From: Daniel Golle Date: Sun, 23 Jul 2023 11:38:15 +0000 (+0100) Subject: mediatek: add support for BananaPi BPI-R4 board X-Git-Url: http://git.lede-project.org./?a=commitdiff_plain;h=f16dc4b42fb265affb2298e815a7ce0a13d60da6;p=openwrt%2Fstaging%2Fjow.git mediatek: add support for BananaPi BPI-R4 board Hardware -------- SOC: MediaTek MT7988A (4x Cortex-A73) RAM: 4 GiB DDR4 Flash: 128 MiB Winbond SPI-NAND MMC: 8 GiB eMMC *or* microSD (cannot be used both) ETH: 4x 1GE (1x WAN, 3x LAN) 2x SFP+ (10G, 5G, 2.5G, 1G) USB: on-board USB 3.2 4-port hub 1x USB 3.2 port (type A connector) 1x M.2 for 4G/5G modem 2x mPCIe for additional modems WiFi: optional MediaTek MT7996 Wi-Fi 7 module (using 2x PCIe gen3 x2 on the mPCIe slots and 12V power) Installation ------------ 1. Decompress and write the sdcard image to a micro SD card and use that to boot the R4 (both dip switches in upper position). 2. Use the bootloader menu accessible via the serial console to install to SPI-NAND. 3. Switch to boot from SPI-NAND and install to eMMC. Known issues ------------ - The RST button is hard-wired to the SoC reset and can't be read from software. This can be changed by modifying the board (ie. moving a 0-ohm resistor). However, in order to maintain compatibility with the board as it comes from factory the button isn't used by OpenWrt and the WPS button is used as factory/reset button instead. - various small things still need to be fixed in DT Signed-off-by: Daniel Golle --- diff --git a/target/linux/mediatek/files-6.1/arch/arm64/boot/dts/mediatek/mt7988a-bananapi-bpi-r4-emmc.dtso b/target/linux/mediatek/files-6.1/arch/arm64/boot/dts/mediatek/mt7988a-bananapi-bpi-r4-emmc.dtso new file mode 100644 index 0000000000..4945185d69 --- /dev/null +++ b/target/linux/mediatek/files-6.1/arch/arm64/boot/dts/mediatek/mt7988a-bananapi-bpi-r4-emmc.dtso @@ -0,0 +1,62 @@ +// SPDX-License-Identifier: (GPL-2.0 OR MIT) +/* + * Copyright (C) 2021 MediaTek Inc. + * Author: Frank Wunderlich + */ + +/dts-v1/; +/plugin/; + +/ { + compatible = "bananapi,bpi-r4", "mediatek,mt7988a"; + + fragment@0 { + target-path = "/soc/mmc@11230000"; + __overlay__ { + pinctrl-names = "default", "state_uhs"; + pinctrl-0 = <&mmc0_pins_emmc_51>; + pinctrl-1 = <&mmc0_pins_emmc_51>; + bus-width = <8>; + max-frequency = <200000000>; + cap-mmc-highspeed; + mmc-hs200-1_8v; + mmc-hs400-1_8v; + hs400-ds-delay = <0x12814>; + vqmmc-supply = <®_1p8v>; + vmmc-supply = <®_3p3v>; + non-removable; + no-sd; + no-sdio; + status = "okay"; + #address-cells = <1>; + #size-cells = <0>; + + card@0 { + compatible = "mmc-card"; + reg = <0>; + + block { + compatible = "block-device"; + partitions { + block-partition-env { + partname = "ubootenv"; + nvmem-layout { + compatible = "u-boot,env-layout"; + }; + }; + emmc_rootfs: block-partition-production { + partname = "production"; + }; + }; + }; + }; + }; + }; + + fragment@2 { + target-path = "/chosen"; + __overlay__ { + rootdisk-emmc = <&emmc_rootfs>; + }; + }; +}; diff --git a/target/linux/mediatek/files-6.1/arch/arm64/boot/dts/mediatek/mt7988a-bananapi-bpi-r4-rtc.dtso b/target/linux/mediatek/files-6.1/arch/arm64/boot/dts/mediatek/mt7988a-bananapi-bpi-r4-rtc.dtso new file mode 100644 index 0000000000..39910b8cfe --- /dev/null +++ b/target/linux/mediatek/files-6.1/arch/arm64/boot/dts/mediatek/mt7988a-bananapi-bpi-r4-rtc.dtso @@ -0,0 +1,19 @@ +// SPDX-License-Identifier: (GPL-2.0 OR MIT) +/* + * Copyright (C) 2023 + * Author: Daniel Golle + */ + +/dts-v1/; +/plugin/; + +/ { + compatible = "bananapi,bpi-r4", "mediatek,mt7988a"; + + fragment@0 { + target = <&pcf8563>; + __overlay__ { + status = "okay"; + }; + }; +}; diff --git a/target/linux/mediatek/files-6.1/arch/arm64/boot/dts/mediatek/mt7988a-bananapi-bpi-r4-sd.dtso b/target/linux/mediatek/files-6.1/arch/arm64/boot/dts/mediatek/mt7988a-bananapi-bpi-r4-sd.dtso new file mode 100644 index 0000000000..1f5e1491a4 --- /dev/null +++ b/target/linux/mediatek/files-6.1/arch/arm64/boot/dts/mediatek/mt7988a-bananapi-bpi-r4-sd.dtso @@ -0,0 +1,60 @@ +// SPDX-License-Identifier: (GPL-2.0 OR MIT) +/* + * Copyright (C) 2023 MediaTek Inc. + * Author: Frank Wunderlich + */ + +/dts-v1/; +/plugin/; + +#include + +/ { + compatible = "bananapi,bpi-r4", "mediatek,mt7988a"; + + fragment@1 { + target-path = "/soc/mmc@11230000"; + __overlay__ { + pinctrl-names = "default", "state_uhs"; + pinctrl-0 = <&mmc0_pins_sdcard>; + pinctrl-1 = <&mmc0_pins_sdcard>; + cd-gpios = <&pio 12 GPIO_ACTIVE_LOW>; + bus-width = <4>; + max-frequency = <52000000>; + cap-sd-highspeed; + vmmc-supply = <®_3p3v>; + vqmmc-supply = <®_3p3v>; + no-mmc; + status = "okay"; + #address-cells = <1>; + #size-cells = <0>; + + card@0 { + compatible = "mmc-card"; + reg = <0>; + + block { + compatible = "block-device"; + partitions { + block-partition-env { + partname = "ubootenv"; + nvmem-layout { + compatible = "u-boot,env-layout"; + }; + }; + sd_rootfs: block-partition-production { + partname = "production"; + }; + }; + }; + }; + }; + }; + + fragment@2 { + target-path = "/chosen"; + __overlay__ { + rootdisk-sd = <&sd_rootfs>; + }; + }; +}; diff --git a/target/linux/mediatek/files-6.1/arch/arm64/boot/dts/mediatek/mt7988a-bananapi-bpi-r4-wifi-mt7996a.dtso b/target/linux/mediatek/files-6.1/arch/arm64/boot/dts/mediatek/mt7988a-bananapi-bpi-r4-wifi-mt7996a.dtso new file mode 100644 index 0000000000..8a029b149f --- /dev/null +++ b/target/linux/mediatek/files-6.1/arch/arm64/boot/dts/mediatek/mt7988a-bananapi-bpi-r4-wifi-mt7996a.dtso @@ -0,0 +1,99 @@ +// SPDX-License-Identifier: (GPL-2.0 OR MIT) +/dts-v1/; +/plugin/; + +#include + +/ { + compatible = "bananapi,bpi-r4", "mediatek,mt7988a"; + + fragment@0 { + target-path = "/"; + __overlay__ { + wifi_12v: regulator-wifi-12v { + compatible = "regulator-fixed"; + regulator-name = "wifi"; + regulator-min-microvolt = <12000000>; + regulator-max-microvolt = <12000000>; + gpio = <&pio 4 GPIO_ACTIVE_HIGH>; + enable-active-high; + regulator-always-on; + }; + }; + }; + + fragment@1 { + target = <&i2c_wifi>; + __overlay__ { + // 5G WIFI MAC Address EEPROM + wifi_eeprom@51 { + compatible = "atmel,24c02"; + reg = <0x51>; + address-bits = <8>; + page-size = <8>; + size = <256>; + + nvmem-layout { + compatible = "fixed-layout"; + #address-cells = <1>; + #size-cells = <1>; + + macaddr_5g: macaddr@0 { + reg = <0x0 0x6>; + }; + }; + }; + + // 6G WIFI MAC Address EEPROM + wifi_eeprom@52 { + compatible = "atmel,24c02"; + reg = <0x52>; + address-bits = <8>; + page-size = <8>; + size = <256>; + + nvmem-layout { + compatible = "fixed-layout"; + #address-cells = <1>; + #size-cells = <1>; + + macaddr_6g: macaddr@0 { + reg = <0x0 0x6>; + }; + }; + }; + }; + }; + + fragment@2 { + target = <&pcie0>; + __overlay__ { + pcie@0,0 { + reg = <0x0000 0 0 0 0>; + + wifi@0,0 { + compatible = "mediatek,mt76"; + reg = <0x0000 0 0 0 0>; + nvmem-cell-names = "mac-address"; + nvmem-cells = <&macaddr_5g>; + }; + }; + }; + }; + + fragment@3 { + target = <&pcie1>; + __overlay__ { + pcie@0,0 { + reg = <0x0000 0 0 0 0>; + + wifi@0,0 { + compatible = "mediatek,mt76"; + reg = <0x0000 0 0 0 0>; + nvmem-cell-names = "mac-address"; + nvmem-cells = <&macaddr_6g>; + }; + }; + }; + }; +}; diff --git a/target/linux/mediatek/files-6.1/arch/arm64/boot/dts/mediatek/mt7988a-bananapi-bpi-r4.dts b/target/linux/mediatek/files-6.1/arch/arm64/boot/dts/mediatek/mt7988a-bananapi-bpi-r4.dts new file mode 100644 index 0000000000..b4bf3400ff --- /dev/null +++ b/target/linux/mediatek/files-6.1/arch/arm64/boot/dts/mediatek/mt7988a-bananapi-bpi-r4.dts @@ -0,0 +1,395 @@ +// SPDX-License-Identifier: (GPL-2.0 OR MIT) +/* + * Copyright (C) 2022 MediaTek Inc. + * Author: Sam.Shih + */ + +/dts-v1/; +#include "mt7988a.dtsi" +#include +#include +#include +#include + +/ { + model = "Bananapi BPI-R4"; + compatible = "bananapi,bpi-r4", + "mediatek,mt7988"; + + aliases { + serial0 = &uart0; + led-boot = &led_green; + led-failsafe = &led_green; + led-running = &led_green; + led-upgrade = &led_green; + }; + + chosen { + stdout-path = &uart0; + bootargs = "console=ttyS0,115200n1 loglevel=8 pci=pcie_bus_perf ubi.block=0,fit root=/dev/fit0"; + rootdisk-spim-nand = <&ubi_rootfs>; + }; + + memory { + reg = <0x00 0x40000000 0x00 0x10000000>; + }; + + /* SFP1 cage (WAN) */ + sfp1: sfp1 { + compatible = "sff,sfp"; + i2c-bus = <&i2c_sfp1>; + los-gpios = <&pio 54 GPIO_ACTIVE_HIGH>; + mod-def0-gpios = <&pio 82 GPIO_ACTIVE_LOW>; + tx-disable-gpios = <&pio 70 GPIO_ACTIVE_HIGH>; + tx-fault-gpios = <&pio 69 GPIO_ACTIVE_HIGH>; + rate-select0-gpios = <&pio 21 GPIO_ACTIVE_LOW>; + maximum-power-milliwatt = <3000>; + }; + + /* SFP2 cage (LAN) */ + sfp2: sfp2 { + compatible = "sff,sfp"; + i2c-bus = <&i2c_sfp2>; + los-gpios = <&pio 2 GPIO_ACTIVE_HIGH>; + mod-def0-gpios = <&pio 83 GPIO_ACTIVE_LOW>; + tx-disable-gpios = <&pio 0 GPIO_ACTIVE_HIGH>; + tx-fault-gpios = <&pio 1 GPIO_ACTIVE_HIGH>; + rate-select0-gpios = <&pio 3 GPIO_ACTIVE_LOW>; + maximum-power-milliwatt = <3000>; + }; + + gpio-keys { + compatible = "gpio-keys"; + + wps { + label = "WPS"; + linux,code = ; + gpios = <&pio 14 GPIO_ACTIVE_LOW>; + }; + }; + + gpio-leds { + compatible = "gpio-leds"; + + led_green: led-green { + function = LED_FUNCTION_STATUS; + color = ; + gpios = <&pio 79 GPIO_ACTIVE_HIGH>; + default-state = "on"; + }; + + led_blue: led-blue { + function = LED_FUNCTION_WPS; + color = ; + gpios = <&pio 63 GPIO_ACTIVE_HIGH>; + default-state = "off"; + }; + }; +}; + +ð { + status = "okay"; +}; + +&gmac0 { + status = "okay"; +}; + +&gmac1 { + sfp = <&sfp2>; + managed = "in-band-status"; + phy-mode = "usxgmii"; + status = "okay"; +}; + +&gmac2 { + sfp = <&sfp1>; + managed = "in-band-status"; + phy-mode = "usxgmii"; + status = "okay"; +}; + +&switch { + status = "okay"; +}; + +&gsw_phy0 { + pinctrl-names = "gbe-led"; + pinctrl-0 = <&gbe0_led0_pins>; +}; + +&gsw_port0 { + label = "wan"; +}; + +&gsw_phy0_led0 { + status = "okay"; + color = ; +}; + +&gsw_phy1 { + pinctrl-names = "gbe-led"; + pinctrl-0 = <&gbe1_led0_pins>; +}; + +&gsw_phy1_led0 { + status = "okay"; + color = ; +}; + +&gsw_phy2 { + pinctrl-names = "gbe-led"; + pinctrl-0 = <&gbe2_led0_pins>; +}; + +&gsw_phy2_led0 { + status = "okay"; + color = ; +}; + +&gsw_phy3 { + pinctrl-names = "gbe-led"; + pinctrl-0 = <&gbe3_led0_pins>; +}; + +&gsw_phy3_led0 { + status = "okay"; + color = ; +}; + +&cpu0 { + proc-supply = <&rt5190_buck3>; +}; + +&cpu1 { + proc-supply = <&rt5190_buck3>; +}; + +&cpu2 { + proc-supply = <&rt5190_buck3>; +}; + +&cpu3 { + proc-supply = <&rt5190_buck3>; +}; + +&cci { + proc-supply = <&rt5190_buck3>; +}; + +&i2c0 { + pinctrl-names = "default"; + pinctrl-0 = <&i2c0_pins>; + status = "okay"; + + rt5190a_64: rt5190a@64 { + compatible = "richtek,rt5190a"; + reg = <0x64>; + vin2-supply = <&rt5190_buck1>; + vin3-supply = <&rt5190_buck1>; + vin4-supply = <&rt5190_buck1>; + + regulators { + rt5190_buck1: buck1 { + regulator-name = "rt5190a-buck1"; + regulator-min-microvolt = <5090000>; + regulator-max-microvolt = <5090000>; + regulator-allowed-modes = + ; + regulator-boot-on; + regulator-always-on; + }; + buck2 { + regulator-name = "vcore"; + regulator-min-microvolt = <600000>; + regulator-max-microvolt = <1400000>; + regulator-boot-on; + regulator-always-on; + }; + rt5190_buck3: buck3 { + regulator-name = "vproc"; + regulator-min-microvolt = <600000>; + regulator-max-microvolt = <1400000>; + regulator-boot-on; + }; + buck4 { + regulator-name = "rt5190a-buck4"; + regulator-min-microvolt = <850000>; + regulator-max-microvolt = <850000>; + regulator-allowed-modes = + ; + regulator-boot-on; + regulator-always-on; + }; + ldo { + regulator-name = "rt5190a-ldo"; + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1200000>; + regulator-boot-on; + regulator-always-on; + }; + }; + }; +}; + +&i2c2 { + pinctrl-names = "default"; + pinctrl-0 = <&i2c2_1_pins>; + status = "okay"; + + pca9545: i2c-switch@70 { + reg = <0x70>; + compatible = "nxp,pca9545"; + reset-gpios = <&pio 5 GPIO_ACTIVE_LOW>; + #address-cells = <1>; + #size-cells = <0>; + + i2c_rtc: i2c@0 { //eeprom,rtc,ngff + #address-cells = <1>; + #size-cells = <0>; + reg = <0>; + + eeprom@50 { + compatible = "atmel,24c02"; + reg = <0x50>; + address-bits = <8>; + page-size = <8>; + size = <256>; + }; + + eeprom@57 { + compatible = "atmel,24c02"; + reg = <0x57>; + address-bits = <8>; + page-size = <8>; + size = <256>; + }; + + pcf8563: rtc@51 { + compatible = "nxp,pcf8563"; + reg = <0x51>; + status = "disabled"; + }; + }; + + i2c_sfp1: i2c@1 { + #address-cells = <1>; + #size-cells = <0>; + reg = <1>; + }; + + i2c_sfp2: i2c@2 { + #address-cells = <1>; + #size-cells = <0>; + reg = <2>; + }; + + i2c_wifi: i2c@3 { + #address-cells = <1>; + #size-cells = <0>; + reg = <3>; + }; + }; +}; + +/* mPCIe SIM2 */ +&pcie0 { + pinctrl-names = "default"; + pinctrl-0 = <&pcie0_pins>; + status = "okay"; +}; + +/* mPCIe SIM3 */ +&pcie1 { + pinctrl-names = "default"; + pinctrl-0 = <&pcie1_pins>; + status = "okay"; +}; + +/* M.2 key-B SIM1 */ +&pcie2 { + pinctrl-names = "default"; + pinctrl-0 = <&pcie2_pins>; + status = "okay"; +}; + +/* M.2 key-M SSD */ +&pcie3 { + pinctrl-names = "default"; + pinctrl-0 = <&pcie3_pins>; + status = "okay"; +}; + +&ssusb1 { + status = "okay"; +}; + +&tphy { + status = "okay"; +}; + +&spi0 { + pinctrl-names = "default"; + pinctrl-0 = <&spi0_flash_pins>; + status = "okay"; + + spi_nand: spi_nand@0 { + compatible = "spi-nand"; + reg = <0>; + spi-max-frequency = <52000000>; + spi-tx-buswidth = <4>; + spi-rx-buswidth = <4>; + }; +}; + +&spi_nand { + partitions { + compatible = "fixed-partitions"; + #address-cells = <1>; + #size-cells = <1>; + + partition@0 { + label = "bl2"; + reg = <0x0 0x200000>; + read-only; + }; + + partition@200000 { + label = "ubi"; + reg = <0x200000 0x7e00000>; + compatible = "linux,ubi"; + + volumes { + ubi-volume-ubootenv { + volname = "ubootenv"; + nvmem-layout { + compatible = "u-boot,env-redundant-bool-layout"; + }; + }; + + ubi-volume-ubootenv2 { + volname = "ubootenv2"; + nvmem-layout { + compatible = "u-boot,env-redundant-bool-layout"; + }; + }; + + ubi_rootfs: ubi-volume-fit { + volname = "fit"; + }; + }; + }; + }; +}; + +&uart0 { + status = "okay"; +}; + +&watchdog { + status = "okay"; +}; + +&xphy { + status = "okay"; +}; diff --git a/target/linux/mediatek/files-6.1/arch/arm64/boot/dts/mediatek/mt7988a.dtsi b/target/linux/mediatek/files-6.1/arch/arm64/boot/dts/mediatek/mt7988a.dtsi index 8f1c1ddc9d..76278281df 100644 --- a/target/linux/mediatek/files-6.1/arch/arm64/boot/dts/mediatek/mt7988a.dtsi +++ b/target/linux/mediatek/files-6.1/arch/arm64/boot/dts/mediatek/mt7988a.dtsi @@ -1230,28 +1230,28 @@ #address-cells = <1>; #size-cells = <0>; - port@0 { + gsw_port0: port@0 { reg = <0>; label = "lan0"; phy-mode = "internal"; phy-handle = <&gsw_phy0>; }; - port@1 { + gsw_port1: port@1 { reg = <1>; label = "lan1"; phy-mode = "internal"; phy-handle = <&gsw_phy1>; }; - port@2 { + gsw_port2: port@2 { reg = <2>; label = "lan2"; phy-mode = "internal"; phy-handle = <&gsw_phy2>; }; - port@3 { + gsw_port3: port@3 { reg = <3>; label = "lan3"; phy-mode = "internal"; diff --git a/target/linux/mediatek/filogic/base-files/etc/board.d/01_leds b/target/linux/mediatek/filogic/base-files/etc/board.d/01_leds index b9fac1bebf..3622bf9a71 100644 --- a/target/linux/mediatek/filogic/base-files/etc/board.d/01_leds +++ b/target/linux/mediatek/filogic/base-files/etc/board.d/01_leds @@ -12,6 +12,12 @@ confiabits,mt7981) ucidef_set_led_netdev "lan3" "lan3" "blue:lan-3" "lan3" "link tx rx" ucidef_set_led_netdev "wan" "wan" "blue:wan" "wan" "link tx rx" ;; +bananapi,bpi-r4) + ucidef_set_led_netdev "wan" "wan" "mt7530-0:00:green:lan" "wan" "link tx rx" + ucidef_set_led_netdev "lan1" "lan1" "mt7530-0:01:green:lan" "lan1" "link tx rx" + ucidef_set_led_netdev "lan2" "lan2" "mt7530-0:02:green:lan" "lan2" "link tx rx" + ucidef_set_led_netdev "lan3" "lan3" "mt7530-0:03:green:lan" "lan3" "link tx rx" + ;; cudy,wr3000-v1) ucidef_set_led_netdev "wan" "wan" "blue:wan" "wan" ;; diff --git a/target/linux/mediatek/filogic/base-files/etc/board.d/02_network b/target/linux/mediatek/filogic/base-files/etc/board.d/02_network index a9cf0d2305..01240d003a 100644 --- a/target/linux/mediatek/filogic/base-files/etc/board.d/02_network +++ b/target/linux/mediatek/filogic/base-files/etc/board.d/02_network @@ -35,6 +35,9 @@ mediatek_setup_interfaces() bananapi,bpi-r3) ucidef_set_interfaces_lan_wan "lan1 lan2 lan3 lan4 sfp2" "eth1 wan" ;; + bananapi,bpi-r4) + ucidef_set_interfaces_lan_wan "lan1 lan2 lan3 eth1" "wan eth2" + ;; cmcc,rax3000m|\ h3c,magic-nx30-pro|\ zbtlink,zbt-z8103ax) diff --git a/target/linux/mediatek/filogic/base-files/lib/upgrade/platform.sh b/target/linux/mediatek/filogic/base-files/lib/upgrade/platform.sh index 97c09f35a8..889a1e2bd1 100755 --- a/target/linux/mediatek/filogic/base-files/lib/upgrade/platform.sh +++ b/target/linux/mediatek/filogic/base-files/lib/upgrade/platform.sh @@ -1,4 +1,5 @@ REQUIRE_IMAGE_METADATA=1 +RAMFS_COPY_BIN='fitblk' asus_initial_setup() { @@ -59,6 +60,21 @@ xiaomi_initial_setup() esac } +platform_get_bootdev() { + local rootdisk="$(cat /sys/firmware/devicetree/base/chosen/rootdisk)" + local handle bootdev + for handle in /sys/class/block/*/of_node/phandle /sys/class/block/*/device/of_node/phandle; do + [ ! -e "$handle" ] && continue + if [ "$rootdisk" = "$(cat $handle)" ]; then + bootdev="${handle%/of_node/phandle}" + bootdev="${bootdev%/device}" + bootdev="${bootdev#/sys/class/block/}" + echo "$bootdev" + break + fi + done +} + platform_do_upgrade() { local board=$(board_name) @@ -99,6 +115,21 @@ platform_do_upgrade() { ;; esac ;; + bananapi,bpi-r4) + [ -e /dev/fit0 ] && fitblk /dev/fit0 + [ -e /dev/fitrw ] && fitblk /dev/fitrw + bootdev="$(platform_get_bootdev)" + case "$bootdev" in + mmcblk*) + EMMC_KERN_DEV="/dev/$bootdev" + emmc_do_upgrade "$1" + ;; + ubiblock*) + CI_KERNPART="fit" + nand_do_upgrade "$1" + ;; + esac + ;; cmcc,rax3000m) case "$(cmdline_get_var root)" in /dev/mmc*) @@ -175,6 +206,7 @@ platform_check_image() { case "$board" in bananapi,bpi-r3|\ + bananapi,bpi-r4|\ cmcc,rax3000m) [ "$magic" != "d00dfeed" ] && { echo "Invalid image type." @@ -201,6 +233,13 @@ platform_copy_config() { ;; esac ;; + bananapi,bpi-r4) + case "$(platform_get_bootdev)" in + mmcblk*) + emmc_copy_config + ;; + esac + ;; acer,predator-w6|\ glinet,gl-mt2500|\ glinet,gl-mt6000|\ diff --git a/target/linux/mediatek/filogic/config-6.1 b/target/linux/mediatek/filogic/config-6.1 index b75ef6b610..9e27cd830c 100644 --- a/target/linux/mediatek/filogic/config-6.1 +++ b/target/linux/mediatek/filogic/config-6.1 @@ -44,6 +44,7 @@ CONFIG_AUDIT_ARCH_COMPAT_GENERIC=y CONFIG_BLK_DEV_LOOP=y CONFIG_BLK_DEV_SD=y CONFIG_BLK_MQ_PCI=y +CONFIG_BLK_NVMEM=y CONFIG_BLK_PM=y CONFIG_BSD_PROCESS_ACCT=y CONFIG_BSD_PROCESS_ACCT_V3=y @@ -254,6 +255,7 @@ CONFIG_MTD_UBI=y CONFIG_MTD_UBI_BEB_LIMIT=20 CONFIG_MTD_UBI_BLOCK=y CONFIG_MTD_UBI_FASTMAP=y +CONFIG_MTD_UBI_NVMEM=y CONFIG_MTD_UBI_WL_THRESHOLD=4096 # CONFIG_MTK_CMDQ is not set # CONFIG_MTK_CQDMA is not set @@ -462,6 +464,7 @@ CONFIG_TREE_RCU=y CONFIG_TREE_SRCU=y CONFIG_UBIFS_FS=y # CONFIG_UCLAMP_TASK is not set +CONFIG_UIMAGE_FIT_BLK=y # CONFIG_UNMAP_KERNEL_AT_EL0 is not set CONFIG_USB_SUPPORT=y CONFIG_VMAP_STACK=y diff --git a/target/linux/mediatek/image/filogic.mk b/target/linux/mediatek/image/filogic.mk index 90a0e91f02..0d36199f0d 100644 --- a/target/linux/mediatek/image/filogic.mk +++ b/target/linux/mediatek/image/filogic.mk @@ -272,6 +272,51 @@ endif endef TARGET_DEVICES += bananapi_bpi-r3 +define Device/bananapi_bpi-r4 + DEVICE_VENDOR := Bananapi + DEVICE_MODEL := BPi-R4 + DEVICE_DTS := mt7988a-bananapi-bpi-r4 + DEVICE_DTS_CONFIG := config-mt7988a-bananapi-bpi-r4 + DEVICE_DTS_DIR := $(DTS_DIR)/ + DEVICE_DTS_LOADADDR := 0x45f00000 + DEVICE_DTS_OVERLAY:= mt7988a-bananapi-bpi-r4-emmc mt7988a-bananapi-bpi-r4-rtc mt7988a-bananapi-bpi-r4-sd mt7988a-bananapi-bpi-r4-wifi-mt7996a + DEVICE_DTC_FLAGS := --pad 4096 + DEVICE_PACKAGES := fitblk kmod-hwmon-pwmfan kmod-i2c-mux-pca954x kmod-eeprom-at24 kmod-mt7996-firmware \ + kmod-rtc-pcf8563 kmod-sfp kmod-usb3 e2fsprogs f2fsck mkf2fs + IMAGES := sysupgrade.itb + KERNEL_LOADADDR := 0x46000000 + KERNEL_INITRAMFS_SUFFIX := -recovery.itb + ARTIFACTS := \ + emmc-preloader.bin emmc-bl31-uboot.fip \ + sdcard.img.gz \ + snand-preloader.bin snand-bl31-uboot.fip + ARTIFACT/emmc-preloader.bin := mt7988-bl2 emmc-comb + ARTIFACT/emmc-bl31-uboot.fip := mt7988-bl31-uboot bananapi_bpi-r4-emmc + ARTIFACT/snand-preloader.bin := mt7988-bl2 spim-nand-ubi-comb + ARTIFACT/snand-bl31-uboot.fip := mt7988-bl31-uboot bananapi_bpi-r4-snand + ARTIFACT/sdcard.img.gz := mt798x-gpt sdmmc |\ + pad-to 17k | mt7988-bl2 sdmmc-comb |\ + pad-to 6656k | mt7988-bl31-uboot bananapi_bpi-r4-sdmmc |\ + $(if $(CONFIG_TARGET_ROOTFS_INITRAMFS),\ + pad-to 12M | append-image-stage initramfs-recovery.itb | check-size 44m |\ + ) \ + pad-to 44M | mt7988-bl2 spim-nand-ubi-comb |\ + pad-to 45M | mt7988-bl31-uboot bananapi_bpi-r4-snand |\ + pad-to 51M | mt7988-bl2 emmc-comb |\ + pad-to 52M | mt7988-bl31-uboot bananapi_bpi-r4-emmc |\ + pad-to 56M | mt798x-gpt emmc |\ + $(if $(CONFIG_TARGET_ROOTFS_SQUASHFS),\ + pad-to 64M | append-image squashfs-sysupgrade.itb | check-size |\ + ) \ + gzip + IMAGE_SIZE := $$(shell expr 64 + $$(CONFIG_TARGET_ROOTFS_PARTSIZE))m + KERNEL := kernel-bin | gzip + KERNEL_INITRAMFS := kernel-bin | lzma | \ + fit lzma $$(KDIR)/image-$$(firstword $$(DEVICE_DTS)).dtb with-initrd | pad-to 64k + IMAGE/sysupgrade.itb := append-kernel | fit gzip $$(KDIR)/image-$$(firstword $$(DEVICE_DTS)).dtb external-with-rootfs | pad-rootfs | append-metadata +endef +TARGET_DEVICES += bananapi_bpi-r4 + define Device/cetron_ct3003 DEVICE_VENDOR := Cetron DEVICE_MODEL := CT3003