From: Dongming Han Date: Wed, 8 Apr 2020 08:43:51 +0000 (+0800) Subject: ipq40xx: add support for GL.iNet GL-S1300 X-Git-Url: http://git.lede-project.org./?a=commitdiff_plain;h=f103321349182d5fef5a1b846f017db32005da87;p=openwrt%2Fstaging%2Fwigyori.git ipq40xx: add support for GL.iNet GL-S1300 Specifications: SOC: Qualcomm IPQ4029 (DAKOTA) ARM Quad-Core RAM: 512 MiB FLASH1: 16 MiB NOR - SPI0 FLASH2: 8 GiB eMMC ETH: Qualcomm QCA8075 WLAN1: Qualcomm Atheros QCA4029 2.4GHz 802.11b/g/n 2x2 WLAN2: Qualcomm Atheros QCA4029 5GHz 802.11n/ac W2 2x2 INPUT: Reset, WPS LED: Power, Mesh, WLAN UART1: On board pin header near to LED (3.3V, TX, RX, GND), 3.3V without pin - 115200 8N1 UART2: On board with BLE module SPI1: On board socket for Zigbee module Install via tftp - NB: need to flash transition image firstly Firstly install transition image: (IPQ40xx) # tftpboot 0x84000000 s1300-factory-to-openwrt.img (IPQ40xx) # sf probe && imgaddr=0x84000000 && source :script Secondly install openwrt sysupgrade bin: (IPQ40xx) # run lf Revert to factory image: (IPQ40xx) # tftpboot 0x84000000 s1300-openwrt-to-factory.img (IPQ40xx) # sf probe && imgaddr=0x84000000 && source :script The kernel and rootfs of factory firmware are on eMMC, and openwrt firmware is on NOR flash. The transition image includes U-boot and partition table, which decides where to load kernel and rootfs. After you firstly install openwrt image, you can switch between factory and openwrt firmware by flashing transition image. Signed-off-by: Dongming Han --- diff --git a/package/firmware/ipq-wifi/Makefile b/package/firmware/ipq-wifi/Makefile index c86645e253..4868b75d16 100644 --- a/package/firmware/ipq-wifi/Makefile +++ b/package/firmware/ipq-wifi/Makefile @@ -34,6 +34,7 @@ ALLWIFIBOARDS:= \ engenius_emd1 \ engenius_emr3500 \ ezviz_cs-w3-wd1200g-eup \ + glinet_gl-s1300 \ linksys_ea8300 \ mobipromo_cm520-79f \ qxwlan_e2600ac @@ -106,6 +107,7 @@ $(eval $(call generate-ipq-wifi-package,engenius_eap2200,EnGenius EAP2200)) $(eval $(call generate-ipq-wifi-package,engenius_emd1,EnGenius EMD1)) $(eval $(call generate-ipq-wifi-package,engenius_emr3500,EnGenius EMR3500)) $(eval $(call generate-ipq-wifi-package,ezviz_cs-w3-wd1200g-eup,EZVIZ CS-W3-WD1200G EUP)) +$(eval $(call generate-ipq-wifi-package,glinet_gl-s1300,GL.iNet GL-S1300)) $(eval $(call generate-ipq-wifi-package,linksys_ea8300,Linksys EA8300)) $(eval $(call generate-ipq-wifi-package,mobipromo_cm520-79f,MobiPromo CM520-79F)) $(eval $(call generate-ipq-wifi-package,qxwlan_e2600ac,Qxwlan E2600AC)) diff --git a/package/firmware/ipq-wifi/board-glinet_gl-s1300.qca4019 b/package/firmware/ipq-wifi/board-glinet_gl-s1300.qca4019 new file mode 100644 index 0000000000..b84e62f825 Binary files /dev/null and b/package/firmware/ipq-wifi/board-glinet_gl-s1300.qca4019 differ diff --git a/target/linux/ipq40xx/base-files/etc/board.d/02_network b/target/linux/ipq40xx/base-files/etc/board.d/02_network index 77a2241283..cd336a9e6a 100755 --- a/target/linux/ipq40xx/base-files/etc/board.d/02_network +++ b/target/linux/ipq40xx/base-files/etc/board.d/02_network @@ -75,7 +75,8 @@ ipq40xx_setup_interfaces() ucidef_add_switch "switch0" \ "0u@eth0" "2:lan:3" "3:lan:2" "4:lan:1" "0u@eth1" "5:wan" ;; - glinet,gl-b1300) + glinet,gl-b1300 |\ + glinet,gl-s1300) ucidef_set_interfaces_lan_wan "eth0" "eth1" ucidef_add_switch "switch0" \ "0u@eth0" "3:lan" "4:lan" diff --git a/target/linux/ipq40xx/base-files/etc/hotplug.d/firmware/11-ath10k-caldata b/target/linux/ipq40xx/base-files/etc/hotplug.d/firmware/11-ath10k-caldata index e41baecf69..b95bab7cae 100644 --- a/target/linux/ipq40xx/base-files/etc/hotplug.d/firmware/11-ath10k-caldata +++ b/target/linux/ipq40xx/base-files/etc/hotplug.d/firmware/11-ath10k-caldata @@ -50,6 +50,7 @@ case "$FIRMWARE" in cilab,meshpoint-one |\ ezviz,cs-w3-wd1200g-eup |\ glinet,gl-b1300 |\ + glinet,gl-s1300 |\ linksys,ea6350v3 |\ mobipromo,cm520-79f |\ qcom,ap-dk01.1-c1) @@ -138,6 +139,7 @@ case "$FIRMWARE" in cilab,meshpoint-one |\ ezviz,cs-w3-wd1200g-eup |\ glinet,gl-b1300 |\ + glinet,gl-s1300 |\ linksys,ea6350v3 |\ mobipromo,cm520-79f |\ qcom,ap-dk01.1-c1) diff --git a/target/linux/ipq40xx/files/arch/arm/boot/dts/qcom-ipq4029-gl-s1300.dts b/target/linux/ipq40xx/files/arch/arm/boot/dts/qcom-ipq4029-gl-s1300.dts new file mode 100644 index 0000000000..3457ebebfe --- /dev/null +++ b/target/linux/ipq40xx/files/arch/arm/boot/dts/qcom-ipq4029-gl-s1300.dts @@ -0,0 +1,356 @@ +// SPDX-License-Identifier: GPL-2.0 OR MIT + +#include "qcom-ipq4019.dtsi" +#include +#include +#include + +/ { + model = "GL.iNet GL-S1300"; + compatible = "glinet,gl-s1300"; + + aliases { + led-boot = &led_power; + led-failsafe = &led_power; + led-running = &led_power; + led-upgrade = &led_power; + }; + + memory { + device_type = "memory"; + reg = <0x80000000 0x10000000>; + }; + + soc { + rng@22000 { + status = "okay"; + }; + + mdio@90000 { + status = "okay"; + }; + + ess-psgmii@98000 { + status = "okay"; + }; + + tcsr@1949000 { + compatible = "qcom,tcsr"; + reg = <0x1949000 0x100>; + qcom,wifi_glb_cfg = ; + }; + + tcsr@194b000 { + /* select hostmode */ + compatible = "qcom,tcsr"; + reg = <0x194b000 0x100>; + qcom,usb-hsphy-mode-select = ; + status = "okay"; + }; + + ess_tcsr@1953000 { + compatible = "qcom,tcsr"; + reg = <0x1953000 0x1000>; + qcom,ess-interface-select = ; + }; + + tcsr@1957000 { + compatible = "qcom,tcsr"; + reg = <0x1957000 0x100>; + qcom,wifi_noc_memtype_m0_m2 = ; + }; + + usb2@60f8800 { + status = "okay"; + }; + + usb3@8af8800 { + status = "okay"; + }; + + crypto@8e3a000 { + status = "okay"; + }; + + watchdog@b017000 { + status = "okay"; + }; + + ess-switch@c000000 { + status = "okay"; + switch_lan_bmp = <0x18>; + switch_wan_bmp = <0x20>; + }; + + edma@c080000 { + status = "okay"; + }; + }; + + keys { + compatible = "gpio-keys"; + + wps { + label = "wps"; + gpios = <&tlmm 53 GPIO_ACTIVE_LOW>; + linux,code = ; + }; + + reset { + label = "reset"; + gpios = <&tlmm 18 GPIO_ACTIVE_LOW>; + linux,code = ; + }; + }; + + leds { + compatible = "gpio-leds"; + + led_power: power { + label = "gl-s1300:green:power"; + gpios = <&tlmm 57 GPIO_ACTIVE_HIGH>; + default-state = "on"; + }; + + mesh { + label = "gl-s1300:green:mesh"; + gpios = <&tlmm 59 GPIO_ACTIVE_HIGH>; + }; + + wlan { + label = "gl-s1300:green:wlan"; + gpios = <&tlmm 60 GPIO_ACTIVE_HIGH>; + linux,default-trigger = "phy0tpt"; + }; + }; +}; + +&vqmmc { + status = "okay"; +}; + +&sdhci { + status = "okay"; + pinctrl-0 = <&sd_pins>; + pinctrl-names = "default"; + cd-gpios = <&tlmm 22 GPIO_ACTIVE_LOW>; + vqmmc-supply = <&vqmmc>; +}; + +&blsp_dma { + status = "okay"; +}; + +&cryptobam { + status = "okay"; +}; + +&blsp1_spi1 { + pinctrl-0 = <&spi_0_pins>; + pinctrl-names = "default"; + status = "okay"; + cs-gpios = <&tlmm 12 GPIO_ACTIVE_HIGH>; + + flash@0 { + compatible = "jedec,spi-nor"; + reg = <0>; + spi-max-frequency = <24000000>; + + partitions { + compatible = "fixed-partitions"; + #address-cells = <1>; + #size-cells = <1>; + + SBL1@0 { + label = "SBL1"; + reg = <0x0 0x40000>; + read-only; + }; + + MIBIB@40000 { + label = "MIBIB"; + reg = <0x40000 0x20000>; + read-only; + }; + + QSEE@60000 { + label = "QSEE"; + reg = <0x60000 0x60000>; + read-only; + }; + + CDT@c0000 { + label = "CDT"; + reg = <0xc0000 0x10000>; + read-only; + }; + + DDRPARAMS@d0000 { + label = "DDRPARAMS"; + reg = <0xd0000 0x10000>; + read-only; + }; + + APPSBLENV@e0000 { + label = "APPSBLENV"; + reg = <0xe0000 0x10000>; + read-only; + }; + + APPSBL@f0000 { + label = "APPSBL"; + reg = <0xf0000 0x80000>; + read-only; + }; + + ART@170000 { + label = "ART"; + reg = <0x170000 0x10000>; + read-only; + }; + + firmware@180000 { + compatible = "denx,fit"; + label = "firmware"; + reg = <0x180000 0xe80000>; + }; + }; + }; +}; + +&blsp1_spi2 { + pinctrl-0 = <&spi_1_pins>; + pinctrl-names = "default"; + status = "okay"; + + spidev1: spi@1 { + compatible = "siliconlabs,si3210"; + reg = <0>; + spi-max-frequency = <24000000>; + }; +}; + +&blsp1_uart1 { + pinctrl-0 = <&serial_pins>; + pinctrl-names = "default"; + status = "okay"; +}; + +&blsp1_uart2 { + pinctrl-0 = <&serial_1_pins>; + pinctrl-names = "default"; + status = "okay"; +}; + +&tlmm { + serial_pins: serial_pinmux { + mux { + pins = "gpio16", "gpio17"; + function = "blsp_uart0"; + bias-disable; + }; + }; + + serial_1_pins: serial1_pinmux { + mux { + pins = "gpio8", "gpio9", + "gpio10", "gpio11"; + function = "blsp_uart1"; + bias-disable; + }; + }; + + spi_0_pins: spi_0_pinmux { + pinmux { + function = "blsp_spi0"; + pins = "gpio13", "gpio14", "gpio15"; + }; + pinmux_cs { + function = "gpio"; + pins = "gpio12"; + }; + pinconf { + pins = "gpio13", "gpio14", "gpio15"; + drive-strength = <12>; + bias-disable; + }; + pinconf_cs { + pins = "gpio12"; + drive-strength = <2>; + bias-disable; + output-high; + }; + }; + + spi_1_pins: spi_1_pinmux { + mux { + pins = "gpio44", "gpio46", "gpio47"; + function = "blsp_spi1"; + bias-disable; + }; + host_int { + pins = "gpio42"; + function = "gpio"; + input; + }; + cs { + pins = "gpio45"; + function = "gpio"; + bias-pull-up; + }; + wake { + pins = "gpio40"; + function = "gpio"; + output-high; + }; + reset { + pins = "gpio49"; + function = "gpio"; + output-high; + }; + }; + + sd_pins: sd_pins { + pinmux { + function = "sdio"; + pins = "gpio23", "gpio24", "gpio25", "gpio26", + "gpio28", "gpio29", "gpio30", "gpio31"; + drive-strength = <10>; + }; + + pinmux_sd_clk { + function = "sdio"; + pins = "gpio27"; + drive-strength = <16>; + }; + + pinmux_sd7 { + function = "sdio"; + pins = "gpio32"; + drive-strength = <10>; + bias-disable; + }; + }; +}; + +&usb2_hs_phy { + status = "okay"; +}; + +&usb3_hs_phy { + status = "okay"; +}; + +&usb3_ss_phy { + status = "okay"; +}; + +&wifi0 { + status = "okay"; + qcom,ath10k-calibration-variant = "GL-S1300"; +}; + +&wifi1 { + status = "okay"; + qcom,ath10k-calibration-variant = "GL-S1300"; +}; diff --git a/target/linux/ipq40xx/image/Makefile b/target/linux/ipq40xx/image/Makefile index a374c7da47..5336649c3d 100644 --- a/target/linux/ipq40xx/image/Makefile +++ b/target/linux/ipq40xx/image/Makefile @@ -437,6 +437,19 @@ define Device/glinet_gl-b1300 endef TARGET_DEVICES += glinet_gl-b1300 +define Device/glinet_gl-s1300 + $(call Device/FitImage) + DEVICE_VENDOR := GL.iNet + DEVICE_MODEL := GL-S1300 + SOC := qcom-ipq4029 + KERNEL_SIZE := 4096k + IMAGE_SIZE := 26624k + IMAGES := sysupgrade.bin + IMAGE/sysupgrade.bin := append-kernel | append-rootfs | pad-rootfs | append-metadata + DEVICE_PACKAGES := ipq-wifi-glinet_gl-s1300 kmod-fs-ext4 kmod-mmc kmod-spi-dev +endef +TARGET_DEVICES += glinet_gl-s1300 + define Device/linksys_ea6350v3 # The Linksys EA6350v3 has a uboot bootloader that does not # support either booting lzma kernel images nor booting UBI diff --git a/target/linux/ipq40xx/patches-4.19/901-arm-boot-add-dts-files.patch b/target/linux/ipq40xx/patches-4.19/901-arm-boot-add-dts-files.patch index 2ec1007191..fb358ed184 100644 --- a/target/linux/ipq40xx/patches-4.19/901-arm-boot-add-dts-files.patch +++ b/target/linux/ipq40xx/patches-4.19/901-arm-boot-add-dts-files.patch @@ -10,7 +10,7 @@ Signed-off-by: John Crispin --- a/arch/arm/boot/dts/Makefile +++ b/arch/arm/boot/dts/Makefile -@@ -785,11 +785,47 @@ dtb-$(CONFIG_ARCH_QCOM) += \ +@@ -785,11 +785,48 @@ dtb-$(CONFIG_ARCH_QCOM) += \ qcom-apq8074-dragonboard.dtb \ qcom-apq8084-ifc6540.dtb \ qcom-apq8084-mtp.dtb \ @@ -54,6 +54,7 @@ Signed-off-by: John Crispin + qcom-ipq4029-ap-303h.dtb \ + qcom-ipq4029-ap-365.dtb \ + qcom-ipq4029-gl-b1300.dtb \ ++ qcom-ipq4029-gl-s1300.dtb \ + qcom-ipq4029-mr33.dtb \ qcom-ipq8064-ap148.dtb \ qcom-msm8660-surf.dtb \ diff --git a/target/linux/ipq40xx/patches-5.4/901-arm-boot-add-dts-files.patch b/target/linux/ipq40xx/patches-5.4/901-arm-boot-add-dts-files.patch index 371faa3a09..2db36aa597 100644 --- a/target/linux/ipq40xx/patches-5.4/901-arm-boot-add-dts-files.patch +++ b/target/linux/ipq40xx/patches-5.4/901-arm-boot-add-dts-files.patch @@ -10,7 +10,7 @@ Signed-off-by: John Crispin --- a/arch/arm/boot/dts/Makefile +++ b/arch/arm/boot/dts/Makefile -@@ -837,11 +837,48 @@ dtb-$(CONFIG_ARCH_QCOM) += \ +@@ -837,11 +837,49 @@ dtb-$(CONFIG_ARCH_QCOM) += \ qcom-apq8074-dragonboard.dtb \ qcom-apq8084-ifc6540.dtb \ qcom-apq8084-mtp.dtb \ @@ -55,6 +55,7 @@ Signed-off-by: John Crispin + qcom-ipq4029-ap-303h.dtb \ + qcom-ipq4029-ap-365.dtb \ + qcom-ipq4029-gl-b1300.dtb \ ++ qcom-ipq4029-gl-s1300.dtb \ + qcom-ipq4029-mr33.dtb \ qcom-ipq8064-ap148.dtb \ qcom-msm8660-surf.dtb \