From: Borys Zhukov Date: Sun, 7 Jul 2024 22:54:07 +0000 (-0400) Subject: ramips: add support for Netgear WAX214v2 X-Git-Url: http://git.lede-project.org./?a=commitdiff_plain;h=f25cd55bd1d13d2b89fefd4b1a88198ece1f8bbf;p=openwrt%2Fstaging%2Fthess.git ramips: add support for Netgear WAX214v2 Netgear WAX214v2 is an 802.11ax (Wi-Fi 6) wireless access point. Specifications: * SoC: MediaTek MT7621AT * RAM: 512 MiB * Flash: NAND 128 MiB (ESMT PSU1GA30DT) * Wi-Fi: 2.4/5 GHz 4T4R (MediaTek MT7915E) * Ethernet: 1x 10/100/1000 Mbps LAN * Switch: MediaTek MT7530 (SoC built-in) * LEDs/Keys * Power (green, blue, amber) * LAN (green, amber) * WLAN 2.4GHz (green, blue) * WLAN 5GHz (green, blue) * Reset button * USB: None * UART: Marked J1 on board, 115200 8N1 * Power * 12 VDC, 1.5 A * IEEE 802.3at (PoE+) Load addresses (same as Netgear WAX202): * stock * 0x80010000: FIT image * 0x81001000: kernel image -> entry * OpenWrt * 0x80010000: FIT image * 0x82000000: uncompressed kernel+relocate image * 0x80001000: relocated kernel image -> entry MAC addresses as verified by OEM firmware: vendor OpenWrt address eth0 lan label ra0 phy0 label + 2 rax0 phy1 label + 3 Installation: * Flash the factory image by TFTP to the bootloader. NMRP can be used to TFTP without opening the case. Revert to stock firmware: * Flash the stock firmware to the bootloader using TFTP/NMRP. References to WAX214v2 GPL source: https://www.downloads.netgear.com/files/GPL/WAX214v2-V1.0.1.5-gpl-src.tar.gz * openwrt/target/linux/ramips/dts/mt7621-ax-nand-wax214v2.dts DTS file for this device. Signed-off-by: Borys Zhukov Link: https://github.com/openwrt/openwrt/pull/14401 Signed-off-by: Hauke Mehrtens --- diff --git a/package/boot/uboot-envtools/files/ramips b/package/boot/uboot-envtools/files/ramips index 3deb46c295..cca394a03b 100644 --- a/package/boot/uboot-envtools/files/ramips +++ b/package/boot/uboot-envtools/files/ramips @@ -146,6 +146,10 @@ xiaomi,mi-router-cr6608|\ xiaomi,mi-router-cr6609) ubootenv_add_uci_config "/dev/mtd1" "0x0" "0x10000" "0x20000" ;; +netgear,wax214v2) + ubootenv_add_uci_config "/dev/mtd1" "0x0" "0x20000" "0x20000" + ubootenv_add_uci_sys_config "/dev/mtd1" "0x20000" "0x8000" "0x20000" + ;; esac config_load ubootenv diff --git a/target/linux/ramips/dts/mt7621_netgear_wax214v2.dts b/target/linux/ramips/dts/mt7621_netgear_wax214v2.dts new file mode 100644 index 0000000000..a9597119fa --- /dev/null +++ b/target/linux/ramips/dts/mt7621_netgear_wax214v2.dts @@ -0,0 +1,228 @@ +// SPDX-License-Identifier: GPL-2.0-or-later OR MIT + +#include "mt7621.dtsi" + +#include +#include +#include + +/ { + compatible = "netgear,wax214v2", "mediatek,mt7621-soc"; + model = "Netgear WAX214v2"; + + aliases { + led-boot = &led_power_green; + led-failsafe = &led_power_amber; + led-running = &led_power_green; + led-upgrade = &led_power_blue; + }; + + chosen { + bootargs = "console=ttyS0,115200"; + }; + + keys { + compatible = "gpio-keys"; + + reset { + label = "reset"; + gpios = <&gpio 10 GPIO_ACTIVE_LOW>; + linux,code = ; + }; + }; + + leds { + compatible = "gpio-leds"; + + led_power_green: power_green { + function = LED_FUNCTION_POWER; + color = ; + gpios = <&gpio 15 GPIO_ACTIVE_LOW>; + }; + + led_power_blue: power_blue { + function = LED_FUNCTION_POWER; + color = ; + gpios = <&gpio 14 GPIO_ACTIVE_LOW>; + }; + + led_power_amber: power_amber { + function = LED_FUNCTION_POWER; + color = ; + gpios = <&gpio 13 GPIO_ACTIVE_LOW>; + }; + + wifin_green { + function = LED_FUNCTION_WLAN_2GHZ; + color = ; + gpios = <&gpio 12 GPIO_ACTIVE_LOW>; + linux,default-trigger = "phy0radio"; + }; + + wifia_green { + function = LED_FUNCTION_WLAN_5GHZ; + color = ; + gpios = <&gpio 8 GPIO_ACTIVE_LOW>; + linux,default-trigger = "phy1radio"; + }; + }; +}; + +&nand { + status = "okay"; + + partitions { + compatible = "fixed-partitions"; + #address-cells = <1>; + #size-cells = <1>; + + partition@0 { + label = "Bootloader"; + reg = <0x0 0x80000>; + read-only; + }; + + partition@80000 { + label = "Config"; + reg = <0x80000 0x80000>; + }; + + partition@100000 { + label = "Factory"; + reg = <0x100000 0x80000>; + read-only; + + nvmem-layout { + compatible = "fixed-layout"; + #address-cells = <1>; + #size-cells = <1>; + + eeprom_factory_0: eeprom@0 { + reg = <0x0 0xe00>; + }; + + precal_factory_e10: precal@e10 { + reg = <0xe10 0x19c10>; + }; + }; + }; + + partition@180000 { + label = "firmware"; + reg = <0x180000 0x2600000>; + + compatible = "fixed-partitions"; + #address-cells = <1>; + #size-cells = <1>; + + partition@0 { + label = "kernel"; + reg = <0x0 0x400000>; + }; + + partition@400000 { + label = "ubi"; + reg = <0x400000 0x2200000>; + }; + }; + + partition@2780000 { + label = "firmware_backup"; + reg = <0x2780000 0x2600000>; + read-only; + }; + + partition@4d80000 { + label = "CFG"; + reg = <0x4d80000 0x800000>; + read-only; + }; + + partition@5580000 { + label = "RAE"; + reg = <0x5580000 0x400000>; + read-only; + }; + + partition@5980000 { + label = "POT"; + reg = <0x5980000 0x100000>; + read-only; + }; + + partition@5a80000 { + label = "Language"; + reg = <0x5a80000 0x400000>; + read-only; + }; + + partition@5e80000 { + label = "Traffic"; + reg = <0x5e80000 0x200000>; + read-only; + }; + + partition@6080000 { + label = "Cert"; + reg = <0x6080000 0x100000>; + read-only; + }; + + partition@6180000 { + label = "NTGRcryptK"; + reg = <0x6180000 0x100000>; + read-only; + }; + + partition@6280000 { + label = "NTGRcryptD"; + reg = <0x6280000 0x500000>; + read-only; + }; + + partition@6780000 { + label = "LOG"; + reg = <0x6780000 0x100000>; + read-only; + }; + + partition@6880000 { + label = "User_data"; + reg = <0x6880000 0x640000>; + read-only; + }; + }; +}; + +&pcie { + status = "okay"; +}; + +&pcie1 { + wifi@0,0 { + compatible = "mediatek,mt76"; + reg = <0x0000 0 0 0 0>; + nvmem-cells = <&eeprom_factory_0>, <&precal_factory_e10>; + nvmem-cell-names = "eeprom", "precal"; + }; +}; + +&state_default { + gpio { + groups = "uart3", "uart2", "jtag"; + function = "gpio"; + }; +}; + +&switch0 { + ports { + port@0 { + status = "okay"; + label = "lan"; + }; + }; +}; + +&xhci { + status = "disabled"; +}; diff --git a/target/linux/ramips/image/mt7621.mk b/target/linux/ramips/image/mt7621.mk index 3f3d5a0e2b..f9c58fa137 100644 --- a/target/linux/ramips/image/mt7621.mk +++ b/target/linux/ramips/image/mt7621.mk @@ -2113,6 +2113,24 @@ define Device/netgear_wax202 endef TARGET_DEVICES += netgear_wax202 +define Device/netgear_wax214v2 + $(Device/nand) + DEVICE_VENDOR := NETGEAR + DEVICE_MODEL := WAX214v2 + DEVICE_PACKAGES := kmod-mt7915-firmware + NETGEAR_ENC_MODEL := WAX214v2 + NETGEAR_ENC_REGION := US + IMAGE_SIZE := 38912k + KERNEL_LOADADDR := 0x82000000 + KERNEL := kernel-bin | relocate-kernel 0x80001000 | lzma | \ + fit lzma $$(KDIR)/image-$$(firstword $$(DEVICE_DTS)).dtb | \ + append-squashfs4-fakeroot + IMAGES += factory.img + IMAGE/factory.img := append-kernel | pad-to $$(KERNEL_SIZE) | \ + append-ubi | check-size | netgear-encrypted-factory +endef +TARGET_DEVICES += netgear_wax214v2 + define Device/netgear_wndr3700-v5 $(Device/dsa-migration) $(Device/netgear_sercomm_nor) diff --git a/target/linux/ramips/mt7621/base-files/etc/board.d/02_network b/target/linux/ramips/mt7621/base-files/etc/board.d/02_network index 386a3bb41d..1c5862f923 100644 --- a/target/linux/ramips/mt7621/base-files/etc/board.d/02_network +++ b/target/linux/ramips/mt7621/base-files/etc/board.d/02_network @@ -47,6 +47,7 @@ ramips_setup_interfaces() mikrotik,routerboard-m11g|\ netgear,eax12|\ netgear,ex6150|\ + netgear,wax214v2|\ sercomm,na502|\ sercomm,na502s|\ thunder,timecloud|\ @@ -325,6 +326,10 @@ ramips_setup_macs() wan_mac=$(macaddr_add "$lan_mac" 1) label_mac=$lan_mac ;; + netgear,wax214v2) + lan_mac=$(mtd_get_mac_ascii Config ethaddr) + label_mac=$lan_mac + ;; yuncore,ax820) label_mac=$(mtd_get_mac_binary Factory 0x4) ;; diff --git a/target/linux/ramips/mt7621/base-files/etc/hotplug.d/ieee80211/10_fix_wifi_mac b/target/linux/ramips/mt7621/base-files/etc/hotplug.d/ieee80211/10_fix_wifi_mac index 9350d67466..f8baf0046f 100644 --- a/target/linux/ramips/mt7621/base-files/etc/hotplug.d/ieee80211/10_fix_wifi_mac +++ b/target/linux/ramips/mt7621/base-files/etc/hotplug.d/ieee80211/10_fix_wifi_mac @@ -153,6 +153,11 @@ case "$board" in [ "$PHYNBR" = "0" ] && macaddr_add $hw_mac_addr 2 > /sys${DEVPATH}/macaddress [ "$PHYNBR" = "1" ] && macaddr_add $hw_mac_addr 3 > /sys${DEVPATH}/macaddress ;; + netgear,wax214v2) + hw_mac_addr=$(mtd_get_mac_ascii Config ethaddr) + [ "$PHYNBR" = "0" ] && macaddr_add $hw_mac_addr 2 > /sys${DEVPATH}/macaddress + [ "$PHYNBR" = "1" ] && macaddr_add $hw_mac_addr 3 > /sys${DEVPATH}/macaddress + ;; mercusys,mr70x-v1|\ tplink,archer-ax23-v1) hw_mac_addr="$(mtd_get_mac_binary config 0x8)" diff --git a/target/linux/ramips/mt7621/base-files/lib/upgrade/platform.sh b/target/linux/ramips/mt7621/base-files/lib/upgrade/platform.sh index 32dad72944..193082e665 100755 --- a/target/linux/ramips/mt7621/base-files/lib/upgrade/platform.sh +++ b/target/linux/ramips/mt7621/base-files/lib/upgrade/platform.sh @@ -122,6 +122,7 @@ platform_do_upgrade() { netgear,wac104|\ netgear,wac124|\ netgear,wax202|\ + netgear,wax214v2|\ netis,wf2881|\ raisecom,msg1500-x-00|\ rostelecom,rt-fe-1a|\