From: Tomasz Maciej Nowak Date: Fri, 14 Aug 2020 16:03:40 +0000 (+0200) Subject: ath79: add support for ALLNET ALL-WAP02860AC X-Git-Url: http://git.lede-project.org./?a=commitdiff_plain;h=ebf71533f9123d9ca182154a55af5e2904460a25;p=openwrt%2Fstaging%2Fansuel.git ath79: add support for ALLNET ALL-WAP02860AC ALLNET ALL-WAP02860AC is a dual-band wireless access point. Specification SoC: Qualcomm Atheros QCA9558 RAM: 128 MB DDR2 Flash: 16 MB SPI NOR WIFI: 2.4 GHz 3T3R integrated 5 GHz 3T3R QCA9880 Mini PCIe card Ethernet: 1x 10/100/1000 Mbps AR8035-A, PoE capable (802.3at) LEDS: 5x, which four are GPIO controlled Buttons: 1x GPIO controlled UART: 4 pin header near Mini PCIe card, starting count from white triangle on PCB 1. VCC 3.3V, 2. GND, 3. TX, 4. RX baud: 115200, parity: none, flow control: none MAC addresses Calibration data does not contain valid MAC addresses. The calculated MAC addresses are chosen in accordance with OEM firmware. Because of: a) constrained environment (SNMP) when connecting through Telnet or SSH, b) hard-coded kernel and rootfs sizes, c) checksum verification of kerenel and rootfs images in bootloder, creating factory image accepted by OEM web interface is difficult, therefore, to install OpenWrt on this device UART connection is needed. The teardown is simple, unscrew four screws to disassemble the casing, plus two screws to separate mainboard from the casing. Before flashing, be sure to have a copy of factory firmware, in case You wish to revert to original firmware. Installation 1. Prepare TFTP server with OpenWrt initramfs-kernel image. 2. Connect to LAN port. 3. Connect to UART port. 4. Power on the device and when prompted to stop autoboot, hit any key. 5. Alter U-Boot environment with following commands: setenv failsafe_boot bootm 0x9f0a0000 saveenv 6. Adjust "ipaddr" and "serverip" addresses in U-Boot environment, use 'setenv' to do that, then run following commands: tftpboot 0x81000000 bootm 0x81000000 7. Wait about 1 minute for OpenWrt to boot. 8. Transfer OpenWrt sysupgrade image to /tmp directory and flash it with: sysupgrade -n /tmp/ 9. After flashing, the access point will reboot to OpenWrt. Wait few minutes, until the Power LED stops blinking, then it's ready for configuration. Signed-off-by: Tomasz Maciej Nowak [add MAC address comment to commit message] Signed-off-by: Adrian Schmutzler --- diff --git a/package/boot/uboot-envtools/files/ath79 b/package/boot/uboot-envtools/files/ath79 index b00e3fa127..c0873c6e0d 100644 --- a/package/boot/uboot-envtools/files/ath79 +++ b/package/boot/uboot-envtools/files/ath79 @@ -14,6 +14,7 @@ board=$(board_name) case "$board" in alfa-network,ap121f|\ +allnet,all-wap02860ac|\ arduino,yun|\ buffalo,bhr-4grv2|\ devolo,magic-2-wifi|\ diff --git a/target/linux/ath79/dts/qca9558_allnet_all-wap02860ac.dts b/target/linux/ath79/dts/qca9558_allnet_all-wap02860ac.dts new file mode 100644 index 0000000000..6d7eeb2630 --- /dev/null +++ b/target/linux/ath79/dts/qca9558_allnet_all-wap02860ac.dts @@ -0,0 +1,156 @@ +// SPDX-License-Identifier: GPL-2.0-or-later OR MIT +/dts-v1/; + +#include +#include + +#include "qca955x.dtsi" + +/ { + model = "ALLNET ALL-WAP02860AC"; + compatible = "allnet,all-wap02860ac", "qca,qca9558"; + + aliases { + label-mac-device = ð0; + led-boot = &led_power; + led-failsafe = &led_power; + led-running = &led_power; + led-upgrade = &led_power; + }; + + keys { + compatible = "gpio-keys"; + + reset { + label = "reset"; + linux,code = ; + gpios = <&gpio 17 GPIO_ACTIVE_LOW>; + }; + }; + + leds { + compatible = "gpio-leds"; + + led_power: power { + label = "all-wap02860ac:amber:power"; + gpios = <&gpio 22 GPIO_ACTIVE_LOW>; + default-state = "on"; + }; + + wlan2g { + label = "all-wap02860ac:blue:wlan2g"; + gpios = <&gpio 13 GPIO_ACTIVE_LOW>; + linux,default-trigger = "phy1tpt"; + }; + + wlan5g { + label = "all-wap02860ac:green:wlan5g"; + gpios = <&gpio 23 GPIO_ACTIVE_LOW>; + linux,default-trigger = "phy0tpt"; + }; + + wps { + label = "all-wap02860ac:blue:wps"; + gpios = <&gpio 19 GPIO_ACTIVE_LOW>; + }; + }; +}; + +ð0 { + status = "okay"; + + pll-data = <0x8e000000 0x80000101 0x80001313>; + phy-handle = <&phy5>; + phy-mode = "rgmii-rxid"; + + mtd-mac-address = <&art 0x0>; +}; + +&mdio0 { + status = "okay"; + + phy5: ethernet-phy@5 { + reg = <5>; + eee-broken-100tx; + eee-broken-1000t; + }; +}; + +&pcie0 { + status = "okay"; + + wifi@0,0 { + compatible = "qcom,ath10k"; + reg = <0 0 0 0 0>; + }; +}; + +&pll { + clocks = <&extosc>; +}; + +&spi { + status = "okay"; + + num-cs = <1>; + + flash@0 { + compatible = "jedec,spi-nor"; + reg = <0>; + spi-max-frequency = <25000000>; + + partitions { + compatible = "fixed-partitions"; + #address-cells = <1>; + #size-cells = <1>; + + partition@0 { + label = "u-boot"; + reg = <0x000000 0x040000>; + read-only; + }; + + partition@40000 { + label = "u-boot-env"; + reg = <0x040000 0x010000>; + }; + + partition@50000 { + label = "custom"; + reg = <0x050000 0x050000>; + read-only; + }; + + partition@a0000 { + compatible = "denx,uimage"; + label = "firmware"; + reg = <0x0a0000 0xcd0000>; + }; + + partition@d70000 { + label = "failsafe"; + reg = <0xd70000 0x280000>; + read-only; + }; + + art: partition@ff0000 { + label = "art"; + reg = <0xff0000 0x010000>; + read-only; + }; + }; + }; +}; + +&uart { + status = "okay"; +}; + +&wmac { + status = "okay"; + + mtd-cal-data = <&art 0x1000>; + mtd-mac-address = <&art 0x0>; + mtd-mac-address-increment = <1>; + qca-no-eeprom; +}; diff --git a/target/linux/ath79/generic/base-files/etc/board.d/02_network b/target/linux/ath79/generic/base-files/etc/board.d/02_network index 4195332ae2..f655abe740 100755 --- a/target/linux/ath79/generic/base-files/etc/board.d/02_network +++ b/target/linux/ath79/generic/base-files/etc/board.d/02_network @@ -11,6 +11,7 @@ ath79_setup_interfaces() case "$board" in adtran,bsap1800-v2|\ adtran,bsap1840|\ + allnet,all-wap02860ac|\ alfa-network,ap121f|\ arduino,yun|\ aruba,ap-105|\ diff --git a/target/linux/ath79/generic/base-files/etc/hotplug.d/firmware/11-ath10k-caldata b/target/linux/ath79/generic/base-files/etc/hotplug.d/firmware/11-ath10k-caldata index 19e20c7d36..1c93fe332c 100644 --- a/target/linux/ath79/generic/base-files/etc/hotplug.d/firmware/11-ath10k-caldata +++ b/target/linux/ath79/generic/base-files/etc/hotplug.d/firmware/11-ath10k-caldata @@ -10,6 +10,11 @@ board=$(board_name) case "$FIRMWARE" in "ath10k/cal-pci-0000:00:00.0.bin") case $board in + allnet,all-wap02860ac|\ + glinet,gl-x750) + caldata_extract "art" 0x5000 0x844 + ath10k_patch_mac $(macaddr_add $(mtd_get_mac_binary art 0x0) +2) + ;; avm,fritz1750e|\ avm,fritzdvbc) caldata_extract "urlader" 0x198a 0x844 @@ -72,10 +77,6 @@ case "$FIRMWARE" in caldata_extract "art" 0x5000 0x844 ath10k_patch_mac $(macaddr_add $(mtd_get_mac_binary art 0x0) +1) ;; - glinet,gl-x750) - caldata_extract "art" 0x5000 0x844 - ath10k_patch_mac $(macaddr_add $(mtd_get_mac_binary art 0x0) +2) - ;; nec,wg800hp) caldata_extract "art" 0x5000 0x844 ath10k_patch_mac $(mtd_get_mac_text board_data 0x880) diff --git a/target/linux/ath79/image/generic.mk b/target/linux/ath79/image/generic.mk index e2c37f7a57..debb6722ca 100644 --- a/target/linux/ath79/image/generic.mk +++ b/target/linux/ath79/image/generic.mk @@ -210,6 +210,15 @@ define Device/alfa-network_ap121f endef TARGET_DEVICES += alfa-network_ap121f +define Device/allnet_all-wap02860ac + SOC := qca9558 + DEVICE_VENDOR := ALLNET + DEVICE_MODEL := ALL-WAP02860AC + DEVICE_PACKAGES := ath10k-firmware-qca988x-ct kmod-ath10k-ct + IMAGE_SIZE := 13120k +endef +TARGET_DEVICES += allnet_all-wap02860ac + define Device/arduino_yun SOC := ar9331 DEVICE_VENDOR := Arduino