wps { + label = "c20-v1:blue:wps"; + gpios = <&gpio1 15 GPIO_ACTIVE_LOW>; + }; + }; + + gpio-keys-polled { + compatible = "gpio-keys-polled"; + #address-cells = <1>; + #size-cells = <0>; + poll-interval = <20>; + + reset { + label = "reset"; + gpios = <&gpio0 13 GPIO_ACTIVE_LOW>; + linux,code = ; + }; + + rfkill { + label = "rfkill"; + gpios = <&gpio0 2 GPIO_ACTIVE_LOW>; + linux,code = ; + }; + }; +}; + +&gpio1 { + status = "okay"; +}; + +&gpio2 { + status = "okay"; +}; + +&gpio3 { + status = "okay"; +}; + +&spi0 { + status = "okay"; + + m25p80@0 { + #address-cells = <1>; + #size-cells = <1>; + compatible = "jedec,spi-nor"; + reg = <0>; + spi-max-frequency = <10000000>; + + partition@0 { + label = "u-boot"; + reg = <0x0 0x20000>; + read-only; + }; + + partition@20000 { + label = "firmware"; + reg = <0x20000 0x7a0000>; + }; + + partition@7c0000 { + label = "config"; + reg = <0x7c0000 0x10000>; + read-only; + }; + + rom: partition@7d0000 { + label = "rom"; + reg = <0x7d0000 0x10000>; + read-only; + }; + + partition@7e0000 { + label = "romfile"; + reg = <0x7e0000 0x10000>; + read-only; + }; + + radio: partition@7f0000 { + label = "radio"; + reg = <0x7f0000 0x10000>; + read-only; + }; + }; +}; + +&pinctrl { + state_default: pinctrl0 { + gpio { + ralink,group = "i2c", "uartf", "wled", "ephy", "spi refclk", "wdt"; + ralink,function = "gpio"; + }; + }; +}; + +ðernet { + pinctrl-names = "default"; + mtd-mac-address = <&rom 0xf100>; + mediatek,portmap = "wllll"; + }; + +&ehci { + status = "okay"; +}; + +&ohci { + status = "okay"; +}; + +&gsw { + mediatek,port4 = "ephy"; +}; + +&wmac { + ralink,mtd-eeprom = <&radio 0>; + mtd-mac-address = <&rom 0xf100>; + mtd-mac-address-increment = <(-2)>; + pinctrl-names = "default"; + pinctrl-0 = <&pa_pins>; +}; + +&pcie { + status = "okay"; + + pcie-bridge { + mt76@0,0 { + reg = <0x0000 0 0 0 0>; + device_type = "pci"; + mediatek,mtd-eeprom = <&radio 0x8000>; + ieee80211-freq-limit = <5000000 6000000>; + mtd-mac-address = <&rom 0xf100>; + mtd-mac-address-increment = <(-1)>; + }; + }; +}; diff --git a/target/linux/ramips/image/mt7620.mk b/target/linux/ramips/image/mt7620.mk index 6f9aa1aa6d..d4c4e719b7 100644 --- a/target/linux/ramips/image/mt7620.mk +++ b/target/linux/ramips/image/mt7620.mk @@ -45,20 +45,6 @@ define Device/Archer IMAGE/sysupgrade.bin := tplink-v2-image -s -e | append-metadata endef -define Device/ArcherC20 - $(Device/Archer) - DTS := ArcherC20 - SUPPORTED_DEVICES := c20 - TPLINK_FLASHLAYOUT := 8Mmtk - TPLINK_HWID := 0xc2000001 - TPLINK_HWREV := 0x44 - TPLINK_HWREVADD := 0x1 - IMAGES += factory.bin - DEVICE_TITLE := TP-Link ArcherC20 - DEVICE_PACKAGES := kmod-usb-core kmod-usb2 kmod-usb-ledtrig-usbport -endef -TARGET_DEVICES += ArcherC20 - define Device/ArcherC20i $(Device/Archer) DTS := ArcherC20i @@ -433,6 +419,20 @@ define Device/tiny-ac endef TARGET_DEVICES += tiny-ac +define Device/tplink_c20-v1 + $(Device/Archer) + DTS := ArcherC20v1 + SUPPORTED_DEVICES := c20v1 + TPLINK_FLASHLAYOUT := 8Mmtk + TPLINK_HWID := 0xc2000001 + TPLINK_HWREV := 0x44 + TPLINK_HWREVADD := 0x1 + IMAGES += factory.bin + DEVICE_TITLE := TP-Link ArcherC20 v1 + DEVICE_PACKAGES := kmod-usb-core kmod-usb2 kmod-usb-ledtrig-usbport +endef +TARGET_DEVICES += tplink_c20-v1 + define Device/vonets_var11n-300 DTS := VAR11N-300 IMAGE_SIZE := $(ralink_default_fw_size_4M)