From: Guennadi Liakhovetski Date: Thu, 10 Jan 2008 16:59:07 +0000 (+0100) Subject: Add support for the TK885D baseboard from TELE-DATA X-Git-Url: http://git.lede-project.org./?a=commitdiff_plain;h=efc6f447c1b940d1650c4b854c5598a595ddc3da;p=project%2Fbcm63xx%2Fu-boot.git Add support for the TK885D baseboard from TELE-DATA The TK885D board uses a TQM885D module from TQ, this port adds an own configuration file and adds a last_stage_init() method to configure the two PHYs, depending on the phy_auto_nego environment variable. Signed-off-by: Guennadi Liakhovetski --- diff --git a/MAKEALL b/MAKEALL index 6013d49f52..cb1322d7c9 100755 --- a/MAKEALL +++ b/MAKEALL @@ -135,6 +135,7 @@ LIST_8xx=" \ SPD823TS \ svm_sc8xx \ SXNI855T \ + TK885D \ TOP860 \ TQM823L \ TQM823L_LCD \ diff --git a/Makefile b/Makefile index 47206fc760..fa12ed7cef 100644 --- a/Makefile +++ b/Makefile @@ -1062,6 +1062,7 @@ TQM860M_config \ TQM862M_config \ TQM866M_config \ TQM885D_config \ +TK885D_config \ virtlab2_config: unconfig @mkdir -p $(obj)include @ >$(obj)include/config.h diff --git a/board/tqm8xx/tqm8xx.c b/board/tqm8xx/tqm8xx.c index fcd941e0d2..18bf2a8302 100644 --- a/board/tqm8xx/tqm8xx.c +++ b/board/tqm8xx/tqm8xx.c @@ -504,4 +504,51 @@ int misc_init_r (void) } #endif /* CONFIG_NSCU */ +/* ---------------------------------------------------------------------------- */ +/* TK885D specific initializaion */ +/* ---------------------------------------------------------------------------- */ +#ifdef CONFIG_TK885D +#include +int last_stage_init(void) +{ + const unsigned char phy[] = {CONFIG_FEC1_PHY, CONFIG_FEC2_PHY}; + unsigned short reg; + int ret, i = 100; + char *s; + + mii_init(); + /* Without this delay 0xff is read from the UART buffer later in + * abortboot() and autoboot is aborted */ + udelay(10000); + while (tstc() && i--) + (void)getc(); + + /* Check if auto-negotiation is prohibited */ + s = getenv("phy_auto_nego"); + + if (!s || !strcmp(s, "on")) + /* Nothing to do - autonegotiation by default */ + return 0; + + for (i = 0; i < 2; i++) { + ret = miiphy_read("FEC ETHERNET", phy[i], PHY_BMCR, ®); + if (ret) { + printf("Cannot read BMCR on PHY %d\n", phy[i]); + return 0; + } + /* Auto-negotiation off, hard set full duplex, 100Mbps */ + ret = miiphy_write("FEC ETHERNET", phy[i], + PHY_BMCR, (reg | PHY_BMCR_100MB | + PHY_BMCR_DPLX) & ~PHY_BMCR_AUTON); + if (ret) { + printf("Cannot write BMCR on PHY %d\n", phy[i]); + return 0; + } + } + + return 0; +} + +#endif + /* ------------------------------------------------------------------------- */ diff --git a/include/configs/TK885D.h b/include/configs/TK885D.h new file mode 100644 index 0000000000..761a35276b --- /dev/null +++ b/include/configs/TK885D.h @@ -0,0 +1,513 @@ +/* + * (C) Copyright 2000-2005 + * Wolfgang Denk, DENX Software Engineering, wd@denx.de. + * + * (C) Copyright 2006 + * Martin Krause, TQ-Systems GmBH, martin.krause@tqs.de + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +/* + * board/config.h - configuration options, board specific + */ + +#ifndef __CONFIG_H +#define __CONFIG_H + +/* + * High Level Configuration Options + * (easy to change) + */ + +#define CONFIG_MPC885 1 /* This is a MPC885 CPU */ +#define CONFIG_TQM885D 1 /* ...on a TQM88D module */ +#define CONFIG_TK885D 1 /* ...in a TK885D base board */ + +#define CONFIG_8xx_OSCLK 10000000 /* 10 MHz - PLL input clock */ +#define CFG_8xx_CPUCLK_MIN 15000000 /* 15 MHz - CPU minimum clock */ +#define CFG_8xx_CPUCLK_MAX 133000000 /* 133 MHz - CPU maximum clock */ +#define CONFIG_8xx_CPUCLK_DEFAULT 66000000 /* 66 MHz - CPU default clock */ + /* (it will be used if there is no */ + /* 'cpuclk' variable with valid value) */ + +#define CONFIG_8xx_CONS_SMC1 1 /* Console is on SMC1 */ + +#define CONFIG_BAUDRATE 115200 /* console baudrate = 115kbps */ + +#define CONFIG_BOOTCOUNT_LIMIT + +#define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */ + +#define CONFIG_BOARD_TYPES 1 /* support board types */ + +#define CONFIG_PREBOOT "echo;" \ + "echo Type \"run flash_nfs\" to mount root filesystem over NFS;" \ + "echo" + +#undef CONFIG_BOOTARGS + +#define CONFIG_EXTRA_ENV_SETTINGS \ + "netdev=eth0\0" \ + "nfsargs=setenv bootargs root=/dev/nfs rw " \ + "nfsroot=${serverip}:${rootpath}\0" \ + "ramargs=setenv bootargs root=/dev/ram rw\0" \ + "addip=setenv bootargs ${bootargs} " \ + "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}" \ + ":${hostname}:${netdev}:off panic=1\0" \ + "flash_nfs=run nfsargs addip;" \ + "bootm ${kernel_addr}\0" \ + "flash_self=run ramargs addip;" \ + "bootm ${kernel_addr} ${ramdisk_addr}\0" \ + "net_nfs=tftp 200000 ${bootfile};run nfsargs addip;bootm\0" \ + "rootpath=/opt/eldk/ppc_8xx\0" \ + "bootfile=/tftpboot/TQM885D/uImage\0" \ + "kernel_addr=40080000\0" \ + "ramdisk_addr=40180000\0" \ + "load=tftp 200000 ${u-boot}\0" \ + "update=protect off 40000000 +${filesize};" \ + "erase 40000000 +${filesize};" \ + "cp.b 200000 40000000 ${filesize};" \ + "protect on 40000000 +${filesize}\0" \ + "" +#define CONFIG_BOOTCOMMAND "run flash_self" + +#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ +#undef CFG_LOADS_BAUD_CHANGE /* don't allow baudrate change */ + +#undef CONFIG_WATCHDOG /* watchdog disabled */ + +#define CONFIG_STATUS_LED 1 /* Status LED enabled */ + +#undef CONFIG_CAN_DRIVER /* CAN Driver support disabled */ + +/* enable I2C and select the hardware/software driver */ +#undef CONFIG_HARD_I2C /* I2C with hardware support */ +#define CONFIG_SOFT_I2C 1 /* I2C bit-banged */ + +#define CFG_I2C_SPEED 93000 /* 93 kHz is supposed to work */ +#define CFG_I2C_SLAVE 0xFE + +#ifdef CONFIG_SOFT_I2C +/* + * Software (bit-bang) I2C driver configuration + */ +#define PB_SCL 0x00000020 /* PB 26 */ +#define PB_SDA 0x00000010 /* PB 27 */ + +#define I2C_INIT (immr->im_cpm.cp_pbdir |= PB_SCL) +#define I2C_ACTIVE (immr->im_cpm.cp_pbdir |= PB_SDA) +#define I2C_TRISTATE (immr->im_cpm.cp_pbdir &= ~PB_SDA) +#define I2C_READ ((immr->im_cpm.cp_pbdat & PB_SDA) != 0) +#define I2C_SDA(bit) if(bit) immr->im_cpm.cp_pbdat |= PB_SDA; \ + else immr->im_cpm.cp_pbdat &= ~PB_SDA +#define I2C_SCL(bit) if(bit) immr->im_cpm.cp_pbdat |= PB_SCL; \ + else immr->im_cpm.cp_pbdat &= ~PB_SCL +#define I2C_DELAY udelay(2) /* 1/4 I2C clock duration */ +#endif /* CONFIG_SOFT_I2C */ + +#define CFG_I2C_EEPROM_ADDR 0x50 /* EEPROM AT24C?? */ +#define CFG_I2C_EEPROM_ADDR_LEN 2 /* two byte address */ +#define CFG_EEPROM_PAGE_WRITE_BITS 4 +#define CFG_EEPROM_PAGE_WRITE_DELAY_MS 10 /* and takes up to 10 msec */ + +# define CONFIG_RTC_DS1337 1 +# define CFG_I2C_RTC_ADDR 0x68 + +/* + * BOOTP options + */ +#define CONFIG_BOOTP_SUBNETMASK +#define CONFIG_BOOTP_GATEWAY +#define CONFIG_BOOTP_HOSTNAME +#define CONFIG_BOOTP_BOOTPATH +#define CONFIG_BOOTP_BOOTFILESIZE + + +#define CONFIG_MAC_PARTITION +#define CONFIG_DOS_PARTITION + +#undef CONFIG_RTC_MPC8xx /* MPC885 does not support RTC */ + +#define CONFIG_TIMESTAMP /* but print image timestmps */ + + +/* + * Command line configuration. + */ +#include + +#define CONFIG_CMD_ASKENV +#define CONFIG_CMD_DATE +#define CONFIG_CMD_DHCP +#define CONFIG_CMD_EEPROM +#define CONFIG_CMD_I2C +#define CONFIG_CMD_IDE +#define CONFIG_CMD_MII +#define CONFIG_CMD_NFS +#define CONFIG_CMD_PING + + +/* + * Miscellaneous configurable options + */ +#define CFG_LONGHELP /* undef to save memory */ +#define CFG_PROMPT "=> " /* Monitor Command Prompt */ + +#define CONFIG_CMDLINE_EDITING 1 /* add command line history */ +#define CFG_HUSH_PARSER 1 /* Use the HUSH parser */ +#ifdef CFG_HUSH_PARSER +#define CFG_PROMPT_HUSH_PS2 "> " +#endif + +#if defined(CONFIG_CMD_KGDB) +#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */ +#else +#define CFG_CBSIZE 256 /* Console I/O Buffer Size */ +#endif +#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */ +#define CFG_MAXARGS 16 /* max number of command args */ +#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */ + +#define CFG_MEMTEST_START 0x0100000 /* memtest works on */ +#define CFG_MEMTEST_END 0x0300000 /* 1 ... 3 MB in DRAM */ +#define CFG_ALT_MEMTEST /* alternate, more extensive + memory test.*/ + +#define CFG_LOAD_ADDR 0x100000 /* default load address */ + +#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */ + +#define CFG_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 } + +/* + * Enable loopw command. + */ +#define CONFIG_LOOPW + +/* + * Low Level Configuration Settings + * (address mappings, register initial values, etc.) + * You should know what you are doing if you make changes here. + */ +/*----------------------------------------------------------------------- + * Internal Memory Mapped Register + */ +#define CFG_IMMR 0xFFF00000 + +/*----------------------------------------------------------------------- + * Definitions for initial stack pointer and data area (in DPRAM) + */ +#define CFG_INIT_RAM_ADDR CFG_IMMR +#define CFG_INIT_RAM_END 0x2F00 /* End of used area in DPRAM */ +#define CFG_GBL_DATA_SIZE 64 /* size in bytes reserved for initial data */ +#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE) +#define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET + +/*----------------------------------------------------------------------- + * Start addresses for the final memory configuration + * (Set up by the startup code) + * Please note that CFG_SDRAM_BASE _must_ start at 0 + */ +#define CFG_SDRAM_BASE 0x00000000 +#define CFG_FLASH_BASE 0x40000000 +#define CFG_MONITOR_LEN (256 << 10) /* Reserve 256 kB for Monitor */ +#define CFG_MONITOR_BASE CFG_FLASH_BASE +#define CFG_MALLOC_LEN (256 << 10) /* Reserve 128 kB for malloc() */ + +/* + * For booting Linux, the board info and command line data + * have to be in the first 8 MB of memory, since this is + * the maximum mapped by the Linux kernel during initialization. + */ +#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ + +/*----------------------------------------------------------------------- + * FLASH organization + */ + +/* use CFI flash driver */ +#define CFG_FLASH_CFI 1 /* Flash is CFI conformant */ +#define CFG_FLASH_CFI_DRIVER 1 /* Use the common driver */ +#define CFG_FLASH_BANKS_LIST { CFG_FLASH_BASE } +#define CFG_FLASH_EMPTY_INFO +#define CFG_FLASH_USE_BUFFER_WRITE 1 +#define CFG_MAX_FLASH_BANKS 1 /* max number of memory banks */ +#define CFG_MAX_FLASH_SECT 256 /* max number of sectors on one chip */ + +#define CFG_ENV_IS_IN_FLASH 1 +#define CFG_ENV_OFFSET 0x40000 /* Offset of Environment Sector */ +#define CFG_ENV_SIZE 0x08000 /* Total Size of Environment */ +#define CFG_ENV_SECT_SIZE 0x20000 /* Total Size of Environment Sector */ + +/* Address and size of Redundant Environment Sector */ +#define CFG_ENV_OFFSET_REDUND (CFG_ENV_OFFSET+CFG_ENV_SECT_SIZE) +#define CFG_ENV_SIZE_REDUND (CFG_ENV_SIZE) + +/*----------------------------------------------------------------------- + * Hardware Information Block + */ +#define CFG_HWINFO_OFFSET 0x0003FFC0 /* offset of HW Info block */ +#define CFG_HWINFO_SIZE 0x00000040 /* size of HW Info block */ +#define CFG_HWINFO_MAGIC 0x54514D38 /* 'TQM8' */ + +/*----------------------------------------------------------------------- + * Cache Configuration + */ +#define CFG_CACHELINE_SIZE 16 /* For all MPC8xx CPUs */ +#if defined(CONFIG_CMD_KGDB) +#define CFG_CACHELINE_SHIFT 4 /* log base 2 of the above value */ +#endif + +/*----------------------------------------------------------------------- + * SYPCR - System Protection Control 11-9 + * SYPCR can only be written once after reset! + *----------------------------------------------------------------------- + * Software & Bus Monitor Timer max, Bus Monitor enable, SW Watchdog freeze + */ +#if defined(CONFIG_WATCHDOG) +#define CFG_SYPCR (SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | \ + SYPCR_SWE | SYPCR_SWRI| SYPCR_SWP) +#else +#define CFG_SYPCR (SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | SYPCR_SWP) +#endif + +/*----------------------------------------------------------------------- + * SIUMCR - SIU Module Configuration 11-6 + *----------------------------------------------------------------------- + * PCMCIA config., multi-function pin tri-state + */ +#ifndef CONFIG_CAN_DRIVER +#define CFG_SIUMCR (SIUMCR_DBGC00 | SIUMCR_DBPC00 | SIUMCR_MLRC01) +#else /* we must activate GPL5 in the SIUMCR for CAN */ +#define CFG_SIUMCR (SIUMCR_DBGC11 | SIUMCR_DBPC00 | SIUMCR_MLRC01) +#endif /* CONFIG_CAN_DRIVER */ + +/*----------------------------------------------------------------------- + * TBSCR - Time Base Status and Control 11-26 + *----------------------------------------------------------------------- + * Clear Reference Interrupt Status, Timebase freezing enabled + */ +#define CFG_TBSCR (TBSCR_REFA | TBSCR_REFB | TBSCR_TBF) + +/*----------------------------------------------------------------------- + * PISCR - Periodic Interrupt Status and Control 11-31 + *----------------------------------------------------------------------- + * Clear Periodic Interrupt Status, Interrupt Timer freezing enabled + */ +#define CFG_PISCR (PISCR_PS | PISCR_PITF) + +/*----------------------------------------------------------------------- + * SCCR - System Clock and reset Control Register 15-27 + *----------------------------------------------------------------------- + * Set clock output, timebase and RTC source and divider, + * power management and some other internal clocks + */ +#define SCCR_MASK SCCR_EBDF11 +#define CFG_SCCR (SCCR_COM00 | SCCR_DFSYNC00 | SCCR_DFBRG00 | \ + SCCR_DFNL000 | SCCR_DFNH000 | SCCR_DFLCD000 | \ + SCCR_DFALCD00) + +/*----------------------------------------------------------------------- + * PCMCIA stuff + *----------------------------------------------------------------------- + * + */ +#define CFG_PCMCIA_MEM_ADDR (0xE0000000) +#define CFG_PCMCIA_MEM_SIZE ( 64 << 20 ) +#define CFG_PCMCIA_DMA_ADDR (0xE4000000) +#define CFG_PCMCIA_DMA_SIZE ( 64 << 20 ) +#define CFG_PCMCIA_ATTRB_ADDR (0xE8000000) +#define CFG_PCMCIA_ATTRB_SIZE ( 64 << 20 ) +#define CFG_PCMCIA_IO_ADDR (0xEC000000) +#define CFG_PCMCIA_IO_SIZE ( 64 << 20 ) + +/*----------------------------------------------------------------------- + * IDE/ATA stuff (Supports IDE harddisk on PCMCIA Adapter) + *----------------------------------------------------------------------- + */ + +#define CONFIG_IDE_8xx_PCCARD 1 /* Use IDE with PC Card Adapter */ + +#undef CONFIG_IDE_8xx_DIRECT /* Direct IDE not supported */ +#undef CONFIG_IDE_LED /* LED for ide not supported */ +#undef CONFIG_IDE_RESET /* reset for ide not supported */ + +#define CFG_IDE_MAXBUS 1 /* max. 1 IDE bus */ +#define CFG_IDE_MAXDEVICE 1 /* max. 1 drive per IDE bus */ + +#define CFG_ATA_IDE0_OFFSET 0x0000 + +#define CFG_ATA_BASE_ADDR CFG_PCMCIA_MEM_ADDR + +/* Offset for data I/O */ +#define CFG_ATA_DATA_OFFSET (CFG_PCMCIA_MEM_SIZE + 0x320) + +/* Offset for normal register accesses */ +#define CFG_ATA_REG_OFFSET (2 * CFG_PCMCIA_MEM_SIZE + 0x320) + +/* Offset for alternate registers */ +#define CFG_ATA_ALT_OFFSET 0x0100 + +/*----------------------------------------------------------------------- + * + *----------------------------------------------------------------------- + * + */ +#define CFG_DER 0 + +/* + * Init Memory Controller: + * + * BR0/1 and OR0/1 (FLASH) + */ + +#define FLASH_BASE0_PRELIM 0x40000000 /* FLASH bank #0 */ +#define FLASH_BASE1_PRELIM 0x60000000 /* FLASH bank #0 */ + +/* used to re-map FLASH both when starting from SRAM or FLASH: + * restrict access enough to keep SRAM working (if any) + * but not too much to meddle with FLASH accesses + */ +#define CFG_REMAP_OR_AM 0x80000000 /* OR addr mask */ +#define CFG_PRELIM_OR_AM 0xE0000000 /* OR addr mask */ + +/* + * FLASH timing: Default value of OR0 after reset + */ +#define CFG_OR_TIMING_FLASH (OR_CSNT_SAM | OR_ACS_MSK | OR_BI | \ + OR_SCY_6_CLK | OR_TRLX) + +#define CFG_OR0_REMAP (CFG_REMAP_OR_AM | CFG_OR_TIMING_FLASH) +#define CFG_OR0_PRELIM (CFG_PRELIM_OR_AM | CFG_OR_TIMING_FLASH) +#define CFG_BR0_PRELIM ((FLASH_BASE0_PRELIM & BR_BA_MSK) | BR_V ) + +#define CFG_OR1_REMAP CFG_OR0_REMAP +#define CFG_OR1_PRELIM CFG_OR0_PRELIM +#define CFG_BR1_PRELIM ((FLASH_BASE1_PRELIM & BR_BA_MSK) | BR_V ) + +/* + * BR2/3 and OR2/3 (SDRAM) + * + */ +#define SDRAM_BASE2_PRELIM 0x00000000 /* SDRAM bank #0 */ +#define SDRAM_BASE3_PRELIM 0x20000000 /* SDRAM bank #1 */ +#define SDRAM_MAX_SIZE (256 << 20) /* max 256 MB per bank */ + +/* SDRAM timing: Multiplexed addresses, GPL5 output to GPL5_A (don't care) */ +#define CFG_OR_TIMING_SDRAM 0x00000A00 + +#define CFG_OR2_PRELIM (CFG_PRELIM_OR_AM | CFG_OR_TIMING_SDRAM ) +#define CFG_BR2_PRELIM ((SDRAM_BASE2_PRELIM & BR_BA_MSK) | BR_MS_UPMA | BR_V ) + +#ifndef CONFIG_CAN_DRIVER +#define CFG_OR3_PRELIM CFG_OR2_PRELIM +#define CFG_BR3_PRELIM ((SDRAM_BASE3_PRELIM & BR_BA_MSK) | BR_MS_UPMA | BR_V ) +#else /* CAN uses CS3#, so we can have only one SDRAM bank anyway */ +#define CFG_CAN_BASE 0xC0000000 /* CAN mapped at 0xC0000000 */ +#define CFG_CAN_OR_AM 0xFFFF8000 /* 32 kB address mask */ +#define CFG_OR3_CAN (CFG_CAN_OR_AM | OR_G5LA | OR_BI) +#define CFG_BR3_CAN ((CFG_CAN_BASE & BR_BA_MSK) | \ + BR_PS_8 | BR_MS_UPMB | BR_V ) +#endif /* CONFIG_CAN_DRIVER */ + +/* + * 4096 Rows from SDRAM example configuration + * 1000 factor s -> ms + * 64 PTP (pre-divider from MPTPR) from SDRAM example configuration + * 4 Number of refresh cycles per period + * 64 Refresh cycle in ms per number of rows + */ +#define CFG_PTA_PER_CLK ((4096 * 64 * 1000) / (4 * 64)) + +/* + * Periodic timer (MAMR[PTx]) for 4 * 7.8 us refresh (= 31.2 us per quad) + * + * CPUclock(MHz) * 31.2 + * CFG_MAMR_PTA = ----------------------------------- with DFBRG = 0 + * 2^(2*SCCR[DFBRG]) * MPTPR_PTP_DIV16 + * + * CPU clock = 15 MHz: CFG_MAMR_PTA = 29 -> 4 * 7.73 us + * CPU clock = 50 MHz: CFG_MAMR_PTA = 97 -> 4 * 7.76 us + * CPU clock = 66 MHz: CFG_MAMR_PTA = 128 -> 4 * 7.75 us + * CPU clock = 133 MHz: CFG_MAMR_PTA = 255 -> 4 * 7.67 us + * + * Value 97 is for 4 * 7.8 us at 50 MHz. So the refresh cycle requirement will + * be met also in the default configuration, i.e. if environment variable + * 'cpuclk' is not set. + */ +#define CFG_MAMR_PTA 128 + +/* + * Memory Periodic Timer Prescaler Register (MPTPR) values. + */ +/* 4 * 7.8 us refresh (= 31.2 us per quad) at 50 MHz and PTA = 97 */ +#define CFG_MPTPR_2BK_4K MPTPR_PTP_DIV16 +/* 4 * 3.9 us refresh (= 15.6 us per quad) at 50 MHz and PTA = 97 */ +#define CFG_MPTPR_2BK_8K MPTPR_PTP_DIV8 + +/* + * MAMR settings for SDRAM + */ + +/* 8 column SDRAM */ +#define CFG_MAMR_8COL ((CFG_MAMR_PTA << MAMR_PTA_SHIFT) | MAMR_PTAE | \ + MAMR_AMA_TYPE_0 | MAMR_DSA_1_CYCL | MAMR_G0CLA_A11 | \ + MAMR_RLFA_1X | MAMR_WLFA_1X | MAMR_TLFA_4X) +/* 9 column SDRAM */ +#define CFG_MAMR_9COL ((CFG_MAMR_PTA << MAMR_PTA_SHIFT) | MAMR_PTAE | \ + MAMR_AMA_TYPE_1 | MAMR_DSA_1_CYCL | MAMR_G0CLA_A10 | \ + MAMR_RLFA_1X | MAMR_WLFA_1X | MAMR_TLFA_4X) +/* 10 column SDRAM */ +#define CFG_MAMR_10COL ((CFG_MAMR_PTA << MAMR_PTA_SHIFT) | MAMR_PTAE | \ + MAMR_AMA_TYPE_2 | MAMR_DSA_1_CYCL | MAMR_G0CLA_A9 | \ + MAMR_RLFA_1X | MAMR_WLFA_1X | MAMR_TLFA_4X) + +/* + * Internal Definitions + * + * Boot Flags + */ +#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */ +#define BOOTFLAG_WARM 0x02 /* Software reboot */ + +/* + * Network configuration + */ +#define CONFIG_FEC_ENET /* enable ethernet on FEC */ +#define CONFIG_ETHER_ON_FEC1 /* ... for FEC1 */ +#define CONFIG_ETHER_ON_FEC2 /* ... for FEC2 */ + +#define CONFIG_LAST_STAGE_INIT 1 /* Have to configure PHYs for Linux */ + +/* CFG_DISCOVER_PHY only works with FEC if only one interface is enabled */ +#if (!defined(CONFIG_ETHER_ON_FEC1) || !defined(CONFIG_ETHER_ON_FEC2)) +#define CFG_DISCOVER_PHY +#endif + +#ifndef CFG_DISCOVER_PHY +/* PHY addresses - hard wired in hardware */ +#define CONFIG_FEC1_PHY 1 +#define CONFIG_FEC2_PHY 2 +#endif + +#define CONFIG_NET_RETRY_COUNT 3 +#define CONFIG_ETHPRIME "FEC ETHERNET" + +#endif /* __CONFIG_H */