From: Hauke Mehrtens Date: Sun, 25 Oct 2015 16:43:14 +0000 (+0000) Subject: bcm53xx: add support basic for kernel 4.3 X-Git-Url: http://git.lede-project.org./?a=commitdiff_plain;h=fa4395db04e20e5e50b63cdec8b876e22d7e118f;p=openwrt%2Fstaging%2Fkaloz.git bcm53xx: add support basic for kernel 4.3 The files directory is now split up into the files which are needed for every kernel version and the files only needed by kernel 4.1. The files in files-4.1 are already merged into mainline kernel 4.3. This patch only removed patches which were merged into mainline kernel 4.3. Signed-off-by: Hauke Mehrtens SVN-Revision: 47251 --- diff --git a/target/linux/bcm53xx/config-4.3 b/target/linux/bcm53xx/config-4.3 new file mode 100644 index 0000000000..73c8062fa9 --- /dev/null +++ b/target/linux/bcm53xx/config-4.3 @@ -0,0 +1,318 @@ +CONFIG_ALIGNMENT_TRAP=y +CONFIG_ARCH_BCM=y +# CONFIG_ARCH_BCM_21664 is not set +# CONFIG_ARCH_BCM_281XX is not set +CONFIG_ARCH_BCM_5301X=y +# CONFIG_ARCH_BCM_63XX is not set +# CONFIG_ARCH_BCM_CYGNUS is not set +CONFIG_ARCH_BCM_IPROC=y +# CONFIG_ARCH_BRCMSTB is not set +CONFIG_ARCH_HAS_ATOMIC64_DEC_IF_POSITIVE=y +CONFIG_ARCH_HAS_ELF_RANDOMIZE=y +CONFIG_ARCH_HAS_GCOV_PROFILE_ALL=y +CONFIG_ARCH_HAS_SG_CHAIN=y +CONFIG_ARCH_HAS_TICK_BROADCAST=y +CONFIG_ARCH_HAVE_CUSTOM_GPIO_H=y +CONFIG_ARCH_HIBERNATION_POSSIBLE=y +CONFIG_ARCH_MIGHT_HAVE_PC_PARPORT=y +CONFIG_ARCH_MULTIPLATFORM=y +# CONFIG_ARCH_MULTI_CPU_AUTO is not set +CONFIG_ARCH_MULTI_V6_V7=y +CONFIG_ARCH_MULTI_V7=y +CONFIG_ARCH_NR_GPIO=0 +CONFIG_ARCH_REQUIRE_GPIOLIB=y +# CONFIG_ARCH_SELECT_MEMORY_MODEL is not set +# CONFIG_ARCH_SPARSEMEM_DEFAULT is not set +CONFIG_ARCH_SUPPORTS_ATOMIC_RMW=y +CONFIG_ARCH_SUPPORTS_UPROBES=y +CONFIG_ARCH_SUSPEND_POSSIBLE=y +CONFIG_ARCH_USE_BUILTIN_BSWAP=y +CONFIG_ARCH_USE_CMPXCHG_LOCKREF=y +CONFIG_ARCH_WANT_GENERAL_HUGETLB=y +CONFIG_ARCH_WANT_IPC_PARSE_VERSION=y +CONFIG_ARCH_WANT_OPTIONAL_GPIOLIB=y +CONFIG_ARM=y +CONFIG_ARM_AMBA=y +CONFIG_ARM_APPENDED_DTB=y +# CONFIG_ARM_ATAG_DTB_COMPAT is not set +# CONFIG_ARM_CPU_SUSPEND is not set +CONFIG_ARM_ERRATA_754322=y +CONFIG_ARM_ERRATA_764369=y +CONFIG_ARM_ERRATA_775420=y +CONFIG_ARM_ERRATA_798181=y +CONFIG_ARM_GIC=y +CONFIG_ARM_GLOBAL_TIMER=y +CONFIG_ARM_HAS_SG_CHAIN=y +CONFIG_ARM_HEAVY_MB=y +CONFIG_ARM_L1_CACHE_SHIFT=6 +CONFIG_ARM_L1_CACHE_SHIFT_6=y +# CONFIG_ARM_LPAE is not set +CONFIG_ARM_PATCH_PHYS_VIRT=y +# CONFIG_ARM_SP805_WATCHDOG is not set +CONFIG_ARM_THUMB=y +# CONFIG_ARM_THUMBEE is not set +CONFIG_ARM_VIRT_EXT=y +CONFIG_ATAGS=y +CONFIG_AUTO_ZRELADDR=y +CONFIG_B53=y +# CONFIG_B53_MMAP_DRIVER is not set +# CONFIG_B53_PHY_DRIVER is not set +CONFIG_B53_SRAB_DRIVER=y +CONFIG_BCM47XX_NVRAM=y +CONFIG_BCM47XX_SPROM=y +CONFIG_BCM47XX_WDT=y +CONFIG_BCMA=y +CONFIG_BCMA_BLOCKIO=y +CONFIG_BCMA_DEBUG=y +CONFIG_BCMA_DRIVER_GMAC_CMN=y +CONFIG_BCMA_DRIVER_GPIO=y +CONFIG_BCMA_DRIVER_PCI=y +CONFIG_BCMA_HOST_PCI=y +CONFIG_BCMA_HOST_PCI_POSSIBLE=y +CONFIG_BCMA_HOST_SOC=y +CONFIG_BGMAC=y +CONFIG_BOUNCE=y +CONFIG_CACHE_L2X0=y +CONFIG_CC_OPTIMIZE_FOR_SIZE=y +CONFIG_CLKDEV_LOOKUP=y +CONFIG_CLKSRC_ARM_GLOBAL_TIMER_SCHED_CLOCK=y +CONFIG_CLKSRC_MMIO=y +CONFIG_CLKSRC_OF=y +CONFIG_CLONE_BACKWARDS=y +CONFIG_COMMON_CLK=y +CONFIG_CPU_32v6K=y +CONFIG_CPU_32v7=y +CONFIG_CPU_ABRT_EV7=y +# CONFIG_CPU_BPREDICT_DISABLE is not set +CONFIG_CPU_CACHE_V7=y +CONFIG_CPU_CACHE_VIPT=y +CONFIG_CPU_COPY_V6=y +CONFIG_CPU_CP15=y +CONFIG_CPU_CP15_MMU=y +CONFIG_CPU_HAS_ASID=y +# CONFIG_CPU_ICACHE_DISABLE is not set +CONFIG_CPU_PABRT_V7=y +CONFIG_CPU_RMAP=y +CONFIG_CPU_TLB_V7=y +CONFIG_CPU_V7=y +CONFIG_CRC16=y +CONFIG_CRYPTO_DEFLATE=y +# CONFIG_CRYPTO_JITTERENTROPY is not set +CONFIG_CRYPTO_LZO=y +CONFIG_CRYPTO_RNG2=y +CONFIG_CRYPTO_WORKQUEUE=y +CONFIG_CRYPTO_XZ=y +CONFIG_DCACHE_WORD_ACCESS=y +CONFIG_DEBUG_BCM_5301X=y +CONFIG_DEBUG_INFO=y +CONFIG_DEBUG_LL=y +CONFIG_DEBUG_LL_INCLUDE="debug/8250.S" +CONFIG_DEBUG_UART_8250=y +# CONFIG_DEBUG_UART_8250_FLOW_CONTROL is not set +CONFIG_DEBUG_UART_8250_SHIFT=0 +CONFIG_DEBUG_UART_PHYS=0x18000300 +CONFIG_DEBUG_UART_VIRT=0xf1000300 +CONFIG_DEBUG_UNCOMPRESS=y +CONFIG_DEBUG_USER=y +CONFIG_DTC=y +CONFIG_EARLY_PRINTK=y +CONFIG_EDAC_ATOMIC_SCRUB=y +CONFIG_EDAC_SUPPORT=y +CONFIG_FIXED_PHY=y +CONFIG_FIX_EARLYCON_MEM=y +CONFIG_FRAME_POINTER=y +CONFIG_GENERIC_ALLOCATOR=y +CONFIG_GENERIC_BUG=y +CONFIG_GENERIC_CLOCKEVENTS=y +CONFIG_GENERIC_CLOCKEVENTS_BROADCAST=y +CONFIG_GENERIC_IDLE_POLL_SETUP=y +CONFIG_GENERIC_IO=y +CONFIG_GENERIC_IRQ_SHOW=y +CONFIG_GENERIC_IRQ_SHOW_LEVEL=y +CONFIG_GENERIC_PCI_IOMAP=y +CONFIG_GENERIC_PINCONF=y +CONFIG_GENERIC_SCHED_CLOCK=y +CONFIG_GENERIC_SMP_IDLE_THREAD=y +CONFIG_GENERIC_STRNCPY_FROM_USER=y +CONFIG_GENERIC_STRNLEN_USER=y +CONFIG_GPIOLIB=y +CONFIG_GPIOLIB_IRQCHIP=y +CONFIG_GPIO_74X164=y +CONFIG_GPIO_DEVRES=y +CONFIG_GPIO_SYSFS=y +CONFIG_HANDLE_DOMAIN_IRQ=y +CONFIG_HARDIRQS_SW_RESEND=y +CONFIG_HAS_DMA=y +CONFIG_HAS_IOMEM=y +CONFIG_HAS_IOPORT_MAP=y +# CONFIG_HAVE_64BIT_ALIGNED_ACCESS is not set +CONFIG_HAVE_ARCH_AUDITSYSCALL=y +CONFIG_HAVE_ARCH_BITREVERSE=y +CONFIG_HAVE_ARCH_JUMP_LABEL=y +CONFIG_HAVE_ARCH_KGDB=y +CONFIG_HAVE_ARCH_PFN_VALID=y +CONFIG_HAVE_ARCH_SECCOMP_FILTER=y +CONFIG_HAVE_ARCH_TRACEHOOK=y +CONFIG_HAVE_ARM_SCU=y +CONFIG_HAVE_ARM_TWD=y +# CONFIG_HAVE_BOOTMEM_INFO_NODE is not set +CONFIG_HAVE_BPF_JIT=y +CONFIG_HAVE_CC_STACKPROTECTOR=y +CONFIG_HAVE_CLK=y +CONFIG_HAVE_CLK_PREPARE=y +CONFIG_HAVE_CONTEXT_TRACKING=y +CONFIG_HAVE_C_RECORDMCOUNT=y +CONFIG_HAVE_DEBUG_KMEMLEAK=y +CONFIG_HAVE_DMA_API_DEBUG=y +CONFIG_HAVE_DMA_ATTRS=y +CONFIG_HAVE_DMA_CONTIGUOUS=y +CONFIG_HAVE_DYNAMIC_FTRACE=y +CONFIG_HAVE_EFFICIENT_UNALIGNED_ACCESS=y +CONFIG_HAVE_FTRACE_MCOUNT_RECORD=y +CONFIG_HAVE_FUNCTION_GRAPH_TRACER=y +CONFIG_HAVE_FUNCTION_TRACER=y +CONFIG_HAVE_GENERIC_DMA_COHERENT=y +CONFIG_HAVE_IDE=y +CONFIG_HAVE_IRQ_TIME_ACCOUNTING=y +CONFIG_HAVE_KERNEL_GZIP=y +CONFIG_HAVE_KERNEL_LZ4=y +CONFIG_HAVE_KERNEL_LZMA=y +CONFIG_HAVE_KERNEL_LZO=y +CONFIG_HAVE_KERNEL_XZ=y +CONFIG_HAVE_MEMBLOCK=y +CONFIG_HAVE_MOD_ARCH_SPECIFIC=y +CONFIG_HAVE_NET_DSA=y +CONFIG_HAVE_OPROFILE=y +CONFIG_HAVE_OPTPROBES=y +CONFIG_HAVE_PERF_EVENTS=y +CONFIG_HAVE_PERF_REGS=y +CONFIG_HAVE_PERF_USER_STACK_DUMP=y +CONFIG_HAVE_PROC_CPU=y +CONFIG_HAVE_REGS_AND_STACK_ACCESS_API=y +CONFIG_HAVE_SMP=y +CONFIG_HAVE_SYSCALL_TRACEPOINTS=y +CONFIG_HAVE_UID16=y +CONFIG_HAVE_VIRT_CPU_ACCOUNTING_GEN=y +CONFIG_HIGHMEM=y +# CONFIG_HIGHPTE is not set +CONFIG_HZ_FIXED=0 +CONFIG_HZ_PERIODIC=y +CONFIG_INITRAMFS_SOURCE="" +CONFIG_IOMMU_HELPER=y +CONFIG_IRQCHIP=y +CONFIG_IRQ_DOMAIN=y +CONFIG_IRQ_DOMAIN_HIERARCHY=y +CONFIG_IRQ_FORCED_THREADING=y +CONFIG_IRQ_WORK=y +CONFIG_LIBFDT=y +CONFIG_LOCK_SPIN_ON_OWNER=y +CONFIG_LZO_COMPRESS=y +CONFIG_LZO_DECOMPRESS=y +CONFIG_MAC80211_STA_HASH_MAX_SIZE=0 +CONFIG_MDIO_BOARDINFO=y +CONFIG_MIGHT_HAVE_CACHE_L2X0=y +CONFIG_MIGHT_HAVE_PCI=y +CONFIG_MODULES_USE_ELF_REL=y +CONFIG_MTD_BCM47XX_PARTS=y +CONFIG_MTD_NAND=y +CONFIG_MTD_NAND_BRCMNAND=y +CONFIG_MTD_NAND_ECC=y +# CONFIG_MTD_PHYSMAP_OF is not set +CONFIG_MTD_SPI_BCM53XXSPIFLASH=y +CONFIG_MTD_SPI_NOR=y +CONFIG_MTD_UBI=y +CONFIG_MTD_UBI_BEB_LIMIT=20 +CONFIG_MTD_UBI_BLOCK=y +# CONFIG_MTD_UBI_FASTMAP is not set +# CONFIG_MTD_UBI_GLUEBI is not set +CONFIG_MTD_UBI_WL_THRESHOLD=4096 +CONFIG_MULTI_IRQ_HANDLER=y +CONFIG_MUTEX_SPIN_ON_OWNER=y +CONFIG_NEED_DMA_MAP_STATE=y +CONFIG_NET_FLOW_LIMIT=y +CONFIG_NO_BOOTMEM=y +CONFIG_NR_CPUS=2 +CONFIG_OF=y +CONFIG_OF_ADDRESS=y +CONFIG_OF_ADDRESS_PCI=y +CONFIG_OF_EARLY_FLATTREE=y +CONFIG_OF_FLATTREE=y +CONFIG_OF_GPIO=y +CONFIG_OF_IRQ=y +CONFIG_OF_MDIO=y +CONFIG_OF_MTD=y +CONFIG_OF_NET=y +CONFIG_OF_PCI=y +CONFIG_OF_PCI_IRQ=y +CONFIG_OF_RESERVED_MEM=y +CONFIG_OLD_SIGACTION=y +CONFIG_OLD_SIGSUSPEND3=y +CONFIG_OUTER_CACHE=y +CONFIG_OUTER_CACHE_SYNC=y +CONFIG_PAGEFLAGS_EXTENDED=y +CONFIG_PAGE_OFFSET=0xC0000000 +CONFIG_PCI=y +CONFIG_PCIE_IPROC=y +CONFIG_PCIE_IPROC_BCMA=y +# CONFIG_PCIE_IPROC_PLATFORM is not set +CONFIG_PCI_DOMAINS=y +CONFIG_PCI_DOMAINS_GENERIC=y +CONFIG_PERF_USE_VMALLOC=y +CONFIG_PGTABLE_LEVELS=2 +CONFIG_PHYLIB=y +CONFIG_PINCTRL=y +# CONFIG_PL310_ERRATA_588369 is not set +CONFIG_PL310_ERRATA_727915=y +CONFIG_PL310_ERRATA_753970=y +CONFIG_PL310_ERRATA_769419=y +CONFIG_RCU_STALL_COMMON=y +CONFIG_RFS_ACCEL=y +CONFIG_RPS=y +CONFIG_RWSEM_SPIN_ON_OWNER=y +CONFIG_RWSEM_XCHGADD_ALGORITHM=y +CONFIG_SCHED_HRTICK=y +# CONFIG_SCHED_INFO is not set +# CONFIG_SCSI_DMA is not set +# CONFIG_SERIAL_AMBA_PL010 is not set +# CONFIG_SERIAL_AMBA_PL011 is not set +CONFIG_SERIAL_OF_PLATFORM=y +# CONFIG_SG_SPLIT is not set +CONFIG_SMP=y +CONFIG_SMP_ON_UP=y +CONFIG_SPARSE_IRQ=y +CONFIG_SPI=y +CONFIG_SPI_BCM53XX=y +CONFIG_SPI_BITBANG=y +CONFIG_SPI_GPIO=y +CONFIG_SPI_MASTER=y +CONFIG_SRCU=y +CONFIG_STOP_MACHINE=y +# CONFIG_SUNXI_SRAM is not set +CONFIG_SWCONFIG=y +CONFIG_SWIOTLB=y +CONFIG_SWP_EMULATE=y +# CONFIG_SYSTEM_DATA_VERIFICATION is not set +CONFIG_SYS_SUPPORTS_APM_EMULATION=y +# CONFIG_THUMB2_KERNEL is not set +CONFIG_TICK_CPU_ACCOUNTING=y +CONFIG_TREE_RCU=y +CONFIG_UBIFS_FS=y +# CONFIG_UBIFS_FS_ADVANCED_COMPR is not set +CONFIG_UBIFS_FS_LZO=y +CONFIG_UBIFS_FS_XZ=y +CONFIG_UBIFS_FS_ZLIB=y +CONFIG_UID16=y +CONFIG_UNCOMPRESS_INCLUDE="debug/uncompress.h" +CONFIG_USB_SUPPORT=y +CONFIG_USE_OF=y +CONFIG_VECTORS_BASE=0xffff0000 +# CONFIG_VFP is not set +CONFIG_WATCHDOG_CORE=y +CONFIG_XPS=y +CONFIG_XZ_DEC_ARM=y +CONFIG_XZ_DEC_BCJ=y +CONFIG_ZBOOT_ROM_BSS=0x0 +CONFIG_ZBOOT_ROM_TEXT=0x0 +CONFIG_ZLIB_DEFLATE=y +CONFIG_ZLIB_INFLATE=y +CONFIG_ZONE_DMA_FLAG=0 diff --git a/target/linux/bcm53xx/files-4.1/drivers/firmware/broadcom/Kconfig b/target/linux/bcm53xx/files-4.1/drivers/firmware/broadcom/Kconfig new file mode 100644 index 0000000000..6bed119930 --- /dev/null +++ b/target/linux/bcm53xx/files-4.1/drivers/firmware/broadcom/Kconfig @@ -0,0 +1,11 @@ +config BCM47XX_NVRAM + bool "Broadcom NVRAM driver" + depends on BCM47XX || ARCH_BCM_5301X + help + Broadcom home routers contain flash partition called "nvram" with all + important hardware configuration as well as some minor user setup. + NVRAM partition contains a text-like data representing name=value + pairs. + This driver provides an easy way to get value of requested parameter. + It simply reads content of NVRAM and parses it. It doesn't control any + hardware part itself. diff --git a/target/linux/bcm53xx/files-4.1/drivers/firmware/broadcom/Makefile b/target/linux/bcm53xx/files-4.1/drivers/firmware/broadcom/Makefile new file mode 100644 index 0000000000..d0e683583c --- /dev/null +++ b/target/linux/bcm53xx/files-4.1/drivers/firmware/broadcom/Makefile @@ -0,0 +1 @@ +obj-$(CONFIG_BCM47XX_NVRAM) += bcm47xx_nvram.o diff --git a/target/linux/bcm53xx/files-4.1/drivers/firmware/broadcom/bcm47xx_nvram.c b/target/linux/bcm53xx/files-4.1/drivers/firmware/broadcom/bcm47xx_nvram.c new file mode 100644 index 0000000000..87add3fdce --- /dev/null +++ b/target/linux/bcm53xx/files-4.1/drivers/firmware/broadcom/bcm47xx_nvram.c @@ -0,0 +1,248 @@ +/* + * BCM947xx nvram variable access + * + * Copyright (C) 2005 Broadcom Corporation + * Copyright (C) 2006 Felix Fietkau + * Copyright (C) 2010-2012 Hauke Mehrtens + * + * This program is free software; you can redistribute it and/or modify it + * under the terms of the GNU General Public License as published by the + * Free Software Foundation; either version 2 of the License, or (at your + * option) any later version. + */ + +#include +#include +#include +#include +#include +#include +#include + +#define NVRAM_MAGIC 0x48534C46 /* 'FLSH' */ +#define NVRAM_SPACE 0x10000 +#define NVRAM_MAX_GPIO_ENTRIES 32 +#define NVRAM_MAX_GPIO_VALUE_LEN 30 + +#define FLASH_MIN 0x00020000 /* Minimum flash size */ + +struct nvram_header { + u32 magic; + u32 len; + u32 crc_ver_init; /* 0:7 crc, 8:15 ver, 16:31 sdram_init */ + u32 config_refresh; /* 0:15 sdram_config, 16:31 sdram_refresh */ + u32 config_ncdl; /* ncdl values for memc */ +}; + +static char nvram_buf[NVRAM_SPACE]; +static size_t nvram_len; +static const u32 nvram_sizes[] = {0x8000, 0xF000, 0x10000}; + +static u32 find_nvram_size(void __iomem *end) +{ + struct nvram_header __iomem *header; + int i; + + for (i = 0; i < ARRAY_SIZE(nvram_sizes); i++) { + header = (struct nvram_header *)(end - nvram_sizes[i]); + if (header->magic == NVRAM_MAGIC) + return nvram_sizes[i]; + } + + return 0; +} + +/* Probe for NVRAM header */ +static int nvram_find_and_copy(void __iomem *iobase, u32 lim) +{ + struct nvram_header __iomem *header; + int i; + u32 off; + u32 *src, *dst; + u32 size; + + if (nvram_len) { + pr_warn("nvram already initialized\n"); + return -EEXIST; + } + + /* TODO: when nvram is on nand flash check for bad blocks first. */ + off = FLASH_MIN; + while (off <= lim) { + /* Windowed flash access */ + size = find_nvram_size(iobase + off); + if (size) { + header = (struct nvram_header *)(iobase + off - size); + goto found; + } + off <<= 1; + } + + /* Try embedded NVRAM at 4 KB and 1 KB as last resorts */ + header = (struct nvram_header *)(iobase + 4096); + if (header->magic == NVRAM_MAGIC) { + size = NVRAM_SPACE; + goto found; + } + + header = (struct nvram_header *)(iobase + 1024); + if (header->magic == NVRAM_MAGIC) { + size = NVRAM_SPACE; + goto found; + } + + pr_err("no nvram found\n"); + return -ENXIO; + +found: + src = (u32 *)header; + dst = (u32 *)nvram_buf; + for (i = 0; i < sizeof(struct nvram_header); i += 4) + *dst++ = __raw_readl(src++); + header = (struct nvram_header *)nvram_buf; + nvram_len = header->len; + if (nvram_len > size) { + pr_err("The nvram size according to the header seems to be bigger than the partition on flash\n"); + nvram_len = size; + } + if (nvram_len >= NVRAM_SPACE) { + pr_err("nvram on flash (%i bytes) is bigger than the reserved space in memory, will just copy the first %i bytes\n", + header->len, NVRAM_SPACE - 1); + nvram_len = NVRAM_SPACE - 1; + } + /* proceed reading data after header */ + for (; i < nvram_len; i += 4) + *dst++ = readl(src++); + nvram_buf[NVRAM_SPACE - 1] = '\0'; + + return 0; +} + +/* + * On bcm47xx we need access to the NVRAM very early, so we can't use mtd + * subsystem to access flash. We can't even use platform device / driver to + * store memory offset. + * To handle this we provide following symbol. It's supposed to be called as + * soon as we get info about flash device, before any NVRAM entry is needed. + */ +int bcm47xx_nvram_init_from_mem(u32 base, u32 lim) +{ + void __iomem *iobase; + int err; + + iobase = ioremap_nocache(base, lim); + if (!iobase) + return -ENOMEM; + + err = nvram_find_and_copy(iobase, lim); + + iounmap(iobase); + + return err; +} + +static int nvram_init(void) +{ +#ifdef CONFIG_MTD + struct mtd_info *mtd; + struct nvram_header header; + size_t bytes_read; + int err; + + mtd = get_mtd_device_nm("nvram"); + if (IS_ERR(mtd)) + return -ENODEV; + + err = mtd_read(mtd, 0, sizeof(header), &bytes_read, (uint8_t *)&header); + if (!err && header.magic == NVRAM_MAGIC && + header.len > sizeof(header)) { + nvram_len = header.len; + if (nvram_len >= NVRAM_SPACE) { + pr_err("nvram on flash (%i bytes) is bigger than the reserved space in memory, will just copy the first %i bytes\n", + header.len, NVRAM_SPACE); + nvram_len = NVRAM_SPACE - 1; + } + + err = mtd_read(mtd, 0, nvram_len, &nvram_len, + (u8 *)nvram_buf); + return err; + } +#endif + + return -ENXIO; +} + +int bcm47xx_nvram_getenv(const char *name, char *val, size_t val_len) +{ + char *var, *value, *end, *eq; + int err; + + if (!name) + return -EINVAL; + + if (!nvram_len) { + err = nvram_init(); + if (err) + return err; + } + + /* Look for name=value and return value */ + var = &nvram_buf[sizeof(struct nvram_header)]; + end = nvram_buf + sizeof(nvram_buf); + while (var < end && *var) { + eq = strchr(var, '='); + if (!eq) + break; + value = eq + 1; + if (eq - var == strlen(name) && + strncmp(var, name, eq - var) == 0) + return snprintf(val, val_len, "%s", value); + var = value + strlen(value) + 1; + } + return -ENOENT; +} +EXPORT_SYMBOL(bcm47xx_nvram_getenv); + +int bcm47xx_nvram_gpio_pin(const char *name) +{ + int i, err; + char nvram_var[] = "gpioXX"; + char buf[NVRAM_MAX_GPIO_VALUE_LEN]; + + /* TODO: Optimize it to don't call getenv so many times */ + for (i = 0; i < NVRAM_MAX_GPIO_ENTRIES; i++) { + err = snprintf(nvram_var, sizeof(nvram_var), "gpio%i", i); + if (err <= 0) + continue; + err = bcm47xx_nvram_getenv(nvram_var, buf, sizeof(buf)); + if (err <= 0) + continue; + if (!strcmp(name, buf)) + return i; + } + return -ENOENT; +} +EXPORT_SYMBOL(bcm47xx_nvram_gpio_pin); + +char *bcm47xx_nvram_get_contents(size_t *nvram_size) +{ + int err; + char *nvram; + + if (!nvram_len) { + err = nvram_init(); + if (err) + return NULL; + } + + *nvram_size = nvram_len - sizeof(struct nvram_header); + nvram = vmalloc(*nvram_size); + if (!nvram) + return NULL; + memcpy(nvram, &nvram_buf[sizeof(struct nvram_header)], *nvram_size); + + return nvram; +} +EXPORT_SYMBOL(bcm47xx_nvram_get_contents); + +MODULE_LICENSE("GPLv2"); diff --git a/target/linux/bcm53xx/files-4.1/include/linux/bcm47xx_nvram.h b/target/linux/bcm53xx/files-4.1/include/linux/bcm47xx_nvram.h new file mode 100644 index 0000000000..2793652fbf --- /dev/null +++ b/target/linux/bcm53xx/files-4.1/include/linux/bcm47xx_nvram.h @@ -0,0 +1,49 @@ +/* + * This program is free software; you can redistribute it and/or modify it + * under the terms of the GNU General Public License as published by the + * Free Software Foundation; either version 2 of the License, or (at your + * option) any later version. + */ + +#ifndef __BCM47XX_NVRAM_H +#define __BCM47XX_NVRAM_H + +#include +#include +#include + +#ifdef CONFIG_BCM47XX_NVRAM +int bcm47xx_nvram_init_from_mem(u32 base, u32 lim); +int bcm47xx_nvram_getenv(const char *name, char *val, size_t val_len); +int bcm47xx_nvram_gpio_pin(const char *name); +char *bcm47xx_nvram_get_contents(size_t *val_len); +static inline void bcm47xx_nvram_release_contents(char *nvram) +{ + vfree(nvram); +}; +#else +static inline int bcm47xx_nvram_init_from_mem(u32 base, u32 lim) +{ + return -ENOTSUPP; +}; +static inline int bcm47xx_nvram_getenv(const char *name, char *val, + size_t val_len) +{ + return -ENOTSUPP; +}; +static inline int bcm47xx_nvram_gpio_pin(const char *name) +{ + return -ENOTSUPP; +}; + +static inline char *bcm47xx_nvram_get_contents(size_t *val_len) +{ + return NULL; +}; + +static inline void bcm47xx_nvram_release_contents(char *nvram) +{ +}; +#endif + +#endif /* __BCM47XX_NVRAM_H */ diff --git a/target/linux/bcm53xx/files/drivers/firmware/broadcom/Kconfig b/target/linux/bcm53xx/files/drivers/firmware/broadcom/Kconfig deleted file mode 100644 index 6bed119930..0000000000 --- a/target/linux/bcm53xx/files/drivers/firmware/broadcom/Kconfig +++ /dev/null @@ -1,11 +0,0 @@ -config BCM47XX_NVRAM - bool "Broadcom NVRAM driver" - depends on BCM47XX || ARCH_BCM_5301X - help - Broadcom home routers contain flash partition called "nvram" with all - important hardware configuration as well as some minor user setup. - NVRAM partition contains a text-like data representing name=value - pairs. - This driver provides an easy way to get value of requested parameter. - It simply reads content of NVRAM and parses it. It doesn't control any - hardware part itself. diff --git a/target/linux/bcm53xx/files/drivers/firmware/broadcom/Makefile b/target/linux/bcm53xx/files/drivers/firmware/broadcom/Makefile deleted file mode 100644 index d0e683583c..0000000000 --- a/target/linux/bcm53xx/files/drivers/firmware/broadcom/Makefile +++ /dev/null @@ -1 +0,0 @@ -obj-$(CONFIG_BCM47XX_NVRAM) += bcm47xx_nvram.o diff --git a/target/linux/bcm53xx/files/drivers/firmware/broadcom/bcm47xx_nvram.c b/target/linux/bcm53xx/files/drivers/firmware/broadcom/bcm47xx_nvram.c deleted file mode 100644 index 87add3fdce..0000000000 --- a/target/linux/bcm53xx/files/drivers/firmware/broadcom/bcm47xx_nvram.c +++ /dev/null @@ -1,248 +0,0 @@ -/* - * BCM947xx nvram variable access - * - * Copyright (C) 2005 Broadcom Corporation - * Copyright (C) 2006 Felix Fietkau - * Copyright (C) 2010-2012 Hauke Mehrtens - * - * This program is free software; you can redistribute it and/or modify it - * under the terms of the GNU General Public License as published by the - * Free Software Foundation; either version 2 of the License, or (at your - * option) any later version. - */ - -#include -#include -#include -#include -#include -#include -#include - -#define NVRAM_MAGIC 0x48534C46 /* 'FLSH' */ -#define NVRAM_SPACE 0x10000 -#define NVRAM_MAX_GPIO_ENTRIES 32 -#define NVRAM_MAX_GPIO_VALUE_LEN 30 - -#define FLASH_MIN 0x00020000 /* Minimum flash size */ - -struct nvram_header { - u32 magic; - u32 len; - u32 crc_ver_init; /* 0:7 crc, 8:15 ver, 16:31 sdram_init */ - u32 config_refresh; /* 0:15 sdram_config, 16:31 sdram_refresh */ - u32 config_ncdl; /* ncdl values for memc */ -}; - -static char nvram_buf[NVRAM_SPACE]; -static size_t nvram_len; -static const u32 nvram_sizes[] = {0x8000, 0xF000, 0x10000}; - -static u32 find_nvram_size(void __iomem *end) -{ - struct nvram_header __iomem *header; - int i; - - for (i = 0; i < ARRAY_SIZE(nvram_sizes); i++) { - header = (struct nvram_header *)(end - nvram_sizes[i]); - if (header->magic == NVRAM_MAGIC) - return nvram_sizes[i]; - } - - return 0; -} - -/* Probe for NVRAM header */ -static int nvram_find_and_copy(void __iomem *iobase, u32 lim) -{ - struct nvram_header __iomem *header; - int i; - u32 off; - u32 *src, *dst; - u32 size; - - if (nvram_len) { - pr_warn("nvram already initialized\n"); - return -EEXIST; - } - - /* TODO: when nvram is on nand flash check for bad blocks first. */ - off = FLASH_MIN; - while (off <= lim) { - /* Windowed flash access */ - size = find_nvram_size(iobase + off); - if (size) { - header = (struct nvram_header *)(iobase + off - size); - goto found; - } - off <<= 1; - } - - /* Try embedded NVRAM at 4 KB and 1 KB as last resorts */ - header = (struct nvram_header *)(iobase + 4096); - if (header->magic == NVRAM_MAGIC) { - size = NVRAM_SPACE; - goto found; - } - - header = (struct nvram_header *)(iobase + 1024); - if (header->magic == NVRAM_MAGIC) { - size = NVRAM_SPACE; - goto found; - } - - pr_err("no nvram found\n"); - return -ENXIO; - -found: - src = (u32 *)header; - dst = (u32 *)nvram_buf; - for (i = 0; i < sizeof(struct nvram_header); i += 4) - *dst++ = __raw_readl(src++); - header = (struct nvram_header *)nvram_buf; - nvram_len = header->len; - if (nvram_len > size) { - pr_err("The nvram size according to the header seems to be bigger than the partition on flash\n"); - nvram_len = size; - } - if (nvram_len >= NVRAM_SPACE) { - pr_err("nvram on flash (%i bytes) is bigger than the reserved space in memory, will just copy the first %i bytes\n", - header->len, NVRAM_SPACE - 1); - nvram_len = NVRAM_SPACE - 1; - } - /* proceed reading data after header */ - for (; i < nvram_len; i += 4) - *dst++ = readl(src++); - nvram_buf[NVRAM_SPACE - 1] = '\0'; - - return 0; -} - -/* - * On bcm47xx we need access to the NVRAM very early, so we can't use mtd - * subsystem to access flash. We can't even use platform device / driver to - * store memory offset. - * To handle this we provide following symbol. It's supposed to be called as - * soon as we get info about flash device, before any NVRAM entry is needed. - */ -int bcm47xx_nvram_init_from_mem(u32 base, u32 lim) -{ - void __iomem *iobase; - int err; - - iobase = ioremap_nocache(base, lim); - if (!iobase) - return -ENOMEM; - - err = nvram_find_and_copy(iobase, lim); - - iounmap(iobase); - - return err; -} - -static int nvram_init(void) -{ -#ifdef CONFIG_MTD - struct mtd_info *mtd; - struct nvram_header header; - size_t bytes_read; - int err; - - mtd = get_mtd_device_nm("nvram"); - if (IS_ERR(mtd)) - return -ENODEV; - - err = mtd_read(mtd, 0, sizeof(header), &bytes_read, (uint8_t *)&header); - if (!err && header.magic == NVRAM_MAGIC && - header.len > sizeof(header)) { - nvram_len = header.len; - if (nvram_len >= NVRAM_SPACE) { - pr_err("nvram on flash (%i bytes) is bigger than the reserved space in memory, will just copy the first %i bytes\n", - header.len, NVRAM_SPACE); - nvram_len = NVRAM_SPACE - 1; - } - - err = mtd_read(mtd, 0, nvram_len, &nvram_len, - (u8 *)nvram_buf); - return err; - } -#endif - - return -ENXIO; -} - -int bcm47xx_nvram_getenv(const char *name, char *val, size_t val_len) -{ - char *var, *value, *end, *eq; - int err; - - if (!name) - return -EINVAL; - - if (!nvram_len) { - err = nvram_init(); - if (err) - return err; - } - - /* Look for name=value and return value */ - var = &nvram_buf[sizeof(struct nvram_header)]; - end = nvram_buf + sizeof(nvram_buf); - while (var < end && *var) { - eq = strchr(var, '='); - if (!eq) - break; - value = eq + 1; - if (eq - var == strlen(name) && - strncmp(var, name, eq - var) == 0) - return snprintf(val, val_len, "%s", value); - var = value + strlen(value) + 1; - } - return -ENOENT; -} -EXPORT_SYMBOL(bcm47xx_nvram_getenv); - -int bcm47xx_nvram_gpio_pin(const char *name) -{ - int i, err; - char nvram_var[] = "gpioXX"; - char buf[NVRAM_MAX_GPIO_VALUE_LEN]; - - /* TODO: Optimize it to don't call getenv so many times */ - for (i = 0; i < NVRAM_MAX_GPIO_ENTRIES; i++) { - err = snprintf(nvram_var, sizeof(nvram_var), "gpio%i", i); - if (err <= 0) - continue; - err = bcm47xx_nvram_getenv(nvram_var, buf, sizeof(buf)); - if (err <= 0) - continue; - if (!strcmp(name, buf)) - return i; - } - return -ENOENT; -} -EXPORT_SYMBOL(bcm47xx_nvram_gpio_pin); - -char *bcm47xx_nvram_get_contents(size_t *nvram_size) -{ - int err; - char *nvram; - - if (!nvram_len) { - err = nvram_init(); - if (err) - return NULL; - } - - *nvram_size = nvram_len - sizeof(struct nvram_header); - nvram = vmalloc(*nvram_size); - if (!nvram) - return NULL; - memcpy(nvram, &nvram_buf[sizeof(struct nvram_header)], *nvram_size); - - return nvram; -} -EXPORT_SYMBOL(bcm47xx_nvram_get_contents); - -MODULE_LICENSE("GPLv2"); diff --git a/target/linux/bcm53xx/files/include/linux/bcm47xx_nvram.h b/target/linux/bcm53xx/files/include/linux/bcm47xx_nvram.h deleted file mode 100644 index 2793652fbf..0000000000 --- a/target/linux/bcm53xx/files/include/linux/bcm47xx_nvram.h +++ /dev/null @@ -1,49 +0,0 @@ -/* - * This program is free software; you can redistribute it and/or modify it - * under the terms of the GNU General Public License as published by the - * Free Software Foundation; either version 2 of the License, or (at your - * option) any later version. - */ - -#ifndef __BCM47XX_NVRAM_H -#define __BCM47XX_NVRAM_H - -#include -#include -#include - -#ifdef CONFIG_BCM47XX_NVRAM -int bcm47xx_nvram_init_from_mem(u32 base, u32 lim); -int bcm47xx_nvram_getenv(const char *name, char *val, size_t val_len); -int bcm47xx_nvram_gpio_pin(const char *name); -char *bcm47xx_nvram_get_contents(size_t *val_len); -static inline void bcm47xx_nvram_release_contents(char *nvram) -{ - vfree(nvram); -}; -#else -static inline int bcm47xx_nvram_init_from_mem(u32 base, u32 lim) -{ - return -ENOTSUPP; -}; -static inline int bcm47xx_nvram_getenv(const char *name, char *val, - size_t val_len) -{ - return -ENOTSUPP; -}; -static inline int bcm47xx_nvram_gpio_pin(const char *name) -{ - return -ENOTSUPP; -}; - -static inline char *bcm47xx_nvram_get_contents(size_t *val_len) -{ - return NULL; -}; - -static inline void bcm47xx_nvram_release_contents(char *nvram) -{ -}; -#endif - -#endif /* __BCM47XX_NVRAM_H */ diff --git a/target/linux/bcm53xx/patches-4.3/067-ARM-BCM5301X-add-NAND-flash-chip-description-for-Asu.patch b/target/linux/bcm53xx/patches-4.3/067-ARM-BCM5301X-add-NAND-flash-chip-description-for-Asu.patch new file mode 100644 index 0000000000..ccb8e2769f --- /dev/null +++ b/target/linux/bcm53xx/patches-4.3/067-ARM-BCM5301X-add-NAND-flash-chip-description-for-Asu.patch @@ -0,0 +1,32 @@ +From af8fe7176ec13de08b1bfb7ea2ae9cc147b2429a Mon Sep 17 00:00:00 2001 +From: Hauke Mehrtens +Date: Sat, 12 Sep 2015 12:56:37 +0200 +Subject: [PATCH] ARM: BCM5301X: add NAND flash chip description for Asus + RT-AC87U + +The NAND flash chip description were not imported for the Asus RT-AC87U +dts file when this was done for all the other dts files, because these +patches were send in parallel. + +This adds a missing NAND flash chip description to this patch: +commit 9faa5960eef3204cae6637b530f5e23e53b5a9ef +Author: Hauke Mehrtens +Date: Fri May 29 23:39:47 2015 +0200 + +ARM: BCM5301X: add NAND flash chip description + +Signed-off-by: Hauke Mehrtens +--- + arch/arm/boot/dts/bcm4709-asus-rt-ac87u.dts | 1 + + 1 file changed, 1 insertion(+) + +--- a/arch/arm/boot/dts/bcm4709-asus-rt-ac87u.dts ++++ b/arch/arm/boot/dts/bcm4709-asus-rt-ac87u.dts +@@ -10,6 +10,7 @@ + /dts-v1/; + + #include "bcm4708.dtsi" ++#include "bcm5301x-nand-cs0-bch8.dtsi" + + / { + compatible = "asus,rt-ac87u", "brcm,bcm4709", "brcm,bcm4708"; diff --git a/target/linux/bcm53xx/patches-4.3/082-ARM-BCM5301X-Add-DT-for-Netgear-R7000.patch b/target/linux/bcm53xx/patches-4.3/082-ARM-BCM5301X-Add-DT-for-Netgear-R7000.patch new file mode 100644 index 0000000000..044fb80607 --- /dev/null +++ b/target/linux/bcm53xx/patches-4.3/082-ARM-BCM5301X-Add-DT-for-Netgear-R7000.patch @@ -0,0 +1,128 @@ +From: =?UTF-8?q?Rafa=C5=82=20Mi=C5=82ecki?= +Date: Wed, 26 Aug 2015 16:11:38 +0200 +Subject: [PATCH] ARM: BCM5301X: Add DT for Netgear R7000 +MIME-Version: 1.0 +Content-Type: text/plain; charset=UTF-8 +Content-Transfer-Encoding: 8bit + +Signed-off-by: Rafał Miłecki +--- +--- a/arch/arm/boot/dts/Makefile ++++ b/arch/arm/boot/dts/Makefile +@@ -72,6 +72,7 @@ dtb-$(CONFIG_ARCH_BCM_5301X) += \ + bcm47081-buffalo-wzr-900dhp.dtb \ + bcm4709-asus-rt-ac87u.dtb \ + bcm4709-buffalo-wxr-1900dhp.dtb \ ++ bcm4709-netgear-r7000.dtb \ + bcm4709-netgear-r8000.dtb + dtb-$(CONFIG_ARCH_BCM_63XX) += \ + bcm963138dvt.dtb +--- /dev/null ++++ b/arch/arm/boot/dts/bcm4709-netgear-r7000.dts +@@ -0,0 +1,106 @@ ++/* ++ * Broadcom BCM470X / BCM5301X ARM platform code. ++ * DTS for Netgear R7000 ++ * ++ * Copyright (C) 2015 Rafał Miłecki ++ * ++ * Licensed under the GNU/GPL. See COPYING for details. ++ */ ++ ++/dts-v1/; ++ ++#include "bcm4708.dtsi" ++#include "bcm5301x-nand-cs0-bch8.dtsi" ++ ++/ { ++ compatible = "netgear,r7000", "brcm,bcm4709", "brcm,bcm4708"; ++ model = "Netgear R7000"; ++ ++ chosen { ++ bootargs = "console=ttyS0,115200"; ++ }; ++ ++ memory { ++ reg = <0x00000000 0x08000000>; ++ }; ++ ++ leds { ++ compatible = "gpio-leds"; ++ ++ power-white { ++ label = "bcm53xx:white:power"; ++ gpios = <&chipcommon 2 GPIO_ACTIVE_LOW>; ++ linux,default-trigger = "default-on"; ++ }; ++ ++ power-amber { ++ label = "bcm53xx:amber:power"; ++ gpios = <&chipcommon 3 GPIO_ACTIVE_LOW>; ++ linux,default-trigger = "default-off"; ++ }; ++ ++ 5ghz { ++ label = "bcm53xx:white:5ghz"; ++ gpios = <&chipcommon 12 GPIO_ACTIVE_LOW>; ++ linux,default-trigger = "default-off"; ++ }; ++ ++ 2ghz { ++ label = "bcm53xx:white:2ghz"; ++ gpios = <&chipcommon 13 GPIO_ACTIVE_LOW>; ++ linux,default-trigger = "default-off"; ++ }; ++ ++ wps { ++ label = "bcm53xx:white:wps"; ++ gpios = <&chipcommon 14 GPIO_ACTIVE_HIGH>; ++ linux,default-trigger = "default-off"; ++ }; ++ ++ wireless { ++ label = "bcm53xx:white:wireless"; ++ gpios = <&chipcommon 15 GPIO_ACTIVE_HIGH>; ++ linux,default-trigger = "default-off"; ++ }; ++ ++ usb3 { ++ label = "bcm53xx:white:usb3"; ++ gpios = <&chipcommon 17 GPIO_ACTIVE_LOW>; ++ linux,default-trigger = "default-off"; ++ }; ++ ++ usb2 { ++ label = "bcm53xx:white:usb2"; ++ gpios = <&chipcommon 18 GPIO_ACTIVE_LOW>; ++ linux,default-trigger = "default-off"; ++ }; ++ }; ++ ++ gpio-keys { ++ compatible = "gpio-keys"; ++ #address-cells = <1>; ++ #size-cells = <0>; ++ ++ wps { ++ label = "WPS"; ++ linux,code = ; ++ gpios = <&chipcommon 4 GPIO_ACTIVE_LOW>; ++ }; ++ ++ rfkill { ++ label = "WiFi"; ++ linux,code = ; ++ gpios = <&chipcommon 5 GPIO_ACTIVE_LOW>; ++ }; ++ ++ restart { ++ label = "Reset"; ++ linux,code = ; ++ gpios = <&chipcommon 6 GPIO_ACTIVE_LOW>; ++ }; ++ }; ++}; ++ ++&uart0 { ++ status = "okay"; ++}; diff --git a/target/linux/bcm53xx/patches-4.3/083-ARM-dts-bcm5301x-Add-BCM-SVK-DT-files.patch b/target/linux/bcm53xx/patches-4.3/083-ARM-dts-bcm5301x-Add-BCM-SVK-DT-files.patch new file mode 100644 index 0000000000..0dae7c9144 --- /dev/null +++ b/target/linux/bcm53xx/patches-4.3/083-ARM-dts-bcm5301x-Add-BCM-SVK-DT-files.patch @@ -0,0 +1,218 @@ +From a0aef7fbab0d8b5a0d445c74990e5233beda246e Mon Sep 17 00:00:00 2001 +From: Jon Mason +Date: Wed, 21 Oct 2015 18:46:04 -0400 +Subject: [PATCH] ARM: dts: bcm5301x: Add BCM SVK DT files + +Add device tree files for Broadcom Northstar based SVKs. Since the +bcm5301x.dtsi already exists, all that is necessary is the dts files to +enable the UARTs. With these files, the SVKs are able to boot to shell. + +Signed-off-by: Jon Mason +--- + arch/arm/boot/dts/Makefile | 5 +++- + arch/arm/boot/dts/bcm94708.dts | 56 +++++++++++++++++++++++++++++++++++ + arch/arm/boot/dts/bcm94709.dts | 56 +++++++++++++++++++++++++++++++++++ + arch/arm/boot/dts/bcm953012k.dts | 63 ++++++++++++++++++++++++++++++++++++++++ + 4 files changed, 179 insertions(+), 1 deletion(-) + create mode 100644 arch/arm/boot/dts/bcm94708.dts + create mode 100644 arch/arm/boot/dts/bcm94709.dts + create mode 100644 arch/arm/boot/dts/bcm953012k.dts + +--- a/arch/arm/boot/dts/Makefile ++++ b/arch/arm/boot/dts/Makefile +@@ -73,7 +73,10 @@ dtb-$(CONFIG_ARCH_BCM_5301X) += \ + bcm4709-asus-rt-ac87u.dtb \ + bcm4709-buffalo-wxr-1900dhp.dtb \ + bcm4709-netgear-r7000.dtb \ +- bcm4709-netgear-r8000.dtb ++ bcm4709-netgear-r8000.dtb \ ++ bcm94708.dtb \ ++ bcm94709.dtb \ ++ bcm953012k.dtb + dtb-$(CONFIG_ARCH_BCM_63XX) += \ + bcm963138dvt.dtb + dtb-$(CONFIG_ARCH_BCM_CYGNUS) += \ +--- /dev/null ++++ b/arch/arm/boot/dts/bcm94708.dts +@@ -0,0 +1,56 @@ ++/* ++ * BSD LICENSE ++ * ++ * Copyright(c) 2015 Broadcom Corporation. All rights reserved. ++ * ++ * Redistribution and use in source and binary forms, with or without ++ * modification, are permitted provided that the following conditions ++ * are met: ++ * ++ * * Redistributions of source code must retain the above copyright ++ * notice, this list of conditions and the following disclaimer. ++ * * Redistributions in binary form must reproduce the above copyright ++ * notice, this list of conditions and the following disclaimer in ++ * the documentation and/or other materials provided with the ++ * distribution. ++ * * Neither the name of Broadcom Corporation nor the names of its ++ * contributors may be used to endorse or promote products derived ++ * from this software without specific prior written permission. ++ * ++ * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS ++ * "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT ++ * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR ++ * A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT ++ * OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, ++ * SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT ++ * LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, ++ * DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY ++ * THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT ++ * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE ++ * OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. ++ */ ++ ++/dts-v1/; ++ ++#include "bcm4708.dtsi" ++ ++/ { ++ model = "NorthStar SVK (BCM94708)"; ++ compatible = "brcm,bcm94708", "brcm,bcm4708"; ++ ++ aliases { ++ serial0 = &uart0; ++ }; ++ ++ chosen { ++ stdout-path = "serial0:115200n8"; ++ }; ++ ++ memory { ++ reg = <0x00000000 0x08000000>; ++ }; ++}; ++ ++&uart0 { ++ status = "okay"; ++}; +--- /dev/null ++++ b/arch/arm/boot/dts/bcm94709.dts +@@ -0,0 +1,56 @@ ++/* ++ * BSD LICENSE ++ * ++ * Copyright(c) 2015 Broadcom Corporation. All rights reserved. ++ * ++ * Redistribution and use in source and binary forms, with or without ++ * modification, are permitted provided that the following conditions ++ * are met: ++ * ++ * * Redistributions of source code must retain the above copyright ++ * notice, this list of conditions and the following disclaimer. ++ * * Redistributions in binary form must reproduce the above copyright ++ * notice, this list of conditions and the following disclaimer in ++ * the documentation and/or other materials provided with the ++ * distribution. ++ * * Neither the name of Broadcom Corporation nor the names of its ++ * contributors may be used to endorse or promote products derived ++ * from this software without specific prior written permission. ++ * ++ * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS ++ * "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT ++ * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR ++ * A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT ++ * OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, ++ * SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT ++ * LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, ++ * DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY ++ * THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT ++ * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE ++ * OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. ++ */ ++ ++/dts-v1/; ++ ++#include "bcm4708.dtsi" ++ ++/ { ++ model = "NorthStar SVK (BCM94709)"; ++ compatible = "brcm,bcm94709", "brcm,bcm4709", "brcm,bcm4708"; ++ ++ aliases { ++ serial0 = &uart0; ++ }; ++ ++ chosen { ++ stdout-path = "serial0:115200n8"; ++ }; ++ ++ memory { ++ reg = <0x00000000 0x08000000>; ++ }; ++}; ++ ++&uart0 { ++ status = "okay"; ++}; +--- /dev/null ++++ b/arch/arm/boot/dts/bcm953012k.dts +@@ -0,0 +1,63 @@ ++/* ++ * BSD LICENSE ++ * ++ * Copyright(c) 2015 Broadcom Corporation. All rights reserved. ++ * ++ * Redistribution and use in source and binary forms, with or without ++ * modification, are permitted provided that the following conditions ++ * are met: ++ * ++ * * Redistributions of source code must retain the above copyright ++ * notice, this list of conditions and the following disclaimer. ++ * * Redistributions in binary form must reproduce the above copyright ++ * notice, this list of conditions and the following disclaimer in ++ * the documentation and/or other materials provided with the ++ * distribution. ++ * * Neither the name of Broadcom Corporation nor the names of its ++ * contributors may be used to endorse or promote products derived ++ * from this software without specific prior written permission. ++ * ++ * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS ++ * "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT ++ * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR ++ * A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT ++ * OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, ++ * SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT ++ * LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, ++ * DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY ++ * THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT ++ * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE ++ * OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. ++ */ ++ ++/dts-v1/; ++ ++#include "bcm4708.dtsi" ++ ++/ { ++ model = "NorthStar SVK (BCM953012K)"; ++ compatible = "brcm,bcm953012k", "brcm,brcm53012", "brcm,bcm4708"; ++ ++ aliases { ++ serial0 = &uart0; ++ serial1 = &uart1; ++ }; ++ ++ chosen { ++ stdout-path = "serial0:115200n8"; ++ }; ++ ++ memory { ++ reg = <0x00000000 0x10000000>; ++ }; ++}; ++ ++&uart0 { ++ clock-frequency = <62499840>; ++ status = "okay"; ++}; ++ ++&uart1 { ++ clock-frequency = <62499840>; ++ status = "okay"; ++}; diff --git a/target/linux/bcm53xx/patches-4.3/101-use-part-parser.patch b/target/linux/bcm53xx/patches-4.3/101-use-part-parser.patch new file mode 100644 index 0000000000..8d48673c6d --- /dev/null +++ b/target/linux/bcm53xx/patches-4.3/101-use-part-parser.patch @@ -0,0 +1,11 @@ +--- a/arch/arm/boot/dts/bcm5301x-nand-cs0-bch8.dtsi ++++ b/arch/arm/boot/dts/bcm5301x-nand-cs0-bch8.dtsi +@@ -19,6 +19,8 @@ + + nand-ecc-strength = <8>; + nand-ecc-step-size = <512>; ++ ++ linux,part-probe = "ofpart", "bcm47xxpart"; + }; + }; + }; diff --git a/target/linux/bcm53xx/patches-4.3/112-bcm53xx-sprom-add-sprom-driver.patch b/target/linux/bcm53xx/patches-4.3/112-bcm53xx-sprom-add-sprom-driver.patch new file mode 100644 index 0000000000..70ab03995c --- /dev/null +++ b/target/linux/bcm53xx/patches-4.3/112-bcm53xx-sprom-add-sprom-driver.patch @@ -0,0 +1,69 @@ +From 4e0ab3269a6d260a41a3673157753147f5f71341 Mon Sep 17 00:00:00 2001 +From: Hauke Mehrtens +Date: Sun, 4 May 2014 13:19:20 +0200 +Subject: [PATCH 03/17] bcm47xx-sprom: add Broadcom sprom parser driver + +This driver needs an nvram driver and fetches the sprom values from the +nvram and provides it to any other driver. The calibration data for the +wifi chip the mac address and some more board description data is +stores in the sprom. + +This is based on a copy of arch/mips/bcm47xx/sprom.c and my plan is to +make the bcm47xx MIPS SoCs also use this driver some time later. + +Signed-off-by: Hauke Mehrtens +--- + .../devicetree/bindings/misc/bcm47xx-sprom.txt | 16 + + drivers/misc/Kconfig | 11 + + drivers/misc/Makefile | 1 + + drivers/misc/bcm47xx-sprom.c | 690 +++++++++++++++++++++ + 4 files changed, 718 insertions(+) + create mode 100644 Documentation/devicetree/bindings/misc/bcm47xx-sprom.txt + create mode 100644 drivers/misc/bcm47xx-sprom.c + +--- /dev/null ++++ b/Documentation/devicetree/bindings/misc/bcm47xx-sprom.txt +@@ -0,0 +1,16 @@ ++Broadcom bcm47xx/bcm53xx sprom converter ++ ++This driver provbides an sprom based on a given nvram. ++ ++Required properties: ++ ++- compatible : brcm,bcm47xx-sprom ++ ++- nvram : reference to a nvram driver, e.g. bcm47xx-nvram ++ ++Example: ++ ++sprom0: sprom@0 { ++ compatible = "brcm,bcm47xx-sprom"; ++ nvram = <&nvram0>; ++}; +--- a/drivers/misc/Kconfig ++++ b/drivers/misc/Kconfig +@@ -525,6 +525,17 @@ config VEXPRESS_SYSCFG + bus. System Configuration interface is one of the possible means + of generating transactions on this bus. + ++config BCM47XX_SPROM ++ tristate "BCM47XX sprom driver" ++ help ++ This driver parses the sprom from a given nvram which is found on ++ Broadcom bcm47xx and bcm53xx SoCs. ++ ++ The sprom contains board configuration data like the ++ calibration data fro the wifi chips, the mac addresses used ++ by the board and many other board configuration data. This ++ driver will provide the sprom to bcma. ++ + source "drivers/misc/c2port/Kconfig" + source "drivers/misc/eeprom/Kconfig" + source "drivers/misc/cb710/Kconfig" +--- a/drivers/misc/Makefile ++++ b/drivers/misc/Makefile +@@ -56,3 +56,4 @@ obj-$(CONFIG_GENWQE) += genwqe/ + obj-$(CONFIG_ECHO) += echo/ + obj-$(CONFIG_VEXPRESS_SYSCFG) += vexpress-syscfg.o + obj-$(CONFIG_CXL_BASE) += cxl/ ++obj-$(CONFIG_BCM47XX_SPROM) += bcm47xx-sprom.o diff --git a/target/linux/bcm53xx/patches-4.3/130-ARM-BCM-Add-SMP-support-for-Broadcom-NSP.patch b/target/linux/bcm53xx/patches-4.3/130-ARM-BCM-Add-SMP-support-for-Broadcom-NSP.patch new file mode 100644 index 0000000000..5e3bd7793d --- /dev/null +++ b/target/linux/bcm53xx/patches-4.3/130-ARM-BCM-Add-SMP-support-for-Broadcom-NSP.patch @@ -0,0 +1,635 @@ +From a0ad1511d5805b95ac4c454d7904c670a1696055 Mon Sep 17 00:00:00 2001 +From: Kapil Hali +Date: Wed, 14 Oct 2015 13:47:00 -0400 +Subject: [PATCH] ARM: BCM: Add SMP support for Broadcom NSP + +Add SMP support for Broadcom's Northstar Plus SoC, +cpu enable method and pen_release procedures. This +changes also consolidates iProc family's - BCM NSP +and BCM Kona, SMP handling in a common file. + +Northstar Plus SoC is based on ARM Cortex-A9 +revision r3p0 which requires configuration for ARM +Errata 764369 for SMP. This change adds the needed +configuration option. + +Signed-off-by: Kapil Hali +--- + arch/arm/mach-bcm/Makefile | 2 +- + arch/arm/mach-bcm/bcm_nsp.h | 19 +++ + arch/arm/mach-bcm/headsmp.S | 37 +++++ + arch/arm/mach-bcm/kona_smp.c | 202 --------------------------- + arch/arm/mach-bcm/platsmp.c | 326 +++++++++++++++++++++++++++++++++++++++++++ + 5 files changed, 383 insertions(+), 203 deletions(-) + create mode 100644 arch/arm/mach-bcm/bcm_nsp.h + create mode 100644 arch/arm/mach-bcm/headsmp.S + delete mode 100644 arch/arm/mach-bcm/kona_smp.c + create mode 100644 arch/arm/mach-bcm/platsmp.c + +--- a/arch/arm/mach-bcm/Makefile ++++ b/arch/arm/mach-bcm/Makefile +@@ -20,7 +20,7 @@ obj-$(CONFIG_ARCH_BCM_281XX) += board_bc + obj-$(CONFIG_ARCH_BCM_21664) += board_bcm21664.o + + # BCM281XX and BCM21664 SMP support +-obj-$(CONFIG_ARCH_BCM_MOBILE_SMP) += kona_smp.o ++obj-$(CONFIG_ARCH_BCM_MOBILE_SMP) += platsmp.o + + # BCM281XX and BCM21664 L2 cache control + obj-$(CONFIG_ARCH_BCM_MOBILE_L2_CACHE) += kona_l2_cache.o +--- /dev/null ++++ b/arch/arm/mach-bcm/bcm_nsp.h +@@ -0,0 +1,19 @@ ++/* ++ * Copyright (C) 2015 Broadcom Corporation ++ * ++ * This program is free software; you can redistribute it and/or ++ * modify it under the terms of the GNU General Public License as ++ * published by the Free Software Foundation version 2. ++ * ++ * This program is distributed "as is" WITHOUT ANY WARRANTY of any ++ * kind, whether express or implied; without even the implied warranty ++ * of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the ++ * GNU General Public License for more details. ++ */ ++ ++#ifndef __BCM_NSP_H ++#define __BCM_NSP_H ++ ++extern void nsp_secondary_startup(void); ++ ++#endif /* __BCM_NSP_H */ +--- /dev/null ++++ b/arch/arm/mach-bcm/headsmp.S +@@ -0,0 +1,37 @@ ++/* ++ * Copyright (C) 2015 Broadcom Corporation ++ * ++ * This program is free software; you can redistribute it and/or ++ * modify it under the terms of the GNU General Public License as ++ * published by the Free Software Foundation version 2. ++ * ++ * This program is distributed "as is" WITHOUT ANY WARRANTY of any ++ * kind, whether express or implied; without even the implied warranty ++ * of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the ++ * GNU General Public License for more details. ++ */ ++ ++#include ++ ++/* ++ * iProc specific entry point for secondary CPUs. This provides ++ * a "holding pen" into which all secondary cores are held until ++ * we are ready for them to initialise. ++ */ ++ENTRY(nsp_secondary_startup) ++ mrc p15, 0, r0, c0, c0, 5 ++ and r0, r0, #15 ++ adr r4, 1f ++ ldmia r4, {r5, r6} ++ sub r4, r4, r5 ++ add r6, r6, r4 ++pen: ldr r7, [r6] ++ cmp r7, r0 ++ bne pen ++ ++ b secondary_startup ++ ++1: .long . ++ .long pen_release ++ ++ENDPROC(nsp_secondary_startup) +--- a/arch/arm/mach-bcm/kona_smp.c ++++ /dev/null +@@ -1,202 +0,0 @@ +-/* +- * Copyright (C) 2014 Broadcom Corporation +- * Copyright 2014 Linaro Limited +- * +- * This program is free software; you can redistribute it and/or +- * modify it under the terms of the GNU General Public License as +- * published by the Free Software Foundation version 2. +- * +- * This program is distributed "as is" WITHOUT ANY WARRANTY of any +- * kind, whether express or implied; without even the implied warranty +- * of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the +- * GNU General Public License for more details. +- */ +- +-#include +-#include +-#include +-#include +-#include +- +-#include +-#include +-#include +- +-/* Size of mapped Cortex A9 SCU address space */ +-#define CORTEX_A9_SCU_SIZE 0x58 +- +-#define SECONDARY_TIMEOUT_NS NSEC_PER_MSEC /* 1 msec (in nanoseconds) */ +-#define BOOT_ADDR_CPUID_MASK 0x3 +- +-/* Name of device node property defining secondary boot register location */ +-#define OF_SECONDARY_BOOT "secondary-boot-reg" +- +-/* I/O address of register used to coordinate secondary core startup */ +-static u32 secondary_boot; +- +-/* +- * Enable the Cortex A9 Snoop Control Unit +- * +- * By the time this is called we already know there are multiple +- * cores present. We assume we're running on a Cortex A9 processor, +- * so any trouble getting the base address register or getting the +- * SCU base is a problem. +- * +- * Return 0 if successful or an error code otherwise. +- */ +-static int __init scu_a9_enable(void) +-{ +- unsigned long config_base; +- void __iomem *scu_base; +- +- if (!scu_a9_has_base()) { +- pr_err("no configuration base address register!\n"); +- return -ENXIO; +- } +- +- /* Config base address register value is zero for uniprocessor */ +- config_base = scu_a9_get_base(); +- if (!config_base) { +- pr_err("hardware reports only one core\n"); +- return -ENOENT; +- } +- +- scu_base = ioremap((phys_addr_t)config_base, CORTEX_A9_SCU_SIZE); +- if (!scu_base) { +- pr_err("failed to remap config base (%lu/%u) for SCU\n", +- config_base, CORTEX_A9_SCU_SIZE); +- return -ENOMEM; +- } +- +- scu_enable(scu_base); +- +- iounmap(scu_base); /* That's the last we'll need of this */ +- +- return 0; +-} +- +-static void __init bcm_smp_prepare_cpus(unsigned int max_cpus) +-{ +- static cpumask_t only_cpu_0 = { CPU_BITS_CPU0 }; +- struct device_node *node; +- int ret; +- +- BUG_ON(secondary_boot); /* We're called only once */ +- +- /* +- * This function is only called via smp_ops->smp_prepare_cpu(). +- * That only happens if a "/cpus" device tree node exists +- * and has an "enable-method" property that selects the SMP +- * operations defined herein. +- */ +- node = of_find_node_by_path("/cpus"); +- BUG_ON(!node); +- +- /* +- * Our secondary enable method requires a "secondary-boot-reg" +- * property to specify a register address used to request the +- * ROM code boot a secondary code. If we have any trouble +- * getting this we fall back to uniprocessor mode. +- */ +- if (of_property_read_u32(node, OF_SECONDARY_BOOT, &secondary_boot)) { +- pr_err("%s: missing/invalid " OF_SECONDARY_BOOT " property\n", +- node->name); +- ret = -ENOENT; /* Arrange to disable SMP */ +- goto out; +- } +- +- /* +- * Enable the SCU on Cortex A9 based SoCs. If -ENOENT is +- * returned, the SoC reported a uniprocessor configuration. +- * We bail on any other error. +- */ +- ret = scu_a9_enable(); +-out: +- of_node_put(node); +- if (ret) { +- /* Update the CPU present map to reflect uniprocessor mode */ +- BUG_ON(ret != -ENOENT); +- pr_warn("disabling SMP\n"); +- init_cpu_present(&only_cpu_0); +- } +-} +- +-/* +- * The ROM code has the secondary cores looping, waiting for an event. +- * When an event occurs each core examines the bottom two bits of the +- * secondary boot register. When a core finds those bits contain its +- * own core id, it performs initialization, including computing its boot +- * address by clearing the boot register value's bottom two bits. The +- * core signals that it is beginning its execution by writing its boot +- * address back to the secondary boot register, and finally jumps to +- * that address. +- * +- * So to start a core executing we need to: +- * - Encode the (hardware) CPU id with the bottom bits of the secondary +- * start address. +- * - Write that value into the secondary boot register. +- * - Generate an event to wake up the secondary CPU(s). +- * - Wait for the secondary boot register to be re-written, which +- * indicates the secondary core has started. +- */ +-static int bcm_boot_secondary(unsigned int cpu, struct task_struct *idle) +-{ +- void __iomem *boot_reg; +- phys_addr_t boot_func; +- u64 start_clock; +- u32 cpu_id; +- u32 boot_val; +- bool timeout = false; +- +- cpu_id = cpu_logical_map(cpu); +- if (cpu_id & ~BOOT_ADDR_CPUID_MASK) { +- pr_err("bad cpu id (%u > %u)\n", cpu_id, BOOT_ADDR_CPUID_MASK); +- return -EINVAL; +- } +- +- if (!secondary_boot) { +- pr_err("required secondary boot register not specified\n"); +- return -EINVAL; +- } +- +- boot_reg = ioremap_nocache((phys_addr_t)secondary_boot, sizeof(u32)); +- if (!boot_reg) { +- pr_err("unable to map boot register for cpu %u\n", cpu_id); +- return -ENOSYS; +- } +- +- /* +- * Secondary cores will start in secondary_startup(), +- * defined in "arch/arm/kernel/head.S" +- */ +- boot_func = virt_to_phys(secondary_startup); +- BUG_ON(boot_func & BOOT_ADDR_CPUID_MASK); +- BUG_ON(boot_func > (phys_addr_t)U32_MAX); +- +- /* The core to start is encoded in the low bits */ +- boot_val = (u32)boot_func | cpu_id; +- writel_relaxed(boot_val, boot_reg); +- +- sev(); +- +- /* The low bits will be cleared once the core has started */ +- start_clock = local_clock(); +- while (!timeout && readl_relaxed(boot_reg) == boot_val) +- timeout = local_clock() - start_clock > SECONDARY_TIMEOUT_NS; +- +- iounmap(boot_reg); +- +- if (!timeout) +- return 0; +- +- pr_err("timeout waiting for cpu %u to start\n", cpu_id); +- +- return -ENOSYS; +-} +- +-static struct smp_operations bcm_smp_ops __initdata = { +- .smp_prepare_cpus = bcm_smp_prepare_cpus, +- .smp_boot_secondary = bcm_boot_secondary, +-}; +-CPU_METHOD_OF_DECLARE(bcm_smp_bcm281xx, "brcm,bcm11351-cpu-method", +- &bcm_smp_ops); +--- /dev/null ++++ b/arch/arm/mach-bcm/platsmp.c +@@ -0,0 +1,326 @@ ++/* ++ * Copyright (C) 2014-2015 Broadcom Corporation ++ * Copyright 2014 Linaro Limited ++ * ++ * This program is free software; you can redistribute it and/or ++ * modify it under the terms of the GNU General Public License as ++ * published by the Free Software Foundation version 2. ++ * ++ * This program is distributed "as is" WITHOUT ANY WARRANTY of any ++ * kind, whether express or implied; without even the implied warranty ++ * of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the ++ * GNU General Public License for more details. ++ */ ++ ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++ ++#include ++#include ++#include ++#include ++ ++#include "bcm_nsp.h" ++ ++/* Size of mapped Cortex A9 SCU address space */ ++#define CORTEX_A9_SCU_SIZE 0x58 ++ ++#define SECONDARY_TIMEOUT_NS NSEC_PER_MSEC /* 1 msec (in nanoseconds) */ ++#define BOOT_ADDR_CPUID_MASK 0x3 ++ ++/* Name of device node property defining secondary boot register location */ ++#define OF_SECONDARY_BOOT "secondary-boot-reg" ++ ++/* I/O address of register used to coordinate secondary core startup */ ++static u32 secondary_boot; ++ ++static DEFINE_SPINLOCK(boot_lock); ++ ++/* ++ * Write pen_release in a way that is guaranteed to be visible to all ++ * observers, irrespective of whether they're taking part in coherency ++ * or not. This is necessary for the hotplug code to work reliably. ++ */ ++static void write_pen_release(int val) ++{ ++ pen_release = val; ++ /* ++ * Ensure write to pen_release is visible to the other cores, ++ * here - primary core ++ */ ++ smp_wmb(); ++ sync_cache_w(&pen_release); ++} ++ ++/* ++ * Enable the Cortex A9 Snoop Control Unit ++ * ++ * By the time this is called we already know there are multiple ++ * cores present. We assume we're running on a Cortex A9 processor, ++ * so any trouble getting the base address register or getting the ++ * SCU base is a problem. ++ * ++ * Return 0 if successful or an error code otherwise. ++ */ ++static int __init scu_a9_enable(void) ++{ ++ unsigned long config_base; ++ void __iomem *scu_base; ++ ++ if (!scu_a9_has_base()) { ++ pr_err("no configuration base address register!\n"); ++ return -ENXIO; ++ } ++ ++ /* Config base address register value is zero for uniprocessor */ ++ config_base = scu_a9_get_base(); ++ if (!config_base) { ++ pr_err("hardware reports only one core\n"); ++ return -ENOENT; ++ } ++ ++ scu_base = ioremap((phys_addr_t)config_base, CORTEX_A9_SCU_SIZE); ++ if (!scu_base) { ++ pr_err("failed to remap config base (%lu/%u) for SCU\n", ++ config_base, CORTEX_A9_SCU_SIZE); ++ return -ENOMEM; ++ } ++ ++ scu_enable(scu_base); ++ ++ iounmap(scu_base); /* That's the last we'll need of this */ ++ ++ return 0; ++} ++ ++static int nsp_write_lut(void (*secondary_startup) (void)) ++{ ++ void __iomem *sku_rom_lut; ++ phys_addr_t secondary_startup_phy; ++ ++ if (!secondary_boot) { ++ pr_warn("required secondary boot register not specified\n"); ++ return -EINVAL; ++ } ++ ++ sku_rom_lut = ioremap_nocache((phys_addr_t)secondary_boot, ++ sizeof(secondary_boot)); ++ if (!sku_rom_lut) { ++ pr_warn("unable to ioremap SKU-ROM LUT register\n"); ++ return -ENOMEM; ++ } ++ ++ secondary_startup_phy = virt_to_phys(secondary_startup); ++ BUG_ON(secondary_startup_phy > (phys_addr_t)U32_MAX); ++ ++ writel_relaxed(secondary_startup_phy, sku_rom_lut); ++ /* ++ * Ensure the write is visible to the secondary core. ++ */ ++ smp_wmb(); ++ ++ iounmap(sku_rom_lut); ++ ++ return 0; ++} ++ ++static void nsp_secondary_init(unsigned int cpu) ++{ ++ /* ++ * Let the primary cpu know we are out of holding pen. ++ */ ++ write_pen_release(-1); ++ ++ /* ++ * Synchronise with the boot thread. ++ */ ++ spin_lock(&boot_lock); ++ spin_unlock(&boot_lock); ++} ++ ++static void __init bcm_smp_prepare_cpus(unsigned int max_cpus) ++{ ++ static cpumask_t only_cpu_0 = { CPU_BITS_CPU0 }; ++ struct device_node *node; ++ int ret; ++ ++ BUG_ON(secondary_boot); /* We're called only once */ ++ ++ /* ++ * This function is only called via smp_ops->smp_prepare_cpu(). ++ * That only happens if a "/cpus" device tree node exists ++ * and has an "enable-method" property that selects the SMP ++ * operations defined herein. ++ */ ++ node = of_find_node_by_path("/cpus"); ++ BUG_ON(!node); ++ ++ /* ++ * Our secondary enable method requires a "secondary-boot-reg" ++ * property to specify a register address used to request the ++ * ROM code boot a secondary core. If we have any trouble ++ * getting this we fall back to uniprocessor mode. ++ */ ++ if (of_property_read_u32(node, OF_SECONDARY_BOOT, &secondary_boot)) { ++ pr_warn("%s: missing/invalid " OF_SECONDARY_BOOT " property\n", ++ node->name); ++ ret = -ENOENT; /* Arrange to disable SMP */ ++ goto out; ++ } ++ ++ /* ++ * Enable the SCU on Cortex A9 based SoCs. If -ENOENT is ++ * returned, the SoC reported a uniprocessor configuration. ++ * We bail on any other error. ++ */ ++ ret = scu_a9_enable(); ++out: ++ of_node_put(node); ++ if (ret) { ++ /* Update the CPU present map to reflect uniprocessor mode */ ++ pr_warn("disabling SMP\n"); ++ init_cpu_present(&only_cpu_0); ++ } ++} ++ ++/* ++ * The ROM code has the secondary cores looping, waiting for an event. ++ * When an event occurs each core examines the bottom two bits of the ++ * secondary boot register. When a core finds those bits contain its ++ * own core id, it performs initialization, including computing its boot ++ * address by clearing the boot register value's bottom two bits. The ++ * core signals that it is beginning its execution by writing its boot ++ * address back to the secondary boot register, and finally jumps to ++ * that address. ++ * ++ * So to start a core executing we need to: ++ * - Encode the (hardware) CPU id with the bottom bits of the secondary ++ * start address. ++ * - Write that value into the secondary boot register. ++ * - Generate an event to wake up the secondary CPU(s). ++ * - Wait for the secondary boot register to be re-written, which ++ * indicates the secondary core has started. ++ */ ++static int kona_boot_secondary(unsigned int cpu, struct task_struct *idle) ++{ ++ void __iomem *boot_reg; ++ phys_addr_t boot_func; ++ u64 start_clock; ++ u32 cpu_id; ++ u32 boot_val; ++ bool timeout = false; ++ ++ cpu_id = cpu_logical_map(cpu); ++ if (cpu_id & ~BOOT_ADDR_CPUID_MASK) { ++ pr_err("bad cpu id (%u > %u)\n", cpu_id, BOOT_ADDR_CPUID_MASK); ++ return -EINVAL; ++ } ++ ++ if (!secondary_boot) { ++ pr_err("required secondary boot register not specified\n"); ++ return -EINVAL; ++ } ++ ++ boot_reg = ioremap_nocache((phys_addr_t)secondary_boot, sizeof(u32)); ++ if (!boot_reg) { ++ pr_err("unable to map boot register for cpu %u\n", cpu_id); ++ return -ENOMEM; ++ } ++ ++ /* ++ * Secondary cores will start in secondary_startup(), ++ * defined in "arch/arm/kernel/head.S" ++ */ ++ boot_func = virt_to_phys(secondary_startup); ++ BUG_ON(boot_func & BOOT_ADDR_CPUID_MASK); ++ BUG_ON(boot_func > (phys_addr_t)U32_MAX); ++ ++ /* The core to start is encoded in the low bits */ ++ boot_val = (u32)boot_func | cpu_id; ++ writel_relaxed(boot_val, boot_reg); ++ ++ sev(); ++ ++ /* The low bits will be cleared once the core has started */ ++ start_clock = local_clock(); ++ while (!timeout && readl_relaxed(boot_reg) == boot_val) ++ timeout = local_clock() - start_clock > SECONDARY_TIMEOUT_NS; ++ ++ iounmap(boot_reg); ++ ++ if (!timeout) ++ return 0; ++ ++ pr_err("timeout waiting for cpu %u to start\n", cpu_id); ++ ++ return -ENXIO; ++} ++ ++static int nsp_boot_secondary(unsigned int cpu, struct task_struct *idle) ++{ ++ unsigned long timeout; ++ int ret; ++ ++ /* ++ * After wake up, secondary core branches to the startup ++ * address programmed at SKU ROM LUT location. ++ */ ++ ret = nsp_write_lut(nsp_secondary_startup); ++ if (ret) { ++ pr_err("unable to write startup addr to SKU ROM LUT\n"); ++ goto out; ++ } ++ ++ /* ++ * The secondary processor is waiting to be released from ++ * the holding pen - release it, then wait for it to flag ++ * that it has been released by resetting pen_release. ++ */ ++ spin_lock(&boot_lock); ++ ++ write_pen_release(cpu_logical_map(cpu)); ++ /* ++ * Send an Event to wake up the secondary core which is in ++ * WFE state. Updated pen_release should also be visible to ++ * the secondary core. ++ */ ++ dsb_sev(); ++ ++ timeout = jiffies + (1 * HZ); ++ while (time_before(jiffies, timeout)) { ++ /* Make sure loads on other CPU is visible */ ++ smp_rmb(); ++ if (pen_release == -1) ++ break; ++ ++ udelay(10); ++ } ++ ++ spin_unlock(&boot_lock); ++ ++ ret = pen_release != -1 ? -ENXIO : 0; ++ ++out: ++ return ret; ++} ++ ++static struct smp_operations bcm_smp_ops __initdata = { ++ .smp_prepare_cpus = bcm_smp_prepare_cpus, ++ .smp_boot_secondary = kona_boot_secondary, ++}; ++CPU_METHOD_OF_DECLARE(bcm_smp_bcm281xx, "brcm,bcm11351-cpu-method", ++ &bcm_smp_ops); ++ ++struct smp_operations nsp_smp_ops __initdata = { ++ .smp_prepare_cpus = bcm_smp_prepare_cpus, ++ .smp_secondary_init = nsp_secondary_init, ++ .smp_boot_secondary = nsp_boot_secondary, ++}; ++CPU_METHOD_OF_DECLARE(bcm_smp_nsp, "brcm,bcm-nsp-smp", &nsp_smp_ops); diff --git a/target/linux/bcm53xx/patches-4.3/131-ARM-BCM-Add-SMP-support-for-Broadcom-4708.patch b/target/linux/bcm53xx/patches-4.3/131-ARM-BCM-Add-SMP-support-for-Broadcom-4708.patch new file mode 100644 index 0000000000..ad1c771df7 --- /dev/null +++ b/target/linux/bcm53xx/patches-4.3/131-ARM-BCM-Add-SMP-support-for-Broadcom-4708.patch @@ -0,0 +1,50 @@ +From ddbf0ad85be06948dd214c7beb7b315ef2749e65 Mon Sep 17 00:00:00 2001 +From: Jon Mason +Date: Thu, 15 Oct 2015 14:14:10 -0400 +Subject: [PATCH] ARM: BCM: Add SMP support for Broadcom 4708 + +ARM: BCM: Add SMP support for Broadcom 4708 + +Add SMP support for Broadcom's 4708 SoCs. + +Signed-off-by: Jon Mason +--- + arch/arm/boot/dts/bcm4708.dtsi | 2 ++ + arch/arm/mach-bcm/Kconfig | 2 ++ + arch/arm/mach-bcm/Makefile | 3 +++ + 3 files changed, 7 insertions(+) + +--- a/arch/arm/boot/dts/bcm4708.dtsi ++++ b/arch/arm/boot/dts/bcm4708.dtsi +@@ -15,6 +15,8 @@ + cpus { + #address-cells = <1>; + #size-cells = <0>; ++ enable-method = "brcm,bcm-nsp-smp"; ++ secondary-boot-reg = <0xffff0400>; + + cpu@0 { + device_type = "cpu"; +--- a/arch/arm/mach-bcm/Kconfig ++++ b/arch/arm/mach-bcm/Kconfig +@@ -38,6 +38,8 @@ config ARCH_BCM_CYGNUS + config ARCH_BCM_5301X + bool "Broadcom BCM470X / BCM5301X ARM SoC" if ARCH_MULTI_V7 + select ARCH_BCM_IPROC ++ select ARM_ERRATA_764369 if SMP ++ select HAVE_SMP + help + Support for Broadcom BCM470X and BCM5301X SoCs with ARM CPU cores. + +--- a/arch/arm/mach-bcm/Makefile ++++ b/arch/arm/mach-bcm/Makefile +@@ -36,6 +36,9 @@ obj-$(CONFIG_ARCH_BCM2835) += board_bcm2 + + # BCM5301X + obj-$(CONFIG_ARCH_BCM_5301X) += bcm_5301x.o ++ifeq ($(CONFIG_ARCH_BCM_5301X),y) ++obj-$(CONFIG_SMP) += headsmp.o platsmp.o ++endif + + # BCM63XXx + ifeq ($(CONFIG_ARCH_BCM_63XX),y) diff --git a/target/linux/bcm53xx/patches-4.3/190-usb-xhci-plat-fix-adding-usb3-lpm-capable-quirk.patch b/target/linux/bcm53xx/patches-4.3/190-usb-xhci-plat-fix-adding-usb3-lpm-capable-quirk.patch new file mode 100644 index 0000000000..a769650e3f --- /dev/null +++ b/target/linux/bcm53xx/patches-4.3/190-usb-xhci-plat-fix-adding-usb3-lpm-capable-quirk.patch @@ -0,0 +1,63 @@ +From 1420e53fc88673683f8990aa5342e7b2640ce165 Mon Sep 17 00:00:00 2001 +From: Hauke Mehrtens +Date: Sun, 18 Oct 2015 19:13:27 +0200 +Subject: [PATCH v3 1/6] usb: xhci: plat: fix adding usb3-lpm-capable quirk + +The xhci->quirks member is overwritten in xhci_gen_setup() with the +quirks given through the module load parameter. Without this patch the +usb3-lpm-capable quirk will be over written before it gets used. This +patch moves the quirks code to the xhci_plat_quirks() callback function +which gets called directly after the quirks member variable is +overwritten with the module load parameter. + +I do not have any hardware which is using usb3-lpm-capabls so I can not +test this on real hardware. + +Signed-off-by: Hauke Mehrtens +--- + drivers/usb/host/xhci-plat.c | 14 ++++++++------ + 1 file changed, 8 insertions(+), 6 deletions(-) + +--- a/drivers/usb/host/xhci-plat.c ++++ b/drivers/usb/host/xhci-plat.c +@@ -37,12 +37,20 @@ static const struct xhci_driver_override + + static void xhci_plat_quirks(struct device *dev, struct xhci_hcd *xhci) + { ++ struct platform_device *pdev = to_platform_device(dev); ++ struct device_node *node = pdev->dev.of_node; ++ struct usb_xhci_pdata *pdata = dev_get_platdata(&pdev->dev); ++ + /* + * As of now platform drivers don't provide MSI support so we ensure + * here that the generic code does not try to make a pci_dev from our + * dev struct in order to setup MSI + */ + xhci->quirks |= XHCI_PLAT; ++ ++ if ((node && of_property_read_bool(node, "usb3-lpm-capable")) || ++ (pdata && pdata->usb3_lpm_capable)) ++ xhci->quirks |= XHCI_LPM_SUPPORT; + } + + /* called during probe() after chip reset completes */ +@@ -74,8 +82,6 @@ static int xhci_plat_start(struct usb_hc + + static int xhci_plat_probe(struct platform_device *pdev) + { +- struct device_node *node = pdev->dev.of_node; +- struct usb_xhci_pdata *pdata = dev_get_platdata(&pdev->dev); + const struct hc_driver *driver; + struct xhci_hcd *xhci; + struct resource *res; +@@ -148,10 +154,6 @@ static int xhci_plat_probe(struct platfo + goto disable_clk; + } + +- if ((node && of_property_read_bool(node, "usb3-lpm-capable")) || +- (pdata && pdata->usb3_lpm_capable)) +- xhci->quirks |= XHCI_LPM_SUPPORT; +- + if (HCC_MAX_PSA(xhci->hcc_params) >= 4) + xhci->shared_hcd->can_do_streams = 1; + diff --git a/target/linux/bcm53xx/patches-4.3/191-usb-xhci-add-Broadcom-specific-fake-doorbell.patch b/target/linux/bcm53xx/patches-4.3/191-usb-xhci-add-Broadcom-specific-fake-doorbell.patch new file mode 100644 index 0000000000..ae70f429e9 --- /dev/null +++ b/target/linux/bcm53xx/patches-4.3/191-usb-xhci-add-Broadcom-specific-fake-doorbell.patch @@ -0,0 +1,135 @@ +From dd0e5f9a6a4aed849bdb80641c2a2350476cede7 Mon Sep 17 00:00:00 2001 +From: =?UTF-8?q?Rafa=C5=82=20Mi=C5=82ecki?= +Date: Sun, 21 Jun 2015 11:10:49 +0200 +Subject: [PATCH v3 2/6] usb: xhci: add Broadcom specific fake doorbell +MIME-Version: 1.0 +Content-Type: text/plain; charset=UTF-8 +Content-Transfer-Encoding: 8bit + +This fixes problem with controller seeing devices only in some small +percentage of cold boots. +This quirk is also added to the platform data so we can activate it +when we register our platform driver. + +Signed-off-by: Rafał Miłecki +Signed-off-by: Hauke Mehrtens +--- + drivers/usb/host/xhci-plat.c | 3 +++ + drivers/usb/host/xhci.c | 57 +++++++++++++++++++++++++++++++++++++--- + drivers/usb/host/xhci.h | 1 + + include/linux/usb/xhci_pdriver.h | 1 + + 4 files changed, 59 insertions(+), 3 deletions(-) + +--- a/drivers/usb/host/xhci-plat.c ++++ b/drivers/usb/host/xhci-plat.c +@@ -51,6 +51,9 @@ static void xhci_plat_quirks(struct devi + if ((node && of_property_read_bool(node, "usb3-lpm-capable")) || + (pdata && pdata->usb3_lpm_capable)) + xhci->quirks |= XHCI_LPM_SUPPORT; ++ ++ if (pdata && pdata->usb3_fake_doorbell) ++ xhci->quirks |= XHCI_FAKE_DOORBELL; + } + + /* called during probe() after chip reset completes */ +--- a/drivers/usb/host/xhci.c ++++ b/drivers/usb/host/xhci.c +@@ -121,6 +121,39 @@ int xhci_halt(struct xhci_hcd *xhci) + return ret; + } + ++static int xhci_fake_doorbell(struct xhci_hcd *xhci, int slot_id) ++{ ++ u32 temp; ++ ++ /* alloc a virt device for slot */ ++ if (!xhci_alloc_virt_device(xhci, slot_id, NULL, GFP_NOIO)) { ++ xhci_warn(xhci, "Could not allocate xHCI USB device data structures\n"); ++ return -ENOMEM; ++ } ++ ++ /* ring fake doorbell for slot_id ep 0 */ ++ xhci_ring_ep_doorbell(xhci, slot_id, 0, 0); ++ usleep_range(1000, 1500); ++ ++ /* read the status register to check if HSE is set or not? */ ++ temp = readl(&xhci->op_regs->status); ++ ++ /* clear HSE if set */ ++ if (temp & STS_FATAL) { ++ xhci_dbg(xhci, "HSE problem detected, status: 0x%x\n", temp); ++ temp &= ~(0x1fff); ++ temp |= STS_FATAL; ++ writel(temp, &xhci->op_regs->status); ++ usleep_range(1000, 1500); ++ readl(&xhci->op_regs->status); ++ } ++ ++ /* Free virt device */ ++ xhci_free_virt_device(xhci, slot_id); ++ ++ return 0; ++} ++ + /* + * Set the run bit and wait for the host to be running. + */ +@@ -557,10 +590,25 @@ int xhci_init(struct usb_hcd *hcd) + + static int xhci_run_finished(struct xhci_hcd *xhci) + { +- if (xhci_start(xhci)) { +- xhci_halt(xhci); +- return -ENODEV; ++ int err; ++ ++ err = xhci_start(xhci); ++ if (err) { ++ err = -ENODEV; ++ goto out_err; ++ } ++ if (xhci->quirks & XHCI_FAKE_DOORBELL) { ++ err = xhci_fake_doorbell(xhci, 1); ++ if (err) ++ goto out_err; ++ ++ err = xhci_start(xhci); ++ if (err) { ++ err = -ENODEV; ++ goto out_err; ++ } + } ++ + xhci->shared_hcd->state = HC_STATE_RUNNING; + xhci->cmd_ring_state = CMD_RING_STATE_RUNNING; + +@@ -570,6 +618,9 @@ static int xhci_run_finished(struct xhci + xhci_dbg_trace(xhci, trace_xhci_dbg_init, + "Finished xhci_run for USB3 roothub"); + return 0; ++out_err: ++ xhci_halt(xhci); ++ return err; + } + + /* +--- a/drivers/usb/host/xhci.h ++++ b/drivers/usb/host/xhci.h +@@ -1575,6 +1575,7 @@ struct xhci_hcd { + /* For controllers with a broken beyond repair streams implementation */ + #define XHCI_BROKEN_STREAMS (1 << 19) + #define XHCI_PME_STUCK_QUIRK (1 << 20) ++#define XHCI_FAKE_DOORBELL (1 << 21) + unsigned int num_active_eps; + unsigned int limit_active_eps; + /* There are two roothubs to keep track of bus suspend info for */ +--- a/include/linux/usb/xhci_pdriver.h ++++ b/include/linux/usb/xhci_pdriver.h +@@ -22,6 +22,7 @@ + */ + struct usb_xhci_pdata { + unsigned usb3_lpm_capable:1; ++ unsigned usb3_fake_doorbell:1; + }; + + #endif /* __USB_CORE_XHCI_PDRIVER_H */ diff --git a/target/linux/bcm53xx/patches-4.3/195-USB-bcma-make-helper-creating-platform-dev-more-gene.patch b/target/linux/bcm53xx/patches-4.3/195-USB-bcma-make-helper-creating-platform-dev-more-gene.patch new file mode 100644 index 0000000000..1e28857655 --- /dev/null +++ b/target/linux/bcm53xx/patches-4.3/195-USB-bcma-make-helper-creating-platform-dev-more-gene.patch @@ -0,0 +1,75 @@ +From c7c7bf7fcbacadac7781783de25fe1e13e2a2c35 Mon Sep 17 00:00:00 2001 +From: =?UTF-8?q?Rafa=C5=82=20Mi=C5=82ecki?= +Date: Tue, 16 Jun 2015 12:33:46 +0200 +Subject: [PATCH v3 3/6] usb: bcma: make helper creating platform dev more + generic +MIME-Version: 1.0 +Content-Type: text/plain; charset=UTF-8 +Content-Transfer-Encoding: 8bit + +Having "bool ohci" argument bounded us to two cases only and didn't +allow re-using this code for XHCI. + +Signed-off-by: Rafał Miłecki +Signed-off-by: Hauke Mehrtens +--- + drivers/usb/host/bcma-hcd.c | 24 +++++++++++++----------- + 1 file changed, 13 insertions(+), 11 deletions(-) + +--- a/drivers/usb/host/bcma-hcd.c ++++ b/drivers/usb/host/bcma-hcd.c +@@ -249,7 +249,10 @@ static const struct usb_ehci_pdata ehci_ + static const struct usb_ohci_pdata ohci_pdata = { + }; + +-static struct platform_device *bcma_hcd_create_pdev(struct bcma_device *dev, bool ohci, u32 addr) ++static struct platform_device *bcma_hcd_create_pdev(struct bcma_device *dev, ++ const char *name, u32 addr, ++ const void *data, ++ size_t size) + { + struct platform_device *hci_dev; + struct resource hci_res[2]; +@@ -264,8 +267,7 @@ static struct platform_device *bcma_hcd_ + hci_res[1].start = dev->irq; + hci_res[1].flags = IORESOURCE_IRQ; + +- hci_dev = platform_device_alloc(ohci ? "ohci-platform" : +- "ehci-platform" , 0); ++ hci_dev = platform_device_alloc(name, 0); + if (!hci_dev) + return ERR_PTR(-ENOMEM); + +@@ -276,12 +278,8 @@ static struct platform_device *bcma_hcd_ + ARRAY_SIZE(hci_res)); + if (ret) + goto err_alloc; +- if (ohci) +- ret = platform_device_add_data(hci_dev, &ohci_pdata, +- sizeof(ohci_pdata)); +- else +- ret = platform_device_add_data(hci_dev, &ehci_pdata, +- sizeof(ehci_pdata)); ++ if (data) ++ ret = platform_device_add_data(hci_dev, data, size); + if (ret) + goto err_alloc; + ret = platform_device_add(hci_dev); +@@ -334,11 +332,15 @@ static int bcma_hcd_probe(struct bcma_de + && chipinfo->rev == 0) + ohci_addr = 0x18009000; + +- usb_dev->ohci_dev = bcma_hcd_create_pdev(dev, true, ohci_addr); ++ usb_dev->ohci_dev = bcma_hcd_create_pdev(dev, "ohci-platform", ++ ohci_addr, &ohci_pdata, ++ sizeof(ohci_pdata)); + if (IS_ERR(usb_dev->ohci_dev)) + return PTR_ERR(usb_dev->ohci_dev); + +- usb_dev->ehci_dev = bcma_hcd_create_pdev(dev, false, dev->addr); ++ usb_dev->ehci_dev = bcma_hcd_create_pdev(dev, "ehci-platform", ++ dev->addr, &ehci_pdata, ++ sizeof(ehci_pdata)); + if (IS_ERR(usb_dev->ehci_dev)) { + err = PTR_ERR(usb_dev->ehci_dev); + goto err_unregister_ohci_dev; diff --git a/target/linux/bcm53xx/patches-4.3/196-USB-bcma-use-separated-function-for-USB-2.0-initiali.patch b/target/linux/bcm53xx/patches-4.3/196-USB-bcma-use-separated-function-for-USB-2.0-initiali.patch new file mode 100644 index 0000000000..d636e86046 --- /dev/null +++ b/target/linux/bcm53xx/patches-4.3/196-USB-bcma-use-separated-function-for-USB-2.0-initiali.patch @@ -0,0 +1,104 @@ +From fa5622c2fadae573dd6b0f5bffe436b230b411f6 Mon Sep 17 00:00:00 2001 +From: =?UTF-8?q?Rafa=C5=82=20Mi=C5=82ecki?= +Date: Tue, 16 Jun 2015 12:52:07 +0200 +Subject: [PATCH v3 4/6] usb: bcma: use separated function for USB 2.0 + initialization +MIME-Version: 1.0 +Content-Type: text/plain; charset=UTF-8 +Content-Transfer-Encoding: 8bit + +This will allow adding USB 3.0 (XHCI) support cleanly. + +Signed-off-by: Rafał Miłecki +Signed-off-by: Hauke Mehrtens +--- + drivers/usb/host/bcma-hcd.c | 51 +++++++++++++++++++++++++++++++-------------- + 1 file changed, 35 insertions(+), 16 deletions(-) + +--- a/drivers/usb/host/bcma-hcd.c ++++ b/drivers/usb/host/bcma-hcd.c +@@ -34,6 +34,7 @@ MODULE_DESCRIPTION("Common USB driver fo + MODULE_LICENSE("GPL"); + + struct bcma_hcd_device { ++ struct bcma_device *core; + struct platform_device *ehci_dev; + struct platform_device *ohci_dev; + }; +@@ -293,27 +294,16 @@ err_alloc: + return ERR_PTR(ret); + } + +-static int bcma_hcd_probe(struct bcma_device *dev) ++static int bcma_hcd_usb20_init(struct bcma_hcd_device *usb_dev) + { +- int err; ++ struct bcma_device *dev = usb_dev->core; ++ struct bcma_chipinfo *chipinfo = &dev->bus->chipinfo; + u32 ohci_addr; +- struct bcma_hcd_device *usb_dev; +- struct bcma_chipinfo *chipinfo; +- +- chipinfo = &dev->bus->chipinfo; +- +- /* TODO: Probably need checks here; is the core connected? */ ++ int err; + + if (dma_set_mask_and_coherent(dev->dma_dev, DMA_BIT_MASK(32))) + return -EOPNOTSUPP; + +- usb_dev = devm_kzalloc(&dev->dev, sizeof(struct bcma_hcd_device), +- GFP_KERNEL); +- if (!usb_dev) +- return -ENOMEM; +- +- bcma_hci_platform_power_gpio(dev, true); +- + switch (dev->id.id) { + case BCMA_CORE_NS_USB20: + bcma_hcd_init_chip_arm(dev); +@@ -346,7 +336,6 @@ static int bcma_hcd_probe(struct bcma_de + goto err_unregister_ohci_dev; + } + +- bcma_set_drvdata(dev, usb_dev); + return 0; + + err_unregister_ohci_dev: +@@ -354,6 +343,36 @@ err_unregister_ohci_dev: + return err; + } + ++static int bcma_hcd_probe(struct bcma_device *dev) ++{ ++ int err; ++ struct bcma_hcd_device *usb_dev; ++ ++ /* TODO: Probably need checks here; is the core connected? */ ++ ++ usb_dev = devm_kzalloc(&dev->dev, sizeof(struct bcma_hcd_device), ++ GFP_KERNEL); ++ if (!usb_dev) ++ return -ENOMEM; ++ usb_dev->core = dev; ++ ++ bcma_hci_platform_power_gpio(dev, true); ++ ++ switch (dev->id.id) { ++ case BCMA_CORE_USB20_HOST: ++ case BCMA_CORE_NS_USB20: ++ err = bcma_hcd_usb20_init(usb_dev); ++ if (err) ++ return err; ++ break; ++ default: ++ return -ENODEV; ++ } ++ ++ bcma_set_drvdata(dev, usb_dev); ++ return 0; ++} ++ + static void bcma_hcd_remove(struct bcma_device *dev) + { + struct bcma_hcd_device *usb_dev = bcma_get_drvdata(dev); diff --git a/target/linux/bcm53xx/patches-4.3/197-USB-bcma-add-USB-3.0-support.patch b/target/linux/bcm53xx/patches-4.3/197-USB-bcma-add-USB-3.0-support.patch new file mode 100644 index 0000000000..f477a1b65d --- /dev/null +++ b/target/linux/bcm53xx/patches-4.3/197-USB-bcma-add-USB-3.0-support.patch @@ -0,0 +1,295 @@ +From 121ec6539abedbc0e975cf35f48ee044b323e4c3 Mon Sep 17 00:00:00 2001 +From: =?UTF-8?q?Rafa=C5=82=20Mi=C5=82ecki?= +Date: Tue, 16 Jun 2015 17:14:26 +0200 +Subject: [PATCH v3 5/6] usb: bcma: add USB 3.0 support +MIME-Version: 1.0 +Content-Type: text/plain; charset=UTF-8 +Content-Transfer-Encoding: 8bit + +Signed-off-by: Rafał Miłecki +Signed-off-by: Hauke Mehrtens +--- + drivers/usb/host/bcma-hcd.c | 225 ++++++++++++++++++++++++++++++++++++++++++++ + 1 file changed, 225 insertions(+) + +--- a/drivers/usb/host/bcma-hcd.c ++++ b/drivers/usb/host/bcma-hcd.c +@@ -28,6 +28,7 @@ + #include + #include + #include ++#include + + MODULE_AUTHOR("Hauke Mehrtens"); + MODULE_DESCRIPTION("Common USB driver for BCMA Bus"); +@@ -37,6 +38,7 @@ struct bcma_hcd_device { + struct bcma_device *core; + struct platform_device *ehci_dev; + struct platform_device *ohci_dev; ++ struct platform_device *xhci_dev; + }; + + /* Wait for bitmask in a register to get set or cleared. +@@ -250,6 +252,10 @@ static const struct usb_ehci_pdata ehci_ + static const struct usb_ohci_pdata ohci_pdata = { + }; + ++static const struct usb_xhci_pdata xhci_pdata = { ++ .usb3_fake_doorbell = 1 ++}; ++ + static struct platform_device *bcma_hcd_create_pdev(struct bcma_device *dev, + const char *name, u32 addr, + const void *data, +@@ -343,6 +349,216 @@ err_unregister_ohci_dev: + return err; + } + ++static bool bcma_wait_reg(struct bcma_bus *bus, void __iomem *addr, u32 mask, ++ u32 value, int timeout) ++{ ++ unsigned long deadline = jiffies + timeout; ++ u32 val; ++ ++ do { ++ val = readl(addr); ++ if ((val & mask) == value) ++ return true; ++ cpu_relax(); ++ udelay(10); ++ } while (!time_after_eq(jiffies, deadline)); ++ ++ pr_err("Timeout waiting for register %p\n", addr); ++ ++ return false; ++} ++ ++static void bcma_hcd_usb30_phy_init(struct bcma_hcd_device *bcma_hcd) ++{ ++ struct bcma_device *core = bcma_hcd->core; ++ struct bcma_bus *bus = core->bus; ++ struct bcma_chipinfo *chipinfo = &bus->chipinfo; ++ struct bcma_drv_cc_b *ccb = &bus->drv_cc_b; ++ struct bcma_device *arm_core; ++ void __iomem *dmu = NULL; ++ u32 cru_straps_ctrl; ++ ++ if (chipinfo->id != BCMA_CHIP_ID_BCM4707 && ++ chipinfo->id != BCMA_CHIP_ID_BCM53018) ++ return; ++ ++ arm_core = bcma_find_core(bus, BCMA_CORE_ARMCA9); ++ if (!arm_core) ++ return; ++ ++ dmu = ioremap_nocache(arm_core->addr_s[0], 0x1000); ++ if (!dmu) ++ goto out; ++ ++ /* Check strapping of PCIE/USB3 SEL */ ++ cru_straps_ctrl = ioread32(dmu + 0x2a0); ++ if ((cru_straps_ctrl & 0x10) == 0) ++ goto out; ++ ++ /* Perform USB3 system soft reset */ ++ bcma_awrite32(core, BCMA_RESET_CTL, BCMA_RESET_CTL_RESET); ++ ++ /* Enable MDIO. Setting MDCDIV as 26 */ ++ iowrite32(0x0000009a, ccb->mii + 0x000); ++ udelay(2); ++ ++ switch (chipinfo->id) { ++ case BCMA_CHIP_ID_BCM4707: ++ if (chipinfo->rev == 4) { ++ /* For NS-B0, USB3 PLL Block */ ++ bcma_wait_reg(bus, ccb->mii + 0x000, 0x0100, 0x0000, 1000); ++ iowrite32(0x587e8000, ccb->mii + 0x004); ++ ++ /* Clear ana_pllSeqStart */ ++ bcma_wait_reg(bus, ccb->mii + 0x000, 0x0100, 0x0000, 1000); ++ iowrite32(0x58061000, ccb->mii + 0x004); ++ ++ /* CMOS Divider ratio to 25 */ ++ bcma_wait_reg(bus, ccb->mii + 0x000, 0x0100, 0x0000, 1000); ++ iowrite32(0x582a6400, ccb->mii + 0x004); ++ ++ /* Asserting PLL Reset */ ++ bcma_wait_reg(bus, ccb->mii + 0x000, 0x0100, 0x0000, 1000); ++ iowrite32(0x582ec000, ccb->mii + 0x004); ++ ++ /* Deaaserting PLL Reset */ ++ bcma_wait_reg(bus, ccb->mii + 0x000, 0x0100, 0x0000, 1000); ++ iowrite32(0x582e8000, ccb->mii + 0x004); ++ ++ /* Deasserting USB3 system reset */ ++ bcma_awrite32(core, BCMA_RESET_CTL, 0); ++ ++ /* Set ana_pllSeqStart */ ++ bcma_wait_reg(bus, ccb->mii + 0x000, 0x0100, 0x0000, 1000); ++ iowrite32(0x58069000, ccb->mii + 0x004); ++ ++ /* RXPMD block */ ++ bcma_wait_reg(bus, ccb->mii + 0x000, 0x0100, 0x0000, 1000); ++ iowrite32(0x587e8020, ccb->mii + 0x004); ++ ++ /* CDR int loop locking BW to 1 */ ++ bcma_wait_reg(bus, ccb->mii + 0x000, 0x0100, 0x0000, 1000); ++ iowrite32(0x58120049, ccb->mii + 0x004); ++ ++ /* CDR int loop acquisition BW to 1 */ ++ bcma_wait_reg(bus, ccb->mii + 0x000, 0x0100, 0x0000, 1000); ++ iowrite32(0x580e0049, ccb->mii + 0x004); ++ ++ /* CDR prop loop BW to 1 */ ++ bcma_wait_reg(bus, ccb->mii + 0x000, 0x0100, 0x0000, 1000); ++ iowrite32(0x580a005c, ccb->mii + 0x004); ++ ++ /* Waiting MII Mgt interface idle */ ++ bcma_wait_reg(bus, ccb->mii + 0x000, 0x0100, 0x0000, 1000); ++ } else { ++ /* PLL30 block */ ++ bcma_wait_reg(bus, ccb->mii + 0x000, 0x0100, 0x0000, 1000); ++ iowrite32(0x587e8000, ccb->mii + 0x004); ++ ++ bcma_wait_reg(bus, ccb->mii + 0x000, 0x0100, 0x0000, 1000); ++ iowrite32(0x582a6400, ccb->mii + 0x004); ++ ++ bcma_wait_reg(bus, ccb->mii + 0x000, 0x0100, 0x0000, 1000); ++ iowrite32(0x587e80e0, ccb->mii + 0x004); ++ ++ bcma_wait_reg(bus, ccb->mii + 0x000, 0x0100, 0x0000, 1000); ++ iowrite32(0x580a009c, ccb->mii + 0x004); ++ ++ /* Enable SSC */ ++ bcma_wait_reg(bus, ccb->mii + 0x000, 0x0100, 0x0000, 1000); ++ iowrite32(0x587e8040, ccb->mii + 0x004); ++ ++ bcma_wait_reg(bus, ccb->mii + 0x000, 0x0100, 0x0000, 1000); ++ iowrite32(0x580a21d3, ccb->mii + 0x004); ++ ++ bcma_wait_reg(bus, ccb->mii + 0x000, 0x0100, 0x0000, 1000); ++ iowrite32(0x58061003, ccb->mii + 0x004); ++ ++ /* Waiting MII Mgt interface idle */ ++ bcma_wait_reg(bus, ccb->mii + 0x000, 0x0100, 0x0000, 1000); ++ ++ /* Deasserting USB3 system reset */ ++ bcma_awrite32(core, BCMA_RESET_CTL, 0); ++ } ++ break; ++ case BCMA_CHIP_ID_BCM53018: ++ /* USB3 PLL Block */ ++ bcma_wait_reg(bus, ccb->mii + 0x000, 0x0100, 0x0000, 1000); ++ iowrite32(0x587e8000, ccb->mii + 0x004); ++ ++ /* Assert Ana_Pllseq start */ ++ bcma_wait_reg(bus, ccb->mii + 0x000, 0x0100, 0x0000, 1000); ++ iowrite32(0x58061000, ccb->mii + 0x004); ++ ++ /* Assert CML Divider ratio to 26 */ ++ bcma_wait_reg(bus, ccb->mii + 0x000, 0x0100, 0x0000, 1000); ++ iowrite32(0x582a6400, ccb->mii + 0x004); ++ ++ /* Asserting PLL Reset */ ++ bcma_wait_reg(bus, ccb->mii + 0x000, 0x0100, 0x0000, 1000); ++ iowrite32(0x582ec000, ccb->mii + 0x004); ++ ++ /* Deaaserting PLL Reset */ ++ bcma_wait_reg(bus, ccb->mii + 0x000, 0x0100, 0x0000, 1000); ++ iowrite32(0x582e8000, ccb->mii + 0x004); ++ ++ /* Waiting MII Mgt interface idle */ ++ bcma_wait_reg(bus, ccb->mii + 0x000, 0x0100, 0x0000, 1000); ++ ++ /* Deasserting USB3 system reset */ ++ bcma_awrite32(core, BCMA_RESET_CTL, 0); ++ ++ /* PLL frequency monitor enable */ ++ bcma_wait_reg(bus, ccb->mii + 0x000, 0x0100, 0x0000, 1000); ++ iowrite32(0x58069000, ccb->mii + 0x004); ++ ++ /* PIPE Block */ ++ bcma_wait_reg(bus, ccb->mii + 0x000, 0x0100, 0x0000, 1000); ++ iowrite32(0x587e8060, ccb->mii + 0x004); ++ ++ /* CMPMAX & CMPMINTH setting */ ++ bcma_wait_reg(bus, ccb->mii + 0x000, 0x0100, 0x0000, 1000); ++ iowrite32(0x580af30d, ccb->mii + 0x004); ++ ++ /* DEGLITCH MIN & MAX setting */ ++ bcma_wait_reg(bus, ccb->mii + 0x000, 0x0100, 0x0000, 1000); ++ iowrite32(0x580e6302, ccb->mii + 0x004); ++ ++ /* TXPMD block */ ++ bcma_wait_reg(bus, ccb->mii + 0x000, 0x0100, 0x0000, 1000); ++ iowrite32(0x587e8040, ccb->mii + 0x004); ++ ++ /* Enabling SSC */ ++ bcma_wait_reg(bus, ccb->mii + 0x000, 0x0100, 0x0000, 1000); ++ iowrite32(0x58061003, ccb->mii + 0x004); ++ ++ /* Waiting MII Mgt interface idle */ ++ bcma_wait_reg(bus, ccb->mii + 0x000, 0x0100, 0x0000, 1000); ++ ++ break; ++ } ++out: ++ if (dmu) ++ iounmap(dmu); ++} ++ ++static int bcma_hcd_usb30_init(struct bcma_hcd_device *bcma_hcd) ++{ ++ struct bcma_device *core = bcma_hcd->core; ++ ++ bcma_core_enable(core, 0); ++ ++ bcma_hcd_usb30_phy_init(bcma_hcd); ++ ++ bcma_hcd->xhci_dev = bcma_hcd_create_pdev(core, "xhci-hcd", core->addr, ++ &xhci_pdata, ++ sizeof(xhci_pdata)); ++ if (IS_ERR(bcma_hcd->ohci_dev)) ++ return PTR_ERR(bcma_hcd->ohci_dev); ++ ++ return 0; ++} ++ + static int bcma_hcd_probe(struct bcma_device *dev) + { + int err; +@@ -365,6 +581,11 @@ static int bcma_hcd_probe(struct bcma_de + if (err) + return err; + break; ++ case BCMA_CORE_NS_USB30: ++ err = bcma_hcd_usb30_init(usb_dev); ++ if (err) ++ return err; ++ break; + default: + return -ENODEV; + } +@@ -378,11 +599,14 @@ static void bcma_hcd_remove(struct bcma_ + struct bcma_hcd_device *usb_dev = bcma_get_drvdata(dev); + struct platform_device *ohci_dev = usb_dev->ohci_dev; + struct platform_device *ehci_dev = usb_dev->ehci_dev; ++ struct platform_device *xhci_dev = usb_dev->xhci_dev; + + if (ohci_dev) + platform_device_unregister(ohci_dev); + if (ehci_dev) + platform_device_unregister(ehci_dev); ++ if (xhci_dev) ++ platform_device_unregister(xhci_dev); + + bcma_core_disable(dev, 0); + } +@@ -419,6 +643,7 @@ static int bcma_hcd_resume(struct bcma_d + static const struct bcma_device_id bcma_hcd_table[] = { + BCMA_CORE(BCMA_MANUF_BCM, BCMA_CORE_USB20_HOST, BCMA_ANY_REV, BCMA_ANY_CLASS), + BCMA_CORE(BCMA_MANUF_BCM, BCMA_CORE_NS_USB20, BCMA_ANY_REV, BCMA_ANY_CLASS), ++ BCMA_CORE(BCMA_MANUF_BCM, BCMA_CORE_NS_USB30, BCMA_ANY_REV, BCMA_ANY_CLASS), + {}, + }; + MODULE_DEVICE_TABLE(bcma, bcma_hcd_table); diff --git a/target/linux/bcm53xx/patches-4.3/198-USB-bcma-fix-setting-VCC-GPIO-value.patch b/target/linux/bcm53xx/patches-4.3/198-USB-bcma-fix-setting-VCC-GPIO-value.patch new file mode 100644 index 0000000000..75932937c0 --- /dev/null +++ b/target/linux/bcm53xx/patches-4.3/198-USB-bcma-fix-setting-VCC-GPIO-value.patch @@ -0,0 +1,54 @@ +From 7572673e06393b117f87b20b82be0518634d7042 Mon Sep 17 00:00:00 2001 +From: =?UTF-8?q?Rafa=C5=82=20Mi=C5=82ecki?= +Date: Sun, 21 Jun 2015 12:09:57 +0200 +Subject: [PATCH v3 6/6] usb: bcma: fix setting VCC GPIO value +MIME-Version: 1.0 +Content-Type: text/plain; charset=UTF-8 +Content-Transfer-Encoding: 8bit + +It wasn't working (on most of devices?) without setting GPIO direction +and wasn't respecting ACTIVE_LOW flag. + +Signed-off-by: Rafał Miłecki +Signed-off-by: Hauke Mehrtens +--- + drivers/usb/host/bcma-hcd.c | 14 ++++++++++---- + 1 file changed, 10 insertions(+), 4 deletions(-) + +--- a/drivers/usb/host/bcma-hcd.c ++++ b/drivers/usb/host/bcma-hcd.c +@@ -26,6 +26,7 @@ + #include + #include + #include ++#include + #include + #include + #include +@@ -231,17 +232,22 @@ static void bcma_hcd_init_chip_arm(struc + + static void bcma_hci_platform_power_gpio(struct bcma_device *dev, bool val) + { ++ enum of_gpio_flags of_flags; + int gpio; + +- gpio = of_get_named_gpio(dev->dev.of_node, "vcc-gpio", 0); ++ gpio = of_get_named_gpio_flags(dev->dev.of_node, "vcc-gpio", 0, &of_flags); + if (!gpio_is_valid(gpio)) + return; + + if (val) { +- gpio_request(gpio, "bcma-hcd-gpio"); +- gpio_set_value(gpio, 1); ++ unsigned long flags = 0; ++ bool active_low = !!(of_flags & OF_GPIO_ACTIVE_LOW); ++ ++ flags |= active_low ? GPIOF_ACTIVE_LOW : 0; ++ flags |= active_low ? GPIOF_INIT_LOW : GPIOF_INIT_HIGH; ++ gpio_request_one(gpio, flags, "bcma-hcd-gpio"); + } else { +- gpio_set_value(gpio, 0); ++ gpiod_set_value(gpio_to_desc(gpio), 0); + gpio_free(gpio); + } + } diff --git a/target/linux/bcm53xx/patches-4.3/300-ARM-BCM5301X-Disable-MMU-and-Dcache-for-decompression.patch b/target/linux/bcm53xx/patches-4.3/300-ARM-BCM5301X-Disable-MMU-and-Dcache-for-decompression.patch new file mode 100644 index 0000000000..62bda2e830 --- /dev/null +++ b/target/linux/bcm53xx/patches-4.3/300-ARM-BCM5301X-Disable-MMU-and-Dcache-for-decompression.patch @@ -0,0 +1,86 @@ +From: Florian Fainelli +Subject: [PATCH] ARM: BCM5301x: Disable MMU and Dcache during decompression +Date: Tue, 14 Jul 2015 16:12:08 -0700 + +Use the existing __armv7_mmu_cache_flush() to perform the cache flush +since this does what we are after. + +Signed-off-by: Florian Fainelli +--- + arch/arm/boot/compressed/Makefile | 4 +++ + arch/arm/boot/compressed/head-bcm_5301x-mpcore.S | 37 ++++++++++++++++++++++++ + arch/arm/boot/compressed/head.S | 2 ++ + 3 files changed, 43 insertions(+) + create mode 100644 arch/arm/boot/compressed/head-bcm_5301x-mpcore.S + +--- a/arch/arm/boot/compressed/Makefile ++++ b/arch/arm/boot/compressed/Makefile +@@ -31,6 +31,10 @@ ifeq ($(CONFIG_ARCH_ACORN),y) + OBJS += ll_char_wr.o font.o + endif + ++ifeq ($(CONFIG_ARCH_BCM_5301X),y) ++OBJS += head-bcm_5301x-mpcore.o ++endif ++ + ifeq ($(CONFIG_ARCH_SA1100),y) + OBJS += head-sa1100.o + endif +--- /dev/null ++++ b/arch/arm/boot/compressed/head-bcm_5301x-mpcore.S +@@ -0,0 +1,37 @@ ++/* ++ * ++ * Platform specific tweaks. This is merged into head.S by the linker. ++ * ++ */ ++ ++#include ++#include ++#include ++ ++ .section ".start", "ax" ++ ++/* ++ * This code section is spliced into the head code by the linker ++ */ ++ ++__plat_uncompress_start: ++ ++ @ Preserve r8/r7 i.e. kernel entry values ++ mov r12, r8 ++ ++ @ Clear MMU enable and Dcache enable bits ++ mrc p15, 0, r0, c1, c0, 0 @ Read SCTLR ++ bic r0, #CR_C|CR_M ++ mcr p15, 0, r0, c1, c0, 0 @ Write SCTLR ++ nop ++ ++ @ Call the cache invalidation routine ++ bl __armv7_mmu_cache_flush_fn ++ nop ++ mov r0,#0 ++ ldr r3, =0x19022000 @ L2 cache controller, control reg ++ str r0, [r3, #0x100] @ Disable L2 cache ++ nop ++ ++ @ Restore ++ mov r8, r12 +--- a/arch/arm/boot/compressed/head.S ++++ b/arch/arm/boot/compressed/head.S +@@ -1152,6 +1152,7 @@ __armv7_mmu_cache_flush: + hierarchical: + mcr p15, 0, r10, c7, c10, 5 @ DMB + stmfd sp!, {r0-r7, r9-r11} ++ENTRY(__armv7_mmu_cache_flush_fn) + mrc p15, 1, r0, c0, c0, 1 @ read clidr + ands r3, r0, #0x7000000 @ extract loc from clidr + mov r3, r3, lsr #23 @ left align loc bit field +@@ -1201,6 +1202,7 @@ iflush: + mcr p15, 0, r10, c7, c10, 4 @ DSB + mcr p15, 0, r10, c7, c5, 4 @ ISB + mov pc, lr ++ENDPROC(__armv7_mmu_cache_flush_fn) + + __armv5tej_mmu_cache_flush: + tst r4, #1 diff --git a/target/linux/bcm53xx/patches-4.3/301-ARM-BCM5301X-Add-SPROM.patch b/target/linux/bcm53xx/patches-4.3/301-ARM-BCM5301X-Add-SPROM.patch new file mode 100644 index 0000000000..9ca76b3d4c --- /dev/null +++ b/target/linux/bcm53xx/patches-4.3/301-ARM-BCM5301X-Add-SPROM.patch @@ -0,0 +1,26 @@ +From d404e0b22356078a51719fa911f6e09cb1a72d80 Mon Sep 17 00:00:00 2001 +From: =?UTF-8?q?Rafa=C5=82=20Mi=C5=82ecki?= +Date: Sun, 7 Jun 2015 16:18:18 +0200 +Subject: [PATCH] ARM: BCM5301X: Add SPROM +MIME-Version: 1.0 +Content-Type: text/plain; charset=UTF-8 +Content-Transfer-Encoding: 8bit + +Signed-off-by: Rafał Miłecki +--- + arch/arm/boot/dts/bcm5301x.dtsi | 4 ++++ + 1 file changed, 4 insertions(+) + +--- a/arch/arm/boot/dts/bcm5301x.dtsi ++++ b/arch/arm/boot/dts/bcm5301x.dtsi +@@ -105,6 +105,10 @@ + }; + }; + ++ sprom0: sprom@0 { ++ compatible = "brcm,bcm47xx-sprom"; ++ }; ++ + axi@18000000 { + compatible = "brcm,bus-axi"; + reg = <0x18000000 0x1000>; diff --git a/target/linux/bcm53xx/patches-4.3/305-ARM-BCM5301X-Add-DT-for-Linksys-EA6300-V1.patch b/target/linux/bcm53xx/patches-4.3/305-ARM-BCM5301X-Add-DT-for-Linksys-EA6300-V1.patch new file mode 100644 index 0000000000..82ac24e3fd --- /dev/null +++ b/target/linux/bcm53xx/patches-4.3/305-ARM-BCM5301X-Add-DT-for-Linksys-EA6300-V1.patch @@ -0,0 +1,69 @@ +From: =?UTF-8?q?Rafa=C5=82=20Mi=C5=82ecki?= +Subject: [PATCH] ARM: BCM5301X: Add DT for Linksys EA6300 V1 +MIME-Version: 1.0 +Content-Type: text/plain; charset=UTF-8 +Content-Transfer-Encoding: 8bit + +Signed-off-by: Rafał Miłecki +--- +--- a/arch/arm/boot/dts/Makefile ++++ b/arch/arm/boot/dts/Makefile +@@ -63,6 +63,7 @@ dtb-$(CONFIG_ARCH_BCM_5301X) += \ + bcm4708-asus-rt-ac56u.dtb \ + bcm4708-asus-rt-ac68u.dtb \ + bcm4708-buffalo-wzr-1750dhp.dtb \ ++ bcm4708-linksys-ea6300-v1.dtb \ + bcm4708-luxul-xwc-1000.dtb \ + bcm4708-netgear-r6250.dtb \ + bcm4708-netgear-r6300-v2.dtb \ +--- /dev/null ++++ b/arch/arm/boot/dts/bcm4708-linksys-ea6300-v1.dts +@@ -0,0 +1,48 @@ ++/* ++ * Broadcom BCM470X / BCM5301X ARM platform code. ++ * DTS for Linksys EA6300 V1 ++ * ++ * Copyright (C) 2015 Rafał Miłecki ++ * ++ * Licensed under the GNU/GPL. See COPYING for details. ++ */ ++ ++/dts-v1/; ++ ++#include "bcm4708.dtsi" ++#include "bcm5301x-nand-cs0-bch8.dtsi" ++ ++/ { ++ compatible = "linksys,ea6300v1", "brcm,bcm4708"; ++ model = "Linksys EA6300 V1"; ++ ++ chosen { ++ bootargs = "console=ttyS0,115200"; ++ }; ++ ++ memory { ++ reg = <0x00000000 0x08000000>; ++ }; ++ ++ gpio-keys { ++ compatible = "gpio-keys"; ++ #address-cells = <1>; ++ #size-cells = <0>; ++ ++ wps { ++ label = "WPS"; ++ linux,code = ; ++ gpios = <&chipcommon 7 GPIO_ACTIVE_LOW>; ++ }; ++ ++ restart { ++ label = "Reset"; ++ linux,code = ; ++ gpios = <&chipcommon 11 GPIO_ACTIVE_LOW>; ++ }; ++ }; ++}; ++ ++&uart0 { ++ status = "okay"; ++}; diff --git a/target/linux/bcm53xx/patches-4.3/320-ARM-BCM5301X-Add-Buffalo-WXR-1900DHP-clock-and-USB-p.patch b/target/linux/bcm53xx/patches-4.3/320-ARM-BCM5301X-Add-Buffalo-WXR-1900DHP-clock-and-USB-p.patch new file mode 100644 index 0000000000..802188db17 --- /dev/null +++ b/target/linux/bcm53xx/patches-4.3/320-ARM-BCM5301X-Add-Buffalo-WXR-1900DHP-clock-and-USB-p.patch @@ -0,0 +1,41 @@ +From 504dba5b073a9009ae1e3f2fc53ea9c3aa10c38a Mon Sep 17 00:00:00 2001 +From: Felix Fietkau +Date: Wed, 13 May 2015 20:56:38 +0200 +Subject: [PATCH] ARM: BCM5301X: Add Buffalo WXR-1900DHP clock and USB power + control +MIME-Version: 1.0 +Content-Type: text/plain; charset=UTF-8 +Content-Transfer-Encoding: 8bit + +Signed-off-by: Felix Fietkau +Signed-off-by: Rafał Miłecki +--- + arch/arm/boot/dts/bcm4709-buffalo-wxr-1900dhp.dts | 17 +++++++++++++++++ + 1 file changed, 17 insertions(+) + +--- a/arch/arm/boot/dts/bcm4709-buffalo-wxr-1900dhp.dts ++++ b/arch/arm/boot/dts/bcm4709-buffalo-wxr-1900dhp.dts +@@ -24,6 +24,23 @@ + reg = <0x00000000 0x08000000>; + }; + ++ clocks { ++ clk_periph: periph { ++ clock-frequency = <500000000>; ++ }; ++ }; ++ ++ axi@18000000 { ++ usb2@21000 { ++ reg = <0x00021000 0x1000>; ++ ++ #address-cells = <1>; ++ #size-cells = <1>; ++ ++ vcc-gpio = <&chipcommon 13 GPIO_ACTIVE_HIGH>; ++ }; ++ }; ++ + leds { + compatible = "gpio-leds"; + diff --git a/target/linux/bcm53xx/patches-4.3/321-ARM-BCM5301X-Set-vcc-gpio-for-USB-controllers.patch b/target/linux/bcm53xx/patches-4.3/321-ARM-BCM5301X-Set-vcc-gpio-for-USB-controllers.patch new file mode 100644 index 0000000000..871598f2e0 --- /dev/null +++ b/target/linux/bcm53xx/patches-4.3/321-ARM-BCM5301X-Set-vcc-gpio-for-USB-controllers.patch @@ -0,0 +1,63 @@ +From f1ee1275f65e87e035260f4d09a0f0ba98c6854d Mon Sep 17 00:00:00 2001 +From: =?UTF-8?q?Rafa=C5=82=20Mi=C5=82ecki?= +Date: Sun, 21 Jun 2015 12:56:32 +0200 +Subject: [PATCH] ARM: BCM5301X: Set vcc-gpio for USB controllers +MIME-Version: 1.0 +Content-Type: text/plain; charset=UTF-8 +Content-Transfer-Encoding: 8bit + +Signed-off-by: Rafał Miłecki +--- + arch/arm/boot/dts/bcm4708-buffalo-wzr-1750dhp.dts | 20 ++++++++++++++++++++ + arch/arm/boot/dts/bcm4708-netgear-r6250.dts | 11 +++++++++++ + 2 files changed, 31 insertions(+) + +--- a/arch/arm/boot/dts/bcm4708-buffalo-wzr-1750dhp.dts ++++ b/arch/arm/boot/dts/bcm4708-buffalo-wzr-1750dhp.dts +@@ -24,6 +24,26 @@ + reg = <0x00000000 0x08000000>; + }; + ++ axi@18000000 { ++ usb2@21000 { ++ reg = <0x00021000 0x1000>; ++ ++ #address-cells = <1>; ++ #size-cells = <1>; ++ ++ vcc-gpio = <&chipcommon 9 GPIO_ACTIVE_HIGH>; ++ }; ++ ++ usb3@23000 { ++ reg = <0x00023000 0x1000>; ++ ++ #address-cells = <1>; ++ #size-cells = <1>; ++ ++ vcc-gpio = <&chipcommon 10 GPIO_ACTIVE_LOW>; ++ }; ++ }; ++ + spi { + compatible = "spi-gpio"; + num-chipselects = <1>; +--- a/arch/arm/boot/dts/bcm4708-netgear-r6250.dts ++++ b/arch/arm/boot/dts/bcm4708-netgear-r6250.dts +@@ -24,6 +24,17 @@ + reg = <0x00000000 0x08000000>; + }; + ++ axi@18000000 { ++ usb3@23000 { ++ reg = <0x00023000 0x1000>; ++ ++ #address-cells = <1>; ++ #size-cells = <1>; ++ ++ vcc-gpio = <&chipcommon 0 GPIO_ACTIVE_HIGH>; ++ }; ++ }; ++ + leds { + compatible = "gpio-leds"; + diff --git a/target/linux/bcm53xx/patches-4.3/330-ARM-BCM5310X-Enable-earlyprintk-on-tested-devices.patch b/target/linux/bcm53xx/patches-4.3/330-ARM-BCM5310X-Enable-earlyprintk-on-tested-devices.patch new file mode 100644 index 0000000000..4e25647dbb --- /dev/null +++ b/target/linux/bcm53xx/patches-4.3/330-ARM-BCM5310X-Enable-earlyprintk-on-tested-devices.patch @@ -0,0 +1,170 @@ +From eb1075cc48d3c315c7403822c33da9588ab76492 Mon Sep 17 00:00:00 2001 +From: =?UTF-8?q?Rafa=C5=82=20Mi=C5=82ecki?= +Date: Wed, 14 Jan 2015 08:33:25 +0100 +Subject: [PATCH] ARM: BCM5310X: Enable earlyprintk on tested devices +MIME-Version: 1.0 +Content-Type: text/plain; charset=UTF-8 +Content-Transfer-Encoding: 8bit + +Signed-off-by: Rafał Miłecki +--- + arch/arm/boot/dts/bcm4708-buffalo-wzr-1750dhp.dts | 2 +- + arch/arm/boot/dts/bcm4708-netgear-r6250.dts | 2 +- + arch/arm/boot/dts/bcm47081-asus-rt-n18u.dts | 2 +- + arch/arm/boot/dts/bcm47081-buffalo-wzr-600dhp2.dts | 2 +- + 4 files changed, 4 insertions(+), 4 deletions(-) + +--- a/arch/arm/boot/dts/bcm4708-buffalo-wzr-1750dhp.dts ++++ b/arch/arm/boot/dts/bcm4708-buffalo-wzr-1750dhp.dts +@@ -17,7 +17,7 @@ + model = "Buffalo WZR-1750DHP (BCM4708)"; + + chosen { +- bootargs = "console=ttyS0,115200"; ++ bootargs = "console=ttyS0,115200 earlyprintk"; + }; + + memory { +--- a/arch/arm/boot/dts/bcm4708-netgear-r6250.dts ++++ b/arch/arm/boot/dts/bcm4708-netgear-r6250.dts +@@ -17,7 +17,7 @@ + model = "Netgear R6250 V1 (BCM4708)"; + + chosen { +- bootargs = "console=ttyS0,115200"; ++ bootargs = "console=ttyS0,115200 earlyprintk"; + }; + + memory { +--- a/arch/arm/boot/dts/bcm47081-asus-rt-n18u.dts ++++ b/arch/arm/boot/dts/bcm47081-asus-rt-n18u.dts +@@ -17,7 +17,7 @@ + model = "Asus RT-N18U (BCM47081)"; + + chosen { +- bootargs = "console=ttyS0,115200"; ++ bootargs = "console=ttyS0,115200 earlyprintk"; + }; + + memory { +--- a/arch/arm/boot/dts/bcm47081-buffalo-wzr-600dhp2.dts ++++ b/arch/arm/boot/dts/bcm47081-buffalo-wzr-600dhp2.dts +@@ -17,7 +17,7 @@ + model = "Buffalo WZR-600DHP2 (BCM47081)"; + + chosen { +- bootargs = "console=ttyS0,115200"; ++ bootargs = "console=ttyS0,115200 earlyprintk"; + }; + + memory { +--- a/arch/arm/boot/dts/bcm47081-buffalo-wzr-900dhp.dts ++++ b/arch/arm/boot/dts/bcm47081-buffalo-wzr-900dhp.dts +@@ -17,7 +17,7 @@ + model = "Buffalo WZR-900DHP (BCM47081)"; + + chosen { +- bootargs = "console=ttyS0,115200"; ++ bootargs = "console=ttyS0,115200 earlyprintk"; + }; + + memory { +--- a/arch/arm/boot/dts/bcm4709-netgear-r8000.dts ++++ b/arch/arm/boot/dts/bcm4709-netgear-r8000.dts +@@ -17,7 +17,7 @@ + model = "Netgear R8000 (BCM4709)"; + + chosen { +- bootargs = "console=ttyS0,115200"; ++ bootargs = "console=ttyS0,115200 earlyprintk"; + }; + + memory { +--- a/arch/arm/boot/dts/bcm4708-asus-rt-ac56u.dts ++++ b/arch/arm/boot/dts/bcm4708-asus-rt-ac56u.dts +@@ -17,7 +17,7 @@ + model = "Asus RT-AC56U (BCM4708)"; + + chosen { +- bootargs = "console=ttyS0,115200"; ++ bootargs = "console=ttyS0,115200 earlyprintk"; + }; + + memory { +--- a/arch/arm/boot/dts/bcm4708-asus-rt-ac68u.dts ++++ b/arch/arm/boot/dts/bcm4708-asus-rt-ac68u.dts +@@ -17,7 +17,7 @@ + model = "Asus RT-AC68U (BCM4708)"; + + chosen { +- bootargs = "console=ttyS0,115200"; ++ bootargs = "console=ttyS0,115200 earlyprintk"; + }; + + memory { +--- a/arch/arm/boot/dts/bcm4708-luxul-xwc-1000.dts ++++ b/arch/arm/boot/dts/bcm4708-luxul-xwc-1000.dts +@@ -17,7 +17,7 @@ + model = "Luxul XWC-1000 (BCM4708)"; + + chosen { +- bootargs = "console=ttyS0,115200"; ++ bootargs = "console=ttyS0,115200 earlyprintk"; + }; + + memory { +--- a/arch/arm/boot/dts/bcm4709-buffalo-wxr-1900dhp.dts ++++ b/arch/arm/boot/dts/bcm4709-buffalo-wxr-1900dhp.dts +@@ -17,7 +17,7 @@ + model = "Buffalo WXR-1900DHP"; + + chosen { +- bootargs = "console=ttyS0,115200"; ++ bootargs = "console=ttyS0,115200 earlyprintk"; + }; + + memory { +--- a/arch/arm/boot/dts/bcm4708-smartrg-sr400ac.dts ++++ b/arch/arm/boot/dts/bcm4708-smartrg-sr400ac.dts +@@ -17,7 +17,7 @@ + model = "SmartRG SR400ac"; + + chosen { +- bootargs = "console=ttyS0,115200"; ++ bootargs = "console=ttyS0,115200 earlyprintk"; + }; + + memory { +--- a/arch/arm/boot/dts/bcm4709-asus-rt-ac87u.dts ++++ b/arch/arm/boot/dts/bcm4709-asus-rt-ac87u.dts +@@ -17,7 +17,7 @@ + model = "Asus RT-AC87U"; + + chosen { +- bootargs = "console=ttyS0,115200"; ++ bootargs = "console=ttyS0,115200 earlyprintk"; + }; + + memory { +--- a/arch/arm/boot/dts/bcm4709-netgear-r7000.dts ++++ b/arch/arm/boot/dts/bcm4709-netgear-r7000.dts +@@ -17,7 +17,7 @@ + model = "Netgear R7000"; + + chosen { +- bootargs = "console=ttyS0,115200"; ++ bootargs = "console=ttyS0,115200 earlyprintk"; + }; + + memory { +--- a/arch/arm/boot/dts/bcm4708-linksys-ea6300-v1.dts ++++ b/arch/arm/boot/dts/bcm4708-linksys-ea6300-v1.dts +@@ -17,7 +17,7 @@ + model = "Linksys EA6300 V1"; + + chosen { +- bootargs = "console=ttyS0,115200"; ++ bootargs = "console=ttyS0,115200 earlyprintk"; + }; + + memory { diff --git a/target/linux/bcm53xx/patches-4.3/331-ARM-BCM5301X-Specify-RAM-on-devices-by-including-HIG.patch b/target/linux/bcm53xx/patches-4.3/331-ARM-BCM5301X-Specify-RAM-on-devices-by-including-HIG.patch new file mode 100644 index 0000000000..750d83368c --- /dev/null +++ b/target/linux/bcm53xx/patches-4.3/331-ARM-BCM5301X-Specify-RAM-on-devices-by-including-HIG.patch @@ -0,0 +1,173 @@ +From 36b2fbb3badf0e32b371e1f7579a95d4fe25c0e1 Mon Sep 17 00:00:00 2001 +From: =?UTF-8?q?Rafa=C5=82=20Mi=C5=82ecki?= +Date: Wed, 14 Jan 2015 09:13:58 +0100 +Subject: [PATCH] ARM: BCM5301X: Specify RAM on devices by including HIGHMEM +MIME-Version: 1.0 +Content-Type: text/plain; charset=UTF-8 +Content-Transfer-Encoding: 8bit + +Signed-off-by: Rafał Miłecki +--- + arch/arm/boot/dts/bcm4708-buffalo-wzr-1750dhp.dts | 3 ++- + arch/arm/boot/dts/bcm4708-netgear-r6250.dts | 3 ++- + arch/arm/boot/dts/bcm4708-netgear-r6300-v2.dts | 3 ++- + arch/arm/boot/dts/bcm47081-asus-rt-n18u.dts | 3 ++- + arch/arm/boot/dts/bcm47081-buffalo-wzr-600dhp2.dts | 3 ++- + 5 files changed, 10 insertions(+), 5 deletions(-) + +--- a/arch/arm/boot/dts/bcm4708-buffalo-wzr-1750dhp.dts ++++ b/arch/arm/boot/dts/bcm4708-buffalo-wzr-1750dhp.dts +@@ -21,7 +21,8 @@ + }; + + memory { +- reg = <0x00000000 0x08000000>; ++ reg = <0x00000000 0x08000000 ++ 0x88000000 0x18000000>; + }; + + axi@18000000 { +--- a/arch/arm/boot/dts/bcm4708-netgear-r6250.dts ++++ b/arch/arm/boot/dts/bcm4708-netgear-r6250.dts +@@ -21,7 +21,8 @@ + }; + + memory { +- reg = <0x00000000 0x08000000>; ++ reg = <0x00000000 0x08000000 ++ 0x88000000 0x08000000>; + }; + + axi@18000000 { +--- a/arch/arm/boot/dts/bcm4708-netgear-r6300-v2.dts ++++ b/arch/arm/boot/dts/bcm4708-netgear-r6300-v2.dts +@@ -21,7 +21,8 @@ + }; + + memory { +- reg = <0x00000000 0x08000000>; ++ reg = <0x00000000 0x08000000 ++ 0x88000000 0x08000000>; + }; + + leds { +--- a/arch/arm/boot/dts/bcm47081-asus-rt-n18u.dts ++++ b/arch/arm/boot/dts/bcm47081-asus-rt-n18u.dts +@@ -21,7 +21,8 @@ + }; + + memory { +- reg = <0x00000000 0x08000000>; ++ reg = <0x00000000 0x08000000 ++ 0x88000000 0x08000000>; + }; + + leds { +--- a/arch/arm/boot/dts/bcm47081-buffalo-wzr-600dhp2.dts ++++ b/arch/arm/boot/dts/bcm47081-buffalo-wzr-600dhp2.dts +@@ -21,7 +21,8 @@ + }; + + memory { +- reg = <0x00000000 0x08000000>; ++ reg = <0x00000000 0x08000000 ++ 0x88000000 0x08000000>; + }; + + spi { +--- a/arch/arm/boot/dts/bcm47081-buffalo-wzr-900dhp.dts ++++ b/arch/arm/boot/dts/bcm47081-buffalo-wzr-900dhp.dts +@@ -21,7 +21,8 @@ + }; + + memory { +- reg = <0x00000000 0x08000000>; ++ reg = <0x00000000 0x08000000 ++ 0x88000000 0x08000000>; + }; + + gpio-keys { +--- a/arch/arm/boot/dts/bcm4709-netgear-r8000.dts ++++ b/arch/arm/boot/dts/bcm4709-netgear-r8000.dts +@@ -21,7 +21,8 @@ + }; + + memory { +- reg = <0x00000000 0x08000000>; ++ reg = <0x00000000 0x08000000 ++ 0x88000000 0x08000000>; + }; + + leds { +--- a/arch/arm/boot/dts/bcm4708-asus-rt-ac56u.dts ++++ b/arch/arm/boot/dts/bcm4708-asus-rt-ac56u.dts +@@ -21,7 +21,8 @@ + }; + + memory { +- reg = <0x00000000 0x08000000>; ++ reg = <0x00000000 0x08000000 ++ 0x88000000 0x08000000>; + }; + + leds { +--- a/arch/arm/boot/dts/bcm4708-asus-rt-ac68u.dts ++++ b/arch/arm/boot/dts/bcm4708-asus-rt-ac68u.dts +@@ -21,7 +21,8 @@ + }; + + memory { +- reg = <0x00000000 0x08000000>; ++ reg = <0x00000000 0x08000000 ++ 0x88000000 0x08000000>; + }; + + leds { +--- a/arch/arm/boot/dts/bcm4709-buffalo-wxr-1900dhp.dts ++++ b/arch/arm/boot/dts/bcm4709-buffalo-wxr-1900dhp.dts +@@ -21,7 +21,8 @@ + }; + + memory { +- reg = <0x00000000 0x08000000>; ++ reg = <0x00000000 0x08000000 ++ 0x88000000 0x18000000>; + }; + + clocks { +--- a/arch/arm/boot/dts/bcm4708-smartrg-sr400ac.dts ++++ b/arch/arm/boot/dts/bcm4708-smartrg-sr400ac.dts +@@ -21,7 +21,8 @@ + }; + + memory { +- reg = <0x00000000 0x08000000>; ++ reg = <0x00000000 0x08000000 ++ 0x88000000 0x08000000>; + }; + + leds { +--- a/arch/arm/boot/dts/bcm4709-asus-rt-ac87u.dts ++++ b/arch/arm/boot/dts/bcm4709-asus-rt-ac87u.dts +@@ -21,7 +21,8 @@ + }; + + memory { +- reg = <0x00000000 0x08000000>; ++ reg = <0x00000000 0x08000000 ++ 0x88000000 0x08000000>; + }; + + leds { +--- a/arch/arm/boot/dts/bcm4709-netgear-r7000.dts ++++ b/arch/arm/boot/dts/bcm4709-netgear-r7000.dts +@@ -21,7 +21,8 @@ + }; + + memory { +- reg = <0x00000000 0x08000000>; ++ reg = <0x00000000 0x08000000 ++ 0x88000000 0x08000000>; + }; + + leds { diff --git a/target/linux/bcm53xx/patches-4.3/332-ARM-BCM5301X-Add-power-button-for-Buffalo-WZR-1750DHP.patch b/target/linux/bcm53xx/patches-4.3/332-ARM-BCM5301X-Add-power-button-for-Buffalo-WZR-1750DHP.patch new file mode 100644 index 0000000000..f9ca7eb7c1 --- /dev/null +++ b/target/linux/bcm53xx/patches-4.3/332-ARM-BCM5301X-Add-power-button-for-Buffalo-WZR-1750DHP.patch @@ -0,0 +1,20 @@ +From: Felix Fietkau +Subject: [PATCH] ARM: BCM5301X: Add power button for Buffalo WZR-1750DHP + +Signed-off-by: Felix Fietkau +--- +--- a/arch/arm/boot/dts/bcm4708-buffalo-wzr-1750dhp.dts ++++ b/arch/arm/boot/dts/bcm4708-buffalo-wzr-1750dhp.dts +@@ -123,6 +123,12 @@ + #address-cells = <1>; + #size-cells = <0>; + ++ power { ++ label = "Power"; ++ linux,code = ; ++ gpios = <&chipcommon 1 GPIO_ACTIVE_LOW>; ++ }; ++ + restart { + label = "Reset"; + linux,code = ; diff --git a/target/linux/bcm53xx/patches-4.3/351-ARM-BCM5301X-Enable-ChipCommon-UART-on-untested-devi.patch b/target/linux/bcm53xx/patches-4.3/351-ARM-BCM5301X-Enable-ChipCommon-UART-on-untested-devi.patch new file mode 100644 index 0000000000..dfeb70e179 --- /dev/null +++ b/target/linux/bcm53xx/patches-4.3/351-ARM-BCM5301X-Enable-ChipCommon-UART-on-untested-devi.patch @@ -0,0 +1,111 @@ +From b49d7bb4825654f81bcee8e219028712811515a5 Mon Sep 17 00:00:00 2001 +From: =?UTF-8?q?Rafa=C5=82=20Mi=C5=82ecki?= +Date: Mon, 29 Jun 2015 08:11:36 +0200 +Subject: [PATCH] ARM: BCM5301X: Enable ChipCommon UART on untested devices +MIME-Version: 1.0 +Content-Type: text/plain; charset=UTF-8 +Content-Transfer-Encoding: 8bit + +Signed-off-by: Rafał Miłecki +--- + arch/arm/boot/dts/bcm4708-asus-rt-ac56u.dts | 4 ++++ + arch/arm/boot/dts/bcm4708-asus-rt-ac68u.dts | 4 ++++ + arch/arm/boot/dts/bcm4708-netgear-r6300-v2.dts | 4 ++++ + arch/arm/boot/dts/bcm47081-asus-rt-n18u.dts | 4 ++++ + arch/arm/boot/dts/bcm47081-buffalo-wzr-900dhp.dts | 4 ++++ + arch/arm/boot/dts/bcm4709-asus-rt-ac87u.dts | 5 +++++ + arch/arm/boot/dts/bcm4709-buffalo-wxr-1900dhp.dts | 5 +++++ + arch/arm/boot/dts/bcm4709-netgear-r8000.dts | 5 +++++ + 8 files changed, 35 insertions(+) + +--- a/arch/arm/boot/dts/bcm4708-asus-rt-ac56u.dts ++++ b/arch/arm/boot/dts/bcm4708-asus-rt-ac56u.dts +@@ -96,3 +96,7 @@ + }; + }; + }; ++ ++&uart0 { ++ status = "okay"; ++}; +--- a/arch/arm/boot/dts/bcm4708-asus-rt-ac68u.dts ++++ b/arch/arm/boot/dts/bcm4708-asus-rt-ac68u.dts +@@ -83,3 +83,7 @@ + }; + }; + }; ++ ++&uart0 { ++ status = "okay"; ++}; +--- a/arch/arm/boot/dts/bcm4708-netgear-r6300-v2.dts ++++ b/arch/arm/boot/dts/bcm4708-netgear-r6300-v2.dts +@@ -83,3 +83,7 @@ + }; + }; + }; ++ ++&uart0 { ++ status = "okay"; ++}; +--- a/arch/arm/boot/dts/bcm47081-asus-rt-n18u.dts ++++ b/arch/arm/boot/dts/bcm47081-asus-rt-n18u.dts +@@ -77,3 +77,7 @@ + }; + }; + }; ++ ++&uart0 { ++ status = "okay"; ++}; +--- a/arch/arm/boot/dts/bcm47081-buffalo-wzr-900dhp.dts ++++ b/arch/arm/boot/dts/bcm47081-buffalo-wzr-900dhp.dts +@@ -37,3 +37,7 @@ + }; + }; + }; ++ ++&uart0 { ++ status = "okay"; ++}; +--- a/arch/arm/boot/dts/bcm4709-asus-rt-ac87u.dts ++++ b/arch/arm/boot/dts/bcm4709-asus-rt-ac87u.dts +@@ -65,3 +65,8 @@ + }; + }; + }; ++ ++&uart0 { ++ status = "okay"; ++ clock-frequency = <125000000>; ++}; +--- a/arch/arm/boot/dts/bcm4709-buffalo-wxr-1900dhp.dts ++++ b/arch/arm/boot/dts/bcm4709-buffalo-wxr-1900dhp.dts +@@ -144,3 +144,8 @@ + }; + }; + }; ++ ++&uart0 { ++ status = "okay"; ++ clock-frequency = <125000000>; ++}; +--- a/arch/arm/boot/dts/bcm4709-netgear-r8000.dts ++++ b/arch/arm/boot/dts/bcm4709-netgear-r8000.dts +@@ -77,3 +77,8 @@ + }; + }; + }; ++ ++&uart0 { ++ status = "okay"; ++ clock-frequency = <125000000>; ++}; +--- a/arch/arm/boot/dts/bcm4709-netgear-r7000.dts ++++ b/arch/arm/boot/dts/bcm4709-netgear-r7000.dts +@@ -104,4 +104,5 @@ + + &uart0 { + status = "okay"; ++ clock-frequency = <125000000>; + }; diff --git a/target/linux/bcm53xx/patches-4.3/400-mtd-bcm47xxpart-scan-whole-flash-on-ARCH_BCM_5301X.patch b/target/linux/bcm53xx/patches-4.3/400-mtd-bcm47xxpart-scan-whole-flash-on-ARCH_BCM_5301X.patch new file mode 100644 index 0000000000..ccdb28b54d --- /dev/null +++ b/target/linux/bcm53xx/patches-4.3/400-mtd-bcm47xxpart-scan-whole-flash-on-ARCH_BCM_5301X.patch @@ -0,0 +1,31 @@ +From d658c21d6697293a928434fd6ac19264b5a8948d Mon Sep 17 00:00:00 2001 +From: =?UTF-8?q?Rafa=C5=82=20Mi=C5=82ecki?= +Date: Fri, 30 Jan 2015 08:25:54 +0100 +Subject: [PATCH] mtd: bcm47xxpart: scan whole flash on ARCH_BCM_5301X +MIME-Version: 1.0 +Content-Type: text/plain; charset=UTF-8 +Content-Transfer-Encoding: 8bit + +Signed-off-by: Rafał Miłecki +--- + drivers/mtd/bcm47xxpart.c | 6 ++++++ + 1 file changed, 6 insertions(+) + +--- a/drivers/mtd/bcm47xxpart.c ++++ b/drivers/mtd/bcm47xxpart.c +@@ -120,9 +120,15 @@ static int bcm47xxpart_parse(struct mtd_ + /* Parse block by block looking for magics */ + for (offset = 0; offset <= master->size - blocksize; + offset += blocksize) { ++#ifndef CONFIG_ARCH_BCM_5301X ++ /* ++ * ARM routers may have partitions in higher memory. E.g. ++ * Netgear R8000 has board_data at 0x2600000. ++ */ + /* Nothing more in higher memory */ + if (offset >= 0x2000000) + break; ++#endif + + if (curr_part >= BCM47XXPART_MAX_PARTS) { + pr_warn("Reached maximum number of partitions, scanning stopped!\n"); diff --git a/target/linux/bcm53xx/patches-4.3/404-mtd-bcm53xxspiflash-new-driver-for-SPI-flahes-on-Bro.patch b/target/linux/bcm53xx/patches-4.3/404-mtd-bcm53xxspiflash-new-driver-for-SPI-flahes-on-Bro.patch new file mode 100644 index 0000000000..79af78507c --- /dev/null +++ b/target/linux/bcm53xx/patches-4.3/404-mtd-bcm53xxspiflash-new-driver-for-SPI-flahes-on-Bro.patch @@ -0,0 +1,20 @@ +--- a/drivers/mtd/spi-nor/Kconfig ++++ b/drivers/mtd/spi-nor/Kconfig +@@ -40,4 +40,10 @@ config SPI_NXP_SPIFI + Flash. Enable this option if you have a device with a SPIFI + controller and want to access the Flash as a mtd device. + ++config MTD_SPI_BCM53XXSPIFLASH ++ tristate "SPI-NOR flashes connected to the Broadcom ARM SoC" ++ depends on MTD_SPI_NOR ++ help ++ SPI driver for flashes used on Broadcom ARM SoCs. ++ + endif # MTD_SPI_NOR +--- a/drivers/mtd/spi-nor/Makefile ++++ b/drivers/mtd/spi-nor/Makefile +@@ -1,3 +1,4 @@ + obj-$(CONFIG_MTD_SPI_NOR) += spi-nor.o + obj-$(CONFIG_SPI_FSL_QUADSPI) += fsl-quadspi.o ++obj-$(CONFIG_MTD_SPI_BCM53XXSPIFLASH) += bcm53xxspiflash.o + obj-$(CONFIG_SPI_NXP_SPIFI) += nxp-spifi.o diff --git a/target/linux/bcm53xx/patches-4.3/500-UBI-Detect-EOF-mark-and-erase-all-remaining-blocks.patch b/target/linux/bcm53xx/patches-4.3/500-UBI-Detect-EOF-mark-and-erase-all-remaining-blocks.patch new file mode 100644 index 0000000000..a3d0f75b48 --- /dev/null +++ b/target/linux/bcm53xx/patches-4.3/500-UBI-Detect-EOF-mark-and-erase-all-remaining-blocks.patch @@ -0,0 +1,59 @@ +From 2a2af518266a29323cf30c3f9ba9ef2ceb1dd84b Mon Sep 17 00:00:00 2001 +From: =?UTF-8?q?Rafa=C5=82=20Mi=C5=82ecki?= +Date: Thu, 16 Oct 2014 20:52:16 +0200 +Subject: [PATCH] UBI: Detect EOF mark and erase all remaining blocks +MIME-Version: 1.0 +Content-Type: text/plain; charset=UTF-8 +Content-Transfer-Encoding: 8bit + +Signed-off-by: Rafał Miłecki +--- + drivers/mtd/ubi/attach.c | 5 +++++ + drivers/mtd/ubi/io.c | 4 ++++ + drivers/mtd/ubi/ubi.h | 1 + + 3 files changed, 10 insertions(+) + +--- a/drivers/mtd/ubi/attach.c ++++ b/drivers/mtd/ubi/attach.c +@@ -95,6 +95,9 @@ static int self_check_ai(struct ubi_devi + static struct ubi_ec_hdr *ech; + static struct ubi_vid_hdr *vidh; + ++/* Set on finding block with 0xdeadc0de, indicates erasing all blocks behind */ ++bool erase_all_next; ++ + /** + * add_to_list - add physical eraseblock to a list. + * @ai: attaching information +@@ -1427,6 +1430,8 @@ int ubi_attach(struct ubi_device *ubi, i + if (!ai) + return -ENOMEM; + ++ erase_all_next = false; ++ + #ifdef CONFIG_MTD_UBI_FASTMAP + /* On small flash devices we disable fastmap in any case. */ + if ((int)mtd_div_by_eb(ubi->mtd->size, ubi->mtd) <= UBI_FM_MAX_START) { +--- a/drivers/mtd/ubi/io.c ++++ b/drivers/mtd/ubi/io.c +@@ -755,6 +755,10 @@ int ubi_io_read_ec_hdr(struct ubi_device + } + + magic = be32_to_cpu(ec_hdr->magic); ++ if (magic == 0xdeadc0de) ++ erase_all_next = true; ++ if (erase_all_next) ++ return read_err ? UBI_IO_FF_BITFLIPS : UBI_IO_FF; + if (magic != UBI_EC_HDR_MAGIC) { + if (mtd_is_eccerr(read_err)) + return UBI_IO_BAD_HDR_EBADMSG; +--- a/drivers/mtd/ubi/ubi.h ++++ b/drivers/mtd/ubi/ubi.h +@@ -781,6 +781,7 @@ extern struct mutex ubi_devices_mutex; + extern struct blocking_notifier_head ubi_notifiers; + + /* attach.c */ ++extern bool erase_all_next; + int ubi_add_to_av(struct ubi_device *ubi, struct ubi_attach_info *ai, int pnum, + int ec, const struct ubi_vid_hdr *vid_hdr, int bitflips); + struct ubi_ainf_volume *ubi_find_av(const struct ubi_attach_info *ai, diff --git a/target/linux/bcm53xx/patches-4.3/710-b53-add-hacky-CPU-port-fixes-for-devices-not-using-p.patch b/target/linux/bcm53xx/patches-4.3/710-b53-add-hacky-CPU-port-fixes-for-devices-not-using-p.patch new file mode 100644 index 0000000000..6015c4aaca --- /dev/null +++ b/target/linux/bcm53xx/patches-4.3/710-b53-add-hacky-CPU-port-fixes-for-devices-not-using-p.patch @@ -0,0 +1,35 @@ +From 4abdde3ad6bc0b3b157c4bf6ec0bf139d11d07e8 Mon Sep 17 00:00:00 2001 +From: =?UTF-8?q?Rafa=C5=82=20Mi=C5=82ecki?= +Date: Wed, 13 May 2015 14:13:28 +0200 +Subject: [PATCH] b53: add hacky CPU port fixes for devices not using port 5 +MIME-Version: 1.0 +Content-Type: text/plain; charset=UTF-8 +Content-Transfer-Encoding: 8bit + +Signed-off-by: Rafał Miłecki +--- + drivers/net/phy/b53/b53_common.c | 6 ++++++ + 1 file changed, 6 insertions(+) + +--- a/drivers/net/phy/b53/b53_common.c ++++ b/drivers/net/phy/b53/b53_common.c +@@ -25,6 +25,7 @@ + #include + #include + #include ++#include + + #include "b53_regs.h" + #include "b53_priv.h" +@@ -1313,6 +1314,11 @@ static int b53_switch_init(struct b53_de + sw_dev->cpu_port = 5; + } + ++ if (of_machine_is_compatible("asus,rt-ac87u")) ++ sw_dev->cpu_port = 7; ++ else if (of_machine_is_compatible("netgear,r8000")) ++ sw_dev->cpu_port = 8; ++ + /* cpu port is always last */ + sw_dev->ports = sw_dev->cpu_port + 1; + dev->enabled_ports |= BIT(sw_dev->cpu_port); diff --git a/target/linux/bcm53xx/patches-4.3/800-bcma-use-two-different-initcalls-if-built-in.patch b/target/linux/bcm53xx/patches-4.3/800-bcma-use-two-different-initcalls-if-built-in.patch new file mode 100644 index 0000000000..4e5793bc86 --- /dev/null +++ b/target/linux/bcm53xx/patches-4.3/800-bcma-use-two-different-initcalls-if-built-in.patch @@ -0,0 +1,65 @@ +From 666bdfc027cde41a171862dc698987a378c8b66a Mon Sep 17 00:00:00 2001 +From: =?UTF-8?q?Rafa=C5=82=20Mi=C5=82ecki?= +Date: Mon, 9 Feb 2015 18:00:42 +0100 +Subject: [PATCH RFC] bcma: use two different initcalls if built-in +MIME-Version: 1.0 +Content-Type: text/plain; charset=UTF-8 +Content-Transfer-Encoding: 8bit + +This is needed as we can't initialize bus during fs_initcall. +Initialization requires SPROM which depends on NVRAM which depends on +mtd. Since mtd, spi, nand, spi-nor use standard module_init, we have to +do the same in bcma. +Without this we'll try to initialize SPROM without having a ready SPROM +proviver registered using bcma_arch_register_fallback_sprom. + +Signed-off-by: Rafał Miłecki +--- +While this patch seems to work and I can compile bcma as built-in and +module, I'm not too proud of it. I don't really like these #if(n)def +tricks and I'm afraid bcma_modinit may be called even if +bcma_modinit_early failed. + +Do you see any better idea of solving this? +--- + drivers/bcma/main.c | 16 ++++++++++++++-- + 1 file changed, 14 insertions(+), 2 deletions(-) + +--- a/drivers/bcma/main.c ++++ b/drivers/bcma/main.c +@@ -673,13 +673,25 @@ static int bcma_device_uevent(struct dev + core->id.rev, core->id.class); + } + ++/* Bus has to be registered early, before any bcma driver */ ++static int __init bcma_modinit_early(void) ++{ ++ return bus_register(&bcma_bus_type); ++} ++#ifndef MODULE ++fs_initcall(bcma_modinit_early); ++#endif ++ ++/* Initialization has to be done later with SPI/mtd/NAND/SPROM available */ + static int __init bcma_modinit(void) + { + int err; + +- err = bus_register(&bcma_bus_type); ++#ifdef MODULE ++ err = bcma_modinit_early(); + if (err) + return err; ++#endif + + err = bcma_host_soc_register_driver(); + if (err) { +@@ -696,7 +708,7 @@ static int __init bcma_modinit(void) + + return err; + } +-fs_initcall(bcma_modinit); ++module_init(bcma_modinit); + + static void __exit bcma_modexit(void) + { diff --git a/target/linux/bcm53xx/patches-4.3/901-mtd-bcm47xxpart-workaround-for-Asus-RT-AC87U-asus-pa.patch b/target/linux/bcm53xx/patches-4.3/901-mtd-bcm47xxpart-workaround-for-Asus-RT-AC87U-asus-pa.patch new file mode 100644 index 0000000000..c1dfa92013 --- /dev/null +++ b/target/linux/bcm53xx/patches-4.3/901-mtd-bcm47xxpart-workaround-for-Asus-RT-AC87U-asus-pa.patch @@ -0,0 +1,42 @@ +From 21500872c1dba33848ddcf6bea97d58772675d36 Mon Sep 17 00:00:00 2001 +From: =?UTF-8?q?Rafa=C5=82=20Mi=C5=82ecki?= +Date: Sun, 17 May 2015 14:00:52 +0200 +Subject: [PATCH] mtd: bcm47xxpart: workaround for Asus RT-AC87U "asus" + partition +MIME-Version: 1.0 +Content-Type: text/plain; charset=UTF-8 +Content-Transfer-Encoding: 8bit + +Signed-off-by: Rafał Miłecki +--- + drivers/mtd/bcm47xxpart.c | 12 ++++++++++++ + 1 file changed, 12 insertions(+) + +--- a/drivers/mtd/bcm47xxpart.c ++++ b/drivers/mtd/bcm47xxpart.c +@@ -14,6 +14,7 @@ + #include + #include + #include ++#include + + #include + +@@ -135,6 +136,17 @@ static int bcm47xxpart_parse(struct mtd_ + break; + } + ++ /* ++ * Ugly workaround for Asus RT-AC87U and its "asus" partition. ++ * It uses JFFS2 which we don't (want to) detect. We should ++ * probably use DT to define partitions but we need a working ++ * TRX firmware splitter first. ++ */ ++ if (of_machine_is_compatible("asus,rt-ac87u") && offset == 0x7ec0000) { ++ bcm47xxpart_add_part(&parts[curr_part++], "asus", offset, MTD_WRITEABLE); ++ continue; ++ } ++ + /* Read beginning of the block */ + if (mtd_read(master, offset, BCM47XXPART_BYTES_TO_READ, + &bytes_read, (uint8_t *)buf) < 0) {