From: Denis Kalashnikov Date: Wed, 19 Jan 2022 10:25:05 +0000 (+0300) Subject: ath79: add support for reset key on MikroTik RB912UAG-2HPnD X-Git-Tag: v22.03.0-rc1~690 X-Git-Url: http://git.lede-project.org./?a=commitdiff_plain;h=ec85e48a113514502563a06c5d0278a57a8b6b86;p=openwrt%2Fstaging%2Fpepe2k.git ath79: add support for reset key on MikroTik RB912UAG-2HPnD On MikroTik RB91x board series a reset key shares SoC gpio line #15 with NAND ALE and NAND IO7. So we need a custom gpio driver to manage this non-trivial connection schema. Also rb91x-nand needs to have an ability to disable a polling of the key while it works with NAND. While we've been integrating rb91x-key into a firmware, we've figured out that: * In the gpio-latch driver we need to add a "cansleep" suffix to several gpiolib calls, * When gpio-latch and rb91x-nand fail to get a gpio and an error is -EPROBE_DEFER, they shouldn't report about this, since this actually is not an error and occurs when the gpio-latch probe function is called before the rb91x-key probe. We fix these related things here too. Signed-off-by: Denis Kalashnikov Reviewed-by: Sergey Ryazanov Tested-by: Koen Vandeputte --- diff --git a/target/linux/ath79/config-5.10 b/target/linux/ath79/config-5.10 index 12f51b08ce..53f444c68b 100644 --- a/target/linux/ath79/config-5.10 +++ b/target/linux/ath79/config-5.10 @@ -74,6 +74,7 @@ CONFIG_GPIO_74X164=y CONFIG_GPIO_ATH79=y CONFIG_GPIO_GENERIC=y # CONFIG_GPIO_LATCH is not set +# CONFIG_GPIO_RB91X_KEY is not set CONFIG_HANDLE_DOMAIN_IRQ=y CONFIG_HARDWARE_WATCHPOINTS=y CONFIG_HAS_DMA=y diff --git a/target/linux/ath79/dts/ar9342_mikrotik_routerboard-912uag-2hpnd.dts b/target/linux/ath79/dts/ar9342_mikrotik_routerboard-912uag-2hpnd.dts index 77a0d29113..b7ab1cacdb 100644 --- a/target/linux/ath79/dts/ar9342_mikrotik_routerboard-912uag-2hpnd.dts +++ b/target/linux/ath79/dts/ar9342_mikrotik_routerboard-912uag-2hpnd.dts @@ -16,6 +16,13 @@ led-upgrade = &led_power; }; + gpio_key: gpio_key { + compatible = "mikrotik,gpio-rb91x-key"; + gpio-controller; + #gpio-cells = <2>; + gpio = <&gpio 15 GPIO_ACTIVE_HIGH>; + }; + gpio_latch: gpio_latch { compatible = "gpio-latch"; gpio-controller; @@ -27,7 +34,7 @@ <0>, /* Not connected */ <&gpio 13 GPIO_ACTIVE_HIGH>, <&gpio 14 GPIO_ACTIVE_HIGH>, - <&gpio 15 GPIO_ACTIVE_HIGH>, + <&gpio_key 0 GPIO_ACTIVE_HIGH>, <&gpio 11 GPIO_ACTIVE_LOW>; /* Latch Enable */ }; @@ -40,7 +47,8 @@ <&gpio_latch 6 GPIO_ACTIVE_HIGH>, /* Command Latch Enable (CLE) */ <&gpio_latch 7 GPIO_ACTIVE_HIGH>, /* Address Latch Enable (ALE) */ <&gpio 12 GPIO_ACTIVE_LOW>, /* Read/Write Enable (nRW) */ - <&gpio_latch 8 GPIO_ACTIVE_LOW>; /* Latch Enable (nLE) */ + <&gpio_latch 8 GPIO_ACTIVE_LOW>, /* Latch Enable (nLE) */ + <&gpio_key 2 GPIO_ACTIVE_HIGH>; /* Key poll disable */ partitions { compatible = "fixed-partitions"; @@ -64,6 +72,17 @@ }; }; + keys { + compatible = "gpio-keys-polled"; + poll-interval = <20>; + + button@0 { + label = "reset"; + linux,code = ; + gpios = <&gpio_key 1 GPIO_ACTIVE_LOW>; + }; + }; + leds { compatible = "gpio-leds"; diff --git a/target/linux/ath79/files/drivers/gpio/gpio-latch.c b/target/linux/ath79/files/drivers/gpio/gpio-latch.c index f3545a663e..976e683230 100644 --- a/target/linux/ath79/files/drivers/gpio/gpio-latch.c +++ b/target/linux/ath79/files/drivers/gpio/gpio-latch.c @@ -62,7 +62,7 @@ gpio_latch_get(struct gpio_chip *gc, unsigned offset) int ret; gpio_latch_lock(glc, false); - ret = gpiod_get_value(glc->gpios[offset]); + ret = gpiod_get_raw_value_cansleep(glc->gpios[offset]); gpio_latch_unlock(glc, false); return ret; @@ -81,7 +81,7 @@ gpio_latch_set(struct gpio_chip *gc, unsigned offset, int value) } gpio_latch_lock(glc, enable_latch); - gpiod_set_raw_value(glc->gpios[offset], value); + gpiod_set_raw_value_cansleep(glc->gpios[offset], value); gpio_latch_unlock(glc, disable_latch); } @@ -133,8 +133,10 @@ static int gpio_latch_probe(struct platform_device *pdev) glc->gpios[i] = devm_gpiod_get_index_optional(dev, NULL, i, GPIOD_OUT_LOW); if (IS_ERR(glc->gpios[i])) { - dev_err(dev, "failed to get gpio %d: %d\n", i, - PTR_ERR(glc->gpios[i])); + if (PTR_ERR(glc->gpios[i]) != -EPROBE_DEFER) { + dev_err(dev, "failed to get gpio %d: %d\n", i, + PTR_ERR(glc->gpios[i])); + } return PTR_ERR(glc->gpios[i]); } } diff --git a/target/linux/ath79/files/drivers/gpio/gpio-rb91x-key.c b/target/linux/ath79/files/drivers/gpio/gpio-rb91x-key.c new file mode 100644 index 0000000000..ee8359e774 --- /dev/null +++ b/target/linux/ath79/files/drivers/gpio/gpio-rb91x-key.c @@ -0,0 +1,218 @@ +// SPDX-License-Identifier: GPL-2.0-or-later +/* + * Driver for reset key gpio line on MikroTik RB91x board series. + * This line is shared between NAND ALE (goes through a latch), + * NAND IO7 and reset key. We make 3 virtual gpio lines from the + * single physical one: + * 1) Capable output one for NAND, + * 2) Capable input one for reset key, + * 3) And capable output one, aka "key-poll-disable", + * for NAND -- to syncronise NAND operation and key polling. + * + * Copyright (C) 2021 Denis Kalashnikov + */ + +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include + +#define GPIO_RB91X_KEY_DRIVER_NAME "gpio-rb91x-key" + +enum gpio_rb91x_key_gpios { + GPIO_RB91X_KEY_NAND, + GPIO_RB91X_KEY_POLL, + GPIO_RB91X_KEY_PDIS, + + GPIO_RB91X_KEY_NGPIOS, +}; + +struct gpio_rb91x_key { + struct gpio_chip gc; + struct mutex mutex; + struct mutex poll_mutex; + int polling_disabled; + struct gpio_desc *gpio; +}; + +static inline struct gpio_rb91x_key *to_gpio_rb91x_key(struct gpio_chip *gc) +{ + return container_of(gc, struct gpio_rb91x_key, gc); +} + +static int gpio_rb91x_key_get(struct gpio_chip *gc, unsigned offset) +{ + struct gpio_rb91x_key *drvdata = to_gpio_rb91x_key(gc); + struct gpio_desc *gpio = drvdata->gpio; + int val, bak_val; + + switch (offset) { + case GPIO_RB91X_KEY_NAND: + mutex_lock(&drvdata->mutex); + val = gpiod_get_value_cansleep(gpio); + mutex_unlock(&drvdata->mutex); + break; + case GPIO_RB91X_KEY_PDIS: + mutex_lock(&drvdata->mutex); + val = drvdata->polling_disabled; + mutex_unlock(&drvdata->mutex); + break; + case GPIO_RB91X_KEY_POLL: + mutex_lock(&drvdata->poll_mutex); + mutex_lock(&drvdata->mutex); + bak_val = gpiod_get_raw_value_cansleep(gpio); + gpiod_direction_input(gpio); + /* + * Without this delay nothing works. Get it + * from mikrotik RouterOS linux kernel patches. + */ + udelay(200); + val = gpiod_get_raw_value_cansleep(gpio); + gpiod_direction_output_raw(gpio, bak_val); + mutex_unlock(&drvdata->mutex); + mutex_unlock(&drvdata->poll_mutex); + break; + default: + return -EINVAL; + } + + return val; +} + +static int gpio_rb91x_key_direction_input(struct gpio_chip *gc, unsigned offset) +{ + switch (offset) { + case GPIO_RB91X_KEY_POLL: + return 0; + default: + return -EINVAL; + } +} + +static void gpio_rb91x_key_set(struct gpio_chip *gc, unsigned offset, int value) +{ + struct gpio_rb91x_key *drvdata = to_gpio_rb91x_key(gc); + struct gpio_desc *gpio = drvdata->gpio; + + mutex_lock(&drvdata->mutex); + + switch (offset) { + case GPIO_RB91X_KEY_NAND: + gpiod_set_raw_value_cansleep(gpio, value); + break; + case GPIO_RB91X_KEY_PDIS: + if (value) { + if (!drvdata->polling_disabled) { + mutex_lock(&drvdata->poll_mutex); + drvdata->polling_disabled = 1; + } + } else { + if (drvdata->polling_disabled) { + mutex_unlock(&drvdata->poll_mutex); + drvdata->polling_disabled = 0; + } + } + break; + default: + break; + } + + mutex_unlock(&drvdata->mutex); +} + +static int gpio_rb91x_key_direction_output(struct gpio_chip *gc, unsigned offset, + int value) +{ + switch (offset) { + case GPIO_RB91X_KEY_NAND: + case GPIO_RB91X_KEY_PDIS: + gpio_rb91x_key_set(gc, offset, value); + return 0; + default: + return -EINVAL; + } +} + +static int gpio_rb91x_key_probe(struct platform_device *pdev) +{ + struct gpio_rb91x_key *drvdata; + struct gpio_chip *gc; + struct device *dev = &pdev->dev; + struct device_node *of_node = dev->of_node; + int r; + + drvdata = devm_kzalloc(dev, sizeof(*drvdata), GFP_KERNEL); + if (!drvdata) + return -ENOMEM; + + mutex_init(&drvdata->mutex); + mutex_init(&drvdata->poll_mutex); + + drvdata->gpio = devm_gpiod_get(dev, NULL, GPIOD_OUT_LOW); + if (IS_ERR(drvdata->gpio)) { + if (PTR_ERR(drvdata->gpio) != -EPROBE_DEFER) { + dev_err(dev, "failed to get gpio: %ld\n", + PTR_ERR(drvdata->gpio)); + } + return PTR_ERR(drvdata->gpio); + } + + gc = &drvdata->gc; + gc->label = GPIO_RB91X_KEY_DRIVER_NAME; + gc->can_sleep = 1; + gc->base = -1; + gc->ngpio = GPIO_RB91X_KEY_NGPIOS; + gc->get = gpio_rb91x_key_get; + gc->set = gpio_rb91x_key_set; + gc->direction_output = gpio_rb91x_key_direction_output; + gc->direction_input = gpio_rb91x_key_direction_input; + gc->of_node = of_node; + + platform_set_drvdata(pdev, drvdata); + + r = gpiochip_add(&drvdata->gc); + if (r) { + dev_err(dev, "gpiochip_add() failed: %d\n", r); + return r; + } + + return 0; +} + +static int gpio_rb91x_key_remove(struct platform_device *pdev) +{ + struct gpio_rb91x_key *drvdata = platform_get_drvdata(pdev); + + gpiochip_remove(&drvdata->gc); + return 0; +} + +static const struct of_device_id gpio_rb91x_key_match[] = { + { .compatible = "mikrotik,"GPIO_RB91X_KEY_DRIVER_NAME }, + {}, +}; + +MODULE_DEVICE_TABLE(of, gpio_rb91x_key_match); + +static struct platform_driver gpio_rb91x_key_driver = { + .probe = gpio_rb91x_key_probe, + .remove = gpio_rb91x_key_remove, + .driver = { + .name = GPIO_RB91X_KEY_DRIVER_NAME, + .owner = THIS_MODULE, + .of_match_table = gpio_rb91x_key_match, + }, +}; + +module_platform_driver(gpio_rb91x_key_driver); + +MODULE_DESCRIPTION("Driver for reset key gpio line shared with NAND for MikroTik RB91x board series."); +MODULE_AUTHOR("Denis Kalashnikov "); +MODULE_LICENSE("GPL v2"); +MODULE_ALIAS("platform:" GPIO_RB91X_KEY_DRIVER_NAME); diff --git a/target/linux/ath79/files/drivers/mtd/nand/raw/rb91x_nand.c b/target/linux/ath79/files/drivers/mtd/nand/raw/rb91x_nand.c index ac9a2ac8ac..244fd27590 100644 --- a/target/linux/ath79/files/drivers/mtd/nand/raw/rb91x_nand.c +++ b/target/linux/ath79/files/drivers/mtd/nand/raw/rb91x_nand.c @@ -40,6 +40,7 @@ enum rb91x_nand_gpios { RB91X_NAND_ALE, /* Address Latch Enable */ RB91X_NAND_NRW, /* Read/Write. Active low */ RB91X_NAND_NLE, /* Latch Enable. Active low */ + RB91X_NAND_PDIS, /* Reset Key Poll Disable. Active high */ RB91X_NAND_GPIOS, }; @@ -57,6 +58,12 @@ static inline void rb91x_nand_latch_lock(struct rb91x_nand_drvdata *drvdata, gpiod_set_value_cansleep(drvdata->gpio[RB91X_NAND_NLE], lock); } +static inline void rb91x_nand_rst_key_poll_disable(struct rb91x_nand_drvdata *drvdata, + int disable) +{ + gpiod_set_value_cansleep(drvdata->gpio[RB91X_NAND_PDIS], disable); +} + static int rb91x_ooblayout_ecc(struct mtd_info *mtd, int section, struct mtd_oob_region *oobregion) { @@ -115,6 +122,7 @@ static void rb91x_nand_write(struct rb91x_nand_drvdata *drvdata, unsigned i; rb91x_nand_latch_lock(drvdata, 1); + rb91x_nand_rst_key_poll_disable(drvdata, 1); oe_reg = __raw_readl(base + AR71XX_GPIO_REG_OE); out_reg = __raw_readl(base + AR71XX_GPIO_REG_OUT); @@ -146,6 +154,7 @@ static void rb91x_nand_write(struct rb91x_nand_drvdata *drvdata, /* Flush write */ __raw_readl(base + AR71XX_GPIO_REG_OUT); + rb91x_nand_rst_key_poll_disable(drvdata, 0); rb91x_nand_latch_lock(drvdata, 0); } @@ -162,6 +171,7 @@ static void rb91x_nand_read(struct rb91x_nand_drvdata *drvdata, gpiod_set_value_cansleep(drvdata->gpio[RB91X_NAND_READ], 1); rb91x_nand_latch_lock(drvdata, 1); + rb91x_nand_rst_key_poll_disable(drvdata, 1); /* Save registers */ oe_reg = __raw_readl(base + AR71XX_GPIO_REG_OE); @@ -199,6 +209,7 @@ static void rb91x_nand_read(struct rb91x_nand_drvdata *drvdata, /* Flush write */ __raw_readl(base + AR71XX_GPIO_REG_OUT); + rb91x_nand_rst_key_poll_disable(drvdata, 0); rb91x_nand_latch_lock(drvdata, 0); /* Disable read mode */ @@ -274,8 +285,11 @@ static int rb91x_nand_probe(struct platform_device *pdev) gpios = gpiod_get_array(dev, NULL, GPIOD_OUT_LOW); if (IS_ERR(gpios)) { - dev_err(dev, "failed to get gpios: %d\n", (int)gpios); - return -EINVAL; + if (PTR_ERR(gpios) != -EPROBE_DEFER) { + dev_err(dev, "failed to get gpios: %d\n", + PTR_ERR(gpios)); + } + return PTR_ERR(gpios); } if (gpios->ndescs != RB91X_NAND_GPIOS) { diff --git a/target/linux/ath79/mikrotik/config-default b/target/linux/ath79/mikrotik/config-default index ee2e4ebe9a..2ff8a14f1d 100644 --- a/target/linux/ath79/mikrotik/config-default +++ b/target/linux/ath79/mikrotik/config-default @@ -1,6 +1,7 @@ CONFIG_CRC16=y CONFIG_CRYPTO_DEFLATE=y CONFIG_GPIO_LATCH=y +CONFIG_GPIO_RB91X_KEY=y CONFIG_GPIO_RB4XX=y CONFIG_GPIO_WATCHDOG=y CONFIG_GPIO_WATCHDOG_ARCH_INITCALL=y diff --git a/target/linux/ath79/patches-5.10/939-mikrotik-rb91x.patch b/target/linux/ath79/patches-5.10/939-mikrotik-rb91x.patch index 5bbab93c51..4f4344b40f 100644 --- a/target/linux/ath79/patches-5.10/939-mikrotik-rb91x.patch +++ b/target/linux/ath79/patches-5.10/939-mikrotik-rb91x.patch @@ -14,6 +14,17 @@ config GPIO_LOGICVC tristate "Xylon LogiCVC GPIO support" depends on MFD_SYSCON && OF +@@ -495,6 +502,10 @@ config GPIO_REG + A 32-bit single register GPIO fixed in/out implementation. This + can be used to represent any register as a set of GPIO signals. + ++config GPIO_RB91X_KEY ++ tristate "MikroTik RB91x board series reset key support" ++ depends on ATH79 ++ + config GPIO_SAMA5D2_PIOBU + tristate "SAMA5D2 PIOBU GPIO support" + depends on MFD_SYSCON --- a/drivers/gpio/Makefile +++ b/drivers/gpio/Makefile @@ -72,6 +72,7 @@ obj-$(CONFIG_GPIO_IT87) += gpio-it87.o @@ -24,6 +35,14 @@ obj-$(CONFIG_GPIO_LOGICVC) += gpio-logicvc.o obj-$(CONFIG_GPIO_LOONGSON1) += gpio-loongson1.o obj-$(CONFIG_GPIO_LOONGSON) += gpio-loongson.o +@@ -121,6 +122,7 @@ obj-$(CONFIG_GPIO_PMIC_EIC_SPRD) += gpio + obj-$(CONFIG_GPIO_PXA) += gpio-pxa.o + obj-$(CONFIG_GPIO_RASPBERRYPI_EXP) += gpio-raspberrypi-exp.o + obj-$(CONFIG_GPIO_RB4XX) += gpio-rb4xx.o ++obj-$(CONFIG_GPIO_RB91X_KEY) += gpio-rb91x-key.o + obj-$(CONFIG_GPIO_RC5T583) += gpio-rc5t583.o + obj-$(CONFIG_GPIO_RCAR) += gpio-rcar.o + obj-$(CONFIG_GPIO_RDA) += gpio-rda.o --- a/drivers/mtd/nand/raw/Kconfig +++ b/drivers/mtd/nand/raw/Kconfig @@ -571,4 +571,10 @@ config MTD_NAND_RB4XX