From: Mauri Sandberg Date: Mon, 31 Jul 2023 12:35:46 +0000 (+0300) Subject: ramips: mt7621: Add DNA Valokuitu Plus EX400 X-Git-Url: http://git.lede-project.org./?a=commitdiff_plain;h=fea2264d9fddc285f724aad04335462807710d61;p=openwrt%2Fstaging%2Fblocktrron.git ramips: mt7621: Add DNA Valokuitu Plus EX400 Specifications: - Device: DNA Valokuitu Plus EX400 - SoC: MT7621A - Flash: 256MB NAND - RAM: 256MB - Ethernet: Built-in, 2 x 1GbE - Wifi: MT7603 2.4 GHz, MT7615 5 GHz (4x internal antennas) - USB: 1x 3.0 - LED: 1x green/red, 1x green - Buttons: Reset MAC addresses: - LAN: u-boot 'ethaddr' (label) - WAN: label + 1 - 2.4 GHz: label + 6 - 5 GHz: label + 7 Serial: There is a black block connector next to the red ethernet connector. It is accessible also through holes in the casing. Pinout (TTL 3.3V) +---+---+ |Tx |Rx | +---+---+ |Vcc|Gnd| +---+---+ Firmware: The vendor firmware is a fork of OpenWrt (Reboot) with a kernel version 4.4.93. The flash is arranged as below and there is a dual boot mechanism alternating between rootfs_0 and rootfs_1. +-------+------+------+-----------+-----------+ | | env1 | env2 | rootfs_0 | rootfs_1 | | +------+------+-----------+-----------+ | | UBI volumes | +-------+-------------------------------------+ |U-Boot | UBI | +-------+-------------------------------------+ |mtd0 | mtd1 | +-------+-------------------------------------+ | NAND | +---------------------------------------------+ In OpenWrt rootfs_0 will be used as a boot partition that will contain the kernel and the dtb. The squashfs rootfs and overlay are standard OpenWrt behaviour. +-------+------+------+-----------+--------+------------+ | | env1 | env2 | rootfs_0 | rootfs | rootfs_data| | +------+------+-----------+--------+------------+ | | UBI volumes | +-------+-----------------------------------------------+ |U-Boot | UBI | +-------+-----------------------------------------------+ |mtd0 | mtd1 | +-------+-----------------------------------------------+ | NAND | +-------------------------------------------------------+ U-boot: With proper serial access booting can be halted to U-boot by pressing any key. TFTP and flash writes are available, but only the first one has been tested. NOTE: Recovery mode can be accessed by holding down the reset button while powering on the device. The led 'Update' will show a solid green light once ready. A web server will be running at 192.168.1.1:80 and it will allow flashing a firmware package. You can cycle between rootfs_0 and rootfs_1 by pressing the reset button once. Root password: With the vendor web UI create a backup of your settings and download the archive to your computer. Within the archive in the file /etc/shadow replace the password hash for root with that of a password you know. Restore the configuration with the vendor web UI and you will have changed the root password. SSH access: You might need to enable the SSH service for LAN interface as by default it's enabled for WAN only. Installing OpenWrt: With the vendor web UI install the OpenWrt factory image. Alternatively, ssh to the device and use sysupgrade -n from cli. Finalize by installing the OpenWrt sysupgrade image to get a fully functioning system. Reverting to the vendor firmware: Boot with OpenWrt initramfs image - Remove volumes rootfs_0, rootfs and rootfs_data and create vendor volumes. ubirmvol /dev/ubi0 -n 2 ubirmvol /dev/ubi0 -n 3 ubirmvol /dev/ubi0 -n 4 ubimkvol /dev/ubi0 -N rootfs_0 -S 990 ubimkvol /dev/ubi0 -N rootfs_1 -S 990 Power off and enter to the U-boot recovery to install the vendor firmware. Known issues: - MACs for wifi are stored in currently unknown place but it seems to persist over power-off. They might be stored on the chip. Signed-off-by: Mauri Sandberg [rmilecki: try NVMEM for MACs] Signed-off-by: Rafał Miłecki --- diff --git a/package/boot/uboot-envtools/files/ramips b/package/boot/uboot-envtools/files/ramips index cca394a03b..97e9fc2b1c 100644 --- a/package/boot/uboot-envtools/files/ramips +++ b/package/boot/uboot-envtools/files/ramips @@ -146,6 +146,10 @@ xiaomi,mi-router-cr6608|\ xiaomi,mi-router-cr6609) ubootenv_add_uci_config "/dev/mtd1" "0x0" "0x10000" "0x20000" ;; +dna,valokuitu-plus-ex400) + ubootenv_add_uci_config "/dev/ubi0_0" "0x0" "0x1f000" "0x1f000" "1" + ubootenv_add_uci_config "/dev/ubi0_1" "0x0" "0x1f000" "0x1f000" "1" + ;; netgear,wax214v2) ubootenv_add_uci_config "/dev/mtd1" "0x0" "0x20000" "0x20000" ubootenv_add_uci_sys_config "/dev/mtd1" "0x20000" "0x8000" "0x20000" diff --git a/target/linux/ramips/dts/mt7621_dna_valokuitu-plus-ex400.dts b/target/linux/ramips/dts/mt7621_dna_valokuitu-plus-ex400.dts new file mode 100644 index 0000000000..98b2bbf7b6 --- /dev/null +++ b/target/linux/ramips/dts/mt7621_dna_valokuitu-plus-ex400.dts @@ -0,0 +1,130 @@ +// SPDX-License-Identifier: GPL-2.0-or-later OR MIT + +#include "mt7621.dtsi" + +#include +#include +#include + +/ { + compatible = "dna,valokuitu-plus-ex400", "mediatek,mt7621-soc"; + model = "DNA Valokuitu Plus EX400"; + + aliases { + ethernet0 = &gmac0; + label-mac-device = &gmac0; + led-boot = &led_status_red; + led-failsafe = &led_status_red; + led-running = &led_status_green; + led-upgrade = &led_update_green; + }; + + chosen { + bootargs-override = "console=ttyS0,115200 rootfstype=squashfs,jffs2"; + }; + + keys { + compatible = "gpio-keys"; + + reset { + label = "reset"; + gpios = <&gpio 18 GPIO_ACTIVE_LOW>; + linux,code = ; + }; + }; + + leds { + compatible = "gpio-leds"; + + led_status_green: led-0 { + color = ; + function = LED_FUNCTION_STATUS; + gpios = <&gpio 8 GPIO_ACTIVE_LOW>; + }; + + led_status_red: led-1 { + color = ; + function = LED_FUNCTION_STATUS; + gpios = <&gpio 11 GPIO_ACTIVE_HIGH>; + }; + + led_update_green: led-2 { + color = ; + function = LED_FUNCTION_PROGRAMMING; + gpios = <&gpio 12 GPIO_ACTIVE_LOW>; + }; + }; +}; + +&pcie { + status = "okay"; +}; + +&nand { + status = "okay"; + + partitions { + compatible = "fixed-partitions"; + #address-cells = <1>; + #size-cells = <1>; + + partition@0 { + reg = <0x00 0x100000>; + label = "uboot"; + read-only; + }; + + partition@100000 { + reg = <0x100000 0xff00000>; + label = "ubi"; + + volumes { + ubi-volume-env1 { + volname = "env1"; + + nvmem-layout { + compatible = "u-boot,env"; + + ethaddr: ethaddr { + #nvmem-cell-cells = <1>; + }; + }; + }; + }; + }; + }; +}; + +&gmac1 { + label = "wan"; + phy-handle = <ðphy0>; + nvmem-cells = <ðaddr 1>; + nvmem-cell-names = "mac-address"; + status = "okay"; +}; + +&i2c { + status = "okay"; +}; + +ðphy0 { + /delete-property/ interrupts; +}; + +&state_default { + gpio { + groups = "uart2", "uart3"; + function = "gpio"; + }; +}; + +&switch0 { + ports { + port@1 { + label = "lan"; + nvmem-cells = <ðaddr 0>; + nvmem-cell-names = "mac-address"; + status = "okay"; + }; + }; +}; diff --git a/target/linux/ramips/image/mt7621.mk b/target/linux/ramips/image/mt7621.mk index 18dbbcadf3..bf700674ef 100644 --- a/target/linux/ramips/image/mt7621.mk +++ b/target/linux/ramips/image/mt7621.mk @@ -36,6 +36,68 @@ define Build/arcadyan-trx rm $@.hsqs $@.tail endef +define Build/dna-header + BC='$(STAGING_DIR_HOST)/bin/bc' ;\ + ubifsofs="1024" ;\ + ubifs="$$(stat -c%s $@)" ;\ + pkginfoofs="$$(echo $${ubifsofs} + $${ubifs} | $${BC})" ;\ + pkginfo="0" ;\ + scrofs="$$(echo $${pkginfoofs} + $${pkginfo} | $${BC})" ;\ + scr="0" ;\ + sigofs="$$(echo $${scrofs} + $${scr} | $${BC})" ;\ + sig="0" ;\ + md5ofs="$$(echo $${sigofs} + $${sig} | $${BC})" ;\ + md5="32" ;\ + size="$$(echo $${md5ofs} + $${md5} | $${BC})" ;\ + echo "IntenoIopY" > $@.tmp ;\ + echo "version 5" >> $@.tmp ;\ + echo "integrity MD5SUM" >> $@.tmp ;\ + echo "board EX400" >> $@.tmp ;\ + echo "chip 7621" >> $@.tmp ;\ + echo "arch all mipsel_1004kc" >> $@.tmp ;\ + echo "model EX400" >> $@.tmp ;\ + echo "release EX400-X-DNA-4.3.6.100-R-210518_0935" >> $@.tmp ;\ + echo "customer DNA" >> $@.tmp ;\ + echo "ubifsofs $${ubifsofs}" >> $@.tmp ;\ + echo "ubifs $${ubifs}" >> $@.tmp ;\ + echo "pkginfoofs $${pkginfoofs}" >> $@.tmp ;\ + echo "pkginfo $${pkginfo}" >> $@.tmp ;\ + echo "scrofs $${scrofs}" >> $@.tmp ;\ + echo "scr $${scr}" >> $@.tmp ;\ + echo "sigofs $${sigofs}" >> $@.tmp ;\ + echo "sig $${sig}" >> $@.tmp ;\ + echo "md5ofs $${md5ofs}" >> $@.tmp ;\ + echo "md5 $${md5}" >> $@.tmp ;\ + echo "size $${size}" >> $@.tmp + + dd if=$@.tmp of=$@.tmp2 bs=1024 count=1 conv=sync + cat $@.tmp2 $@ > $@.tmp + rm $@.tmp2 + mv $@.tmp $@ +endef + +define Build/dna-bootfs + mkdir -p $@.ubifs-dir/boot + + # populate the boot fs with the dtb and with either initramfs kernel or + # the normal kernel + $(CP) $(KDIR)/image-$(firstword $(DEVICE_DTS)).dtb $@.ubifs-dir/boot/dtb + + $(if $(findstring with-initrd,$(word 1,$(1))),\ + ( \ + $(CP) $@ $@.ubifs-dir/boot/uImage \ + ) , \ + ( \ + $(CP) $(IMAGE_KERNEL) $@.ubifs-dir/boot/uImage \ + ) \ + ) + + # create ubifs + $(STAGING_DIR_HOST)/bin/mkfs.ubifs ${MKUBIFS_OPTS} -r $@.ubifs-dir/ -o $@.new + rm -rf $@.ubifs-dir + mv $@.new $@ +endef + define Build/gemtek-trailer printf "%s%08X" ".GEMTEK." "$$(cksum $@ | cut -d ' ' -f1)" >> $@ endef @@ -103,6 +165,10 @@ define Build/iodata-mstc-header2 mv $@.new $@ endef +define Build/kernel-initramfs-bin + $(CP) $(KDIR)/vmlinux-initramfs $@ +endef + define Build/znet-header $(eval version=$(word 1,$(1))) $(eval magic=$(if $(word 2,$(1)),$(word 2,$(1)),ZNET)) @@ -988,6 +1054,27 @@ define Device/d-team_pbr-m1 endef TARGET_DEVICES += d-team_pbr-m1 +define Device/dna_valokuitu-plus-ex400 + $(Device/dsa-migration) + IMAGE_SIZE := 117m + PAGESIZE := 2048 + MKUBIFS_OPTS := --min-io-size=$$(PAGESIZE) --leb-size=124KiB --max-leb-cnt=96 \ + --log-lebs=2 --space-fixup --squash-uids + DEVICE_VENDOR := DNA + DEVICE_MODEL := Valokuitu Plus EX400 + KERNEL := kernel-bin | lzma | uImage lzma + KERNEL_INITRAMFS := kernel-bin | append-dtb | lzma | uImage lzma + IMAGES := factory.bin sysupgrade.tar + IMAGE/factory.bin := kernel-initramfs-bin | lzma | uImage lzma | \ + dna-bootfs with-initrd | dna-header | \ + append-md5sum-ascii-salted + IMAGE/sysupgrade.tar := dna-bootfs | sysupgrade-tar kernel=$$$$@ | check-size | \ + append-metadata + DEVICE_IMG_NAME = $$(DEVICE_IMG_PREFIX)-$$(2) + DEVICE_PACKAGES := kmod-mt7603 kmod-mt7615-firmware kmod-usb3 +endef +TARGET_DEVICES += dna_valokuitu-plus-ex400 + define Device/edimax_ra21s $(Device/dsa-migration) $(Device/uimage-lzma-loader) diff --git a/target/linux/ramips/mt7621/base-files/etc/board.d/02_network b/target/linux/ramips/mt7621/base-files/etc/board.d/02_network index b7e3a49b43..f251daddd5 100644 --- a/target/linux/ramips/mt7621/base-files/etc/board.d/02_network +++ b/target/linux/ramips/mt7621/base-files/etc/board.d/02_network @@ -67,6 +67,7 @@ ramips_setup_interfaces() ucidef_set_interface_lan "lan" ;; asiarf,ap7621-001|\ + dna,valokuitu-plus-ex400|\ humax,e10|\ keenetic,kn-3510|\ openfi,5pro|\ diff --git a/target/linux/ramips/mt7621/base-files/etc/init.d/bootcount b/target/linux/ramips/mt7621/base-files/etc/init.d/bootcount index 06846cd4ca..b83223e7dd 100755 --- a/target/linux/ramips/mt7621/base-files/etc/init.d/bootcount +++ b/target/linux/ramips/mt7621/base-files/etc/init.d/bootcount @@ -32,6 +32,10 @@ boot() { samknows,whitebox-v8) fw_setenv bootcount 0 ;; + dna,valokuitu-plus-ex400) + fw_setenv boot_cnt_primary 0 + fw_setenv boot_cnt_alt 0 + ;; zyxel,lte3301-plus) [ $(printf %d $(fw_printenv -n DebugFlag)) -gt 0 ] || fw_setenv DebugFlag 1 [ $(printf %d $(fw_printenv -n Image1Stable)) -gt 0 ] || fw_setenv Image1Stable 1 diff --git a/target/linux/ramips/mt7621/base-files/lib/upgrade/dna.sh b/target/linux/ramips/mt7621/base-files/lib/upgrade/dna.sh new file mode 100644 index 0000000000..d699516ff6 --- /dev/null +++ b/target/linux/ramips/mt7621/base-files/lib/upgrade/dna.sh @@ -0,0 +1,44 @@ +# +# Copyright (C) 2023 Mauri Sandberg +# + +# The vendor UBI is split in volumes 0-3. Volumes 0 and 1 contain U-Boot +# environments env1 and env2, respectively. The vendor root file systems +# are in volumes 2 (rootfs_0) and 3 (rootfs_1). Drop the two roots and +# explicitly use rootfs_0 as a boot partition that contains the dtb and the +# OpenWrt kernel. This is because the vendor U-Boot expects to find them there. +# Then continue upgrade with the default method - a SquashFS rootfs will be +# installed and the rest of UBI will be used as an overlay. + +# The 'kernel' inside the sysupgrage.tar is an UBIFS image that contains +# /boot/dtb and /boot/kernel. The 'root' is an OpenWrt SquashFS root + +. /lib/functions.sh +. /lib/upgrade/nand.sh + +dna_do_upgrade () { + tar -xaf $1 + + # get the size of the new bootfs + local _bootfs_size=$(wc -c < ./sysupgrade-dna_valokuitu-plus-ex400/kernel) + [ -n "$_bootfs_size" -a "$_bootfs_size" -gt "0" ] || nand_do_upgrade_failed + + # remove existing rootfses and recreate rootfs_0 + ubirmvol /dev/ubi0 --name=rootfs_0 > /dev/null 2>&1 + ubirmvol /dev/ubi0 --name=rootfs_1 > /dev/null 2>&1 + ubirmvol /dev/ubi0 --name=rootfs > /dev/null 2>&1 + ubirmvol /dev/ubi0 --name=rootfs_data > /dev/null 2>&1 + ubimkvol /dev/ubi0 --type=static --size=${_bootfs_size} --name=rootfs_0 + + # update the rootfs_0 contents + local _kern_ubivol=$( nand_find_volume "ubi0" "rootfs_0" ) + ubiupdatevol /dev/${_kern_ubivol} sysupgrade-dna_valokuitu-plus-ex400/kernel + + fw_setenv root_vol rootfs_0 + fw_setenv boot_cnt_primary 0 + fw_setenv boot_cnt_alt 0 + + # proceed to upgrade the default way + CI_KERNPART=none + nand_do_upgrade "$1" +} diff --git a/target/linux/ramips/mt7621/base-files/lib/upgrade/platform.sh b/target/linux/ramips/mt7621/base-files/lib/upgrade/platform.sh index bad7e30ca6..f0d41b0914 100755 --- a/target/linux/ramips/mt7621/base-files/lib/upgrade/platform.sh +++ b/target/linux/ramips/mt7621/base-files/lib/upgrade/platform.sh @@ -150,6 +150,9 @@ platform_do_upgrade() { buffalo,wsr-2533dhpls) buffalo_do_upgrade "$1" ;; + dna,valokuitu-plus-ex400) + dna_do_upgrade "$1" + ;; elecom,wrc-x1800gs) [ "$(fw_printenv -n bootmenu_delay)" != "0" ] || \ fw_setenv bootmenu_delay 3